Français dropdown-ico

Husqvarna 225 HBV manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Husqvarna 225 HBV. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Husqvarna 225 HBV ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Husqvarna 225 HBV décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Husqvarna 225 HBV devrait contenir:
- informations sur les caractéristiques techniques du dispositif Husqvarna 225 HBV
- nom du fabricant et année de fabrication Husqvarna 225 HBV
- instructions d'utilisation, de réglage et d’entretien de l'équipement Husqvarna 225 HBV
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Husqvarna 225 HBV ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Husqvarna 225 HBV et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Husqvarna en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Husqvarna 225 HBV, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Husqvarna 225 HBV, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Husqvarna 225 HBV. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    225 HBV E P A V ersion Operator´s manual Read the operato r ’ s manual carefully and make sure that you understand the contents before using the blowe r . 101 90 68-95[...]

  • Page 2

    Svenska – 31 Sve-5 225/232/235 Bruk 97-11-25, 08.46 31[...]

  • Page 3

    English – 1 CONTENTS Introduction ......................................... 2 Key to symbols .................................... 3 Safety instructions .............................. 4 Description ........................................... 6 Fuel handling ..................................... 1 1 Starting and stopping ....................... 13 [...]

  • Page 4

    2 – English INTRODUCTION ! WARNING! Under no circumstances may the design of the machine be modified without the permission of the manufacturer. Always use genuine accessories. Non-authorised modifications and/or accessories can result in serious personal injury or the death of the operator or others. Your warranty does not cover damage or liabil[...]

  • Page 5

    English – 3 KEY T O SYMBOLS Symbol Description Location Operator ’s manual Blower Symbol Description Location Blower The blower operator must make sure that no bystanders or animals come nearer than 10 metres. Whenever several operators are working in the same work area, they should maintain a safe distance of at least 10 metres from one anothe[...]

  • Page 6

    4 – English Personal safety equipment Fuel safety ! Special safety instructions apply to the type of fuel used for the blower . These instructions are specified under ”Fuel handling” on pages 1 1 and 12. The following instructions apply to persons operating the blower: 1. The operator shall have read and understood the contents of this manual[...]

  • Page 7

    English – 5 1. Do not allow bystanders or animals to be in the work area, i.e. 10 metres from the operator. 2. The blower may throw objects at high velocity that can ricochet and hit the operator. This may cause serious eye damage. 3. Never point the blower nozzle toward people or animals. 4. Stop the engine before fitting or dismantling accessor[...]

  • Page 8

    6 – English DESCRIPTION The blower 1. Shoulder strap 2. Throttle trigger 3. Stop switch 4. Throttle lock 5. Shoulder strap ring 6. Anti-vibration system (inside the housing) 7. Fan housing 8. Fuel cap 9. Air filter 10. Choke 1 1. Inspection cover 12. Cutters 13. Fan impeller 14. Nozzle 15. Blower tube 16. Muffler 17. Start handle 18. Starter devi[...]

  • Page 9

    English – 7 DESCRIPTION Accessories 21. V acuum device with collection components consisting of items 22 - 25 below . 22. V acuum bag tube. 23. Collection bag. 24. V acuum tube in two sections. 25. Auxiliary handle. 25 23 22 24 21[...]

  • Page 10

    8 – English DESCRIPTION 34 2 ! The muffler is designed to give the lowest possible noise level and to direct the engine‘s exhaust fumes away from the operator . Muffler fitted with catalytic converter is also designed to reduce harmful exhaust components. The engine exhaust fumes are hot and can contain sparks, which may cause fire if they come[...]

  • Page 11

    English – 9 DESCRIPTION 24 15 14 7 13 12 1 1 Throttle trigger (2) The speed and the output of the engine are regul- ated by the throttle trigger . The throttle lock (4) must be pressed down before the trigger will actuate the throttle. Fan casing (7) The blower fan casing (7) together with the impeller (13) provide high performance air discharge.[...]

  • Page 12

    10 – English DESCRIPTION 17 18 8 9 19 10 Starter device (18) and starter handle (17) The starter device is located at the top on the engine shrouding and engages in the crank shaft only when the starter handle is pulled. Fuel cap (8) Air filter (9) The fuel cap (14) is located at the top of the engine shrouding and has a gasket, which prevents fu[...]

  • Page 13

    English – 11 Fuel mixture WARNING! Allow adequate ventilation while handling fuel. NOTE! The machine is fitted with a two-stroke engine and must always be run on a mixture of gasoline and two- stroke oil. It is important to measure the quantity of oil accurately , to ensure the correct mixture ratio. Small discrepancies in the amount of oil have [...]

  • Page 14

    12 – English Olja • Olje Olie • Öljyä Lit. 5 10 15 20 2%(1:50) 0,10 0,20 0,30 0,40 Bensin Bensin Benzin Bensiiniä Lit. O FUEL HANDLING Mixture • Always mix gasoline and oil in a clean container intended for fuel. • Always start by filling half the quantity of gasoline required. Then add the entire oil quantity. Mix (shake) the fuel mix[...]

  • Page 15

    English – 13 ST ARTING AND STOPPING WARNING! Never start the blower if the inspection cover is not closed, is damaged or cannot be closed. (Exception: When the vacuum tube is fitted). ! A cold engine should be started in the following manner: 1. Move the stop switch to the start position. 2. Set the choke to the choke position. Setting the chock [...]

  • Page 16

    14 – English USING THE BLOWER WARNING! When fitting the blower tube and nozzle, the engine must be switched off and the stop switch must be in the stop position. ! The blower tube and nozzle have a bayonet mount. Fit them in the following manner: 1. Press the blower tube (15) against the blower air outlet and turn it 90 degrees until a snap is he[...]

  • Page 17

    English – 15 USING THE BLOWER ! WARNING! Never start the blower if the inspection cover is not closed, is damaged or cannot be closed. (Exception: When the vacuum tube is fitted). ! 21 14 WARNING! Do not operate the blower while standing on a ladder or a stand. High-velocity nozzle (21) The high-velocity nozzle is an accessory of the blower and i[...]

  • Page 18

    16 – English USING THE BLOWER 1. Open the collection bag. Insert the collection bag tube from inside the bag to fit in the vacuum inlet opening of the bag as illustrated in the adjacent figure. Close the zipper on the bag. 2. Press the collection bag tube on the blower, turn it 1/4 of a turn until a snap is heard. The section of the tube that is [...]

  • Page 19

    English – 17 USING THE BLOWER ! WARNING! Do not operate the blower while standing on a ladder or a stand. When operating the blower , the blower and collection bag must be secured in the shoulder strap. The strap should be worn over the shoulder as shown in the adjacent figure. WARNING! Always check that the collection bag is intact and the zippe[...]

  • Page 20

    18 – English MAINTENANCE The fuel quantity required in relation to the air flow , provided by the opening in the throttle, is adjusted by the L and H jets. If they are screwed clockwise, the air/fuel mixture becomes leaner (less fuel) and if they are screwed counterclockwise, the mixture becomes richer (more fuel). A leaner mixture gives rise to [...]

  • Page 21

    English – 19 MAINTENANCE Muffler NOTE! Some mufflers are fitted with a catalytic converter . See “T echnical data” to see whether you clearing saw is fitted with a catalytic converter . The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user . The exhaust fumes are hot and can contain sparks, which[...]

  • Page 22

    20 – English The air filter (A) must be cleaned regularly to remove dust and dirt. This will prevent: • Carburetor malfunctions • Starting problems • Reduced performance • Unnecessary wear on engine parts • Abnormal fuel consumption • Elevated content of harmful exhaust fumes Clean the filter after 25 hours of operation or more often [...]

  • Page 23

    English – 21 MAINTENANCE Starter device T o change a broken or worn cord 1. Unscrew the screws (A) to remove the starter device from the blower . 2. Pull out the cord approx. 30 cm (12”) and lift it up into the notch in the periphery of the pulley . 3. Rotate the pulley counterclockwise until the recoil spring is no longer tensioned. 4. Unscrew[...]

  • Page 24

    22 – English MAINTENANCE T o change the recoil spring 1. Dismantle the pulley according to items 1 to 5 in the instructions on the preceding page. WARNING! The recoil spring may pop out and cause injury. Wear protective goggles or a visor. ! 2. Carefully lift out the recoil spring. 3. Fit the new recoil spring held together by a wire or holder , [...]

  • Page 25

    English – 23 MAINTENANCE 1 2+3 4 5 8 1+3 4 5 6 7 8 2 Maintenance schedule A number of general maintenance instructions are given below . If more detailed instructions are required, get in touch with your local servicing dealer . Daily maintenance 1. Clean the exterior surfaces of the blower . 2. Check that the throttle lock and the throttle trig-[...]

  • Page 26

    24 – English MAINTENANCE Monthly maintenance 1. Flush the fuel tank with clean gasoline, which afterward should be disposed of in an environ- mentally correct manner . 2. Clean the outside of the carburetor and the space around it. Replace damaged parts. 3. Clean the fan blades on the flywheel and the space around it. 4. Check the fuel filter and[...]

  • Page 27

    English – 25 TECHNICAL DA T A 25,4 34 28 3.000 8.200 7.400 0.9 kW/9000 rpm Ye s W albro MB/CD Champion RCJ 7Y 0.5 W albro/WT 0.4 5.1 92 102 2.6 4.2 Radial fan 57 (206) 425 665 560 Engine Cylinder volume, cm 3 : Cylinder bore, mm: Stroke, mm: Idling speed, rpm: Max. speed – blowing, rpm: Max. speed – vacuuming, rpm: Max. engine output to ISO 8[...]

  • Page 28

    EMISSION CONTROL W ARRANTY ST A TEMENT YOUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 1999 and later small nonroad engine. In U.S., new small nonroad engines must be designed, built and [...]

  • Page 29

    Svenska – 31 Sve-5 225/232/235 Bruk 97-11-25, 08.46 31[...]

  • Page 30

    Svenska – 31 Sve-5 225/232/235 Bruk 97-11-25, 08.46 31[...]

  • Page 31

    Svenska – 31 Sve-5 225/232/235 Bruk 97-11-25, 08.46 31[...]

  • Page 32

    2000W01[...]