Husqvarna Viking H Class E 10 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Aller à la page of

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Husqvarna Viking H Class E 10. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Husqvarna Viking H Class E 10 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Husqvarna Viking H Class E 10 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Husqvarna Viking H Class E 10 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Husqvarna Viking H Class E 10
- nom du fabricant et année de fabrication Husqvarna Viking H Class E 10
- instructions d'utilisation, de réglage et d’entretien de l'équipement Husqvarna Viking H Class E 10
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Husqvarna Viking H Class E 10 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Husqvarna Viking H Class E 10 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Husqvarna en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Husqvarna Viking H Class E 10, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Husqvarna Viking H Class E 10, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Husqvarna Viking H Class E 10. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    E10 USER’S GUIDE[...]

  • Page 2

    This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594 IMPORT ANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this household sewing machine. DANGER - T o reduce the risk of electric shock: • A s[...]

  • Page 3

    Congratulations! As the owner of a new sewing machine, you will enjoy precision quality stitching on all types of fabrics, from multiple layers of denim to delicate silks. Y our sewing machine offers the ultimate in simplicity and ease of operation. For your safety and to fully enjoy the many advantages and ease of operation of your sewing machine,[...]

  • Page 4

    4 LIST OF CONTENTS PRINCIP AL P ARTS OF THE MACHINE ....................................................................5 ACCESSORIES......................................................................................................... 7 FITTING THE SNAP-IN ACCESSORY BOX ............................................................. 8 CONNECTING [...]

  • Page 5

    5 PRINCIP AL P ARTS OF THE MACHINE 1. Thread tension dial 2. Presser foot pressure 3. Thread take-up lever 4. Thread cutting 5. Presser foot 6. Needle plate 7. Accessories box 8. Bobbin stop 9. Stitch length dial 10. Stitch display 1 1. Reverse sewing lever[...]

  • Page 6

    6 12. Spool pin 13. Bobbin winder 14. Hole for second spool pin 15. Hand wheel 16. Stitch selector dial 17. Power switch 18. Main plug socket 19. Bobbin thread guide 20. Upper thread guide 21. Handle 22. Presser foot lever[...]

  • Page 7

    7 12 3 4 56 7 89 1 0 1 1 12 14 13 15 ACCESSORIES 1. All purpose foot 2. Zipper foot 3. Satin stitch foot 4. Blind hem foot 5 Buttonhole foot 6. L-screwdriver 7. Seam ripper/ brush 8. Oil bottle 9. Second spool pin 10. Spool holders (2x) 1 1. Pack of needles 12. Seam guide 13. Bobbins (3x) 14. Darning plate 15. Felt pad[...]

  • Page 8

    8 FITTING THE SNAP-IN ACCESSOR Y BOX Keep the snap-in accessory box horizontal, and push it in the direction of the arrow . (1) T o open, lift up at the point of the arrow . (2)[...]

  • Page 9

    9 1 3 CONNECTING THE MACHINE TO POWER SOURCE Connect the machine to a power source as illustrated. (1) A polarized plug must be used with the appropriate polarized outlet. (2) Attention: Unplug power cord when machine is not in use. Foot control Foot control regulates the sewing speed. (3) Attention: Consult a quali ¿ ed electrician if in doubt as[...]

  • Page 10

    10 CHANGING THE BULB Attention: Disconnect the machine from the power supply by removing the plug from the main socket! Replace bulb with same type rated 10 watts (1 10-120V) or 15 watts (220-240V). - Loosen screw (A) as illustrated. (1) - Remove the cover (B). - Unscrew the bulb and ¿ t new one (C). (2) - Replace the cover and tighten screw . Sho[...]

  • Page 11

    11 + - TWO-STEP PRESSER FOOT LEVER When sewing several layers or thick fabrics, the presser foot can be raised to extra high for easy positioning of the work. (A) The presser foot pressure of the machine has been pre-set and usually requires no readjustment for most fabrics (light-or-heavy weight). However , if you need to adjust the presser foot p[...]

  • Page 12

    12 A TT ACHING THE PRESSER FOOT SHANK/ ANKLE Attaching the presser foot holder Raise the presser foot bar (a). (1) Attach the presser foot shank/ankle (b) as illustrated. Attaching the presser foot Lower the presser foot shank/ankle (b) until the cut-out (c) is directly above the pin on the foot (d). (2) Raise the lever (e). Lower the presser foot [...]

  • Page 13

    13 WINDING THE BOBBIN Place thread and spool holder onto spool pin (1). - For smaller spools of thread place spool holder with small side next to spool (2). - Wind thread clockwise around bobbin winder tension discs (3). - Thread bobbin as illustrated and place on spindle (4). - Push bobbin to right (5). - Hold thread end (6). - Step on foot contro[...]

  • Page 14

    14 INSERTING THE BOBBIN When inserting or removing the bobbin, the foot and needle must be fully raised. 1. Open the hinged cover . 2. Hold the bobbin case with one hand. Insert the bobbin so that the thread runs in a clockwise direction (arrow). 3. Put the thread under the tension spring. 4. Hold the bobbin case by the hinged latch. 5. Insert it i[...]

  • Page 15

    15 INSERTING THE NEEDLE Change the needle regularly , especially if it is showing signs of wear and causing problems. Insert the needle following the illustrated instructions. A. Loosen the needle clamp screw and tighten again after inserting the new needle. (1) B. The À at side of the needle shaft should be towards the back. C/D.Insert the needle[...]

  • Page 16

    16 THREADING THE UPPER THREAD Threading is simple but it is important to thread correctly to prevent sewing problems could result. - Start by raising the needle to its highest point (1), and also raise the presser foot to release the tension discs. (2) Attention: For safety , it is strongly suggested you turn off the power before threading. - Lift [...]

  • Page 17

    17 THREAD TENSION Basic thread tension setting: “4” T o increase the tension, turn the dial to the next number up. T o reduce the tension, turn the dial to the next number down. A. Normal thread tension - upper and bobbin thread join in fabric B. Upper thread tension too loose - upper thread “loops” on the underside of fabric C. Upper threa[...]

  • Page 18

    18 BRINGING UP THE BOBBIN THREAD Hold the upper thread with the left hand. T urn the handwheel towards you until the needle is raised. (1) Pull on the upper thread to bring the bobbin thread up through the stitch plate hole. Place both threads to the back under the presser foot. (2)[...]

  • Page 19

    19 REVERSE SEWING At the end of a seam, press down the reverse sewing lever . Sew a few reverse stitches to “the tie off” the thread ends. Release the lever and the machine will sew forwards again. (1/A) REMOVING THE F ABRIC T urn the handwheel toward you to bring the thread take up lever to its highest position, raise the presser foot and remo[...]

  • Page 20

    20 MA TCHING NEEDLE / F ABRIC / THREAD NEEDLE, F ABRIC SELECTION NEEDLE SIZE F ABRICS THREAD 9-1 1(65-75) Lightweight fabrics-thin cottons, voile, silk , muslin, interlocks, cotton knits, tricots, jerseys, crepes, woven polyester , shirt & blouse fabrics. Light-duty thread in cotton, nylon or polyester . 12(80) Medium weight fabrics-cotton, sat[...]

  • Page 21

    21 STRAIGHT STITCHING Straight stitching center needle position T urn the stitch selector dial so that the “A” appears in the stitch display window . Snap on the standard presser foot. Adjust the stitch length by turning the stitch length dial to the desired stitch length. 2.5 is standard stitch length. T o get the reinforced triple straight st[...]

  • Page 22

    22 ZIGZAG STITCHING T urn the stitch selector dial so that the stitch display shows “C”-zig- zag. T urning the stitch selector dial will increase or decrease the zig zag width. Snap on the standard foot. Function of stitch length dial while zigzaging The density of zigzag stitches increase as the setting of stitch length dial approaches “0”[...]

  • Page 23

    23 HOW TO SEW BUTT ONHOLES Preparation Select buttonhole with the stitch Selection dial. Snap on The buttonhole foot. Adjust the stitch length dial between “0.5” - “1”. The density of the stitch depends on thickness of the fabric. Note: Always test sew a buttonhole. T o prepare the fabric Measure the diameter of the button and add 0.3 cm (1[...]

  • Page 24

    24 Tips - Slightly reduce upper thread tension to produce a satin stitch on top. - Place stabilizer underneath for ¿ ne and stretchy fabrics. - It is best to sew a cord for a buttonhole on a stretch or knit fabrics. The buttonhole colomns should sew over the cord. (5)[...]

  • Page 25

    25 BLIND HEM For hems, curtains, trousers, skirts, etc. Select Blind hem for stretch fabrics. Select Blind hem for woven fabrics. Snap on Blind hem foot. (1) Stitch length 1.5-2.5 Note: It takes practice to sew blind hems. Always make a sewing test ¿ rst. Fold the fabric as illustrated with the wrong side up. (2) Place the fabric under the foot. T[...]

  • Page 26

    26 ZIPPERS AND PIPING Set the machine as illustrated. (1) The zipper foot can be snapped onto the right or left, depending on which side of the foot you are going to place against the zipper or piping. (2) T o sew past the zipper pull, lower the needle into the fabric, raise the presser foot and push the zipper pull behind the presser foot. Lower t[...]

  • Page 27

    27 3-STEP ZIG-ZAG Sewing on lace and elastic, darning, mending, ¿ nishing edges. Set the machine as illustrated. (1) Patching: Place the patch in position and stitch around edges. The stitch length can be shortened to produce very close stitches. (A) When mending tears, it is advisable to use a piece of backing fabric to reinforce. The stitch dens[...]

  • Page 28

    28 STITCH SELECTION T riple straight stitch: (1) For reinforced seams. T urn the stitch length dial to “S1”. The machine sews two stitches forwards and one stitch backwards. This gives triple reinforcement. T riple zig-zag: (2) For hardwearing seams, hems and decorative seams. T urn the stitch length dial to “S1”. T riple zig-zag is suitabl[...]

  • Page 29

    29 Attention: Disconnect the machine from the electricity supply by removing the plug from the main socket. When cleaning the machine, it must always be disconnected from the electricity supply . Remove the stitch plate T urn the handwheel until the needle is fully raised. Open the hinged front cover and unscrew the needle plate screw withe the scr[...]

  • Page 30

    30 TROUBLE SHOOTING GUIDE Problem Cause Correction Upper thread breaks 1. The machine is not threaded correctly . 2. The thread tension is too tight. 3. The thread is too thick for the needle. 4. The needle is not inserted correctly . 5. The thread is wound around the spool holder pin. 6. The needle is damaged. 1. Rethread the machine. 2. Reduce th[...]

  • Page 31

    Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/electronic products. If in doubt please contact your retailer for guidance[...]

  • Page 32

    VSM Group AB • SE-561 84 Huskvarna • SWEDEN www .husqvarnaviking.com 412 97 80 - 26C • English • Inhouse production • © 2005 VSM Group AB • All statements valid at time of printing • Printed in Sweden on environmental-friendly paper •[...]