Français dropdown-ico

Jet JWBS-18X manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Jet JWBS-18X. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Jet JWBS-18X ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Jet JWBS-18X décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Jet JWBS-18X devrait contenir:
- informations sur les caractéristiques techniques du dispositif Jet JWBS-18X
- nom du fabricant et année de fabrication Jet JWBS-18X
- instructions d'utilisation, de réglage et d’entretien de l'équipement Jet JWBS-18X
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Jet JWBS-18X ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Jet JWBS-18X et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Jet en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Jet JWBS-18X, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Jet JWBS-18X, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Jet JWBS-18X. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Operating Instructions and Parts Manual 18” Band Saw Models: JWBS-18X, JWBS-18X-3 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-710750 Ph.: 800-274-6848 Revision B 5/05 www.wmhtoolgroup.com Copyright © WMH Tool Group This Manual is Bookmarked[...]

  • Page 2

    2 This manual has been pre pared for the owner an d o perators of JET JWBS-18X and JWBS-18X-3 Band Saws. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and effi ciency from your ban d saw and to aid in using it safely, please read this manual thoroug hl y a[...]

  • Page 3

    3 Table of Contents Warranty ....................................................................................................................... ................................. 2 Table of Contents .............................................................................................................. ............................ 3 Warni[...]

  • Page 4

    4 Warning 1. Read and understand the entire o wner's manual before attemptin g assembly or operation. 2. Rea d and understand the warnings posted on the mach ine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. This band saw is desi[...]

  • Page 5

    5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Looking ar ound, carrying on a conversatio n and “horse-play” are careless acts that can result in serious inj ury. 22. Maintain a balanced stance at all times so that you do not fall or lean a [...]

  • Page 6

    6 Introduction This manual is provided by Jet covering the safe operation and maintenance pro cedures for models JWBS-18X and JWBS-18 X-3 Band Saws. This manual c ontains in structions on installation, safety precautions, general o perating procedures, mainten ance instructions a nd parts breakd own. This machine has been designed and constru cted [...]

  • Page 7

    7 Grounding Instructions 1.75 HP Single Phase Motor This machine must be grounded while in use to protect the opera tor from electric shock. In the event of a malfunction or br eakdown, grounding provides a path of least resistance fo r electric current to reduce the risk of electric shock. This tool is eq uipped with an electric cord having an equ[...]

  • Page 8

    8 Grounding Instructions 3 HP Single Phase Motor Electrical connections must be made by a qualified electri cian in compliance with all relevant codes. This machine must be properly grounded to help prevent electrical shock and possible fatal injury. This machine must be grounde d. In the event of a malfunction or breakdown, grounding provides a pa[...]

  • Page 9

    9 Unpacking Contents of Shipping Container 1 Band Saw 1 Table 1 Fence and Rail Assembly 1 Resaw Guide and Knob 1 Miter Gauge 1 Owner’s Manual 1 Warranty Card 1 Accessory Package Contains: Hardware Bag 2 Knobs 1 Handle 1 10/12mm Wrench Fence Hardware Bag 4 Hex Cap Screws 4 Flat Washers 4 Lock Washers Rail Hardware Bag 9 Hex Cap Screws 9 Flat Washe[...]

  • Page 10

    10 Assembly Handwheel Attach the handle (A, Fig. 3) to the handwheel (B, Fig. 3). Mounting the Table Important : The table is heavy. Mounting with the help of another person is recommended . Referring to Figures 4 and 5: 1. Remove the table insert (A) and tapered pin (B). 2. Slide the table so the saw blade (D) passe s through the slot where the ta[...]

  • Page 11

    11 Fence Assembly and Adjustment Assembling the Fence to Fence Bod y Referring to Figure 7: 1. Attach the fence (A) to the fence body (B) with four 5/16” x 3/4” hex cap scre ws (C), four 5/16” lock washers (D), and four 5/16” flat washers (E). Hand-tighten only at this time. Assembling the Rear Hook Referring to Figure 8: 2. Thread a 1/4&qu[...]

  • Page 12

    12 Fence Adjustment 5. Place the fence assembly onto the guide rail (D, Fig. 9) and against the edge of the miter slot (C, Fig. 9). The hook at the rear of the fence should fit under the rear rail (see Figure 12). The fence must align parallel to the miter slot along the entire length of the fence. If adjustment is necessary: 6. Lock the fence by p[...]

  • Page 13

    13 Adjusting Clearance betwe en Fence and Table Referring to Figures 11 and 12: Check the clearance between the table and the fence. The fence should not rub against the table surface but be slightly above it. This gap should be the same at the front of the table as it is at the rear. If the gap between fence and table i s not consistent, loosen ei[...]

  • Page 14

    14 Adjustments Table Tilt 1. Disconnect machine from powe r source. 2. Loosen the lock knobs (G, Fig. 14). 3. Tilt table up to 45 degre es to the right, or up to 10 degrees to the left. 4. Tighten the lock knobs. Note : Table stop bolt (F, Fig. 14) must be removed to tilt table to the left. Adjusting 90 Degree Table Stop Blade tension must be prope[...]

  • Page 15

    15 Installing/Changing Blades Disconnect machine from power source. Blade teeth are sh arp, use care when handling the blade. Failure to comply may cause serious injury. 1. Disconnect machine from powe r source. 2. Decrease blade tension by rotating the blad e tension handwheel (A, Fig. 17) according to the arrow direction in until the handwh eel s[...]

  • Page 16

    16 Blade Tension Blade tension is set with the blade tension handwheel (A, Fig. 19) and is perform ed following blade replacement and periodi cally as the blade stretches from use. Disconnect machine from power source before making any adjustments. Referring to Figure 19: 1. Set the blade tension by rotating the handwheel according to the arrow di [...]

  • Page 17

    17 Overview – Bear ing Adjustments Thrust (back support) be aring are located behind the saw blade and provid e support to the back of the blade when the saw is in operation. Guide bearings are located on either side of the saw blade and provide sta bility for the blade when the saw is in operation. These bearings rotate on an eccentric shaft so [...]

  • Page 18

    18 Lower Bearing Adjustments Unplug the machine fro m power source before making any adjustments! Blade teeth are sharp - use care when working near the saw blade. Failure to comply may cause serious injury. Note: Blade tension must be p roperly adjusted prior to bearing guide setup. Refer to the Adjusting Blade Tension section. Referring to Figure[...]

  • Page 19

    19 Blade Lead Blade drift (also known as lead or fence drift ) is a problem that may occur when the bl ade begins to wander off the cutting line even when th e band saw fence is being used. Figure 24 shows an example of blade lead. Blade lead can be caused by a number of factors, and these should all be checked and corrected if necessary:  Fence[...]

  • Page 20

    20 Replacing the V-Belt Disconnect machine from power source before making any adjustments. 1. Release blade tension as describ ed in the Blade Tension section. 2. Release belt tension by loosening the two h ex cap screws (A, B, Fig. 25). The pivot bolt (B) is not visible. 3. Raise the motor and place a block of wood under the motor to take the ten[...]

  • Page 21

    21 the motor. The weight of the motor should p ut enough tension on the belt. You ju st want to push down lightly to take up any slack. 3. Tighten the two hex cap screws (A , B). Note: A new belt may stretch slightly during the “breaking in” process, and the tensio n may occasionally need to be checked a nd adjusted. Pulley Alignment The pulley[...]

  • Page 22

    22 Operation General Procedure 1. Make sure the blade and upper and lower bearings are properly adj usted for tension and tracking. 2. Adjust blade guide a ssembly so that the guide bearings are just above the workpi ece (about 3/16”) allowing mini mum exposure to the blade. See Figure 30. 3. If using the fence, move it into position and lock it [...]

  • Page 23

    23 Resawing Resawing is the process of slicing stock to reduce its thickness, o r to produce boards that are thinner than the original workpiece. Figure 33 demonstrates resa wing. The ideal blade for resawing is the widest one the machine can handle, as the wider the blade the better it can hold a straight line. When resawing thin stock, use a push[...]

  • Page 24

    24 Set The term "set" refers to the way in which the saw teeth are bent or po sitioned. Set patterns are usually selected depending on the type of material that needs to be cut. Three co mmon set patterns are shown in Figure 36. Generally, the Raker set is used for cutting metal workpieces; the Wave set, when the thickness of the workpiec[...]

  • Page 25

    25 Blade Selection Guide Identify the material and thickness of your workpi ece. The chart will show the recommended PITCH, blade TYPE, and FEED RATE. Key: H – Hook L – Low S – Skip M – Medium R – Regular H – High Example: 10/H/M means 10 teeth per inch / Hook Ty pe Blade / Medium Feed Study the part drawing or prototype, o r actually m[...]

  • Page 26

    26 Troubleshooting Trouble Probable Cause Remedy Saw unplugged Check plug connection s Fuse blown, or circuit breaker tri pped Replace fuse, or reset ci rcuit breaker Saw stops or will not start Cord damaged Replace cord Stop not adjusted correctly Check blade with square a nd adjust stop Angle pointer not set accurately Check blade with square a n[...]

  • Page 27

    27 Optional Accessories: Band Saw Blades Stock No. Material Length Width Thickness Type TPI 710030 ...... Carbon Steel ........... 137” ........ 1/4” ........... 0.025” .......... Skip ................ 6 710031 ...... Carbon Steel ........... 137” ........ 3/8” ........... 0.025” .......... Skip ................ 4 710032 ...... Carbon S[...]

  • Page 28

    28 Parts List: Upper Wheel Assembly Index No. Part No. Description Size Qty 1 .......... JWBS18DX-101 ................ Sa w Body......................................................... 1.75HP ................. ..... 1 ............ JWBS18DX-101A.............. Sa w Body ......................................................... 3HP ..................[...]

  • Page 29

    29 Upper Wheel Assembly[...]

  • Page 30

    30 Parts List: Lower Wheel and Motor Assembl y Index No. Part No. Description Size Qty 1 .......... JWBS18-201 ..................... Bearing Base ................................................... ...................... ............ 1 2 .......... JWBS20-62 ....................... Adjusting Bolt ................................................... [...]

  • Page 31

    31 52 ........ TS-1550031 ...................... Flat Washer ..................................................... M5 ................... .......... 2 53 ........ TS-0560071 ...................... Hex Nut ............................................................ #10-24 ............ ........... 2 54 ........ JWBS18DX-254 ................ Plas tic[...]

  • Page 32

    32 Parts List: Blade Guide Assembly Index No. Part No. Description Size Qty 1 .......... TS-0051051 ...................... Hex Cap Screw ................................................ 5/16-18 x 1 ............ .... 4 2 .......... TS-0720081 ...................... Lock Washer .................................................... 5/16 ...............[...]

  • Page 33

    33 Parts List: Blade Guide Assembly Index No. Part No. Description Size Qty 57 ........ JWBS18DX-357 ................ Bearing Brack et ............................................... ........................... ....... 1 58 ........ 6295293 ............................ Locking Handle ................................................ ................[...]

  • Page 34

    34 Blade Guide Assembly[...]

  • Page 35

    35 Parts List: Table and Fence Assembly Index No. Part No. Description Size Qty 1 .......... JWBS18-401 ..................... Lock Handle ..................................................... ..................... ............. 1 2 .......... TS-0680021 ...................... Flat Washer ..................................................... 1/4 ...[...]

  • Page 36

    36 Parts List: Table and Fence Assembly Index No. Part No. Description Size Qty 57 ........ TS-0051091 ...................... Hex Cap Screw ................................................ 5/16”-18x2” ............. .. 2 58 ........ 40-0260 ............................. Wrench ............................................................ ........[...]

  • Page 37

    37 Table and Fence Assembly[...]

  • Page 38

    38 Electrical Connections 1.75HP, 1 Phase[...]

  • Page 39

    39 3HP, 1 Phase[...]

  • Page 40

    40 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m[...]