Lowrance electronic 6 manuel d'utilisation

Pub. 988-0147-383 www.lei-extras.com MapCreate 6 Custom Mapping Software for GPS Installation and Operation Instructions [...]

Copyright © 2004 LEI. All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted, distributed, downloaded or stored in any storage medium, for any purpose, without prior written consent of LEI. Any unauthorized commercial distribution of this manual is strictly prohibited. MapCreate  is a trademark of LEI. U[...]

i Table of Contents Sec. 1: Introduction ................................................................... I Quick Start Reference ................................................................... 2 How MapCreate Works: The Basics ............................................ 6 File Formats & Functions .......................................[...]

ii Trail List Window ................................................................... 43 Moving around the Master Map................................................. 44 Pan Arrows .............................................................................. 44 Center Map .........................................................................[...]

iii Notes[...]

iv WARNING! A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION. CAUTION When showing navigation data to a position (waypoint), a GPS unit will show the shortest, most direct path to the waypoint. It provides navigation data to the waypoint regardless of obstructions. Therefore, the prudent navigator will not only tak[...]

1 Section 1: Introduction How this manual can get you into the field, fast! Thanks for buying MapCreate  , the custom mapping software for Lowrance and Eagle GPS units. This manual was written using Map- Create  U.S.A. and MapCreate  Canada versions 6.3. Beginning with version 6.3, all MapCreate packages work identically, but contain dif- [...]

2 included more tips and tricks so you can take advantage of all the power and performance MapCreate offers. You can see an example of the Help file's Command Reference format in Appendix 1 at the back of this manual, on page 69. Appendix 1 contains the entry on the Help Command, which explains how to use Help. In addition to the Command Refer[...]

3 clude in your map. Use the P AN A RROW buttons to move north, south, east or west. Use the Z OOM -I N and Z OOM -O UT ( Z-I N or Z-O UT ) buttons as needed to close in on or back away from the area you're viewing. 3. Click the D RAW M AP B ORDERS button in the toolbar. Move the mouse pointer above and to the left of the desired area. Click, [...]

4 7. Another message box asks whether you want to register your current card or not. Click Y ES to continue the card registration process. Click Yes to register your current memory card with MapCreate. 8. You can change the label on your memory card if you prefer. Delete the default name, " Card1 ," and enter the new name . Click R EGISTE[...]

5 Click Done to complete the registry process. NOTE: If the A UTOMATICALLY A PPEND L ABEL T O S AVED M APS box is selected (see figure above), MapCreate will automatically add your card's label to the end of whatever name you give the file you are saving. Let's use the figure above as an example. If we name our map " Phoenix.lcm ,&qu[...]

6 How MapCreate Works: the Basics You'll be making maps faster if you understand the hoops MapCreate must jump through to cram a high-detail map into your GPS unit. First of all, those CDs you just purchased contain a whole bunch of raw digital cartography data. There are several hundred files of digital map- ping information containing lake s[...]

7 File Formats & Functions Well, now you know what makes MapCreate tick. You may be ready to skip forward to where we explain how our text formatting makes the manual easy to skim. If that's the case, move on to "How to Use This Manual: Typographical Conventions" on page 15. But, if you want to pick up an extra tip or two, look o[...]

8 hard drive space is available, many users like to archive Map Files in the C:Program FilesLEIMapCreateData folder. This allows you to change maps on your card and reuse a map over and over without creating it each time. If you save a map to the Data folder, MapCreate will remember that location the next time you save a map, during the current[...]

9 To help you decide what size cards to buy, make some map borders cov- ering the type of travel you expect. Then use the Estimate Custom Map Size command to calculate the size. For example, one Missouri customer frequently travels and fishes in the four-state area of Kansas, Missouri, Arkansas and Oklahoma. He purchased an additional 128MB MMC, wh[...]

10 cause it allows you to match your map's file size and detail level to your card's memory capacity and your travel needs. NOTE: Due to software requirements in the GPS units, MMC or SD cards can hold a maximum of 32 different files at one time for the Lowrance iFINDER  and 1,000 different files for all other Lowrance or Eagle GPS rec[...]

11 don't fit your MMC or SD card, refer to the Help file's Command Refer- ence section for more detailed instructions on controlling file size. GPS Data File This file format contains all the GPS navigation information (waypoints, event marker icons, routes and trails) used by your GPS unit and MapCre- ate. The file extension is *.usr (fo[...]

12 36.060798, -95.783549, Church 1 36.060784, -95.761647, Turn North 2 36.161831, -95.761529, Turn N-East On Hwy66 (3) 36.162581, -95.753760, Wpt 004* 36.169981, -95.751795, Wpt 005* 36.382616, -95.556565, Turn N-West 6 36.385315, -95.560847, Turn North 7 36.503465, -95.561081, Stop Turn East 8 Text files are saved in the C:Program FilesLEIMapCr[...]

13 WARNING: You should never format an MMC containing a Navion- ics  chart or Jeppesen  aviation database. Formatting the MMC will permanently erase the chart or aeronauti- cal data from the card. GPS Unit Compatibility MapCreate 6.3 is compatible with all Lowrance and Eagle mapping GPS units that use removable MMC/SD cards for map storage. S[...]

14 Find Points of Interest On the computer master map, moving your pointer over a Point of In- terest (POI) symbol triggers a pop-up box with the POI's name. With MapCreate 6.3, when the information is available, the pop-up box also displays the POI's address and telephone number. This detailed pop-up only works for items classified as Po[...]

15 All of this information is built into MapCreate's atlas database. As long as an information category is turned on and included in your Map File, the data will be available to your GPS unit. With these and other elements, MapCreate gives you a phenomenal amount of mapping detail and information. For a more detailed list of the map categories[...]

16 Keyboard The keys on your keyboard may not be labeled exactly as they are in this manual. All key names are shown in bold, sans serif type. For ex- ample, the "Control" key is shown as Ctrl and the "Enter" key is shown as Enter . Keys are sometimes used in combinations. For example, Ctrl+T means to hold down the Ctrl key whil[...]

17 Section 2: Installing MapCreate 6.3 System Requirements MapCreate 6 requires the following minimum system resources: • IBM  compatible PC. • Pentium  133 MHz or faster processor. • 32 MB RAM • approximately 300 MB free hard disk space, depending on your version of the program. • 256 color display. • Microsoft  Windows  98[...]

18 dium-detail map data. Takes approximately 300 MB of free hard drive space. Custom - Allows installation of the program and all map data files on the hard drive. Caution: Be patient if you choose custom install. It may take several minutes for all the files to install to the hard drive. You will be prompted to insert the appropriate disc(s) throu[...]

19 Click the S TART button on the Windows taskbar, and then click R UN . 3. Type D:setup.exe (where D: is the drive letter for your CD-ROM) Type the setup command directory path and file name. 4. Click OK to begin installation. NOTE: If you are using Windows 2000 or Windows XP Professional, you may receive an error message if you are not logged on[...]

20 A. InstallShield  will load. A message box will appear, reminding you to disable any anti virus software. Click OK to continue. B. Read the complete License Agreement. If you accept the agreement, click the Y ES button; if you do not accept, click the N O button, and MapCreate will not be installed on your computer.[...]

21 C. Choose a destination folder for the program. You can accept the default (recommended) or you can choose another location. Click N EXT to continue the installation. D. Select the type of setup, and click the N EXT button to continue the installation. (See page 17 for a description of the options.)[...]

22 E. If you chose Custom install, select the components to install. Then click N EXT to continue. F. With all your preferences determined, InstallShield will begin copying files. A progress window is shown.[...]

23 G. If needed, the install will prompt you for additional discs. When asked, insert the appropriate CD and click OK to continue the setup. H. The Setup Status window shows the progress of the installation. I. When the program files have been copied, InstallShield Wizard will display a message that setup is complete. Click F INISH to close the wiz[...]

24 J. After the MapCreate files have been installed on your computer, you are prompted to install the MMC card reader drivers. Make sure the card reader is not plugged in yet, then click O K to continue. (If you stop the program, you can install the card reader later, but MapCreate will not run until the card reader is installed . To install later [...]

25 M. Read the complete License Agreement. If you accept the agreement, click Y ES . (If you do not accept, click N O , and the SD/MMC Reader software will not be installed on your computer, and MapCreate will not run.) N. Choose a destination folder for the SD-MMC Reader program. This is where you want the files to be located on your hard drive. Y[...]

26 O. Select the folder where you want to place the shortcut for the SD/MMC Reader program. You can accept the default or choose an- other location. Click N EXT to continue the installation. P. The setup program is ready to install the SD-MMC Reader program on your computer. Click N EXT to continue.[...]

27 The setup program displays the progress of the installation. Installation complete. 6. When the card reader install program is finished, the InstallShield wizard completion window appears. We strongly recommend that you[...]

28 restart your computer now. MapCreate and the card reader will not run until your computer restarts. With the "restart my computer now" option selected, click F INISH . After the computer restarts and Windows has finished loading, plug the card reader into a USB port. After Windows finishes installing the card reader, it will appear as [...]

29 C:Program FilesLEIMapCreate. Next, double-click MapCreate.exe to launch the program. Double-click MapCreate.exe to start MapCreate 6.3 from Windows Explorer. For more details on the many other ways to create and manipulate short- cuts, open your Windows help file and search for the word "shortcut."[...]

30 Notes[...]

31 Section 3: User's Guide Working With MapCreate Starting MapCreate If you installed the Compact version of MapCreate, make sure the CD- ROM for the area you intend to use is in the CD-ROM drive. Otherwise, you can insert any MapCreate CD. (Remember, even if you installed the Full version, a disc m ust be in the drive each t ime yo u star t t[...]

32 The MapCreate Screen When you start MapCreate, the opening splash screen appears while the program is loading. It will take a moment or two for the program to load the map detail. MapCreate 6 splash screen appears while program is loading. Once it's finished loading, you'll see a screen that looks like this, with a map of the world and[...]

33 MapCreate 6 GPS text list windows. You can drag the borders of these windows to resize them to suit your viewing preferences. The windows can also be manually arranged around the screen, or you can just use the default Auto Arrange setting, under the Window menu. When you close the program, MapCreate re- members the windows and map you were usin[...]

34 Master Map Window The largest window is the Master Map window. It displays the basic world background map you'll use to prepare Map Border Files and Map Files for your GPS. You can close the other list windows if you're not using them. (You can always open them later when you need them. Click V IEW and then click the window name.) This[...]

35 • When your mouse pointer moves over a map feature or landmark symbol, a Pop-up Tool Tip Box appears listing a name or descrip- tion of what the symbol represents. Pop-up Tool Tip box. When the cross-hair pointer hovers over the visi- ble wreck symbol, a red border surrounds the symbol and the tip box appears. This wrecked vessel is the "[...]

36 same time.] To display additional toolbars or remove one from your screen: 1. Click V IEW | T OOLBARS . A toolbar is active when a check mark is dis- played in the box to the left of the toolbar's name. If the toolbar is not active, the box is empty. 2. To view a toolbar click the box beside the name of the toolbar you want to display. A ch[...]

37 Create Map: creates a map file your GPS unit can use from an area defined by a map border. Create Map (Advanced) toolbar Draw Map Borders: d raws map borders as green rectangles. Draw Corridor Map Borders: draws irregularly-shaped magenta corridor bor- ders. Useful for areas that don't fit neatly into rectangle borders, or for making strip [...]

38 New Map Border File: clears or erases from the screen any map borders appearing on the Master Map. Open Map Border File: opens a map border file previ- ously saved by MapCreate. Save Map Border File: saves to disk any new or edited map borders displayed on the Master Map. Open Map: opens a map saved to disk. Save All: saves a map border file and[...]

39 Copy: copies text or a selected GPS data item from a waypoint list, route waypoint list or icon list to the Win- dows clipboard. Paste: inserts text from the Windows clipboard. Inserts a GPS data item from the Windows clipboard into its re- spective list window. (You cannot paste one type of GPS data into a list window for a different data type.[...]

40 Map Category Options. Move Left: click this to see additional area on the left side of the map (i.e., a given point will shift to the right, bringing into view an area that was previously off the left side of the map.) Move Right: click this to see additional area on the right side of the map (i.e., a given point will shift to the left, bringing[...]

41 For example, if you're simply taking a cross-country highway trip across several states, you can turn off categories such as rural roads and/or minor city streets. This should give you the navigation in- formation you need at a smaller file size. However, when file size is no problem, most users prefer to include as much detail as possible.[...]

42 Icon List Window Route List Window This window shows the routes on the Master Map in a text list format. The list contains the route name, number, total distance of the route and the number of waypoints that make up the route. To open this window click V IEW | R OUTE L IST . The route name can be edited in the window. To change the name: 1. Clic[...]

43 be edited either on the Master Map or in the list window. You can also insert and delete waypoints in a route. To edit, right-click the waypoint. To relocate a route waypoint on the Master Map by dragging: 1. Right-click on the waypoint and select M OVE W AYPOINT . 2. Move the mouse pointer with the waypoint to the new location. 3. Left-click to[...]

44 Trail List Window Tip: You can automatically create a route from a trail, and you can edit the resulting route, if you wish. For more information, see Create Route From Trail in the Help file's Command Reference. To convert a trail, right-click the trail name. Then, in the pop-up menu, click C REATE R OUTE F ROM T RAIL . Moving Around the M[...]

45 Tip: The mouse pointer's location in latitude and longitude is always shown in the status bar at the bottom of the MapCreate screen. Zoom Area There are several ways to zoom in and zoom out on the Master Map display. All are described in the Help file's Command Reference, but for now we'll describe just three. One fast and precise[...]

46 features. You have two ways to access these commands, so choose whichever is most convenient. You can click the Zoom In and Zoom Out buttons on the Map Naviga- tion toolbar. Zoom buttons on the Map Navigation toolbar Or you can click the Z-Out (zoom out) and Z-In (zoom in) buttons, lo- cated at the bottom right corner of the Master Map. Zoom Out[...]

47 NOTE: You can always use the Zoom-In or Zoom-Out buttons, no matter what other commands may be activated. Creating Rectangle Map Borders Making a Map Border is the first step in creating a map for your Lowrance or Eagle GPS unit. Here's how: (Refer as needed to the Tool- bar section on page 35.) 1. Center the Master Map display on the area [...]

48 If you are satisfied with this map border and want to finish processing it for use in your GPS unit, you can jump ahead to "Creating and Sav- ing a Custom Map," on page 52. However, you might want to check out the following two optional steps on estimating the size of the map, and saving the border as a Map Border File. Estimate Map Si[...]

49 Save Map Border File dialog box. 2. Type a name in the File Name text box and click S AVE . The file was placed in the "data" sub-folder located within the MapCre- ate folder on your hard drive. You can now start another map border (click the N EW M AP B ORDER F ILE button on the F ILE toolbar) or you can close MapCreate and return ano[...]

50 Creating Corridor Map Borders A corridor map lets you twist and turn your borders to enclose irregu- larly shaped geographic features. Here's how: (Refer as needed to the "Toolbars" section, beginning on page 35.) 1. Center the Master Map display on the area you want to include in your map. Click the C ENTER M AP cross-hair button[...]

51 Finished corridor map. 7. Now move the mouse pointer off at an angle, in the new direction needed to follow the irregular terrain. You'll see that the active corridor border box now rotates around the last anchor point you set. This lets you move off in any direction, with the new segment of the corridor attached to the previous segments. C[...]

52 N EW M AP B ORDER F ILE button (on the F ILE toolbar). Then click the Y ES button on the Clear All Borders dialog box. This will erase all corri- dor borders displayed on the Master Map. Edit Corridor Borders It's easy to edit a corridor map. To add a segment, use the Draw Corri- dor Map Border button and simply click inside an existing seg[...]

53 Read the message, and then click OK to continue. 3. A progress dialog box will appear while MapCreate extracts the nec- essary information and builds the Map File. Building Map Progress dialog box. 4. When the map has been built, the Save As dialog box appears. Note that the file size of the map is shown in the title bar and in the status bar at[...]

54 Congratulations, you've made your first Map File! Your map was placed directly on your MMC or Secure Digital card. If you wish to keep a copy of the file on your computer, use Windows Explorer to copy the Map File to the "data" sub-folder located within the MapCreate folder on your hard drive. Tips: • If you don't plan to c[...]

55 4. Move the mouse pointer so that the arrow point is where you want the waypoint. Click to set the waypoint. Move your mouse away, and you can see the waypoint, with the default name of "Wpt 001." Create a waypoint: First, find the location on the Master Map. The longer arrow shows the location of a public hunting area parking lot. Mov[...]

56 • If you want to reposition the waypoint, move the cross-hair pointer or the zoom area pointer over a waypoint and right-click. In the pop-up menu, click M OVE W AYPOINT , and the pointer grabs the way- point. Move it to the new position and click to set it there. • There are other ways to delete waypoints, and you can also change the symbol[...]

57 4. Move the mouse pointer so that the arrow point is where you want the icon. Click to set the icon. Move your mouse away, and you can see the icon. Create an icon: First, find the location on the Master Map. The bottom arrow shows the location of a public boat ramp on this river. Move the pointer arrow tip over the location (left) and click to [...]

58 • If you want to reposition an icon, move the cross-hair pointer or the zoom area pointer over the icon and right-click. In the pop-up menu, click M OVE I CON , and the pointer grabs the icon. Move it to the new position and click to set it there. • There are other ways to delete icons, and you can also change the symbol and location. For in[...]

59 1. Center the Master Map display on the area where you want to begin your route. C li ck th e C ENTER M AP cross-hair button then click the cross-hair mouse pointer on the area you want cen- tered. 2. If needed, click the Z OOM I N or Z OOM O UT buttons so you can see enough detail to accurately place the route waypoints. Tip: As you move along [...]

60 5. You can move off in any direction and the next waypoint will be linked in a straight line to waypoint 1. Relocate your mouse pointer along your intended route and click to create additional route way- points as needed. Basically, you will set a new waypoint every time you need to change direction. 6. To close the C REATE R OUTE command, right[...]

61 move the cross-hair pointer over a route waypoint and right-click. In the pop-up menu, click the D ELETE W AYPOINT command. MapCreate erases the waypoint and the magenta line linking the waypoint to the route. To erase the route legs but leave the waypoints: open the Route List window (shortcut key F3 ), right-click the route name, and in the po[...]

62 2. Type a name in the File Name text box and click S AVE . Congratulations, you've made your first GPS Data File! MapCre- ate saved the file to the program's default storage folder, which is: C:Program FilesLEIMapCreateData . Now you can use Windows Ex- plorer to copy or move the file to your MMC card. Remember, Wi nd o ws treats y[...]

63 topic " Transfer Custom Maps and GPS Data Files ." This is usually lo- cated in the Advanced Mode Operation section of the hand-held units, and in the Basic GPS Operations section of gimbal-mounted units. Those instructions will tell you how to load the GPS Data File into your unit's memory so that the waypoints and other items ap[...]

64 When you right-click a route name in the Route List Window, a pop-up menu appears. Click on Draw Borders Around Route to generate the border. In this example, we are creating a corridor map border for a route from Dallas to Corpus Christi, Texas. MapCreate draws a corridor map border following the route. See the illustrations below, showing the [...]

65 Tip: You can control the width of any corridor map. Click V IEW | M AP D ISPLAY O PTIONS , and the Map Display Options dialog box appears. Click Map Display Options to bring up the Map Display Options dialog box. Click on the M AP B ORDERS tab. Near the bottom of the box, drag the Cor- ridor Width slider bar left to decrease or right to increase[...]

66 Creating a Route From a Trail A trail is a line drawn on the map by your GPS unit as you travel. It's a record of the path you've taken, showing where you've been. This fea- ture is also called a plot trail. In the field, the trail will extend from your present position back to where you began recording the trail. Your GPS unit re[...]

67 This example shows a portion of Trail 2, recorded during a business trip from Afton, Oklahoma to Kansas City, Missouri. The trail appears as a green line on the Master Map. It follows Interstate 44 to Carthage, Missouri, then Highway 71 north toward Kansas City. For ea si er v iew - ing, roads, highways and other features have been turned off. 2[...]

68 MapCreate converts the green trail line into a magenta route line with red waypoints. It does this by transforming thousands of position points in this trail to 25 route waypoints. See the illustration below, showing the trail and route before and after the command is performed. Trail segment through Joplin before conversion to a route (left) an[...]

69 Appendix 1: MapCreate Command List Complete documentation on all MapCreate commands is available in the program's Help File. To access Help and its Command Reference s e c t i o n , p r e s s F 1 . An example entry from the Command Reference (for the Help Command) appears at the end of this command list. About MapCreate Arrange Icons Arrang[...]

70 Help Topics Command Menu: H ELP Submenu: n/a Menu Command: H ELP T OPICS Menu Command Sequence: H ELP |H ELP T OPICS Hot Key Sequence: Alt+H|H Shortcut Key(s): F1 Toolbar button: n/a The Help Topics command opens the on-line Help system in your de- fault web browser. Our help information is in HTML format, but it runs from the CD or your hard dr[...]

71 3. In the F IND WHAT : box, type the term , phrase or command you are looking for, adjust any options such as up or down, then click F IND N EXT . Search a Help document for the term "map border." Netscape 6 browser: 1. Click somewhere on the help page you intend to search. This makes sure your browser will search the correct page. 2. [...]

72 Notes[...]

73 Appendix 2: Map Category List This list contains the different categories of mapping information avail- able in MapCreate 6. These categories and their subcategories can be turned off or on. Only those categories turned on (displayed in the Mas- ter Map) will be included in Custom Map Files for your GPS unit. See Appendix 3 for symbols used to r[...]

74 Auto Parts/Service Banks/Financial Bars/Nightclubs Entertainment Fishing/Hunting Food Stores Gasoline Government Marine Services Medical Service Museums/Zoos Postal Service Places of Worship RV Parks/Services Shopping Sporting Goods/Wear Sports Transportation Universities/Schools POI-Lodging Bed & Breakfast Cabins Camps/Campgrounds Hotels/Mo[...]

75 County/Parish Boundaries Highway Exits Exits Information Centers Parking Areas Picnic Areas Rest Areas Scenic Areas Service Areas Toll Plazas Welcome Centers Weigh Stations Highways US International Minor International Major Interstate Symbols Interstate State State Symbols US Symbols Landmarks Buildings Cemeteries Fire Stations Land Features Li[...]

76 Water Canals/Streams Canals/Stream Names Lake/Rivers Lake/River Names Ocean/Seas Ocean/Sea Names Other Names Wrecks & Obstructions[...]

77 Appendix 3: MapCreate 6 Symbol Key MapCreate 6 contains hundreds of mapping symbols used to represent items ranging from geographic features to commercial Points of Inter- est (POI). The following list displays these symbols and the name of the item the symbol represents. Interstate Highway U.S. Highway State Highway Trans-Canada Highway Quebec [...]

78 Shopping Center Summit Tower Trail Name City, Community, or Subdivision Name Land Feature Name Water Feature Name Miscellaneous Landmark Name Square Green Daybeacon (Navaid) Square White or Unidentified Daybeacon (Navaid) Red Triangle Daybeacon (Navaid) White Triangle Daybeacon (Navaid) Green Lighted Buoy (Navaid) Red Lighted Buoy (Navaid) White[...]

79 Amusement Place, Billiards or Casino (POI) College or University (POI) Hall or Auditorium (POI) Hospital (POI) Medical Service (POI) Miscellaneous Attraction (POI) Museum or Historical Place (POI) Post Office Tourist Attraction or Tour (POI) Zoo (POI) Movie Theater (POI) Restaurant (POI) Coffee Shop (POI) Ice Cream Parlor (POI) Pizza (POI) Fishi[...]

80 Pharmacy (POI) Hardware Store (POI) Sporting Goods or Sportswear (POI) Golf-Related (POI) Park or Park Office (POI) Synagogue (POI) Church (POI) Police or Sheriff (POI) Bar or Club (POI) Live Theater (POI) Hunting-Related (POI) Car Wash (POI) Financial Service (POI) Bowling Center (POI) Swimming Pool (POI) Railroad (POI) Recreation Center, Stadi[...]

81 Appendix 4: Displaying Specialty Maps With Fishing or Aeronautical Data A new feature in MapCreate 6.3 allows you to view LEI's special fishing or aviation mapping products on the MapCreate screen. The feature works with Inland Mapping System  Fishing Hot Spots  fishing maps or Jeppesen  Americas and Jeppesen  International aero[...]

82 IMS Fishing Hot Spots Maps Master Map window showing detail from an IMS Fishing Hot Spots map of Lake Skiatook. Place the Center Map or Zoom Area pointer over an item and a pop-up information box appears. Move your mouse pointer over an item and a pop-up tool-tip box ap- pears, identifying the item. In a Lowrance or Eagle GPS unit, the cur- sor [...]

83 There are other important Fishing Hotspot symbols that display infor- mation only on your GPS unit. They are all accessed with the cursor and either the Wpt or Find key. These symbols are usually (but not al- ways) located near the dam site, and they include: Fishing Tips & Techniques: the Waypoint Information screen will display an article [...]

84 Jeppesen airspace data displayed in a MapCreate pop-up box. Point to an airport identifier and you'll see a pop-up box with the num- ber of communication frequencies, number of runways and number of services available at that field. Point to a runway, and you can see its length, surface type and lighting. Jeppesen airport (left) and runway [...]

85 Master Map window at the 60 mile zoom level showing detail from a Jeppesen Americas aeronautical database. Intersections appear as gray Xs; other symbols appear as they do in sectional paper charts.[...]

86 Notes[...]

87 Appendix 5: Considerations When Planning Highway Routes Tips on Making Better Routes for Highway Navigation How you make a highway route depends on your type of travel and whether you prefer to use the GPS unit's compass rose screen, the map screen or both for navigation. These factors determine how many route waypoints to use, and where yo[...]

88 on, and you have the option of turning the alarms' sound feature on or off as well.) The amazing capabilities of GPS navigation can tempt first-time users to build highly detailed highway routes. These "high res" routes are fun to use, but they have some drawbacks. They require placing a route waypoint at practically every curve i[...]

89 the twists and curves of the pavement as closely as a "high resolution" route would. For example, you could be traveling toward a destination to the south, but following a highway curve around a mountain. As you take the curve to your right, your car will actually be pointing west as you follow the pavement. However, the compass rose i[...]

90 Notes[...]

91 Index A Accessories, 9 Airspace, 83, 84 Alarms, 87, 89 Appendices 1, MapCreate Command List , 69 2, Map Category List , 73 3, MapCreate 6 Symbol Key , 77 4, Displaying Specialty Maps , 81 5, Considerations When Planning Highway Routes , 87 Arrival Alarm, 87 C Card Encryption, 52 Center Map, 39, 44, 45, 47, 50, 51, 54, 55, 56, 57, 59, 60, 69, 82,[...]

92 Position Format, 11 R Route, 5, 6, 11, 12, 16, 34, 37, 38, 39, 42, 43, 44, 49, 54, 56, 58, 59, 60, 61, 63, 64, 66, 67, 68, 69, 81, 87, 88, 89 Create, 58, 63, 66 Delete, 60 Runways, 73, 74, 84 S Save Map Border File, 38, 49, 69 Screen Components, 33 Create Map (Advanced) toolbar, 36, 37 Create Map (Easy), 36 File toolbar, 37, 48, 49, 52, 61, 64, [...]

93 Notes[...]

94 Notes[...]

95 LEI End User License Agreement THESE PRODUCTS (AS DEFINED BELOW) ARE OWNED BY LEI* AND ARE PROTECTED UNDER COPYRIGHT LAWS AND IN- TERNATIONAL COPYRIGHT TREATIES. THESE PRODUCTS ARE LICENSED, NOT SOLD. THESE PRODUCTS ARE PROVIDED UNDER THIS END USER LICENSE AGREEMENT ("LICENSE"), WHICH DEFINES WHAT YOU MAY DO WITH THE PRODUCTS, AND CONT[...]

96 any third party. Without limiting the generality of the foregoing, You will not Transfer the Products in connection with any commercial network services or interactive cable or remote processing services; c. You may not modify, port, adapt, translate, duplicate (except as ex- pressly permitted in this License), disassemble, reverse engineer, rev[...]

97 be available so long as you can show in a reasonable manner that the defect occurred within one (1) year from the date of your original purchase, and we must receive your warranty claim no later than 30 days after such 1- year period expires. Your claim must be substantiated by a dated sales re- ceipt or sales slip. In the event the software fai[...]

98 c. NOTWITHSTANDING ANYTHING TO THE CONTRARY CON- TAINED IN THIS LICENSE, LEI SHALL NOT BE LIABLE TO YOU OR ANY THIRD PARTY, TO THE EXTENT PERMITTED UNDER APPLI- CABLE LAW, FOR ANY INDIRECT, CONSEQUENTIAL, EXEMPLARY, PUNITIVE, MULTIPLE, INCIDENTAL, OR SPECIAL DAMAGES, LOST PROFITS, LOST SAVINGS, OR TO THE EXTENT PERMITTED BY LAW, DAMAGES RESULTIN[...]

99 product and not subject to disclosure. 9. Government Confidentiality. If You are or represent an agency, de- partment, or other entity of any State government, the United States Gov- ernment or any other public entity or funded in whole or in part by the United States Government, You hereby represent and warrant that the Products shall be protec[...]

100 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any product can be returned, you must call customer service to determine if a retur[...]

Accessory Ordering Information for all countries LEI Extras  , Inc. is the accessory source for sonar and GPS products manufactured by Lowrance Electronics and Eagle Electronics. To order MapCreate and GPS accessories such as MMC cards or MMC card readers, please contact: 1) Your local marine dealer or consumer electronics store. Most quality de[...]

Visit our web site: www.lei-extras.com For Lowrance  and Eagle  Products LEI Pub. 988-0147-383 © Copyright 2004 All Rights Reserved Printed in USA 051904 LEI[...]