Jonsered GR 2032D manuel d'utilisation

Read through the Operator's Manual carefully and understand the content before using the machine. Operator´s manual (EP A)[...]

2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine. U se anti-slip and stable boots. Always wear [...]

English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment ............................................. 4 The[...]

4 – English The machine ‘ s saf ety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (S ee the chapter “What is what“ to locate where this equipment is positioned on your machine.) Personal protective equipment SAFETY INST[...]

English – 5 2. Stop switch The stop switch should be used to stop the engine. 3. Cutting attachment guard This guard is intended to prevent objects from being thrown to wards the operator and to protect the operator from unintentionel contact with the cutting attachment. 4. Anti-vibration system Y our machine is equipped with an anti-vibration sy[...]

6 – English SAFETY INSTR UCTIONS 6. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine ‘ s exhaust fumes away from the operator . Muffler fitted with catalytic converter is also designed to reduce harmful exhaust components. In countries that have a warm and dry climate the risk of fire is obvious. [...]

English – 7 SAFETY INSTR UCTIONS 1. Throttle trigger lock • Check that the throttle is locked in the “ idling position “ when the throttle trigger lock is in its original position. • Press in the throttle trigger lock and make sure it returns to its original position when released. • Ensure that the throttle and throttle trigger lock mo[...]

8 – English SAFETY INSTR UCTIONS 3. Cutting attachment guard • Check that the guard is undamaged and not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . 5. Muffler 1. Never use a machine that has a defective muffler.[...]

English – 9 7. Quick-release • Check that the harness straps are correctly positioned. When the harness and machine are adjusted, check the harness ‘ safety release catch to ensure it works correctly. SAFETY INSTR UCTIONS 6. Cutting equipment This section describes how through corr ect maintenance and through using the right type of cutting e[...]

10 – English SAFETY INSTR UCTIONS Cutting equipment Sharpening the grass blade • See the cutting equipment ’ s packaging for correct filing instructions. • The blades are sharpened using a single cut flat file. • Sharpen all edges equally to maintain the balance of the blade. Trimmer head • Only use a trimmer head and trimmer cord that [...]

English – 11 SAFETY INSTR UCTIONS General safety instructions IMPORT ANT INFORMA TION • The machine is only designed for trimming grass, brush cutting and/or forestry clearing. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “ T echnical data “ . • Never use the [...]

12 – English General w orking instructions SAFETY INSTR UCTIONS 4. Take great care when cutting a tree that is subject to tension. A tree that is under tension can spring back to its original position both before and after being cut. Incorrect positioning on your behalf or when positioning the cut can result in the tree hitting you or the machine[...]

English – 13 SAFETY INSTR UCTIONS Adjusting the harness and clearing saw Designations • Forestry clearing is a general term for cutting small trees where each stem is cut individually. A saw blade is used. • Brush cutting is a general term for clearing grass. Grass blades are used for this purpose. • Grass trimming is a general term for lig[...]

14 – English SAFETY INSTR UCTIONS Clearing ‘ s ABC A. Always use the correct equipment. B. Always have well adjusted equipment. C. Follow the safety instructions. D. Organise the work well. E. Always use full throttle when applying the blade. F. Always use a sharp blade. G. Avoid stones. H. Guide the direction of fall (use the wind). ! W ARNING[...]

English – 15 SAFETY INSTR UCTIONS • Large stems must be cut from two sides. Determine in which direction the stem should fall. First apply the saw to the felling side. Then cut from the other side to fell the stem. The feed pressure should be applied with regard to the size of the stem ‘ s hardness. Small stems require more pressure, while la[...]

16 – English SAFETY INSTR UCTIONS Grass clearing using the trimmer head and plastic knifes • Hold the trimmer head just above the ground at an angle. It is the end of the cord that carries out the work. Let the cord work at its own pace. Do not press the cord into the area to be cut. • The cord can easily remove grass and weeds up against wal[...]

English – 17 WHA T IS WHA T? What is what on the brushcutter? 1. Blade 2. Gr ease filler cap 3. Angle gear 4. Blade guard 5. Shaft 6. Handlebars 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. S uspension for clearing saw 11. C ylinder cov er 12. S tarter handle 13. F uel tank 14. Choke 15. Air purge 27 30 29 28 23 24 22 16. Air filter co[...]

18 – English Assembling the handlebars (GR2026D/GR2032D) ASSEMBL Y Assembling the handlebars (GR2036) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars.[...]

English – 19 ASSEMBL Y Assembly of the blade and trimmer head Assembling the blade guard and clearing blade • Fasten the bracket (H) using the four screws (I). • The guard (A) is fitted using 4 screws (L) as set out in the diagram. NOTE! Use the recommended blade guard. • Fit the drive disc (B) on the output axle. • Turn the blade axle un[...]

20 – English ASSEMBL Y Assembling the spray guard and trimmer head A uto 32 (GR2026D/GR2032D) K J I G F I M L A K B C • Fit the guard (A) intended for use with the trimmer head. Secure using the 4 bolts (L) and the support plate (M) as set out in the diagram. • Fit the drive disc (B) on the output axle. • Turn the blade axle until one of th[...]

English – 21 ASSEMBL Y Adjusting the harness and clearing saw ! W ARNING! When working with the c learing saw it should alwa ys be hooked in the harness. If this is not done, you cannot contr ol the clearing saw saf ely and this can result in injury to your self or someone else . Ne ver use a harness with a defective quick release catch. Quick re[...]

22 – English FUEL HANDLING Fuel mixture • Clean around the fuel cap. Contamination in the tank can disrupt operations. • Ensure that the fuel is well mixed by shaking the container before filling the tank. W ARNING! Always pr ovide good ventilation when handling fuel. ! Fuelling ! ! W ARNING! The catalytic con verter muffler gets very hot dur[...]

English – 23 ST ART AND ST OP Contr ol before starting Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Warm engine U se the same starting p[...]

24 – English Carburetor Y our JONSERED pr oduct has been designed and manufactured to specifications that r educe harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. T o ensure that your unit is at peak performance and producing the least amount of harmful emissions after br eak in, have your authorized se[...]

English – 25 Final setting of the idling speed T Adjust the idling speed with the screw T , If it is necessary to readjust. F irst turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter- clockwise until the cutting attachment stops. A correctly adjusted idle speed setting occurs whe[...]

26 – English MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4. Cylinder cover (leads cold air onto the cylinder). Clean the cooling[...]

English – 27 MAINTENANCE Spark plug The condition of the spark plug is affected by: • An incorrect carburetor setting. • An incorrect fuel mixture (too much or faulty oil). • A dirty air filter. These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties. If the machine is low on po wer ,[...]

28 – English MAINTENANCE NO TE: Use only JONSERED r eplacement parts. U se of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Y our warranty does not co ver damage or liability caused by the use of accessories and/or attachments not specifically recommended by JONSERED. Maintenance schedule Bel[...]

English – 29 TECHNICAL D A T A T echnical data Engine Displacement, cu. in/cm 3 C ylinder bore, inch/mm S troke length, inch/mm I dling speed, rpm Recommended max. speed, rpm S peed of output shaft, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler S peed-regulated ignition system gnition system Manufactur er/type of ignition s[...]

30 – English T ype M ulti 255-3 ( ∅ 255 3-teeth) M ulti 275-4 ( ∅ 275 4-teeth) M ulti 300 ( ∅ 300 3-teeth) Grass 275-4 ( ∅ 200 26-teeth) Opti X 200-26 (∅ 200 26-teeth) T ricut ∅ 300 T rimmy SII T rimmy S Fi x e d With bearing TECHNICAL D A T A Approved accessories GR2026D Centre hole in blades Ø 20 mm Threaded blade axle M10 G rass b[...]

English – 31 Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (U.S. Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2001 and later small off-road engine. In U.S. and Canada, new small off-road engines must be designed, built and equipped to meet the federal stri[...]

32 – English 1 Auto 32 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " 15 cm 15 cm[...]

English – 33 1 Poly T rim 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10[...]

34 – English 1 T ap-N-Go Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"[...]

English – 35 1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"[...]

36 – English 1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII[...]

English – 37 ~ 15 cm 6' N ~ 15 cm 6' 502 25 56-01 502 26 04-01 502 25 53-01 502 26 24-01 (x2) 740 43 14-00 502 25 52-01 502 26 01-01 735 31 19-00 729 53 27-71 (x3) 738 21 03-04 502 26 03-01 502 27 07-01 502 26 86-01 1 23 4 T rimmy SII[...]

´*xt=¶5Q¨[...]

English – 39[...]

108 88 42-95 ´*xt=¶5Q¨ 2002W04[...]