Knoll Systems HDP2300 manuel d'utilisation

HDP2300 High Definition Projector PROJEC T OR User ’ s Manual[...]

Copyright This publication, including all photograp hs, illustration s and software, is protect ed under international co py- right laws, with all rights reserved. Neither thi s ma nual, nor any of the material contained herein, may be reproduced without written consent of the autho r. © Copyright 20 10 Disclaimer The information in this document [...]

HDP2300 Users Manual — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector. Keep this manual for future reference. Symbols Used Warning symbols a re used [...]

Preface Projector Installation Notice ¾ Place the projector in a horizontal p osition The tilt angle of the projector should not excee d 15 degrees, nor should the p rojector be installed in any way other than the desktop and ceiling mou nt, ot herwise lamp life could decrease dramatically. ¾ Allow at least 50 cm clearance around th e exhaust ven[...]

Replacing the Lamp Replacing the lamp can b e hazardous if done incorrectly. See Replacing the Proj ection Lamp on page 35 for clear and safe instructions for this procedure. Before replacing the lamp: ¾ Unplug the power cord. ¾ Allow the lamp to cool for about one hour. Cleaning the Projector ¾ Unplug the power cord b efore cleaning. See Cleani[...]

– v – Table of Contents GETTING STARTED .......................................................................................................................................................... 1 P ACKING C HECKLIST .................................................................................................................................[...]

— vi — TROUBLESHOOTING ..................................................................................................................................................... 39 C OMMON PROBLEMS AN D SOLUTIONS ............................................................................................................................... 39 T IPS F[...]

– 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: HDP2300 SERIE S P ROJECTOR WITH LENS CAP R EMOTE CONTR OL (WITH TWO AA BATTERIES) VGA CABLE C OMPONENT CABLE P OWER CORD HDMI CABLE CD-ROM (T HIS U SER ’ S MANUAL ) W ARRANTY C ARD Q UICK S TART G UIDE Contact your dealer[...]

Views of Projector Parts HDP2300 Series Front-right View I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. IR receiver Receives IR si gnal from remote control 8 2. Lens Projection Lens 3. Focus ring Focuses the projected image 4. Zoom ring Enlarges the projected image 18 5. Height adjuster Adjusts level of projector 17 6. Function keys See Top view—On-sc[...]

– 3 – I TEM L ABEL D ESCRIPTIO N S EE PAGE : 9. Horizontal lens shift Adjusts the image position horizontally 19 10. Lens release button Press the releas e button befor e removin g the lens 13 Important: Ventilation openings on the projector allow for good air circulation, which keeps the proje ctor lamp cool. Do not obstruct any of the ventila[...]

Top view—On-screen Display (OSD) buttons and LEDs I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. MENU Opens and e xits OSD menus 2. ▲ (Up cu rsor) / Keystone+ Navigates and changes settings in the OSD Quick Me nu – For Keystone 3. ENTER Enter or c onfirm highlighted OSD m enu item 21 4. BLANK Displays a bl ank screen a nd m utes audio 5. ◄ (Left[...]

Rear view I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. VIDEO Connect the co mposite cable from a vi deo devi ce 2. YPbPr Connect a compone nt video e nabled device 3. HDMI 1/ 2/ 3 Connect the HDM I CABLE from a HDMI d evice 4. USB Connect the USB cable from a com puter 12 5. IR receiver Receive IR sign al from rem ote control 8 Red Error code Lamp is [...]

– 6 – I TEM L ABEL D ESCRIPTIO N S EE PAGE : 12. VGA/ SCART/ YPbPr Connects the RGB cable from a computer and component s 13. S-VIDEO Connects the S-Video cable from a video device 12 14. AC IN Connects the power ca ble 13 15. Power switch Turns on/off the proj ector 15 16. 38 17. Kensington Lock Secures to permanent object with a Kensi ngt on?[...]

Bottom view I TEM L ABEL D ESCRIP TION S EE PAGE : 17 1. Tilt adjustor Rotate adju ster lever to adjust angle po sition. 2. Ceiling support ho les Contact your dealer for in formation on mounting the projecto r on a ceiling Note: When installing, ensure that you us e only UL Listed ceiling mounts. For ceiling installations, use approved mounting ha[...]

Remote Control Functions Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the re mote control and the proj ector. If the path be- tween the remote control and the projector is obs tructe[...]

– 9 – I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Power OFF Turns the projector off 13 2. HDMI 2 Displays the HDM I 2 source selection 3. S-VIDEO Displays the S-VIDEO source selection 4. VIDEO Displays the VIDEO source se lection 5. Up cursor / Keystone+ Navigates and changes settings in the OSD Quick Me nu – For Keystone 6. ENTER Enters and co[...]

– 10 – Remote Control Operating Range The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 f[...]

S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 2. Insert the battery with the positive side facing up. 3. Replace the cover. Caution: 1. Only use AA batteries (Alkali ne batteries are recommended). 2. Dispose of used batteries accordi ng to loc[...]

Connecting Input Devices A PC or note book computer and video devices can be connected to the projector a t the same time. Video devices include DVD , VCD, and VHS players, as we ll as mo vie camcor ders and digita l still c ameras. Check the user manu al of the conne cting device to confirm it has the appropr iate output connector. I TEM L ABEL D [...]

Installing or Removing the Optional Lens Caution: y Do not shake or place excessive pressure on t he projector or the lens components as the projec- tor and lens components c ontain precision parts. y Before removing or installing the lens, be sure to turn off the projector, wa it until the cooling fans stop, and turn off the main power switch. y D[...]

Installing the New Lens 1. Align the notches and correctly position the electrical contact pad as shown in the picture. – 14 – Note: Pin of IRIS should be in the direction as shown in the picture. 2. Rotate the lens clockwise until you feel it click into place. HDP2300 Users Manual[...]

Starting and Shutting down t he Projec tor Starting the projector 1. Remove the lens cap. 2. Securely connect the power cord and signal cable. When connected, the power led will turn red. 3. Turn on the lamp by pressing “ ” button on the rear of the projector or “ ” on the remote control. The PWR LED will now flash green. The startup screen[...]

5. Turn on your source that you want to display on the screen (computer, note- book, video player, etc). The projector will detect the source automatically and will display on the screen. If not, push menu button and go to “SYSTEM SETUP: Basic”. Note: If you connected multiple sources at the same time, press the “Source” key on the remote c[...]

Adjusting the Project or Level Take note of the following when setting up the projector: • The projector t able or stand should b e level and sturdy . • Position the projector so that it is perpendicular t o the screen. • Re move the Back Foot Holder on the rear adjuster foot before adjusting the projection angle. • Ensure the cables are in[...]

– 18 – Adjusting Projected Imag e Position Using Shift The Shift feature provides a lens shift function that can be used to adjust the position of the projected image either horizontally or vertica lly within the range detailed below. Shift is a unique system that provid es lens shift while maintaining a much higher ANSI contrast ratio than tra[...]

– 19 – Adjusting the horizontal image position With the lens in the center posit ion the horizontal image pos ition can be adjusted to the left or right by up to a maximum of 10% of the half image width. Note that the maximum horizontal image height ad- justment can be limited by the vertical image position. For example it is not possible to ac[...]

Adjusting the Zoom ring, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size. 2. Use the Image-focus control (on the projector only) to sharpen the pro- jected image. 3. Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bott[...]

O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote control curs or buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illu stration shows the corresp[...]

Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SYSTEM SETUP: Basic . 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the language you want is selected. 4. Press the MENU button to clo[...]

OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting. – 23 – HDP2300 Users Manual[...]

PICTURE: Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE: Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE: Basic menu. Press ◄► to change values for settings. Note: Customizeing the settings in PICTURE: Basic menu is only available in User 1/ 2/ 3 mode. I[...]

PICTURE: Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE: Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE: Advanced menu. Press ◄► to change values for settings. I TEM D ESCRIPTIO N Noise Reduction Press the cursor ◄► button to adjust the Noise [...]

HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu. I TEM D ESCRIPTIO N Press the ◄► buttons to set the Primary Color. Notes: There are six s ets ( R / G/ B/ C/ M/ Y) of colors to be custom ized. Primary Color Hue Press the ◄► buttons to adjust the Hue. Saturation Press the ◄► buttons to adjust the Saturation. Ga[...]

DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings. I TEM D ESCRIPTIO N Press the cursor ◄► button to set the Aspect Ratio. (Range: Auto / 16:9/ 4: 3/ Letter Box/ Re[...]

PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected. I TEM D ESCRIPTIO N Press the ENTER/AU TO button on the control panel o r the ENTER/AUT O button on the remote contr ol to autom atically[...]

SYSTEM SETUP: Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SYSTEM SETUP: Basic menu. Press the cursor ▲▼ button to move up and down in the SYSTEM SETUP: Basic menu. Press ◄► to change values for settings. I TEM D ESCRIPTIO N Press the cursor ◄► buttons to select a different l ocali[...]

Menu Settings Press the ENTER button to enter the Menu Settings sub menu. I TEM D ESCRIPTIO N Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center / Bottom-Left/ Bottom-Right. Menu Position Press the ◄► buttons to set the Menu Display timer before the OSD times out. (Range: 5sec/ 10sec/ 15sec / 20sec/ 25sec/ 3[...]

SYSTEM SETUP: Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SYSTEM SETUP: Advanced menu. Press the cursor ▲▼ button to move up and down in the SYSTEM SETUP: Advanced menu. I TEM D ESCRIPTIO N Lamp Press the ENTE R bu tton to enter the Lamp sub menu. See Lamp on pa ge 32 . HDMI Pr e s s t[...]

– 32 – Lamp Press the ENTER button to enter the Lamp sub menu. I TEM D ESCRIPTIO N Lamp Mode Press the ◄► but tons to a djust l amp bright ness. Reset Lamp Timer Press the ENTER button to reset the Lamp Hour after the lamp is replaced. Lamp Hour Displays the number of hours th e lamp has been in use. HDMI Press the ENTER button to enter the[...]

Closed Caption Press the ENTER button to enter the Closed Caption sub menu. I TEM D ESCRIPTIO N Closed Caption En able Press the ◄► but tons to t urn on or off C losed C aption . Caption Version Press the ◄► buttons to select the Caption Version. 12V OUT A Set 12V OUT A to On to enable the projector to automatica lly lower the projection sc[...]

INFORMATION Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the INFORMATION Menu . I TEM D ESCRIPTIO N Source Displays the activated input source. Resolution Displays the native resolu tion of input source. Lamp Hour Displays the number of hours the lamp has been in use. Firmware Vers ion Displays the fi r[...]

M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this produc t contains a small amount of mercury. b. Do not dispose this product with [...]

6. Use a screwdriver to remove the screws from the lamp module. 7. Pull out the lamp module. 8. Reverse steps 1 to 7 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be connected properly bef[...]

– 37 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilat[...]

Using the Physical Lock ® Using the Kensington – 38 – Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensi ngton security cable. The security lock corresponds to Kensington’s Micr oSaver Securi[...]

T ROUBLE SHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose con- nection. Check the following bef[...]

– 40 – LED Error Messages E RROR C ODE M ESSAGES P OWER LED B LINK R EADY LED B LINK T EMP LED B LINK Lamp Ready ON ON OFF Start ON OFF OFF Cooling ON FLASHING OFF Over temperature OFF OFF ON Thermal Break Sensor error 4 4 OFF Lamp End of l amp life detect ed 5 3 OFF Burner Fan er ror 6 1 OFF Lamp Fan erro r 6 2 OFF Power Fan error 6 3 OFF DMD [...]

– 41 – Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and power up a gain in the correct order. Problem: The image is blurred 1. Adjus t the Focus on the projector. 2. Press the Auto button on the remote control or pr ojector. 3. Ensure the projector-to-scr[...]

– 42 – Remote Control Pr oblems Problem: The projector does not respond to the remote control 1. Direct the remote control towards remote sensor on the project or. 2. Ensure the path between remote and sensor is not obstructed. 3. Turn off any fluores cent lights in the room. 4. Check the b attery polarity. 5. Replace the batteries. 6. Turn off[...]

– 43 – HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announ ced that cables would be tested as Standard or High- Speed cables. ․ Standard (or “category 1”) HDMI cables have be en tested to perfo rm at speeds of 75Mhz o r up to 2.25Gbps, which i[...]

— 44 — S PECIFICATIO NS Model H DP2300 Series Display type TI DLP DMD 0.65” Native Resolution 1920 x 1080 Weight 8.8 kg ( 19 lbs) Lens type Standard Long Short Projection distance 1.5 meters ~ 7 meters 2.meters ~ 20 meters 0.5 meters ~ 3 meter s Projection screen size 37" ~ 300" 31.2" ~ 468" 29.25" ~ 2 00" Projec[...]

– 45 – Projection Distance vs. Projection Si ze H DP2300 Series Projection Distance and Size Table Standard projection lens: TR: 1.54 ~ 1.93 T EL E W IDE Distance (m) 1.28 3.42 4. 27 8.55 1.36 2. 73 3.41 10.23 Diagonal (“) 30 80 100 200 40 80 100 300 Keystone Corr ection Angle (degree) 9.93 9. 93 9.93 9.93 12.39 12.39 12.39 12.39 Image Heig h[...]

– 46 – The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) VGA 640 x 350 31.5 70.1 — — O O 640 x 350 37.9 85.1 — — O O 720 x 350 31.5 70.0 —[...]

– 47 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) 640 x 480 37.9 72.8 — — O O 800 x 600 35.2 56.3 — — O O 800 x 600 37.9 60.3 — — O O 800 x 600 46.9 75.0 — — O O 1024 x 768 48.4 60.0 — — O O 1024 x 768 56.5 70.1 — — O O VESA 1024 x 768 57.7 72 — ?[...]

– 48 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) 720p 45.0 60.0 O — — O 720p 37.5 50.0 O — — O 1080i 33.8 60.0 O — — O 1080i 28.1 50.0 O — — O 1080p 27 24 O — — O 1080p 28.12 5 25 O — — O 1080p 33.75 30 O — — O 1080p 56.25 50 O — — O HDTV 1[...]

Projector Dimensions – 49 – HDP2300 Users Manual[...]

R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These lim its are designed to provide reasonable protection against harmful interference when the equipm ent is operated in a commercial environment. This equipment generates, u[...]