Lowrance electronic X105C DF manuel d'utilisation

Pub. 988-0156-001 www.lowrance.com X100C & X105C DF Fish-finding & Depth Sounding Sonars Installation and Operation Instructions[...]

Copyright © 2004 Lowrance Electronics, Inc. All rights reserved. Lowrance ® is a registered trademark of Lowrance Electronics, Inc. Lowrance Electronics may find it nece ssary to change or end our policies, regulations, and special offers at an y time. We reserve the right to do so without notice. All features and spec ifications subject to chang[...]

i Table of Contents Sec. 1: Read Me First! ............................................................... 1 Capabilities and Specifications: X100C, X105C DF .................... 2 How Sonar Works ......................................................................... 3 How to Use this Manual: Typographical Conventions................ 4 Sec. 2: I[...]

ii Depth Range - Manual................................................................ 51 Turn Auto Depth Range on Again: ......................................... 51 Depth Range - Upper and Lower Limits ................................... 51 FasTrack  .................................................................................. 53 Fish I.[...]

1 Section 1: Read Me First! How this manual can get you out on the water, fast! Welcome to the exciting world of digital sonar! We know you're anxious to begin finding fish, but we have a favor to ask. Before you grab your unit and begin installing it, please give us a moment or two to explain how our manual can help you get the best performan[...]

2 If you're having difficulty with your sonar, you can find an answer to the most common problems in Section 5, Sonar Troubleshooting . Finally, in Section 6, we offer Supplemental Material , including a list of warranty and customer service information. Now, if you're into the fine details, glance over the next segment on specifications [...]

3 Actual capability depends on transducer configuration and installation, bottom com- position and water conditions. All sonar units typically read deeper in fresh water than in salt water. Depth display: ................ Continuous display . Audible alarms: ............. Deep/shallow/fish/zone. Automatic ranging: ....... Yes, with instant screen u[...]

4 How to use this manual: typographical conventions Many instructions are listed as numbered steps. The keypad and arrow "keystrokes" appear as boldface type. So, if you're in a real hurry (or just need a reminder), you can skim the instructions and pick out what menu command to use by finding the boldface command text. The fol- lowi[...]

5 Section 2: Installation & Accessories Preparations You can install the sonar system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vessel! 1. Determine the approximate location for the sonar unit, so you can plan[...]

6 NOTE: The following installation types also call for these recommended tools and required supplies that you must provide (supplies listed here are not included): Single-frequency transom installations Tools include: two adjustable wrenches, drill, #29 (0.136") drill bit, flat- head screwdriver. Supplies: high quality, marine grade above- or [...]

7 boat hulls have a flat keel pad that offers a good mounting surface. On vee hulls, try to place the transducer where the deadrise is 10 ° or less. Left, vee pad hull; right, vee hull. A pod style transducer is shown here, but the principle is the same for Skimmers inside a hull. 4. If the transducer is mounted on the transom, make sure it doesn&[...]

8 Align transducer centerline with hull bottom. However, there are times when you may need to adjust the transducer slightly higher or lower. (The slots in the mounting brackets allow you to loosen the screws and slide the transducer up or down.) If you fre- quently lose bottom signal lock while running at high speed, the trans- ducer may be coming[...]

9 Lack of angle adjustment can be particularly troublesome on hulls that sit with the bow high when at rest or at slow trolling speeds. Third, a transducer CAN NOT shoot through wood and metal hulls. Those hulls require either a transom mount or a thru-hull installation. Fourth, if your Skimmer transducer has a built in temp sensor, it will only sh[...]

10 Place the ratchets into the bracket with the letter "A" aligned with the alignment mark mold ed int o the b rack et. Pl ace th e rat chets onto t he transducer with the letter "A" aligned with the 12 o'c loc k position on the transducer stem. These positions set the transducer's coarse angle adjustment for a 14 ° t[...]

11 If the transducer's face isn't parallel with the ground, remove the transducer and ratchets from the bracket. Place the ratchets into the holes in the bracket with the letter "B" aligned with the dot stamped in the bracket. Reassemble the transducer and bracket and place them against the transom. Again, check to see if you ca[...]

12 Assemble transducer and bracket. 3. Assembling the transducer. A. One-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the following fig- ure. Don't tighten the lock nut at this time. Assemble transducer and bracket. B. Two-piece bracket: Once you determine the correct position for[...]

13 Position transducer mount on transom and mark mounting holes. Side view shown at left and seen from above at right. 5. Attaching transducer to transom. A. One-piece bracket: Remove the transducer from the bracket and re-assemble it with the cable passing through the bracket over the bolt as shown in the following figures. For single-frequency Sk[...]

14 Align transducer centerline with hull bottom and attach transducer to transom. Rear view of dual-frequency Skimmer shown. 6. Route the transducer cable through or over the transom to the sonar unit. Make sure to leave some slack in the cable at the transducer. If possible, route the transducer cable away from other wiring on the boat. Electrical[...]

15 TROLLING MOTOR BRACKET INSTALLATION (single-frequency only) 1. Attach the optional TMB-S bracket to the transducer as shown in the following figure, using the hardware supplied with the transducer. (Note: The internal tooth washer is supplied with the TMB-S.) Attach motor mounting bracket to transducer. 2. Slide the adjustable strap supplied wit[...]

16 Transducer angles and their effects on fish arches. If the arch slopes up – but not back down – then the front of the trans- ducer is too high and needs to be lowered. If only the back half of the arch is printed, then the nose of the transducer is angled too far down and needs to be raised. NOTE: Periodically wash the transducer's face[...]

17 WARNING: Do not remove any material from your inner hull unless you know the hull's composition. Careless grinding or cutting on your hull can result in damage that could sink your boat. Contact your boat dealer or manufacturer to confirm your hull specifications. Epoxy the transducer to a solid portion of the hull. For example, some (but n[...]

18 To choose the proper location for shoot-thru-hull mounting, follow these testing procedures: (You may need a helper to complete these steps.) 1. Anchor the boat in about 30 feet of water. Add a little water to the sump of the boat. Plug the transducer into the sonar unit, turn it on, then hold the transducer over the side of the boat in the wate[...]

19 4. Most people can get good results by following steps 1 through 3, so this step is optional . If you want to make an extra effort to be absolutely sure that your selected location will work under all conditions, make a test run with the boat on plane and observe the bottom signal. You'll need to figure some way to prop the transducer into [...]

20 2. The epoxy consists of the epoxy itself and a hardener. Remove the two compounds from the package and place them on the paper plate. Thoroughly stir the two compounds together until the mixture has a uniform color and consistency. Do not mix too fast or bubbles will form in the epoxy. After mixing, you have 20 minutes to complete the installat[...]

21 Recommended tools for this job include: drill, 7/8" drill bit, 1/8" drill bit for pilot holes, screwdriver. Required supplies for this job include: four #8 stainless steel wood screws (3/4" long), high quality, marine grade above- or below-waterline sealant. First find a location on the boat's transom where the water flow is [...]

22 Route the sensor's cable through or over the transom to the sonar unit. If you need to drill a hole in the transom to pass the connector through, the required hole size is 7/8". CAUTION: If you drill a hole in the transom for the cable, make sure it is lo- cated above the waterline. After installation, be sure to seal the hole with the[...]

23 connected to another power source. If your NMEA 2000 buss is already powered, you can ignore the NMEA 2000 Power cable. Never attach two power sources to a single NMEA 2000 buss. If you do need to power your NMEA 2000 buss, attach the NMEA 2000 Power cable to your boat's battery just as indicated in the following segment for connecting your[...]

24 For example, if you have to extend the power cable to the battery or power buss, attach one end of the fuse holder directly to the battery or power buss. This will protect both the unit and the power cable in the event of a short. It uses a 3-amp fuse. Power connections for the units in this series. NOTE: If you're powering a NMEA 2000 buss[...]

25 This unit has reverse polarity protection. No damage will occur if the power wires are reversed. However, the unit will not work until the wires are attached correctly. An optional 8-foot, CA-4 external power cable with a cigarette lighter adapter is available from Lowrance. NMEA 2000 Cable Connections NMEA 2000 is a new buss network specificall[...]

26 Cable connections for this unit. Mounting the Unit: Bracket, In-Dash or Portable You can install the unit on the top of a dash with the supplied gimbal bracket. It can also be installed in the dash or mounted on a portable power supply. If you use the supplied bracket, you may be interested in the optional R-A-M  bracket mounting system. This[...]

27 Optional R-A-M mounting system. Bracket Installation Mount the unit in any convenient location, provided there is clearance behind the unit when it's tilted for the best viewing angle. You should also make sure there is enough room behind the unit to attach the power, transducer and data cables. (A drawing on the next page shows the di- men[...]

28 Drill a 1-inch (25.4 mm) hole in the dash for the power, transducer and data cables. The best location for this hole is immediately under the gimbal bracket location. This way, the bracket can be installed so that it covers the hole, holds the cables in position and results in a neat in- stallation. Some customers, however, prefer to mount the b[...]

29 In-Dash Installation You can mount the unit in the dash with an optional FM-5 In-Dash Adapter Kit. The kit includes mounting hardware, a template for cut- ting the hole and an instruction sheet, part 988-0147-43. In-dash mounting template for the sonar unit, showing dimensions. NOTE: The figure above is not printed to scale. A scaled template (F[...]

30 If these accessories are not available from your dealer, see the acces- sory ordering information on the inside back cover of this manual. Visit our web site for a complete listing of all the available accessories for your unit. Face Cover Your unit comes with a white protective cover that snaps on and off the front of the unit. This cover is in[...]

31 Section 3: Basic Sonar Operation This section addresses the unit's most basic sonar operations. The in- structions presented in Sec. 3 follow a chronological order. Sec. 4, Sonar Options & Other Features , will discuss other more advanced functions and utilities. Material in Sec. 4 is arranged in alphabetical order. Before you turn on t[...]

32 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or adjust a feature. 4. ARROW KEYS – These keys are used to navigate through the menus, make menu selections, move the chart cursor and enter data. 5. ENT (Enter) – This key allows you to save data, accept values or execute menu commands. 6. EXIT ?[...]

33 Main Menu. The Main Menu commands and their functions are: Screen command: changes the contrast or brightness of the display screen. Sounds command: enables or disables the sounds for key strokes and alarms and sets the alarm style. Transparency command: adjust the level of transparency for dialogs. Sonar Alarms command: turns sonar alarms on or[...]

34 Pages The unit has five Page display options, accessed by pressing the PAGES key. The list of display options appears in the following image. Pages Menu, showing some Sonar display options. All of the display options show the sonar chart in some format. This is a "cross-section" view of the water column beneath the boat. The chart move[...]

35 Sonar chart display options (from left) split zoom and digital data. Sonar chart display options (from left) FlashGraf and flasher. Sonar Page Menu. Most of these functions are discussed in Sec. 4.[...]

36 Sonar Page, showing full sonar chart mode. You can customize how the Sonar Page displays its pictures and other data in many ways. Your unit also includes several special sonar features and options that can help you better interpret the underwater scene. We'll discuss all of those features and options in Sec . 4, but to show you how easy t [...]

37 Basic Sonar Quick Reference 1. Mount the transducer and unit. Connect the unit to electric power and the transducer. 2. Launch your boat. 3. To turn on the unit, press and release PWR key. 4. Head for your fishing grounds. Your unit automatically displays digi- tal depth and surface water temperature in the corner of the screen. The auto setting[...]

38 Sonar Operations As you can see from the quick reference on the previous page, basic operation is pretty easy, right out of the box. If you are a sonar novice, try operating the unit with the factory defaults until you get a feel for how it's working. As you're learning the basics, there is one setting you might want to tinker with fro[...]

39 You can change the sensitivity level whether you are in Auto Sensitivity mode or Manual Sensitivity mode. The adjustment method works the same in both modes, but it gives you slightly different results. Adjusting sensitivity in Auto Sensitivity Mode is similar to manually ad- justing a car's speed with the accelerator pedal while cruise con[...]

40 NOTE: If you want to change the sensitivity in Manual Mode, first turn off Auto Sensitivity: from the Sonar Page, press MENU | ↓ to A UTO S ENSITIVITY | ENT | ↑ to S ENSITIVITY | ENT . Press ↓ or ↑ to pick a different sensitivity setting. When it's set at the desired level, press EXIT . Important Tip: While you are experimenting and[...]

41 Other Free Training Aids The sonar options section discusses Fish I.D., fish alarms and other features in greater detail. If you or a friend has Internet access, you can also learn more about interpreting what you see on your sonar screen. Visit our web site, WWW.LOWRANCE.COM . Be sure to check out the free Sonar Tutorial, which includes animate[...]

42 Notes[...]

43 Section 4: Sonar Options & Other Features Material in this section is arranged in alphabetical order. ASP  (Advanced Signal Processing) The ASP  feature is a noise rejection system built into the sonar unit that constantly evaluates the effects of boat speed, water conditions and interference. This automatic feature gives you the best [...]

44 2. Press ↓ to N OISE R EJECTION | ENT . 3. Press ↓ or ↑ to select a setting, then press ENT . 4. To return to the previous page, press EXIT | EXIT . Alarms This unit has three different types of sonar alarms. The first is the Fish Alarm. It sounds when the Fish I.D.  feature determines that an echo is a fish. Another alarm is the Zone A[...]

45 To adjust and turn on the shallow alarm: 1. Press ALARM | → to S HALLOW A LARM D EPTH | ENT . 2. Press ↑ or ↓ to change the first number, then press → to move the cursor to the next number and repeat until the depth is correct, then press ENT . 3. Press ← to S HALLOW A LARM E NABLED | ENT | EXIT | EXIT | EXIT . 4. To turn off the alarm[...]

46 At left, Sonar Alarms menu, with Adjust Zone command selected. At right, Adjust Zone Alarm selection box, with Upper selected. 4. Press EXIT | ← to Z ONE A LARM E NABLED | ENT | EXIT | EXIT | EXIT . Now, any echo — fish, bottom, structure — within the zone alarm's depth range will trigger the zone alarm. 5. To turn off the alarm, pres[...]

47 To turn the fish alarm on: 1. Press ALARM | ↓ to F ISH A LARM | ENT | EXIT | EXIT | EXIT . 2. To turn off the alarm, press ALARM | ↓ to F ISH A LARM | ENT | EXIT | EXIT | EXIT . Calibrate Speed The speed sensor can be calibrated to compensate for inaccuracies. Be- fore you change the setting, first calculate the percentage that the speed is [...]

48 At left, Sonar Page menu with Chart Speed command selected. At right, Chart Speed Control Bar. If you do experiment with chart speed, remember to reset it to maxi- mum when you resume trolling or moving across the water at higher speed. To change chart speed: 1. From the Sonar Page, press MENU | ↓ to C HART S PEED | ENT . 2. The Chart Speed Co[...]

49 At left, Sonar Page menu with ColorLine command selected. At right, the ColorLine control bar. To adjust the ColorLine level: 1. From the Sonar Page, press MENU | ↓ to C OLORLINE | ENT . 2. The ColorLine Control Bar appears. Press ↓ to decrease ColorLine; press ↑ to increase Colorline. 3. When it's set at the desired level, press EXIT[...]

50 At left, Sonar Page menu with Depth Cursor command selected. At right, sonar chart with the depth cursor active. The line indicates the school of fish is 31.91 feet deep. The cursor can be moved to any location on the screen, letting you pin- point the depth of a target. 1. From the Sonar Page, press MENU | ↓ to D EPTH C URSOR | ENT . 2. The d[...]

51 2. The Depth Range Control Scale appears. Press ↑ or ↓ to select a dif- ferent depth range. A black bar highlights the selected range. Range numbers in gray cannot be selected. 3. When the new range is selected, press EXIT to clear the menu. Depth Range - Manual You have complete control over the range when the unit is in the man- ual mode. [...]

52 At left, Sonar Page Menu with Upper and Lower Limits command se- lected. At right, Sonar Chart Limits menu, with Upper Limit selected. To change the upper and lower limits: 1. From the Sonar Page, press MENU | ↓ to U PPER A ND L OWER L IMITS | ENT . The Sonar Chart Limits menu appears, with Upper Limit selected. 2. To set the upper limit, pres[...]

53 To turn off upper and lower limits: Reactivate Auto Depth Range. From the Sonar Page, press MENU | ↓ to A UTO D EPTH R ANGE | ENT | EXIT . FasTrack  This feature automatically converts all echoes to short horizontal lines on the display's far right side. The graph on the rest of the screen con- tinues to operate normally. FasTrack give[...]

54 You may see fish symbols on the screen when actually, there are no fish. The reverse is also true. The illustrations on the next page show how Fish I.D. can actually miss fish that are present. Does that mean Fish I.D. is broken? No — the feature is simply inter- preting sonar returns in a specific way to help take some of the work out of read[...]

55 2. Press ↓ to F ISH D EPTHS | ENT | EXIT | EXIT . To turn off FishTrack, repeat the instructions in step 1. Turning off FishTrack in this manner will not turn off Fish I.D. symbols. Sonar Features menu with Fish I.D. Depths selected (at left, dual- frequency menu; center, single-frequency menu). When the che ck box t o the lef t is che ck ed, [...]

56 Sonar Features menu with a frequency of 200 kHz selected. To change the frequency setting to 50 kHz: 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT . 2. Press ↓ to F ISH D EPTHS | → to 50 K H Z | ENT . 3. Press EXIT | EXIT to clear the menu. To change the frequency setting to 200 kHz: 1. From the Sonar Page, press MENU | [...]

57 Overlay Data command on the Sonar Menu, at left. Overlay Data Shown selection menu, right. In this example, we scrolled down the data list to highlight "Ground Speed." When selected, the data type shifts to the top of the data list and a check mark appears beside the data type. (If you wish, you may now use ↓ or ↑ to select other D[...]

58 To change displayed data font size: 1. Press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ or ↑ to select Data Type |press → or ← to Data Size | EXIT . The selected data type will be displayed in the new size. (To change the font size for another Data Type, press ENT and repeat these steps, be- ginning with step two above.) 3. To retur[...]

59 However, when you are running at high speeds, or just want the fastest possible screen update, you may want to use the HyperScroll  feature. When you change the Ping Speed to any setting greater than 50 per- cent, the unit automatically enters HyperScroll mode. These faster ping rates allow you to maintain a high-detail picture on the screen,[...]

60 To turn off HyperScroll: 1. From the Sonar Page, press MENU | ↓ to P ING S PEED | ENT . 2. The Ping Speed Control Bar appears. Press ↓ to decrease ping speed to 50 percent. When it's set at the desired level, press EXIT . When you boost ping speed and switch into HyperScroll, the width of the FasTrack bar graph display doubles in width [...]

61 from an optional water speed sensor. The Water Distance window can be reset to zero using the Reset Water Distance command. Press MENU | MENU | ↓ to R ESET W ATER D ISTANCE | ENT . The menus are cleared and the water distance is reset to 0.00. Set Keel Offset This unit measures water depth from the face of the transducer. Since the transducer [...]

62 1. Press MENU | MENU | ↓ to S ET K EEL O FFSET | ENT . 2. The Keel Offset dialog box appears with a plus (+) sign at the front of the box. 3. Press → to the first number, then press ↑ to change the number to 1. 4. Press → to the second number, them press ↑ to change the num- ber to 5, then press EXIT . The depth indicators now accurate[...]

63 To adjust sensitivity in auto mode: 1. Press MENU | ENT . 2. The Sensitivity Control Bar appears. Press ↓ to decrease sensitivity; press ↑ to increase sensitivity. When it's set at the desired level, press EXIT . (When you reach the maximum or minimum limit, a tone sounds.) At left, Sonar Menu with Sensitivity command selected. At right[...]

64 Sonar Color Mode The default color scheme for the sonar chart is white background, but we offer other variations to suit your viewing preferences. You can se- lect the chart to be displayed in grayscale, reverse grayscale, blue back- ground, or Nightview, IceView, or bottom color tracking. To change the chart mode color scheme: 1. From the Sonar[...]

65 Full Sonar Chart. The Overlay Data (depth and water temperature) are set to different text sizes. Split Zoom Sonar Chart A split chart shows the underwater world from the surface to the bot- tom on the right side of the screen. The left side shows an enlarged ver- sion of the right side. The zoom range shows at the bottom left corner of the scre[...]

66 Digital Data/Chart Customizing the Digital Data/Chart Screen The Digital Data/Chart screen can be customized to show digital data different from the defaults first shown. To customize this screen: 1. From the Sonar Page (in Digital Data mode), press MENU | ↓ to C USTOMIZE | ENT . At left, the Sonar Menu showing the Customize command highlighte[...]

67 Options List for customizing Digital Data boxes. At left, the list first ap- pears with Water Temperature selected. At right, Maximum Speed has been picked to replace Water Temperature in the top digital data box. Tip: You can customize other digital data boxes before returning to the Sonar Page. After changing the first box by selecting the Dat[...]

68 Flasher We've also included a full-screen flasher for those times you need to see all the detail. Like FlashGraf, the Flasher page represents a flasher style sonar, but without the additional data boxes and narrow scrolling chart. Flasher page. Sonar Simulator This unit has a built-in simulator that lets you run it as if you were on the wat[...]

69 screen and a sonar chart plays much like the simulator. Unlike the simulator, the demo mode is for demonstration only, and will auto- matically stop as soon as you turn on the unit with a transducer at- tached. The simulator will continue to function normally. Stop Chart If you are running multiple units on a boat or using this unit in a car, th[...]

70 Sonar Features menu with Surface Clarity selected (at left, dual- frequency menu; at right, single-frequency menu). 2. Press ↓ or ↑ to select clarity level | EXIT | EXIT | EXIT . In the illustration at left, Surface Clarity is turned off. The right view shows Surface Clarity set at High. Upper and Lower Limits See the entry in this section f[...]

71 For example, pressing the ZIN key once will enable a 2X zoom which will show all echoes that are between the top and bottom of the 2X zoom bar. Pressing the key again will give a 4X zoom and only the ech- oes between the top and bottom of the 4X bar will show on the screen. Press the Zoom Out key, ZOUT , to return the display to the normal mode.[...]

72 Notes[...]

73 Section 5: Sonar Troubleshooting If your unit is not working, or if you need technical help, please use the following troubleshooting section before contacting the factory customer service department. It may save you the trouble of returning your unit for repair. For contact information, refer to the last page, just inside the back cover of this[...]

74 3. The water may be deeper than the sonar's ability to find the bottom. If the sonar can't find the bottom signal while it's in the automatic mode, the digital sonar display will flash continuously. It may change the range to limits far greater than the water you are in. If this hap- pens, place the unit in the manual mode, then c[...]

75 To eliminate or minimize the effects of electrical noise, first try to de- termine the cause. With the boat at rest in the water, the first thing you should do is turn all electrical equipment on the boat off. Make sure the engine is also off. Turn your sonar on, then turn off Noise Reject [also known as the ASP feature (Advanced Signal Processi[...]

76 Notes[...]

77 Section 6: Supplemental Material Index A Accessories, 1, 26, 27, 29, 30 Sec. 2, Installation & Accessories , 5 Alarms, 32, 33, 44, 45, 46 Depth Alarms, 44 Fish Alarm, 44, 46, 47 Zone Alarm, 44, 45, 46 Antenna, 75 ASP  (Advanced Signal Processing), 18, 43 B Backlights / Lighting, 2, 31 Batteries, 5, 23, 24, 73, 74, 75 Brightness, 33 C Cali[...]

78 Ping Speed, 56, 58, 59, 60 HyperScroll  , 56, 58, 59 Power, 1, 2, 5, 22, 23, 24, 25, 26, 27, 28, 29, 31, 32, 37, 62, 73, 74, 75 Product Specifications, 2 R Range, 3, 18, 46, 50, 51, 52, 53, 65, 71, 74 Automatic, 50 Manual, 51 Upper and Lower Limits, 51, 70 Reset Options, 33, 40, 60, 63 Reset Water Distance, 33, 60, 61 Route, 5, 7, 13, 14, 15,[...]

79 Notes[...]

80 Notes[...]

81 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use. We warrant this product against [...]

82 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Lowrance parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any product can be returned, you must call customer servi[...]

Accessory Ordering Information for all countries To order Lowrance accessories such as power cables or transducers, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items. To locate a Lowrance [...]

Visit our web site: Lowrance Pub. 988-0156-001 © Copyright 2004 All Rights Reserved Printed in USA 012304 Lowrance Electronics, Inc.[...]