Mazda Tribute (2001) manuel d'utilisation

Before driving Introduction 2 Instrumentation 6 Controls and features 17 Seating and safety restraints 63 Starting and driving Starting 100 Driving 105 Roadside emergencies 132 Servicing Maintenance and care 151 Capacities and specifications 206 Customer assistance 21 1 Index 217 All rights reserved. Reproduction by any means, electronic or mechani[...]

ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regardi[...]

EMISSION WARRANTY The New V ehicle Limited W arranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance W arranties. For a detailed description of what is covered and what is not covered, refer to the W arranty Guide that is provi[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W arning Child Seat T ether Anchorage Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based T raction Control Master Lighting Switch Ha[...]

V ehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System Engine A[...]

RSM CST SET ACC OFF ON Instrument cluster (pg. 8) W indshield wiper/ washer control (pg. 42) Manual tilt steering wheel lever (pg. 38) Speed controls* (pg. 38) Instrument panel dimmer control (pg. 17) Power mirror control* (pg. 17) Fog lamp control* (pg. 48) Headlamp and turn signal control (pg. 48) * if equipped Instrumentation 6[...]

OFF AM/FM TAPE CD SCAN 12 3 45 6 LOAD CLOCK AUTO-M PRO RPT RDM/BS TR/ APC TR/ APC FF REW TUNE SEEK DISC PUSH POWER VOL PUSH AUDIO CONT LOCK Audio system (pg. 22) 4wd control* (pg. 18) Climate controls (pg. 19) Auxiliary power point (pg. 51) Rear window defroster control (pg. 18) Hazard flasher control (pg. 132) Instrumentation 7[...]

W ARNING LIGHTS AND CHIMES Service engine soon Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD I[...]

These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the light should turn off. (A driving cycle consists of a cold engine startup fo[...]

Air bag readiness Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately . Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating [...]

T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter . High beams Illuminates when the high beam headlamps are turned on. Speed control This li[...]

Engine oil pressure Momentarily illuminates when the ignition is turned to the ON position. Illuminates when the oil pressure falls below the normal range when the engine is running. T o avoid engine damage, stop the vehicle as soon as safely possible and switch off the engine immediately . Check the oil level and add oil if needed. Refer to Engine[...]

Low coolant (if equipped) This lamp will illuminate when the engine coolant inside the reservoir is low . This lamp will illuminate when the ignition is first turned to the ON position, but then should turn off. If the lamp stays on, to avoid engine damage you should allow the engine to cool down, then check the coolant level inside the reservoir .[...]

Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter . Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and any door , liftgate or liftgate window is opened. Headlamps ON warning chime Sounds when the he[...]

NOTE: This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Speedometer I[...]

Odometer Registers the total kilometers (miles) of the vehicle. T rip odometer Registers the kilometers (miles) of individual journeys. Press and hold the button for 1 or more seconds to reset. Press and release the button in less than 1 second to toggle between odometer and trip odometer . Instrumentation 16[...]

INSTRUMENT P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim. POWER MIRROR CONTROL The ignition must be in the ACC or ON position to adjust the power side view mirrors. T o adjust your mirrors: 1. Rotate the control clockwise to the ri[...]

Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. FOUR WHEEL DRIVE (4X4) CONTROL (IF EQUIPPED) This control operates the four wheel drive (4X4) system. Refer to the Driving chapter for more information. REAR WINDOW DEFROSTER CONTROL The rear defroster control is located on the inst[...]

CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will[...]

NOTE: In snowy or dirty conditions, leave the mode selector in the OFF position. • MAX A/C- Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster . Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from en[...]

• (Defrost)-Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 6°C (43°F) or higher , the air conditioner will automatically dehumidify the air to reduce fogging. Operating tips • In humid weather , select before driving. This will reduce fogging [...]

USING YOUR AUDIO SYSTEM AM/FM Radio with Compact Disc Player V olume/power control Ensure that the ignition switch is in the ACC or ON position. Press the control to turn the audio system on. T urn the control to raise or lower the volume. Press the control again to turn the audio system off. NOTE: T o prevent the battery from being discharged, do [...]

Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move up the frequency band in individual increments. • Press to move down the frequency band in individual increments. Seek function The seek function control works in radio mode. Seek function in radio mode Press and momentarily hold the SEEK control. A beep[...]

Scan function The scan function works in radio mode. Scan function in radio mode Press the SCAN control to hear a sampling of strong stations on the frequency band. Each station will play for approximately 5 seconds. Press the SCAN control again to remain on a station and disable this mode. CD select • T o begin CD play (if CD is loaded), press t[...]

Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the AUDIO control until BASS is illuminated in the display . T urn the volume control to adjust to the desired level of bass. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the AUDIO control u[...]

Radio station memory preset The radio is equipped with five station memory preset controls. These controls can be used to select up to five preset AM stations and ten FM stations (five in FM1 and five in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM control. 2. Select the desired station. 3. Press and momentarily [...]

Random play in CD mode Press the RDM control during play . RDM will illuminate in the display . The next selection will be randomly selected. T o disengage random play , press the RDM control again. Repeat play The repeat play feature works in CD mode and repeats the current CD selection. Repeat play in CD mode Press the RPT control during play . R[...]

3:24, the time will change to 3:00. If the clock’ s current time setting is within the latter part of the hour (from 30 to 59 minutes), the hour setting will automatically advance one hour . For example, if the original setting is 3:45, the time will change to 4:00. Changing the display mode Press the CLOCK control to alternate the display betwee[...]

V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If the ignition or power is turned off, the las[...]

Tune/Seek/Disc function in radio mode • Press to find the next available station up the frequency band. • Press to find to the next available station down the frequency band. Tune/Seek/Disc function for CD mode • Press to select the next disc in the CD changer . • Press to select the previous disc in the CD changer . Scan function The scan [...]

Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Press the AUDIO control twice to access the system’ s treble adjust mode. T urn the control to increase (right) or decrease (left) the amount of treble output. Bass adjust The bass adjust control allows you to increase or decrease the a[...]

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the AUDIO control four times to access the system’ s balance adjust mode. T urn the control (right or left) to adjust between the right and left speakers. Radio station memory preset The radio is equipped with five station memory preset co[...]

3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. T o deactivate autoset and return to your audio system’ s manually se[...]

T ape direction select Press the PRO control to play the alternate side of a tape. When the end of the cassette is reached, the audio system will automatically reverse play . Repeat play The repeat play feature works in CD mode and repeats the current CD selection. Repeat play in CD mode Press the RPT control during play . RPT will illuminate in th[...]

Multiple CD loading This feature allows you to autoload up to 6 discs into the multi disc CD player internal to the radio. Press and hold the LOAD control until a beep is heard. When IN is displayed, insert the CD. When IN is displayed again, insert the next CD. The first CD will automatically play when: • there is not a CD inserted for 15 second[...]

T roubleshooting the CD changer (if equipped) W ARNING: The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • Y ou may be traveling on a rough road, playing badly scratched discs or the disc may be dirty . Skipping will not scratch the discs or damage the player . If your [...]

Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their stre[...]

MANUAL TILT STEERING COLUMN Push the tilt steering wheel lever downward to move the steering wheel up or down. Pull the control up into the original position to lock the steering wheel in position. W ARNING: Never adjust the steering wheel when the vehicle is moving. Y ou could lose control of the vehicle. SPEED CONTROLS (IF EQUIPPED) T o turn spee[...]

W ARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. Y ou may lose control of the vehicle. W ARNING: Do not shift the gearshift lever into N (Neutral) with the speed control on. Y ou may lose control of the vehicle or cause engine system damage. T o turn speed control off • Press OFF . NOTE:[...]

Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If your vehicle slows down more than 16 km/h (10 mph) below your set speed on [...]

• Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC. T o disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). NOTE: Disengaging the speed control will not erase the previously programmed set speed. NOTE: Fully depressing the clutch pedal may cause a flare in engine RPM [...]

NOTE: Pressing OFF will erase the previously programmed set speed. T o return to a previously set speed • Press RSM. NOTE: For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph). WINDSHIELD WIPER AND W ASHER For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. ON O[...]

For normal or low speed wiper operation, move control down two positions from OFF . For high speed wiper operation, move control down three positions from OFF . T o activate the windshield washer , pull control toward you. Release control to stop washer fluid spray . MIST FUNCTION Move control up and release for one wipe. Controls and features 43[...]

Rear window wiper/washer controls For intermittent operation of rear wiper , rotate end of control upward to the INT position. For normal speed rear wiper operation, rotate control upward to ON. T o activate the rear washer , rotate control the icon and release. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console wil[...]

Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the V elcro y pad from the storage compartment door . • Place V elcro y on aftermarket transmitter opposite of actuator control. • Install the transmitter on to storage compartment door a[...]

W ARNING: Do not let children play with the moon roof. They may seriously injure themselves. INTERIOR LAMPS Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the RUN position. • the control is in the DOOR position and any door is open. • the headlamp control [...]

The map lamp controls (without moon roof) are located on the dome lamp. Press the controls on either side of each map lamp to activate the lamps. If equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the controls on either side of each map lamp to activate the lamps. HEADLAMP CONTROL Rotate the headlamp contr[...]

High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. FOG LAMP CONTROL (IF EQUIPPED) The fog lamps can be turned on when the headlamp control is in eith[...]

POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down • Press AUTO completely down to the second detent. The driver’ s window will open fully . Depress up to stop window operation. NOTE: This f[...]

Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the right side of the control. Press the left side to restore the window controls. POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. CHILDPROOF DOOR LOCKS W[...]

CENTER CONSOLE Y our vehicle may be equipped with a variety of console features. These include: • Utility compartment • Cupholders • Ashcup W ARNING: Use only soft cups in the cupholder . Hard objects can injure you in a collision. AUXILIARY POWER POINT W ARNING: Power outlets are designed for accessory plugs only . Do not hang any type of ac[...]

T RUCK BED AUXILIARY POWER POINT An additional auxiliary power point is located in the cargo area. W ARNING: Power outlets are designed for accessory plugs only . Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . CARGO COVER (IF EQUIPPED) Y our vehi[...]

W ARNING: Do not place any objects on the cargo area cover . They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. W ARNING: The cover may cause injury in a sudden stop or accident if it is not securely installed. LIFTGATE T o open the rear window , pull the right side of the liftgate handle. T [...]

Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. The remote entry system allows you to lock or unlock all vehicle doors without a key . The remote entry features only operate with the ignition in the LOCK position. If there is any potential remote ke[...]

Sounding a panic alarm Press this control to activate the alarm. T o deactivate the alarm, press the control again. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating[...]

Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’ s memory , or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • T ake all your vehicle’ s transmitters to your authorized Mazda dealer for programming, or • Perform the progr[...]

• When you have completed programming the remote transmitters, turn the ignition to 1 (LOCK) or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s). The system automatically turns off after 30 seconds[...]

The light in the instrument cluster will flash every two seconds when the vehicle is armed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. The theft light will illuminate for three seconds and then go out. If the light stays on for an extended period of time or flashes rapidly , have the syst[...]

NOTE: These objects and devices cannot damage the P A TS ignition key , but can cause a momentary issue if they are too close to the key during engine start. NOTE: If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key . Check to make sure the encoded ignition key is an a[...]

1. Insert the first previously programmed coded key into the ignition and turn the ignition from 2 (ACC) to 3 (ON) (maintain ignition in 3 (ON) for at least one second). 2. T urn ignition to 1 (LOCK) and remove the first coded key from the ignition. 3. W ithin ten seconds of turning the ignition to 2 (ACC), insert the second previously programmed c[...]

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will respond if unauthorized entry is attempted. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to authorized Mazda dealership, to aid in troubleshooting. Arming the system When armed, this syst[...]

Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter . • Unlock the doors with a key . • Press the panic control on the remote entry transmitter . This will disarm the system only if the alarm is sounding. Controls and features 62[...]

SEA TING Adjusting the front manual seat W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. Sudden braking or a collision could cause serious injury . Adjust the seat only when the vehicle is stopped. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden[...]

Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. This can cause you to lose control of the vehicle and cause an accident. W ARNING: Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. W AR[...]

Move the rear of the control up or down to raise or lower the rear portion of the seat cushion. Move the control in the directions shown to move the seat forward, backward, up or down. REAR SEATS Head restraints (if equipped) Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head res[...]

Push control to lower head restraint. Folding down rear seats 1. Raise the rear seat head restraint and remove. 2. Place the head restraints under the front passenger seat for storage. 3. Pull the seat release control. Seating and safety restraints 66[...]

4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE: When the seatback release strap is pulled use your other hand to guide the seatback. Seating and safety restraints 67[...]

6. Rotate seatback down into load floor position. W ARNING: Make sure seat belt buckle heads are not trapped underneath the seatback and that the seat belt buckle heads are fully extended towards the front of the vehicle. Seat belt buckle heads may break if they are trapped underneath the seatback as the seatback is rotated down. NOTE: Make sure th[...]

2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed. 3. Remove the head restraints stored under the front passenger seat and return them to the original position on the seat backs. T o remove the rear cushion 1. Pull the Y ellow tab 2. Pull the cushi[...]

T o install the rear cushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Safety restraints precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. W ARNING: T o reduce the risk of injury , make sure childre[...]

W ARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using[...]

W ARNING: After any vehicle collision, the safety belt system at all outboard seating positions (except driver , which has no “automatic locking retractor” feature) must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly . In addition, all safety belts [...]

The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: V ehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements[...]

• Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retrac[...]

Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height adjuster down. T o raise the height of the shoulder belt, sli[...]

Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.[...]

The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... 9 Crashes are rare events 9 36,700 crashes occur every day . The more we drive, the more we are exposed to 9 rare 9 events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lif[...]

One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only . Deactivating/activating the belt minder feature Read step s1-9 thoroughly before proceeding with the deactivation/ activation programming procedure. The Belt Minder feature can be deactivate[...]

6. W ithin seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7. Confirmation of disabling Belt Minder is provided by flashing the safety belt warning light four times per second for three s[...]

AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. W ARNING: Air bags DO NOT inflate slowly or gently and the risk of injury from a depl[...]

W ARNING: National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’ s chest and the driver air bag module. W ARNING: Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Steps you can take to properl[...]

Children and air bags For additional important safety information, read all information on safety restraints in this guide. W ARNING: Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these inst[...]

The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small [...]

• diagnostic module • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if t[...]

W ARNING: Side Air Bag Storage Areas: Attaching things to the seat in such a way as to cover the outboard side of the seat in any way is dangerous. In an accident the object could interfere with the side air bag, which inflates from the outboard side of the front seats, impeding the added protection of the side air bag system or redirecting the air[...]

W ARNING: Modification of the Supplemental Restraint System Modifying the components or wiring of the supplemental restraint system is dangerous. Y ou could accidentally activate it or make it inoperable. Don’ t make any modifications to the supplemental restraint system. This includes installing trim, badges, or anything else over the air bag st[...]

How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagn[...]

W ARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag i[...]

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air Bag Supplemental Restraint System (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions NOTE: Y ou are required by law to use safety restraints for children[...]

W ARNING: Do not leave children, unreliable adults, or pets unattended in your vehicle. T o improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Mazda recommends use of a belt-positioning booster seat that is labelled as conforming to all applicable Federal motor vehicle safety standards. Belt-positioning boos[...]

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or co[...]

Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats with tether straps. W ARNING: Carefully follow all of the manufacturer’ s instructions inc[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

[...]

W ARNING: If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. If the safety seat is not anchored properly , the risk of a child being injured in a collision greatly increases. 4. Clip the tether strap to the anchor as shown. 5. Refer to the Installing child safety seats in com[...]

LA TCH anchors for child seat installation have been provided in your vehicle at the following locations: The anchors at the center of the rear seat are much further apart than the sets of lower anchors for child seat installation at other seating positions. Some LA TCH equipped child seats can be placed in the center position and will reach the ne[...]

W ARNING: Always attach the LA TCH child restraint to both LA TCH lower anchors in any vehicle seat, being sure to confirm that both LA TCH attachments are fully engaged by pulling back and forth vigorously . A child seat retained on only one side is creating the risk of throwing the child around the vehicle or even out of the seat and vehicle duri[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. NOTE: This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Onl[...]

2. Make sure the headlamps and vehicle accessories are off. If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 3[...]

Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. NOTE: If the driver’ s safety belt is fastened, the light may not illuminate. ST ARTING THE ENGINE 1. T urn the key to 4 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key [...]

Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below . For best resul[...]

Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . NOTE: Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other d[...]

BRAKES Y our service brakes are self-adjusting. Refer to the service maintenance section for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the b[...]

W ARNING: The Anti-Lock system does not decrease the time necessary to apply the brakes or always reduce stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. ABS warning lamp ABS (if equipped) The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to th[...]

Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, apply the brake pedal and pull the parking brake handle up as far as possible. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. W ARNING: Always se[...]

STEERING Y our vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. T o prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running. • Do not operate the vehicle with a low powe[...]

W ARNING: V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle dif ferently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily und[...]

Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transaxle may occur . Do not rock the vehicle for more than a few minutes or damage to the transaxle and tires may occur or the engine may overheat. W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off [...]

Understanding gearshift positions Y our automatic transaxle electronically controls the shift feel by using an adaptive learning strategy . This feature is designed to optimize shift smoothness. NOTE: It is normal for your transaxle to shift firmly during the first few hundred kilometers (miles) of operation until the adaptive strategy has been lea[...]

N (Neutral) W ith the gearshift lever in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. Overdrive — column mounted gearshift with O/D off switch The Overdrive position with the O/D OFF switch not depressed is the normal driving position for this automatic overdrive trans[...]

When to use D (Drive) or press the O/D OFF switch Y ou will notice that there is only one drive position on your gearshift indicator (instead of Drive and Overdrive). However , you will find a control labeled OVERDRIVE located on the gearshift lever . Push in the switch and the O/D OFF light in the instrument cluster will illuminate. W ith the O/D [...]

1 (First) Use 1 (First) for when added engine braking is desired when descending steep hills. The automatic transaxle will shift to the proper gear to ascend any grade without any need to shift to 1 (First). T o avoid damage to the engine and/or transaxle do not go faster than 56 km/h (35 mph) when in this gear . Y ou can upshift from 1 (First) to [...]

2. Hold down the brake pedal. 3. Depress the clutch pedal. 4. W ithout depressing the accelerator pedal, turn the ignition to position 4 (ST ART), release the ignition as soon as the engine starts. 5. Let the engine idle for a few seconds. 6. Release the brake pedal, then slowly release the clutch pedal while pressing down slowly on the accelerator[...]

Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transaxle. Put the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse). NOTE: Y ou can shift into R (Reverse) only by moving the gearshift lever from left of 3 (Third) an[...]

2. Set the parking brake. 3. Shift into 1 (First). 4. T urn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key . W ARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . 1 24 R 3 5 4 3 2 1 Driving 117[...]

FOUR WHEEL DRIVE (4X4) SYSTEM (IF EQUIPPED) 4x4 system general information W ARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter . Y our vehicle is equipped with a 4x4 system. This 4x4 system can use all four wheels to power the vehicle. This helps increase traction[...]

increase tire wear and may damage driveline components. The 4x4 ON mode is intended for use only on consistently slippery or loose surfaces. • If your vehicle is equipped with this 4x4 system, a spare tire of a different diameter than the road tires should never be used. Such a tire could result in damage to driveline components and make the vehi[...]

• Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. Y ou should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. If your vehicle gets stuck If the vehicle is stuck in mud or snow select the 4x4 ON operating mode. It may be rocked out by shift[...]

NOTE: If the transaxle Power T ake Off unit or rear axle are submerged in water , their fluids should be checked and changed, if necessary . W ater intrusion into the transaxle may damage the transaxle. NOTE: If the rear axle is submerged in water , the rear axle lubricant should be checked and changed, if necessary . The rear axle is filled with a[...]

• When braking, apply the brakes as you normally would. In order to allow the anti-lock brake system (ABS) to operate properly , keep steady pressure on the brake pedal. • Allow more stopping distance and drive slower than usual. Consider using one of the lower gears. V EHICLE LOADING Before loading a vehicle, familiarize yourself with the foll[...]

• Maximum T railer W eight: Maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow . It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. • T railer W eight Range: Specified weight range that the trailer must fall within that ranges fro[...]

Special loading instructions for owners of pickup trucks and utility-type vehicles W ARNING: For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this owner guide. W ARNING: Loaded vehicles, with a higher center of gravity , may handle differently than [...]

Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. T RAILER TOWING T railer towing with your vehicle may require the use of a trailer tow option package. T railer towing puts additional loads on your vehicle’ s engine, transaxle, axle, brakes, tire[...]

T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in: • engine damage • transmission damage • structural damage • loss of control • personal injury Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle. See[...]

Trailer lamps T railer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your authorized Mazda dealer for proper instructions and equipment for hooking up trailer lamps. Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control [...]

• V ehicles with trailers should not be parked on a grade. If you must park on a grade, place wheel chocks under the trailer’ s wheels. Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above the bottom edge of the rear bumper and • Do not allow waves to[...]

LUGGAGE RACK Y our vehicle is equipped with a roof rack. The maximum load for the roof rack is 44 kg (100 lbs), evenly distributed on the crossbars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the crossbars as possible. Always use the adjustable tie down loops to secure the load. T O ADJUST TH[...]

2. Slide the cross-bar to the end of the rail. 3. Use a long, flat object in order to depress the tongue in the endcaps on both sides of the cross-bar . 4. Slide the cross bar assembly and the tie down loop off the end of the rail. T O REINSTALL THE CROSS-BAR ASSEMBLY TO THE ROOF RACK SIDE RAILS: 1. Ensure that both cross-bar assemblies are install[...]

2. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 3. Slide the tie down loops and the cross-bar assemblies over the end cap tongue and into the side rails. 4. T ighten thumbwheel at both ends of the cross-bar . Driving 131[...]

HAZARD FLASHER CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on the instrument panel above the radio. • Depress hazard lights control to activate all hazard flashers simultaneously . • Depress[...]

1. T urn the ignition to the LOCK/OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. T urn the ignition to the ON position. Pause for a few seconds and return the key to the LOCK/OFF position. 5. Make a further check for leaks in the fuel system[...]

Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Canister V ent Control Solenoid 2 5A Blower Relay (coil), Rear Defrost Relay (coil), Pressure Switch to PCM 3 10A Rear W iper Motor , Rear W asher Motor , Rear W iper Relay (coil) 4 10A Four Wheel Drive Control Module, Cluster (Rest[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 8 10A Cluster , Shift Lock Relay (coil), O/D signal to PCM 9 3A PCM Relay (coil), Fan Relay 1, 2, 3 (coil), A/C Relay (coil) 10 20A Front W iper Motor , Front W asher Motor , INT Relay 11 10A IGN Relay (coil), ACC Relay (coil), Starter Relay (coil), Key Interlock Solen[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 26 30A Power Door Lock Motor - Right Front, Left Front, Right Rear , Left Rear , GEM (Door Lock Relay Coil), Power Seat 27 10A Audio, Cluster , Interior Lamp, Map Lamp Cargo Lamp ACC — Accessory Relay Power distribution box The power distribution box is located in th[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description Horn 15A Horn H/L LH 15A* Headlamp (High/Low Left, High Beams) H/L RH 15A* Headlamp (High/Low Right,, High Beams) EEC 5A* EEC (KPWR) HEGO 15A* HEGO 1,2, CMS 1,2, VMV FUEL 20A* Fuel Pump, EEC (FPM) DIODE — — MAIN 120A HEGO 15A ALT [...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description DIODE — — H/L RELA Y MICRO — Headlamp (High/Low , Right/Left Relay) —— — INJ 30A** EEC (VPWR), EVR, MAF , IAC, Bulkhead MAIN 120A Main AL T 15A* Alternator/ Regulator (DRL) 15A* DRL Unit (feed), DRL Relay (DRLZ) (HEL V) 15A*(DRLZ) 10A(HLEV) Daytime Running Lamps (DRL[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description FUEL PUMP ISO — Fuel Pump Relay MAIN F AN ISO — Low Speed Fan Control Relay (2.0L Engine) High Speed Fan Control Relay 1 (3.0L Engine) ADD F AN ISO — High Speed Fan Control Relay 1 (2.0L Engine) Low Speed Fan Control Relay (3.0L Engine) DEF RELA Y ISO — Rear Defroster Re[...]

W ARNING: If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load [...]

1. Park on a level surface, activate hazard flashers and place gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission). 2. Set the parking brake and turn engine OFF . 3. Block the diagonally opposite wheel. 4. Lift the cargo cover and remove the jack handle and lug nut wrench from underneath the cover and the spare[...]

6. Locate the jack notch closest to the tire you are changing, then place the jack on the notch. 7. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. Never use the differentials as a jacking point. It is too easy for the vehicle to tilt or fall and you can be injured[...]

11. Remove the jack and fully tighten the lug nuts in the order shown. 12. Put flat tire, jack, jack handle and lug nut wrench away . Make sure jack is fastened so it does not rattle when you drive. 13. Unblock the wheels. JUMP STARTING YOUR VEHICLE W ARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. [...]

• Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. • T urn the heater fan on in both vehicles to protect any electrical surges. T urn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+)[...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’ s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding poin[...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a slingbelt towing procedure. If your vehicle i[...]

If the vehicle is towed by other means or incorrectly , vehicle damage may occur . In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle (regardless of powertrain configuration) can be flat towed (all wheels on the ground) under the following conditio[...]

INTRODUCTION Be extremely careful to prevent injury to yourself and others and damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an Authorized Mazda Dealer . Factory-trained[...]

SCHEDULE 1 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Km 12 24 36 48 60 72 84 96 108 120[...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Km 12 24 36 48 60 72 84 96 108 120 132 144 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.5) (95) CHASSIS and BODY Brake lines, hoses and connections I I I Disc brakes I I I Dr[...]

SCHEDULE 2 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 [...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) ELECTRICAL SYSTEM Function of all lights I IIIIIIIIII I CHASSIS and BODY Brake lines, hoses and [...]

PRECAUTIONS WHEN SERVICING YOUR VEHICLE Be especially careful when inspecting or servicing your vehicle. T o avoid damage and/or personal injury: • Do not work on a hot engine. • When the engine is running, make sure that loose clothing, jewelry or long hair does not get caught up in moving parts. • Do not work on a vehicle with the engine ru[...]

• Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels to prevent the vehicle from moving unexpectedly . Do not start your engine with the air cleaner removed and do not remove it while the engine is running. 1. Inside the vehicle, pull the hood release handle located under [...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L DOHC I4 Zetec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil filler cap 8. Engine oil dipstick 9. W indshield washer fluid reservoir 5 6 7 8 1 2 3 4 9 Maintenance and care 158[...]

3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10. W indshield washer fluid reservoir 10 9 8 7 1 2 3 4 5 6 Maintenance and care 159[...]

ENGINE OIL Checking the engine oil Refer to the service maintenance section for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (a[...]

• 3.0L DOHC V6 Duratec engine 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN-MAX or ADD-FULL marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN or ADD mark, add enough oil to raise the level within the MIN–MAX or ADD-FULL range. • [...]

• 3.0L DOHC V6 Duratec engine • Oil levels above the MAX or FULL mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the eng[...]

Engine oil and filter recommendations SAE 5W -20 engine oil is recommended Look for this certification trademark. Use SAE 5W -20 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API certification trademark will meet all requirements for your vehicle’ s engine. Do not use supplemental eng[...]

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance section for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir . 2. Visually inspect the fluid level. 3. If necessary , add brake fluid from [...]

W ARNING: Do not let the fluid level in the reservoir for the master cylinder fall below the MIN mark. If master cylinder runs dry , this may cause the brakes to fail. CLUTCH FLUID (MANUAL TRANSAXLE) The clutch master cylinder and brake master cylinder are part of the same system; both are refillable through the brake master cylinder with brake flu[...]

NOTE: State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. W asher fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’ s paint finish, wiper blades or washer system. W ARNING:[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance section for service interval schedules. • Be sure to read[...]

W ARNING: Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. The cooling system in your vehicle is filled with green-colored Mazda Premium Engine Coolant meeting Mazda specifications. T o determine your vehicle’ s coolant type (co[...]

reservoir when the engine is cool. Add the proper mixture of coolant and water to the “cold full” level. For all other vehicles, which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.[...]

If you have to add more than 1.0 liter (1.0 quart) of engine coolant per month, have your dealer check the engine cooling system. Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Not all coolant recycling processes produce coola[...]

decrease the corrosion protection characteristics of the engine coolant and may cause engine damage. • decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • refer to the chart on the coolant container to ensure the coolant concentration in your [...]

4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir . T RANSMISSION FLUID Chec[...]

5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the [...]

If necessary , add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Checking and adding manual transmission fluid 1. [...]

Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells. If the electrolyte level in the battery is low , you can add plain tap water to the battery , as long as you do not use hard water (water with a high mineral or alkali content). If possible, however , try to only fill the battery cells with d[...]

W ARNING: Battery posts, terminals and related accessories contain lead and lead compounds. W ash hands after handling. Because your vehicle’ s engine is electronically controlled by a computer , some control conditions are maintained by power from the battery . When the battery is disconnected or a new battery is installed, the engine must relea[...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. AIR FILTER MAINTENANCE Refer to the service maintenance section for the appropriate intervals for changing the air filter element[...]

7. Replace the air filter housing cover and secure the clamps. 8. Replace the air inlet tube and secure the clamp. W ARNING: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be voided for any damage to the engine if the correct air filter element is not used. WINDSHIELD WIPER BLADES Check t[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are [...]

T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire li[...]

Tire rotation Because your vehicle’ s tires perform different jobs, they often wear differently . T o make sure your tires wear evenly and last longer , rotate them as indicated in the service maintenance section. If you notice that the tires wear unevenly , have them checked. • Four tire rotation • Five tire rotation Maintenance and care 181[...]

Replacing the tires Replace the tires when the wear band is visible through the tire treads. W ARNING: When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity . Use only t[...]

USING SNOW TIRES AND TRACTION DEVICES NOTE: Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all-weather treads to provide traction in rain and snow . However , in some climates, using snow tires and traction devices may be necessary . See your authorized Mazda dealer for mor[...]

W ARNING: If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury . W ARNING: Automotive fuels can cause serious injury or death if misused or mishandled. W ARNING: Gasoline may contain benze[...]

• Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water . Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other f[...]

Choosing the right fuel • Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. • Do not use fuel containing methanol. It can damage critical fuel system components. • Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containin[...]

Many of the world’ s automakers issued the W orld-wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the W orld-wide Fuel Charter should be used when available. Ask your fuel supplier about gasolines that meet the W orld-wide Fuel C[...]

5. T urn the filler cap clockwise 1/8 of a turn until it stops. After refueling, if the “CHECK FUEL CAP” indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed. T urn off the engine, remove the fuel filler cap, align the cap properly and reinstall it securely . The indicator should turn off [...]

miles) of driving (engine break-in period). Y ou will get a more accurate measurement after 3,000 km–5,000 km (2,000 miles-3,000 miles). Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities section of the Capacities and specificatio[...]

3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles[...]

• W arming up a vehicle on cold mornings is not required and may reduce fuel economy . • Resting your foot on the brake pedal while driving may reduce fuel economy . • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of ali[...]

It is important to note the box in the lower left corner of the window sticker . These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions. Y our fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control comp[...]

sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’ s emission system is on the V ehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and give[...]

• License plate lamp • T ail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2.[...]

5. Squeeze the retainer spring together releasing it from bulb hooks and rotate it away from the bulb. 6. W ithout turning, carefully pull bulb out of headlamp assembly . Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hands could cau[...]

Replacing brake/tail/turn/backup lamps bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly . 3. Carefully remove the lamp assembly by pulling it [...]

5. Pull the bulb straight out of the socket and push in the new bulb. 6. T o complete installation, follow the removal procedure in reverse order . Replacing fog lamp bulbs (if equipped) 1. Remove the bulb socket from the fog lamp by turning counterclockwise. 2. Disconnect the electrical connector from the fog lamp bulb. 3. Connect the electrical c[...]

Replacing high-mount brake lamp bulbs For bulb replacement, see an authorized Mazda dealer . Replacing the interior bulbs Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp For bulb replacement, see an authorized Mazda dealer . USING THE RIGHT BULBS Replacement bulbs are specified in the chart be[...]

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized Mazda dealer . V ERTICAL AIM ADJUSTMENT 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen dir[...]

4. On the wall or screen you will observe a light pattern with a distinct horizonal edge of high intensity light with a slight angle towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted. 5. Locate the vertical adjuster on each headlamp, then us ea7m mh e x socket or T20 T orx driver to turn the [...]

Deposits not removed promptly can cause damage to the vehicle’ s paintwork. Remove any exterior accessories, such as antennas, before entering a car wash. If you have wax applied to the vehicle at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield. After[...]

• T ake care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water when the engine is hot to avoid cracking the engine block or other engine components. • Never apply anything to the drive belt (including belt dressing). • 2.0L DOHC I4 — Zet[...]

• Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels W ash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel s[...]

Cleaning seats equipped with side air bags Remove dust and loose dirt with a whisk broom or a vacuum cleaner . Remove fresh spots immediately . Follow the directions that come with the cleaner . Do not saturate the seat cover with upholstery cleaner . W ARNING: Do not use chemical solvents or strong detergents when cleaning the seat where the side [...]

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. W ARNING: Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been invo[...]

REFILL CAPACITIES Fluid Classification Application Capacity Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid All Fill to line on reservoir Engine oil (including filter change) SAE 5W -20 Super Premium Motor Oil 2.0L I4 Zetec engine 4.25L (4.5 quarts) 3.0L V6 Duratec engine 5.2L (5.5 quarts) Fuel tank N/A 2.0L I4 Zetec engine 57L (15 ga[...]

Fluid Classification Application Capacity Engine coolant 4 Use only ethylene- glycol-based coolant 2.0L I4 Zetec engine with manual transaxle 5.0L (5.3 quarts) 3.0L V6 Duratec engine with automatic transaxle 10.0L (10.6 quarts) Rear axle lubricant SAE 80W -90 Premium Rear Axle Lubricant 4X4 1.4L (2.96 pints) 5 W indshield washer fluid n/a All 2.6L [...]

WHEEL AND TIRE SIZES V ehicle Grade Wheel T ire Spare Wheel Spare T ire DX/DX-V6 6.5JJx16 215/70R16 17x4T 135/90R17 LX-V6/ES-V6 7.0JJx16 235/70R16 17x4T 145/90R17 ENGINE SPECIFICATIONS Engine 2.0L DOHC I4 Zetec engine 3.0L DOHC V6 Duratec engine Cubic inches 121 181 Required fuel 87 octane 87 octane Firing order 1-3-4-2 1-4-2-5-3-6 Spark plug gap 1[...]

3 2 1 5 4 Capacities and specifications 209[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side. V ehicle identification number [...]

Customer Assistance (Except Puerto Rico) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicin[...]

This way , we can be sure to respond to you as efficiently as possible. That is our goal. If you live outside the U.S.A., please contact your nearest Mazda Distributor . Customer Assistance (Puerto Rico) Y our complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your [...]

If you would like to write a letter , please address it to the following, Attn: Customer Assistance, which corresponds with your state: REGIONAL OFFICE Mazda North American Operations 7755 Irvine Center Drive Irvine, CA 92618–2922 P .O. Box 19734 Irvine, CA 92623–9734 This way , we can be sure to respond to you as efficiently as possible. That [...]

Y ou may have these problems if you do: • Recommended fuel may be unavailable. Any kind of leaded fuel or low-octane fuel will affect vehicle performance and damage the emission controls and engine. • Proper repair facilities, tools, testing equipment, and replacement parts may not be available. The manufacturer’ s warranty applies only to Ma[...]

Reporting Safety Defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Mazda Motor Corporation (Y our Mazda Importer/Distributor). If NHTSA receives similar complaints, it may o[...]

PUBLICA TION ORDER NUMBER PUBLICA TION DESCRIPTION 9999 95 062B 01 2001 WORKSHOP MANUAL 9999 95 038G 01 2001 WIRING DIAGRAM 9999 95 014C 01 2001 OWNER’S MANUAL WORKSHOP MANUAL: Covers recommended maintenance and repair procedures of the drive train, body and chassis. WIRING DIAGRAM: Provides electrical schematics as well as component location for[...]

A Air bag supplemental restraint system .................... 81, 85 and child safety seats ..............83 description ..........................81, 85 disposal ......................................89 driver air bag ......................83, 88 indicator light ............... 10, 85, 89 operation ............................. 83, 88 passenger air[...]

instrument panel .................... 204 interior .....................................204 mirrors ..................................... 205 plastic parts ............................ 203 safety belts ..............................205 washing .................................... 200 waxing ..................................... 201 wheels .........[...]

F Fluid capacities ......................... 206 Foglamps ..................................... 48 Four -Wheel Drive vehicles description .............................. 118 driving off road ....................... 119 indicator light ................... 12, 119 preparing to drive your vehicle ..................................... 108 Fuel .........[...]

Infant seats (see Safety seats) ..92 Inspection/ maintenance (I/M) testing .......193 Instrument panel cleaning ...................................204 cluster ..........................................8 lighting up panel and interior .....................17 location of components ..............8 J Jack ............................................ 1[...]

Motorcraft parts ........................188 O Octane rating ............................ 186 Odometer .....................................16 Off-Road Driving .......................119 Oil (see Engine oil) .................. 160 Overdrive ................................... 110 P Panic alarm feature, remote entry system .................. 55 Park[...]

T ires ...........................140, 179–180 changing .......................... 140–141 checking the pressure ............ 180 replacing .................................. 182 rotating .................................... 181 snow tires and chains ............ 183 tire grades ............................... 180 treadwear ....................[...]

Item Information Required fuel Unleaded fuel only-87 octane. Fuel tank capacity- 2.0L I4 Zetec engine 57L (15 gallons) Fuel tank capacity- 3.0L V6 Duratec engine 61L (16 gallons) Engine oil capacity-2.0L I4 Zetec engine (includes filter change) 4.25L (4.5 quarts). Use SAE 5W -20 Super Premium Motor Oil. Engine oil capacity-3.0L V6 Duratec engine (i[...]