Intellinet Network Solutions 523615 manuel d'utilisation

INT-523608/523615-UM-0307-02[...]

2 TABLE OF CONTENTS Section 1: Introduction.... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... ..... .... .... 3 1.1 Warnings .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... ..... .... ..... .... ..... .... . 3 1.2 Package Contents .... ..... .... ..... .... ..... ....[...]

3 4.9.5 NAT On/Off...... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... ..... .... ....49 4.10 Advanced Setup ..... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... ..... .... . 50 4.10.1 Firewall ...... ..... .... ..... ..... .... ..... .... ..... .... ..... .... .....[...]

4 DHCP Server Supported: All of the networked computers can retrieve TCP/IP settings automatically from this device. Static IP Address Binding: Authorizes users to manage and configure a PC in LAN in most cases by binding the MAC address and IP address together. System Log: History of all activity. UPnP: Supports Microsoft’s UPNP (Universal Plug [...]

5 straight-through or cross cable can be used to connect the LAN card or switch. 3. Turn on the power by pressing the power button on the back of the router. The device will perform a self test. During the self test, the PWR LED, CPU/RUN LED and LAN port LEDs of connected ports are lit. After the self test, the CPU/RUN LED starts flashing (on-off-o[...]

6 2.3.2 Model 523615, 8-Port LED Indication PWR Continuously lit indicates power to the router. RUN/CPU Slowly blinking indicates the system is operational after a proper startup. WAN Bli nk ing indi ca tes dat a is being tran smitted t o/fro m the Wi de Area Network. 1–8 Blinking indicates data is being transmitted to/from the Local Area Network[...]

7 directly to Section 4. If you are unable to open the router’s Web Admin screen, follow whichever instructions below apply to the operating system you use. 3.1 Windows 2000 Setup 1. Install the High-Speed Broadband Router. 2. Start Windows 2000 and check whether the LAN LED is on or off. If off, confirm the connection between the computer and th[...]

8 5. Click “Local Area Connection” ➝ “Properties” ➝ “Internet Protocol (TCP/IP)” and “Properties.”[...]

9 6 . C l i c k t h e “ G e n e r a l ” t ab ; se l e ct “ O bt a i n a n I P ad d r e s s a u t o ma t i c al l y ” a n d “ O bt ai n D N S s e r ve r a dd r es s a u t o m at i ca l l y. ” 7. Click “OK.” 8. Click ”Start” ➝ “Run.” 9. Input ”cmd”; then click “OK.” 10. Input “ipconfig” in the pop-up command wind[...]

10 • The IP address is between 192.168.10.2 and 192.168.10.254 • The subnet mask is 255.255.255.0 • The default gateway is 192.168.10.1 (the router’s default IP address) 10. Type “ping 192.168.10.1,” then hit “Enter.” 1 1. I f yo u c a n se e “ R e p l y f r o m 1 9 2. 16 8 . 1 0 . 1 : b y t e s= 3 2 t i m e = 2m s T T L= 6 4 , ?[...]

11 3.2 Windows XP Setup 1. Install the High-Speed Broadband Router. 2. Start Windows XP and check whether the LAN LED is on or off. If off, confirm that the connection between the computer and the router is correct. 3. Click “Start” ➝ “Setting” ➝ “Control Panel.” 4. Double-click “Network and Internet Connections” in “Control P[...]

12[...]

13[...]

14 8. Click “Start” ➝ “Run”; enter “cmd“; click “OK.” 9. Type “ipconfig” in the pop-up command window. NOTE: Make sure the IP information is the same as shown below. • The IP address is between 192.168.10.2 and 192.168.10.254 • The subnet mask is 255.255.255.0 • The default gateway is 192.168.10.1[...]

15 11. Input “ping 192.168.10.1,” then “Enter.” 1 2. I f yo u c a n se e “ R e p l y f r o m 1 9 2. 16 8 . 1 0 . 1 : b y t e s= 3 2 t i m e = 2m s T T L= 6 4 , ” t he n t h e c o nn e c t i on b e t w ee n y o u r c o mp u t e r an d t h e r o u t e r i s co m p l e t e d. 4. ROUTER SETUP 4.1 Start Internet Explorer to Log In 1. Start y[...]

16 Click the “Login” button to enter the configuration and configure the router manually. This may be required if the Internet Wizard fails to detect the settings automatically. The Internet Wizard lets you configure your Internet connection quickly and conveniently. You can login directly without account and password confirmation because there[...]

17 3. Select the “PPPoE User (ADSL)” radio button. 4. Key in the “User ID” and “Password” provided by your Internet service provider. 5. Click the “Apply” button. You will then see the following pop-up window: If “Conn. State” shows “Successfully connected,” the configuration is correct. 6. Click “Show Internet connection [...]

18 If “Conn. Status” is unchanged, check whether your service type is correct. 7. Confirm the WAN connection status: If the WAN connection is successfully established, then by clicking “Show Internet Information” you can enter the WAN status Web page; or click “Status” ➝ “WAN status” and verify the following. • Connection Type s[...]

19 “Connect” is a manual connection button. By clicking it, the system can be connected to the Internet again. Click “Save” to save the current configuration. Restart all PCs connected to the router. NOTE: Save the router configuration after completion; otherwise, the configuration will be lost after the router is restarted. Other configura[...]

20 On Demand is only effective for Disconnect PPP session if idle time is longer than _ Min . Connect Manually: With this option, users have to connect with the Internet manually after disconnection. This option is only effective with Disconnect PPP session if idle time is longer than _ Min . Prevent reconnection although no response from PPP serve[...]

21 6. If Conn. State remains as “Connecting to Internet,” do the following: • Close the pop-up window. • Turn the cable modem power off then on, and check the WAN LED status. 7. Re-click the “Apply” button. 8. Check the WAN Connection Status: If the status is “Successfully connected,” click “Show Internet Information” to enter t[...]

22 The “Connect” button is a manual WAN port IP address refresh function button. If clicked, the WAN port will re-obtain a dynamic IP address and connect with the Internet. Click the “Save” button to save the current configuration, then restart all PCs connected with router. Other configuration options: Physical address Clone: If you want t[...]

23 3. Input WAN IP Address, Subnet Mask, Default Gateway, Primary DNS Server and Secondary DNS Server as provided by your ISP. 4. Click “Apply” to complete. You will see the following pop-up window: 5. Check WAN Conn. State by clicking “Show Internet Information” or click on “Status” ➝ “WAN status.”[...]

24 If the WAN connection is successfully established, you can see the following: • Connection Type should be “Static IP” • Connection Status should be “Successfully connected” • Physical Address shows the router’s WAN port MAC address (physical address). • WAN IP Address, Subnet Mask, Default Gateway, Primary and Secondary DNS ser[...]

25 This page shows current Internet connection status (WAN port), including Connection Type, Connection Status, WAN IP Address, Subnet Mask, Default Gateway and DNS server. With dynamic IP or PPPoE DSL connections, the “Connect” or “Disconnect” button will be shown on this page. Click the “Connect” button to connect with the Internet; c[...]

26 LAN Information: Shows the router’s current LAN connecting status, DHCP server settings, including MAC address (physical address) of the LAN port, and quantities of IP address handed out to other computers or LAN clients. IP allocated: Overview of all connected computers with IP Address, Physical Address (MAC Address) and the connection type ([...]

27 PPPoE (ADSL), Dynamic IP and Static IP setup procedures are illustrated in sections 4.2, 4.3 and 4.4, respectively. 4.6.2 LAN Setup Click ”Basic Setup” ➝ “ LAN/DHCP Setup.” This page lets you configure the LAN IP settings of the router, along with the DHCP server settings. System IP Setup: This section is for changing the IP router LAN[...]

28 DHCP Server Status: The current status of the DHCP server. DHCP Server Operation: Enable or disable the DHCP server. DHCP IP Pool: The IP address range the router assigns to connected computers. It is 192.168.10.2 – 192.168.10.254 by default. Manual DNS configuration: Manually configure the DNS server the DHCP server assigns to the connected c[...]

29 Internet Access Restriction: You can define the maximum number of clients with access to the Internet at the same time. The default value “0” means that there is no limitation. Enter the value “15” if you wish to make sure that at no time more than 15 PCs connect to the Internet. 4.6.3 Link Setup/Info Click “Basic setup” ➝ ”Link [...]

30 Picture showing 4 Port Version Link information, port speed and port statistics are shown on this page. Link Setup: This section is for changing the link settings. Port: The router’s WAN and LAN ports.[...]

31 Mode: Automatic mode and manual mode on/off. In Manual mode, you can define the connection speed. Auto is the default and recommended mode. Speed: When in Manual mode, you can define the port speed here: either 10 Mbps or 100 Mbps. Apply: Apply current settings. Link Information: This section displays link status. Port: The router’s WAN and LA[...]

32 NOTE: Save the router configuration after completion; otherwise, the configuration will be lost after the router is restarted. 4.6.5 Switch Configuration Click “Basic setup” ➝ ”Switch Config.” Port Mirror: Activate to mirror all Internet traffic to the sniffer port (LAN Port 1). Allow Unicast Packets: Activate this option to allow Unic[...]

33 Login Account Setup: Enter your old ID and password and the new values. Click “Apply” to save the changes. The default Login ID is “root”; the default password is blank (no password). Admin E-Mail Setup: If you want to receive router’s the system log via e-mail, configure e-mail address, SMTP server and authentication information here.[...]

34 4.7.2 Firmware Upgrade Click “System” ➝ “Firmware Upgrade.” Firmware updates may be available from time to time for the router. Before contacting technical support, make sure that you have the latest firmware version installed on the router. Upgrade procedure: 1. Download an updated firmware version from www.intellinet-network.com. 2. [...]

35 4. Click on “Browse” and select the new firmware file. Click “Open.” 5. Click “Upgrade” to start the upgrade process.[...]

36 The Router will restart automatically after the upgrade process is completed. After the upgrade, verify the firmware version. NOTE: The upgrade process takes about 60 seconds. During this time, do not turn off the power; otherwise, router will be damaged. 4.7.3 System Log Click “System” ➝ “System log.” System Log Setup The router keeps[...]

37 4.7.4 Access List Click “System” ➝ “Access List.” Access List With this function you can limit access to the router based on the IP address of the computer. IMPORTANT: When you click "Start" to activate the service, you will see: It is important to click "OK" here to make sure your computer still has access to the r[...]

38 Hostname Setup: Configure the router’s device name used in the network. Config Mgmt/Restart : Config Backup: Back up the configuration data. Config Restore: Restore previously saved the configuration data. Restore Default: Restore the factory default configuration. Restart System: Reboot the router. System Time Setup: For the s cheduler. Confi[...]

39 UPNP Setup: UPnP allows devices to connect seamlessly and to simplify the implementation of networks in the home (data sharing, communications and entertainment) and corporate environments. UPnP achieves this by defining and publishing UPnP device control protocols built upon open, Internet-based communication standards. The term UPnP is derived[...]

40 QoS Basic Setup: QoS stands for “Quality of Service.” It allows the control of Int ern et bandwidth based o n di ffe rent crit e ri a such as IP addr ess, port or appl ication. Using QoS, you can limit the amount of bandwidth for a specific user, or you can guarantee a minimum amount of bandwidth for a specific application; for example, HTTP[...]

41 4.8.3 Application QoS Click “QoS” ➝ “Application QoS.” Define the maximum bandwidth available, or the minimum guaranteed bandwidth for pre-defined applications. Setup Method: Choose the application program; select the operation mode (Max. Limit or Min. Guarantee) and specify the bandwidth throughput value for download and upload. Click[...]

42 4.8.4 Ports QoS Click “QoS” ➝ “Port QoS.” Define the maximum bandwidth available, or the minimum guaranteed bandwidth for TCP or UDP ports and port ranges. Setup Method: Enter the port or port range, select the protocol type, select the operation mode (Max. Limit or Min. Guarantee) and specify the bandwidth throughput value for downloa[...]

43 4.9 NAT 4.9.1 Applications Click “NAT” ➝ ”Applications.” Some programs, such as Internet network games, filesharing programs and Internet phones, need more than one connection. Because of the NAT firewall, some of the programs do not work correctly. The “Applications” function can make those programs work well with the High-Speed B[...]

44 lease IP for the client PC is recommended (Basic Setup ➝ LAN/DHCP). The following list shows all applications and the ports they use: Application Port Bu ddyB ud dy TCP 812, TCP 987 WinAmp Broadcasting TCP 8000 GuruGuru TCP 9292 TCP 9999 NetMeeting TCP 1720 WinMX TCP 6699 UDP 6257 Windows XP/2000 Remote Desktop TCP 3389 UDP 3389 Soribada2 UDP2[...]

45 4.9.2 Internal Server Click “NAT” ➝ “Internal Server.” The NAT firewall protects the computers in the local network from unauthorized access from the Internet. Sometimes, however, it is required to allow access to a local computer; e.g., a local FTP server. The router’s Internal Server function is designed to let you do that. Each in[...]

46 Setup Method: 1. Select the LAN service from the list below: Protocol Server DN S DNS (Domain Name Server) SMTP SMTP (Simple Message Transfer Protocol) POP3 POP3 (Post Office Protocol) HTTP Web Server News News Server FTP FTP File Transfer Server Telnet Telnet Server PPTP VPN (Virtual Private Network) 2. Input the server’s local IP address. Cl[...]

47 4.9.3 Port Forwarding Click “NAT” ➝ ”Port Forwarding.” Port Forwarding functions the same way as Internal Server, but it allows entering ranges of ports instead of single ports only. It also does not limit you to pre-defined services. Instead, you can control the entire TCP/IP port range. Setup Method: Rule Name: Enter a name which bes[...]

48 Internal Port Range: 17997–18003 Click “Add.” Repeat the same steps, but this time with UDP (as Silent Hunter requires both TCP and UDP). After completion, you should have two new rules: NOTES: Save the router configuration after completion; otherwise, the configuration will be lost after the router is restarted. Also, the use of a static [...]

49 Protocol: Select the trigger port’s protocol (TCP/UDP). Port Range: Trigger port’s range. Port Forward: Set up the forward port. Protocol: Select the forward port’s protocol (TCP/UDP). Port Range: Forward port’s range. 4.9.5 NAT On/Off Click “ NAT” ➝ “ NAT On/Off.” Use this function to completely disable the NAT function of the[...]

50 4.10 Advanced Setup 4.10.1 Firewall Click “Advanced” ➝ ”Firewall.” The router’s firewall consists of two main functions. 1. Blocking DoS: This function helps to prevent so-called denial-of-service attacks. 2. Connection Filtering: Set of rules to accept or deny data traffic. Blocking DoS: SYN Flooding, Smurf, IP source routing, IP Sp[...]

51 a hacking attempt starts, because the attacker first needs to know if a target is available or not. With this option activated, the router won’t respond to any ping commands sent from the Internet. Blocking ICMP (ping) from LAN to Internet: With this option activated, the router will not transport any outgoing ping command sent by a local stat[...]

52 D y n a m i c D N S ( D D N S ) i s a s y s t e m t h a t a l l o w s t h e d o m a i n na m e d a t a h e l d i n a n a m e s e r v e r t o b e u p d a t e d i n r e a l t i m e . T h e m o s t c o m m o n u s e f o r t h i s i s i n a l l o w i n g a n I n t e r n e t do m a i n n a m e t o b e a s s i g n e d t o a c o m p u t e r ( o r r o u[...]

53 Setup Method: 1. Enter the computer’s name and the LAN card’s MAC address. Then click “Add” to add new rule. You can search for the MAC addresses of all connected computers using the “Search MAC address” button. 2. Clicking on the “Wake-up PC” button sends the Magic Packet to the computer, which causes the computer to start up. 3[...]

54 Setup Method: Status: Current status of the URL filter: “Started” or “Stopped.” Operation: Click “Start” or “Stop” to activate or deactivate the URL filter. IP Address: Enter a single IP address or an IP address range for which this filter should be applied. Physical: Enter the MAC address of the client computer for which this fi[...]

55 you are going to need the functionality. Remote Management should never be enabled if the default administrator password has not been changed. 4.10.6 Scheduler Click “Advanced” ➝ ”Scheduler” as follows: Using this function, you can disable Internet access for a specific computer or range of computers based on the time and day of week. [...]

56 4.10.7 VPN Setup Click “Advanced” ➝ ”VPN Setup.” The device allows five users to establish a VPN tunnel (PPTP) to the router. A VPN tunnel is a secure and encrypted connection between the client and the server. The router supports the PPTP (Point-to-Point Tunneling Protocol) implementation of VPN with optional Microsoft Point-to-Point [...]

57 5. SPECIFICATIONS Standards • IEEE 802 .3 (10Base-T Ethernet) • IEEE 802.3u (100Base-TX Fast Ethernet) General • LAN ports: - Model 523608: 4 RJ-45 10/100 Mbps data ports - Model 523615: 8 RJ-45 10/100 Mbps data ports • LAN ports with Auto MDI/MDI-X • LAN to WAN throughput: 94 Mbps • Flash: 2 MB • Memory: 16 MB SDRAM • Certificat[...]

58 • Certifications: FCC Class B, CE Mark, RoHS LEDs • Power • OP (operational status) • Power Line Link/Act • WAN Link/Act • LAN 1-4/8 Link/Act Environmental • Dimensions: 164 (W) x 108 (L) x 30 (H) mm (6.5 x 4.3 x 1.2 in.) • Weight: 1.0 kg (2.2 lbs.) • Operating temperature: 0 – 55°C (32 – 122°F) • Operating humidity: 10[...]

59[...]

60 www.intellinet-network.com Are you completely satisfied with this product? Please contact your INTELLINET NETWORK SOLUTIONS ™ dealer with comments or questions. SOLUTIONS All products mentioned are trademarks or registered trademarks of their respective owners.[...]