Lincoln LS (2005) manuel d'utilisation

Introduction 4 Instrument Cluster 10 W arning and control lights 10 Gauges 15 Entertainment Systems 17 AM/FM stereo with in-dash six CD 17 AM/FM stereo cassette with CD 21 Navigation system 26 Climate Controls 89 Electronic automatic temperature control 89 Rear window defroster 96 Lights 98 Headlamps 98 T urn signal control 101 Bulb replacement 102[...]

Seating and Safety Restraints 158 Seating 158 Safety restraints 165 Air bags 178 Child restraints 188 Tires, Wheels and Loading 199 T ire Information 200 Changing tires 204 Lug Nut T orque 209 V ehicle loading 219 T railer towing 223 Recreational towing 223 Driving 224 Starting 224 Brakes 227 T raction control/AdvanceT rac 230 T ransmission operati[...]

Maintenance and Specifications 276 Engine compartment 277 Engine oil 279 Battery 282 Fuel information 290 Air filter(s) 302 Part numbers 303 Refill capacities 304 Lubricant specifications 306 Accessories 31 1 Index 313 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information st[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, i[...]

SPECIAL NOTICES Emission warranty The New V ehicle Limited W arranty includes Bumper -to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance W arranties. For a detailed description of what is covered and wha[...]

• how far (if at all) the driver was depressing the accelerator and/or the brake pedal; • how fast the vehicle was traveling; and • where the driver was positioning the steering wheel. T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event d[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner ’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based Powertrain Malfunctio[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle ’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains[...]

Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and ST ART , or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light[...]

Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and Specifications chapter . Engine coolant temperature: Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Mainten[...]

Low fuel (if equipped): Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is activated. T urns off when the speed control system is deactivated. Low washer fluid (if equipped): Illuminates when the windshield washer fluid is low . Door ajar ([...]

W ARNING CENTER The instrument cluster is equipped with a warning center that will provide the following warning messages: Bulb warning: Displays when one of the exterior front turn/park lamps or rear brake/turn/tail lamps bulb has burned out. Depress the RESET control to return to the T rip odometer display . Park brake ON: Displayed when the park[...]

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “ H ” and “ C ” ). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off [...]

• Optional instrument cluster T rip odometer: Registers the miles (kilometers) of individual journeys. T o reset, depress the RESET control. T o switch the display from T rip A to the T rip B, depress the A/B control. • Standard instrument cluster • Optional instrument cluster T achometer: Indicates the engine speed in revolutions per minute.[...]

AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CD RADIO (IF EQUIPPED) 1. Seek: Press and release SEEK / for previous/next strong station, selection or track. 2. Rewind: In CD mode, press until desired selection is reached. Fast forward: In CD mode, press until desired selection is reached. TEXT : TEXT is only available when equipped with Satel[...]

Occupancy: Press DSP again to change the occupancy mode to optimize sound for ALL SEA TS, DRIVER SEA T or REAR SEA TS. Press SEL to scroll through settings. 4. Mute: Press to MUTE playing media; press again to return to playing media 5. Eject: Press to eject a CD. Press and hold to eject all loaded discs. 6. Bass: Press BASS; then press SEL / to de[...]

T raffic: In FM mode with RDS ON, this feature allows you to hear traffic broadcasts. W ith the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data). T raffic information is not available in most U.S. markets. FIND Program type: In FM mode and with RDS ON, this feature allows you to search [...]

filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Press again to disengage. 13. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. Speed sensitive volume: Radio volume changes automatically and slightly with[...]

to enable Satellite reception is available through your Lincoln dealer . Detailed Satellite instructions are included with the dealer installed kit. Dealer installed satellite kit available only in the continental United States. For information regarding SIRIUS Satellite Radio, please call toll-free 888-539-SIRIUS (888-539-7474) or visit the SIRIUS[...]

T reble: Allows you to increase or decrease the audio system ’ s treble output. Press TREB then press SEL to decrease or increase the treble levels. 4. Balance: Allows you to shift speaker sound between the right and left speakers. Press BAL then press SEL to shift sound to the left or right . Fade: Allows you to shift speaker sound between the f[...]

In CD mode, FF advances the CD within the current track. 9. Mute: Press to mute the playing media. RDS: (Radio Data System): Allows you to access FM stations which are RDS- equipped. Press RDS then SEL to select from: T raffic — Allows you to receive traffic announcements and control their volume level. T raffic information is not available in mo[...]

14. AM/FM/CD: Press AM/FM to select a radio frequency . Press while in tape or CD mode to return to radio mode. Press CD to enter CD mode and to play a CD already in the system. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compac[...]

RADIO RECEPTION FACTORS There are three factors that can effect radio reception: • Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception. • T errain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception. • S[...]

LINCOLN NAVIGATION SYSTEM (IF EQUIPPED) Y our vehicle may be equipped with a Lincoln Navigation System which allows you to listen to the radio, play CDs and also navigate the vehicle using a navigation DVD. THX audio system (if equipped) Y our vehicle may be equipped with the THX 威 certified premium audio system. This system creates optimal acous[...]

1. VOL-PUSH : Press to turn the system ON/OFF . T urn to adjust the audio volume level. 2. AUDIO : Press to enter audio mode and access radio, CD, CDDJ, DVD (if equipped) settings. 3. MAP : Press to enter map mode and view your current vehicle position on the map. Press and hold to obtain additional position information. This will not function with[...]

Initial map display After pressing AGREE to the initial W ARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock (if equipped). Quick Start — How to get going T o play a radio station: 1[...]

T o play a previously loaded CD: 1. Ensure that the vehicle ignition is on. 2. Press AUDIO. 3. Press CD to select a CD which is already loaded. (NO CD will appear in the display if there are no CDs loaded into the system). Use the controls (1 – 6) to select the desired CD. 4. CD will begin to play . T o load CDs: 1. Press CD OPEN CLOSE at the bot[...]

2. Press DEST . The warning screen will appear . After reading, press AGREE. The screen will show a map with your current location. Press DEST again. 3. Select the desired type of destination entry . Y ou may select “ Address ” , “ Point of Interest ” , “ Emergency ” or “ Previous Dest ” from the first screen. Or , press “ Next Pa[...]

4. Press DEST at the bottom of the map screen. 5. Choose the desired route by pressing the NEXT button (if it appears). There can be up to three alternative routes. 6. Press ST ART to begin the navigation guidance. T o adjust the voice guidance volume: 1. Press the MAP hard key . 2. Press “ Nav Menu ” at the bottom left hand corner of the scree[...]

Press VOICE briefly (on your steering wheel controls) and the voice icon appears on the Navigation display . Press REPEA T to hear the previous command repeated from the navigation system. The voice activated command feature will not operate if a map DVD is not inserted into the navigation DVD unit. At any time, you may say these commands to change[...]

Commands that jump over screens: • Current position • Current location • Map While in navigation map mode, the following commands are available: • Zoom in • Zoom out • Minimum scale • Maximum scale • North up • Change to North up • Heading up • Change to heading up • Map direction • Change map direction • Mark this point[...]

• Chinese food • Continental restaurant • Continental food • French restaurant • French food • Italian restaurant • Italian food • Japanese restaurant • Japanese food • Mexican restaurant • Mexican food • Seafood restaurant • Seafood • Other restaurant • Other food • Shopping • Shopping mall • Grocery store • A[...]

• Change to arrow guidance • Change to arrow guide • T urn list guidance • T urn list guide • Change to turn list guidance • Change to turn list guide • Entire route map • Entire route • Route overview • Reroute • Detour • Detour entire route Navigation help commands you may speak at any time: • Help • Map • Destinatio[...]

V olume/power control Press knob to turn the audio system on/off. T urn to raise or lower volume. The levels will be displayed on the screen. T o activate the navigation mode, press MAP or DEST . T o adjust the navigation voice output level, select the NA V MENU button via the map screen. Speed compensated volume (SCV) W ith this feature, radio vol[...]

3. SCV is located in the middle of the screen. Press to turn on. 4. Select setting 1 to 7 or turn off. The recommended level for the speed compensated volume is from level 1 through level 3. When activated, level 1 is the minimum setting and level 7 is the maximum setting. AM/FM select The AM/FM control works in radio, CD and navigation modes. AM/F[...]

Tune adjust Press TUNE to manually move down/up ( / ) the frequency band. In CD mode, press TRACK to select the previous/next ( / ). Scan Press SCAN for a brief sampling of all listenable stations and CD tracks. Press again to disable and remain on the current selection. Preset scan Press PRESET SCAN to scan the stations stored in the memory preset[...]

Starting autoset memory preset 1. Select a frequency band using AM/FM1/FM2. 2. Press AUTO SET . 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last s[...]

Traf fic function Select TRAFFIC for traffic information broadcast from certain stations which will automatically interrupt radio or CD playback at a preset volume level. T raffic information not available in most U.S. markets. Information feature Press INFO to view the frequency , call letters and PTY category of the selected FM station. Note: Not[...]

T o set/change PTY : Ensure that the RDS function is turned on. Press SET PTY to select from the following program types: • All • Classical • Country • Information • Jazz • Religious • Rock • Soft • To p 4 0 Once PTY has been programmed, press SEEK ( / ) or SCAN to initiate a search up or down the frequency . Preset scan and Autos[...]

Sound functions T o access settings for Bass, T reble, Balance, Fade, DSP (Digital Signal Programing), SCV (Speed Compensated V olume), and Occupancy modes: 1. Press AUDIO. 2. Press SOUND. 3. Select from Bass/T reb; Bal/Fade; DSP/SCV . 4. Press +/ — to increase/decrease the levels. Bass : Allows you to increase or decrease the audio system ’ s [...]

Fade : Allows you to adjust the amount of sound emitted from the front and rear speakers. Balance : Allows you to adjust the sound distribution between the right and left speakers. SCV (Speed Compensated V olume): Automatically compensates for road wind and noise. Refer to Speed compensated volume earlier in this chapter . DSP Occupancy mode : Use [...]

Satellite ready capability Y our Lincoln navigation system comes equipped with Satellite ready capability . The kit to enable Satellite reception is available through your Lincoln dealer . Detailed Satellite instructions are included with the dealer installed kit. CD mode CD units are designed to play commercially pressed 4.75 in (12 cm) audio comp[...]

Press CD. CD play will begin where it stopped last. Loading a CD: 1. Press CD OPEN CLOSE on the bezel. REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Entertainment Systems 45[...]

2. The navigation screen will fold down, allowing you access to the in-dash six CD system. 3. Press LOAD and the desired CD slot number . The indicator light will blink slowly at first, then quickly , signaling the system is ready . 4. Insert a disc. 5. T o load more than one disc , press and hold LOAD. This will initiate autoload and will allow yo[...]

Rewind/fast forward in CD mode Press to reverse or advance ( / ) in the current CD track. Scan feature in CD mode Press SCAN to hear a brief sampling of all tracks on the current CD. Press again to disengage and remain with the current track. Shuffle feature in CD mode When in CD (or CDDJ mode), press SHUFFLE to engage the shuffle feature. Press to[...]

Pause In CD mode, press P AUSE to pause the current track. Press again to continue playing. Map mode Map display information T o access the map display , press MAP on the bezel. Once pressed, the current map display will appear on the screen showing the current vehicle location. CD OPEN • CLOSE MENU DEST MAP AUDIO VOL PUSH REVIEW COPY 2005 Lincol[...]

Zoom control When ’ Zoom ’ is pressed, the scale indicator is shown on the screen. The scale markings are: 1/32, 1/16,1/4, 1/8, 1/2, 1, 2, 4, 8, 16, 32, 64, 128 miles. The control can be used in a number of ways: • T ouch and hold one of the arrow buttons for the map to be displayed again at each zoom level. • T ouch one of the arrow button[...]

Route preferences After entering a destination, the Route preferences will appear on the screen showing what is currently selected. Y ou may choose to activate/deactivate selections which the system will factor in when calculating your route. Those options are: • Minimize T ime/Distance • Use Major Roads • Use T oll Roads • Use Ferries Info[...]

Y ou will be able to view the information (if available) as well as choose to store the destination as a memory point by pressing OK. Screen symbols Navigation symbol — Indicates the current vehicle position and points to the direction in which the vehicle is currently traveling. Destination symbol — Indicates the current route destination. Nex[...]

A void areas or points — The “ X ” symbol indicates a point. to be avoided in route calculations. If the avoid point is enlarged to an avoid area, it will appear on the screen as a shaded box. W ay point symbol — Indicates the location of a way point (locations you wish to visit in route to your ultimate destination) on the map. Home positi[...]

Navigation menu T o access the Navigation Menu, press NA V MENU at the bottom of the map screen. Once pressed, the Navigation Menu will display showing the following options: • Route Options/Preferences • Navigation Set Up • Display Options • Stored Locations • On Route Scroll • V oice Guidance/V olume Depending upon whether or not a ro[...]

While driving under route guidance, only follow an instruction when it is safe to do so as the system cannot be aware of changing conditions. Use voice guidance as much as possible, and only view the display when driving conditions permit. Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to [...]

Quick POI (Point of Interest) Allows you to change the Quick POI menu settings. Select the desired Quick POI (Gas, A TM, etc.) and then press ’ List Categories ’ for further categories, or ’ Map Area POIs ’ to show the desired POIs on your current map. Restore system defaults Resets all system user -selectable options to the default (automa[...]

DVD map version Displays the version of the inserted navigation DVD. Refer to Ordering additional map DVDs for further information. Display Options The Display Options screen will allow you make adjustments to the navigation display screen. Y ou can choose from: • Map Mode (Dual or Full) • Guidance Mode (Arrows or T urn list) • Guidance Displ[...]

Stored locations The Stored locations screen will allow you to choose from destinations that have been saved into the navigation system. In this screen, you can select from Memory Points, Special Memory Points, Home, A void Area, Destination and W ay Point, or Previous Destination. Please refer to the Destination menu section for a complete descrip[...]

V oice guidance/volume Allows you to turn the voice guidance option on/off and to determine the volume level of the guidance voice prompts. T o adjust: 1. Press the MAP hard key . 2. Press “ Nav Menu ” at the bottom left hand corner of the screen. 3. Press the speaker icon to turn the voice guidance option on/off. Press the desired number to se[...]

Home T o set home for the first time: 1. Press MAP . 2. Press “ Nav . Menu ” . 3. Press “ Stored Locations ” . 4. Press “ Home ” . 5. Press “ Add ” . REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Entertainment Systems 59[...]

6. Select the desired menu item you wish to set as Home (Address, Memory Point, Point of Interest, Previous Destination). 7. Enter the required details. 8. Press OK to set the home position. T o view home, press the home icon (house) on the Destination Entry screen. REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market[...]

T o view the set home position 1. Press MAP . 2. Press “ Nav . Menu ” . 3. Press “ Stored Locations ” . 4. Press “ Home ” . 5. Press “ List ” . REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Entertainment Systems 61[...]

Deleting a home location 1. Press MAP . 2. Press “ Nav . Menu ” . 3. Press “ Stored Locations ” . 4. Press “ Home ” . 5. Press “ Delete ” . REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Entertainment Systems 62[...]

6. Press YES to confirm. Special memory points There are five possible special memory points that you can set. T o set a memory point: 1. Press the MAP hard key . 2. Press “ Nav . Menu ” . REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Entertainment Systems 63[...]

3. Press “ Stored Locations ” . 4. Press “ Special Memory ” . 5. Press “ Add ” and select a position. 6. Select point 1 – 5. 7. Input a destination. 8. Press OK. Once all five special memory points are entered, the “ Add ” control will read as “ Full ” . Y ou must delete points before more can be added. T o delete a memory poi[...]

3. Press “ Stored Locations ” . 4. Press “ Special Memory ” . 5. Press “ Delete ” . The list will display . 6. Select the special memory point to delete. 7. Press “ Del. all ” to delete all entered special memory points. 8. Press “ Ye s ” to confirm. Detour options Y ou may engage the detour option once a route has already been [...]

Press DETOUR to activate. Use the soft controls to select and enter the number of miles you want to deviate off of the current road. Press DETOUR to confirm the selection and to activate the detour around the specified areas. Press NEW ROUTE if you would like the system to plan a different route. The system may calculate an entirely new route, depe[...]

Avoiding an area while under guidance For one reason or another , you may choose to avoid a certain area while in route to your destination. T o select the area to avoid: • From the MAP screen, press Nav Menu. • Select Route Options, then Display Whole Route • Press T urn List • Press A void next to the street to be avoided • Choose OK to[...]

Deleting areas to avoid T o delete a selection from the “ A void area ” list: • From the stored locations menu, select “ A void area ” . • Press DELETE • Select the desired area to be deleted. • Press DEL. ALL to delete all stored areas. • Press YES to confirm. Destination menu Press DEST on the main bezel to access the navigation[...]

Initial map display After pressing AGREE to the initial W ARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock (if equipped). Note: There may be a slight time delay between the soft key [...]

Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey . The navigation system will recalculate your route to get you back to an appropriate road to your destination. Destination entry Selecting a destination Press DEST to set a destination. From this men[...]

Search area The mapped areas covered by your map DVD are reflected in the Search Area map that is displayed on the Destination Entry screen. Y our navigation system uses a regional search area. This area is the area from which navigational directions will be used. T o check your area or reset, press CHANGE under the search area listing. The map wil[...]

Points of interest (POI) Select “ Point of Interest ” from the Destination Entry Menu. In this next menu, you will have the following options: • By Name — Enter POI name on the keyboard. T ouch “ List ” to display the list of matching points of interest. If there are too many matches being listed, try entering the town name first. • B[...]

Deleting stored locations Y our navigation system allows you to delete any stored locations (previous destinations, memory points, special memory points, home, avoid areas, destination and way points, etc.) T o delete any of these stored locations: 1. Press the MAP hard key . 2. Press “ Nav Menu ” in the bottom left hand corner of the screen. 3[...]

4. Select the desired item you wish to delete (previous destination, memory point, etc.). 5. Press “ Delete ” at the bottom of the screen. 6. The list of stored locations will be displayed. 7. Select (touch) the entry to be deleted. The item details will be listed. 8. Press YES to confirm the deletion. 9. Press DELETE ALL to delete all stored l[...]

Adding a memory point Y ou may add more memory points to be stored in the system. 1. W ith the map displayed, touch your finger to the screen to scroll to the desired location. When you reach the desired location, remove your finger from the screen and the map will stop scrolling. STORE will appear on the screen. 2. Press STORE to add the location [...]

4. Select “ Memory Point ” . 5. Press “ Add ” at the bottom of the screen. 6. Select the desired menu item. 7. Enter/select any required details. The new point will be added to the stored list of memory points. 8. Press OK. The new point will be added to the list of stored memory points. T o give the new memory point a name: 1. Select it fr[...]

3. Press “ Stored locations ” . 4. Press “ Memory Point ” . 5. Press LIST 6. Select the desired entry to view its location details. Sorting memory point lists 1. Access the desired list. 2. Press the button to sort the list as desired (i.e. date, name, or icon). When sorted by distance, the points are ordered by distance from the current ve[...]

Choosing from the icon list After selecting a location, press ICON to edit. There will be 15 normal and three sound icons displayed. Press the icon you wish to use. The normal icons will be displayed on the map to indicate the map location identified with that icon. The audible icon will sound a distinctive chime when the vehicle is approaching the[...]

Freeway Entrance/Exit T o set a freeway entrance or exit as a destination: 1. Press the DEST hard key . 2. Press “ Next page ” to access the second page of the Destination Entry menu. 3. Select “ Freeway Entrance/Exit ” . 1. Enter freeway name — Enter the freeway name using the keyboard. Press “ List ” to select a freeway from those d[...]

Destination and way points The Store Dest. & W ay Point menu is used after a destination or way point has been entered for the first time using the Destination Entry menu. Y ou can store and delete destinations and way points (locations you wish to visit in route to your ultimate destination). Y ou can also select the order in which you visit t[...]

Editing and changing order of way points and destination Press “ Chg. Order ” to change the order in which the way points are visited. The points are listed chronologically from bottom up, the destination being on the top. Press the MAP button to edit the way point location on the map display . Press OK to confirm. Deleting way points and desti[...]

Route calculation Once the route criteria is selected, the navigation system automatically calculates the selected destination. The route appears on the display screen and a voice prompt provides instructions. The system may calculate up to four routes for the desired destination. Press “ Next ” to scroll through the various planned routes. Pre[...]

Menu mode T o access menu mode, press the MENU hard control. Menu mode allows you to access: • System Set-up • Information — Gives you the Lincoln Customer Assistance Center information. • Brightness/Contrast — Allows you to adjust the brightness and contrast on the screen. REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) [...]

• Screen off — Allows you to turn off the navigation screen. System setup The system set up menu contains the following user settings: • Audible Feedback — Press to activate audible voice navigation commands. Press again to deactivate. • Navigation Units — Press to toggle between Metric/English units. • Language — Press to toggle be[...]

General information Safety information Please read and follow all stated safety precautions. Failure to do so may increase your risk of collision and personal injury . Ford Motor Company shall not be liable for any damages of any type arising from failure to follow these guidelines. Do not attempt to service, repair or modify the system. See your F[...]

Do not disassemble or modify the system as this may lead to damage and void your warranty . If a problem occurs, stop using the system immediately and contact your Ford or Lincoln Dealer . Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln Mercury could void user ’ s authority to operate the eq[...]

traffic lights and thunderstorms. Moving away from an interfering structure (out of its “ shadow ” ) returns your reception to normal. • Station overload. W eak signals are sometimes captured by stronger signals when you pass a broadcast tower . A stronger signal may temporarily overtake a weaker signal and play while the weak station frequen[...]

• Not harmful but not recommended- ammonia cleaner , neutral detergent. • Harmful to system and not recommended- acid cleaner , alkali cleaner , benzene cleaner . Do not clean any part of the system with benzene, paint thinner or any other solvent. Do not spill liquids of any kind onto the unit. Loading the map DVD • Y our navigation DVD unit[...]

DUAL ELECTRONIC AUTOMATIC T EMPERATURE CONTROL (DEA TC) SYSTEM (IF EQUIPPED) 1. A/C control: Press to turn on and manually control the air conditioning. Press again to disengage. Press AUTO for the system to automatically control the temperature. 2. Recirculation control: Press to engage/disengage. Used to manually enable or disable recirculated ai[...]

4. Rear defrost: Press to defrost the rear window . Refer to Rear window defrost in this section for more information. 5. DUAL zone selector: Press to toggle the system between single zone and dual zone control. 6. (Defrost): Distributes outside air through the windshield defroster ducts and the demister outlets. Can be used to clear ice or fog fro[...]

14. Driver ’ s side temperature control: Controls the temperature on the driver side of the vehicle in dual zone and controls the temperature of the entire vehicle in single zone. 15. Fan Speed: Press to manually increase/decrease fan speed. In manual mode, the display will show with a bar graph to indicate fan speed. Fan speed can be manually ad[...]

DUAL ELECTRONIC AUTOMATIC T EMPERATURE CONTROL (DEA TC) SYSTEM WITH HEATED AND COOLED SEATS (IF EQUIPPED) 1. A/C control: Press to turn on and manually control the air conditioning. Press again to disengage. Press AUTO for the system to automatically control the temperature. 2. Recirculation control: Press to engage/disengage. Used to manually enab[...]

(two lights). Press a third time to select low heat (one light). Press a fourth time to disengage the feature (all lights will be off). 5. R (Rear defrost): Press to defrost the rear window . Refer to Rear Window Defrost for more information. 6. Passenger cooled seat: Press to turn on the passenger side cooled seat. Press once for full cool (three [...]

11. Auto: Press to engage automatic temperature control. Use the temperature control to select the desired temperature setting. The system will automatically determine fan speed, airflow location, A/C on or off, and outside or recirculated air to heat or cool the vehicle, allowing it to reach the desired temperature. Press and hold AUTO for about t[...]

17. T emperature conversion: Press to toggle between Fahrenheit and Celsius temperature on the DEA TC display only . The set point temperatures in Celsius will be displayed in half-degree increments. Heated wiper rest: Heats the windshield wiper blades in order to reduce the chance of ice buildup and to aid in defrosting. This feature operates auto[...]

• Do not place items over the climate temperature sensor grid. This may cause improper operation of the system. T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Ensure that recirculation is disengaged. 3. Set the temperature control to full heat. 4. Set the fan to the highest speed. 5. Direct the outer instrument panel v[...]

Do not use razor blades or other sharp objects to clean the inside of the rear window or to remove decals from the inside of the rear window . This may cause damage to the heated grid lines and will not be covered by your warranty . CABIN AIR FILTER Y our vehicle is equipped with a Cabin air filter . The particulate air filtration system is designe[...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. • T o turn autolamps on, rotate the cont[...]

Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is pulled toward you and is in any of the following positions: • Parking lamps • Low beams • Autolamps (when active) Foglamps will turn off when the highbeams are activated. Daytime running lamps (DRL) (if equipped) T urns the highbeam headlamps on with a re[...]

Flash to pass Pull toward you slightly to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during parklamp, headlamp and autolamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate fully up to turn on the interior lights. Note: The panel dimmer control is not active[...]

• (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen 2.1 inches (50 mm) below this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens (use the lo[...]

INTERIOR LAMPS Map lamps The map lamps and controls are located on the dome lamp. Press the controls in front of each map lamp to activate the lamps. BULBS Replacing exterior bulbs Check the operation of all the bulbs frequently . Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an author[...]

Function T rade Number License plate lamp 168 High-mount brakelamp LED* Map lamp (with moon roof) 906 Rail lamp (rear) 168 Map lamp (front) 906 Sun visor lighted mirror lamp E9SB-13465-BA Glove compartment 194 Ashtray 194 Luggage compartment lamp 212-2 All replacement bulbs are clear in color except where noted. T o replace all instrument panel lig[...]

Replacing headlamp bulbs - lowbeam 1. Remove the headlamp assembly as described under Replacing headlamp bulbs earlier in this section. 2. Remove the four T20 torx head screws holding the bulb retaining cover on. 3. T urn the bulb counterclockwise and remove it by pulling the bulb straight out. 4. Disconnect the electrical connector . Handle a halo[...]

Install the new bulb in reverse order , while also replacing the seal on the bulb retaining cover . The kits for replacement seals are available at Lincoln or Ford dealers. Replacing the LED sidemarker 1. Remove the headlamp assembly as described under Replacing headlamp bulbs earlier in this section. 2. Remove the three T20 torx head screws holdin[...]

Replacing foglamp bulbs 1. Make sure the headlamp switch is in the OFF position and disconnect the electrical connector from the foglamp bulb. 2. Rotate the foglamp bulb counterclockwise and remove from the foglamp. Install the new bulb in reverse order . Replacing high-mount brakelamp bulbs Y our vehicle is equipped with an LED center high-mount s[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • Quickly pressing the end of the stalk switch causes a single wipe without washer fluid. • Push and hold the end of the s[...]

2. Firmly press the release tab from the bottom side of the wiper arm to unlock wiper blade from wiper arm. 3. Pull the wiper blade down toward the windshield to remove it from the arm. 4. Attach the new wiper to the wiper arm and reposition the clip until it locks. Repeat for driver ’ s side wiper arm. POWER TILT/TELESCOPE STEERING COLUMN The st[...]

Easy entry/exit feature When you remove the key , the column will move, if this feature is activated through the Message Center , to the full in and up position, refer to the Message Center in the Driver Controls chapter . When the key is inserted into the ignition, the column will return to the previous setting. Note: The easy entry/exit feature w[...]

OVERHEAD CONSOLE The appearance of your vehicle ’ s overhead console will vary according to your option package. Storage compartment Press to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object. AUXILIARY POWER POINT Power outlets are designed for accessory plugs only . Do not hang any type o[...]

POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press the rocker switches to op[...]

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Restoring the Express up functionality Under low battery power conditions, Express Up only functionality may be lost. T o reset this function after restoring full battery power , press[...]

the clear state to the non-glare state when bright lights (glare) reach the mirror . When the mirror detects bright light from behind, it will automatically adjust (darken) to minimize glare at night only . The mirror will automatically return to the clear state whenever the vehicle is placed in R (Reverse)(when the mirror is on). Do not block the [...]

The compass reading will remain fixed when significant levels of magnetic interference are experienced (such as steel bridges). The compass will return to normal operation upon leaving the magnetized area. If highly magnetized items (such as magnetic mount antennas) are placed very near the compass the display will change to “ C ” .I fa “ C ?[...]

1. Start the vehicle. 2. Press and hold the COMP side of the control until “ C ” appears in the mirror display . 3. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until the display reads a direction. 4. The compass is now calibrated. Power side view mirrors T o adjust your mirrors: 1. Select to adjust the left mirror or to adjus[...]

Fold-away mirrors (if equipped) Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control (loc[...]

SPEED CONTROL W ith speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h). Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Setting speed control The controls for using yo[...]

Resuming a set speed Press the RES control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you[...]

• Depress the brake pedal until the desired vehicle speed is reached, press the SET + control. Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal . This will not erase your vehicle ’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or[...]

In AM, FM1, or FM2 mode: • Press ⌬ or ⵜ to select preset stations within the selected radio band. In T ape mode: • Press ⌬ or ⵜ to select the next selection on the tape. In CD mode: • Press ⌬ or ⵜ to select the next selection on the CD. In any mode: • Press VOL + or − to adjust volume. Press the PHONE/MUTE control to mute the [...]

Navigation steering wheel controls (if equipped) These controls allow you to operate some audio and navigation control features when the vehicle is equipped with the navigation feature. Audio control features Press MEDIA to select: • AM, FM1, FM2, or • CD. In AM, FM1, or FM2 mode: • Press NEXT to select preset stations within the selected rad[...]

Navigation control features Press and hold VOICE until the voice icon appears to use the navigation voice guidance. Press REPEA T control to hear previous command repeated from the navigation system. MOON ROOF (IF EQUIPPED) T o open the moon roof: • Push up on the control to raise the moon roof to the vent position. • Push up on the control, wh[...]

• T o close from the vent, intermediate and full open positions, push the rear portion of the control forward. Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. When closing the moon roof, you should verify it is free of obstructions and ensure that children and/or pets ar[...]

Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink 威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink 威 buttons be erased for security purposes, refer to Programming in this section. Programming Do not program HomeLi[...]

5. Press and hold the just-trained HomeLink 威 button and observe the indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink 威 button is pressed and released. Note: T o program the remaining two HomeLink 威 buttons, begin with step 2 in the “ Programming ” section — do not repe[...]

seconds ( “ cycle ” ) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly after HomeLink 威 accepts the radio frequency signal. • Proceed with step 4 in the “ Programming ” section. Operating the HomeLink 姞 Wireless Control System T o opera[...]

For questions or comments, contact HomeLink 威 at www .homelink.com or 1 – 800 – 355 – 3515. CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others ’ safety when using such equipment. Mobile Commun[...]

RESET Press this control to select and reset functions shown in the FUEL, SETUP and ST A TUS controls. SETUP Press this control for the following displays: • Units (English/Metric) • Autolocks • Easy Exit Seat (if equipped) • Autolamp Delay • Lock Chirp (if equipped) • Language ST A TUS Selecting this function from the ST A TUS control [...]

Message center functions Dist T o Empty (DTE) Selecting this function from the FUEL control estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW F[...]

Y ou may notice gradual improvement in fuel economy over the course of your vehicle ’ s break-in period (approximately 1,000 miles [1,600 kilometers]). 1. Press the FUEL control to display miles to empty . Press again to display average fuel economy . 2. Set the speed control. Refer to Speed control in this chapter . 3. Press the RESET control to[...]

Easy exit seat (if equipped) 1. Select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the easy entry/exit ON or OFF . Autolamp delay 1. Select this function from the SETUP control for the current display mode. 2. Press the RESET control to select a new Autolamp delay value. Lock chirp (if equip[...]

System warnings System warnings alert you to possible problems or malfunctions in your vehicle ’ s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warn[...]

W arnings Status Low brake fluid level W arning returns after the ignition key is turned from OFF to RUN Check tail lamps Check brake lamps Check front turn lamps Check side repeater lamps (if equipped) Check rear turn lamps Check T raction Control Check AdvanceT rac (if equipped) T runk ajar Low washer fluid Check AC (cabin) filter Change oil soon[...]

P ASSENGER REAR DOOR AJAR. Displayed when the passenger side rear door is not completely closed. P ARK BRAKE ON & NEED SER VICE. Displayed when the park brake is ON and malfunctioning. If the warning stays on or continues to come on, contact your dealer as soon as possible. P ARK BRAKE ON. Displayed when the park brake is ON. If the warning sta[...]

LOW BRAKE FLUID. Indicates the brake fluid level is low and the brake system should be inspected immediately . Refer to Checking and adding brake fluid in the Maintenance and Specifications chapter . CHECK T AIL LAMPS. Displayed when the tail lamps are activated and at least one is burned out. Check the lamps as soon as safely possible and have the[...]

CHECK A/C (cabin) FIL TER. Displayed when the A/C cabin filter life remaining is 5 percent or less. When A/C filter life left is between 5% and 0%, the CHANGE A/C FIL TER SOON message will be displayed. When A/C filter life left reaches 0%, the A/C FIL TER CHANGE REQUIRED message will be displayed. T o reset the A/C filter monitoring system to 100%[...]

2. Press and hold the RESET control to set to 100%. 3. After a successful reset, the message center will display OIL LIFE SET TO 100%. T o reset the oil monitoring system to your personalized oil life %: 1. Press the ST A TUS control to access the System Check function. Press RESET to reset oil %. 2. Press RESET and SETUP controls at the same time [...]

DA T A ERROR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel computer • Engine sensor • Gear selection • Door sensor • T runk sensor • Exterior lamps • T raction Control 娂 and AdvanceT rac 娂 (if equipped) • Memory feature Contact your dealer as soon as possible [...]

FUEL DOOR RELEASE Press the remote fuel door release control on the instrument panel to open the fuel door . The fuel door has a manual override release located in the trunk. Pull the tab to open the fuel door . REMOVAL/INSTALLATION OF ASHTRAY In order to prevent damage, follow these instructions when removing/installing the ashtray . Removal: 1. P[...]

CENTER CONSOLE Y our vehicle may be equipped with a variety of console features. These include: 1. Cupholders 2. Sliding arm rest (lift latch to slide forward or rearward) Note: Slide the arm rest to the rearward position to open the utility compartment 3. Utility compartment, inside has power point (front drivers side) and coin holders (front pass[...]

CARGO NET (IF EQUIPPED) The cargo net secures lightweight objects in the cargo area. This net is not designed to restrain objects during a collision. There are four straps on the net and six anchors in the trunk that can be used for securing different sized objects. T o attach the cargo net to the anchors: • T ake the bottom strap of one side of [...]

KEYS Y our vehicle is equipped with two master keys and a valet key lock system. The master key will access the driver ’ s door , trunk, glove box, remote trunk release control and ignition. The valet key will access door and ignition only . Refer to the Securilock 娂 Passive Anti-Theft System section for information on Securilock 娂 keys. POWE[...]

seconds to begin to open all the windows and moonroof. Releasing the control on the remote entry transmitter , or returning the key to the center position will stop all motion. Note: The ignition must be in the 2 (OFF) position and the accessory delay feature must not be activated in order for this feature to operate. Closing all windows and moonro[...]

Childproof door locks • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on the rear edge of each rear door and must be set separately for each door . Note: Setting the lock for one door will not automatically [...]

Keep vehicle doors and luggage compartment locked and keep keys and remote transmitters out of a child ’ s reach. Unsupervised children could lock themselves in the trunk and risk injury . Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly . Exposure of people or [...]

The remote entry system allows you to perform the following tasks using the remote entry transmitter: • unlock the vehicle doors. • lock all the vehicle doors. • open the trunk. • activate the personal alarm. • open all windows and moonroof (if equipped). • arm and disarm the perimeter anti-theft system. • operate the illuminated entr[...]

2. Press and release again within five seconds to unlock all the doors. The remote entry system comes with an illuminated entry feature. This feature turns on the puddle lamps and the interior lamps for 20 seconds or until the ignition is turned to the 5 (ST ART) position. The inside lights will not turn off if: • they have been turned on using t[...]

Sounding a panic alarm Press on the remote transmitter to activate the alarm. Press a second time to deactivate the alarm. Y ou may also deactivate the alarm in the following ways: • Press on the remote transmitter . • T urn the ignition to the 4 (RUN) position. • W ait 30 seconds for the alarm to time-out. Opening the trunk Press once to ope[...]

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery . Press the batt[...]

T o reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. T urn the key from the 1 (LOCK) position to 4 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 4 (RUN). Note: The eighth turn must end in the 4 (RUN) position. 5. The doors will l[...]

Autolock The autolock feature will lock the vehicle ’ s doors when: • all the doors are closed, • the ignition is in the 4 (RUN) position, • you shift into forward or reverse, and • the vehicle speed is greater than 3 mph (5 km/h). Relock The autolock feature repeats when: • either door is opened then closed while the ignition is in the[...]

2. Press the SET control on the driver ’ s door panel. 3. W ithin 5 five seconds, press any control on the remote transmitter and then press the 1 or 2 control on the driver ’ s door panel to associate with the Driver 1 or Driver 2 positions. 4. Repeat this procedure for another remote transmitter if desired. Deactivating the memory feature T o[...]

Programming a personal entry code T o create your own personal entry code: 1. Enter the factory set code. 2. W ithin five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other . 4. Enter a sixth digit to indicate which personality feature should be recalled by the[...]

The anti-scan feature will turn off after: • one minute of keypad inactivity . • pressing the UNLOCK control on the remote entry transmitter . • the ignition is turned to the 4 (RUN) position. Unlocking and locking the doors using keyless entry T o unlock the driver ’ s door , enter the factory set 5-digit code or your personal code. Each n[...]

Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. Y ou need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key , but may cause a momentar[...]

Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in the 4 (RUN) position for at least three seconds, but no more than ten seconds). 2. T urn the ignition to the 1 (LOCK) position and remove the first coded key from the [...]

The system is ready to arm whenever key is removed from the ignition. Any of the following actions will prearm the alarm system: • Press the control on the remote entry transmitter . • Press the driver or passenger interior power door lock control while that respective door is open, then close the door . • Lock the vehicle with the key in the[...]

SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat ’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Adjustable head restraints Head restraints help to limit head motion in the [...]

Using the manual lumbar support (if equipped) The lumbar control is located on the front of the seat cushion. T urn to adjust lumbar support. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the front of the control to increase firmness. Press the back of the control to decreas[...]

Rotate the vertical control to adjust the seatback. • Driver • Passenger Slide the control forward or backward to move the seat forward or backward. • Driver • Passenger Move the control up or down to move the seat up and down. • Driver • Passenger Move front/rear of control up or down to tilt the front/rear of the seat cushion. • Dri[...]

Deactivating/activating the easy entry/easy exit feature The easy entry/easy exit feature can be turned off or on through the vehicle message center (if equipped). If your vehicle does not have a message center , the feature can be turned off or on by your dealer . Memory seats/steering column/mirrors/adjustable pedals (if equipped) This system all[...]

Climate controlled seats air filter replacement The climate controlled seat system includes air filters that must be replaced periodically . Refer to the Scheduled Maintenance Guide for more information. • There is a filter located under each front seat. • They can be accessed from the second row seat. Move the front seats all the way forward a[...]

• Remove filter . T o install a filter: • First, position the filter in it ’ s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position. REAR SEATS Adjustable rear head restraints (if equipped) Head re[...]

Push control to lower head restraint. Rear heated seats (if equipped) • Push the indicated side of the button for low heat. • Push again to deactivate. • Push the indicated side of the button for high heat. • Push again to deactivate. The heated seats will activate when the ignition is in the RUN position. When activated, they will turn off[...]

T o lower the seatback(s), pull the release handle(s) located inside the trunk. Fold the seatback(s) down. When raising the seatback(s), make sure they are fully latched and that you hear the seat latch into place. Failure to do so could result in serious personal injury in the event of a collision. Make sure that the safety belts for the rear cent[...]

• Driver and passenger side air curtains (if equipped) • Front safety belts with pretensioners, energy management retractors, and safety belt usage sensors • Driver ’ s seat position sensor • Front crash severity sensor • Restraints Control Module (RCM) with impact and safing sensors • Restraint system warning light and back-up tone ?[...]

of crash severity and modify the deployment strategy of the dual-stage air bags and safety belt pretensioners. Driver ’s seat position sensor The driver ’ s seat position sensor allows your Personal safety system to tailor the deployment level of the driver dual-stage air bag based on seat position. The system is designed to help protect smalle[...]

Determining if the Personal safety system is operational The Personal safety system uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the W arning light section in the Instrument cluster chapter . Routine maintenance of the Personal safety system is not required. The Restraints contro[...]

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety [...]

2. T o unfasten, push the release button and remove the tongue from the buckle. Energy management feature • This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • This seat belt system has a retractor assembly [...]

Automatic locking mode How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.[...]

How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and return to the vehicle sensitive (emergency) locking mode. After any vehicle collision, the combination lap and shoulder belt system at all passenger seating positions must be check[...]

Front safety belt height adjustment Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, push the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place. Position the safety belt height a[...]

BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver ’ s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster . If... Then... The driver ’ s safety be[...]

Reasons given... Consider ... “ Belts are uncomfortable ” W e design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. “ I was in a hurry ” Prime time for an accident. BeltMinder reminds us[...]

Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. T o disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below . One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON [...]

4. W ithin 10 seconds of the light turning on, buckle then unbuckle the safety belt. • This will disable the BeltMinder feature if it is currently enabled. As confirmation, the restraint system warning light will flash 4 times per second for 3 seconds. • This will enable the BeltMinder feature if it is currently disabled. As confirmation, the r[...]

Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Interior in the Cleaning chapter . AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the [...]

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm) between an occupant ’ s chest and the driver air bag module. Never place your arm over the air bag module as[...]

Children and air bags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Air bags can kill or injure a child in a child seat. NE[...]

The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small [...]

• and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system wiring (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power , the air bag ignitors and safety belt pretensioners. Determining [...]

Do not lean your head on the door . The side air bag could injure you as it deploys from the side of the seatback. Do not attempt to service, repair , or modify the air bag SRS, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer . All occupants of the vehicle should always wear their safety belts ev[...]

not of the type sufficient to cause activation. Side air bags are designed to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air[...]

Side air curtain system (if equipped) Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision. Do not place o[...]

All occupants of the vehicle, including the driver , should always wear their safety belts even when an inflatable curtain is provided. T o reduce the risk of injury , do not obstruct or place objects in the deployment of the inflatable curtain. How does the side air curtain system work? The design and development of the side air curtain system inc[...]

Side air curtains and side air bags, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side air curtains are mounted to the sheet metal above the first and second row seats. In certain lateral collisions, the air curtain and seat-mounted side air bag on the side affe[...]

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrument cluster chapter . Routine maintenance of the air bag is not required. Any difficulty with the system is indicated by one or more of the followin[...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat. C[...]

Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child st[...]

Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs (18 kg). The shoulder belt should cross the chest, resting snugly on the center of the shoulder . The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat,[...]

When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fast[...]

Installing child safety seats with combination lap and shoulder belts Air bags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. Children 12 and under should be properly restrained in the rear[...]

3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer ’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until [...]

7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in pla[...]

The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . 1. Position the child safety seat on the seat cushion. 2. Route the child safety se[...]

5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 7. T ighten the child safety seat tether strap acco[...]

Never attach two LA TCH child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. The lower anchors for child seat installation are recessed at the rear section of the rear seat between the cushion and seat back. The LA TCH anchor[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are [...]

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. T emperature A B C The temperature grades are A (the highest), B and C, representing the tire ’ s resistance to the generation of heat and its ability to dissipate[...]

• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire ’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard[...]

Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove stones, nails, glass or other objects that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cuts, bruises and other damage. If interna[...]

higher than the manufacturer ’ s recommended cold inflation pressure which can be found on either the tire label or certification label which is located on the B-Pillar or the edge of the driver ’ s door . The cold inflation pressure should never be set lower than the recommended pressure on the tire label or certification label. When weather t[...]

TIRE REPLACEMENT REQUIREMENTS Y our vehicle is equipped with tires designed to provide a safe ride and handling capability . Only use replacement tires and wheels that are the same size and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford. Use of any tire or wheel not recommended by Fo[...]

When driving with the T -type/mini-spare tire do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • T ow a trailer • Use snow chains on the end of the vehicle with the T -type/mini spare tire • Use more than one T -type/mini spare tire at a time • Use commercial c[...]

• Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capabil[...]

3. Lift the trunk cargo cover and remove the spare tire, jack and lug wrench. 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Tires, Wheels and Loading 207[...]

5. Put the jack in the jack notch next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. Never use the rear differential as a jacking point. T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your ve[...]

9. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 10. Put flat tire, jack and lug wrench away . Make sure jack is fastened so it does not rattle when you drive. 11. Unblock the wheels. WHEEL LUG NUT TORQUE SPECIFICATIO[...]

Information on “ P ” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), th[...]

Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]

12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire grad[...]

Additional information contained on the tire sidewall for “ LT ” type tires “ LT ” type tires have some additional information beyond those of “ P ” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Ran[...]

Information on “ T ” type tires “ T ” type tires have some additional information beyond those of “ P ” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and[...]

the road in adverse (wet, snowy , etc.) conditions. Visually check your tires for uneven wear , looking for high and low areas or unusually smooth areas. Also check for signs of tire damage. When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to prevent your vehicle from skidding and hydroplaning. Built-in treadwear indi[...]

• A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Never spin the tires in excess of [...]

your tires wear more evenly , providing better tire performance and longer tire life. Unless otherwise specified, rotate the tires approximately every 5,000 miles (8,000 km). • Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires a[...]

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln/Mercury dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equipped with a dissimilar spare[...]

V EHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, [...]

Note: For trailer towing information refer to T railer towing found in this chapter or the RV and T railer T owing Guide provided by your dealership. GVW (Gross V ehicle W eight) – is the V ehicle Curb W eight + cargo + passengers. GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all [...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

Steps for determining the correct load limit: 1. Locate the statement “ The combined weight of occupants and cargo should never exceed XXX pounds ” on your vehicle ’ s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XX[...]

The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle W eight Rating specified for your vehicle on the Certification label found on the driver ’ s door . Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum GCWR chart (in the T[...]

STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. (The steering wheel will not lock after key removal.) 2. OFF , shuts off the engine and all accessories without locking the steering wheel. This position also allows the automatic transmission shift lever to be moved from the P (Park) position without the [...]

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding a[...]

• T urn the key to 4 (ON) without turning the key to 5 (ST ART). Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver ’ s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever you start your vehicle, release the key [...]

3. After idling for a few seconds, apply the brake, shift into gear and drive. Using the engine block heater (if equipped) An engine block heater warms the engine coolant which aids in starting and heater/defroster performance. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -10 ° F (-23 ° C)[...]

Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking and the brake pedal may suddenly travel a litt[...]

Parking brake T o set the parking brake, pull the lever up. T o release the parking brake, make sure the ignition is turned to ON, depress the brake pedal, then gently push the parking brake lever down. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. The parking brake will automatically diseng[...]

STEERING T o prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). If the power steering system breaks down [...]

The T raction Control 娂 switch, located on the center console by the gearshift lever , has an indicator light that illuminates when the system is off. The T raction Control 娂 system will automatically turn on every time the ignition is turned off and on. If you should become stuck in snow or ice or on a very slippery road surface, try switching[...]

AdvanceT rac 娂 enhances your vehicle ’ s stability during maneuvers that require all available tire traction, like in wet/snowy/icy road conditions and/or when performing emergency maneuvers. In an emergency lane-change, the driver will experience better overall vehicle traction, and have better control of the vehicle. The AdvanceT rac 娂 syst[...]

indicator light in the instrument cluster remains on while the engine is running, have the system serviced immediately . Pressing the control once will disable the AdvanceT rac 娂 stability enhancement and the engine power reduction portion of the traction enhancement feature; the brake portion of the traction enhancement feature will still functi[...]

AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the RUN position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the RUN position and t[...]

Driving with a 5 – speed automatic transmission This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle ’ s battery has been disconnected for any type of service or repair , the transmission will need to relearn the normal shi[...]

R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. Drive 5 (Overdrive) The normal drivi[...]

• Selecting 2 (Second) at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed. 1 (First) This position allows for first gear only . • Provides maximum engine braking. • W ill not downshift into first gear at high speeds; will cause the transmission to downshift to a lower gear , then allows f[...]

Manual shift mode W ith the gearshift lever in D5 (Overdrive), the gearshift lever can be moved to the right and into the manual shift mode. The transmission will remain in the manual shift mode until the gearshift lever is moved back to D5 (Overdrive). + and - position operation These positions allow the driver to manually select the appropriate u[...]

• If shifter (-) is tapped more than once in rapid succession, the transmission will downshift only into the next lower gear , then when the vehicle reaches a speed below a calibrated entry speed, the transmission will allow a downshift into the next lower gear if again selected by the driver . This is to prevent engine and transmission damage an[...]

T o help avoid personal injury , always use caution when in R (Reverse) and when using the rear park assist. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting objects to avoid damaging the vehicle. The system may not detect smaller objects, part[...]

The rear park assist is automatically enabled when the gear selector is placed in R (Reverse) and the ignition is ON. A park assist control allows the driver to disable the system only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled. Press the control to disable or [...]

GETTING ROADSIDE ASSISTANCE T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24 – hours, seven days a week • for the New V ehicle Limited W arranty period of three years o[...]

Canadian customers who require roadside assistance, call 1 – 800 – 665 – 2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. T o obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1 – 800 – 521 – 4[...]

This switch is located in the driver ’ s footwell, behind the kick panel. T o reset the switch: 1. T urn the ignition OFF . 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. T urn the ignition ON. 5. W ait a few seconds and return the key to OFF . 6. Make another check for leak[...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey ——— 3A Violet V iolet ——— 4A Pink Pink ——— 5A T an T an ——— 7.5A Brown Brown ——— 10A Red Red ——— 15A Blue Blue ——— 20A Y ellow Y ellow Y ellow Blue Blue 25A Na[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Starter relay coil 2 5A Radio 3 5A ABS/TCS/AdvanceT rac 娂 4 5A Cluster , Powertrain Control Module (PCM) relay , Fuel pump relay , REM 5 10A Restraints Control Module (RCM) 6 10A OBD II 7 5A DDM, DSM, Anti-theft LED, Power mirror [...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 10 5A Left front turn, Left front sidemarker , Left front park lamps 11 10A Left front high beam 12 5A Electrochromic mirror 13 5A Cluster 14 5A DA TC 15 5A O/D cancel, ABS/T raction-Assist switch 16 5A Heated seat controls, Climate control seat module 17 5A RCM, Alter[...]

Front power distribution box The front power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle ’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. T o reduce risk of electrical shock, always replace the [...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 10A* A/C clutch, Coolant control valve, Auxiliary coolant pump 2 — Not used 3 15A* Fog lamp 4 20A* Horn 5 15A* Fuel injectors, Electric cooling fan, Mass Air Flow (MAF) sensor 6 15A* T ransmission solenoid, EGR 7 — Not used 8 ?[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 13 30A** Heated wiper park 14 30A** ABS module 15 — Not used 16 30A** Blower motor 17 — Not used 18 — Not used 19 30A** Electric park brake 20 30A** W iper motor 21 30A** Starter solenoid 22 40A** ABS motor 23 — Not used 24 — Not used Relay 01 — Not used Relay 02 —[...]

In-line fuse for electric cooling fan There is a 60A maxi fuse for the electric cooling fan located in a wiring harness behind the front passenger side trim panel under the dash panel. The trim panel must be removed and the carpet on the front passenger side must be lifted to access this fuse. See a qualified technician to have this fuse replaced, [...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 15A* Decklid release solenoid, Passenger door lock motors 2 10A* Right rear turn lamp, License plate lamp 3 5A* Left rear stop/tail lamp 4 10A* Fuel door release solenoid, Decklid lamp 5 10A* Courtesy and map lamps, Radio antenna mo[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 17 15A* Fuel pump motor 18 20A* Subwoofer amp 30A* THX amp, Subwoofer amp 19 20A** REM - Left rear window 20 30A** Front window motors 21 20A** Driver lumbar , Power seats 22 20A** Ignition switch 23 30A** SSP4 24 30A** SSP3 25 40A** P-J/B 26 30A** Climate control seat module 27[...]

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start ca[...]

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . + – + – + ?[...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to the spare tire tie-down stud. (Y our vehicle may be equipped with a plastic cap on top of the tire tie-down stud. This cap must be removed prior to attaching the cable to the stud.) + – + – + – + [...]

Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery . 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehic[...]

2. Remove the jumper cable on the negative (-) connection of the booster vehicle ’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle ’ s battery . + – + – + – + – REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Roadside Emergencies 258[...]

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle ’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. + – + – REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own200[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a sl[...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Lincoln or Mercury vehicle to an authorized Lincoln Mercury dealer for warranty repairs. While any Ford, Lincoln or Mercury dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction. Ple[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact [...]

In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state cre[...]

• available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law .[...]

• A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs T o have your case reviewed [...]

before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well. Making a decision Board members review all available information related to each complaint, including oral presentations, and arrive at a fair and impartial decision.[...]

The CAMV AP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMV AP program, impartial third-party arbitrators conduct h[...]

GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than[...]

ORDERING ADDITIONAL OWNER ’ S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail W ash (ZC-3 – A), which is available from your dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash [...]

• Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: ?[...]

• 3.0L DOHC V6 engine • 3.9L-4V V8 engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer . • For routine cleaning, use Motorcraft Detail W ash (ZC[...]

• If tar or grease spots are present, use Motorcraft Bug and T ar Remover (ZC-42). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle ’ s glass or the wiper blades may be the cause. These may include hot wax treatments u[...]

• Do not use household or glass cleaners as these may damage the finish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags: • Remove dust and loose dirt with a vacuum cleaner . • Remove light stains and soil with Motorcraft Extra Strength Upholstery Cleaner (ZC-41). • If grease or tar is present o[...]

UNDERBODY Flush the complete underside of your vehicle frequently . Keep body and door drain holes free from packed dirt. FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Y our Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fu[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check you[...]

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located at the bottom left of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood by pushing upward on the handle. 3. Lift the hood until the lift cylinders hold it open. IDENTIFYING COMPONENTS [...]

3.9L – 4V V8 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. W indshield washer fluid reservoir 8. Power distribution box REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Mai[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16 – A2. Refer to Lubricant specifications in this chapter . State or local regulations on volatile organic compounds may restrict the use of metha[...]

5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MA[...]

3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise tightly until clicks are heard, or until it is snug. T o avoid possible oil loss, DO N[...]

It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which is located in the luggage compartment, next to the spare tire. Y our battery is designed to purge any battery gases to the outs[...]

When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]

If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about [...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “ FULL COLD ” level or within the “ COLD FILL RANGE ” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance Guide for service interval schedules. • Be sure to re[...]

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see throug[...]

remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the ca[...]

Used engine coolant should be disposed of in an appropriate manner . Follow your community ’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle ’ s cooling system can hold, refer to Refill capacities in this section. Fill your engine coolant reservoir as[...]

What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “ fail-safe ” distance depends on ambient temperatures, vehicle load and terrain. How fail-safe cooling works If the engine begins to overheat: • T[...]

4. Check the coolant level and replenish if low . Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to a service facility . Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to a service facility as soon as possible[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury . [...]

Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would h[...]

Choosing the right fuel Use only Premium UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. Studies indicate that these additives can cause your vehicle ’ s emission control system to de[...]

Many of the world ’ s automakers approved the W orld-wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the W orld-wide Fuel Charter should be used when available. Ask your fuel supplier about gasolines that meet the W orld-wide Fue[...]

Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter . The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel [...]

5. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate esti[...]

Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy . • Use recommended engine oil. Refer to Lubricant specifications in this chapter . • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and own[...]

applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • A void running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your Schedul[...]

On board diagnostics (OBD-II) Y our vehicle is equipped with a computer that monitors the engine ’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD-II). This OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD-II system also a[...]

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. POWER STEERING FLUID Refer to the scheduled maintenance guide for[...]

T RANSMISSION FLUID Checking automatic transmission fluid The 5R55S transmission does not have a transmission fluid dipstick. Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes. Y our transmission does not consume fluid. However , the fluid level should be checked if the transmission is not working proper[...]

Changing the air filter element 1. Loosen the hose clamp on the outlet tube at the air filter housing. 2. Release the two clamps that secure the cover to the air filter housing and place the cover aside. 3. Remove the air filter element from the air filter housing. 4. W ipe the air filter housing and cover clean to remove any dirt or debris and to [...]

5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . This could cause filter damage and allow unmetered air to enter the engine if not properly seated. 6. Replace the air filter housing cover and secure the clamps. Be sure all of the tabs on front edge are correctly aligned[...]

For PCV valve replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part. The customer warrant[...]

Fluid Ford Part Name Application Capacity Rear axle 3 Motorcraft SAE 75W -90 Fuel Efficient High Performance Synthetic Rear Axle Lubricant All 1.2-1.3L (2.5-2.7 pints) Fuel tank N/A All 70.0L (18.5 gallons) T ransmission fluid 4 Motorcraft MERCON 威 V AT F Automatic (5R55S) 11.2L (11.9 quarts) 5 W indshield washer fluid Motorcraft Premium W indshi[...]

LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Brake fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid 1 PM-1 ESA-M6C25-A and DOT 3 Door weatherstrips Silicone Lubricant XL-6 ESR-M13P4-A Door latch, hood latch, auxiliary hood latch, door hinges, striker plates, seat tracks and fuel filler door hing[...]

Item Ford part name Ford part number Ford specification Rear Axle Lubricant Motorcraft SAE 75W -90 Fuel Efficient High Performance Synthetic Rear Axle Lubricant 2 XY -75W90-QFEHP Automatic transmission fluid Motorcraft MERCON 威 VA T F 3 XT -5-QM MERCON 威 V W indshield washer fluid Premium W indshield W asher Concentrate ZC-32-A WSB-M8B16 – A2[...]

V EHICLE DIMENSIONS V ehicle dimensions Inches (mm) (1) Overall length 194.3 (4936) (2) Overall width 80.1 (2034) (3) Overall height 56.1 (1424) (4) Wheelbase 114.5 (2909) (5) T read - Front 60.6 (1540) (5) T read - Rear 60.7 (1543) 2 5 3 REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Maintena[...]

IDENTIFYING YOUR VEHICLE V ehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number .) 1. W orld manufacturer identifier 2. Brake type and gross vehicle weight ratin[...]

7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped). REVIEW COPY 2005 Lincoln LS (dew) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Maintenance and Spec[...]

LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for your vehicle through your local authorized Lincoln or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance[...]

Scuff plates Speed control Lifestyle Bike racks Cargo organization and management Peace of mind Airbag anti-theft locks First aid and safety kits Full vehicle covers Engine block heaters Mobile-ease hands free communication system Remote start V ehicle security systems For maximum vehicle performance, keep the following information in mind when add[...]

A Accessory delay ........................ 112 AdvanceT rac .............................. 231 Air bag supplemental restraint system ........................178, 182, 185 and child safety seats ............ 180 description .............. 178, 182, 185 disposal .................................... 188 driver air bag ..........180, 183, 186 indicator[...]

wheels ...................................... 271 wiper blades ............................ 273 Climate control (see Air conditioning or Heating) ......89, 92 Clock adjust 6-CD in dash .............................19 AM/FM/T ape/CD ....................... 23 Compass, electronic ..................113 calibration ............................... 114 s[...]

refill capacities ........................ 304 specifications .................. 306 – 307 Exhaust fumes .......................... 227 F Fail safe cooling ........................ 289 Floor mats .................................140 Fluid capacities ......................... 304 Foglamps ..................................... 99 Fuel .............[...]

J Jack ............................................ 204 positioning ............................... 204 storage ..................................... 204 Jump-starting your vehicle ......254 K Keyless entry system ............... 152 autolock ................................... 151 Keys ........................................... 142 positions of t[...]

Power distribution box (see Fuses) ....................... 248, 251 Power door locks ...................... 142 Power mirrors ........................... 115 Power point ............................... 110 Power steering .......................... 230 fluid, checking and adding .... 300 fluid, refill capacity ................ 304 fluid, specificati[...]

safety practices ....................... 215 sidewall information ............... 209 snow tires and chains ............ 218 spare tire ......................... 204 – 205 terminology ............................. 200 tire grades ............................... 200 treadwear ........................ 199, 214 T owing ..............................[...]

319[...]

320[...]