Français dropdown-ico

Life Fitness 849 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Life Fitness 849. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Life Fitness 849 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Life Fitness 849 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Life Fitness 849 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Life Fitness 849
- nom du fabricant et année de fabrication Life Fitness 849
- instructions d'utilisation, de réglage et d’entretien de l'équipement Life Fitness 849
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Life Fitness 849 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Life Fitness 849 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Life Fitness en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Life Fitness 849, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Life Fitness 849, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Life Fitness 849. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    8500 3-ST ACK MUL TI-GYM Part # 6965401 8500104 Rev . C Revision: 08/29/01 1 ASSEMBL Y INSTRUCTIONS[...]

  • Page 2

    IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8500 MULTI-GYM. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Rubber mallet or hammer * 3/4” wrench, 9/16” wrench * Ratch[...]

  • Page 3

    3 PA R T # 6617103 6779802 6625502 6624202 6624302 6622903 6623003 6623503 6624502 6622503 6620903 6691803 6692402 6623702 6662203 6662303 6628302 6275302 6523401 6765203 6765303 6769903 6768003 6767903 6769003 6769702 6769803 6772102 6768803 6768503 6769203 6965503 6872502 6771003 6770102 6871702 6768303 6770703 6772201 6772301 6764901 6773101 696[...]

  • Page 4

    4 STEP 1: FIGURE 1 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble the LEG WEIGHT STACK BASE (23) and the PRESS WEIGHT STACK BASE (24) to the BASE (25) using two 1/2 X 3-1/4” BOLTS (95) and two 1/2” LOCK NUTS (85) as shown in FIGURE 1. • Apply two NON-SKID STRIPS (61) to the BASE (25) as shown in FIGURE 1. 1/2 X 3-1/4” 95 24 25 85[...]

  • Page 5

    STEP 2: FIGURE 2 5 • LOOSELY assemble the FRONT UPRIGHT (29) to the BASE (25) using two 1/2 X 3-1/4” BOLTS (95) and two 1/2” LOCK NUTS (85) as shown in FIGURE 2. • LOOSELY assemble the REAR UPRIGHT (1) to the BASE (25) using one 1/2 X 3” BOLT (94), two 1/2” WASHERS (84), and one 1/2” LOCK NUT (85) as shown in FIGURE 2. • LOOSELY ass[...]

  • Page 6

    STEP 3: FIGURE 3 6 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the FLOATING PULLEY STOP (11) and the SEAT SUPPORT (12) to the FRONT UPRIGHT (29) using two 1/2 X 4” BOLTS (96) and two 1/2” LOW HEIGHT LOCK NUTS (86) as shown in FIGURE 3. • SECURELY assemble one 3/8 X 2-3/4” SPRING PIN (62) to the SEAT SUPPORT (12) as shown in F[...]

  • Page 7

    7 STEP 4: FIGURE 4 • SECURELY assemble the BEARING HOUSING (10) and the CENTER PULLEY BRACKET (27) to the FRONT UPRIGHT (29) using two 1/2 X 4” BOLTS (96) and two 1/2” LOW HEIGHT LOCK NUTS (86). • SECURELY assemble a 3/8 X 2-3/4” SPRING PIN (62) to the to the RIGHT & LEFT PEC ARM (6 & 7). See FIGURE 4. • Assemble the RIGHT PEC A[...]

  • Page 8

    STEP 5: 8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble one 3/8 X 2-3/4” SPRING PIN (62) to the WOLFF SLEEVE (14) as shown in FIGURE 5. FIGURE 5 • Assemble one U-PIN (52) to the WOLFF SLEEVE (14) using one 1/2” PAL NUT (73). • Slide one 4” VINYL SLEEVE (59) onto the U-PIN (52) as shown in FIGURE 5. • CAREFULLY slide the WOL[...]

  • Page 9

    9 STEP 6: FIGURE 6 • SECURELY assemble the PRESS BASE (38) to the BASE (25) using two 1/2 X 3” BOLTS (94), two 1/2” WASHERS (84), and two 1/2” LOCK NUTS (85), and to the REAR UPRIGHT (1) using one 1/2 X 3” BOLT (94), one 1/2” WASHER (84), and one 1/2” LOCK NUT (85) as shown in FIGURE 6. • Assemble the SWIVEL PULLEY BRACKET (35) to t[...]

  • Page 10

    STEP 7: FIGURE 7 10 • SECUREL Y assemble the PRESS FRAME (37) to the PRESS BASE (38) using one 1/2” X 3” BOL T (94), two 3/8 X 3” COUNTERSUNK BOL TS (1 15), one 4-1/2” X 8” PLA TE (57), two 1/2” W ASHERS (84), two 3/8” W ASHERS (80), one 1/2” LOCK NUT (85), and two 3/8” LOCK NUTS (82). (NOTE: Make sure 3/8” countersunk bolts a[...]

  • Page 11

    STEP 8: FIGURE 8 11 • Slide two HINGE TABS (76) onto the WOLFF SLEEVE (14) and SECURELY attach PRESS SEAT PAD (100) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). (NOTE: The “hinge” part of the HINGE TAB (76) should face upward as shown in FIGURE 8.) • Slide the RIGHT BACK PAD ANGLE (5) and LEFT BACK PAD ANGLE (4) onto the[...]

  • Page 12

    12 STEP 9: FIGURE 9 • LOOSELY assemble the PRESS ARM ADJUST (36) to the REAR UPRIGHT (1) using two 1” PILLOW BLOCK BEARINGS (49), four 3/8 X 3-1/4” BOLTS (91), four 3/8” WASHERS (80), and four 3/8” LOCK NUTS (82). (NOTE: Assemble PILLOW BLOCKS (49) so the set screws are on the outside, this will allow more adjustment.) See FIGURE 9. • A[...]

  • Page 13

    STEP 10: 13 • SECURELY assemble one 1/2 X 3-1/2” SPRING PIN (63) to the PRESS ARM (8) as shown in FIGURE 10. FIGURE 10 • SECURELY assemble the PRESS ARM (8) to the PRESS ARM ADJUST (36) using one 1/2 X 7-1/2” BOLT (98), two 1/2” WASHERS (84), two 1/2” FLANGE BEARINGS (70), and one 1/2” LOW HEIGHT LOCK NUT (86). (NOTE: SECURELY tighten[...]

  • Page 14

    STEP 11: FIGURE 11 14 • SECURELY assemble the REAR BASE LEG (31) to the LEG FRAME (34) using two 1/2 X 3” BOLTS (94), two 1/2” WASHERS (84), and two 1/2” LOCK NUTS (85) as shown in FIGURE 11. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 12: FIGURE 12 • SECURELY assemble the LEFT & RIGHT LEG EXTENSION HANDLES (16 & 15) to the LEG FRAM[...]

  • Page 15

    STEP 13: FIGURE 13 15 • SECURELY assemble one 2 X 8” PLATE (17) to the LEG SEAT PAD (102) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). See FIGURE 13. STEP 14: • SECURELY assemble the LEG SEAT PAD (102) to the HINGE TABS (76) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). See FIGURE 14. FIGURE 14 80 17 102[...]

  • Page 16

    16 STEP 15: FIGURE 15 • Assemble LEG BACK PAD ADJUST (2) and LEG BACK PAD SUPPORT (3) to the LEG FRAME (34) using one 1/2 X 6-1/2” BOLT (97), two 1/2” FLANGE BEARINGS (70), one 1/2” LOCK NUT (85) as shown in FIGURE 15. (NOTE: Securely tighten, then back nut off 1/4 turn to allow the two parts to rotate freely.) 0 1 2 34 5 6 1/2 1/2 1/2 1/2 [...]

  • Page 17

    STEP 16: 17 FIGURE 16 • SECURELY assemble the LEG BACK PAD (103) to the LEG BACK PAD ADJUST (2) and the LEG BACK PAD SUPPORT (3) using four 3/8 X 3-1/4” BOLTS (91) and four 3/8” WASHERS (80). See FIGURE 16. • SECURELY assemble two 4 X 7” ROLLER PADS (41) to the LEG FRAME (34) using one 19-1/4” TUBE (39) and two 1-5/16” SHAFT COLLARS ([...]

  • Page 18

    18 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 17: FIGURE 17 • SECURELY assemble two 3/8 X 2-3/4” SPRING PINS (62) to the PAD SLEEVES (33) as shown in FIGURE 17. • Assemble four ROLLER PADS (41) to the PAD SLEEVES (33) using four 1-5/16” SHAFT COLLARS (79). SECURELY tighten set screws on SHAFT COLLARS (79). See FIGURE 16. • Slide P AD SLEEV[...]

  • Page 19

    STEP 19: 19 FIGURE 19 • Insert the two GUIDE RODS (19) into the BASE (25) as shown in FIGURE 19. Lubricate the GUIDE RODS (19) with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (47) down over the GUIDE RODS (19). See FIGURE 19. • Using EXTREME CARE slide twenty WEIGHT PLATES (106) down [...]

  • Page 20

    STEP 20: FIGURE 20 20 • Slide the PRESS GUIDE ROD SUPPORT (20) and LEG GUIDE ROD SUPPORT (21) over their respective GUIDE RODS (19) and SECURELY assemble them to the TOP BOOM (30) using two 1/2 X 3-1/4” BOLTS (91) and two 1/2” LOCK NUTS (85) as shown in FIGURE 20. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 21: FIGURE 21 • Slide the 13/16” [...]

  • Page 21

    21 46 44 45 42 43[...]

  • Page 22

    22 STEP 22: FIGURE 22 • SECUREL Y assemble two 4-1/2” PULLEYS (48) into the slots of the T OP BOOM (30) using two 3/8 X 2-3/4” BOL TS (90), four 3/8” FLANGE SP ACERS (69), two 2-7/8” X 2-1/4” CABLE CLIPS (1 16) and two 3/8” LOCK NUTS (82). (NOTE: Loop the cable around each pulley prior to inserting it in the the slot.) 0 1 2 34 5 6 1/[...]

  • Page 23

    23 STEP 26: STEP 25: FIGURE 25 • Route the LA T CABLE (42) around the pulley in FLOA TING PULLEY STOP (1 1) and the FLOA TING PULLEY BRACKET (55) as shown in FIGURE 25. (NOTE: The CABLE CLIPS may need to be loosened.) • SECURELY assemble two 4-1/2” PULLEYS (48) into the slots of the BASE (25) using two 3/8 X 2-3/4” BOLTS (90), four 3/8” F[...]

  • Page 24

    24 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 27: FIGURE 27 FIGURE 28 STEP 28: • LOOSELY assemble two 4-1/2” PULLEYS (48) to the CENTER PULLEY BRACKET (27) using two 3/8 X 2” BOLTS (89), two 2-7/8” CABLE CLIPS (67), two 3/8” WASHERS (80), and two 3/8” LOCK NUTS (82). See FIGURE 28. • Screw the threaded end of the LAT CABLE (42) approxi[...]

  • Page 25

    STEP 29: 25 FIGURE 29 • Assemble one 4-1/2” PULLEY (48) around the PEC DEC CABLE (46) and to the PULLEY BRACKET (26) using one 3/8 X 2” BOL T (89) , two 2-7/8 X 1” CABLE CLIPS (67) and one 3/8” LOCKNUT (82) as shown in FIGURE 29. STEP 30: FIGURE 30 3/8 X 2” 89 48 46 PEC CABLE 82 • Slide the ends of the PEC DEC CABLE (46) into the bush[...]

  • Page 26

    26 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 32: FIGURE 32 • Screw the threaded end of AB CABLE (45) approximately 1” into the end of the PULLEY BRACKET (26) and tighten jam nut se- curely as shown in FIGURE 32. IMPOR T ANT! Make sure the cables are running in the grooves of all pulleys. 3/8 X 2” 89 82 AB CABLE 45 26 • Route the AB CABLE (4[...]

  • Page 27

    27 STEP 33: FIGURE 33 • SECURE the ball end of the PRESS CABLE (44) and two 4-1/2” PULLEYS (48) to the SWIVEL PULLEY BRACKET (35) using two 3/8 X 2” BOL TS (89), four 3/8” W ASHERS (80), and two 3/8” LOCK NUTS (82) as shown in FIGURE 33. (NOTE: Loop the cable ar ound the pulleys prior to inserting it into the SWIVEL PULLEY BRACKET .) • [...]

  • Page 28

    28 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 34: FIGURE 34 • Route the threaded end of the PRESS CABLE (44) around one 4-1/2” PULLEY (48) and SECURELY assemble the pulley to the front slot of the PRESS ARM AD- JUST (36) using one 3/8 X 2-3/4” BOLT (90), two 3/8” FLANGE SPACERS (69), and one 3/8” LOCK NUT (82) as shown in FIGURE 34. (NOTE:[...]

  • Page 29

    STEP 36: 29 FIGURE 36 • SECURE the PRESS CABLE (44) and one 4-1/2” PULLEY (48) to the PRESS GUIDE ROD SUPPOR T (20) using one 3/8 X 2-3/4” BOL T (90), two 3/8” FLANGE SP ACERS (69), one 2-7/8 X 2-1/4” CABLE CLIP (116) and one 3/8” LOCK NUT (82) as shown in FIGURE 36. (NOTE: Loop the cable around the pulleys prior to inserting it into th[...]

  • Page 30

    30 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 38: FIGURE 38 • SECURE the swivel on the LEG CABLE (43) to the tab on the LEG EXT/CURL (32) using one 3/8 X 2” BOL T (89) and one 3/8” LOW HEIGHT LOCK NUT (83) as shown in FIGURE 38. (NOTE: Do not overtighten! Swivel clevis should rotate fr eely .) 8 9 LEG CABLE 43 32 83 LOW HEIGHT DO NOT OVERTIGHT[...]

  • Page 31

    31 FIGURE 39 IMPORTANT! Make sure the cables are running in the grooves of all pulleys. • SECUREL Y assemble one 4-1/2” PULLEY (48) to the horizontal bracket on the LEG FRAME (34) using one 3/8 X 2” BOL T (89), one 3/8” W ASHER (80), one 2-7/8” CABLE CLIP (67), and one 3/8” LOCK NUT (82) as shown in FIGURE 39. (NOTE: Before tightening, [...]

  • Page 32

    32 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 40 FIGURE 41 STEP 41: STEP 40: • Route the threaded end of the LEG CABLE (43) under the leg weight stack and throught the vetical bracket on the LEG WEIGHT STACK BASE (23) as shown in FIGURE 40. 3/8 X 2” 89 43 LEG CABLE 48 23 82 80 • Assemble one 4-1/2” PULLEY to the vertical bracket on the WEI[...]

  • Page 33

    STEP 42: 33 FIGURE 42 LEG CABLE 43 50 53 • Screw the threaded end of the LEG CABLE (43) approximately 1” into the end of the SELECTOR SHAFT (50) of the HEAD PLATE (53) as shown in FIGURE 42. • Insert one WEIGHT STACK PIN (75) into each weight stack on the 8500 GYM as shown in FIGURE 43. FIGURE 43 • If upon completion of assembly, the HEAD P[...]

  • Page 34

    STEP 44: FIGURE 44 34 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the PRESS SHROUD (113-has press exercise placard ) to the PRESS GUIDE ROD SUPPORT (20) and the PRESS WEIGHT STACK BASE (24) using four 3/8” X 1” BOLTS (114) and four 3/8” WASHERS (80). See FIGURE 44. • SECURELY assemble the PEC SHROUD (112-has warning label in [...]

  • Page 35

    35 FIGURE 45 STEP 45: • Attach the LAT BAR (18) to the ball end of lat cable using one 5/16” SNAP LINK (68). • Attach the AB CRUNCH STRAP (110) to the ball end of cable using one 5/16” SNAP LINK (68). • Attach the LOW ROW BAR (51) to the ball end of press cable using two 5/16” SNAP LINKS (68) and one 12 LINK CHAIN (74). Thank you for pu[...]