Konica Minolta MAXXUM 5D manuel d'utilisation

INSTRUCTION MANUAL[...]

2 Q UICK ST ART CHECK LIST QUICK ST ART CHECK LIST The following sections will get you started in enjoying your camera. Attach a lens (p. 18) and the camera strap (p. 19). Adjust the viewfinder diopter if necessary (p. 19). Charge the battery (p. 20) and insert it into the camera (p. 21). Insert a memory card into the camera (p. 24). T urn on the c[...]

Thank you for purchasing this Konica Minolta digital camera. Please take the time to read through this instruction manual so you can enjoy all the features of your new camera. Check the packing list before using this product. If any items are missing, immediately contact your camera dealer . 3 BEFORE YOU BEGIN Konica Minolta is a trademark of Konic[...]

FOR PROPER AND SAFE USE 4 F OR PROPER AND SAFE USE NP-400 LITHIUM-ION BA TTERIES This camera operates on a powerful lithium-ion battery . Misuse or abuse of the lithium- ion battery can cause damage or injury through fire, electric shock, or chemical leakage. Read and understand all warnings before using the battery . DANGER • Do not short, disas[...]

5 GENERAL PRODUCT W ARNINGS AND CAUTIONS W ARNING • Only use the battery specified in this manual. • Only use the specified charger or AC adapter within the voltage range indicated on the unit. An inappropriate adapter or current may cause damage or injury through fire or electric shock. • Only use the charger power cord in the sales region f[...]

6 F OR PROPER AND SAFE USE • Do not use these products in a humid environment, or operate them with wet hands. If liquid enters these products, immediately remove the battery or unplug the product, and discontinue use. The continued use of a product exposed to liquids may cause damage or injury through fire or electric shock. • Do not use these[...]

7 CAUTION • Do not point a photographic lens directly at the sun. If sunlight is focused on an inflam- mable surface, a fire may result. Replace the lens cap when the lens is not in use. • Do not use or store these products in a hot or humid environment such as the glove compartment or trunk of a car . It may damage the camera, charger , and ba[...]

8 T ABLE OF CONTENTS Quick start check list ........................................................................................................2 Before you begin ..............................................................................................................3 For proper and safe use ...............................................[...]

9 Histogram display ................................................................................................35 Deleting single images ........................................................................................36 Changing the playback display ...........................................................................37 Enlarged [...]

10 T ABLE OF CONTENTS White balance ......................................................................................................64 Auto white balance ...................................................................................64 Preset white balance ................................................................................65 [...]

11 Custom menu .................................................................................................................92 AF / Shutter release priority setup ......................................................................93 Focus-hold button setup ......................................................................................[...]

12 T ABLE OF CONTENTS CCD plane ........................................................................................................1 10 Attaching the eyepiece cap................................................................................1 1 1 Viewfinder accessories ..........................................................................[...]

13 Kodak EasyShare software ...............................................................................132 DiMAGE Master Lite..........................................................................................134 T roubleshooting ............................................................................................................13[...]

14 N AMES OF P ARTS * This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Please read the care and storage instructions in the back of this manual (p. 139). CAMERA BODY 2. Control dial 3. Shutter-release button 5. Flash* (p. 31) 8. Strap eyelet (p. 19) NAMES OF P ARTS 10. Remote-control terminal (p.[...]

15 14. Card-slot / USB port / Video-out terminal door (p. 24, 1 15, 101) 22. Menu button 17. Controller & Spot-AF button (p. 47) 12. AE lock button (p. 46) 2. Eyepiece sensors* 13. Access lamp 20. Delete button (p. 36) 19. Playback button (p. 34) 21. Display button (p. 33, 37) 15. Anti-Shake switch (p. 32) 3. V iewfinder* (p. 17) 18. LCD monito[...]

16 N AMES OF P ARTS RECORDING MODE DISPLA Y 8. White-balance panel 2. Flash panel 5. AE lock / battery condition panel 7. Image size / quality panel 9. Frame counter 4. Color mode / Digital Effects Control / Metering / AF area / AF mode / Release priority / Drive mode panel 3. Ev scale 1. Exposure mode / exposure panel 6. Camera-sensitivity / Zone [...]

17 VIEWFINDER Wide focus frame Spot-metering area (p. 59) Spot AF area (p. 47) Local focus areas (p. 57) 1. Flash-compensation indicator (p. 60) 4. Wireless/Remote flash indicator (p. 76) 5. AE lock indicator (p. 46) 9. Ev scale 8. Aperture display 7. Shutter-speed display 10. Frames-remaining counter 1 1. Camera-shake warning (p. 30) 3. High-speed[...]

18 G ETTING UP AND RUNNING GETTING UP AND RUNNING This section covers the preparation of the camera. This includes the changing of batteries, memory cards, and lenses as well as the use of external power supplies. Align the red mounting index on the lens and camera body . Carefully insert the lens into the mount, then turn it clockwise until it cli[...]

1. Pass the tip of the strap through the camera’ s strap eyelet from below . Attach the strap so the tip comes between the strap and the camera. 2. Thread the tip of the strap through the holder ring and the inside of the buckle and pull to tighten. Leave some slack in the camera strap so the tip may be threaded through the buckle easily . 3. Pus[...]

20 G ETTING UP AND RUNNING CHARGING THE BA TTER Y Before the camera can be used, the lithium-ion battery must be charged. Before charging the battery , read the safety warnings on page 4 of this manual. Only recharge the battery with the supplied battery charger . The battery should be recharged before each shooting session. See page 140 for batter[...]

21 INST ALLING AND CHANGING THE BA TTERY 1. Open the battery-chamber door by sliding the battery-chamber release toward the back of the camera. 2. Insert the battery with the battery contacts first. Push the battery into the chamber until the battery latch clicks into place. 3. T o remove a battery , slide the battery latch to the side of the batte[...]

22 G ETTING UP AND RUNNING AC ADAPTER AC-1 1 (SOLD SEP ARA TEL Y) The AC Adapter AC-1 1 allows the camera to be powered from an electrical household outlet. The AC Adapter is recommended when the camera is interfaced with a computer or during periods of heavy use. Open the DC terminal cover from the left. The cover is attached to the body to preven[...]

23 BA TTERY CONDITION INDICA TOR Full-battery indicator - the battery is fully charged. Low-battery indicator - battery power is low . Recharge the battery . AUTO POWER SA VE T o conserve battery power , the camera shuts down if an operation is not made within three minutes. T o restore power , press the shutter-release button partway down. The len[...]

24 G ETTING UP AND RUNNING INSERTING AND CHANGING A MEMORY CARD A memory card must be inserted for the camera to operate. If a card has not been inserted, “----” is displayed in the frame counter . T ype I and II CompactFlash cards and Microdrives are compatible with this camera. Always turn off the camera and confirm the access lamp is not lit[...]

25 If the “Unable to use card, Format?” message appears, the card should be formatted with the camera. Use the right/left keys of the controller to highlight the yes button. Press the central button of the controller to format the card; this can take several minutes depending on the card. When a card is formatted, all the data on the card is pe[...]

26 G ETTING UP AND RUNNING SETTING THE DA TE AND TIME After initially inserting a memory card and battery , a message opens requesting that camera’s clock and calendar be set. Images are recorded with the date and time of capture. Depending on the region, the menu language may also have to be set. T o change the language, see the setup menu secti[...]

27 SETTING THE CAMERA TO RECORD IMAGES AUTOMA TICALL Y T urn the exposure dial to the auto or program (P) position. The camera controls are automatic. Auto acts like the program mode, except that many of the recording functions are reset each time it is selected, see page 41 for more information. Not all function are available in auto recording suc[...]

28 B ASIC RECORDING BASIC RECORDING OPERA TION Place the subject within the focus frame. The subject must be within the focus range of the lens. If using a zoom lens, change the focal length to frame the subject. Press the shutter release button partway down to activate the autofocus and autoexposure systems (1). The viewfinder focus signal (A) con[...]

29 FOCUS SIGNALS SPECIAL FOCUSING SITUA TIONS The camera may not be able to focus in certain situations. Use focus lock or manual focus. The subject in the focus frame is low in contrast. The subject is composed of repeating vertical lines. T wo subjects at different distances overlap in the focus frame. The subject is near a very bright object or [...]

30 B ASIC RECORDING FOCUS LOCK The focus-lock function is used when the subject is off- center and outside the focus frame. Focus lock may also be used when a special focusing situation prevents the camera from focusing on the subject. Place the subject within the focus frame. Press and hold the shutter-release button partway down (1). The focus si[...]

31 If the flash signal does not blink after taking the picture, the subject was not within the flash range. The flash range depends on the aperture used for the exposure. The follow chart shows the range when camera sensitivity is set to auto (auto recording) or ISO 100 (program). See page 55 for the flash range with other camera sensitivity settin[...]

32 B ASIC RECORDING ANTI-SHAKE SYSTEM Anti-shake switch Anti-shake scale The Anti-Shake system minimizes the affect of camera shake, a slight blurring caused by subtle hand motion. Camera shake is more pronounced at long focal lengths than short ones. Anti-Shake is less effective with moving subjects or when the camera is panned, with shutter speed[...]

33 DISPLA Y BUTTON Press the display button to switch the monitor display among full, basic, and off. For more on the full display , see page 16. 1. Exposure mode (p. 39) 14. Camera-sensitivity display (p. 55) 9. White-balance display (p. 64) 7. AF area display (p. 57) 12. Battery condition indicator (p. 23) 8. Frame counter (p. 73) 4. Image-size d[...]

34 B ASIC PLA YBACK Images can be viewed in the playback mode. This section covers the basic playback functions. The playback mode has additional menu functions, see page 82. BASIC PLA YBACK The left/right keys of the controller and the control dial display the recorded images. VIEWING IMAGES Press the playback button to activate the playback mode.[...]

35 T o view the histogram of the displayed image, press the up key . Press the down key to return to single-frame playback. HISTOGRAM DISPLA Y 3. Shutter speed 4. Aperture 15. Date of recording 10. Flash compensation (p. 60) 6. Camera sensitivity (ISO) (p. 54) 14. Folder name - file number (p. 120) 9. Exposure compensation (p. 48) 1. Image size (p.[...]

36 B ASIC PLA YBACK T o delete a displayed image, press the delete button; a confirmation screen opens. The displayed image can be deleted. Once deleted, an image cannot be recovered. Press the controller to execute the command on the confirmation screen. The camera returns to playback mode. DELETING SINGLE IMAGES Use the left/right keys to highlig[...]

37 The display button controls the display format. Each time the button is pressed, the display cycles through to the next format: full display , image only , index playback. The index display can be changed in section 1 of the playback menu. Full display Image only CHANGING THE PLA YBACK DISPLA Y In index playback, the four-way keys of the control[...]

38 B ASIC PLA YBACK Enlarge button The controller ’s four-way keys scroll the magnified area. An image can be enlarged for closer examination. The maximum magnification depends on image size from 2.4X for small images to 4.7X for large images. Press the enlarge button to activate enlarged playback. The front control dial browses through the image[...]

39 ADV ANCED RECORDING This section contains detailed information on the camera’s recording functions and operation. Read the sections pertaining to your interest and need. Manual exposure (p. 44) Shutter priority (p. 42) Aperture priority (p. 42) Program exposure (p. 41) Auto recording (p. 41) Portrait The exposure-mode dial is used to select th[...]

40 A DV ANCED RECORDING DIGIT AL SUBJECT PROGRAMS Digital subject programs optimize the camera’s exposure, white-balance, and image-processing systems for specific conditions and subjects. Simply turn the exposure mode dial to select the appropriate subject program. Sports action - used to capture fast action by maximizing shutter speeds. When us[...]

41 AUTO RECORDING Auto recording is set with the exposure-mode dial. Use this exposure mode when wanting fully-automatic exposure control. Auto recording operates like the program exposure mode, except that when the exposure mode dial is turned to the auto-recording position, recording functions are reset to their default settings. Not all function[...]

42 A DV ANCED RECORDING Shutter priority is set with the exposure-mode dial (p. 39). The photographer selects the shutter speed and the camera sets the appropriate aperture to ensure correct exposure. T urn the control dial (1) to adjust the shutter speed between 30 and 1/4000 second in 1/3 Ev increments. The shutter speed is displayed on the monit[...]

43 The shutter speed used for each exposure is displayed on the monitor and in the viewfinder . The following notation is used: The reciprocal is used for shutter speeds from 1/4000 second to 1/3 second. 125 is 1/125 second. For shutter speeds of a half a second or longer , a quote mark is used to denote whole seconds. 1”5 is one and a half secon[...]

44 A DV ANCED RECORDING MANUAL EXPOSURE - M 1. Turn the control dial to change the shutter speed. 2. Press and hold the exposure- compensation button and turn the control dial to change the aperture. The operation to change the aperture and shutter speed can be reversed in section 1 of the custom menu (p. 95). 3. Press and hold the AEL button and t[...]

45 1. Set the appropriate aperture required for the exposure. 2. Decrease the shutter-speed until “BULB” is displayed. 3. T o take the picture, press and hold the shutter-release button for the duration of the exposure. Releasing the shutter button ends the exposure. The monitor is blank during the exposure and remains blank after the exposure [...]

While holding the AEL button, place the subject in the focus frame and press the shutter-release button partway down to focus (2). Press the shutter-release button down all the way to take the picture. The exposure remains locked after the picture is taken if the AEL button is not released. While the exposure is locked, the camera meter is still ac[...]

47 When using flash, pressing the AEL button activates the slow-sync. function; slow sync. is not available in S and M exposure modes. Slow sync. balances the ambient light exposure with the flash exposure so the background is recorded with the subject. When the AEL button is pressed and held, the ambient light exposure is determined and the flash [...]

48 A DV ANCED RECORDING –2.0Ev –1.0Ev Metered camera exposure The exposure is compensated by -1.0Ev . EXPOSURE COMPENSA TION When using auto recording, P , A, and S exposure modes or a digital subject program, the exposure can be compensated. T o compensate the ambient exposure, press and hold the exposure-compensation button and turn the contr[...]

49 AF / MF SWITCH Slide the AM/MF switch to change between autofocus and manual focus. An indicator on the monitor shows the active focus mode. DEPTH-OF-FIELD PREVIEW The aperture controls depth of field; the area in front of the camera that appears in focus. The smaller the aperture, the greater the depth of field. Depth-of-field preview sets the [...]

50 A DV ANCED RECORDING Single-frame and Continuous advance - to take single or multiple images at one time (p. 51). Self-timer - to delay the release of the shutter by 10 or 2 seconds (p. 51). The drive modes control the rate and method of image capture. Single-frame advance is the default drive mode and is described in the basic recording section[...]

51 Continuous-advance mode allows a series of images to be captured while holding down the shutter-release button. The maximum frame rate is 3fps until the camera buf fer memory is full. The frame rate after that depends on the writing speed of the memory card. Five RAW or three RA W + JPEG will fill the camera buf fer memory . The number of JPEG i[...]

52 A DV ANCED RECORDING EXPOSURE BRACKETING NOTES Bracketing is a method of taking a series of images of a static subject in which each image has a slight variation in exposure. Exposure and flash brackets can be made. 0.3 Ev bracket 0.7 Ev bracket Flash bracket: 0.7 Ev Exposure bracket: 0.3 Ev Select continuous-advance bracketing or single-frame a[...]

Compose the picture as described in the basic recording section (p. 28). As the bracket is made, the index marks disappear from the Ev scale to show the remaining frames. When making a continuous-advance bracket, if the shutter button is release before the bracket is completed, the bracket resets. If using continuous AF or Auto AF with moving subje[...]

54 A DV ANCED RECORDING Camera sensitivity can be changed. Zone Matching for high-key or low-key subjects can be activated. The sensitivity setting is displayed on the monitor . Press the camera-sensitivity button (1) to open the setting screen. CAMERA SENSITIVITY (ISO) AND ZONE MA TCHING Camera sensitivity display Use the four-way keys of the cont[...]

An ƒ-number indicates the relative aperture of the lens and lets us determine how much light it lets through. But why does the number get bigger when the amount of light decreases? The answer is in the way it is written, ƒ/2.0, ƒ/8.0. etc. That means the focal length of the lens (ƒ) divide by 2 or 8. So a 100mm lens at ƒ/2 has a 50mm physical [...]

56 A DV ANCED RECORDING AF area, focus mode, metering mode, flash compensation, color mode, and Digital Effects Control are set with the function button. Monitor indicators show active settings. Press the button (1) to open the setting screen. FUNCTION BUTTON Function indicators Options Use the up/down keys of the controller to select the function.[...]

57 AF AREA AF-area modes control which AF areas are used for focus. The modes are selected with the function button (p. 56). The active AF area is indicated on the monitor . Wide AF area - to use the wide focus frames in the viewfinder to focus. See the basic operation section on page 28. Pressing and holding the four- way controller keys also acti[...]

58 A DV ANCED RECORDING AF MODES Single-shot AF (Autofocus), continuous AF , automatic AF , and direct manual focus is set with the function button (p. 56). The AF system activates when the shutter-release button is pressed partway down or with the controller (p. 57). Focus is confirmed with the viewfinder focus signals, see page 29. Single-shot AF[...]

59 METERING MODES The metering mode specifies the metering pattern. The metering mode is set with the function button (p. 56). On the function-selection screen, use the up/down keys of the controller to select the metering modes and the left/right keys to select the specific mode. Press the central button of the controller to complete the operation[...]

60 A DV ANCED RECORDING Positive compensation No compensation Negative compensation No flash FLASH COMPENSA TION The relative output of the flash can be compensated by ± 2.0 Ev with the function button (p. 56). On the function-selection screen, use the up/down keys of the controller to select exposure compensation and the left/right keys to adjust[...]

61 COLOR MODE The color mode controls what the image looks like as well as the color space. The color mode is set with the function button (p. 56). The color mode can only be selected in P , A, S, and M exposure modes. Except for the Abobe RGB and embed Adobe RGB, all color modes use sRGB color space. Some color modes use preset Digital Effects Con[...]

62 A DV ANCED RECORDING Adobe RGB has a larger color gamut than the more common sRGB. The size of the gamut limits the colors that can be reproduced; the larger the gamut, the more colors. If the image will be printed out with a high-quality printer , the use of the Embedded Adobe RGB and Adobe RGB color modes are recommended over the other sRGB co[...]

63 DIGIT AL EFFECTS CONTROL (DEC) The Digital Effects Control can make adjustments to the contrast, color saturation, and sharpness of specific color modes. Some color modes use preset Digital Effects Control values, the default positions are indicated by a thick index mark on the scale. Digital effects are set with the function button (p. 56). On [...]

64 A DV ANCED RECORDING WHITE BALANCE White balance is the camera’s ability to make dif ferent types of lighting appear natural. The active white-balance mode is displayed in the white-balance panel on the monitor . Auto white balance - white balance is set automatically . T urn the white-balance dial to the appropriate position. Preset white bal[...]

65 With the white balance dial in the preset white balance position, press the white-balance button to open the setting screen. PRESET WHITE BALANCE Preset white balance :select :adjust :enter Daylight The up/down controller keys adjust the white balance in seven levels: +3 to –3 (+4 to –2 for fluorescent). Except for fluorescent, the change of[...]

66 A DV ANCED RECORDING Custom-white-balance function allows the camera to be calibrated to a specific lighting condition. With the white balance dial in the custom position, press the white- balance button to open the setting screen. CUSTOM WHITE BALANCE Fill the spot metering area with a white or neutral object; the object does not need to be in [...]

67 A calibration error may occur under extremely bright light sources, especially with flash units. If an error occurs, a message appears on the monitor and the white-balance indicator is yellow . Repeat the procedure by recalibrating using a gray card as a reference target to reduce the intensity of the illumination. White balance can be set to a [...]

68 A SHORT GUIDE TO PHOTOGRAPHY Photography can be a rewarding pursuit. It is a broad and disciplined field that can take years to master . But the pleasure in making photographs and the joy of capturing a magical moment cannot be compared. The guide is an introduction to some basic photographic principles. A SHORT GUIDE TO PHOT OGRAPHY The lens ap[...]

69 LIGHT SOURCES AND COLOR The human eye adapts itself extremely well under different conditions. The paper of this manual you are reading looks white regardless of the type of lighting. Photographic systems are much less flexible. As the light source changes, so does the overall color of a scene - fluorescent office ceiling lights create a green c[...]

Use the left/right keys of the controller to highlight the appropriate menu tab; the menus change as the tabs are highlighted. 70 R ECORDING MENU In recording mode, press the menu button to open and close the menu. The four-way keys of the controller move the cursor in the menu. Pressing the central button of the controller enters a setting. When t[...]

The control dial moves the cursor left and right in the menus. The menu section memory option in section 3 of the setup menu memorizes the last menu section opened and returns to that section when the menu button is pressed (p. 106). Camera Notes Flash mode Fill-flash Flash control ADI flash – Reset Bracket order Image size L: 3008x2000 Quality F[...]

72 R ECORDING MENU Image size and quality are set in section 1 of the recording menu (p. 70). Changes are displayed on the monitor . S S: 1504 X 1000 (Small) Image size affects the number of pixels in each image. The greater the image size, the larger the file size. Choose image size based on the final use of the image - smaller images are more sui[...]

73 Extra fine Fine Standard 584 926 S: 1504 X 1000 Extra fine Fine Standard 1.6MB 850KB 540KB Approximate file sizes. The frame counter indicates the approximate number of images that can be stored on the memory card at the camera’s image quality and size settings. If the settings are changed, the frame counter adjusts accordingly . Because the c[...]

74 R ECORDING MENU INST ANT PLA YBACK During the instant playback period, many of the playback functions are available. The displayed images can be deleted using the delete button (p. 36). An images can be magnified with the enlarge button (p. 38). The information display can be turned off and on with the display button, and the histogram can be di[...]

FLASH MODES The flash mode can be changed in section 2 of the recording menu (p. 70). For the flash to fire, the built-in unit must be manually raised; lower the flash to prevent it from firing. The auto-white-balance setting gives priority to the flash’s color temperature. If another type of white balance is used, priority is given to the active[...]

76 R ECORDING MENU WIRELESS / REMOTE FLASH Wireless/Remote flash allows the camera to control an off-camera Program/Maxxum 5600HS(D) and 3600HS(D) flash unit without the need of a cable. Single or multiple flash units can be placed around the subject to create different lighting ef fects. The camera’s built-in flash fires to control the of f- cam[...]

77 Raise the built-in flash on the camera and position the camera and flash around the subject. See the following page for operating ranges. Make sure no objects come between the camera and flash unit. The flash units can be test fired by pressing the AEL button on the camera. AEL button setup in section 1 of the custom menu should be set to one of[...]

78 R ECORDING MENU WIRELESS/REMOTE CAMERA AND FLASH RANGES Flash-to-subject distance Camera-to-subject distance The camera and flash must be within 5m or 16.4 ft of the subject. Up to sync. speed 1 1/250 second 1.4 ~ 5m / 4.6 ~ 16.4ft 1 ~ 5m / 3.3 ~ 16.4ft 1 ~ 5m / 3.3 ~ 16.4ft 1 ~ 5m / 3.3 ~ 16.4ft 1 ~ 2.5m / 3.3 ~ 8.2ft 1 ~ 5m / 3.3 ~ 16.4ft 1 ~ [...]

79 FLASH CONTROL ADI and pre-flash TTL flash control are available. Flash control is changed in section 2 of the recording menu (p. 70). The flash control used depends on the lens and flash combination. ADI (Advanced Distance Integration) flash metering - combines distance information from D-series lenses with information from a pre-flash exposure.[...]

80 R ECORDING MENU RECORDING MODE RESET The recording mode functions can be reset in section 2 of the recording menu (p. 70). When selected, a confirmation screen appears; choosing “Y es” resets the following functions and settings, “No” cancels the operation. Exposure compensation ± 0.0 p. 48 Flash compensation ± 0.0 p. 60 AF area Wide A[...]

81 The full version of DiMAGE Master gives you all the tools to organize, examine, and process your images. The Organizer window allows you to sort images quickly into four user-defined classifications. Outtakes can easily be hidden from view without the need to delete or remove them from the folder . Is it difficult to decide which image is the be[...]

82 P LA YBACK MENU NA VIGA TING THE PLA YBACK MENU PLA YBACK MENU Use the left/right keys of the controller to highlight the appropriate menu tab; the menus change as the tabs are highlighted. When the required menu section is displayed, use the up/down key to scroll through the menu options. Highlight the option whose setting needs to be changed. [...]

Slide show – – – Off – DPOF set Date imprint Index print Cancel print 83 T o play back images automatically (p. 88) T o select the folder to view in playback (p. 85). T o select images for DPOF printing (p. 89). T o print the date of capture with each print (p. 90) T o create an index print with the DPOF order (p. 90) Delete – Format – [...]

84 P LA YBACK MENU DELETE Deleting permanently erases the image. Once deleted, an image cannot be recovered. Care should be taken when using the delete function. Marked frames - to delete multiple images. When this setting is chosen, the frame- selection screen (p. 83) is displayed. Use the left/right keys of the controller to highlight the first i[...]

Only the images in the folders specified with the view-folder option in section 1 of the playback menu (p. 82) can be viewed or edited in playback. T wo options are available: All folders - to view and edit all images on the memory card. Single folder - to view and edit images in a specific folder . The folder is selected in the folder-name option [...]

86 P LA YBACK MENU LOCK Delete – Format – View folder Lock – Index format 9 frames All folders Folder name 100KM028 Single, multiple, or all images on the memory card or in a folder specified with the view-folder option can be locked. A locked image cannot be deleted by either the playback menu functions or the delete button. Important images[...]

87 INDEX PLA YBACK FORMA T :select folder The index-format option in section 1 of the playback menu can specify a four , nine, and sixteen image display for index playback (p. 37) and frame-selection screens (p. 83). A file browser can also be used in place of the index playback display mode; a 9-frame display is used for the selection screens. 9-f[...]

88 P LA YBACK MENU Section 2 of the playback menu starts the slide-show function. This function automatically displays images every five seconds on the card or in the folder specified with the view-folder option in section 1 of the menu. Highlight “Enter” in the slide-show option in section 2 of the playback menu and press the center of the con[...]

89 The DPOF-set option is used to set an order for standard prints from digital images. Single, multiple, or all images on the memory card or in a folder specified with the view-folder option can be printed (p. 85). DPOF setup has three options: DPOF SETUP Marked frames - to choose a group of images to be printed or when the number of copies for ea[...]

90 P LA YBACK MENU After the pictures have been printed, the DPOF file remains on the memory card and must be canceled manually . The cancel-print option in section 2 of the playback menu deletes the DPOF files. When the setting is selected, a confirmation screen appears; choosing and entering “Y es” executes the operation and cancels the print[...]

The control dial moves the cursor left and right in the menus. The menu section memory option in section 3 of the setup menu memorizes the last menu section opened and returns to that section when the menu button is pressed (p. 106). Image size L: 3008x2000 Quality Fine Inst.Playback 2 sec. Noise reductn On 91 OPENING THE CUSTOM & SETUP MENUS T[...]

92 C USTOM MENU CUSTOM MENU Use the left/right keys of the controller to highlight the appropriate menu tab; the menus change as the tabs are highlighted. When the required menu section is displayed, use the up/down key to scroll through the menu options. Highlight the option whose setting needs to be changed. Press the right controller key to disp[...]

Priority setup AF Focus hold Ambient&flash AF illuminator On AE hold Shutter speed FocusHoldButt. AEL button Ctrl dial set Exp. comp. set 93 T o set AF or shutter-release priority (p. 93). T o set the operation of a lens’ focus-hold button (p. 94). T o set the operation of the AEL button (p. 94). T o specify exposure control with the control [...]

94 C USTOM MENU FOCUS-HOLD BUTTON SETUP The operation of the AEL button (p. 46) can be specified in section 1 of the custom menu (p. 92). This custom function has four options: AE hold - press and hold the AEL button to lock the exposure, release the button to unlock it. The metering mode set is used (p. 59). AE toggle - press and release the AEL b[...]

95 CONTROL-DIAL SETUP The operation of the control dial in the auto recording, program, and manual exposure modes (p. 39) can be specified in section 1 of the custom menu (p. 92). This custom function has two options: Shutter speed - this is the default setting. Descriptions in the manual are based on this. When using program shift (p. 41), P S is [...]

96 C USTOM MENU AF ILLUMINA TOR CARD SHUTTER LOCK The card shutter lock prevents the shutter from releasing when no memory card is inserted in the camera. The shutter lock is turned on and off in section 2 of the custom menu (p. 92). The built-in flash is used as an AF Illuminator . When the scene is too dark for the camera to focus, raise the buil[...]

97 AF AREA SETUP The spot focus or local AF areas are illuminated when the camera focuses. The illumination period is selected in section 2 of the custom menu (p. 92) between 0.3 seconds and 0.6 seconds. AF area illuminator activation can also be turned off. AF area illuminator MONITOR DISPLA Y SETUP Automatic and manual monitor display is selected[...]

The control dial moves the cursor left and right in the menus. Camera Notes 98 S ETUP MENU Use the up/down key to highlight the new setting. If “Enter” is displayed, press the central button of the controller to continue. SETUP MENU Use the left/right keys of the controller to highlight the appropriate menu tab; the menus change as the tabs are[...]

L C D b a c k l i g h t 5 sec. 3 min. – Reset default – Off “No” Power save MenuSec.Memory Delete conf. Clean CCD File # memory Of f Std. form 100KM028 – Folder name Select folder New folder LCDbrightness – Data storage English Date/Time set – NTSC On T ransfer mode Video output Audio signals Language 99 T o set monitor brightness (p.[...]

100 S ETUP MENU LCD BRIGHTNESS Monitor brightness is adjusted in section 1 of the setup menu. Highlight “Enter” and press the central button of the controller to open the LCD brightness setup screen. Brightness is controlled in eleven levels. Use the left/right controller keys to adjust the brightness, the monitor adjusts accordingly . TRANSFER[...]

101 VIDEO OUTPUT Camera images can be displayed on a television. The video output can be changed between NTSC and P AL. North America uses the NTSC standard and Europe uses the P AL standard. Check which standard is used in your region to play back images on your television set. 1. Turn of f the television and the camera. 2. Slide the card-slot doo[...]

Japanese Svenska Russian Korean italiano Chinese (CS) Chinese (CT) English Deutsch Français Español 102 S ETUP MENU LANGUAGE The language used in the menus can be changed. Highlight the current language and press the center of the controller to open the language setup screen. AUDIO SIGNALS When the shutter-release button is pressed partway down, [...]

103 DA TE AND TIME SETUP It is important to accurately set the clock. When a still image is recorded, the date and time of the recording are saved with the image and are displayed during playback or can be read with the DiMAGE Master Lite software. When the Date/T ime-set option is selected and entered in section 1 of the setup menu, the date/time [...]

104 S ETUP MENU FOLDER NAME 100KM028 10150801 (Standard) (Date) SELECT FOLDER This option specifies in which folder images are saved. Only folders with a standard folder name can be selected. If the date folder name option is used, images are placed in a folder with the corresponding date of recording. Select folder is in section 2 of the setup men[...]

105 NEW FOLDER This allows the creation of new folders. The folder-name option in section 2 of the setup menu specifies the folder- name format. If multiple date-format folders are created, only the last folder can be used for storing images. Highlight “Enter” and press the center of the controller to create a new folder . The new folder name i[...]

106 S ETUP MENU MENU SECTION MEMORY The camera can remember which menu section was last opened. If the menu section memory function is on, when the menu button is pressed, the last menu section that was last displayed is opened. When menu section memory is off, section 1 of the recording or playback menu is displayed when the menu button is pressed[...]

107 LCD backlight Enter Reset default Power save MenuSec.Memory Delete conf. Clean CCD LCD backlight Reset default After cleaning CCD, turn camera off. Continue? Ye s No The battery should be fully charged before cleaning the CCD. If battery power is low , this function cannot be used. The use of the optional AC adapter is recommended over the use [...]

108 S ETUP MENU RESET DEF AUL T This option resets all camera modes and menus. When selected, a confirmation screen appears; choosing “Y es” resets the following functions and settings, “No” cancels the operation. Recording and Playback mode Recording menu Recording display Full display p. 33 AF mode AF-A p. 37 p. 50 p. 48 p. 60 p. 57 Camer[...]

109 Playback menu Custom menu Setup menu p. 100 p. 100 p. 102 p. 103 p. 104 p. 105 p. 105 p. 106 p. 106 p. 85 p. 87 p. 90 p. 93 p. 95 p. 95 p. 96 p. 96 p. 96 p. 97 p. 97 p. 97 p. 97 p. 94 p. 94 View folder All folders Index format 9 frame Date imprint Off AF/Shutter-release priority setup AF priority Focus-hold button setup Focus hold AEL button se[...]

110 A CCESSORY NOTES ACCESSOR Y NOTES This section contains operation and compatibility information with camera accessories. Please read it in its entirety to achieve the best results with your camera. LENS SHADOWING Lens shadowing occurs when the lens or lens hood blocks part of the output from the built-in flash. Lens shadowing appears as a semi-[...]

111 The supplied eyepiece cap prevents light from entering through the viewfinder and affecting the exposure meter or fogging the image when using the self-timer or during long exposures. Carefully slide the eyepiece cup from around the viewfinder frame by pushing on each side of the cup. Slide the eyepiece cap over the viewfinder . The cap should [...]

112 A CCESSORY NOTES This camera is compatible with the High Speed Sync. (HSS) function in the Program/Maxxum Flash 5600HS(D) and 3600HS(D). This allows the camera to use its full range of shutter speeds up to 1/4000 second. HSS cannot be used with the 2-second self-timer drive mode nor the rear sync. flash mode. Attach a compatible flash unit to t[...]

113 ABOUT THE BA TTER Y CHARGER CORD The included AC cord is designed for the current of the sales region. Only use the cord in the region it was purchased. China (220-240V) Continental Europe, Korea, Singapore (220-240V) Great Britain, Hong Kong (220V -240V) United States, Canada, Japan, T aiwan (100V -120V) APC-151 APC-150 APC-160 APC-170 Region [...]

114 D ATA - TRANSFER MODE DA T A-TRANSFER MODE Read this section carefully before connecting the camera to a computer . This manual does not cover the basic operation of computers or their operating systems; please refer to the manual supplied with your computer . For the camera to be connected directly to the computer and used as a mass-storage de[...]

115 CONNECTING THE CAMERA TO A COMPUTER 1. Confirm the data-transfer option in section 1 of the setup menu is set to “Data storage” (p. 98). T urn the camera off. 2. Start up the computer . The computer must be on before connecting the camera. 3. Slide the card-slot door toward the back of the camera to release the safety catch and open. Attach[...]

116 D ATA - TRANSFER MODE CONNECTING TO WINDOWS 98 / 98 SECOND EDITION The driver needs only to be installed once. If the driver cannot be installed automatically , it can be installed manually with the operating system’s add-new-hardware wizard; see the instructions on the following page. During installation, if the operating system requests the[...]

117 Choose the recommended search for a suitable driver . Click “Next.” Choose to specify the location of the driver . The browse window can be used to indicate the driver location. The driver should be located in the CD- ROM drive at :Win98USB. When the location is shown in the window , click “Next.” Manual installation T o install the W[...]

118 D ATA - TRANSFER MODE The add new hardware wizard confirms the location of the driver . One of three drivers may be located: MNL VENUM.inf, USBPDR.inf, or USBSTRG.inf. The letter designating the CD-ROM drive varies between computers. Click “Next” to install the driver in the system. The last window confirms the driver has been installed. Cl[...]

119 AUTO POWER SA VE (DA T A-TRANSFER MODE) If the camera does not receive a read or write command within ten minutes, it shuts down to save power . When the camera shuts down, an unsafe-removal-of-device warning may appear on the computer monitor . Click “OK.” Neither the camera or computer will be damaged in this operation. Unplug the USB cab[...]

120 D ATA - TRANSFER MODE MEMORY CARD FOLDER ORGANIZA TION Once the camera is connected to the computer , image files can be accessed by double clicking on icons. Image folders are located in the DCIM folder . T o copy images, simply drag and drop the file icon into a location in the computer . Drive Icon Dcim PICT0002.JPG Extra fine, fine, or stan[...]

121 Image file names begin with “PICT” followed by a four-digit file number and a mrw , jpg, jpe, or thm extension. The thumbnail images (thm) are used in camera and DiMAGE Master Lite operation. If a RA W or JPEG image uses the Adobe RGB color mode without an embedded profile, the file name begins with “_ICT .” When a new folder is created[...]

DISCONNECTING THE CAMERA FROM THE COMPUTER 122 D ATA - TRANSFER MODE Confirm the access lamp is not lit. T urn off the camera and then disconnect the USB cable. If Kodak EasyShare is open, quit the application before disconnecting the camera. Never disconnect the camera when the access lamp is lit - the data or memory card may permanently be damage[...]

123 Confirm that the access lamp is not lit and then drag the mass-storage device icon and drop it into the trash. Disconnect the USB cable. MACINTOSH The hardware devices connected to the system are displayed. Click the display-device-components check box. Highlight the device to be stopped by clicking on it then click “Stop.” A confirmation s[...]

124 D ATA - TRANSFER MODE CHANGING THE MEMOR Y CARD (DA T A-TRANSFER MODE) Care should be taken when changing memory cards while the camera is attached to the computer . Data could be lost or damaged if the camera is not properly disconnected. Always confirm the access lamp is out before removing the memory card. WINDOWS 98 / 98 SECOND EDITION 1. T[...]

125 1. Insert a memory card in the camera and connect it to the computer with the USB cable. Other devices must not be connected to the computer during this procedure. 2. Right click on the My-computer icon. Select “properties” from the drop-down menu. Windows XP: from the start menu go to the control panel. Click on the performance and mainten[...]

126 D ATA - TRANSFER MODE PICTBRIDGE Use the left/right keys of the controller to display the image to be printed. T otal number of prints Number of copies Press the up key to select the number of copies to be printed. T o deselect an image for printing, press the down key until the number of copies reaches zero. A maximum number of fifty images ca[...]

127 The number of prints in the print run are displayed as well as the print parameters selected with the menu. See the menu navigation section for more information (p. 128). Press the central button of the controller to begin printing, or press the menu button to return to the PictBridge screen. Once printing begins, the operation can be canceled [...]

128 D ATA - TRANSFER MODE NA VIGA TING THE PICTBRIDGE MENU Once a setting has been selected, the cursor returns to the menu options and the new setting is displayed. T o return to the PictBridge screen, press the menu button. Read the following sections on information on the menu options. Use the left/right keys of the controller to highlight the a[...]

129 Batch print Batch print in section 1 selects all still images on the memory card for printing. T wo options are available: All-frames - to print all images on the card. A screen opens so the number of copies of each image can be specified. A total number of fifty images can be printed. Reset - to cancel changes made with the batch print option [...]

130 D ATA - TRANSFER MODE Paper size The paper size of the print can be specified in section 2 of the PictBridge menu. The printer-setup option uses the size set with the printer . Layout The layout of the print can be set in section 2 of the PictBridge menu. The printer-setup option uses the layout parameters of the printer . Borderless printing c[...]

131 Print quality The print quality can be set in section 2 of the PictBridge menu. The printer-setup option uses the quality set with the printer . The fine quality can be specified with the camera. Data print Data can be printed with the image in section 2 of the PictBridge menu. The printer-setup option uses the options set with the printer . Th[...]

132 D ATA - TRANSFER MODE The all-in-one digital photography software solution gives you an effortless way to organize, print, and share your pictures. Organize your pictures Kodak EasyShare software automatically organizes your pictures so you can find and view them quickly . Or create custom albums and sort pictures your own way . Create beautifu[...]

133 1. Close all software applications that are open on you computer (including antivirus software). 2. Place the Digital Camera Software CD-ROM into the CD-ROM drive. 3. Install the software: Windows OS-based computer – The launcher appears. Click the install Kodak EasyShare software button to begin the installation routine. If the install windo[...]

134 D ATA - TRANSFER MODE DiMAGE Master Lite is your entrance into digital imaging. Image-processing tools Color , contrast, saturation, and sharpness can be optimized to bring out the best in your images. Advanced RA W image processing for specific model DiMAGE cameras ensures high-quality results. Image information Detailed information on how and[...]

135 For a complete description of DiMAGE Master Lite, refer to the pdf manual on the supplied DiMAGE Instruction Manual CD-ROM. The manual is located in the manual folder on the CD-ROM and organized in language folders. Copy the file to your computer for reference. Adobe Reader is required to open the pdf manual. A copy of this software is included[...]

136 T ROUBLESHOOTING Problem Symptom Cause Solution The camera will not work. Nothing displayed on monitor . The battery is dead. The AC adapter is not connected properly . R echarge batter y (p. 20). Check that the adapter is connected to the camera and a live electrical outlet (p. 22). The section covers minor problems with basic camera operation[...]

137 Pictures are not sharp. Focus signal is blinking. Subject is too close. Make sure the subject is within the focus range of the lens. A special situation is preventing the autofocus system from focusing (p. 29) Use the focus-lock function to focus on an object at the same distance as the subject (p. 30) or use manual focus (p. 49). Pictures are [...]

138 T ROUBLESHOOTING If the camera does not function normally , turn it of f, remove and reinsert the battery , or unplug and reconnect the AC adapter . Always turn the camera of f using the main switch otherwise the memory card may be damaged and camera settings reset. Problem Symptom Cause Solution Shutter speed and/or aperture display blink. Sub[...]

139 CARE AND STORAGE Read this section in its entirety to get the best results from your camera. With proper care, your camera will provide years of service. CAMERA CARE • Do not subject the camera to shock or impact. • T urn off the camera when transporting. • This camera is neither waterproof nor splashproof. Inserting or removing batteries[...]

140 C ARE AND STORAGE OPERA TING TEMPERA TURES AND CONDITIONS • This camera has been designed for use in temperatures from 0°C to 40°C (32°F to 104°F). • Never leave the camera exposed to extreme high temperatures, such as in a car parked in the sun, or to extreme humidity . • When taking the camera from a cold to a warm environment, plac[...]

141 • After initially inserting the battery , do not remove it for twelve hours; the camera can be off during this period. The main battery is used to charge an internal battery , which protects settings when the main battery is removed. • Keep battery and camera charger contacts clean. Dirty contacts can prevent charging. If the contacts becom[...]

142 C ARE AND STORAGE FCC Compliance Statement Declaration on Conformity Responsible Party: Konica Minolta Photo Imaging U.S.A. Inc. Address: 725 Darlington Avenue, Mahwah, NJ 07430 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi- tions: (1) This device may not cause harmful interference, and (2) [...]

143 For EU member states only This symbol means: Do not dispose of this product together with your household waste. Please refer to the information of your local community or contact our dealers regarding the proper handling of end-of-life electric and electronic equipment. Recycling of this product will help to conserve natural resources and preve[...]

144 T ECHNICAL SPECIFICA TIONS TECHNICAL SPECIFICA TIONS Number of effective pixels: 6.1 million CCD: APS-C size (23.5 X 15.7mm ) interline primary-color CCD with a total of 6.3 million pixels Camera sensitivity (ISO): Auto, 100, 200, 400, 800, 1600, 3200 ISO equivalents Aspect ratio: 3:2 A/D conversion: 12 bit Autofocusing system: TTL phase-detect[...]

145 Battery: One Lithium-ion Battery NP-400 Optional power source: AC adapter (AC-1 1) Battery performance (recording): Approx. number of recorded images: 550 frames. Based on the CIP A standard with a NP-400 lithium-ion battery , 512MB CompactFlash card. Dimensions: 130.5 (W) X 92.5 (H) X 66.5 (D) mm 5.14 (W) X 3.64 (H) X 2.62 (D) in Weight: Appro[...]

146 I NDEX Access lamp, 22, 24, 122, 124 Accessories AC adapter , 22 Flash, 79, 1 12, 1 13 Remote cord, 1 1 1 Viewfinder , 59 ADI metering, 79 Adobe RGB, 62, 88, 120, 126 AF areas, 17, 56, 57 AE lock button, 46, 94 AF illuminator , 96 AF / MF switch, 49 AF modes, 56, 58 AF / Shutter release priority , 93 Audio signals, 102 Autofocus, 48, 57, 58, Sp[...]

147 ƒ -number , 55 Focus-area selection, 57 Focus-hold button, 94 Focus lock, 30 Focus signal, 27, 28, 29 Folder Delete, 87 Organization, 120 Name, 85, 104 New , 105 Select, 104 View , 85 Formatting, 25, 85 Frame counter , 16, 73 Frame-selection screen, 83 Frames-remaining counter , 17 High speed sync. (HSS), 1 12 Image size, 72 Image quality , 72[...]

© 2005 Konica Minolta Photo Imaging, Inc. under the Berne Convention and the Universal Copyright Convention. Printed in Malaysia 9222-2186-1 1 MY -A506[...]