Lowrance electronic M68C IceMachine manuel d'utilisation

Pub. 988-0152-031 www.lowrance.com M68C S/Map & M68C IceMachine Fish-finding Sonar & Mapping GPS Installation and Operation Instructions [...]

Copyright © 2003 Lowrance Electronics, Inc. All rights reserved. Lowrance ® is a registered trademark of Lowrance Electronics, Inc. Marine-Tex  is a trademark of Illinois Tool Works Inc. Lowrance Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without n[...]

i Table of Contents Sec. 1: Read Me First! .............................................................. 1 Capabilities and Specifi cations: M68 ............................................ 3 How your Sonar Works ................................................................. 4 How your GPS Works .................................................[...]

ii Depth Range - Manual................................................................ 50 Turn Auto Depth Range on Again: ..................................... 50 Depth Range - Upper and Lower Limits ................................... 50 FasTrack  .................................................................................. 52 Fish I.D. ?[...]

iii GPS Quick Reference ............................................................. 91 Find your Current Position ........................................................ 92 Moving around the Map: Zoom & Cursor Arrow Keys.............. 92 Selecting any Map Item with the Cursor .................................. 93 Set a Waypoint .............[...]

iv Trip Down Timer................................................................... 116 Trip Up Timer ....................................................................... 117 Waypoints .................................................................................. 117 Delete a Waypoint .......................................................[...]

v Delete Trail ........................................................................... 140 New Trail ............................................................................... 140 Trail Visible/Invisible and Other Trail Options .................. 141 Transparency ............................................................................ [...]

vi Notes[...]

1 Section 1: Read Me First! How this manual can get you out on the water, fast! Welcome to the exciting world of digital sonar and GPS! We know you're anxious to begin finding fish, but we have a favor to ask. Before you grab the unit and begin installing it, please give us a moment or two to explain how our manual can help you get the best pe[...]

2 dex, or just flipping through Section 3 or scanning through the sonar op- tions in Section 4. Section 5 is a brief introduction to the powerful ice fishing applications of the M68C and M68C IceMachine. (See section 2 to learn how you can get the most out of your M68C with the addition of a special portable power pack for ice fishing.) If you&apos[...]

3 Capabilities and Specifications: M68 General Display: ............................ High-contrast Film SuperTwist LCD. Diago- nal viewing area: 3.5" (8.9 cm). Resolution: ...................... 160 pixel x 240 pixel resolution; 38,400 total pixels. Backlighting: .................. LED ba ck li t sc re en wi th mu lt ip le lighting l e v- els;[...]

4 GPS Receiver/antenna: ......... Internal 12 parallel channel GPS/WAAS. Position updates: .......... Every second. Position points: ............. 1,000 waypoints; 1,000 event marker icons. Man Overboard: ............. MOB feature precisely marks man overboard location with special icon, then automatically displays navigation data to that position.[...]

5 display, where an image of the object appears on the scrolling sonar chart. The sonar's microprocessor calculates the time lapse between the transmitted signal and echo return to determine the distance to the object. The whole process repeats itself several times each second. How Your GPS Works You'll navigate faster and easier if you u[...]

6 WAAS work together to get you where you're going. The Global Positioning System (GPS) was launched July 17, 1995 by the United States Department of Defense. It was designed as a 24- hour-a-day, 365-days-a-year, all weather global navigation system for the armed forces of the U.S. and its allies. Civilian use was also avail- able at first, bu[...]

7 Like most GPS receivers, this unit doesn’t have a compass or any other navigation aid built inside. It relies solely on the signals from the sat- ellites to calculate a position. Speed, direction of travel, and distance are all calculated from position information. Therefore, in order for the unit to determine direction of travel, you must be m[...]

8 menu command to use by finding the boldface command text. The fol- lowing paragraphs explain how to interpret the text formatting for those commands and other instructions: Arrow Keys The arrow keys control the movement of dotted cross-hair lines on your mapping screen called the cursor. The arrow keys also control a hori- zontal line depth curso[...]

9 Section 2: Installation & Accessories Preparations You can install the sonar and GPS systems in some other order if you prefer, but we recommend this installation sequence: CAUTION: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1. Determine the approximate location for the sonar/G[...]

10 Remember, the transducer location and installation is the most critical part of a sonar installation. Recommended Tools and supplies If you prefer the option of routing the cable through the transom, you will need a 5/8" drill bit. NOTE: The following installation types also call for these recommended tools and required supplies that you mu[...]

11 boat hulls have a flat keel pad that offers a good mounting surface. On vee hulls, try to place the transducer where the deadrise is 10 ° or less. Left, vee pad hull; right, vee hull. A pod style transducer is shown here, but the principle is the same for Skimmers inside a hull. 4. If the transducer is mounted on the transom, make sure it doesn[...]

12 Align transducer centerline with hull bottom. However, there are times when you may need to adjust the transducer slightly higher or lower. (The slots in the mounting brackets allow you to loosen the screws and slide the transducer up or down.) If you fre- quently lose bottom signal lock while running at high speed, the trans- ducer may be comin[...]

13 Second, the transducer angle cannot be adjusted for the best fish arches on your sonar display. (This is not an issue for flasher-style sonars.) Lack of angle adjustment can be particularly troublesome on hulls that sit with the bow high when at rest or at slow trolling speeds. Third, a transducer CAN NOT shoot through wood and metal hulls. Thos[...]

14 Reassemble the transducer and bracket and place them against the transom. Again, check to see if you can move the transducer so it's parallel with the ground. If you can, then go to step 3. If it doesn't, repeat step 2, but use a different alignment letter until you can place the transducer on the transom correctly. Insert bolt and che[...]

15 Position transducer mount on transom and mark mounting holes. Side view shown at left and seen from above at right. 5. Attaching transducer to transom. Remove the transducer from the bracket and re-assemble it with the cable passing through the bracket over the bolt as shown in the following figures. Route cable over bolt and through bracket. Si[...]

16 6. Route the transducer cable through or over the transom to the sonar unit. Make sure to leave some slack in the cable at the tra nsd uce r. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from the engine's wiring, bilge pumps, VHF radio wires and cables, and aerators can be picked up by the son[...]

17 3. Route the transducer cable alongside the trolling motor shaft. Use plastic ties (not included) to attach the transducer cable to the troll- ing motor shaft. Make sure there is enough slack in the cable for the motor to turn freely. Route the cable to the sonar unit and the trans- ducer is ready for use. Transducer mounted on trolling motor, s[...]

18 If the arch slopes up – but not back down – then the front of the trans- ducer is too high and needs to be lowered. If only the back half of the arch is printed, then the nose of the transducer is angled too far down and needs to be raised. NOTE: Periodically wash the transducer's face with soap and water to re- move any oil film. Oil a[...]

19 Testing Determines Best Location Ideally, the shoot-thru transducer should be installed as close to the transom as possible, close to the centerline. This will give you the best performance during high speed maneuvers. Shoot-thru-hull transducer locations for high speed or trolling speed operation. To choose the proper location for shoot-thru-hu[...]

20 2. Next, take the transducer out of the water and place it in the water in the sump of the boat, face down. (The transducer face is shown in the figure on the following page.) Notice how the signal strength de- creases. The second bottom signal will probably disappear and the bot- tom signal intensity will likely decrease. 3. Now move the transd[...]

21 Epoxy transducer to hull. WARNING: Use only the epoxy available from LEI. It has been for- mulated to work with these installation procedures. Other epoxy types may be too thin or may not cure to the right consistency for optimum transducer performance. 2. The epoxy consists of the epoxy itself and a hardener. Remove the two compounds from the p[...]

22 5. After the epoxy has cured, route the cable to the sonar unit and it's ready to use. POWER AND CABLE CONNECTIONS The unit works from a 12-volt battery system. For the best results, at- tach the power cable directly to the battery. You can attach the power cable to an accessory or power buss, however you may have problems with electrical i[...]

23 lead, black is negative or ground. Make sure to attach the in-line fuse holder to the red lead as close to the power source as possible. For example, if you have to extend the power cable to the battery or power buss, attach one end of the fuse holder directly to the battery or power buss. This will protect both the unit and the power cable in t[...]

24 In-dash mounting template for M68. NOTE: This figure is not printed to scale. Bracket Installation Mount the unit in any convenient location, provided there is clearance when it’s tilted for the best viewing angle. You should also make sure there is enough room behind the unit to attach the power/transducer cable. (See the following drawings, [...]

25 Front view (left) and side view (right) showing dimensions of the M68 when mounted on quick release bracket. If you wish, you can fill in the hole around the cable with a good marine sealant compound. (Some marine dealers stock cable hole covers to con- ceal the opening.) This unit uses a quick release mounting bracket. When you run the ca- ble [...]

26 M68 quick release mounting bracket. Slots in the base allow routing the cable from beneath the mount. Attach the unit to the bracket by first connecting the power/transducer cable. Then, hold the sonar unit vertically and slide it onto the bracket from above. (The back of the unit should be touching the front of the bracket as you lower it into [...]

27 Adjust viewing angle: use one hand to press and release the spring- loaded ratchets while you move the unit with the other hand. An op- tional GBSA-3 swivel base is shown with the quick release bracket. Portable Sonar Installation Like many Lowrance products, the M68 sonar is capable of portable operation. It uses the optional PPP-12 portable po[...]

28 NOTE: When the unit is not in use, we recommend you unplug the power connector to reduce the possibility of corrosion or battery drain. When you store the unit, always remove the batteries because dead batteries can leak and corrode the contacts. After installing the batteries, plug the cable's power connector into the socket on the battery[...]

29 If the batteries do lose a charge, you can sometimes restore them by placing them in a warm room or car interior. A better way is to replace them with batteries that have been kept warm. WARNING: Never heat the batteries over an open flame or direct hot air onto them. A fire or explosion could result. Portable Transducer Assembly Recommended too[...]

30 Portable transducer installed on boat transom. NOTE: For optimum operation, the portable transducer should be adjusted so that it is parallel to the ground. For more information on this, see the earlier segment on Transducer Orientation and Fish Arches. Now that you have your unit installed, move on to Sec. 3, Basic Sonar Operations . There, we&[...]

31 Section 3: Basic Sonar Operation KEYBOARD BASICS The unit sounds a tone when you press any key. This tells you the unit has accepted a command. Numbers in the photo correspond to key ex- planations below: Lowrance M68 Sonar, front view, showing screen and keyboard. (A close-up of the keyboard can be found at the beginning of Sec. 7) 1. PWR/LIGHT[...]

32 4. ARROW KEYS – These keys are used to navigate through the menus, make menu selections, move the plotter cursor and sonar chart cursor and enter data. 5. ENT (Enter) – This key allows you to save data, accept values or execute menu commands. It is also used to create event marker icons. 6. EXIT – The Exit key lets you return to the previo[...]

33 Main Menu. The Main Menu commands and their functions are: Screen command: changes the contrast or brightness of the display screen. Sounds command: enables or disables the sounds for key strokes and alarms and sets the alarm style. Alarms command: turns GPS alarms on or off and changes alarm thresholds. Route Planning command: used to plan, vie[...]

34 options. You access the Sonar Menu by pressing the MENU key one time. You run a command by using ↑ or ↓ to highlight the command and then pressing ENT . To clear the menu screen and return to the Page display, press EXIT . Sonar Page Menu. Most of these functions are discussed in Sec. 4, Advanced Sonar Operation . Sonar Menu Commands The Son[...]

35 • Overlay Data command: chooses what types of information (such as water temperature) to show overlaid on the sonar chart screen. • Sonar Features command: launches the Sonar Features menu which controls many functions and options, including screen color mode, auto depth and sensitivity, surface clarity, noise rejection, Fish I.D.  sym- b[...]

36 Sonar chart display options (from left) full sonar chart and split zoom. Sonar chart display options (from left) digital data and flasher. You can customize how the Sonar Page pictures and other data are dis- played in many ways . We'll discuss all of those features and options in the Advanced Sonar Operation section, but to show you how ea[...]

37 Basic Sonar Quick Reference 1. Mount the transducer and unit. Connect the unit to electric power and the transducer. 2. Launch your boat. 3. To turn on the unit, press and release PWR key. 4. Head for your fishing grounds. Your unit automatically displays digi- tal depth and surface water temperature in the corner of the screen. The auto setting[...]

38 Sonar Operations As you can see from the quick reference on the previous page, basic operation is pretty easy, right out of the box. If you are a sonar novice, try operating the unit with the factory defaults until you get a feel for how it's working. As you're learning the basics, there is one setting you might want to tinker with fro[...]

39 You can change the sensitivity level whether you are in Auto Sensitiv- ity mode or Manual Sensitivity mode. The adjustment method works the same in both modes, but it gives you slightly different results. Adjusting sensitivity in Auto Sensitivity Mode is similar to manually ad- justing a car's speed with the accelerator pedal while cruise c[...]

40 NOTE: If you want to change the sensitivity in Manual Mode, first turn off Auto Sensitivity: from the Sonar Page, press MENU | ↓ to A UTO S ENSITIVITY | ENT | ↑ to S ENSITIVITY | ENT . Press ↓ or ↑ to pick a different sensitivity setting. When it's set at the desired level, press EXIT . Important Tip: While you are experimenting and[...]

41 Other Free Training Aids The following section discusses Fish I.D., fish alarms and other fea- tures in greater detail. If you or a friend has Internet access, you can also learn more about interpreting what you see on your sonar screen. Visit our web site, WWW.LOWRANCE.COM . Be sure to check out the free Sonar Tutorial, which includes animated [...]

42 Notes[...]

43 Section 4: Sonar Options & Other Features Material in this section is arranged in alphabetical order. ASP  (Advanced Signal Processing) The ASP  feature is a noise rejection system built into the sonar unit that constantly evaluates the effects of boat speed, water conditions and interference. This automatic feature gives you the best [...]

44 3. Press ↓ or ↑ to select a setting, then press ENT . 4. To return to the previous page, press EXIT | EXIT . Alarms This unit has three different types of sonar alarms. The first is a Fish Alarm. It sounds when the Fish I.D.  feature determines that an echo is a fish. Another alarm is the Zone Alarm, which consists of a bar on the side of[...]

45 3. Press ↑ or ↓ until the depth is correct, then press ENT . 4. Press ← to S HALLOW A LARM E NABLED | ENT | EXIT . 5. To turn off the alarm, press MENU | MENU | ↓ to A LARMS | ENT | ↓ to S ONAR A LARMS | ENT | ENT | EXIT . To switch to a different depth setting, open the Sonar Alarms menu and repeat the instructions in step 3 above. To[...]

46 3. To set the upper boundary for the Zone Alarm, use ← or → to select U PPER , then press ↑ or ↓ to move the top of the bar to the desired depth. 4. To set the lower boundary for the Zone Alarm, use ← or → to select L OWER , then press ↑ or ↓ to move the bottom of the bar to the desired depth. 5. Press EXIT | ← to Z ONE A LARM [...]

47 Chart Speed The rate that echoes scroll across the screen is called the chart speed. The default is maximum; we recommend that you leave the speed set there for virtually all fishing conditions. However, you might consider experimenting with chart speed when you are stationary or drifting very slowly. You may sometimes achieve bet- ter images as[...]

48 they show up mostly as blue arches. A hard bottom or other relatively hard target returns a strong signal which causes a wider brightly col- ored line (reddish yellow to bright yellow.) If you have two signals of equal size, one with red to yellow color and the other without, then the target with brighter color (yellow) is the stronger signal. T[...]

49 Depth Cursor The depth cursor consists of a horizontal line with a digital depth box on the right side. The numbers inside the box show the depth of the cursor. At left, Sonar Page menu with Depth Cursor command selected. At right, sonar chart with the depth cursor active. The line indicates the large fish is 15.77 feet deep. The cursor can be m[...]

50 At left, Sonar Page menu with Depth Range command selected. At right, the Depth Range Control Scale. 2. The Depth Range Control Scale appears. Press ↑ or ↓ to select a dif- ferent depth range. A dark bar highlights the selected range. Range numbers in gray cannot be selected. 3. When the new range is selected, press EXIT to clear the menu. D[...]

51 Changing the upper and lower limits gives you far greater control over the depth range. This feature lets you "zoom in" the display in almost unlimited combinations. Nearly any segment of the water column, from the surface to the bottom can be shown. This enlarges the sonar targets to best suit your fishing needs and water conditions. [...]

52 To turn off upper and lower limits: 1. From the Sonar Page, press MENU | ↓ to A UTO D EPTH R ANGE | ENT | EXIT . FasTrack  This feature automatically converts all echoes to short horizontal lines on the display's far right side. The graph on the rest of the screen con- tinues to operate normally. FasTrack gives you a rapid update of co[...]

53 You may see fish symbols on the screen when actually, there are no fish. The reverse is also true. Does that mean Fish I.D. is broken? No — the feature is simply inter- preting sonar returns in a specific way to help take some of the work out of reading the screen. Remember: Fish I.D. is one of the many tools we provide so you can analyze your[...]

54 Sonar Features menu with Fish I.D. Depths selected. When the che ck box to t he l eft is c hec ked , th e fe atu re i s on . At right, Sonar Page show- ing Fish I.D. symbols and FishTrack depths turned on. HyperScroll  See the entry on Ping Speed, which controls the HyperScroll feature. Noise Rejection See the entry on Advanced Signal Process[...]

55 Data list showing "Ground Speed" turned on to display on Sonar Page. 3. To return to the previous page, press EXIT | EXIT . To turn off displayed data: 1. Press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ or ↑ to select Data Type, then press ENT until the check mark to the left of the selected data type disappears. (If you wish[...]

56 Ping Speed & HyperScroll  Ping Speed controls the rate at which the transmitter and transducer broadcast sonar sound waves — pings — into the water. The unit has a default ping speed of 50 percent. At normal boating speeds, this auto- matically provides enough return echoes to refresh the screen and scroll the chart at maximum chart s[...]

57 To adjust Sensitivity: 1. From the Sonar Page, press MENU | ENT . 2. The Sensitivity Control Bar appears. Press ↓ to decrease sensitivity; press ↑ to increase sensitivity. When it's set at the desired level, press EXIT . (When you reach the maximum or minimum limit, a tone sounds.) To turn off HyperScroll: 1. From the Sonar Page, press [...]

58 Sensitivity & Auto Sensitivity The sensitivity controls the ability of the unit to pick up echoes. Sensi- tivity can be adjusted, because water conditions vary greatly. A low sensitivity level (from zero to 50 percent) excludes much of the bottom information, fish signals, and other target information. Boosting sensitivity will show more inf[...]

59 At left, Sonar Menu with Sensitivity command selected. At right, the Sensitivity Control Bar. To adjust sensitivity in manual mode: 1. First, turn off Auto Sensitivity: from the Sonar Page, press MENU | ↓ to A UTO S ENSITIVITY | ENT . 2. Press ↑ to S ENSITIVITY | ENT and the Sensitivity Control Bar appears. Press ↓ or ↑ to pick a differe[...]

60 On sailboats or other large vessels with deep drafts, the distance be- tween the transducer installation and the keel or lower engine unit can be several feet. In those cases, an inexact depth reading could result in grounding or striking underwater structure. The Keel Offset feature eliminates the need for the navigator to mentally calculate ho[...]

61 2. Press ↓ to S ONAR C HART M ODE | ENT . 3. Press ↓ or ↑ to Mode Name | ENT . 4. Press EXIT | EXIT to return to the Sonar Page. Sonar Page & Sonar Chart Display Options The M68 offers four Sonar chart display options. To choose among them, press EXIT to clear any menus, then press PAGES and use the ar- row keys to select the desired m[...]

62 Split Zoom Sonar Chart. Image at left shows the left window zoomed to 2X. The right image shows the left window zoomed to 4X. The depth overlay data is set to the default large text size; the water temperature is set to the medium text size. Digital Data/Chart This mode shows seven digital data boxes or windows containing (by de- fault): Water D[...]

63 Flasher page. Sonar Simulator This unit has a built-in simulator that lets you run it as if you were on the water. All sonar features and functions are useable. When in simulator mode, you will see [Simulator Mode] in the Sonar Page title bar. To use the simulator: 1. From the Sonar Page, press MENU | MENU | ↓ to S ONAR S ETUP | ↓ to S ONAR [...]

64 To turn on sonar and start the chart scrolling again, repeat the above step. Sonar Menu with Stop Chart command selected. The box is unchecked, indicating that the chart is scrolling across the screen. Surface Clarity The markings extending downward from the zero line on the chart are called "surface clutter." These markings are caused[...]

65 2. Press ↓ or ↑ to select clarity level | EXIT | EXIT | EXIT . Upper and Lower Limits See the entry in this section for Depth Range - Upper and Lower Limits Zoom & Zoom Bar "Zooming" the display is used to enlarge small detail, fish signals and the bottom with its associated structure. The 2X zoom doubles the size of all echoes[...]

66 lets you rapidly move the zoomed area up and down to different depths. By "pointing" your zoom at different portions of the chart as it scrolls, you can get a good, close-up look at structure or cover below you. To use Zoom Pan, switch to a manual depth Range setting (see page 50) and turn on 2X or 4X Zoom. Then, simply press ↑ or ?[...]

67 Section 5: Ice Fishing The M68C and the M68C IceMachine  work exactly alike. Each M68C unit contains a menu command that allows you to switch the sonar in and out of IceMachine mode. The only differences between the two pack- ages are the accessories they are shipped with. The IceMachine  package includes the M68C sonar unit and the PPP-15[...]

68 there is the Ice Flasher. This page is only visible in IceMachine Mode. You can tell at a glance which mode you are in because the battery gauge only appears in the lower right corner of the Ice Flasher page. Ice Flasher page, left, and normal Flasher page, right. The ice mode differs from normal mode in two ways. First, the unit changes how it [...]

69 At left, M68C IceMachine opening screen, showing the Full Sonar Chart Page. The Backlight Level control bar automatically disappears after five seconds. At right, the Full Sonar Chart is shown. To enter the IceMachine mode: 1. From the Full Chart Sonar page, press ENT | ENT | ENT to switch to the normal Flasher page. 2. Press MENU | ↓ to I CE [...]

70 The following figure shows the various components of the Ice Flasher page display. Ice Flasher page. Temp display requires optional TS-2U temp sensor. Sensitivity Sensitivity and Auto Sensitivity are described in detail in Sec. 4. To ad- just sensitivity on the Flasher or Ice Flasher page, simply press ↑ to in- crease sensitivity and press ↓[...]

71 To adjust sensitivity: 1. Start with your IceMachine showing the Ice Flasher page, in the de- fault IceView color mode. 2. Drop your lure five to 10 feet directly below the transducer. You should be able to follow the fall of the bait on the flasher screen. 2. Use the arrow keys to turn the sensitivity up or down until the lure is barely visible[...]

72 In the Ice Flasher, the weakest signals are shown in black and the strongest signals show as red. Fish are among the weakest echoes, so they show up mostly as black and blue bands on the flasher screen. The hardest surfaces, like the bottom, show as red. Cover in the form of weed beds or submerged timber display in the blue to yellow range. Batt[...]

73 Red signals are much larger fish, or fish that are in the center of the sonar cone, almost directly below the transducer. They return the strongest echoes. Signals that are yellow and some other color result from mid-sized fish that are in a transition zone between the center and outer edges of the sonar cone. They represent medium-strong echoes[...]

74 At left, Flasher Page Menu with Flasher Options command high- lighted. Center, Flasher Options Menu with Flasher Display Mode se- lected. At right, the Split Zoom option has been selected. The following figure show the bottom target separation possible using the flasher's Split Zoom. Notice the bottom target separation with Split Zoom mode.[...]

75 There are six color mode options for the flasher pages, and seven for the sonar chart page. The Ice Flasher default color is the IceView mode, but other settings may suit your eyes better. For example, some of our fishing friends favor the striking green-on- black contrast of the Nightview mode…they use it a lot, even in broad daylight! Experi[...]

76 Another variation used by some anglers requires a small plastic bag, such as a food storage bag. They fill the bag with a mixture of RV anti- freeze and water. The bag is placed on the ice surface, and the trans- ducer is rested in the "puddle" just as your head rests on a pillow.[...]

77 Section 6: Sonar Troubleshooting If your unit is not working, or if you need technical help, please use the following troubleshooting section before contacting the factory customer service department. It may save you the trouble of returning your unit for repair. For contact information, refer to the last page, just inside the back cover of this[...]

78 3. The water may be deeper than the sonar's ability to find the bottom. If the sonar can't find the bottom signal while it's in the automatic mode, the digital sonar display will flash continuously. It may change the range to limits far greater than the water you are in. If this hap- pens, place the unit in the manual mode, then c[...]

79 To eliminate or minimize the effects of electrical noise, first try to de- termine the cause. With the boat at rest in the water, the first thing you should do is turn all electrical equipment on the boat off. Make sure the engine is also off. Turn your sonar on, then turn off Noise Reject [also known as the ASP feature (Advanced Signal Processi[...]

80 Notes[...]

81 Section 7: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 7 follow a chronological order. Sec. 8, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 8 is arranged in alphabetical order. Before you turn on the M68 and find[...]

82 4. ARROW KEYS – These keys are used to navigate through the menus, make menu selections, move the map cursor and sonar chart cursor and enter data. 5. ENT (Enter) – This key allows you to save data, accept values or execute menu commands. It is also used to create event marker icons. 6. EXIT – The Exit key lets you return to the previous s[...]

83 You can access the Main Menu from any of the display options by pressing MENU | MENU . To clear the menu screen and return to the page display, press EXIT . Main Menu. The Main Menu commands and their functions are: Screen command: changes the contrast or brightness of the display screen. Sounds command: enables or disables the sounds for key st[...]

84 Pages The unit has two Pages that represent the two major operating modes. They are the Map Page and the Sonar Page. Each Page has several sub- set display options. They are accessed by pressing the PAGES key, then using → or ← to select a Page, then ↑ or ↓ to select a display option. (Clear the Pages Menu by pressing EXIT .) Pages Menu,[...]

85 Satellite Page. Left view indicates unit has not locked on to any satel- lites and does not have a fix on its position. Center view shows satel- lites being scanned. Right view shows satellite lock-on with a 3D posi- tion acquired (latitude, longitude and altitude.) This screen shows a graphical view of the satellites that are in view. Each sate[...]

86 Navigation Page This screen has a compass rose that not only shows your direction of travel, but also the direction to a selected waypoint. To get to the Navi- gation Page: Pre ss PAGES | ← to M AP | ↑ or ↓ to N AVIGATION | EXIT . The navigation screen looks like the one below when you're not navi- gating to a waypoint or following a [...]

87 Speed (ground speed) is the velocity you are making over the ground. (If you wish, you can customize the Speed window to display Closing Speed instead. Closing Speed is also known as velocity made good. It's the speed that you're making toward the waypoint. For instructions, see the Customize Page Displays entry in Sec. 9.) Navigation [...]

88 A circular symbol depicting your destination (waypoint) appears on the screen as you approach the waypoint, as shown on the screen in the previous figure. Travel Time is the time that it will take to reach your destination at your present closing speed. (You can also customize the time window to show Arrival Time instead. Arrival Time is the loc[...]

89 Far left, Map Page opening screen. Center, zoomed to 100 miles and right, zoomed to 15 miles. The maximum zoom range for showing additional map detail is 20 miles. You can continue to zoom in closer, but the map will simply be enlarged without revealing more map content (except for a few major city streets). The background map includes: low-deta[...]

90 Pages Menu with Map With Sonar option selected, left. Map With Sonar display, at right. The left map is active. Resize Window is another extremely handy feature for pages that have two major windows. You can change the horizontal size of the windows to suit your viewing preference. Here's how: 1. From any two-window display, press MENU | ?[...]

91 GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navigating to a location at least a few blocks away. While you're learning, navigation in too small an area will constantly trigger arrival alarms. 1. Install the unit. (See complete installation details beginning on page 9.) 2. To turn on the M68, p[...]

92 Find Your Current Position Finding your current position is as simple as turning the unit on. Un- der clear sky conditions, the unit automatically searches for satellites and calculates its position in approximately one minute or less. NOTE: "Clear sky" means open sky, unobstructed by terrain, dense foliage or structures. Clouds do not[...]

93 The selected wreck (the Empress) to the southeast is 12.81 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob- ject. On most items, a pop-up box will give the name of the se[...]

94 Sequence for setting a waypoint. Step 1: while traveling, quickly press WPT twice to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: ve- hicle continues on its way; number waypoint symbol is visible on map. NOTE: The Quick Save method uses the default waypoint symbol unti[...]

95 2. Press WPT | WPT . The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 001." The waypoint symbol and number appear on the map. Create Waypoint by Entering a Position 1. Press WPT | → to N EW | ENT . 2. Press ↓ to E NTERED P OSITION | ENT | ↑ to C REATE | ENT . 3. Press ↓ to L ATITU[...]

96 Navigation Page, navigating toward waypoint 2 and leaving a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. This situation can be deadly on any body of wa- ter — fresh or salt. It's particularly dangerous at night or if you're out of sight of lan[...]

97 Navigating to Man Overboard: "Man Overboard activated" message shown at left. The Navigation Page is shown in the center and Map Page is shown at right. The victim is astern of the vessel; the GPS shows which direction to steer to for the rescue. The man overboard position is also stored in the waypoint list for future reference. It ca[...]

98 Navigate to cursor. In this example, the cursor has selected the town of Oologah, Oklahoma. 3. Press MENU | ENT and the M68 will begin navigating to the cursor location. The Map Page will display a red line from your current position to the cur- sor position. The Navigation Page displays a compass rose showing naviga- tion information to your de[...]

99 Navigate to a Map Place For map places that are in view on the map, you can easily use the Navigate to Cursor command above; just use the cursor to select the map place. The other method involves searching for map places with the Find Waypoint command, launched with the WPT key. Turn to Sec. 10, Searching , for detailed instructions on map place[...]

100 Sequence for saving a trail and beginning a new one. At left, My Trails command. Center, the Trails Menu. The arrow to the right of Trail 3 indicates the trail is "active," and the check to the left indicates the trail is visible on the map display. The right figure shows the Edit Trail menu, with the Active command selected. 2. Press[...]

101 You can save and recall up to 10 different plot trails. Tip: Another quick way to stop recording one trail and begin a new one is to use the New Trail command: Press MENU | MENU | ↓ to M Y T RAILS | ENT | ENT | EXIT | EXIT | EXIT . Caution: You also have the option of completely turning off trail record- ing, under the trail Options command. [...]

102 The other two methods provide a full range of navigation data and work with both the Map Page and Navigation Page. The only difference be- tween them is "navigating a trail" follows a trail forward (from start to end) while "backtracking" follows a trail in reverse (from end to start.) When hiking at walking speed with a han[...]

103 Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate Route command highlighted for Trail 1. A trail is always con- verted to a "route" when you navigate the trail. On the Map Page, the trail you are navigating is represented by a flashing magenta[...]

104 Navigate trail, map views: at left driver is heading southeast straight toward trail point 3. At right, driver has reached point 3 and has turned southwest to follow the trail. Navigate trail, navigation page (compass rose) views: at left, driver is heading northeast straight toward trail point 3; bearing arrow shows the trail point is 61 degre[...]

105 4. Press → to R EVERSE R OUTE | ENT | ← to N AVIGATE R OUTE | ENT . The unit begins showing navigation information along the trail, in reverse. NOTE: If you are already located at or near the end of your trail, the arri- val alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and [...]

106 Notes[...]

107 Section 8: Advanced GPS Operations Find Distance From Current Position To Another Location 1. While on the Map Page press: MENU | ↓ to F IND D ISTANCE | ENT . 2. Center your cursor over the position you want to find the distance to. A rubber band line appears, connecting your current position to the cursor's location. The distance along [...]

108 called later for navigation purposes. These are sometimes referred to as event marker icons. The M68 has 42 different symbols you can pick from when creating an icon. Icons are similar to waypoints, but they do not store as much informa- tion (like names) as waypoints do. You can't use a menu to navigate to icons as you can with waypoints.[...]

109 2. Press ↓ to D ELETE A LL I CONS , D ELETE B Y S YMBOL , or D ELETE F ROM M AP and press ENT . Delete icons menu. The Delete All Icons command will ask if you are sure. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol menu. Press ← or ↑ or → or ↓ to select th[...]

110 waypoint. Once programmed into the GPS unit, a route provides the option of navigating forward through the route waypoints or in reverse order (you can even begin navigating in the middle of a route!) Create and Save a Route You can create a route by selecting existing waypoints from the way- point list or you can set a series of route waypoint[...]

111 (If you are starting at your current position or the current cursor posi- tion, you are already at the starting spot.) 4. Set the first route waypoint: press ENT . In this example, we moved to the entrance of the cove where our boat was docked to start our route to a promising fishing spot next to an oil platform. (Creating this example route i[...]

112 5. Move the cursor to the next point in the route, a spot where you need to turn or change direction, and press ENT to set the next waypoint. 6. Repeat step five until the route reaches your destination. 7. To save your route, press EXIT . The M68 reverts to the Edit Route screen, with the route automatically named "Route 1" and store[...]

113 Edit Route Waypoints menu. 3. Use ↓ and ↑ to select a command from the Edit Route Waypoints menu and press ENT . Add From Map lets you insert a waypoint in the route by clicking on a map location with the cursor. Add Waypoint calls up the Waypoint List so you can insert a waypoint from the list. Re- move Waypoint will delete the selected wa[...]

114 The following figures show what the Navigation Page and Map Page look like while navigating a route. Navigating along a route: Fig. 1 shows the Navigation Page at the start of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived at Wpt 1; the arrival alarm has been triggered and the bearing arrow on the [...]

115 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE , press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Press ↓ to select route name | ENT | → to R EVERSE | ENT | ← to N AVIGATE R OUTE | ENT . 3. Upon arrival at your destination, cancel navigation: press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES[...]

116 Edit a Trail Color To edit a trail color: press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | ↓ to C OLOR | ENT . Press ↑ or ↓ to select a color style, then press ENT . Press EXIT | EXIT | EXIT | EXIT to return to the previous page display. Edit a Trail Pattern To edit a trail pattern: press MENU | MENU | ↓ to M Y T[...]

117 Trip Up Timer To get to the Up Timer menu: press MENU | MENU | ↓ to T IMERS | ENT | ENT . Waypoints Delete a Waypoint To delete a waypoint from the waypoint list: press WPT | ENT | ENT | ENT | ↓ to waypoint name | ENT | → to D ELETE W AY- POINT | ENT | ← to Y ES | ENT . To return to the previous page, press EXIT | EXIT . To delete a way[...]

118 Selecting a Waypoint To select a waypoint on the map (for navigating to, for editing, etc.,) use the arrow keys and center the cursor over the waypoint. A highlighted halo will appear around the waypoint. Set a Waypoint by Average Position This feature sets a waypoint at the current position after taking several position readings and averaging [...]

119 Section 9: System & GPS Setup Options Alarms This unit has several GPS alarms. The factory default setting has all the alarms turned on. You can turn the alarms off and on and change their distance settings. You can set an arrival alarm to flash a warning message and sound a tone when you cross a preset distance from a waypoint. For example[...]

120 to change the first character, then press → to the next character and repeat until the distance is correct. 4. When your adjustments are finished, return to the last page dis- played by repeatedly pressing EXIT . Auto Satellite Search To lock onto the satellites, the GPS receiver needs to know its current position, UTC time and date. (Elevati[...]

121 You can force the unit to immediately kick into auto search mode. Here's how: 1. Press PAGES | ← to M AP | ↓ to S ATELLITES . 2. Press MENU | ↓ to GPS A UTO S EARCH | ENT | ← to Y ES | ENT . Coordinate System Selection The Coordinate System Menu lets you select the coordinate system to use when displaying and entering position coor[...]

122 on this unit. Your position and datum in use determines which one to use. If you use standard, and your position is off significantly, then try the alternate. NOTE: When the position format is changed, it affects the way all posi- tions are shown on all screens. This includes waypoints. To change the coordinate system, press ENT while C OORDINA[...]

123 tude/longitude lines must be parallel with the edge of the map. USGS maps are parallel, others may not be. Also, this works better with smaller scale maps.) The reference position can be anywhere on the map, but the closer it is to your location, the smaller the numbers will be that you'll have to deal with. Once you've decided on a r[...]

124 Customize Page Displays The Full Map, Navigation and Position pages can all be customized to display many different types of navigation information in data boxes. Pages can be customized by turning data boxes on or off. These data boxes (sometimes referred to as text boxes, data windows or information displays) are controlled with the Customize[...]

125 ner begins flashing. Use the arrow keys to select the box you want to change. With the display box highlighted and flashing, press ENT to open a list of options. Scroll ↑ and ↓ to select a different data option, then press ENT . You can repeat these steps to change the display in another box. When all the changes are finished, press EXIT to[...]

126 above steps or turn the unit off. While in simulator mode, you can press EXIT to clear the steering and speed boxes from the screen while continuing the simulation. This will allow you to use the map cursor during a simulation. . To turn steering and speed boxes back on again, return to the GPS Simulator menu, se- lect the S TEER WITH A RROWS c[...]

127 map in the location you selected with the cursor. The unit will consider that spot as its last known position until changed by either a live satel- lite lock-on or a new simulator location. Map Auto Zoom This receiver has an auto zoom feature that eliminates much of the but- ton pushing that other brands of GPS receivers force you to make. It w[...]

128 Pop-up Map Info From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Press ↓ to P OPUP M AP I NFORMATION . With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT | EXIT to return to the page display. Fill Water With White From the Map Page, press MENU | ↓ to M AP D AT[...]

129 All datums are named. The GPS system is based on the WGS-84 da- tum, which covers the entire world. Other datums may also cover the entire world, or just a small portion of it. By default, your position shows using the WGS-84 datum. However, it can show your position using one of 191 different datums. Different datums can be selected; to change[...]

130 Map Menu, left, Map Categories Drawn Menu, right. Map Orientation By default, this receiver shows the map with north always at the top of the screen. This is the way most maps and charts are printed on paper. Map orientation at left is shown in north up and at right, track up. This is fine if you're always traveling due north. What you see[...]

131 To change map orientation: from the Map Page, press MENU | ↓ to M AP O RIENTATION | ENT . Use ↑ or ↓ to select the desired mode, then press ENT . Press EXIT | EXIT to return to the page display. Map Menu, left; Map Orientation menu with the North Up map orientation option selected, right. Overlay Data The Sonar Page and the Map Page can b[...]

132 To change the digital data shown on top of the Sonar Page or the Map Page: First, press PAGES , use → or ← to select a Page Name , then press EXIT . To select data for display: 1. From the Map or Sonar page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ or ↑ to select Data Type | ENT . Overlay Data command on the GPS Menu, at le[...]

133 3. To return to the previous page, press EXIT | EXIT . To change displayed data font size: 1. From the Map or Sonar page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ or ↑ to select Data Type |press → or ← to Data Size | EXIT | EXIT . The selected data type will be displayed in the new size. (To change the font size for more th[...]

134 Reset Options To reset all features to their factory defaults: Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to R ESET O PTIONS | ENT | ← to Y ES | ENT . NOTE: Reset Options does not erase any waypoints, routes, icons, plot trails or sonar logs. System Menu with Reset Options command selected. Screen Contrast and Brightness To access [...]

135 To adjust the display's brightness: Press ↓ to B RIGHTNESS . Press → or ← to move the bar. The left end of the scale is minimum contrast; the right end is maximum contrast. To adjust the screen's display mode: Press ↓ to D ISPLAY M ODE | ENT |press ↑ or ↓ to select mode | EXIT . Display Mode menu. Set Language This unit&ap[...]

136 To set the Month: Press ↓ to M ONTH | ENT . Press ↑ or ↓ to select the month, then press ENT . To set the Day: Press → to D AY | ENT . Press ↑ or ↓ to select the day, then press ENT . To set the Year: Press → to Y EAR | ENT . Press ↑ or ↓ to select the year, then press ENT . The last field in this menu is C ONFIG DST . This fe[...]

137 At left, Main Menu with Software Information command selected. At right, the Software Information screen. 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to S OFTWARE I NFO | ENT . 2. Read the information displayed on the screen. 3. To return to the last page displayed, press EXIT | EXIT | EXIT . Sounds and Alarm Sound Styles Sounds tr[...]

138 To set Alarm Sounds: Press ↓ to A LARM S OUNDS . With the option high- lighted, press ENT to check it (turn on) and uncheck it (turn off). After the option is set, press EXIT | EXIT to return to the page display. To set Alarm Volume: Press ↓ to V OLUME . Press → or ← to move the bar. The left end of the scale is low volume; the right en[...]

139 Main Menu, left, Trails Menu, center, Trail Options, right. Delete All Trails To remove all of the trails from memory: from the Trails Menu, press → to D ELETE A LL | ENT | ← to Y ES | ENT . Update Active Trail Option This menu lets you change the way the trail updates occur. WARNING: If you uncheck the Update Trail option, automatic trail [...]

140 With one of the Update Criteria selected, use the cursor arrows to highlight either the U PDATE R ATE or U PDATE D ISTANCE data entry boxes and press ENT . Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the entry is correct. Press EXIT to return to the Trail Options Menu. Trail Options menu[...]

141 Trail Visible/Invisible and Other Trail Options The name, maximum number of points in the trail, activity, and visi- bility are all changed on the Edit Trail menu screen. The Active setting determines whether or not the unit is recording new points for a par- ticular trail. On the Edit Trail menu, press ↓ or ↑ to highlight the section you w[...]

142 Units of Measure This menu sets the speed and distance (statute or nautical miles, me- ters), depth (feet, fathoms, or meters), temperature (degrees Fahrenheit or Celsius) and heading (true or magnetic) units. To change the units: Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ENT . Main Menu, left, Units of Measure Menu, right. To set Units[...]

143 Section 10: Searching NOTE: The background map loaded in your unit lets you search for high- ways and arterial streets in the U.S., as well as land features, in- cluding cities and lakes. For a complete description of what detail is found in the background map, see page 89. The unit's search functions all begin with either the Find Waypoin[...]

144 A Map Place selected by the cursor, left, Waypoint Information screen, right. NOTE: Since the Go To command is highlighted, you can navigate to the selected map place by pressing ENT | EXIT while in the Waypoint In- formation screen. Find Map Places 1. Press WPT , press ↑ or ↓ to select a map place category, then press ENT . You will be giv[...]

145 Find by Nearest option, left, Calculating screen, center, map places list, right. 3. Search by name. Press ↓ | ENT . There are two options: A. You can spell out the map place in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then pr[...]

146 Go To Waypoint option, left; Find on Map option, right. Find Streets or Intersections Find a Street 1. From the Map Page, press MENU | ↓ to F IND S TREETS | ENT and the Find Streets Menu appears. Find Streets command, left, Find Streets menu, right. 2. You must fill in a street name in the First Street dialog box. Press ENT to display the Fin[...]

147 Find Street By Name menu. Spell out name in the top box, or select from the list in the lower box. 3. The Find Streets menu reappears with the street you're searching for in the First Street box. (In this example, it's I-35.) To search for that street, press ↓ to F IND F IRST S TREET | ENT . A message appears asking you to wait whil[...]

148 Map Page showing results of a street search. The cursor points to the located street. If you want to navigate to the found street at the cursor location, just press MENU | ENT | EXIT . Find an Intersection You must enter one street in the First Street dialog box and enter the next street in the Second Street dialog box. 1. From the Map Page, pr[...]

149 dialog boxes filled in. In this example, we selected I-44 as our second street. You could now use similar techniques to select a city or Zip code, but your search will probably be faster if you leave those boxes blank. (You can specify a city and/or Zip code later on to narrow the search, if the resulting list is too long.) Find Intersection co[...]

150 If you want to navigate to the found intersection, just press MENU | ENT | EXIT . Find Waypoints 1. Press WPT | ENT . 2. If searching for the Nearest waypoint, press ENT . If searching for the waypoint By Name , press ↓ to N EAREST | ENT . (To search by name, jump to step 5 below.) Find Waypoint menu, left; Find By Name command, center, Find [...]

151 wanted to, you could select another waypoint form the list with the ↑ or ↓ keys.) A. To navigate to the waypoint, press ENT . (The Go To Waypoint command is already highlighted.) The unit will show navigation in- formation to the waypoint. B. To find the waypoint, press → to F IND O N M AP | ENT . The Map Page appears with the cursor high[...]

152 Find By Name menu, left. Waypoint Information screen, center. At right, the found waypoint is highlighted by the cursor on the Map Page. A. To navigate to the waypoint, press ENT . (The Go To Waypoint command is already highlighted.) The unit will show navigation in- formation to the waypoint. B. To find the waypoint, press → to F IND O N M A[...]

153 Section 11: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adindan Sudan Afgooye Somalia Ain el Abd 1970 Bahrain Ain el Abd 1970 Saudi Arabia Anna 1 Astro 1965 Cocos Islands Antigua Island Astro 1943; Antigua (Le[...]

154 Chua Astro Paraguay Corrego Alegre Brazil Dabola Guinea Djakarta (Batavia) Indonesia (Sumatra) DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gi- braltar, Greece, Italy, Luxembourg, Neth- erlands, Norway, Portugal, Spain, Sweden, Switze[...]

155 Naparima BWI Trinidad & Tobago North American 1927 Mean for Antigua, Barbados, Barbuda, Caicos Islands, Cuba, Dominican Republic, Grand Cayman, Jamaica, Turks Islands North American 1927 Mean for Belize, Costa Rica, El Sal- vador, Guatemala, Honduras, Nicaragua North American 1927 Mean for Canada North American 1927 Mean for CONUS (Continen[...]

156 Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS 85 Soviet Geodetic System 1985 South American 1969 Mean for Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Trinidad &a[...]

157 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful in- terference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired opera- tion. Chan[...]

158 Notes[...]

159 Index A Accessories, 1, 5, 23, 24, 67 Sec. 2, Installation & Accessories , 9 Alarm Clock, 116 Alarms, 33, 44, 45, 46, 83, 91, 102, 103, 105, 114, 119, 126 Anchor Alarm, 119 Antenna, 4, 5, 79, 92, 157 Arrival Alarm, 91, 102, 103, 105, 114, 119, 126 B Backlights / Lighting, 3, 31, 68, 69 Batteries, 9, 22, 23, 27, 28, 29, 32, 67, 68, 72, 77, 7[...]

160 124, 132 Map Page, 30, 84, 87, 88, 89, 95, 96, 97, 98, 101, 102, 103, 107, 109, 110, 112, 113, 114, 115, 124, 125, 126, 127, 128, 129, 131, 132, 143, 146, 147, 148, 149, 151, 152 Navigation Page, 86, 87, 88, 91, 96, 97, 98, 102, 103, 109, 110, 112, 113, 114, 115, 124 Plotter Page, 8, 32 Position Page, 103, 124 Satellite Status Page, 84, 85, 91 [...]

161 Notes[...]

162 Notes[...]

163 LOWRANCE DATABASES LICENSE AGREEMENT THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS, INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US"). USING THE PRODUCT ACCOMPANIED BY T[...]

164 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer of this product. "You" or "your" refers to the first person who purchases the prod- uct as a consumer item for personal, family, or household use. The Databases Limited Warranty applies to the [...]

165 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use. We warrant this product against[...]

166 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Lowrance parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any product can be returned, you must call customer serv[...]

Accessory Ordering Information for all countries To order Lowrance accessories such as power cables or transducers, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items. To locate a Lowrance [...]

Visit our web site: Lowrance Pub. 988-0152-031 © Copyright 2003 All Rights Reserved Printed in USA 102203 Lowrance Electronics, Inc.[...]