Français dropdown-ico

Humminbird ID 600 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Humminbird ID 600. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Humminbird ID 600 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Humminbird ID 600 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Humminbird ID 600 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Humminbird ID 600
- nom du fabricant et année de fabrication Humminbird ID 600
- instructions d'utilisation, de réglage et d’entretien de l'équipement Humminbird ID 600
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Humminbird ID 600 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Humminbird ID 600 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Humminbird en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Humminbird ID 600, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Humminbird ID 600, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Humminbird ID 600. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    [...]

  • Page 2

    INSTALLATION PREPARATION PARTS SUPPLIED PARTS SUPPLIED Before installing your new Humminbird fish f inder, please ensure the following parts are included in the box: • Fishfinder • Transducer with 20’ (6m) of cable and mounting hardware kit • Mounting system an d mounting hardware kit • 6’ (2m) power cable • Publications kit It any of[...]

  • Page 3

    INSTALLATION PREPARATION INSTALLATION OVERVIEW Determining How to Mount the Transducer Your Humminb ird fishfinder includes a standard transducer. This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat. The transom installation, which is the most widely used, places the transducer on the outside [...]

  • Page 4

    INSTALLATION PREPARATION ALTERNATE M OUNTING METHODS ALTERNATE TRANSDUCERS AND MOUNTING METHODS Your Humminbird fishfinder comes with everything necessary for installation and operation on most boats. However, there are several situations which may require a different type of transducer. In board boats, wood or metal hulls, and sail boats create un[...]

  • Page 5

    INSTALLATION PREPARATION TRANSDUCER EXCHANGE TRANSDUCER EXCHANGE Other transducers are available as replacements for the standard transducer. You may exchange your new and unassembled transducer for another type by returning i t to the address listed in Customer Support. Some transducers may have additional cost. Refer to the Accessory catalog or c[...]

  • Page 6

    INSTALLAT ION TRANSOM INSTALLATION Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This chapter contains information critical to the correct installation of your transducer. Due to the wide variety of b oat hulls, only general instructions are presented in the installation guide. Each bo[...]

  • Page 7

    INSTALLATION TRANSOM INSTALLATION • If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence, and a different mounting technique or transducer type should be considered. Step Two - Drill the Mounting Holes 1. Remove the mounting template from the front of the Operations Manual. 2. Hold the te[...]

  • Page 8

    INSTALLATION TRANSOM INSTALLATION Step Four - Mount the Transducer to the Transom 1. Apply silicone sealant to the mounting holes drilled into the transom. 2. Align the transducer assembly with the drilled holes in the transom (Figure 8). 3. U se either a flat head screwdriver, a 5/16" (8mm) hex driver, or a 5/16" (8mm) socket to mount th[...]

  • Page 9

    mounting bracket. Drill this hole and install the screw after final testing and adjustments have been completed.[...]

  • Page 10

    INSTALLATION TRANSOM INSTALLATION Step Six - Route the Cable There are several ways to route the transducer c able to the to the area where the control head will be installed. The most common procedure routes the cable through the transom into the boat. Inside the boat there is often a channel or conduit used for other wiring that the cable can be [...]

  • Page 11

    INSTALLATION INSIDE THE HULL INSTALLATION INSIDE THE HULL INSTALLATION Inside the hull installation requires the mount system and control head be installed and operational. See Installing the Control Head for instruction on installing the unit. Inside the hull mountin g generally produces good results in single thickness fiberglass - hulled boats. [...]

  • Page 12

    The transducer cannot transmit through air. The water purges any air from between the transducer and the hull and fills any voids in the coarse fiberglass surface.[...]

  • Page 13

    INSTALLATION INSIDE THE HULL INSTALLATION 3. Power up the Control Head. 4. Run the boat at various speeds and water depths while observing the screen on the Control Head. If the unit functions well at low speeds but b egins to skip or miss the bottom at higher speeds, the transducer needs to be moved. If depth performance is required, test the fish[...]

  • Page 14

    INSTALLATION CONTROL HEAD INSTALLATION CONTROL HEAD INSTALLATION Step One - Determine Where to Mount Begin the installation by determining where to mount the control head. Consider the following to determine best location: • The cables for power, transducer and temp/speed accessories (if applicable) should be installed first and must reach the mo[...]

  • Page 15

    fuse in the connection. If you must wire the control head directly to a battery, be sure to install an inline fuse holder[...]

  • Page 16

    INSTALLATION CONTROL HEAD INSTALLATION and one amp fuse (not inc luded) for the protection of the unit (Figure 21). Humminbird is not responsible for over voltage or over current failures. In order to minimize the potential for interference with other marine electronics a separate power source (such as a second batter y) may be necessary. Step Thre[...]

  • Page 17

    Optional: If the ca bles pass outside the mounting bracket, install the hole cover over the hole and fasten in place using the two #8 x 7/8” (22mm) wood screws (Figure 24).[...]

  • Page 18

    INSTALLATION CONTROL HEAD INSTALLATION Step Five - Assembling the Connector Holder 1. Insert the cabl e connectors into the connector holder. The cable connectors are labeled, and there are corresponding labels on the connector holder (Figure 26). The slots for the connectors are keyed to prevent reverse installation, so do not force the connector [...]

  • Page 19

    INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water, however you can initially confirm basic operation with the boat trailered. Press POWER once to turn the unit on. There will be an audible chirp when any button is pressed to confirm the button press. If the unit does not power - up, ensu[...]

  • Page 20

    Installing the SeaScope ID600 Before mounting the SeaScope ID600, gather the parts you need; SeaScope ID600, gimball mounting bracket, mounting hardware kit, power cable, and transducer cable. If the transducer cable is not long enough for your installat ion, see “Accessories” earlier in the manual for information on the EC - 6 10’ extension [...]

  • Page 21

    3. Remove the rear housing and store for f uture use. 4. Drill a 3 1/2 “ hole in the dash or console at the location you have chosen. This is a standard gauge opening size, and hole saws are available at hardware stores, tool rental stores, or marine dealers. 5. Place the SeaScope ID600 in the opening, and mark the four mounting holes from which [...]

  • Page 22

    Section 4: Using the SeaScope ID600 This section provides complete information on operating the SeaScope ID600 through its fro nt panel controls. You are encouraged to read this information completely as you first learn to use the SeaScope ID600. Doing so will ensure you make the most if it many features and functions. The first part of this sectio[...]

  • Page 23

    STOP: Press this to “freeze” the display so you can study it. Press it again to restart the display movement. SELECT: This button is used to access the following functions for further adjustments: • Sensitivity/Units • Bottom Al arm • Fish Alarm • Zoom • Bottom Lock • Display Speed • Depth Range • Fish ID To adjust any of these,[...]

  • Page 24

    range. For example, if you set it at “+2”, Sensitivity remains 2 settings higher that the normal automatic setting. Pressing the ON - OFF button when the SENS menu is displa yed switches the unit of depth measurement between feet, fathoms and meters. Bottom Alarm 2. Using Bottom Alarm; Factory setting; OFF The Bottom Alarm lets you specify the [...]

  • Page 25

    The Fish Alarm alerts you with a chirping sound whenever the SeaScope ID600 detects fish (or another object not attached to the bottom). To activate it, select FISH ALM and press the ON - OFF button. A fish symbol reminds you that the alarm is on. Zoom 4. Using Zoom; Factory setting; OFF Zoom provides an up - close view. To activate it, select Zoom[...]

  • Page 26

    Bottom - Lock provides an up - close view like Z oom, except that in this case the zoomed view automatically moves up or down to stay on the bottom. To use this feature, select BTM LOCK and press ON - OFF. The range of the display is shown when the Bottom - Lock is on. This is an ideal feature for finding structure or locating fish near the bottom.[...]

  • Page 27

    Depth Range 7. Setting Depth Range; Factory setting; On (Auto matic) When you turn the SeaScope ID600 on it finds the bottom, sets the ideal depth range, and automatically adjusts the depth range (to as much as 480 ft) as the depth changes. In this “Auto Depth Range”mode, the bottom is blacked - in for easy - to - unders tand readings. If you p[...]

  • Page 28

    press the ON - OFF button while within the Fish ID menu. Pressing the ON - OFF button again reactivates the ID function.[...]