Mercury 1999 Mystique manuel d'utilisation

1 Contents Before driving Introduction 2 Instrumentation 4 Controls and features 20 Seating and safety restraints 72 Starting and driving Starting 104 Driving 1 12 Roadside emergencies 137 Servicing Maintenance and care 158 Capacities and specifications 217 Customer assistance 223 Reporting safety defects (U.S. only) 235 Index 236 11MCoen 4/13/99 2[...]

Introduction 2 ICONS Indicates a warning. Read the following section on W arnings for a full explanation. Indicates that vehicle information related to recycling and other environmental concerns will follow . W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication[...]

Introduction 3 INFORMA TION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. If possible, you should avoid hard braking for the first 1 600 km (1 000 miles). From 1 600 km (1 000 miles) onwards, you can gradually increase the per[...]

Page 22 Rear window defroster control* 4 Instrumentation Page 55 T urn signal/high beam Page 6 Instrument cluster Page 54 Hazard flasher control Page 56 W indshield wiper/washer control Page 162 Hood release Page 20, 21 Headlamp control/ Foglamp control* Page 54 Horn Page 53 T ilt steering wheel lever Page 52 Ignition switch Page 57 Speed control* [...]

5 Instrumentation On various models the appearance and location of some items may differ from those shown here. However , the page references given still apply . OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / POWER AUDIO AM/FM SCAN SEEK 3 1 2 4 5 ANS SIDE 1-2 EJECT VOLUME CLOCK Page 24 Climate control system Page 70 Anti-theft system statu[...]

Instrumentation 6 T urn signal Flashes when the left or right turn signal or hazard lights are activated. 0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MPH 20 40 60 55 80 120 10 0 140 160 18 0 200 10 0 EF 1 2 0 3 x 1 000 4 5 6 7 8 O/D OFF CHECK ENGINE BRAKE TRACTION CONTROL CH 0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MP[...]

Instrumentation 7 High beams Illuminates when the headlamp high beams are on. Charging system Briefly illuminates when the ignition is turned on and the engine is off. The light also illuminates when the battery is not charging properly and the vehicle may require electrical system service. O/D OFF TRACTION CONTROL Air bag secondary warning Flashes[...]

0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MPH 20 40 60 55 80 120 10 0 140 160 18 0 200 10 0 EF 1 2 0 3 x 1 000 4 5 6 7 8 O/D OFF CHECK ENGINE BRAKE TRACTION CONTROL CH Instrumentation 8 T raction control system light (if equipped) This light comes on when the traction control system has been disengaged. It may flash on and off while[...]

Instrumentation 9 O/D Off indicator (Automatic transaxle only) Illuminates and remains illuminated when the transaxle control switch (TCS) on the side of the gearshift lever is pressed and overdrive is turned off. For details, refer to the Driving chapter . Indicates the status of the transaxle and will flash steadily if a malfunction is detected. [...]

Instrumentation 10 Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics (OBD II) system. This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also [...]

Instrumentation 11 What you should do if the check engine light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. T emporary malfunctions may cause your check engine light to illuminate. Examples are: • The vehicle has run out of fuel (The engine may misfire or run poorly .) • Poor fuel quality or w[...]

Instrumentation 12 These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly tightening the fuel cap. After three drive cycles without these or any other temporary malfunctions present, the check engine light should turn off. (A driving cycle consists of a cold engine startup followed by mixed cit[...]

Instrumentation 13 CHECK ENGINE CHECK ENGINE Low fuel Illuminates when the fuel tank has approximately eight liters (two gallons) remaining. The lamp will also illuminate when the ignition key is turned to ON and the engine is off. CHECK ENGINE Air bag readiness Briefly illuminates when the ignition is turned on. If the light fails to illuminate, c[...]

Instrumentation 14 EF BRAKE O/D OFF 0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MPH 20 40 60 55 80 120 10 0 140 160 18 0 200 10 0 CHECK ENGINE TRACTION CONTROL CH 0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MPH 20 40 60 55 80 120 10 0 140 160 18 0 200 10 0 EF 1 2 0 3 x 1 000 4 5 6 7 8 O/D OFF CHECK ENGINE BRAKE TRACTION [...]

Instrumentation 15 Alternative design BRAKE BRAKE Anti-lock brake system (ABS) (if equipped) Momentarily illuminates when the ignition is turned on and the engine is off. If the light stays on or continues to flash, the ABS needs to be serviced. Brake system and ABS warning lights If both warning lights illuminate at the same time while driving, st[...]

Instrumentation 16 EF BRAKE O/D OFF 0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MPH 20 40 60 55 80 120 10 0 140 160 18 0 200 10 0 CHECK ENGINE TRACTION CONTROL CH 0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MPH 20 40 60 55 80 120 10 0 140 160 18 0 200 10 0 EF 1 2 0 3 x 1 000 4 5 6 7 8 O/D OFF CHECK ENGINE BRAKE TRACTION [...]

Instrumentation 17 Headlamps on warning chime Sounds when the headlamps are on, the ignition is off (and the key is not in the ignition) and the driver’ s door is open. Key-in-ignition warning chime Sounds when the key is left in the off/lock or accessory position and the driver’ s door is open. Safety belt warning chime For information on the [...]

Instrumentation 18 CH Engine coolant temperature gauge Indicates the temperature of the engine coolant. If it enters the red section, the engine is overheating. Switch off the ignition and determine the source of the problem. Refer to Checking and adding engine coolant in the Maintenance and care chapter . EF BRAKE TRACTION CONTROL O/D OFF 0001 23 [...]

Instrumentation 19 T rip odometer The trip odometer can register the mileage of individual journeys. T o reset, depress the button. 0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MPH 20 40 60 55 80 120 10 0 14 0 160 18 0 200 10 0 Speedometer Odometer T rip odometer Reset button EF Fuel gauge The fuel gauge displays the approximate level [...]

Controls and features 20 M I R R O R S OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / POWER AUDIO AM/FM SCAN SEEK 3 1 2 4 5 ANS SIDE 1-2 EJECT VOLUME 000123 0 0 0 0 10 20 30 40 50 60 70 80 90 10 0 110 120 13 0 MPH 20 40 60 55 80 120 100 140 160 180 200 EF 1 2 0 3 x 1000 4 5 6 7 8 BRAKE CHECK ENGINE O/D OFF TRACTION CONTROL CLOCK CH INSTRUM[...]

Controls and features 21 Daytime running light (DRL) (Canadian vehicles only) The DRL system turns on the highbeam headlamps, with a reduced light output, when: • the vehicle is running and the ignition is in the on position and • the headlamp system is in the off position. Foglamp control (if equipped) Pull out the control while the headlamps [...]

Controls and features 22 Rear window defroster (if equipped) Press the defroster control to clear the rear window of thin ice and fog. The ignition must be in the on position to operate the rear window defroster . The defroster turns off automatically after 10 minutes or when the ignition is turned to the off position. T o manually turn off the def[...]

Controls and features 23 Panel dimmer control Adjust the control to vary the intensity of the panel lighting. Operates only when the exterior lights are switched on. T o switch on the interior lamp, rotate the control completely to the left. Power mirrors The control can be swivelled and turned. T urn the control counterclockwise to adjust the driv[...]

Controls and features 24 OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / POWER AUDIO AM/FM SCAN SEEK 3 1 2 4 5 ANS SIDE 1-2 EJECT VOLUME 000123 0000 10 20 30 40 50 60 70 80 90 10 0 110 120 13 0 MPH 20 40 60 55 80 120 100 140 160 180 200 EF 1 2 0 3 x 1000 4 5 6 7 8 CHECK ENGINE TRACTION CONTROL O/D OFF M I R R O R S CLOCK TRACTION ROL CH Cli[...]

Controls and features 25 Heater only system (if equipped) OFF LO PNL/FLR PANEL FLOOR DEF FLR DEF HI / LO HI T emperature control knob Controls the temperature of the airflow inside the vehicle. On heater -only systems, the air cannot be cooled below the outside temperature. Mode selector control Controls the direction of the airflow to the inside o[...]

Controls and features 26 • FLR/DEF – Distributes outside air through the floor ducts and the windshield defroster ducts. • DEF – Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. Operating tips • In humid weather , select DEF before driving. This will help to prevent yo[...]

Controls and features 27 Manual heating and air conditioning system (if equipped) OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / LO HI Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. OFF PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C [...]

Controls and features 28 Under normal conditions, your vehicle’ s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. • MAX A/C – Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more e[...]

Controls and features 29 • PNL/FLR – Distributes outside air through the instrument panel registers and the floor ducts. However , the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot [...]

Controls and features 30 • DEF – Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 10°C (50°F) or higher , the air conditioner will automatically dehumidify the air to prevent fogging. Operating tips • In humid weather , select DEF before drivi[...]

Controls and features 31 Cabin air filter Y our vehicle is equipped with an air filter that removes pollen and road dust from outside air before it is directed to the interior of the vehicle. Refer to the Maintenance and care chapter for maintenance of this filter . • When placing objects on top of your instrument panel, be careful to not place t[...]

Controls and features 32 M I R R O R S OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / POWER AUDIO AM/FM SCAN SEEK 3 1 2 4 5 ANS SIDE 1-2 EJECT VOLUME 000123 0 0 0 0 10 20 30 40 50 60 70 80 90 10 0 110 120 13 0 MPH 20 40 60 55 80 120 100 140 160 180 200 EF 1 2 0 3 x 1000 4 5 6 7 8 CHECK ENGINE TRACTION CONTROL O/D OFF CLOCK TRACTION TROL CH[...]

Controls and features 33 Electronic stereo radio with cassette Electronic stereo radio 13MCten 4/13/99 3:35 PM Page 33[...]

Controls and features 34 SIDE 1-2 13MCten 4/13/99 3:35 PM Page 34[...]

Controls and features 35 SIDE 1-2 1-2 SIDE 13MCten 4/13/99 3:35 PM Page 35[...]

Controls and features 36 Power control Press the control to turn the audio system on or off. V olume control Press the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select T[...]

Controls and features 37 The tune adjust with electronic stereo radio • Press (–) to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press (+) to move to the next frequency up the band (whether or not a listenable station is located t[...]

Controls and features 38 • W ithin approximately five seconds, press and release either or on the SEEK control to change to the next frequency up or down. • Press and hold down or to quickly move through the frequencies. Seek function The seek function control works in radio or tape mode. Seek function in radio mode • Press to find the next l[...]

Controls and features 39 Scan function The scan function works in radio and CD mode (if equipped). Scan function with electronic stereo cassette radio Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function with compact disc radio • Press the SC[...]

Controls and features 40 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. If the battery is disconnected, the memory preset stations will need to be reset. Automatic memory store (if equipped) Automatic memory store allows you to set strong radio stations withou[...]

Controls and features 41 2. Press the AUTO PRESET control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. Deactivating[...]

Controls and features 42 • Press (+) or (–) on the volume control to increase or decrease treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. T reble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. • Push the AUDIO contro[...]

Controls and features 43 Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers. • Push the AUDIO control repeatedly until the display reads F ADE. • Press the (+) side of the volume control to shift sound to the front speakers. • Press the (–) side of the volume control to shift sound to the rear[...]

Controls and features 44 Setting the clock Press and hold CLOCK, then press SEEK to increase the hours or to increase minutes. The clock will display 12-hour time with no AM/PM indications. On the single CD audio system, the clock can be set with the radio power on or off. T ape play select Insert a tape to begin tape play . Push only slightly when[...]

Controls and features 45 Rewind/fast forward in CD mode • Press the control for less than three seconds for slow rewind. • Press the control for more than three seconds for fast rewind. • Press the control for less than three seconds for slow forward action. • Press the control for more than three seconds for fast forward action. T ape dire[...]

Controls and features 46 CD eject Press the control to stop and eject a CD. If a disc is ejected from the CD player but is not removed within approximately 10 seconds, the player will automatically reload the disc for storage (unless the disc is automatically ejected because it was inserted upside down, in which case the disc will not be automatica[...]

Controls and features 47 DISPLA Y SCREEN The display screen gives information on the status of the audio system. Display Information AM, FM1 or FM2 Indicates which frequency band the audio system is in 87.9 to 107.9 Indicates currently playing radio station (530 to 1610 Am) Illuminated bars Indicates volume, relative levels of bass and treble and r[...]

Controls and features 48 T roubleshooting the CD Player The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • Y ou may be travelling on a rough road, playing scratched discs or the disc may be dirty . Skipping will not scratch the discs or damage the player . If player doe[...]

Controls and features 49 CD and CD player care • Handle discs by their edges only . Never touch the playing surface. • Do not insert more than one disc at a time. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • After playing, store the disc in its case. Cleaning cassette player (if equipped) Clean th[...]

Controls and features 50 • Remove loose labels before inserting tapes. • Do not leave tapes in the cassette player for a long time when not being played. RADIO FREQUENCY INFORMA TION The Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Communications (CRTC) establish the frequencies AM and FM stations may u[...]

Controls and features 51 • T errain. Hills, mountains and tall buildings between your vehicle’ s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns [...]

Controls and features 52 STEERING COLUMN CONTROLS Ignition 1. Ignition off, steering wheel locked. On vehicles with automatic transaxles, the ignition key can return to this position only if the gearshift lever is in P (Park). 2. The accessory position. Steering unlocked, radio operational. Ignition and all main electrical circuits are disabled. Th[...]

Controls and features 53 OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / POWER AUDIO AM/FM SCAN SEEK 3 1 2 4 5 ANS SIDE 1-2 EJECT VOLUME 000123 0 0 0 0 10 20 30 40 50 60 70 80 90 10 0 110 120 13 0 MPH 20 40 60 55 80 120 100 140 160 180 200 EF 1 2 0 3 x 1000 4 5 6 7 8 CHECK ENGINE TRACTION CONTROL O/D OFF M I R R O R S CLOCK TRACTION TROL CH[...]

Controls and features 54 Hazard flasher control Use only in an emergency to warn traffic of vehicle breakdown or approaching danger . Depress to activate. Depress again to switch off. The hazard lights can be operated when the ignition is off. Off Res Set Acc Coast On Off Res Set Acc Coast On Horn Press the pad. The horn can be operated when the ig[...]

Controls and features 55 OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / POWER AUDIO AM/FM SCAN SEEK 3 1 2 4 5 ANS SIDE 1-2 EJECT VOLUME 000123 0 0 0 0 10 20 30 40 50 60 70 80 90 10 0 110 120 13 0 MPH 20 40 60 55 80 120 100 140 160 180 200 EF 1 2 0 3 x 1000 4 5 6 7 8 CHECK ENGINE TRACTION CONTROL O/D OFF M I R R O R S CLOCK TRACTION TROL CH[...]

Controls and features 56 Wipers Lift the windshield wiper lever to the desired speed interval. • Intermittent: push lever up to the first position. • Low: push lever up to the second position. • High: push lever up to the third position. For a single wipe, push the lever downward. Windshield wipers and washer Intermittent wiper control (if eq[...]

Controls and features 57 Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. Off On Speed control (if equipped) T o turn speed control off • Press Off, or • turn off the vehicle ignition. Once the speed control is switched off, the previously programmed set speed will be erased. T o turn speed cont[...]

Controls and features 58 T o set a speed Press Set Acc. For speed control to operate, the speed control must be on and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle spe[...]

Controls and features 59 Res Set Acc Coast T o set a lower speed • Press and hold Coast. Release the control when the desired vehicle speed is reached, or • press and release Coast. Each press will decrease the set speed by 1.6 km/h (1 mph), or • depress the brake pedal. When the desired vehicle speed is reached, press Set Acc. T o set a high[...]

Controls and features 60 Res Set Acc Coast T o return to a set speed • Press Res. For Res to operate, the vehicle speed must be faster than 48 km/h (30 mph). T o disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. OVERHEAD CONTROLS Interior lamps with reading lamps[...]

Controls and features 61 12 SEC On Off 12 SEC Interior lamps (sunroof equipped vehicles) The reading lamps are operated by separate on/off switches and can be adjusted to point in the desired direction. Open/Lift Close Sunroof (if equipped) The electric sunroof can be operated only when the ignition is switched on. T o open and close the sunroof Pr[...]

Controls and features 62 Power door locks (if equipped) Push to lock or unlock all doors. Power windows (if equipped) The windows will only operate when the ignition is switched on. Press the appropriate control to operate the power windows at each door position. All of the windows can be controlled from the control on the driver door . The passeng[...]

Controls and features 63 Safety switch Move the switch to the left to prevent passengers from operating the windows. Move the switch to the right to allow passengers to operate the windows. CHILD LOCK BELOW SECURITE ENFANTS CI-DESSOUS ´ VERROUILLEE , LOCKED WHEN LOCKED, DOOR WON`T OPEN FROM INSIDE. ´ VERROULEE AINSI, LA PORTE NE PEUT S´OUVRIR DE[...]

Controls and features 64 PULL Remote luggage compartment control Pull the control located on the left of the driver seat to open the luggage compartment. FLOOR MOUNTED CONTROLS Parking brake For information on the parking brake, refer to Preparing to start the vehicle in the Starting chapter . 13MCten 4/13/99 3:36 PM Page 64[...]

Controls and features 65 Fuel pump shut-off switch For information on the fuel pump shut-off switch, refer to Fuel pump shut-off switch in the Roadside emergencies chapter . Positive retention floor mat Position the floor mat in the footwell. Place the mat eyelet over the pointed end of the retention post from the rear and rotate forward to install[...]

Controls and features 66 TRUNK UN LOCK PANIC LOCK REMOTE KEYLESS ENTR Y SYSTEM (if equipped) If your vehicle has a remote entry system, you can lock and unlock the vehicle doors and open the luggage compartment without using a key . The remote also has a personal alarm feature. The remote entry feature only operates with the ignition in the off pos[...]

Controls and features 67 Opening the luggage compartment Press the TRUNK control. Sounding the panic alarm Press the P ANIC control. The horn will sound and the headlamps and tail lamps will flash for approximately 2 minutes and 45 seconds. T o deactivate the alarm, press the P ANIC control again or turn the ignition key to the on position. UN LOCK[...]

Controls and features 68 Replacing lost transmitters T ake your transmitters to the dealer for reprogramming if: • a transmitter is lost, or • you want to purchase additional transmitters. This device complies with part 15 of the FCC rules. Operation is subject to the two following conditions: (1) The device may not cause harmful interference, [...]

Controls and features 69 P ASSIVE ANTI-THEFT SYSTEM (if equipped) The Passive Anti-Theft system (P A TS) is an engine immobilization system. It is an additional theft protection feature that prevents the engine from being started unless a coded key is used.. This system is only available with 2.5 litre engines. OFF LO PNL/FLR PANEL A/C FLOOR DEF FL[...]

Controls and features 70 Functional check When the ignition is switched on, the control light will illuminate for approximately three seconds to indicate that the system is operating correctly . If the control light flashes rapidly for approximately one minute and then repeatedly at irregular intervals, the system did not recognize the key code. Re[...]

Controls and features 71 Spare key programming A maximum of 8 keys in all can be coded with any two coded keys. • Insert the first key in the ignition switch and turn to position 3. • T urn the key back to position 1 and remove from the ignition switch within 5 seconds. • Insert the second key in the ignition switch and turn to position 3 wit[...]

72 Push or pull the head restraint to the desired height. SEA TING Manually adjusting the seats Pull the lever located at the front edge of the seat to move the seat forward or backward. Reclining the seats Pull the lever on the outside of the seat to recline the seat. Never adjust the driver seat or seat back when the vehicle is moving.[...]

73 respective direction to adjust the seat as follows: 1 2 3 4 Seat (1) Forward and backward (2) Height of the entire seat (3) Height of the front of the seat (4) Height of the rear of the seat Lumbar support Pull the lever to adjust lumbar support.[...]

74 the seat. The seat back cannot be released while the built-in child seat (if equipped) is open. If you are carrying objects that might damage the center rear three-point safety belt, you can unbuckle the end of the belt from the small buckle on the seat cushion and let the retractor reel it up. Reconnect the belt tongue to the buckle when you fo[...]

75 The use of safety belts helps to restrain both driver and passenger in case of a collision. In most states and Canada, the law requires the use of safety belts. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lock the doors of your vehicle before driving to lessen the risk of the door coming open i[...]

76 Insert the tongue into the slot in the buckle to fasten. Push the red release button and remove the tongue from the slot to unfasten. The passenger safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger safety belts have two types of locking modes. Each seating position in your vehicle has a sp[...]

77 Automatic locking mode In this mode, the shoulder belt is automatically prelocked; however , the belt will react to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver’ s safety belt. When to use the automatic locking mode • When a tight lap and shoulder belt fit is desired. • Any time a child s[...]

78 Canceling automatic locking mode Disconnect the combination lap and shoulder belt and allow it to completely retract. This will cancel the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. safety seat in any passenger seat. 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder belt portion and p[...]

79 T o lower the height of the shoulder belt: 1. Push the control down. 2. Slide down. T o raise the height of the shoulder belt: 1. Slide up. 2. Pull down on the height adjuster to make sure that it is locked in place. height adjuster so that the belt rests across the middle of your shoulder . Be sure the shoulder belt is properly positioned on yo[...]

80 Safety belt indicator light and warning chime Illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. been unbuckled, pull the belt steadily from the reel and insert the small tongue into the small buckle until a distinct “click” is heard. This buckle should be left buckled except when t[...]

81 Safety belt extension assembly The safety belt may be too short even when fully extended. Approximately 20 cm (8 inches) may be added to the length of the belt with a safety belt extension (part number 611C22). Safety belt extensions are available at no cost from your dealer . Only use extensions manufactured by the same supplier as the safety b[...]

82 security of the anchorage points and the locking action of the inertia reels by giving each belt a sharp tug. Belts subjected to strain, as in the result of an accident, should be replaced and the anchorages checked by your dealer or a qualified technician. Failure to follow these instructions will affect the performance of the safety belts and [...]

83 Important supplemental restraint system (SRS) precautions The supplemental restraint system (SRS) is designed to: • work with the safety belt to protect the driver and right front passenger . • reduce certain upper body injuries. AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) M I R R O R S OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI [...]

84 When installing forward- facing child seats in the front seat always move the passenger seat as far back from the instrument panel as possible. Never install rear -facing child seats or rear -facing infant seats in the front seat. Children and air bags For additional important safety information, read all information on safety restraints in this[...]

85 The SRS is designed to activate when the vehicle is in a collision, similar to hitting a fixed barrier head-on at 12-24 km/h (8-14 mph). The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activation. The air bags in[...]

86 The SRS consists of the following: • driver and passenger air bag modules (which include the inflators and air bags), • one impact and one safing sensor , • a readiness light and secondary warning light, and • the electrical wiring and components. The diagnostic module monitors its own internal circuits and the supplemental air bag elect[...]

87 the instrument cluster or a secondary warning light to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter . Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. [...]

88 equipped vehicles, see your local dealership or a qualified technician. Air bags MUST BE disposed of by qualified personnel. Res Coast Set Acc Off On[...]

89 It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safe[...]

90 safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are 4 years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or provincial laws for specific requirements regarding the safety of chi[...]

91 child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraints and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’ s face or neck, the child s[...]

92 positioning booster seat that is labelled as conforming to all federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter , firmer seating posture and better fit of lap and shoulder belts on the child. A belt-positioning booster seat should be used if the shoulder belt rests in front of the child[...]

93 All built-in child restraints, including seats, buckles, retractors, seat latches, interlocks, and attaching hardware should be inspected by a qualified dealer technician after any collision. The rear seat may include a built-in child seat. This child seat conforms to all federal and local motor vehicle safety standards. Read the labels located [...]

94 Built-in child seat retractors The belts on built-in child seats are equipped with a retractor . The retractor will automatically snug the belts around the child. If the belts do not remain snug, take the vehicle to your dealer or a qualified technician for child seat repair . The belts will not remain snug during a collision if the retractor is[...]

95 1. Make sure that the seatback is securely latched in place. 2. Grasp the child seat cushion and pull the top forward to release the latch. Continue to unfold the child seat until it rests on the seat in the fully open position. instructions on the use of this child restraint system can result in your child striking the vehicle’ s interior dur[...]

96 4. If connected, squeeze the tabs on the top and bottom of the chest clip and pull the halves apart to open the chest clip. Then release the lower half of belt by pressing the red button. 5. Place the child in the child seat and position the shoulder belts over each shoulder . child seat.[...]

97 If both tongues do not latch in the buckle, do not use the child seat. See your dealer for repairs. 7. Fasten both halves of the chest clip below the child’ s shoulders and adjust it to comfortably hold the shoulder belts in place on the child’ s chest. The color green must appear in the indicator window when fastened. 8. Pull the lap portio[...]

98 T o stow the built-in child seat Return the child seat cushion to the upright position, then press firmly in the center and top of the child seat. Inspecting the built-in child seat after a collision All built-in child restraints, including seats, buckles, retractors, seat latches, interlocks and attaching hardware should be inspected by your de[...]

99 included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or collision. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For[...]

100 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sur[...]

101 5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the [...]

102 seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10. T ry to pull the belt out of the retractor to make sure the retractor is in automatic locking mode (you should not be able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Check to make s[...]

103 tether hook into the hole in the tongue of the center rear lap belt. After the hook is in the hole, pull on the loose end of the lap belt webbing to shorten the belt and tighten the tether strap. T o install a tethered child safety seat in the rear seat, you will need tether anchor hardware. T ether anchor hardware T ether anchor hardware kits [...]

Starting 104 Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. IMPORT ANT SAFETY PRECAUTIONS A computer system controls the engine’ s idle revolutions per minute (rpm). When the engine starts, the idle rpm runs faster to warm the engine. If the eng[...]

Starting 105 IMPORT ANT VENTILA TION INFORMA TION If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (1 inch). OFF PLN/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C Adjust the heating or air conditioning to bring in fresh air . Do not start your vehicle in a closed garage or in [...]

Starting 106 Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves, and other debris. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. Have the exhaust and body ventilation system checked whenever: • the vehicl[...]

Starting 107 PREP ARING TO ST ART THE VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference- Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator pedal before or during st[...]

Starting 108 If starting a vehicle with a manual transaxle: • Make sure the parking brake is set. • Push the clutch pedal to the floor . Otherwise, the engine will not crank (turn over). • Put the gearshift into neutral. If starting a vehicle with an automatic transaxle: • Make sure the parking brake is set. • Make sure the gearshift is i[...]

Starting 109 3. T urn the key to the on position (without turning the key to start). Make sure the following lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced by your dealer or a qualified service technician. • If the driver’ s safety belt is fastened the safety belt warning light does not illuminate. BRAKE B[...]

Starting 110 ST ARTING THE ENGINE 1. T urn the key to the start position (4) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to the on (3) position. 3 4 2 1 2. If the engine does not start within five seconds, wait ten seconds and try again. 3. If the engine does not start in two attempts OR the [...]

Starting 111 USING THE ENGINE BLOCK HEA TER (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater - defroster system to respond quickly . It is strongly recommended if you live in a region where temperatures reach –23°C (–10°F) or below . For best results, plug[...]

Driving 112 BRAKES Y our brakes are self-adjusting. Refer to the “Scheduled Maintenance Guide” for maintenance intervals. Anti-lock braking system (ABS) (if equipped) The ABS operates by detecting the onset of wheel lock-up during brake applications and compensating for this tendency . The wheels are prevented from locking even when the brakes [...]

Driving 113 T wo important rules when braking in emergencies with ABS: 1. Apply full force on both brake and clutch pedal (if equipped). Braking with ABS • In an emergency , apply full force on the brake pedal. In vehicles with manual transaxles, you must also depress the clutch pedal. The anti-lock braking system will be activated immediately , [...]

Driving 114 Parking brake T o engage the parking brake: Pull the handle upward. T o release the parking brake: 1. Press and hold the release button. 2. Push handle downward to the off position. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transaxle) or in 1 (first) (manual transaxle)[...]

Driving 115 TRACTION CONTROL (if equipped) This system prevents wheel spin at all speeds. The control will toggle this function on and off, but the feature defaults to on after each cycle of the ignition key . The traction control system controls excessive wheel spin by automatically applying and releasing the brakes in conjunction with engine torq[...]

Driving 116 STEERING YOUR VEHICLE Y our vehicle comes with power steering. Power steering uses energy from the engine to help steer your vehicle. If the amount of effort needed to steer your vehicle at a constant vehicle speed, have the power steering system checked. If the power steering system breaks down (or if the engine is turned off), you can[...]

Driving 117 TRANSAXLE OPERA TION Automatic transaxle (if equipped) V ehicles equipped with an automatic transaxle are equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from the P (Park) position unless the brake pedal is depressed. Putting your vehicle in gear Y ou must push the thumb button to move th[...]

Driving 118 Overriding the brake-shift interlock feature If it is necessary to use this procedure to move the gearshift lever , it is possible that a fuse has blown and the vehicle’ s brakelamps may not be working. Refer to Fuses and relays in the Roadside emergencies chapter . If you cannot move the gearshift lever from P (Park) with the brake p[...]

Driving 119 •P (Park) Always come to a complete stop before shifting into P (Park). This locks the transaxle and prevents the front wheels from rotating. • R (Reverse) The vehicle only moves backward. Always come to a complete stop before shifting in or out of R (Reverse). P = Park . . . . . . . . . . . . . . R = Reverse . . . . . . . . . . . N[...]

Driving 120 • D (Overdrive) Note that the vehicle’ s gearshift is console-mounted on the floor . The transaxle control switch (TCS) is located on the gearshift handle. The transaxle control indicator light (O/D light) is located on the instrument panel. Overdrive is not shown on the display , but is the default mode for the D gearshift position[...]

Driving 121 O/D OFF TRACTION CONTROL • D (Drive) D (Drive) provides more engine braking than overdrive and is useful when driving through hilly terrain or if your vehicle requires additional power for climbing hills. Activate by pressing the transaxle control switch (TCS) located on the gearshift handle. The O/D OFF indicator light will illuminat[...]

Driving 122 • 1 (First) Use the 1 (First) position to provide maximum engine braking on steep downgrades. Upshifts will not occur while the gearshift lever remains in the 1 (First) position. Upshifts may be made by shifting to the 2 (second) position or to D (Drive). Selecting the 1 (First) position at high speeds causes the transaxle to downshif[...]

Driving 123 Manual transaxle (if equipped) V ehicles equipped with a manual transaxle have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. Using the clutch When starting a vehicle with a manual transaxle: 1. Hold down the brake pedal. 2. Depress the clutch pedal. 3. Put the gearshift lever in neutra[...]

Driving 124 *The vehicle can be shifted at lower speeds to improve fuel economy . 22 Recommended shift speeds 2.0 litre engine 5-speed transaxle shift speed schedules Recommended upshifts: Shift from km/h mph 14 25 33 48 40 53 77 mph 12 20 29 40 km/h 19 32 64 First to second Second to third Third to fourth Fourth to fifth During acceleration: Durin[...]

Driving 125 Parking 1. Apply the brake and the clutch and shift into neutral. 2. Engage the parking brake. 3. Shift into 1 (First) or R (Reverse). 4. T urn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (first) gear and set the parking brake. Reverse T o shift into R (Reverse): 1. Completel[...]

Driving 126 LOADING YOUR VEHICLE Before loading your vehicle, familiarize yourself with these terms. GVW (Gross V ehicle Weight) Base curb weight plus the payload weight. The GVW is not a limit or a specification. Payload Combined maximum allowable weight of passengers, cargo and optional equipment. Base curb weight W eight of the vehicle including[...]

Driving 127 GCW (Gross Combined Weight) The GCW is the maximum combined weight of the towing vehicle (including passengers and cargo) and the loaded trailer . The GCW is specified by the manufacturer to indicate the combined maximum loaded weight that the vehicle is designed to tow . GA WR (Gross Axle Weight Rating) Carrying capacity for each axle [...]

Driving 128 -9% -6% -3% 900 m (3000 ft) 600 m (2000 ft) 300 m (1000 ft) 0 Payload = GVWR minus Base curb weight T o obtain the correct weight for your vehicle, try taking your vehicle to a shipping company or an inspection station for trucks. Do not use replacement tires with lower weight capacities than the originals because they might lower the v[...]

Driving 129 It is extremly dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and usin[...]

Driving 130 TRAILER TOWING Y our vehicle is capable of towing a trailer of up to a maximum of 454 kg (1 000 lbs) gross trailer weight with a maximum tongue load of 45 kg (100 lbs). It should also have 2.3 sq. meters (25 sq. feet) or less frontal area. Do not drive faster than 72 km/h (45 mph) while towing a 454 kg (1 000 lb) trailer . Y our vehicle[...]

Driving 131 Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’ s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter . • Use extra caution when driving while trailer towing. Refer to Driving while towing a trailer in this chapter . • Service your vehicle mo[...]

Driving 132 Preparing to tow Use the proper equipment for towing a trailer and make sure that it is properly attached to your vehicle. See your dealer or a reliable trailer retailer if you require assistance. Auxiliary coolers are recommended for the power steering system and automatic transaxle system if you are planning on: • T raveling farther[...]

Driving 133 Using a hitch Do not use hitches that: • Clamp onto the vehicle bumper . • Attach to the axle. Distribute the load so that only 10 to 15% of the total weight of the trailer is on the tongue. T ie down the load so that it does not shift and change weight on the hitch. Follow the instructions of a reputable rental agency . Using trail[...]

Driving 134 Using safety chains Always connect the trailer’ s safety chains to the vehicle. T o connect the chains, cross the chains under the trailer tongue and attach to the vehicle frame or hook retainers (not the bumper). Make sure there is enough slack to allow the vehicle to turn corners. Do not connect a trailer’ s hydraulic brake system[...]

Driving 135 Driving while towing a trailer Do not drive faster than 72 km/h (45 mph) while towing a 454 kg (1 000 lb) trailer . Do not drive faster than 72 km/h (45 mph) with any weight trailer while towing in hilly terrain or on hot days. Speed control (if equipped) may not work properly while towing on long, steep grades. If driving with an autom[...]

Driving 136 FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular , scheduled maintenance, • excessive speed, • rapid acceleration, • driving with the brake pedal depressed, • sudden stops, • extended engine idling, • use of speed control in hilly terrain, • extended use of the air conditioner , defroster , re[...]

Roadside emergencies 137 HAZARD FLASHER CONTROL Use only in an emergency to warn traffic of vehicle breakdown or approaching danger . Depress to activate. Depress again to switch off. The hazard lights can be operated when the ignition is off. Off Res Set Acc Coast On FUEL PUMP SHUT -OFF SWITCH If the engine cranks, but does not start or does not s[...]

Roadside emergencies 138 If your engine cranks but does not start after a collision or substantial jolt: 1. T urn the ignition key to the off position. 2. Check under the vehicle for leaking fuel. 3. If you do not see or smell fuel, push the red reset button down. If the button is already set, you may have a different mechanical problem. 4. T urn t[...]

Roadside emergencies 139 Even after a fuse is replaced, it will continue to blow if the cause of the overload is not identified and corrected. If the fuse continues to blow , have the vehicle’ s electrical system checked by your dealer or a qualified service technician. T o reset a circuit breaker press the reset button. The passenger compartment[...]

Roadside emergencies 140 1 Power distribution box T o check or replace a fuse or a relay , remove the cover of the fuse box in the engine compartment by releasing the latch (1) and lifting up. A blown fuse can be identified by a break in the wire. All fuses are a push fit. Five reserve fuses with different current ratings are attached to the inside[...]

Roadside emergencies 141 Ampere rating Circuits protected 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 39 40 41 42 43 44 45 46 47 48 49 50 51 52 — 7.5 20 — — 3 20 — 15 — 20 — 20 7.5 7.5 7.5 7.5 7.5 — 20* 20* 40* — — 60* — — — 60* — 60* 60* Not used Alternator Foglamps Not used Not used EEC ignition module (memory) Horn and[...]

Roadside emergencies 142 Passenger compartment fuse panel T o check or change a fuse or a relay , open the fuse box by pulling down the lock release lever (1). 1 Power distribution box (engine compartment) Relay Circuits switched R 1 R 2 R 3 R 4 R 5 R 6 R 7 R 8 R 9 R 10 R 11 D1 D2 Fuel pump EEC module Air conditioning Low beam High beam Horn Starte[...]

Roadside emergencies 143 A blown fuse can be identified by a break in the wire. All fuses are a push fit. Five reserve fuses with different current ratings are attached to the inside cover of the power distribution box in case of emergency fuse replacement. 19 20 21 R16 R15 R14 R12 R13 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 D2 Passenger[...]

Roadside emergencies 144 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 — C10 40 7.5 15 15 20 7.5 15 30 30 7.5 7.5 7.5 7.5 7.5 7.5 — 30 — Not used W iper motors (circuit breaker) Power windows ABS module Backup lamps Brake lamps Door locks Main light Cigar lighter Electric seats Rear window defrost Engine management system Instru[...]

Roadside emergencies Fuse rating 7.5 amp 10 amp 15 amp 20 amp 30 amp 30 amp fuse link 40 amp 60 amp fuse link 80 amp fuse link 100 amp fuse link Color brown red light blue yellow light green pink orange yellow black blue Relay R 18 R 20 R 21 R 22 R 23 R 24 R 25 R 26 “One touch” switch (driver’ s window) Not used Not used Foglamps T urn signal[...]

Roadside emergencies 146 CHANGING TIRES Park your vehicle in such a position that neither the traffic nor you are hindered or endangered when changing the tire. Ensure that the vehicle is on firm, level ground. Secure your vehicle further by blocking the wheels. Activate the hazard lights. Apply the parking brake and engage first or reverse gear if[...]

Roadside emergencies 147 80 MAX km/h When driving with a temporary spare tire: • Do not exceed the maximum speed of 80 km/h (50 mph) and only drive the shortest possible distance. • Do not exceed the permissible gross weight of the vehicle. • Do not install more than one spare wheel on your vehicle at any one time. • Do not use snow chains [...]

Roadside emergencies 148 Removing a tire 1. Apply the parking brake and 1 (first) gear (manual transaxle) or the P (Park) position (automatic transaxle). 2. Activate the hazard flashers. 3. The driver and all passengers must leave the vehicle. 4. Secure the vehicle against rolling or sliding. 5. Insert the tapered end of the jack handle between the[...]

Roadside emergencies 149 Replacing a tire 1. Push the spare tire onto the wheel studs. 2. Screw on the wheel nuts, ensuring the tapered end of the wheel nuts are facing the wheel, and secure in a clockwise direction. 3. Lower the vehicle and remove the jack by turning the handle counterclockwise. 4. Fully tighten the wheel nuts in a crosswise patte[...]

Roadside emergencies 150 JUMP ST ARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which burns skin, eyes, and clothing if cont[...]

Roadside emergencies 151 3. Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ens[...]

Roadside emergencies 152 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from th[...]

Roadside emergencies 153 Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery . • 2.0 litre engine • 2.5 litre engine 23MREen 4/13/99 3:42 PM Page 153[...]

Roadside emergencies 154 5. Be sure that the cables are clear of fan blades, belts and other moving parts of both engines. Jump starting 1. Start the engine of the booster vehicle and run the engine at a moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for a fur[...]

Roadside emergencies 155 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery After the disabled vehicle has been st[...]

Roadside emergencies 156 If towing is necessary , it is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a T -hook or slingbelt towing procedure. WRECKER TOWING 23MREen 4/13/99 3:42 PM Page 156[...]

Roadside emergencies 157 Never use a tow bar that attaches to the bumper when you tow your vehicle. This could damage the bumper and cause an accident. TOWING YOUR VEHICLE BEHIND ANOTHER VEHICLE Before you have your vehicle towed: • release the parking brake, • move the gearshift to N (Neutral), • turn the ignition to the off position and •[...]

Maintenance and care 158 SERVICE RECOMMENDA TIONS • W e highlight do-it-yourself items in the engine compartment for easy location. • As possible, we design parts that can be replaced without tools. • W e provide you with a maintenance guide and or service guide which makes tracking routine service for your vehicle easy . If your vehicle requ[...]

Maintenance and care 159 Precautions when servicing your vehicle Be especially careful when inspecting or servicing your vehicle. Here are some general precautions for your safety: • Do not work on a hot engine. The cooling fan is automatic and may come on at any time. Always disconnect the negative terminal of the battery before working near the[...]

Maintenance and care 160 Working with engine off (manual transaxle) 1. Set the parking brake, depress the clutch and place the gearshift in 1 (first) or R (Reverse). 2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly . Working with engine off (automatic transaxle) 1. Set the parking brak[...]

Maintenance and care 161 Working with engine on (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly . Working with engine on (manual transaxle) 1. Set the parking brake, depress the clutch and place the gearshift in neutral[...]

Maintenance and care 162 Opening the hood • Pull the handle (1) located under the instrument panel. 000123 0 0 0 0 10 20 30 40 50 60 70 80 90 10 0 110 120 130 MPH 20 40 60 55 80 120 100 140 160 180 200 EF 1 2 0 3 x 1000 4 5 6 7 8 CHECK ENGINE TRACTION CONTROL O/D OFF M I R R O R S 1 TRACTION TROL CH • Release the safety catch by reaching under [...]

Maintenance and care 163 For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black. 2.0 litre EFI-engine compartment Power steering reservoir Engine coolant reservoir Automatic transaxle dipstick (if equipped) Brake fluid reservoir Battery W indshield washer fluid reservoir Engine oil dipstick Power distributio[...]

Maintenance and care 164 Power steering reservoir Engine coolant reservoir 2.5 litre EFI-engine compartment For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black. Air cleaner Brake fluid reservoir Automatic transaxle dipstick (if equipped) Battery W indshield washer fluid reservoir Engine oil dipstick Power[...]

Maintenance and care 165 ADD FULL Engine oil Use SAE 5W -30 motor oil CERTIFIED FOR GASOLINE ENGINES by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by Ford W arranty . Checking[...]

Maintenance and care 166 6. If the oil level is below the minimum line, add engine oil as necessary . If the oil level is beyond the maximum line, engine damage or high oil consumption may occur and some oil must be removed from the engine by a service technician. 7. Put the dipstick back in and ensure it is fully seated. Continuous contact with us[...]

Maintenance and care 167 Empty and used oil containers must be disposed of at an authorized waste disposal facility . Engine oil filler cap The design of the filler cap varies by engine. T o open, turn in the direction of the arrow and pull. Do not open the cap while the engine is running. Refer to the maintenance guide and or service guide for add[...]

Maintenance and care 168 Brake/clutch fluid reservoir Brake and clutch fluid systems are supplied from the same reservoir . The level of the fluid must lie between the MIN and MAX marks on the side of the reservoir . If the level falls below the MIN mark, the brake fluid level warning light on the instrument cluster will illuminate. Add only DOT 3,[...]

Maintenance and care 169 Engine coolant maintenance MAX MIN Checking and adding engine coolant Check the level of the coolant in the reservoir at least once a month. Be sure to read and understand Precautions when servicing your vehicle in this chapter . If the engine coolant has not been checked for a long period of time, the engine coolant reserv[...]

Maintenance and care 170 When adding engine coolant Ford recommends Ford Premium Cooling System Fluid, which is an optimized formula that will protect all metals and rubber elastomers used in Ford engines for four years or 80 000 km (50 000 miles). It is neither necessary nor recommended to use supplemental coolant additives in your gasoline- power[...]

Maintenance and care 171 Always dispose of used automotive fluids in a responsible manner . Follow your community’ s standards for recycling and disposing of automotive fluids. Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolan[...]

Maintenance and care 172 MAX MIN Adding engine coolant 1. Before removing the engine coolant recovery cap, turn the engine off and allow it to cool. 2. When the engine is cool, turn and remove the cap. • Step back for a moment while the pressure in the reservoir is released. • Stand away from the reservoir opening. Hot steam or coolant spray ma[...]

Maintenance and care 173 Checking and adding power steering fluid Switch off the engine. W ith the steering system at normal operating temperature, the fluid level should come up to the MAX mark. If the fluid level drops below the MIN mark, add the specified fluid. Refer to the Capacities and specifications chapter . Severe winter climate If you dr[...]

Maintenance and care 174 Automatic transaxle fluid Follow the scheduled service intervals outlined in the maintenance guide and or service guide. Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and/or dipstick handle and also in the Lubricant specifications section in the Cap[...]

Maintenance and care 175 The transaxle fluid should be in this range if at normal operating temperature 66°C - 77°C (150°F - 170°F). The transaxle fluid should be in this range if at room temperature 10°C - 35°C (50°F - 95°F). If the vehicle has been operated for an extended period at high speeds, in the city during hot weather or pulling a[...]

Maintenance and care 176 Battery Y our vehicle may be equipped with a Motorcraft maintenance-free battery . The Motorcraft maintenance-free battery normally does not require additional water during its life of service. However , for severe service usage or in high temperature climates, refer to the maintenance guide and or service guide for additio[...]

Maintenance and care 177 Battery replacement If your original equipment battery requires replacement while under warranty , it will be replaced with a Motorcraft service battery , identical in design technology . Like the original equipment battery , it should not require water addition during its normal life of service; however , for severe servic[...]

Maintenance and care 178 Batteries normally produce explosive gases which can cause personal injury . Do not allow flames, sparks or lit tobacco to come near the battery . Always cover your face and protect your eyes and also provide ventilation. Applying too much pressure on the ends when lifting a battery could cause acid to spill. Lift the batte[...]

Maintenance and care 179 Relearning the idle function Because your vehicle’ s engine is electronically controlled, some control conditions are maintained by power from the battery . When the battery is disconnected or a new battery is installed, the computer must “relearn” its idle conditions before your vehicle can drive properly . T o begin[...]

Maintenance and care 180 Checking wiper blades Check the wiper blades on your vehicle for roughness by running the tips of your fingers over the edge of the blade. T races of grease, silicone and fuel prevent wiper blades from functioning properly . W e recommend Ford cleaning solutions or equivalent to clean wiper blades. Change the wiper blades o[...]

Maintenance and care 181 2. Remove the plastic caps from the screws on the grille. Remove the screws. 3. Open the hood. Pull off the rubber weatherstrip at the back of the engine compartment. Remove the screws that hold the grille, separate the two halves and remove the grille. 4. The filter is in a housing at the back of the engine compartment, on[...]

Maintenance and care 182 New vehicles are fitted with tires that have their T ire Quality Grade (described below) molded into the tire’ s sidewall. These Tire Quality Grades are determined by standards that the United States Department of T ransportation has set. T ire Quality Grades apply to new pneumatic tires for use on passenger cars. They do[...]

Maintenance and care 183 T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of [...]

Maintenance and care 184 T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to dege[...]

Maintenance and care 185 Checking tire pressure Check the tire pressure periodically after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). Inflate the tires as necessary . T o check the tire pressure, insert the tire pressure gauge into the valve. The cold pressure amount is listed on the Safety Compli[...]

Maintenance and care 186 Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over . Replacing tires Replace tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias- belted, or bias-type tires. Use only the tire si[...]

Maintenance and care 187 Dispose of worn tires in accordance with local environmental regulations. Refer to the Safety Compliance Certification label to determine the specific size tire and wheel Ford Motor Company recommends for use on this vehicle. When purchasing replacement tires for your vehicle, consult your dealer or a qualified service tech[...]

Maintenance and care 188 The tires on your vehicle have all- weather treads to provide traction in rain and snow . However , in some climates, using snow tires and chains may be necessary . Ford offers snow chains as a Ford approved accessory and recommends use of these or their equivalents on approved tires. See your dealer or a qualified service [...]

Maintenance and care 189 Change over from winter to summer tires as soon as road conditions allow , this will reduce fuel consumption and noise in the vehicle’ s interior . • Drive cautiously . If you hear the chains rub or bang against the vehicle, stop and retighten them. If this does not work, remove the chains to prevent vehicle damage. •[...]

Maintenance and care 190 IMPORT ANT FUEL INFORMA TON Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel[...]

Maintenance and care 191 Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Make sure the fuel cap is correctly fitted after fueling. Failure to do so may cause the on board diagnostic system to illu[...]

Maintenance and care 192 Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. The damage may not be covered by your warranty . Y our vehicle was not designed to use fuel containing manganese- based additives such as MMT . Additionally , vehicles certified to California emission s[...]

Maintenance and care 193 Octane recommendations Y our vehicle is designed to use regular gasoline with an (R+M)/2 octane rating of 87. W e do not recommend gasolines labeled as “regular” in high altitude areas that are sold with octane ratings of 86 or even less. Do not be concerned if your vehicle sometimes knocks lightly . However , if it kno[...]

Maintenance and care 194 Fuel filler cap If the “check engine” indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed. T urn off the engine, remove the fuel filler cap and reinstall it being careful to align the cap properly . If you must replace the fuel filler cap, replace it with an autho[...]

Maintenance and care 195 Calculating fuel economy T o accurately calculate your vehicle’ s fuel economy: 1. Fill the tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in litres or gallons). 3. After at least three to five fill- ups, fill the fuel tank and record the current m[...]

Maintenance and care 196 EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use unleade[...]

Maintenance and care 197 W atch for fluid leaks, strange odors, smoke, loss of oil pressure, engine overheating, illumination of the charging system warning light or the check engine warning light. These events could indicate that the emission control system is not working properly . Exhaust leaks may result in entry of harmful and potentially leth[...]

Maintenance and care 198 Do not make any unauthorized changes to your vehicle or engine. By law , vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your veh[...]

Maintenance and care 199 If the vehicle’ s powertrain system or its battery has just been serviced, the OBD-II system is reset to a “not ready for I/M test“ condition. T o ready the OBD-II system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on a[...]

Maintenance and care 200 1 1 2 The bulbs for the low beam, high beam, turn signals and side lamps are housed in the lamp assembly . T o replace a bulb, the complete lamp assembly has to be removed as follows: 1. Switch off the lamps. 2. Open the hood. 3. Remove the lower screw (2) from the headlamp housing. 4. Remove the two upper screws (1) from t[...]

Maintenance and care 201 Reinstalling the headlamp assembly The gasket lining must be seated properly around the lamp assembly when reinstalling. All bulb connectors must be correctly connected. Install in the reverse order . Headlamp – low beam Pull off the connector , release the wire clip and replace the bulb. Pay attention to the tab guides w[...]

Maintenance and care 202 Front turn signal/side lamps Pull the socket out. Pull the bulb out and replace it. Foglamps (if equipped) 1. T urn the bulb counterclockwise and pull it out of the light assembly . 2. Remove the electrical connector . 3. Fit the new bulb in reverse order (do not touch the glass part of the bulb). 31MMCen 4/13/99 2:17 PM Pa[...]

Maintenance and care 203 License plate lamp Unscrew the bulb holder with a screwdriver . Remove the bulb from the clip holder . Replace the new bulb in reverse sequence. Brake/turn signal/tail lamps 1. Disconnect the electrical connector . 2. T urn the socket counterclockwise and pull it out. 3. T urn the bulb counterclockwise and pull it out. 4. T[...]

Maintenance and care 204 High-mounted brake lamp Enter the rear seat compartment. 1. Remove the high mounted stop lamp assembly . 2. Remove the red bulb cover . 3. Remove inoperative stop lamp bulb. T o install, fit the new bulb in reverse sequence. On vehicles equipped with a rear spoiler , the high-mounted brake lamp is included in the spoiler . [...]

Maintenance and care 205 Interior lamps (sunroof equipped vehicles) Open the lamp assembly . The bulbs can be replaced after the contact plate has been hinged back. Interior lamps with reading lamps (if equipped) Remove the clip located on lens to access the center bulb. T o replace the reading lamp bulbs, remove the two retaining screws to access [...]

Maintenance and care 206 Function T rade number 3457 NA 9005 9006 893 1157 1156 Front /turn lamp Headlamp (high) Headlamp (low) Foglamp/License plate lamp Rear tail/turn/brake lamp Backup lamp Bulb specifications 2723 C5W High-mounted brake lamp Interior lamp 211-2 License plate lamp Reading lamp 578 31MMCen 4/13/99 2:18 PM Page 206[...]

Maintenance and care 207 Aiming the headlamps Y our vehicle is equipped with a V ehicle Headlamp Aim Device (VHAD) on each headlamp body . Each headlamp may be properly aimed in the horizontal direction (left/right) and the vertical direction (up/down). A non-zero bubble reading (vertical indicator) does not necessarily indicate out-of-aim headlamp[...]

Maintenance and care 208 Adjusting the horizontal aim 1. Make sure the vehicle is on a level surface . 2.W ith the hood open, locate the horizontal indicator and adjusting screw . Through the viewing hole on the outboard side of the headlamp. 3. T urn the horizontal adjusting screw until the “0” reference mark on the horizontal indicator aligns[...]

Maintenance and care 209 Adjusting the vertical aim The numbers shown on the vial indicate beam direction in degrees up or down. 1. Make sure the vehicle is on level ground. 2. W ith the hood open, locate the bubble level vertical aim indicator , and adjusting screw . It is visible when viewed from the above the rear of the headlamp. 3. T urn the v[...]

Maintenance and care 210 W ashing your vehicle Only use car washing areas that have environmentally friendly drainage systems. VEHICLE CARE W ash your vehicle regularly with cold or lukewarm water . Never use strong detergents or soap. If your vehicle is particularly dirty , use a quality car wash detergent. Always use a clean sponge, washing glove[...]

Maintenance and care 211 W axing your vehicle The best way to determine when the paintwork needs waxing is by noting when water stops beading on the surface. This could be every three or four months depending on operating conditions. Use only carnauba or synthetic- based waxes. Remove any bugs and tar before waxing the vehicle. Use cleaning fluid o[...]

Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, paint repair foil or aerosol spray from the Ford accessories line. Observe the application instructions on the products. Cleaning the wheels W ash the wheels with the same detergent you use to clean the body of your vehicle. Do not use acid-b[...]

Maintenance and care 213 Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup act as insulators and keep the engine warmer than normal. Follow these guidelines to clean your engine: • T ake care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and[...]

Cleaning plastic exterior parts Use a vinyl cleaner for routine cleaning of plastic. Clean with a tar remover if necessary . Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps W ash the exterior lamps with the same detergent you use to wash the exterior of your vehicle. Use glass cleaner or t[...]

Maintenance and care 215 Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner . Remove fresh spots immediately . Follow the directions that come with the cleaner . Cleaning leather seats (if equipped) For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surfac[...]

Maintenance and care 216 Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets and warm water . Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts[...]

Capacities and specifications 217 * Refer to V ehicle Emission Control Information (VECI) decal for spark plug and gap specifications. ** If a spark plug is removed for examination, it must be reinstalled in the same cylinder. If a spark plug needs to be replaced, use only spark plugs with the service part number suffix letter “FE” as shown on [...]

Capacities and specifications 218 Engine oil - with filter - without Manual transaxle 1.9 l (2.0 qts) Automatic transaxle with oil cooler Power steering Cooling system with heating W indshield washer fluid Fuel tank Braking system 4.25 l (4.5 qts) 3.75 l (4.0 qts) 8.5 l (9.0 qts.) 6.6 l (7.0 qts)* 7.1 l (7.5 qts)** Fill to MAX mark Fill to top of r[...]

Capacities and specifications 219 Lubricant Specifications Item Ford part name or equivalent High performance DOT 3 brake fluid, DOT 4 brake fluid or Super DOT 4 Premium engine coolant Motorcraft motor oil 5W -30 super premium MERCON ® power steering fluid Motorcraft MERCON ® A TF* Ultra-clear windshield washer concentrate Ford part number C6AZ-1[...]

Capacities and specifications 220 2.0 litre Engine 2.5 litre Engine 1988 2544 96 (125) 5500 125 (170) 6250 176 (130) 4000 220 (162) 4250 6150 6700 6375 6925 800±50 (880±50) 725±50 (725±50) 1-3-4-2 1-4-2-5-3-6 1.3 Electronically controlled Idle speed (manual transaxle) Engine cm 3 Capacity kW (HP) at rpm Power output Nm (lb-ft) at rpm Max. torqu[...]

Capacities and specifications 221 D A E B C Dimensions mm (inches) 4556 (179.4) 1751 (68.9) 1380 - 1427 (54.3 - 56.2) 2704 (106.5) 1499 - 1518* (59.0 - 59.8) 1483 - 1502* (58.4 - 59.1) A = Maximum length B = Overall width (without mirrors) C = Overall height (curb weight) D = Wheelbase E = T rack Front Rear * Dependent on tyre size 32MCSen 4/13/99 [...]

Capacities and specifications 222 VEHICLE IDENTIFICA TION NUMBER The vehicle identification number (VIN) is attached to a metal tag and is located on the front driver’ s side of the instrument panel. The VIN tag may be seen by looking through the windshield from the outside of the vehicle. 33MMCAen 04/14/1999 9:49 AM Page 222[...]

Customer assistance 223 GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern. Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24-hours, seven days a week • for the Basic warranty period (Canada) or New V ehicle [...]

Customer assistance 224 Ford extended service plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides: • Prot[...]

Customer assistance 225 Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warrant[...]

Customer assistance 226 Please have the following information available when contacting Ford Customer Assistance: • Y our telephone number (home and business) • The name of the dealer and the city where the dealership is located • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehic[...]

Customer assistance 227 • sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle's performance as designed • a request for reimbursement of consequential expenses unless a service or product concern being reviewed • items not covered by the New V ehicle Limited W arranty (inc[...]

Customer assistance 228 T o properly review your case, the Board needs the following information: • legible copies of all documents and maintenance or repair orders relevant to the case • the year , make, model, and V ehicle Identification Number (VIN) listed on your vehicle ownership license • the date of repair(s) and mileage at the time of[...]

Customer assistance 229 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board's decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law . T o re[...]

Customer assistance 230 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen [...]

Customer assistance 231 Ford T riple Clean Ford Ultra-Clear Spray Glass Cleaner * May be sold with the Motorcraft name A wide selection of accessories is available through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are cust[...]

Customer assistance 232 T ravel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adapters Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed [...]

Customer assistance 233 For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GA WR as indicated on the S[...]

Customer assistance 234 ORDERING ADDITIONAL OWNER'S LITERA TURE T o order the publications in this portfolio in the United States: Make checks payable to: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan, 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST ., for credit card holder[...]

Reporting safety defects 235 REPORTING SAFETY DEFECTS (U.S. ONL Y) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to Ford Motor Company . If NHTSA receives similar complaints, it may open an [...]

Index 236 A Page Accessory position on the ignition . . . . . . . . . . . . . . . . . .52 Additives, engine oil . . . . . . . . .165 Air bag supplemental restraint system and child safety seats . . . . . . . .84 description . . . . . . . . . . . . . . . . .83 disposal . . . . . . . . . . . . . . . . . . .88 indicator light . . . . . . . . . . .13, [...]

237 Index C Page Child safety restraints built-in child seat . . . . . . . . . . .93 child safety seats . . . . . . . . . . . .99 children and safety belts . . .89, 91 Child safety seats and air bags . . . . . . . . . . . . . . . .84 attaching with tether straps . .102 automatic locking mode . . . . . .77 Childproof safety locks . . . . . . . .63 C[...]

Index 238 E Page Engine oil changing oil and filter . . . . . . .165 checking and adding . . . . . . . .165 dipstick . . . . . . . . . . . . . . . . . .163 disposal . . . . . . . . . . . . . . . . . .167 engine oil pressure warning light . . . . . . . . . . . . . . .16 filter specifications . . . . . . . . .217 refill capacities . . . . . . . . . .[...]

Index 239 H Page High-mount brakelamp . . . . . . .204 Hood latch location . . . . . . . . . . . . . .162 release lever . . . . . . . . . . . . . .162 Horn . . . . . . . . . . . . . . . . . . . . . . .54 I Identification Number , V ehicle (VIN) . . . . . . . . . . . . . . . . . . . . .222 Idle, relearning . . . . . . . . . . . . .179 Idle, speed . [...]

Index 240 M Page Maintenance (see Servicing) Manual transaxle backing up (reverse) . . . . . . . .125 clutch . . . . . . . . . . . . . . . . . . . .123 fluid, capacity . . . . . . . . . . . . .218 shift speeds . . . . . . . . . . . . . . .124 Mileage, calculating fuel economy . . . . . . . . . . . . . . . . . . .195 Mirrors side view mirrors (power[...]

Index 241 S Page Safety belts (see Safety restraints) Safety chains, when towing a trailer . . . . . . . . . . . . . . . . . . . .134 Safety Compliance Certification Label . . . . . . . . . . . . . . . . . . . . . .132 Safety defects, reporting . . . . . .235 Safety restraints adjusting the safety belts . .77, 79 automatic locking mode (retractors)[...]

Index 242 T Page T ires changing . . . . . . . . . . . . . . . . .146 checking tire pressure . . . . . .185 cleaning . . . . . . . . . . . . . . . . . .212 inspection and maintenance . .185 replacing . . . . . . . . . . . . . . . . .149 rotating . . . . . . . . . . . . . . . . . .185 snow tires and chains . . . . . . .188 spare tire . . . . . . . .[...]

243 4MInden 04/14/1999 9:51 AM Page 243[...]

244 Filling station information UNLEADED FUEL ONL Y Octane 87 58.5 litres (15.4 gallons) Use Motorcraft 5W -30 Formula E Fuel Economy Motor Oil, Ford specification WSS-M2C153-G. Refer to Safety Compliance Certification label on driver’ s door pillar Pull handle under the left side of the instrument panel Right rear of vehicle Fuel Fuel tank capac[...]