Intellinet 524681 manuel d'utilisation

WIRELESS N 3G ROUTER USER MANUAL MODEL S 524681 & 524940 I N T - 524681 /524940 - UM -08 09 - 03[...]

Federal Communication s Comm ission Interfere nce Sta temen t FCC Part 15 This equi pment has been tested and found t o comply with the limits for a Class B d i gital device, pursuant to Part 15 of FCC Rules. These limits are desi gned to provide reasonable protection against harmful interference in a residential instal lation. This equipment gener[...]

cause harmful interference; and (2) This device must accept any interference re ceived, includ ing interferenc e that may ca use undesi red operation. Any changes or modi fications not expressly appr oved by the part y responsible for compliance could void the autho rity to operate the equipment. Federal Communications Commission (FCC) Radiati on E[...]

R&TTE Compl iance Stat ement This equipment complies wit h all the requirements of Directive 1999/5/E C of the E urop ean Pa rliam ent an d the C ounc il of Marc h 9, 1 999, on radio equipment and telecommunicati on terminal equipment and the mutual recognit ion of their confor mity (R&TTE) . The R&TTE Directi ve repeals a nd replaces i[...]

Table of Contents CHAPTER I: PRODUCT I NFORMA TION 1- 1 Introduction .......................................................................... 1 1- 2 Safety Information ................................................................ . 2 1- 3 System Requirements ........................................................... 3 1- 4 Package Contents ..[...]

2-5-7 Setu p Procedure for Telstra Big P ond ............................. 54 2-5-8 Setu p Procedure for DNS ................................................ 55 2-5-9 Setu p Procedure for DDNS .............................................. 57 2- 6 Wired LAN Configurati on s ................................................... 59 2-6- 1 LAN IP ......[...]

3-4 F ail Over ................................ ............................................ 113 3-5 System Status ................................................................... 115 3-5- 1 System I nformation and F irmware V ersion .................... 115 3-5- 2 Internet Connection Status ............................................ 115 3-5- [...]

1 Chapter I: Product Information 1 - 1 Intr oduction and S afety I nformation Thank you for purcha sing t his INTELLINET NETWORK SOLUTIONS TM Wireles s 300N 3G Rou ter, Model 524681 , or Wirele ss 150 N 3G Ro uter, Model 524940 . T his high - speed wireless 3G broadband router supports both UMTS/ HSDPA a nd EVDO networks. When connecting a 3G / 3.5[...]

2 1 - 2 Safety Information To maintain the safety of users a nd property, fo llow these safety instructions: 1. This device is design ed for indoor u se only; DO NOT place this device outdoor s. 2. DO NOT put this devi ce in or near hot o r humid plac es, like a kitchen or bathroom. Also, do not le ave this device in your car in hot weather . 3. DO[...]

3 1 - 3 System Requirements • Internet conne ction, provided by xDSL or c able modem or 3G m o d e m . • Computer or n etwork device s with wir ed or wirel ess network i n t e r f a c e c a r d . • Web bro wser ( Firefox, Micr osoft I nternet Explorer 4.0 or above, Netscape Navigator 4 .7 or a bove, Opera W eb browser or Safari W e b browser)[...]

4 1 - 5 Connections and Indi cators Front Panel LED Name Light Status Description POWER On Router is switched on and correctl y powered. On Wirele ss WPS f unction is enable d. Off Wirele ss net work i s swit ched off. WLAN Flashing Wirele ss LAN activi ty (transfe rring or receiving data). On WAN por t is connect ed. Off WAN por t is not co nnecte[...]

5 Back Panel Item Name Description Antenna A/B* These antennas are 3dBi dipole antennas. Radio ON/OFF Switch the button to activate or deactivate the wireless functions. Reset / WPS Reset the router to factory default settings (clear all settings) or start WPS function. Press this button and hold for 10 seconds to restore all settings to factory de[...]

6 Chapter II : System and Network Setu p 2 - 1 Network C onnection s 1. C onnect your USB modem to the USB port located o n the front panel of the router. 2. Connect your xDSL / cabl e modem to th e WAN port of router by Ethernet cable . NOTE: G o to Section 3 - 4 Fail Over to assign the WAN con nection priority if you have su bscribed to bo th 3G [...]

7 3. Con nect all your computers, network devices (network - enabled consumer devices other than computers, like game console s or switch es / hub s ) to the LAN port of the router. 4. Connect the AC power adapt er to the wall socket , then connect it to the Power s ocket of the route r.[...]

8 5. C heck all LEDs on the front panel. The P ower LE D s ho u ld b e on ; the WAN, LAN and USB LEDs should be on if t he com puter / network device connected to t he respective port s of the router are p o w e r e d o n a n d c o r r e c t l y c o n n e c t e d . I f the Power L E D is not on, or if any LED you expected to be on is n’t , re - c[...]

9 2 - 2 Connecting to the R outer via W eb B rowser After the net work connection is established , the next step is to set up the router with pr oper network parameters so it can work properly in your network envi ronment. Before you can connect to the router and start the configuration procedures, your computer must be abl e to obtain an IP addres[...]

10 2. Select “ Obtain an IP address from a DHCP server ” a n d th e n c l i c k “ OK. ”[...]

11 2 - 2 - 2 Windows 2000 IP A ddress S etup 1. Click St art (at the lower - left corner of your desktop ), then click C ontrol P anel. Double - click the Network and D i al - up Connections icon; click Local Area Connection ; the Local Area Connectio n Properties window will appear. Select “ Intern et Protocol (TC P/IP) ” and then click “ Pr[...]

12 2. Select “ Obtain an IP addre ss automatica lly ” and “ Obtain DNS server address automatically, ” then click “ OK. ”[...]

13 2 - 2 - 3 Windows XP IP A ddress S etup 1. Click St art (at the lower - left corner of your desktop ), then click C ontrol P anel. Double - click the Network and Int ernet Connections icon, click Network Conn ections, then double - click Local Area Connection ; the Local Area Connection St atus window will appe ar. Click “ Properties .”[...]

14 2. Select “ Obtain an IP addre ss automatically ” and “ Obtain DNS server address automatically ,” then click “ OK. ”[...]

15 2 - 2 - 4 Windows Vista /7 IP A ddress S etup 1. Click St art (at the lower - left corner of your desktop ), then click C ontrol P anel. Click View Network Stat us and Tas ks , and then click Manage Ne twork Connec tions. Ri ght - click Local Area Network , then select “ Properties. ” T he Local Ar ea Connection Pr operties window will appea[...]

16 2. Select “ Obtain an IP addre ss automatica lly ” and “ Obtain DNS server address automatically, ” then click “ OK. ”[...]

17[...]

18 2 - 2 - 5 Router IP A ddress L ookup After the IP address setup is complete, go to S tart, then R un at the bottom - lower corner of yo ur desktop: Input “ cmd, ” then c lick “ OK .”[...]

19 Input “ ipconfig, ” t he n p re ss < Enter > . C heck the IP address followed by the d efault g ateway (i n this example, the IP address of the router is 192.168.2.1 ) . 3. Connect the router ’ s management int er face by W eb browser After your comput er obtain s an IP address from the router, start your W eb browser and input the I[...]

20 Enter a user name and pa ssword in their re spective field s ( default user name is “ admin ”; d efault password is “ 1234 ”). Cli ck “ OK ” b and you can see the W eb management interface of th e router . NOTE: If you can’t see the Web management interface and you’re being prompted to input the user name and p assword again, it [...]

21 2 - 3 Using Quick Setup Quick Setup lets you complete all the required settings you need in order to access the Inter net very quickly . Click “ Quick Setup ” on the left - hand navigation panel. T he following message will be di splayed: 1. Set Time Zone Below are descriptions of each option : Set Time Click and a drop - dow n list wil l be[...]

22 Time Server Input the IP add ress / host nam e of time se rver Address (2): here . Daylight If the country yo u live in uses D aylight S aving, Savings (3): check “ Enable Function ” and choose t he duration of D aylight S aving. After you fin ish the settings, click “ Next ” (4). NOTE: There are several time servers available on the Int[...]

23 2. Broadband Type C hoose the broadband (Internet connecti on) type you ’ re using . T here are seven types of Internet connection s: 3G/3.5G - go to section 2 -3-1 Cable Modem - go to section 2 -3-2 Fixed - IP xDSL - go to section 2 - 3-3 PPPoE xDSL - go to section 2 -3-4 PPTP xDSL - go to section 2 -3-5 L2TP xDSL - go to section 2 -3-6 Telst[...]

24 3. Basic Setting s Below are d escriptions of each option : Wireless Module ( 1) : C lick “ Enable ” to start using the wireless function of this ro uter, or select “ Disable ” to close the wireless inter face of this router. Band (2): S ele ct a b an d type fro m the drop - dow n list . It allows you to set the router at 802.11b or 802.[...]

25 ( maximum 3 2 cha racter s ) . SS ID is used to identify your ow n wireless ro uter from othe rs when ther e are other wireless rout ers in the area. Default SSID is “I NTELLINET”; it ’ s r ecommended to change the default SSID name to one that is easily recognizable, such as “ my home, ” “ office_room1, ” etc. Channel Number ( 4):[...]

26 4. Security Settings C hoose the Encryption type you ’ re using from the drop - down l ist . T here are three types of Encrypt ion : WEP - go to section 2 -7-3-2 WPA pre - shared key - go to section 2 -7-3-3 WPA RADI US - go to sec tion 2 -7-3- 4 T o go back to a previous step, click “ Back ” at the bottom of th e page. 2 - 3 - 1 Setup P r[...]

27 Below are d escriptions of each option : PIN Code (1): Enter a P in Code for your UMTS or H SDPA or EVDO connection . T his is optional, and is only required if your service provider asks you to do so. APN (2): Enter the APN code assig ned by your Internet service provider here. User Name (3): Enter the user name assigned by your Internet servic[...]

28 2 - 3 - 2 Setup P rocedure for Cable Modem Below are d escriptions of each option : Host Name (1): Enter the host name of your com puter T his is optional, and is only required if your s ervice provider asks you to do so. MAC Addr ess (2 ): Enter the MAC add ress of you r comput er her e if your service provider only permits computer s with a ce[...]

29 2 - 3 - 3 Setup P rocedure for Fixed - IP xDSL Below are d escriptions of the options : IP address (1 ): Enter the IP address assigned by your serv ice provider . Subnet Mask (2): Enter the subnet mask as signed by yo ur service provider . DNS Address (3 ): Enter the IP address o f the DNS server provided by your service provi der. Defau lt Gate[...]

30 Below are d escriptions of each option : User Name (1): Enter the user name assigne d by your Inte rnet service provider here. Password (2): En ter the passwo rd assigned b y your Interne t service provider here. Service Name (3): Assign a name to this Internet se rvice ( optional ). MTU (4) : Enter the MTU value of you r network connection here[...]

31 When yo u fini sh the settin gs, click “ Next ” ( 7) ; to go b ack to a previous menu, click “ Back. ” 2 - 3 - 5 Setup P rocedure for PPTP xDSL PPTP xDSL requires t wo kinds of set ting s : WAN I nterface S etting s (setup IP address) and PPTP S etting s (PPTP us er name an d password). First, WA N I nterface S etting s: Select how you o[...]

32 In ternet conn ection will fail ev en if the PPT P settings are correct. C ontact your Internet service provider if you don ’ t know how you should fill in these fields. N ext, PPTP S ettings: Below are d escriptions of each option : User Name (1): Enter the user name assigne d by your Inte rnet service provider here. Password (2): Enter the p[...]

33 Connection Ty pe : S elect the conn ection type of In ternet (7) connection you w ant to use ( refer to the last section for detailed descriptions ). Idle Time Ou t (8): Enter t he idle time out of the Internet connection you w ant to use ( refer to the last section for detailed descriptions ). When yo u fini sh the settin gs, click “ Next ”[...]

34 Next, L2TP S ettings: Below are d escriptions of each option : User Name (1): Enter the user name assigne d by your Inte rnet service provider here. Password (2): Enter the password assigned by your Intern et service provider here. L2TP Gateway (3): Enter t he IP address of P PTP gateway assigned by your Internet service provider here. MTU (4) :[...]

35 2 - 3 - 7 Setup P rocedure for Telstra Big Pond This setting only works when you ’ re using Telstra B ig P ond ’ s network service in Australi a. User Name (1): Enter the user name a ssigned by T elstra. Password (2): Enter the password as sign ed by Telstra. Assign login Check this box to choose a login server by server manually yourself. ([...]

36 C lick “ Apply ” to prepare to restart the ro uter, and you ’ ll se e this message: W ait for about 30 seconds, then click “ OK! ” Yo u’ ll be b ack to the router management interface, and the router is ready with new settings.[...]

37 2 - 4 Basic Setup In this chapter, y ou ’ ll see how to ch ange the time zone, passw ord a nd remote management settings. S tart your W eb browser and log on to the router ’s W eb management interface, then cli ck “ General Setup ” on the left (or click the “ General Setup ” link at the upper - right corner of the scre en) . 2 - 4 - [...]

38 Below are d escriptions of each option : Time Zone (1): S elect a time zone from the drop - down list. Time Server Enter the IP address or h ost name of the time Address (2): server here. Daylight C heck the “ Enable ” box and s et the duration Saving (3): of D aylight Savi ng. When yo u fini sh, click “ Appl y. ” You ’ ll see the fo l[...]

39 2 - 4 - 2 Chang ing th e M anagement P assword The d efault password of t his router is 1234, a nd it ’ s displayed on the login prom pt when acce ssed from the W eb browser. There ’ s a security risk if you don ’ t chang e the default pa ssword, sinc e everyone can see it. This is very important when you have the wireless f unction enabl [...]

40 Re - enter the new passw ord if you see a bove mess age. If you see the following message, the content in the “ C u rrent Pas sword ” field is wrong. C lick “ OK ” to go ba ck to the previous menu, an d try to enter the current password again . If the current an d new passwords are correctly en tered, after you click “ Apply ” you ?[...]

41 2 - 4 - 3 Remote Management This router does not allow management access from the Internet to prevent possible security risks (as when a too - simple p assword is used or when the default password isn’t c hanged ). Howev er, you can still management this router from a specific IP address by enabling the Remote Management f unction. C lick “ [...]

42 Click “ Continue ” to save the settings and go back to the W eb management interface; click “ Apply ” t o s a v e t h e s e t t i n g s a n d r e s t a r t the router so th e settings will tak e effect after it reb oots. NOTE: When you want to manage this router from another computer on the Internet, you need to input the IP address and [...]

43 2 - 5 Set ting U p the Internet Conne ction (W AN ) Internet conne ction setup ca n be done by usin g Quick Setup as described in Section 2 - 3. However, you can also set up WAN connections up by using the WAN conf iguration m enu. Y ou can also set advanced functions like DDNS (Dynamic DNS) here. C lick “ WAN ” on th e l ef t side of the W [...]

44 PPTP - go to section 2 -5- 5 L2TP - go to section 2 -5 -6 Telstra Big Pond - go to se ction 2 -5-7 DNS - go to sectio n 2 -5-8 DDNS - go to s ection 2 -5-9 2 - 5 - 1 Setup P rocedure for 3G / 3.5G Below are d escriptions of each option : PIN Code (1): Enter the P in Code for your U M TS or HSDPA connection . T his is optional, and is required on[...]

45 Verify Password (5): Enter the password again for conf irmation. Service (6): S elect your c ard type from the dro p - down menu. AT Dial Script (7): Enter the dialed n umber for your U MTS or HSDPA connection. T he default is *99#. This field should no t be altered exc ept when required by your service provider. After you fin ish the settings, [...]

46 2 - 5 - 2 Setup P rocedure for Dynamic IP Below are d escriptions of each option : Host Name (1): Enter the host name of your computer . T his is optional, and is only required if your service provider asks you to do so. MAC A ddress (2): Enter the MAC add ress of your computer if your service provider only permits computer s w ith certain MAC a[...]

47 C lick “ Conti nue ” to go back and continue with the router setup, or click “ Apply ” to reboot the router so the settings will take effect. (W ait for about 30 seconds whil e the router is rebooting .) 2 - 5 - 3 Setup P rocedure for Static IP Below are d escriptions of e ach option : IP address (1 ): Enter the IP address assigned by yo[...]

48 message wi ll be displa yed on y our W eb browser: C lick “ Continue ” to go back and continue with the router setup, or click “ Apply ” to reboot the router so the settings will take effect. (W ait for about 30 seconds whil e the router is rebooting .) If you want to re set all settings o n this page back to previously saved value s , c[...]

49 Password (2): Enter the password assigned by your Intern et service provider here. Service Name (3): Enter a name for this Interne t service. (T his is optional .) MTU (4) : Enter the MTU value of you r network connection here. If you don ’ t know it, contact your ISP . Connection S elect the connection type of the Internet Type (5): connectio[...]

50 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot t he router so the settings will take effect. (W ait for about 30 seconds while the router is rebooting .) If you want to re set all settings o n this page back to previously saved value s , click “ Cancel .” 2 - 5 - 5 Setup P r[...]

51 your Internet servi ce provider if you don ’ t know how you should fill in these fields. N ext, PPTP S ettings: Below are d escriptions of each option : User Name (1): Enter the user name assigne d by your Inte rnet service provider here. Password (2): Enter the password assigned by your Intern et service provider here. PPTP Gateway Enter the [...]

52 Connection S elect the connection type of the Internet Type (7): connection you w ant to use. (R efer to section 2-5- 3 for detailed descriptions. ) Idle Time Ou t (8): Enter the idle time o ut of the Internet connection you want to use. (R efer to section 2-5- 3 for detailed descriptions. ) When yo u fini sh the settin gs, click “ Apply ” ([...]

53 Below are d escriptions of each option : User Name (1): Enter the user name assigne d by your Inte rnet service provider here. Password (2): Enter the password assigned by your Intern et service provider here. L2TP Gateway (3): Enter t he IP address of the PPTP gateway assigned by your Internet service provider here. MTU (4) : Enter the MTU valu[...]

54 If you wa nt to reset all settings o n thi s page back to previously saved value s , click “ Cancel .” 2 - 5 - 7 Setup P rocedure for Telstra Big Pond Th ese setting s only work wh en you ’ re using Telstra B ig P ond ’ s network service in Australia. User Name (1): Enter the user name assigned by Telstra. Password (2): Enter the passwor[...]

55 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effe ct . (W ait for about 30 seconds while the router is rebooting .) If you want to re set all settings o n this page back to previously saved value s , click “ Cancel .” 2 - 5 - 8 Setup P[...]

56 Below are d escriptions of each option : Primary DNS (1): Enter the IP addres s of the DNS server provided by your service provi der. Secondary DNS Enter the IP address of an other DNS s erver (2): provided by your service provider (this i s optional ). After you fin ish the settings, click “ Apply ” (3) and the following message wi ll be di[...]

57 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the se ttings will take effect. (W ait for about 30 seconds while the router is rebooting .) If you want to re set all settings o n this page back to previously saved value s , click “ Cancel .” 2 - 5 - 9 Setup P r[...]

58 Below are d escriptions of each option : Dynamic DNS (1): If yo u want to enable the DDNS function, select “ Enabled ” ; otherwise , sele ct “ Disabled .” Provider (2): Select your DDNS ser vice provider here. Domain Name (3): Enter the domain nam e you ’ ve obtained from the DDNS service prov ider. Account / Enter acco unt or e - mail[...]

59 procedure , or click “ Apply ” to reboot the router so the s ettings will take effect. (W ait for about 30 seconds while the router is rebooting .) If you want to re set all settings o n this page back to previously saved value s, click “ Cancel .” 2 - 6 Wired LAN Config urati on s Before all co mputers using wir ed Ethernet con nection [...]

60 Suggestions for a IP address numbering plan: If you have no idea how to define an IP address plan for your network, here are some suggestions. 1. A valid IP address has 4 fields: a.b.c.d. For most home and company users, it ’s suggested to use 192.168.c.d, where c is an integer between 0 and 254, and d is an integer betwe en 1 and 254. This ro[...]

61 C lick LAN on the left side of the W eb management interface . T here are three setup groups here: “ LAN IP ,” “ DHCP Server ” and “ Static DHCP Leases Tabl e .” 2 - 6 - 1 LAN IP Below are descri ptions of th e options : IP address (1 ): Enter the IP address of this router. Subnet Mask (2): Enter the subnet mask for this network. 802[...]

62 2 - 6 - 2 DHCP Server These settings are onl y avai lable when “ DHCP Server ” in “ LAN IP ” is e nabled . Below are descript ions of the o ptions : Lease Time (1): C hoose a lease time (the duration that ever y computer can keep a specific I P address) of every IP address assigned by thi s router from the drop - down menu. Start IP (2) [...]

63 2 - 6 - 3 Static DHCP Leases Table This function allows you to assign a stat ic IP address to a specific computer forever, so you don ’ t have to set the IP a ddress for a computer, but can still enjoy the benefit o f using DHCP server. A m aximum of 16 static IP addresses can be a ssigned here . (If you set “ Lease Time ” to “ foreve r [...]

64 After you cli ck “ Add ,” the MAC addre ss and IP add ress mapp ing will be a dded to the Static DHCP Le ase s Table section. If you want to de lete a specific ite m, check the “ Select ” box of a MAC ad dress and IP a ddress mapping (1), then cl ick “ Delete ” (2) ; if you want to de lete all mappin gs, click “ Delete All ” (3).[...]

65 2 - 7 Wirel ess LAN Conf igur ations If your compu ter, PDA, gam e console or o ther network device is equipped with a wirel ess network i nterface, you can use the wireless f unction of this router to let the m connect to the Internet and share resources with other computers with a wired LAN connection. You can also use t he built - in secu rit[...]

66 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effect. (W ait for about 30 seconds while the router is rebooting .) 2-7- 1 Basic Wireless Settings C lick Wireles s on the left side o f the W eb management interface, then click “ Basic Sett[...]

67 SSID (2): This is the name of the wi reless router. Yo u can type any alph anumerical c haracters he re ( maximum of 32 characters ) . ESSID is used to identify your ow n wireless ro uter from othe rs when ther e are other wireless rout ers in the same are a. The d efault SSID is “INTELLINET”; 2.4 GHz (B) 2.4GHz band only allows 802.11b wire[...]

68 it ’ s recommended to change default ESSID name to one that is meaningfu l to you, such as “ myhome, ” “ office_r oom1, ” etc. Channel Number S elect a channel from the drop - down list . (3): A vailable channel numbers are 1 t o 13 fo r European countr ies ; 1 to 11 for the U . S. You can choose any channel number you want to use, and[...]

69 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effect. (W ait for about 30 seconds while the router is rebooting .) 2-7- 2 Advanced Wireless Settings This router provides some advanc ed control of wireless parameters . C lick Wireles s on th[...]

70 Below are descri ptions of th e options : F ragment Set the thres hold of the wirele ss radio . Threshold (1): Do not modify the defaul t value if you don ’ t know what it doe s ( default value i s 2346 ). RTS Threshold (2): Set the RTS thr eshold of the wir eless r adio. Do not modify the default value i f you don ’ t know what it doe s ( d[...]

71 your wireless router (set the option to “ Disable ” ) so only those who know the ESSID of your wireless router can connect . CTS Protect (10): Enabling t his setting will reduce the chance of radio signal collisions between 802.11b and 802.11g/n wireless access points. It ’ s recommended to set this option to “ Auto ” or “ Always .?[...]

72 2-7- 3 Wireless Security It ’ s very important to set wirel ess security settings properly! If you don ’ t, hackers an d malicious u sers can re ach your network and valuable data without your consent , causing a serio us security problem. C lick Wireles s on the left side of the W eb management interface, then click “ Security Settings .?[...]

73 Below are descri ptions of th e options : Key Length (2) : There are two types of WEP k ey length: 64 - bit and 128 - bit. “ 128 - bit ” is safer than “ 64 - bit ” but will red uce some d ata tran sfer per formance. Key Format (3): There are two types of key format: ASCII and Hex. When you select a key for mat, t he number of characters [...]

74 key here ; if you enter mu ltiple WEP key s, they should all be different . Enable 802.1x IEEE 802.1x is an authenticatio n protocol. Authentication (9): Every user must use a valid account to log in to this wireless ro uter before ac cessing the wireless LAN. The authenti cation i s proces sed by a RAD IUS server. This mode only authenticates u[...]

75 After you fin ish the WEP set ting s , click “ Apply ” (10) and the following will be displayed on y our W eb browser: C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effect. (W ait for about 30 seconds while the router reboot s. ) 2 - 7 [...]

76 Pre - shared Select the type of pre - shared key . Y ou Key Format (3): can select Passphrase (8 or more alphanumerical characters, up t o 63), or Hex (64 characters of 0 - 9 and a - f). Pre - shared Enter the W PA passph rase here. Key (4): It ’ s not recommended to use a word that can b e found in a dictionary due to security reason s. After[...]

77 Below are descri ptions of th e options : WPA Unica st S elect a type of WPA cipher suite. O ptions are Cipher Suit e (2): “ WPA ( TKIP), ” “ WPA2 (AES) ” and “ WPA2 Mixe d. ” You can select any one of them, but you have to make sure your wireless cl ient support s the cipher yo u selected. RADIUS Server Enter the IP address of y our[...]

78 2-7- 4 Wireless Access Control This function will help you to prevent unauthorized users fr om connecting to y our wireless router; o n ly those wireless devices who have the MAC add ress you as signed here c an gain acce ss to your wireless ro uter. You can use thi s function with other security measures describe d in p revious section , to cre[...]

79 Enable Wireless To enforce MAC address fil tering, check Access Control ( 4): “ Enable Wirele ss Access Control .” When this item is unche cked, the router will not enforce MAC addr ess f ilt ering of wirel ess cl ients . MAC Addr ess (5 ): Input the M AC addre ss of your wire less devices here . D ashes ( - ) and colon s ( : ) a re not requ[...]

80 2 - 7 - 5 Wi - Fi Protected Setup (WPS) Wi - Fi Protected Setup (WPS) is the simplest way to build a connection between wireless network clients a nd this wireles s router. You don ’ t hav e to select an encryption mode or input a long encryption passphrase every ti me you need to set up a wireless client : Y ou only need to press a button on [...]

81 Below are descri ptions of th e options : Enable WPS (1): Check this box to enab le WPS funct ion ; uncheck it to disable WPS. Wi - Fi Protect ed WPS - related system inform ation will be Setup Informatio n displayed here: (2): WPS Status : If the wireless security (encryption) function of this w ireless router is properly set, you ’ ll see ?[...]

82 Configure Click “ Start PBC " to start Push Button - style by Push Button WPS setup pr ocedure. This wireles s route r will (4): wait for WPS reque sts from wireless clients for 2 minutes. The WLAN LED on the wireless router will be lit for 2 mi nu tes w he n th is wi re le ss router is waiting for incoming WPS reques t s. Configure Enter[...]

83 Chapter II I Advanced Func tions 3 - 1 Quality of Service (QoS) Quality of service pr ovides an ef ficient way for comput ers on the network to share the I nternet bandwidth with a promised quali ty of I nternet service. Without QoS, all computers and devices on t he network w i l l c o m p e te w it h ea ch ot he r t o g e t I nternet bandwidth[...]

84 Enable QoS (1): Check this box to enable the QoS fun ction ; de - select this box if you don ’ t want to e nforce QoS bandwidth limitatio ns. Total Download You can set the limit of total download Bandwidth (2): bandwidth in kbits. To disable the download bandwidth limitation, enter “0” here. Total Upload You can set the limit of tot al up[...]

85 selected by clicking t his button. Move D o wn (1 0): You can lower the prior ity of the QoS rule you selected by clicking t his button. After you fin ish the settings, click “ Apply ” (11) and the following message wi ll be displa yed on y our W eb browser: C lick “ Continue ” to go back and continue with the router setup procedure , or[...]

86 Below are descri ptions of th e options : Rule Name (a): Enter a name for this Q oS rule (u p to 15 alphanumerical characters) . Bandwidth (b): Set the bandwidth l imitation of t his QoS rule. You need to se le ct th e d at a d ire ct io n o f t hi s r ule (Upload o r Dow nload), and the speed of bandwidth limitation in k bps, then select the ty[...]

87 Remote IP Specify the re mote (destinatio n) IP address Address: (e): that will be affec ted by this rule . I nput the starting IP address in the left fiel d and input the end IP address in the ri ght field to def ine a range of IP addresses, or just input the IP address in the left field to define a single IP addre ss. Remote Port I nput the ra[...]

88 3 - 2 Network A ddress Translation (NAT) Network addres s translat ions solve the problem o f sharing a sin gle IP address on mu ltiple compute rs. Without NA T, all compute rs must be assigned a val id Int ernet I P address to g et conn ected t o the Internet, but In ternet service pr oviders provide only a very few IP addresses to each user. T[...]

89 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effect. (W ait for about 30 seconds while the router reboot s. ) 3 - 2 - 2 Port Forwarding This function all ows you to redirect a single port or consecutive ports of an In ternet IP address to [...]

90 Below are descri ptions of th e options : Enable Port Check this box to ena ble port mapp ing ; Forwarding (1): uncheck this box to disab le port mapp ing. Private IP (2 ): Input the IP address o f the compu ter on the local network that provides I nternet service. Computer Name Pull down the menu and all the computer s (3): connected to the rou[...]

91 Reset (12): Unselect all mappings. After you fin ish the settings, click “ Apply ” (13) and the following message wi ll be displa yed on y our W eb browser: C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effect. (W ait for about 30 secon[...]

92 Below are descri ptions of t he opt ions : Enable Virtual Check th is box to enable the virtual server; Server (1): uncheck this box to disable it . Private IP (2 ): In put the IP address of the computer which provides Internet service. Compute r Name Pull down the menu and a ll the compute rs (3): connected to the router will be li sted here. Y[...]

93 Reset (9): Remove all enter ed values. Virtual Server All exist ing virtual server mappings wil l be Table (10): displa yed here. Delete (11) : S elect a virtual server mapping by clicking the “ Select ” box of the mapp ing, then click “ Delete Selected ” to remove the m apping. If there ’ s no existing mapping, this but ton will be gr[...]

94 3 - 2 - 4 Port Mapping for Special Applications Some applications require more t han one connection a time; these applications won ’ t work with sim ple NAT rules . In order to ma ke these applica tions work, you can use this func tion . Below are descri ptions of th e options : Enable (1): Check this box to enabl e special applications ; unch[...]

95 Popula r This section lists the more popular applicati ons Applications ( 7): that re qui re multiple connections. Select an application from the “ Popular Applications ” section and click “ Add ” to sav e the setting to “ Current Trig ger - Port Table. ” Add (8): Add the setting to t he “ Current Tri gger - Port Table. ” Reset ([...]

96 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effect. (W ait for about 30 seconds while the router reboot s. ) If you want to re set all settings o n this page back to previously saved value s , click “ Cancel .” 3 - 2 - 5 U PnP Setting[...]

97 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effect . (W ait for about 30 seconds while the router reboot s. ) If you want to re set all settings o n this page back to previously saved value s , click “ Cancel .” 3 - 2 - 6 ALG Settings[...]

98 There are many applications listed here. C heck the box of the special support for appl ications you need, then click “ Apply .” T he following mes sage will be dis played on yo ur W eb browser: C lick “ Continue ” to go back and cont inue with the router s etup procedure , or click “ Apply ” to reboot the router so the s ettings wil[...]

99 3 - 3 Firewall In addition to NA T, this router p rov ides firewall function s to b lock malicio us intr uders f rom acce ssing yo ur comput ers on your local network. These functions i nclude inbound attack preventi on and block ing of outbound traffic, such as block ing URLs that have pre - defined keywords. C lick “ Firewall ” on the left[...]

100 3 - 3 - 1 Access Control This function all ows or denies computers wit h specific MAC addresses access to the network; it can also allow or deny computers with a specific IP address, protocol or port. C lick “ Firewall ” on the left side of the W eb managem ent interface, then click “ Access Control .” T he following message will be dis[...]

101 “ aa:bb:cc:dd:ee:ff ,” just input “ aabb ccddeeff .” Computer Name Pull down the menu and all the computer s (3): connected to the router will be li sted here. You can select t he computer name without checking the IP address of the compu ter. Comment (4): You can input any text here as a commen t about this MAC ad dress, such as “ RO[...]

102 the network; if y ou select “A llow, ” o nly IP addresses listed in th e fil te ri ng ta bl e w i ll b e a b le to connect to th e net work, and all ot her network devices will be rejected . IP Filtering All existing IP addresses in the fi lte ri ng t ab le w il l Table (12): be listed here. Add PC (13): Click to add a new I P address t o t[...]

103 3 - 3 - 1 - 1 Add PC After this button is cli cked, the following message wi ll be displayed on your W eb browser: Below are descri ptions of th e options : Client PC Enter any text to desc ribe this IP addre ss. (Up Description (a): to 16 a lphan umerical characters. ) Client PC IP I nput the starting IP address in the left a b c d e f[...]

104 address (b): field a nd input the end IP address in the right field to define a ra nge of IP addre sses, or just input the IP add ress in the left field to define a single IP addr ess. Client PC C heck all the services you want to allow or Service (c): deny this IP address to use . Y ou can check multi ple s ervice s. Protocol (d): If the servi[...]

105 Below are descri ptions of th e options : Enable URL Check this box to enforc e URL Bloc king ; Blocking (1): uncheck it to disable URL Blocki ng. URL/Keyword (2) : Input th e URL (host n ame or IP ad dress of the W eb site , like http://www.blocked - site.com or http://11.22.33.44 ), or the keyword that is contained in the URL (like por nograp[...]

106 Delete All (7): If you want to de lete all URL/Ke yword entries listed here, click “ Delete All .” Reset (8): You can also cl ick “ Reset ” to unselect all URL/Keyword entries . After you fin ish the settings, click “ Apply ” ( 9 ) and the following message wi ll be displa yed on y our W eb browser: C lick “ Continue ” to go bac[...]

107 Below are descri ptions of th e options : Ping of Death ( 1): Ping of Death is a speci al packet, an d it will cause certain computer s to stop respo nding. Check this box and the router wil l filte r this ki nd of packet out. Discard Ping Ping is a common and useful tool for learning f rom WAN (2 ): the connection sta tus of a specifie d remot[...]

108 server become unusable. Check this box and the router will filter this kind of traffic o ut. Advanced Click this butt on and you c an set advanc ed Settings (5): sett in gs of the DoS prevention method l isted above ( see section 3 -3-3- 1 DoS – Adva nced Settings below ). After you fin ish the settings, click “ Apply ” ( 9 ) and the foll[...]

109 Below are descri ptions of th e options : Ping of Death ( a): Set the threshold for when this DoS preve ntion m echanism will be activated. C heck the box of Ping of Death, and input the frequency of the threshold (ho w many pac kets per sec ond, minute or h our) . Y ou can al so input the “ Burst ” value, which means when this number of Pi[...]

110 C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings will take effect. (W ait for about 30 seconds while the router reboot s. ) If you want to re set all settings o n th is pa ge back to pr eviously saved value s , click “ Cancel .” 3 - 3 - 4 Demilitar[...]

111 Below are de scripti ons of the options : Enable DMZ (1): Check t his box to enable the DMZ functi on ; uncheck this box to disabl e the DMZ function. Pu blic IP Yo u can select “ Dynamic IP ” or “ Static IP ” here. address (2): If you select “ Dynamic IP ,” you need to sele ct an Internet connection sessi on from the drop - down me[...]

112 Reset (10): You can also click “ Reset ” to unselect all D MZ entries. After you fin ish the settings, click “ Apply ” ( 11 ) and the following message wi ll be displa yed on y our W eb browser: C lick “ Continue ” to go back and continue with the router setup procedure , or click “ Apply ” to reboot the router so the s ettings [...]

113 3 - 4 Fa il Over WAN fai lure detect ion wo rks by detec ting the pr esence of t raffi c on the 3G modem link. If the link is idle for too lon g , the router will attempt to ping a t arget IP address. If the ping does not reply, the router assumes the link is down and attemp ts to fail over to an E thernet WA N link. Below are descri ptions of [...]

114 Ping Target IP ( 4 ): I npu t the target IP ad dress you want t o p i n g o u t . If the major I nternet co nnecti on is idle for too long , the route r will attempt to p ing the target IP address. E- Mail If you enable the E - Mail No tif icati on functi on, Notificat ion (5): when the WAN connection fails the router w ill automatically attemp[...]

115 3 - 5 System Status The functions descri bed here will provide you with system - related information. To enter the S ystem S tatu s menu, either click the “ Status ” link in the upper - righ t corner of the W eb management interface or clic k “ Status ” in t he main men u. 3 - 5 - 1 System I nformation and F irmware V ersion Click “ S[...]

116 This information wil l vary depending on the c onnection status. 3 - 5 - 3 Device Status C lick “ Device Status ” on the l eft side of the W eb management interface, and the following mess age will be displayed on your W eb browser:[...]

117 This information wil l vary depending on the devi ce status. 3 - 5 - 4 System Log All important system events are logged. You can use this func tion to check the e vent log of your router. Cl ick “ System Log ” on th e left side of the W eb management interface, and the following message will be displayed on your W eb browser: Below are des[...]

118 Cl ick “ Security Log ” on the left side of the W eb management interface, and the following message will be displayed on your W eb browser: Below are descri ptions of th e options : Save (1): Save the current event log to a text f ile. Clear (2): Delete all event logs dis played h ere. Refresh (3): Refresh the event log display. 3 - 5 - 6 [...]

119 All informatio n about active DHCP leases issued b y this router will be displayed here. C lick “ Refresh ’ to display the latest inform ation . 3 - 5 - 7 Statistics You can use thi s function t o check the st atistics of the wirel ess, LAN and WAN interface s of this router. C lick “ Statistics ” on the left side of the W eb management[...]

120 3 - 6 Configuration Backup and Restore You can back up all con figuratio ns of th is router to a file s o you ca n make seve ral cop ie s of the router configuration for security reason s. C lick “ Tool s” at the upp er - right corner of the W eb management interface, then c lick “ Configuration Tools ” on the left side of the W eb mana[...]

121 configuration wi l l b e r e pl a c e d b y t h e fi l e y o u j u st uploaded. Restore to Click to remove all s et tings you made and Factory Default restore the configuration of this router back to (3): factory default s ettings. 3 - 7 Firmware Upgrade The system software used by th e ro u t e r i s referred to a s “ firmware,” just like [...]

122 Click “ Browse ” first and you ’ ll be prompted to provide the file name of the firmware upg rade file. Do wnload the latest f irmware fi le from www.intelli net - network.com and use it to upgrad e your router . After a fir mware upgrade fil e is selected, click “ Apply ” and the router will start the firmwa re upgrade p rocedu re au[...]

123 C lick “ Apply ” to reset y our router. It will be a vailable again after a few minutes.[...]

124 Chapter IV: Appendix 4 - 1 Specification s Standards • IEEE 802.1d (Spanning Tree Protocol) • IEEE 802.11b (11 Mbps Wireless LAN) • IEEE 802.11g (54 Mbps Wireless LAN) • IEEE 802.11n Draft 2.0 (300 Mbps Wireless LAN) • IEEE 802.3 (10Base- T E thernet) • IEEE 802.3u (100Base-TX Fast Ethernet) General • LAN ports: 4 RJ45 10/100 Mbps[...]

125 - ICMP - PPPoE - NTP - NAT - DHCP - DNS • NAT: - Virtual server - Port forwarding - Special applications (port trigger) • Firewall: - Access control based on MAC address - URL filter - DMZ (demilitarized zone) • Supports UPnP (Universal Plug and Play) • Supports DHCP (client/server) • Supports WPS (WiFi Protected Setup) • VPN passth[...]

126 - IEEE 802.11n (MCS0-15: up to 300 Mbps) • Output power: - OFDM: 15 dBm +/- 1 dBm (300 Mbps, 40 mW max.) - OFDM: 15 dBm +/- 1 dBm (54 Mbps, 40 mW max.) - CCK: 17 dBm +/- 1 dBm (11 Mbps, 63 mW max.) • Receiver sensitivity: - 11n ( 15 0 Mbps) MCS0- 07 : 20 MHz: -73 dBm; 40 MHz: -68 dBm - 11n (300 Mbps) MCS0-15: 20 MHz: -73 dBm; 40 MHz: -68 dB[...]

127 Power • External power adapter: 12 V DC, 1.0 A • Power consumption: 5 W max., Model 524681; 3.5 W max., Model 524940 Package Contents • Wireless 3G Router (150N or 300N) • User manual on CD, plus quick install guide • Power adapter • Ethernet Cat5 RJ45 cable: 1.0 m (3 ft.) • USB extension cable: 1.0 m (3 ft.)[...]

128 4 - 2 Troubleshooting If you f i nd the router is working improperly or has stop ped responding , see if a possible solution appears in this section b efore you contact your dealer of purchase for help . Scenario Solution Router is not responding when I try to access it b y W eb browser . a. C heck the router’s power cord and network cable co[...]

129 connected to the I nternet with your computer directly attached t o the device provided by your I n ternet service provider. d. Check the PPPoE / L2TP / PPTP user ID and passw ord again. e. Call your Internet s ervice provi de r and check if there ’ s something wrong with their service. f. If y ou just can ’ t co nnect to one o r more W eb [...]

130 d. If this never hap pen ed before, ca ll you r Internet servic e provide r to see if there is something w rong with the ir network. I can ’ t log on to the W eb management interface ; the password is wrong . a. Make sure you ’ re connecting to the correct IP address of t he router . b. The p assword is case - sensitive. Make sure t he C ap[...]

131 4 - 3 Glossary Default Gateway (Router): Every non - router IP device needs to configure a default gat eway’s IP address. When the device sends out an IP packet, if the destination i s not on the same network, t he device has to send the packet to its default ga tewa y, which will then send it out toward t he destination. DHCP: Dynamic Host C[...]

132 computer host in an IP net work. Example: 192.168.2.1. It consists of 2 portions: the IP network address, and the host identifier. The IP address is a 32 - bit binar y patter n, which can be represented as four cascaded decimal numbers separated by “.”: aaa.aaa.aaa.aaa, where each “aaa” can be anything from 000 to 255, or as four cascad[...]

133 MAC Addres s: MAC st ands fo r Media Access Control. A MAC address is the hardware address of a device connected to a network. The MAC address is a unique identifier for a device with an Ethernet interface. It is comprised of t wo parts: 3 bytes of data that correspo nds to the Man ufacturer ID (unique for each manufact urer), plus 3 bytes that[...]

134 transmitting info rmation over Ethernet betw een different manufact urers . Protocol: A pro tocol is a se t of rules f or interacti on agreed upon between multiple parties so that when they interf ace with each other based on such a protocol , the interpretati on of their behavior is well defined a nd can be m ade objective ly, without confu si[...]

135[...]