Français dropdown-ico

Husqvarna 445 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Husqvarna 445. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Husqvarna 445 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Husqvarna 445 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Husqvarna 445 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Husqvarna 445
- nom du fabricant et année de fabrication Husqvarna 445
- instructions d'utilisation, de réglage et d’entretien de l'équipement Husqvarna 445
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Husqvarna 445 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Husqvarna 445 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Husqvarna en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Husqvarna 445, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Husqvarna 445, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Husqvarna 445. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h 115 10 81-26 Re v .2 2008-01-11 445 445e 450e Oper ator ′ s manual Please r ead the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.[...]

  • Page 2

    KEY T O SYMBOLS 2 – English 115 10 81-26 Re v .2 2008-01-11 Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine. Alwa ys wear [...]

  • Page 3

    CONTENTS English – 3 115 10 81-26 Re v .2 2008-01-11 Contents KEY T O SYMBOLS Symbols on the machine: 2 Symbols in the operator’ s manual: 2 CONTENTS Contents 3 INTR ODUCTION Dear Customer , 4 WHA T IS WHA T? What is what on the chain sa w? 5 GENERAL SAFETY PRECA UTIONS Bef ore using a new chain sa w 6 Impor tant 6 Alwa ys use common sense 7 P [...]

  • Page 4

    4 – English INTR ODUCTION 115 10 81-26 Re v .2 2008-01-11 Dear Customer , Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River , for production of muskets . The location was log[...]

  • Page 5

    English – 5 WHA T IS WHA T? 115 10 81-26 Re v .2 2008-01-11 What is what on the c hain saw? 1 Cylinder cov er 2 Decompression valv e 3 Air purge 4 Star t reminder 5 Combined star t and stop switch 6 Rear handle 7 Information and warning decal 8 Fuel tank 9 Adjuster screws carb urettor 10 Star ter handle 11 Star ter 12 Chain oil tank 13 Product an[...]

  • Page 6

    GENERAL SAFETY PRECA UTIONS 6 – English 115 10 81-26 Re v .2 2008-01-11 Bef ore using a new c hain saw • Please read this manual carefully . • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly . • Refuel and star t the chain saw . See the instructions under the headings Fuel Hand[...]

  • Page 7

    GENERAL SAFETY PRECA UTIONS English – 7 115 10 81-26 Re v .2 2008-01-11 Al ways use common sense It is not possib le to cov er every conceivab le situation you can face when using a chain sa w . Always e xercise care and use your common sense . A void all situations which y ou consider to be bey ond your capability . If you still feel uncer tain [...]

  • Page 8

    GENERAL SAFETY PRECA UTIONS 8 – English 115 10 81-26 Re v .2 2008-01-11 • The chain brake (A) can either be activ ated manually (by y our left hand) or automatically by the iner tia release mechanism. • The brake is applied when the front hand guard (B) is pushed forw ards. • This mov ement activates a spring-loaded mechanism that tightens [...]

  • Page 9

    GENERAL SAFETY PRECA UTIONS English – 9 115 10 81-26 Re v .2 2008-01-11 If the kickbac k is less violent or the kickback zone of the bar is closer to you the chain brak e will be activated manually b y the movement of y our left hand. • In the felling position the left hand is in a position that makes manual activ ation of the chain brake impos[...]

  • Page 10

    GENERAL SAFETY PRECA UTIONS 10 – English 115 10 81-26 Re v .2 2008-01-11 Right hand guar d Apar t from protecting your hand if the chain jumps or snaps, the right hand guard stops branches and twigs from interfering with your g r ip on the rear handle. Vibration damping system Y our machine is equipped with a vibration damping system that is desi[...]

  • Page 11

    GENERAL SAFETY PRECA UTIONS English – 11 115 10 81-26 Re v .2 2008-01-11 Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of kickback. • Reduce the risk of the saw chain breaking or jumping off the bar . • Obtain optimal cutting performance. • Extend the life of cutt[...]

  • Page 12

    GENERAL SAFETY PRECA UTIONS 12 – English 115 10 81-26 Re v .2 2008-01-11 • Number of drive links. The number of driv e links is determined by the length of the bar , the chain pitch and the number of teeth on the bar tip sprock et. • Bar groov e width (inches/mm). The groo ve in the bar must match the width of the chain drive links. • Chain[...]

  • Page 13

    GENERAL SAFETY PRECA UTIONS English – 13 115 10 81-26 Re v .2 2008-01-11 Sharpening cutting teeth T o sharpen cutting teeth you will need a round file and a file gauge. See instructions under the heading T echnical data for inf ormation on the size of file and gauge that are recommended for the chain fitted to y our chain saw . • Check that[...]

  • Page 14

    GENERAL SAFETY PRECA UTIONS 14 – English 115 10 81-26 Re v .2 2008-01-11 445 • Loosen the bar nut that holds the clutch cov er and chain brake . Use the combination spanner. Then retighten the bar nut as tightly as you can b y hand. • Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination[...]

  • Page 15

    GENERAL SAFETY PRECA UTIONS English – 15 115 10 81-26 Re v .2 2008-01-11 Lubricating cutting equipment Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather . As a chain saw manuf acturer we hav e developed an optimal chain oil whi[...]

  • Page 16

    GENERAL SAFETY PRECA UTIONS 16 – English 115 10 81-26 Re v .2 2008-01-11 Chain drive sproc ket The clutch drum is fitted with one of the follo wing dr ive sprock ets: A Spur sprock et (the chain sprocket is welded on the drum) B Rim sprock et (replaceable) Regularly check the degree of wear on the drive sproc ket. Replace if wear is e xcessive. [...]

  • Page 17

    ASSEMBL Y English – 17 115 10 81-26 Re v .2 2008-01-11 Fitting the bar and chain 445 Check that the chain brak e is in disengaged position by moving the front hand guard tow ards the front handle. Remov e the bar nuts and remove the clutch co ver (chain brake). T ak e off the transpor tation ring (A). Fit the bar ov er the bar bolts. Place the ba[...]

  • Page 18

    ASSEMBL Y 18 – English 115 10 81-26 Re v .2 2008-01-11 Fit the bar ov er the bar bolts. Place the bar in its rear most position. Place the chain over the driv e sprocket locate it in the groov e on the bar. Begin on the top edge of the bar. Make sure that the edges of the cutting links are f acing forw ard on the top edge of the bar. Fit the clut[...]

  • Page 19

    FUEL HANDLING English – 19 115 10 81-26 Re v .2 2008-01-11 Fuel Note! The machine is equipped with a two-stroke engine and must alwa ys be run using a mixture of petrol and two- stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, ev en s[...]

  • Page 20

    FUEL HANDLING 20 – English 115 10 81-26 Re v .2 2008-01-11 Fuelling Clean the area around the fuel cap . Clean the fuel and chain oil tanks regularly . The fuel filter must be replaced at least once a year . Contamination in the tanks causes malfunction. Make sure the fuel is well mix ed by shaking the container before refuelling. The capacities[...]

  • Page 21

    ST AR TING AND ST OPPING English – 21 115 10 81-26 Re v .2 2008-01-11 Starting and stopping Starting The chain brak e must be engaged when the chain saw is star ted. Activate the brak e by moving the front hand guard forw ards. Cold engine Start position (1): Set the star t/stop switch in the chok e position by pulling the red control outward - u[...]

  • Page 22

    ST AR TING AND ST OPPING 22 – English 115 10 81-26 Re v .2 2008-01-11 Note! Reactivate the chain brake b y pushing the front hand guard bac k towards the front handle. The chain saw is now ready f or use. • Nev er star t a chain saw unless the bar , chain and all cov ers are fitted correctly . See instructions under the heading Assembly . With[...]

  • Page 23

    W ORKING TECHNIQUES English – 23 115 10 81-26 Re v .2 2008-01-11 Bef ore use: 1 Check that the chain brak e works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle loc kout works correctly and is not damaged. 4 Check that the stop s witch works correctly and is not damaged. 5 Check that[...]

  • Page 24

    W ORKING TECHNIQUES 24 – English 115 10 81-26 Re v .2 2008-01-11 6 Before mo ving your chain saw s witch off the engine and lock the chain using the chain brak e. Carr y the chain saw with the bar and chain pointing bac kwards. Fit a guard to the bar before tr anspor ting the chain saw or carrying it for any distance . 7 When you put the chain sa[...]

  • Page 25

    W ORKING TECHNIQUES English – 25 115 10 81-26 Re v .2 2008-01-11 7 T ake great care when y ou cut with the top edge of the bar , i.e. when cutting from the underside of the object. This is known as cutting on the push stroke . The chain tries to push the chain saw back to wards the user . If the saw chain is jamming, the sa w may be pushed back a[...]

  • Page 26

    W ORKING TECHNIQUES 26 – English 115 10 81-26 Re v .2 2008-01-11 Limbing When limbing thick br anches you should use the same approach as for cutting. Cut difficult branches piece by piece . Cutting If you ha ve a pile of logs, each log you attempt to cut should be remov ed from the pile, placed on a saw horse or runners and cut individually . R[...]

  • Page 27

    W ORKING TECHNIQUES English – 27 115 10 81-26 Re v .2 2008-01-11 Felling direction The aim is to f ell the tree in a position where you can limb and cross-cut the log as easily as possible. Y ou want it to fall in a location where y ou can stand and move about safely . Once you ha ve decided which wa y you want the tree to f all you must judge wh[...]

  • Page 28

    W ORKING TECHNIQUES 28 – English 115 10 81-26 Re v .2 2008-01-11 Ne xt mak e the bottom cut so that it finishes exactly at the end of the top cut. The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45 ° . The line where the two cuts meet is called the directional cut [...]

  • Page 29

    W ORKING TECHNIQUES English – 29 115 10 81-26 Re v .2 2008-01-11 Freeing a tree that has fallen badl y Freeing a ”trapped tree” It is very dangerous to remov e a trapped tree and there is high accident risk. Nev er tr y to fell the tree that is tr apped. Nev er work in the risk zone of the hanging trapped tree. The safest method is to use a w[...]

  • Page 30

    W ORKING TECHNIQUES 30 – English 115 10 81-26 Re v .2 2008-01-11 Kickbac k always occurs in the cutting plane of the bar . Normally the chain saw and bar are thrown backw ards and upwards tow ards the user. Howev er, the chain sa w may mo ve in a different direction depending on the w ay it was being used when the kickbac k zone of the bar touche[...]

  • Page 31

    MAINTENANCE English – 31 115 10 81-26 Re v .2 2008-01-11 General The user must only carry out the maintenance and service work descr ibed in this Operator’ s Manual. More extensiv e work must be carried out by an authorised service workshop. Carburettor adjustment Y our Husqvarna product has been designed and manuf actured to specifications th[...]

  • Page 32

    MAINTENANCE 32 – English 115 10 81-26 Re v .2 2008-01-11 Checking the inertia brake release Place the chain saw , with the engine switched off, on a stump or other stable surf ace. Release the front handle and let the saw f all by its own weight, rotating around the rear handle towards the stump . When the bar hits the stump the brake should be a[...]

  • Page 33

    MAINTENANCE English – 33 115 10 81-26 Re v .2 2008-01-11 Chain catcher Chec k that the chain catcher is not damaged and is firmly attached to the body of the chain saw . Right hand guar d Chec k that the right hand guard is not damaged and that there are no visible def ects, such as cracks . Vibration damping system Regular ly check the vibratio[...]

  • Page 34

    MAINTENANCE 34 – English 115 10 81-26 Re v .2 2008-01-11 use a muffler if the spark arrestor mesh is missing or defective. The muffler is designed to reduce the noise le vel and to direct the exhaust gases a way from the oper ator. The exhaust gases are hot and can contain sparks, which ma y cause fire if directed against dry and combustible m[...]

  • Page 35

    MAINTENANCE English – 35 115 10 81-26 Re v .2 2008-01-11 Replacing the return and drive springs Recoil spring (A) • Lift up the star ter pulley . See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the star ter housing. • Remov e the cassette with the recoil spr[...]

  • Page 36

    MAINTENANCE 36 – English 115 10 81-26 Re v .2 2008-01-11 Spark plug The spark plug condition is influenced by: • Incorrect carburettor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dir ty air filter . These factors cause deposits on the spark plug electrodes, which ma y result in operating problems and s[...]

  • Page 37

    MAINTENANCE English – 37 115 10 81-26 Re v .2 2008-01-11 ”Air Injection” centrifugal cleaning Centrifugal cleaning means the following: All air to the carburettor passes through the starter. Dir t and dust is centrifuged out by the cooling fan. IMPORT ANT! In order to maintain operation of the centrifugal cleaning system it must be regularly [...]

  • Page 38

    38 – English MAINTENANCE 115 10 81-26 Re v .2 2008-01-11 Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Weekl y maintenance Monthly maintenance Clean the outside of the machine. On chain saws without a catalytic c[...]

  • Page 39

    English – 39 TECHNICAL D A T A 115 10 81-26 Re v .2 2008-01-11 T echnical data Note 1: Noise emissions in the en vironment measured as sound pow er (L W A ) in conf or mity with EC directiv e 2000/14/EC. Note 2: Equivalent sound pressure le vel, according to ISO 22868, is calculated as the time-weighted energy total for noise pressure lev els und[...]

  • Page 40

    40 – English TECHNICAL D A T A 115 10 81-26 Re v .2 2008-01-11 Bar and chain combinations The follo wing combinations are CE approved. Sa w c hain filing and file gaug es Bar Chain Length, inch Pitch, inch Gauge, mm Max. nose radius T ype Length, drive links (no.) 13 0,325 1,3 10T Husqvarna H30 56 15 0,325 10T 64 16 0,325 10T 66 18 0,325 10T 72[...]

  • Page 41

    English – 41 TECHNICAL D A T A 115 10 81-26 Re v .2 2008-01-11 EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-561 82 Huskv ar na, Sweden, tel: +46-36-146500, declares under sole responsibility that the chain saws Husqv arna 445, 445e and 450e from 2007’ s serial numbers and onwards (the y ear is clear ly stated in pla[...]

  • Page 42

    ´®z+S(,¶6c¨ ´®z+S(,¶6c¨ 115 10 81-26 Re v .2 2008-01-11[...]

  • Page 43

    [...]

  • Page 44

    1151081-26 ´®z+S(,¶6c¨ ´®z+S(,¶6c¨ 2008-01-11 115 10 81-26 Re v .2 2008-01-11[...]