Français dropdown-ico

Husqvarna 965167936 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Husqvarna 965167936. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Husqvarna 965167936 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Husqvarna 965167936 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Husqvarna 965167936 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Husqvarna 965167936
- nom du fabricant et année de fabrication Husqvarna 965167936
- instructions d'utilisation, de réglage et d’entretien de l'équipement Husqvarna 965167936
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Husqvarna 965167936 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Husqvarna 965167936 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Husqvarna en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Husqvarna 965167936, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Husqvarna 965167936, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Husqvarna 965167936. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h 115 10 82-26 Re v .2 2008-06-03 435 435e 440e Oper ator ′ s manual Please r ead the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.[...]

  • Page 2

    KEY T O SYMBOLS 2 – English 115 10 82-26 Re v .2 2008-06-03 Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine. Alwa ys wear [...]

  • Page 3

    CONTENTS English – 3 115 10 82-26 Re v .2 2008-06-03 Contents KEY T O SYMBOLS Symbols on the machine: ..................................... 2 Symbols in the operator’ s manual: ....................... 2 CONTENTS Contents ............................................................... 3 INTR ODUCTION Dear Customer , .............................[...]

  • Page 4

    4 – English INTR ODUCTION 115 10 82-26 Re v .2 2008-06-03 Dear Customer , Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River , for production of muskets . The location was log[...]

  • Page 5

    English – 5 WHA T IS WHA T? 115 10 82-26 Re v .2 2008-06-03 What is what on the c hain saw? 1 Cylinder cov er 2 Air purge 3 Star t reminder 4 Combined star t and stop switch 5 Rear handle 6 Information and warning decal 7 Fuel tank 8 Adjuster screws carb urettor 9 Star ter handle 10 Star ter 11 Chain oil tank 12 Product and serial number plate 13[...]

  • Page 6

    GENERAL SAFETY PRECA UTIONS 6 – English 115 10 82-26 Re v .2 2008-06-03 Bef ore using a new c hain saw • Please read this manual carefully . • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly . • Refuel and star t the chain saw . See the instructions under the headings Fuel Hand[...]

  • Page 7

    GENERAL SAFETY PRECA UTIONS English – 7 115 10 82-26 Re v .2 2008-06-03 Al ways use common sense It is not possib le to cov er every conceivab le situation you can face when using a chain sa w . Alw ays e xercise care and use your common sense. Av oid all situations which you consider to be be yond your capability . If you still feel uncer tain a[...]

  • Page 8

    GENERAL SAFETY PRECA UTIONS 8 – English 115 10 82-26 Re v .2 2008-06-03 T ake care when using y our saw and make sure the kickbac k zone of the bar nev er touches any object. • The chain brake (A) can either be activ ated manually (by y our left hand) or automatically by the iner tia release mechanism. • The brake is applied when the front ha[...]

  • Page 9

    GENERAL SAFETY PRECA UTIONS English – 9 115 10 82-26 Re v .2 2008-06-03 If the kickbac k is less violent or the kickback zone of the bar is closer to you the chain brak e will be activated manually b y the movement of y our left hand. • In the felling position the left hand is in a position that makes manual activ ation of the chain brake impos[...]

  • Page 10

    GENERAL SAFETY PRECA UTIONS 10 – English 115 10 82-26 Re v .2 2008-06-03 Right hand guard Apar t from protecting your hand if the chain jumps or snaps, the right hand guard stops branches and twigs from interfering with your g r ip on the rear handle. Vibration damping system Y our machine is equipped with a vibration damping system that is desig[...]

  • Page 11

    GENERAL SAFETY PRECA UTIONS English – 11 115 10 82-26 Re v .2 2008-06-03 Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of kickback. • Reduce the risk of the saw chain breaking or jumping off the bar . • Obtain optimal cutting performance. • Extend the life of cutt[...]

  • Page 12

    GENERAL SAFETY PRECA UTIONS 12 – English 115 10 82-26 Re v .2 2008-06-03 • Number of drive links. The number of driv e links is determined by the length of the bar , the chain pitch and the number of teeth on the bar tip sprock et. • Bar groov e width (inches/mm). The groo ve in the bar must match the width of the chain drive links. • Chain[...]

  • Page 13

    GENERAL SAFETY PRECA UTIONS English – 13 115 10 82-26 Re v .2 2008-06-03 Sharpening cutting teeth T o sharpen cutting teeth you will need a round file and a file gauge. See instructions under the heading T echnical data for inf ormation on the size of file and gauge that are recommended for the chain fitted to y our chain saw . • Check that[...]

  • Page 14

    GENERAL SAFETY PRECA UTIONS 14 – English 115 10 82-26 Re v .2 2008-06-03 T ension the chain as tightly as possible, b ut not so tight that you cannot pull it round freely b y hand. 435 • Loosen the bar nut that holds the clutch cov er and chain brake . Use the combination spanner. Then retighten the bar nut as tightly as you can b y hand. • R[...]

  • Page 15

    GENERAL SAFETY PRECA UTIONS English – 15 115 10 82-26 Re v .2 2008-06-03 • Fold the knob bac k in to lock the tensioning. Lubricating cutting equipment Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather . As a chain saw manuf [...]

  • Page 16

    GENERAL SAFETY PRECA UTIONS 16 – English 115 10 82-26 Re v .2 2008-06-03 Chain drive spr oc ket The clutch drum is fitted with one of the following driv e sprock ets: A Spur sprock et (the chain sprocket is welded on the drum) B Rim sprock et (replaceable) Regularly check the degree of wear on the drive sproc ket. Replace if wear is e xcessive. [...]

  • Page 17

    ASSEMBL Y English – 17 115 10 82-26 Re v .2 2008-06-03 Fitting the bar and chain 435 Chec k that the chain brak e is in disengaged position by moving the front hand guard tow ards the front handle. Unscrew the bar nut and remo ve the clutch cov er (chain brake). T ak e off the transpor tation ring (A). Fit the bar ov er the bar bolt. Place the ba[...]

  • Page 18

    ASSEMBL Y 18 – English 115 10 82-26 Re v .2 2008-06-03 Mount the clutch cov er and remember to fit the chain adjuster pin in the hole in the bar . Check that the drive links of the chain fit correctly ov er the dr ive sproc ket and that the chain is correctly located in the groov e in the bar. T ension the chain by turning the wheel down (+). T[...]

  • Page 19

    FUEL HANDLING English – 19 115 10 82-26 Re v .2 2008-06-03 Fuel Note! The machine is equipped with a two-stroke engine and must alwa ys be run using a mixture of petrol and two- stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, ev en s[...]

  • Page 20

    FUEL HANDLING 20 – English 115 10 82-26 Re v .2 2008-06-03 Fuelling Clean the area around the fuel cap . Clean the fuel and chain oil tanks regularly . The fuel filter must be replaced at least once a year . Contamination in the tanks causes malfunction. Make sure the fuel is well mix ed by shaking the container before refuelling. The capacities[...]

  • Page 21

    ST AR TING AND ST OPPING English – 21 115 10 82-26 Re v .2 2008-06-03 Star ting and stopping Starting The chain brake m ust be engaged when the chain saw is star ted. Activate the brak e by moving the front hand guard forw ards. Cold engine Star t position (1): Set the star t/stop switch in the choke position by pulling the red control outward - [...]

  • Page 22

    ST AR TING AND ST OPPING 22 – English 115 10 82-26 Re v .2 2008-06-03 • Nev er star t a chain saw unless the bar , chain and all cov ers are fitted correctly . See instructions under the heading Assembly . Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injur y . • The chain brake should be activ[...]

  • Page 23

    WORKING TECHNIQUES English – 23 115 10 82-26 Re v .2 2008-06-03 Bef ore use: 1 Check that the chain brak e works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle loc kout works correctly and is not damaged. 4 Check that the stop s witch works correctly and is not damaged. 5 Check that [...]

  • Page 24

    WORKING TECHNIQUES 24 – English 115 10 82-26 Re v .2 2008-06-03 6 Before mo ving your chain saw s witch off the engine and lock the chain using the chain brak e. Carr y the chain saw with the bar and chain pointing bac kwards. Fit a guard to the bar before tr anspor ting the chain saw or carrying it for any distance . 7 When you put the chain sa [...]

  • Page 25

    WORKING TECHNIQUES English – 25 115 10 82-26 Re v .2 2008-06-03 the sa w chain is jamming, the sa w may be pushed back at y ou. 8 Unless the user resists this pushing force there is a risk that the chain saw will mov e so far backw ards that only the kickbac k zone of the bar is in contact with the tree, which will lead to a kickbac k. Cutting wi[...]

  • Page 26

    WORKING TECHNIQUES 26 – English 115 10 82-26 Re v .2 2008-06-03 The f ollo wing instr uctions describe how to handle the commonest situations you are lik ely to encounter when using a chain saw . Limbing When limbing thick branches y ou should use the same approach as for cutting. Cut difficult branches piece by piece . Cutting If y ou ha ve a p[...]

  • Page 27

    WORKING TECHNIQUES English – 27 115 10 82-26 Re v .2 2008-06-03 Felling direction The aim is to fell the tree in a position where y ou can limb and cross-cut the log as easily as possible. Y ou want it to fall in a location where y ou can stand and move about safely . Once you ha ve decided which wa y you want the tree to f all you must judge whi[...]

  • Page 28

    WORKING TECHNIQUES 28 – English 115 10 82-26 Re v .2 2008-06-03 Ne xt mak e the bottom cut so that it finishes exactly at the end of the top cut. The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45 ° . The line where the two cuts meet is called the directional cut l[...]

  • Page 29

    WORKING TECHNIQUES English – 29 115 10 82-26 Re v .2 2008-06-03 Freeing a tree that has fallen badly Freeing a ”trapped tree” It is very dangerous to remov e a trapped tree and there is high accident risk. Nev er tr y to fell the tree that is tr apped. Nev er work in the risk zone of the hanging trapped tree. The safest method is to use a win[...]

  • Page 30

    WORKING TECHNIQUES 30 – English 115 10 82-26 Re v .2 2008-06-03 Ho w to a void kic kback What is kickbac k? The w ord kickbac k is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar , known as the kickbac k zone, touches an object. Kickbac k always occurs in t[...]

  • Page 31

    MAINTENANCE English – 31 115 10 82-26 Re v .2 2008-06-03 General The user must only carry out the maintenance and service work descr ibed in this Operator’ s Manual. More extensiv e work must be carried out by an authorised service workshop. Carb urettor adjustment Y our Husqv ar na product has been designed and manuf actured to specifications[...]

  • Page 32

    MAINTENANCE 32 – English 115 10 82-26 Re v .2 2008-06-03 Chec king the inertia brake release Place the chain saw , with the engine s witched off, on a stump or other stable surf ace. Release the front handle and let the saw f all by its own weight, rotating around the rear handle towards the stump . When the bar hits the stump the brake should be[...]

  • Page 33

    MAINTENANCE English – 33 115 10 82-26 Re v .2 2008-06-03 Right hand guard Chec k that the right hand guard is not damaged and that there are no visible def ects, such as cracks . Vibration damping system Regular ly check the vibration damping units f or cracks or deformation. Make sure the vibration damping units are securely attached to the engi[...]

  • Page 34

    MAINTENANCE 34 – English 115 10 82-26 Re v .2 2008-06-03 Starter Replacing the starter cord • Loosen the screws that hold the starter against the crankcase and remov e the star ter. • Pull out the cord approx. 30 cm and hook it into the notch in the rim of the pulley . Release the recoil spr ing by letting the pulle y rotate slowly backwards [...]

  • Page 35

    MAINTENANCE English – 35 115 10 82-26 Re v .2 2008-06-03 Replacing the return and drive springs Recoil spring (A) • Lift up the star ter pulley . See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the star ter housing. • Remov e the cassette with the recoil spr[...]

  • Page 36

    MAINTENANCE 36 – English 115 10 82-26 Re v .2 2008-06-03 Spark plug The spar k plug condition is influenced by: • Incorrect carburettor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dir ty air filter . These factors cause deposits on the spark plug electrodes, which ma y result in operating problems and [...]

  • Page 37

    MAINTENANCE English – 37 115 10 82-26 Re v .2 2008-06-03 ”Air Injection” centrifugal cleaning Centr ifugal cleaning means the following: All air to the carburettor passes through the starter. Dir t and dust is centrifuged out by the cooling fan. IMPORT ANT! In order to maintain operation of the centrifugal cleaning system it must be regularly[...]

  • Page 38

    38 – English MAINTENANCE 115 10 82-26 Re v .2 2008-06-03 Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Dail y maintenance Weekl y maintenance Monthly maintenance Clean the outside of the machine . On chain saws without a catalytic[...]

  • Page 39

    English – 39 TECHNICAL D A T A 115 10 82-26 Re v .2 2008-06-03 T echnical data Note 1: Noise emissions in the environment measured as sound power (L W A ) in conformity with EC directive 2000/14/EC . Note 2: Equivalent sound pressure le vel, according to ISO 22868, is calculated as the time-weighted energy total for noise pressure lev els under v[...]

  • Page 40

    40 – English TECHNICAL D A T A 115 10 82-26 Re v .2 2008-06-03 Bar and chain combinations The f ollo wing combinations are CE approved. Sa w c hain filing and file gaug es Bar Chain Length, inch Pitch, inch Gauge , mm Max. nose radius T ype Length, drive links (no.) 13 0,325 1,3 10T Husqv arna H30 56 15 0,325 10T 64 16 0,325 10T 66 18 0,325 10T[...]

  • Page 41

    English – 41 TECHNICAL D A T A 115 10 82-26 Re v .2 2008-06-03 EC-dec laration of conf ormity (Applies to Europe onl y) Husqvarna AB , SE-561 82 Huskv ar na, Sweden, tel: +46-36-146500, declares under sole responsibility that the chain saws Husqv arna 435, 435e and 440e from 2008’ s serial numbers and onwards (the year is clearly stated in plai[...]

  • Page 42

    ´®z+S(6¶68¨ ´®z+S(6¶68¨ 115 10 82-26 Re v .2 2008-06-03[...]

  • Page 43

    [...]

  • Page 44

    1151082-26 ´®z+S(6¶68¨ ´®z+S(6¶68¨ 2008-06-03 115 10 82-26 Re v .2 2008-06-03[...]