Lowrance electronic 7300C HD manuel d'utilisation

Pub. 988-0151-521 www.lowrance.com GlobalMap ® 7200 C , GlobalMap ® 7300 C HD , GlobalMap ® 8200 C , GlobalMap ® 8300 C HD , GlobalMap ® 9200 C , GlobalMap ® 9300 C HD , Mapping GPS Receivers Operation Instructions[...]

Copyright © 2006 Lowrance Electronic s, Inc. All rights reserved. No part of this manual m ay be copied, reproduced, republished, transmitted or distribute d for any purpose, withou t prior written consent of Lowrance Electro nics. Any unauthorized commercial distribution of this manual is strictly prohibited. Lowrance ® is a registered trademark[...]

i Table of Contents Section 1: Read Me Fi rst! ......................................................... 1 How Lowrance GPS Works ........................................................... 3 Introduction to GPS and WAAS ................................................... 4 How to use this manual: ty pographical co nven tions .................. 7 S[...]

ii Navigate a Tra il (forwar d) ...................................................... 53 Navigate a Back Trail ( backtrack, or reverse ) ...................... 55 Transfer Custom Maps and GPS Data Files ............................. 56 Save GPS Data to Hard Dr ive .................................................... 58 Cancel Navi gation .........[...]

iii Coordinate System Select ion ...................................................... 76 Map Fi x ........................................................................................ 78 Customize Page Displa ys ............................................................ 79 GPS Simula tor ......................................................[...]

iv Units of Me asure ....................................................................... 108 Section 6: Searchin g............................................................. 109 Find Addr esses .......................................................................... 110 Find Any Item Selected by Map Cursor ..................................[...]

v WARNING! A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION. CAUTION When showing navigation data to a position (waypoint), a GPS unit will show the shortest, most direct path to the waypoi nt. It provides navigation data to the waypoint regardless of obstructions. Th erefore, the prudent navigator will not only ta[...]

vi Notes[...]

1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of GPS satellite navigation! We know you're anxious to begin finding your way with this space-age technol- ogy, but we have a favor to as k. Before you grab the GlobalMap ® and begin installing it, please give us a moment or two to exp[...]

2 Section 3 contains short, easy-to-scan GPS lessons that follow one an- other in chronological order. They're all you'll need to know to find your way on the water or in the wilderness quickly. After you've learned the basics (or if you already have some GPS ex- perience), you may want to try out some of the GlobalMap's many ad[...]

3 How Lowrance GPS Works You'll navigate faster and easier if you understand how the GlobalMap scans the sky to tell you where you are on the earth — and, where you're going (But if you already ha ve a working understanding of GPS receivers and the GPS navigation system, skip on ahead to Section 2, Installation & Accessories o n pa [...]

4 Think of this data storage like the hard drive memory in a computer or a tape in a cassette tape recorder. You can save several different GPS data files, erase 'em and record new ones, over and over again. Like any com- puter file, these GPS Data Files (file format *.usr) can be shared be- tween Lowrance GPS or sonar/GPS units or even person[...]

5 9, so you can mount your GlobalMa p and plug in the power. Or you might want to see how our text fo rmatting makes the manual tutorials easy to skim. If that's the case, move on to "How to Use This Manual" on page 7. But, if you want to understand the current state of satellite navigation, look over this segment describing how GPS [...]

6 Remember, the unit must have a clear view of the satellites in order to receive their signals. Unlike radio or television signals, GPS works at very high frequencies. These signals can be easily blocked by trees, buildings, an automobile roof, eve n your body. Like most GPS receivers, this unit doesn’t have a compass or any other navigation aid[...]

7 How to use this manual: typographical conventions Many instructions are listed as numbered steps. The keypad and arrow "keystrokes" appear as boldface type . So, if you're in a real hurry (or just need a reminder), you can skim the instructions and pick out what menu command to use by finding th e boldface command text. The fol- lo[...]

8 press and hold) the down arrow key to scroll down the menu and select (highlight) the My Trails menu command. Finally, press the Enter key." Step 2 would mean: "Press the down arrow key repeatedly to scroll to the trail named Trail 1, and press Enter. Next, press the right arrow key and then the down arrow key to highlight the Navigate [...]

9 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1. Determine the approximate location for the GPS unit, so you c[...]

10 You need to select an antenna installation location that has a clear, un- obstructed view of the sky. After the module is installed, connect it to the unit. The LGC-3000 can communicate with your GPS unit either directly (using the supplied extension cable) or through a NMEA 2000 ® network. NOTE: See the module’s instruction sheet, publicatio[...]

11 NOTE: There are two basic power connection options, which are shown in the following two diagrams. Read the following instructions carefully to determine which power connection applies to your unit. De- pending on your configuration, yo u may not use all of these wires. Caution: All of the wires in the power/data cable have bare ends for eas- ie[...]

12 this unit could be damaged to a point that it is irreparable and could even cause harm to the user when not properly fused. Failure to use a 3-amp fuse will void your warranty. If possible, keep the power cable away from other boat wiring, especially the engine's wires. This will provide the best isolation from electrical noise. If the cabl[...]

13 The network and any NMEA 2000 devices, including the GPS module, will not operate unless the NMEA 2000 Power Cable is connected to power. The NMEA 2000 power cable must be connected to power even if your only NMEA 2000 device is the GPS module and it is connected to the display unit's Network socket. (However, never con- nect multiple power[...]

14 use the method shown in Power Diagram B above. Never attach two power sources to a single NMEA 2000 bus. If you do need to power your NM EA 2000 bus, attach the NMEA 2000 Power cable to an accessory switch as in dicated in power diagram A. The NMEA 2000 Power cable's red wire should be a ttached (with provided 3-amp fuse) to the positive (+[...]

15 LGC-3000 and display unit as an expandable NMEA 2000 network. The diagram above has a double T connector with two 120-ohm termina- tors — one at each end of the connector. It is easy to expand this network by removing a terminator from one end of the double T connector, then inserting a new T connector or extension cable between the double T c[...]

16 Com-1 wiring to exchange information with another device. Com-2 wiring to exchange information with another device. Orange (Receive) Shield (Ground) Transmit Ground Com-1 To Unit To Other Device Y ellow (Transmit) Receive Green (Receive) Shield (Ground) Transmit Ground Com-2 To Unit To Other Device Blue (Transmit) Receive[...]

17 Cable connections, GlobalMap 7200 and GlobalMap 7300. Pow er/Data Netw ork LGC 3000 GPS Module NMEA 0183 Data cable ( five wires ) NMEA 2000 Pow er cable Display unit pow er cable Double T-connector 120-ohm male terminator 120-ohm female terminato r Ethernet (for later expansion) Extension cables[...]

18 Cable connections, GlobalMap 8200 and GlobalMap 8300 Ethernet (for later expansion) Pow er/Data Netw ork NMEA 0183 Data cable ( five wires ) 120-ohm female terminator LGC-3000 GPS Module NMEA 2000 Pow er cable Double T-connector 120-ohm male terminator Extension cables Display unit pow er cable[...]

19 Cable connections, GlobalMap 9200 and GlobalMap 9300. LGC-3000 GPS Module NMEA 0183 Data cable ( five wires ) NMEA 2000 Pow er cable Display unit pow er cable Double T-connector 120-ohm male terminator 120-ohm female terminator Extension cables Pow er/Data Netw ork Ethernet (for later expansion)[...]

20 Expanding to a NMEA 2000 Network A network bus is an installed and operational network cable (backbone) running the length of your boat, al ready connected to a power supply and properly terminated. Such a bus provides network connection nodes at various locations around your boat. The NMEA 2000 network is similar to th e telephone wiring in a h[...]

21 NOTE: If you have a double T Connector on your network that is not at- tached to a device, you must cap the unused connector with a NMEA 2000 cap. This will protect the pin connectors from corro- sion. The NMEA 2000 cap looks like a terminator, but has "Cap" stamped into the connector housing. Adding a Network Node You can add a node t[...]

22 NOTE: You do not need a Bus Adapter Cable with this unit if you use an approved Devicenet NMEA 2000 connector. Approved Devicenet NMEA 2000 connectors work with Lowrance red connector dis- play units and components, so no adapter cables are needed. Mounting the Unit: Bracket, In-Dash or Portable You can install the GlobalMap on the top of a dash[...]

23 Install the gimbal bracket. Place the bracket so the arms slope toward the front of your unit. Once a location is determined, use the bracket as a template and mark the mounting holes and the hole for the cables. Drill a 1-inch (25.4 mm) hole in the dash for the power, transducer and antenna cables. Screw the bracket to the mounting surface. Fro[...]

24 Front view (left) and side view (right) showing dimensions of the GlobalMap 8200c and GlobalMap 8300CHD mounted on gimbal brackets. Front view (left) and side view (right) showing dimensions of the GlobalMap 9200 and GlobalMap 9300 mounted on gimbal brackets. Millimeter [Inch] Millimeter [Inch][...]

25 To pass all connectors through the 1" hole, first pass the antenna con- nector up through the hole from under the dash. Next, pass the power cable's bare-wire end down though the hole from the top. If you wish, you can fill in the hole around the cables with a good ma- rine caulking compound. No matter what type of installation you pre[...]

26 easy to transfer your unit from a boat to a car, recreational vehicle, air- plane or other vehicle without drilling and mounting a second bracket. You can use your unit in your own car or boat, then take it along when riding in a friend's vehicle that's not equipped with GPS. The portable power pack includes a sealed, rechargeable batt[...]

27 Slide the drawer back into the unit an d twist the retainer clockwise. The MMC is now ready for use. In the GlobalMap 9200 and GlobalMap 9300, the two MMC slots are located in compartments on the front of the case. The water-proof compartment doors are located at the lower right corner. Th e following figure shows a close-up of one compartment w[...]

28 MapCreate™ 6 CD-ROM, left; MMC card reader for USB ports, right. Now that you have your GlobalMap in stalled, move on to Section 3, Ba- sic GPS Operations . There, we'll present a series of step-by-step tutori- als to teach you the basics of GPS navigation. Face Cover Your unit comes with a white protective cover that snaps on and off the[...]

29 Section 3: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 4 is a rranged in alphabetical order. Before you turn on the unit and fi[...]

30 1. PWR/LIGHT (Power & Light) – The PWR key turns the unit on and off and activates the backlight. 2. PAGES – Pressing this and the ← → arrow keys (4) switches the unit between the three different page screens (Satellite Status Page, Navigation Page, Map Page and Radar Page). Each page represents one of the unit's major operation[...]

31 out of the box with the factory default settings. But, if you want to learn about the various options, see Sec. 5, System Setup and GPS Setup Options . You can access the Main Menu from any of the three Page screens by pressing MENU | MENU . To clear the menu screen and return to the page display, press EXIT . Main Menu. The Main Menu commands a[...]

32 Trip Calculator command: shows trip status and statistics. Timers command: controls the up time r, down timer and alarm clock settings. Browse Files command: this allows you to view the installed MMC card and the files it contains. Pages The unit has four Page displays that represent the four major operating modes. They are the Satellite Status [...]

33 The Satellite Status Page. This screen shows a graphical view of the satellites that are in view. Each satellite is shown on the circular chart re lative to your position. The point in the center of the chart is directly ov erhead. The small inner ring represents 45° above the horizon and the large ring represents the horizon. North is at the t[...]

34 The navigation screen looks lik e the one below when you're not navi- gating to a waypoint or following a route or trail. Your position is shown by an arrow in the center of the screen. Your trail history, or path you've just taken, is depicted by the line extending from the ar- row. The arrow pointing down at the top of the c om pa s [...]

35 Bearing window shows the compass direction straight to the destina- tion from your location at the moment. Distance shows how far it is to the waypoint you're navigating toward. The Off Course window shows the current cross track error. This shows the distance you are off-course to the side of the desired course line. The course line is an [...]

36 In the example above, the driver is headed north (a 355º track) toward a way- point 355º (bearing) away. The cross trac k error range (white corridor) is 0.20 miles either side of the course. The driver is headed toward trail waypoint 4, which is 0.14 miles away. The vehicle is vi rtually on course (off course 1 foot to the right). Traveling a[...]

37 If you're using only the factory-loaded background map, the maximum zoom range for showing additional map detail is 20 miles. You can con- tinue to zoom in closer, but the map will simply be enlarged without revealing more map content (except fo r a few major city streets). Load your own high-detail custom map made with MapCreate, and you c[...]

38 landmark features (such as summits, schools, radio towers, etc.); more rivers, streams, smaller lake s and ponds and their names. What's more important is the large-scale map detail that allows your G P S u ni t t o s h o w a higher level of position accuracy. For example, the back- ground map would show you the general outline and approxim[...]

39 GlobalMap Digital Data page (left) and Two Position Formats page (right). Pages Menu with Two Maps option selected (left). Map Page with two map windows (right). The right map is active. In pages that have two major windows (such as two maps) you can toggle back and forth between the two windows by pressing PA GES | PAGES . This allows you to ch[...]

40 Map Menu with Resize Window command selected (left). Resize Win- dow command is active (center). Pressing the ← → or ↑ ↓ keys allows you to resize the windows from side to side or stack them one on top of the other (right). The following page contains a 12-step quick reference for the most basic GPS operations. If you don't want to [...]

41 GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navi- gating to a location at least a few blocks away. While you're learning, navigation in too small an area will constantly trigger arrival alarms. 1. Connect the unit to electric powe r and the antenna module. Make sure the MMC is in. (See complet[...]

42 Find Your Current Position Finding your current position is as simple as turning the GlobalMap on. With an unobstructed view of the sky, the unit automatically searches for satellites and calculates its position in approximately one minute or less. If for some reason satellite acquisit ion takes longer, you may be inside a structure or vehicle o[...]

43 The selected airport is 4.25 miles away, to the northwest. Selecting Any Map Item with the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired object. On most items, a pop-up box will give the name of the selected item. S[...]

44 Category Selection menu (left); list of the nearest restaurants (right). 4. If you wish, you could scroll ↑ or ↓ here to select another restaurant, but for now we will just accept the nearest one. Press ENT . 5. The POI information screen appe ars (This is how you can use the GlobalMap as a business phone directory!). If you wanted to naviga[...]

45 Map screen showing Find Waypoint, the result of a restaurant search. NOTE: Search works from mapping and POI data loaded in the Global- Map. If you do not have a high-detailed custom map (containing POI data) for the area you are searching loaded on the MMC, you may not find anything. Set a Waypoint A waypoint is simply an electronic "addre[...]

46 Sequence for setting a waypoint. Step 1: while traveling, quickly press WPT twice to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: ve- hicle continues on its way; number waypoint symbol is visible on map. NOTE: The Quick Save method uses the default waypoint symbol unti[...]

47 Create Way point by Entering a Position 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT . 2. Press ↓ to E NTERED P OSITION | ENT | → to C REATE | ENT . 3. Press → to L ATITUDE | ENT . Enter the latitude by pressing ↑ or ↓ to change the first character, then press → to the next character and re- peat until the latitude is[...]

48 GlobalMap navigation Page, navigating toward waypoint 004 and leav- ing a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. This situation can be deadly on any body of wa- ter. It's particularly dangerous at night or if you're out of sight of land. O[...]

49 Navigating to Man Overboard: navigation page (left) and Map Page (right). The victim is astern of the vessel; the GPS shows which direc- tion to steer to for the rescue. The man overboard position is also stored in the waypoint list for fu- ture reference. It can be edited the same as any other waypoint. T o c a n c e l n a v i g a t i o n t o M[...]

50 Navigate to cursor. In this example, the cursor is positioned on the town of Oologah, Oklahoma. 3. Press MENU | ENT and the GlobalMap will begin navigating to the cur- sor location. The Map Page will display a dotted line from your current position to the cursor position. The Navigation Page displays a compass rose showing navigation information[...]

51 After you have looked up an item with the Find Waypoint command, use the → to make sure the G O T O command is highlighted at the top of the screen, then press ENT . The GlobalMap begins showing navigation information to the item. To cancel navigation, press MENU | MENU | ↓ to C A NCEL N AV I G ATI O N | ENT | ← to Y ES | ENT . The unit st[...]

52 3. Press ↓ → to A CTIVE | ENT . This unchecks the Active option. 4. To return to the previous page, press EXIT | EXIT | EXIT | EXIT . As you left the Edit Trail menu, you will notice that a new trail was started with a new se- quential number. In the example below, the new trail is number 15, showing zero points. Note that Trail 14 is inacti[...]

53 To turn on trail display: 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de- sired Trail Name | ENT . 3. Press ↓ → to A CTIVE | ↓ to V ISIBLE | ENT . To return to the previous page, press EXIT | EXIT | EXIT | EXIT . Navigating Trails There are three methods fo[...]

54 NOTE: If you are already located at or near the beginning of your trail, the arrival alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm. 5. Begin moving and let your GlobalMap guide you. 6. When you reach your destination, be sure to cancel your navigation: press MENU | MENU | ↓ to C ANCEL N AVI G AT I ON | ENT . Th[...]

55 Navigate trail, map views: driver is northbound heading straight to- ward trail point 6 (left). northbound driver has reached point 6 (right) and has turned west to follow trail. Navigate trail, navigation page (compass rose) views: driver is north- bound heading straight toward trail point 6 (left); bearing arrow shows the trail point is due no[...]

56 NOTE: If you are already located at or near the end of your trail, the arri- val alarm will go off as soon as you hit ENT . Press EXIT to clear the alarm and proceed. 5. Begin moving and let your GlobalMap guide you. 6. When you reach your destination, be sure to cancel your navigation. Press MENU | MENU | ↓ to C ANCEL N AV I GAT I O N | ENT .[...]

57 The Transfer My Data submenu asks if you want to save data to the MMC or load data from the MMC into the unit's memory. 2. The Transfer My Data menu includes a message that tells you if a MM C i s p rese nt o r n ot. I f no MMC i s pr es en t, yo u mu st i ns ert a car d to activate the Load or Save commands. To transfer data from the Globa[...]

58 4. Loading to unit memory : There may be m ore than one GPS Data File (*.USR) on the card. To select a file, press ENT to activate the selec- tion box, use ↓ or ↑ to highlight the file, then press ENT to accept the selection. Next, press ↓ to L OA D D ATA | ENT . The unit will display a comple- tion message when the data transfer is finish[...]

59 3. Press ↓ to S AVE D ATA | Press ENT The data is now stored on the unit's hard drive. NOTE: If you do no have a MMC or SD card already in the unit, the data information will automatically save to the unit's hard drive. To retrieve the saved data information: 1. MENU | MENU| ↓ to B ROWSE F ILE | ENT| ENT 2. Scroll through the list [...]

60 Notes[...]

61 Section 4: Advanced GPS Operations Find Distance to Another Location 1. While on the Map Page press MENU | ↓ to F IND D ISTANCE | ENT . 2. To check the distance to a location, center the cursor over the desired posi- tion. A rubber band line appears, connectin g your current position to the cur- sor's location. The distance along that lin[...]

62 You can create an icon at the cursor position on the map, or at your current position while you are navigating. Create Icon on Map 1. Use the arrow keys to move the cu rsor to the location you want to mark with an icon. 2. Press ENT and the screen shows a Select Icon Symbol menu. 3. Press ← or ↑ or → or ↓ to select your icon symbol, then[...]

63 The Delete All Icons command will ask if you are sure. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol menu. Press ← or ↑ or → or ↓ to select the symbol to delete, then press ENT . A message appears saying all icons with the selected symbol have been deleted. Th[...]

64 Routes Created in the GlobalMap You can create a route by selecting existing waypoints from the way- point list or you can set a series of route waypoints on the map with cursor arrows and the Enter key. In this example, we'll create a route from the map. 1. From the N AVI G AT I ON P AG E , press MENU | ENT or from the M AP P AG E , press [...]

65 Route creation sequence (left to right) : Fig. 1. Set route waypoint (1) at 11th St. & 145th Ave. Fig. 2. Move cursor north to set point (2) at 145th & Admiral. Fig. 3. With point (2) se t, move cursor east to mark inter- state on-ramp with waypoint (3). In figures 2 and 3, notice the rubber band line extending from the previously set wa[...]

66 Tip: You can also delete all routes at once: 1. From the N AV I G ATI O N P AG E , press MENU | ENT or from the M AP P AG E press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Press ↑ → to D ELETE A LL | ENT | ← to Y ES | ENT . Edit a Route You can edit the route name if you wish. 1. From the N AV I G ATI O N P AG E , press MENU | ENT o[...]

67 Navigate a Route 1. From the N AVI G AT I ON P AG E , press MENU | ENT or from the M AP P AG E , press MENU | MENU | ↓ to R OUTE P LANNING | ENT . Route Planning command on Main Me nu (left); Routes menu (center); Edit Route menu (right) with navigate command is selected. 2. Press ↓ to select route name | ENT | ↓ to N AV I GAT E | ENT . 3.[...]

68 Navigating along a route: Fig. 1 shows the GlobalMap Navigation Page at the start of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived at Wp t 1; the arrival alarm has been trig- gered and the bearing arrow on the compass rose has turned to point east, toward Wpt 2. In Fig. 3 the traveler has turned ea[...]

69 Edit a Trail Name To edit a trail name: press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | ENT . Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct. Press ENT then EXIT | EXIT | EXIT | EXIT to return to the previous page display. Tip: You can quickly cal[...]

70 Edit Trail Menu with Pattern option selected (left). Edited trail with dotted line pattern (right). transparency Utilities Utilities are useful tools for traveling or for outdoor activities. Alarm Clock To get to the alarm clock menu: press MENU | MENU | ↓ to T IMERS | ENT | ↓ to A LARM C LOCK | ENT . Sun/Moon Rise & Set Calculator To ge[...]

71 Edit a Waypoint Waypoint Name To edit waypoint name: 1. Press WPT | ENT | ENT | ENT | ↓ to waypoint name | ENT | ↓ to E DIT W AYPOINT | ENT | ENT . 2. Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct. Press ENT then EXIT | EXIT | EXIT | EXIT to return to the previous pa[...]

72 Set a Waypoint by Projecting a Position This feature sets a waypoint at a point located a specific distance and bearing from a reference position. The reference position may be a map feature or can be selected from your waypoint or Points of Interest lists. 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT . 2. Press ↓ to P ROJECTED[...]

73 Section 5: System & GPS Setup Options Alarms This unit has three GPS alarms. The factory default setting has all the alarms turned on. You can turn the alarms off and on and change their distance settings. You can set an arrival alarm to fl ash a warning message and sound a tone when you cross a preset distance from a waypoint. For example, [...]

74 3. To change distance settings, scroll ↓ or ↑ to select the desired cate- gory, then press → | ENT to activate the distance dialog box. Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct. 4. When your adjustments are finished, return to the last page dis- played by repe[...]

75 GPS Auto Search on the GlobalMap Satellite Status Menu. Here's how to put the unit into auto search mode: 1. Press PAGES until you are on the Satellite Status screen. 2. Press MENU | ↓ to GPS A UTO S EA RCH | ENT | ← to Y ES | ENT . Check MMC Files and Storage Space To check MMC Files: Press MENU | MENU | ↓ to B ROWSE F ILES | ENT. Ma[...]

76 System Setup Menu with Communicati ons Port highlighted (left) and Communications Port menu (right). For assistance in configuring the unit to communicate with another device, consult the factory. Customer service phone numbers are in the back of this manual. Also see the entry below for to Configure NMEA . To set Com Port Configuration: 1. Pres[...]

77 Menus for changing coordinate system. To get to Coordinate System Selection: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT . 2. Press ↓ to C OORDINATE S YSTEM | ENT . This unit can show a position in degrees (36.14952°); degrees, minutes and thousandths of a minute (36° 28.700'); or degrees, minutes, seconds and tenths of a second (36?[...]

78 To setup Loran TD: NOTE: If the Loran TD conversion is chosen, you must enter the local Lo- ran chain identification for the master and slaves. Do this by select- ing "Setup Loran TD" at the bottom of the "Coordinate System" menu, press ENT , and select the ID. Press EXIT to clear this menu. Configure Loran TD menu. Map Fix M[...]

79 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT . 2. Press ↓ to C OORDINATE S YSTEM | ENT . 3. Press ↓ to S ETUP M AP F IX | ENT . The following screen appears, and M AP S CA LE is highlighted. Press ENT and enter the map's scale. This is generally at the bottom of a paper map. It's shown as a rati o, for example 1:24000. Press EXIT[...]

80 To change the information displayed in a data box: On the Page display you wish to change, press MENU | ↓ to C USTOMIZE | ENT| ENT . You'll see a list of categories with "+ " or "–" symbols next to each cate- gory. A category with a "+" is expandable , meaning its contents are hidden. Customize Menu, with t[...]

81 To get to the GPS Simulator: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT . 2. Press ↓ to S IMULATOR S | ENT . The GPS Simulator Menu appears. 3. Press ↓ to GPS S IMULATOR O N | ENT GPS Setup Menu (left); GPS Simulator menu (right). Make the desired settings, then turn the simulator on by highlighting the GPS S IM ULA TOR O N box and p[...]

82 4. Press EXIT to turn off the steering and speed boxes. The unit will now automatically "steer" along the trail or route. When you arrive at your "destination," cancel naviga tion as you normally do. Tip: You can pick any spot on the map to begin your simulation session by using the Initialize GPS command. This makes your uni[...]

83 which display latitude and longitude grid lines or range rings on the map. This menu lets you select Navionics Maps. For instructions, see the Navionics Charts entry in this section. To get to Map Data: From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Map Menu (left) and Map Data Menu (right). Earth Map Detail From the Map Page, press M[...]

84 Trackline Extension window are two check boxes (Show Time and Show Dis- tance) which allow you to turn on or o ff the time and/or distance settings. To set trackline extension: From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Press ↓ to T RA CKLINE E XTENSION | ENT. Use ↑ ↓ to select the desired distance setting and press ENT. Pre[...]

85 Map Datum Selection Maps and charts are based on a survey of the area that's covered by the map or chart. These surveys are called "Datums." Maps that are cre- ated using different datums will show the same latitude/longitude in slightly different locations. All datums are named. The GPS system is based on the WGS-84 da- tum, whic[...]

86 Map menu (left) and Map Categories Drawn menu (right). Map Orientation By default, this receiver shows the map with north always at the top of the screen. This is the way most maps and charts are printed on paper. Map orientation shown in north up (left) and track up (right). This is fine if you're always trave ling due north. What you see [...]

87 To change map orientation: from the Map Page, press MENU | ↓ to M AP O RIENTATION | ENT . Use ↑ or ↓ to select the desi red mode, then press ENT . Press EXIT | EXIT to return to the page display. Map Menu (left) and Map Orientation menu with the North Up map orientation option selected (right). NauticPath ™ USA Marine Charts Your unit ca[...]

88 2. Press WPT to display the Note Information screen. 3. To scroll through the Chart Note screen, use ↑ ↓ arrow keys to read the information. To return to the main page display, pre ss EXIT repeatedly. Entrance to Aransas Pass on a NauticPath chart with 8-nautical mile zoom (left). Remaining images (left to right): same position at 4- nautica[...]

89 3. To scroll through the service information window, use ↑ ↓ to see the types of services available. To return to the main page display, press EXIT repeatedly. Port Services information. Tidal Current Information NauticPath charts contain Tidal Current information, represented at large zoom ranges by a box icon with the letter " C .&quo[...]

90 NauticPath chart showing Tidal Current Station icon selected by cur- sor (left). Tidal Current animated icon at .8-nautical mile range. Current Information screen. The Tidal Current Information screen displays daily tidal current data for this station on this date at the present time. The graph at the top of the screen is an approximate view of [...]

91 To select another date: 1. Use ← → to highlight month, day or year, then press ENT . 2. Use ↑ ↓ to select the desired mont h, day or year and press ENT . To clear the information screen, press EXIT . Tide Information NauticPath charts contain Tidal Information, repre- sented at large zoom ranges by a box icon with the letter " T .&q[...]

92 Tide Information screen. The Tide Information screen displays daily tidal data for this station on this date at the present time. The gr aph at the top of the screen is an approximate view of the tidal range pattern for the day, from midnight (MN) to noon (NN) to midnight (MN). The dotted line across the graph is the Mean Lower Low Water line (M[...]

93 To display a Navionics chart: 1. Install the Navionics MMC in the memory card compartment and turn on the unit. (For full card install instructions, see Sec. 2.) 2. From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to M AP C HOICE | ENT . Select the Map Name , then pre ss ENT | EXIT | EXIT . Navionics Map Choice highlighted. Press En[...]

94 commands is that Customize changes only the digital data boxes on a screen, and Overlay Data changes only the information floating on the screen without a box. See Custom ize Page Displays, on page 79 for information on customizing data boxes. Overlay Data highlighted on GPS menu (left). The Data Viewer menu with the Navigation category expanded[...]

95 From Overlay Data Shown menu (left) press ENT to see Data Viewer (center). Select a category and press ENT . Bearing, Closing Speed and Off Course have been selected from the Navigation category. To remove overlaid data: 1. While on the Page that shows the item or items you want to remove, press MENU | ↓ to O VERLAY D ATA | ENT . 2. You'l[...]

96 3. The data begins to flash on yo ur screen. Use any combination of → , ← , ↑ and ↓ to move the data to a new location on the screen. 4. When satisfied, press EXIT | EXIT . To resize overlaid data: press MENU | ↓ to O VERLAY D ATA | ENT . This will bring up the Overlay Data Shown menu with a list of the current over- lay data. Use → [...]

97 Gauge Setup Menu. There are four primary setup options in the analog menu: Th emes, Tick Marks, Thresholds and Text. When working in the gauge setup menu, use ↓ ↑ and → ← to highlight the desired option, then press ENT . Pressing EXIT will take you back to the previous screen. NOTE: You can make gauges transparent from all the setup menu[...]

98 Minimum or Maximum Tick controls how many tick marks will be dis- played on the gauge. If you set the minimum tick to 1 and the max tick to 10, there will be 10 tick marks between 0 and 10, 10 and 20 and so on. In the case of a speedometer, that's one tick for one m ile per hour. If you change the minimum tick to 2 and leave the maximum tic[...]

99 NOTE: The Analog setup menus allow you to make gauges transparent. De- spite their transparency, the gauges take up much of the display screen. A display with a transparent track gauge (left). The screen on the right is displaying Track and speed gauges. Pop-up Help Help is available for virtually all of the menus on this unit. By high- lighting[...]

100 Reset Options To reset all features to their factory defaults: Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to R ESET O PTIONS | ENT | ← to Y ES | ENT . NOTE: Reset Options does not erase waypoints, routes, icons or plot trails. Reset Options command (left) and the Reset Options menu (right). Screen Contrast and Brightness To access [...]

101 To adjust the screen's display mode: Press ↓ to D ISPLAY M ODE | ENT |press ↑ or ↓ to select mode | EXIT . Display Mode menu. Set Language This unit's menus are available in 10 languages: English, French, Ger- man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish. To select a different language: 1. Press MENU | MENU[...]

102 To set the Day: Press → to D AY | ENT . Press ↑ or ↓ to select the day, then press ENT . To set the Year: Press → to Y EAR | ENT . Press ↑ or ↓ to select the year, then press ENT . Time Settings Menu. To Set Time Format : Press ↓ to the Time Format window. Just highlight the option you prefer — 12 or 24 hour — and press ENT . [...]

103 2. With the option highlighted, press ENT to uncheck it (turn off) and check it (turn on). After the option is set, press EXIT | EXIT to return to the page display. 3. You can return to this command and press ENT again to turn on the feature. Software Version Information From time to time, Lowrance update s the operating system software in some[...]

104 Sounds command (left); The Sounds menu (right). Once in the Sounds menu: To set Key Press Sounds: With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off). After the option is set, press EXIT | EXIT to return to the page display. To set A larm Sounds : Press ↓ to A LA RM S OUNDS . With the option high- lighted, p[...]

105 Trail Options There are several options you can use wi th trails. Some affect all trails, other options can be applied to a particular trail. You can change the way trails are updated, you can displa y or hide trails, make them flash, create a new trail, delete a trail, etc. General Trail Options To access the Trails Menu: Press MENU | MENU | ?[...]

106 range from 0.01 mile/nm/km to 9. 99 mile/nm/km. The default is 0.10 miles. With one of the Update Criter ia selected, use the cursor arrows to highlight either the U PDA TE R AT E or U PDATE D ISTANCE data entry boxes and press ENT . Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the entry [...]

107 New Trail To manually start a new trail, in the Trails Menu, make sure N EW T RA IL is highlighted and press ENT | EXIT . Trail Visible/Invisible and Other Trail Options The name, maximum number of po ints in the trail, activity, and visibil- ity are all changed on the Edit Trail menu screen. The Active setting determines whether or not the uni[...]

108 Units of Measure This menu sets the speed and distance (statute or nautical miles, me- ters), depth (feet, fathoms, or meters), temperature (degrees Fahren- heit or Celsius) and heading (true or magnetic) units. To change units: Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ENT . The Units of Measure menu. To set Speed/Distance Unit of Meas[...]

109 Section 6: Searching NOTE: The Search function depends on the type of map data loaded in your unit. GlobalMap HD models are fully "searchable" out of the box be- cause they contain a hard drive loaded with complete mapping in- formation. These maps include all the data contained in our Map- Create custom maps, Fishing Hot Spots lake m[...]

110 Find Addresses 1. From the Map Page, press MENU | ↓ to F IND A DDRESS | ENT . 2. Press ENT to search in the Address field. Find Address Menu. 3. T o enter an address n umber , press ↑ or ↓ to change the first number, then press → to move the cursor to the next number and repeat until the number is correct, then press ENT . 4. To enter a[...]

111 rect, then press ENT | ENT . B. Or jump down to the lower selection list by pressing ENT , then press ↓ or ↑ to select a city name from the list, then press ENT . The city name you selected is no w in the city field. NOTE : We recommend you do not enter a city name unless the list is too large when searching without one. The GlobalMap can a[...]

112 Tip: If the address happens to be an item in the Point of Interest data- base, you can look up the item's phone number in the POI informa- tion window. With the address location selected by the cursor on the map, press WPT . The POI's Waypoint Information window ap- pears, with the Go To Waypoint command highlighted. If you want to na[...]

113 Find Interstate Highway Exits 1. From the Map Page, press MENU | ↓ to H IGHWA Y E XITS | ENT , which calls up the Find Exit menu. Find Highway Exits command (left) and Find Exit menu (right). 2. First, select a highway name by pressing ENT , which calls up the Find By Name menu. There are two highway search options: A. You can spell out the h[...]

114 Find Exit menu, with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. A. Press ENT to navigate or "Go To" the exit. B. Press → | ENT to find exit on the map. Go To Exit option (left) and Find On Map option (right). Tip: You can also look up some additional information on the Exit Services lo[...]

115 Find Map Places or Points of Interest (POI) 1. Press WPT , then use ↓ or ↑ to select a map place or POI category, then press ENT (To narrow your search, press → then press ↓ or ↑ to select a subcategory before pressing ENT ). You will be given two op- tions; Search By Name or By Nearest. Find Waypoint menu with Lodging POI category se[...]

116 Find by Name option (left) an d Find by Name menu (right). 4. When the POI's Waypoint Information screen is displayed, you can choose to "Go To" the POI waypoint by pressing ENT or find it on the map by pressing → | ENT . Go To Waypoint POI option (left) an d Find on Map POI option (right). Find Streets or Intersections Find a [...]

117 2. You must first fill in a street name in the First Street dialog box. Press ENT to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next letter. Repeat until the name is correct, then press ENT |[...]

118 Map Page showing results of a street search. The cursor points to the located street. If you want to navigate to the found street at the cursor location, just press MENU | ENT | EXIT . Find an Intersection You must enter one street in the First Street dialog box and enter the next street in the Second Street dialog box. 1. From the Map Page, pr[...]

119 5. The Find Streets menu reappears with the first and second street dialog boxes filled in. In this exampl e, we selected 71st Street as our second street. You could now use simila r techniques to select a city or Zip code, but your search will probably be faster if you leave those boxes blank. You can specify a city and/or Zip code later to na[...]

120 Find Waypoints 1. Press WPT | ENT . 2. If searching for the waypoint By Name , press ENT . If searching for the Nearest waypoint, press ↓ to N EAREST | ENT (To search by name, jump to step 5 below.). Find Waypoint menu (left), Find By Nearest command (center) and Find by Name command (right). 3. If you're looking for nearest waypoint, th[...]

121 Waypoint Information screens with the Go To Waypoint command se- lected (left) and the Find on Map command selected (right). To clear these menus and return to the previous page, press EXIT re- peatedly. 5. If you're looking by name , there are two options: A. You can spell out the name in the top selection box. Press ↑ or ↓ to change [...]

122 Notes[...]

123 Section 7: NMEA 2000 Device Configuration NMEA 2000 Menu The NMEA 2000 menu on your display unit's main menu allows you to configure, calibrate and monitor devices on a NMEA 2000 network. The NMEA 2000 menu provides access to the Bus Setup, Fuel Management and NMEA 2000 Alarms. You also can turn on/off Waypoint Sharing and Backlight Synchr[...]

124 The NMEA Diagnostics page displays information about the perform - ance of the network bus, keeping you updated on bus status, mode, er- rors and bus traffic. The Ethernet Diagnostics page keeps you updated on the performance of an Ethernet connection (if applic able) supplying information ranging from IP Address to upload and download rates (b[...]

125 Tank Select The Tank Select menu allows you to choose from up to three tanks (Port, Center and Starboard), depe nding on the Engine-tank configura- tion that has been selected. This allows you to set up each tank indi- vidually. Tank Size The Tank Size menu allows you to inpu t the size of a selected tank in gallons. After selecting the desired[...]

126 8. Repeat Steps 5-7 for each remaining tank. 9. When all tanks have been configured, press the S ET C ONFIGURATION but- ton. The following confirmation message will appear: Are you sure you wish to change the bus configuration? Choose Y ES and press ENT , Press EXIT to get back to the main display. Device Configuration Menu When a device is sel[...]

127 Engine & Configuration menu, Tank Select menu, Tank Size dialog and Set Configuration button will not be displayed on the Bus Con- figuration menu. Fuel Management Menu The Fuel Management menu gives you access to the following options: Tank Location, Fuel Added, Add Fu el, Fill Tank, Engine Select, Reset Calibration, Reset Trip and Reset S[...]

128 Adding Fuel to Tank Tank Location, Fuel Added and Add Fuel commands work together to keep NMEA 2000 fuel data consistent with the actual amount of fuel added to the fuel tank(s). 1. Press MENU | MENU , select NMEA 2000 and press ENT . 2. The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Management, NMEA 2000 Alarms, Waypoint Sha[...]

129 4. Highlight R ESET C ALIBRATION and press ENT . The following confirma- tion message will appear: Are you sure you wish to Reset Calibration? Select Y ES and press ENT . Calibration settings for the selected fuel have been returned to factory defaults. To Reset Trip: The Reset Trip function allows you to reset to zero the running total of fuel[...]

130 5. To set the alarm percentage, press → to highlight P ERCENT and press ENT . 6. Use ↑ ↓ , ← → to input the desired percentage and press ENT . Repeat Steps 3-4 to set the other alarm. 7. Highlight S ET C ONFIGURATION and press ENT to finalize alarm settings. Press EXIT repeatedly to get back to the main display. NOTE: To turn off (unc[...]

131 2. Highlight B US S ETUP and press ENT , which will open the Bus Configu- ration menu. A list of network device s will be at the top of the page. 3. Select the temp sensor yo u want to rename and press ENT . The De- vice Configuration menu will appear with the Device Name dialog box highlighted. 4. Press ENT and use ↑ ↓ , ← → to input t[...]

132 Restore Defaults The Restore Defaults command allows you to reset an individual EP-35 Temp Sensor's settings to factory defa ults. If, for example, you execute the Restore Defaults command from your Water Temp's Advanced Options menu, only the settings for the Water Tem p will be reset to factory de- faults. Other temps on the network[...]

133 4. Select L OCATION and press ENT , which will open the Location menu with following options: Port, Center, Starboard and Unknown. 5. Highlight the desired location and press ENT . The following message will appear: Are you sure you wish to change this device's configuration? 5. Select Y ES and press ENT . Press EXIT repeatedly to get back[...]

134 EP-15 Fluid Level Configuration To input Devic e Name: 1. Press MENU| MENU , use ↑ ↓ to select NMEA 2000 and press ENT . The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight B US S ETUP and press ENT , which will open the Bus Configu-[...]

135 5. Select the desired fluid type and press ENT . The following message will appear: Are you sure you wish to change this device's configuration? 6. Highlight Y ES and press ENT . Press EXIT repeatedly to get back to the main display. To input Tank Size: 1. Press MENU| MENU , use ↑ ↓ to select NMEA 2000 and press ENT . The NMEA 2000 men[...]

136 To restore default se ttings: 1. Press MENU| MENU , use ↑ ↓ t o s e l e c t NMEA 2000 and press ENT . The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight B US S ETUP and press ENT , which will open the Bus Configu- ration menu. A lis[...]

137 4. Highlight L OCAT ION and press ENT , which will open the Location menu with the following options: Port, Center, Starboard and Unknown. 5. Select the desired location and press ENT . The following confirmation mes- sage will appear: Are you sure you wish to change this device's configuration? 6. Press ENT . Press EXIT repeatedly to get [...]

138 To restore default se ttings: 1. Press MENU| MENU , use ↑ ↓ t o s e l e c t NMEA 2000 and press ENT . The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight B US S ETUP and press ENT . 3. Use ↑ ↓ to select the desired fluid level an[...]

139 7. Highlight N O and press ENT . 8. Take your vessel out on the water and burn at least five gallons of fuel. Be sure you run only ONE engine — the engine connected to your fuel flow. 9. Fill up your tank again, noting how much fuel you added to the tank. Compare that number to the Fuel Used figure displayed on the page you customized. If the[...]

140 EP-15 Fluid Level Calibration The default calibration for the EP-15 Fluid Level is just as accurate as standard fluid level gauges. If, ho wever, the tank has an irregular shape or greater accuracy is needed, calibration is recommended. There are three calibration options: 2-Point, 3-Point and 5-Point. 2-Point Calibration A 2-point calibration [...]

141 Calibrate is highlighted on the device configuration menu (left). Cali- bration menu (right) with calibration instructions listed at the top. 3-Point Calibration 3-point calibration is designed for tanks that vary in shape from the top to the bottom. You can begin calibration at any point in the 3-point process, but we recommend starting calibr[...]

142 Num Pts menu with 5-point calibratio n selected (left). Half level se- lected on Fluid Level menu (center). Calibration Done window (right). 5-Point Calibration 5-point calibration is best suited tanks that vary greatly in shape from top to bottom. You can begin calibration at any point in the 5-point cali- bration process. We recommend star ti[...]

143 11. Highlight C ALIBRA TE and press ENT . The following message will ap- pear: Half Level Calibration Completed . Press ENT . 12. Add another quarter tank of fuel, which should raise the fuel level to 3 quarters of a tank. Highlight F LUID L EVEL and press ENT . Select 3 Q TR L EVEL and press ENT . 13. Select C ALIBRATE and press ENT . The foll[...]

144 NOTE: You must use the gauge's Fill Tank comm and when filling your fuel tank to keep the engine interfac e updated with correct information on the amount of fuel in the tank. To calibrate a Suzuki Engine Interface: 10. If calibration is necessary, press MENU | MENU , select NMEA 2000 and press ENT . 11. Highlight F UEL M AN AGE M E N T an[...]

145 3. Highlight A DVANCED O PTIONS and press ENT . Select Reset T RI M C ALIBRA- TION and press ENT . The following message will appear: Do you wish to re-calibrate the device? 4. Highlight Y ES and press ENT . Press EXIT repeatedly to get back to the main display. Bennett Trim Tabs Calibration Trim Tabs will be calibrated through their Device Con[...]

146 4. Select All Engines or the engine connected to the desired device and press ENT . 5. Highlight R ESET C ALIBRATION and press ENT . The following message will appear: Are you sure you wish to Reset Calibration? 6. Highlight Y ES and press ENT . Press EXIT repeatedly to get back to the main display.[...]

147 Section 8: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adindan Sudan Afgooye Somalia Ain el Abd 1970 Bahrain Ain el Abd 1970 Saudi Arabia Anna 1 Astro 1965 Cocos Islands Antigua Island Astro 1943; Antigua (Lee[...]

148 Chua Astro Paraguay Corrego Alegre Brazil Dabola Guinea Djakarta (Batavia) Indonesia (Sumatra) DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gi- braltar, Greece, Italy, Luxembourg, Nether- lands, Norway , Por- tugal, Spain, Swe- den, S[...]

149 Naparima BWI Trinidad & Tobago North American 1927 Mean for Antigua, Barbados, Barbuda, Caicos Islands, Cuba, Dominican Republic, Grand Cayman, Jamaica, Turks Islands North American 1927 Mean for Belize, Cos- ta Rica, El Salvador, Guatemala, Hondu- ras, Nicaragua North American 1927 Mean for Canada North American 1927 Mean for CONUS (Contin[...]

150 Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS 85 Soviet Geodetic Sys- tem 1985 South American 1969 Mean for Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Trinidad [...]

151 Notes[...]

152 Notes[...]

153 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful in- terference, and (2) this device mu st accept any interference re- ceived, including interference that may cause undesired opera- tion. Cha[...]

154 Notes[...]

155 LOWRANCE DATABASES LICENSE AGREEMENT THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS, INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US"). USING THE PRODUCT ACCOMPANIED BY T[...]

156 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Lowrance Electronics, Inc., the manufactur er of this product. "You" or "your" refers to the first person who purchases the prod- uct as a consumer item for personal, family, or household use. Th e Databases Limited Warranty applies to th[...]

157 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRAN CE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person wh o purchases this p roduct as a consumer item for personal, family or household use. We warrant this product agai[...]

158 How to Obtain Service… …in the USA: We back your investment in quality pr oducts with quick, expert service and genuine Lowrance parts. If you're in the United States and you have technical, return or repair qu estions, please contact the Factory Customer Service Department. Befo re any product can be returned, you must call customer s[...]

Accessory Ordering Information for all countries To order Lowrance accessories such as power cables or antennas, pleas e contact: 1) Your local marin e dealer or consumer electronics store. Most quality dealers that handle mar ine electronic equipment or other consumer electronics shou ld be able to assist you with these items. To locate a Lowrance[...]

Visit our web site: Lowrance Pub. 988-0151- 521 © Copyright 2006 All Rights Reserved Printed in USA 120806 Lowrance Electronics, Inc.[...]