Mercury 2000 manuel d'utilisation

Before driving Introduction 2 Instrumentation 6 Controls and features 16 Seating and safety restraints 73 Starting and driving Starting 107 Driving 1 12 Roadside emergencies 129 Servicing Maintenance and care 147 Capacities and specifications 204 Customer assistance 21 1 Reporting safety defects 223 Index 224 All rights reserved. Reproduction by an[...]

The following warning may be required by California law: CALIFORNIA Proposition 65 W arning Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer , or birth defects or other reproductive harm. ICONS Indicates a safety alert. Read the following section on W[...]

W ARNINGS W arnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently . This is necessary to give the mo[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W arning Child Seat T ether Anchorage Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based T raction Control Master Lighting Switch Ha[...]

V ehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System Engine A[...]

A ON OFF + – 0 1 2 20 40 60 80 100 120 20 60 140 180 P R N D 2 1 MPH km/h 000000 000 0 E F C H FUEL DOOR > THEFT LOW COOLANT Parking brake release (pg. 114) Headlamp control (pg. 16) Panel dimmer (pg. 17) Driver air bag (pg. 93) T runk release — sedan only (pg. 56) Rear window wiper and washer — wagon only* (pg. 47) T urn signal and wiper/[...]

VOL PUSH ON AM FM H M EJ TAPE BASS TREB BAL FADE SCAN REW FF R COMP OFF A/C MAX A/C SHUFFLE SIDE 1-2 CD SEEK TUNE DISC 1-6 1 234 56 SET+ RES CST- P ! BRAKE CRUISE RPMx1000 ABS 3 4 5 6 7 Climate control system (pg. 18) Gearshift (pg. 117) Electronic sound system (pg. 28) Auxiliary power point (pg. 28) Speed control (pg. 43) Instrumentation 7[...]

W ARNING LIGHTS AND CHIMES T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter . High beams Illuminates when the high beam headlamps [...]

Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Door ajar Illuminates when the ignition is in the ON or ST ART position and any door is open. Service engine soon Y our vehicle is equipped with a co[...]

3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the[...]

stays on, you should check the coolant level inside the reservoir . For instructions on adding coolant, see Engine coolant in the Maintenance and care chapter . Anti-theft system (if equipped) Refer to Perimeter alarm system (if equipped) and SecuriLock y passive anti-theft system in the Controls and features chapter . Anti-lock brake system (ABS) [...]

Brake system warning Momentarily illuminates when the ignition is turned to the RUN position. Also illuminates if the parking brake is engaged. If the brake warning lamp does not illuminate at these times, or remains on after releasing the parking brake, seek service immediately . One of the following conditions may exist: • low brake fluid level[...]

Safety belt warning chime Sounds to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter . Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter . Key-in-ignition warning ch[...]

T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” [...]

Odometer Registers the total kilometers (miles) of the vehicle. T rip odometer Registers the kilometers (miles) of individual journeys. T o reset, depress the control. Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or[...]

Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the position and the high beams are not turned on. Pull headlamp control towards you to turn foglamps on. The foglamp indicator light will illuminate. P ANEL DIMMER CONTROL Use to adjust the brightness of[...]

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster . The defroster turns off automatically[...]

T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will operate in all modes except(Panel) and (Floor). However , the air conditioning will only function if the outside temperature is about 10?[...]

• (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be [...]

• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If the air conditioner works well in MAX A/C, but not in A/C, this may indicate that the cabin air filter (if equipped) needs to be replaced. • If your vehicle has been parked with the windows closed during hot weather , the air cond[...]

Electronic Automatic T emperature Control (EA TC) system (if equipped) The EA TC system will maintain a selected temperature and automatically control airflow . Y ou can override automatic operation with any of the override controls or the fan speed control. Turning the EA TC on Press AUTO, any of the override controls or the fan speed control. The[...]

Turning the EA TC off Press OFF . The Outside T emperature function will continue to operate until the ignition is turned off. Automatic operation Press AUTO and select the desired temperature. The selected temperature and the word AUTO will appear in the display window . The EA TC system will either heat or cool to achieve the selected temperature[...]

T o control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the temperature control. For continuous maximum cooling, push the temperature control until 16°C (60°F) is shown in the display window . The EA TC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature[...]

The display will show and a bar graph to indicate manual fan operation and relative speed. T o return to automatic fan operation, press AUTO. Manual override controls The override controls are located at the bottom of the EA TC and allow you to determine where airflow is directed. T o return to full automatic control, press AUTO. The air conditioni[...]

• F -Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the outside air temperature is about 10°C (50°F) or higher , the air conditioner will automatically dehumidify the air to reduce fogging. • R (Rear W indow Defroster) — Refer to Rear Window Defroster . • -Distrib[...]

Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again or until any other control is pressed. When the EA TC system is off and OUTSIDE TEMP is pressed, the outside temperature will only be displayed for four seconds. The outside temperature reading is most a[...]

• If the air conditioner works well in MAX A/C but not in normal A/C, this may indicate that the cabin air filter (if equipped) needs to be replaced. • Do not place objects over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield. Also, avoid placing small objects on top of your instrume[...]

V olume/power control Press the control to turn the audio system on or off. T urn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, t[...]

Tune adjust in radio mode • Press the to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press the right side of the control to move to the next frequency up the band (whether or not a listenable station is located there). Hold the cont[...]

3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass/treble adjust • The bass adjust control allows you to increase or decrease the audio system’ s bass output. • The treble adjust control allows you to increase or decrease the audio system’ s treble ou[...]

MACH T Audio System with AM/FM Stereo/Cassette V olume/power control Press the control to turn the audio system on or off. T urn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If y[...]

AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). Press the AM or FM control to enter into radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Pressing the AM or FM controls when the ignition[...]

• Press to select the next disc in the CD changer . Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency[...]

Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) T o stop on a particular selection, press the control again. Radio station memory preset The radio is equipped with six station memory preset controls. Th[...]

• Speaker sound can be adjusted between the front and rear speakers. Inserting a tape Push only slightly when inserting a cassette tape (with the open edge to the right). A cassette deck loading mechanism pulls the tape in the rest of the way . Y ou can switch from CD to tape play by inserting a tape into the cassette deck. T ape/CD select • Pr[...]

• In CD mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. • Y ou can cancel the fast forward mode by pressing T APE, or the FF control. T ape direction select Press SIDE 1–2 to play the alternate side of a tape. Dolby T noise [...]

Setting the clock T o set the hour , press and hold the hour (H) control. When the desired hour appears, release the control. T o set the minute, press and hold the minute (M) control. When the desired minute appears, release the control. Y our vehicle is equipped with a special feature that allows you to access clock mode when the vehicle is not r[...]

3. T urn the magazine (A) over . 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine. If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groo[...]

Ensure that the disc holder is evenly inserted and at the same level as the magazine (A). The unit will not operate if the disc holder is not inserted at the same level (B). Radio power must be turned on to play the CDs in the changer . The magazine may be stored in the glove box when not being used. The CD magazine may be inserted or ejected with [...]

Cleaning compact discs Inspect all discs for contamination before playing. If necessary , clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD changer care • Handle discs by their edges only . Never touch the playing surface. • Do not expose discs to direct sunlight or heat[...]

Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their stre[...]

T RACTION CONTROL Y (IF EQUIPPED) This control can be used to turn the T raction Control y on or off. Refer to the T raction Control y section of the Driving chapter for more information. POSITIONS OF THE IGNITION 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steeri[...]

Do not shift the gearshift lever into N (Neutral) with the speed control on. T o turn speed control off • Press OFF or • T urn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. T o set a speed • Press SET+. For speed control to operate, the speed control must be ON and the vehicl[...]

T o set a higher set speed • Press and hold SET +. Release the control when the desired vehicle speed is reached or • Press and release SET +. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET +. Y ou can accelerate with the [...]

Pressing OFF will erase the previously programmed set speed. T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/ RESUME controls are pressed. It turns off when the speed [...]

Push the control on the end of the stalk to activate washer . Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use. Mist Function T o operate the Mist function of the windshield wipers, push and release the windshield washer control quickly . The wipers will cycle one or two times. Rear w[...]

TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. DOME LAMPS AND MAP LAMPS The front dome lamp is located overhead between the driver and passenger sea[...]

The map lamp controls (if equipped) are located on the dome lamp. Press the controls on either side of each lens on each map lamp to activate the lamps. If equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the controls on either side of each map lamp to activate the lamps. REAR DOME LAMP (IF EQUIPPED) The do[...]

ILLUMINATED VISOR MIRROR (IF EQUIPPED) T o turn on the visor mirror lamps, lift the mirror cover . Adjust the amount of light by sliding the control. MOON ROOF (IF EQUIPPED) T o open, press and hold the rear portion of the control. This will fully open the moon roof. T o close, press and hold the front portion of the control. WIRELESS INTERFACE MOD[...]

Y ou will need a Phone Adapter System (P AS) that is compatible with your cell phone that you install into the center console. This system includes a Phone Adapter Module (P AM) with a W iring Harness and a Hang-Up Cup. For more information, call 1–800–736–9450 to order the Phone Adapter System (P AS) for your specific phone. T o install the [...]

POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down • Press AUTO completely down to the second detent. The driver’ s window will open fully . Depress up to stop window operation. AUTO AUTO AU[...]

Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the left side of the control. Press the right side to restore the window controls. Accessory delay (if equipped) W ith accessory delay , the window switches may be used for up to ten minutes [...]

POWER SIDE VIEW MIRRORS T o adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to disable adjust function. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog wh[...]

CENTER CONSOLE Y our vehicle may be equipped with a variety of console features. These include: • Utility compartment • Bin mat (snap-in) • Cupholders (front and rear) • Coin holder slots • Compact disc changer (if equipped) • T issue holder • Rear A/C vent • Rear ashtray (see your Ford, Lincoln Mercury dealer to obtain rear ashtray[...]

T RUNK REMOTE CONTROL Press the remote trunk release control on the instrument panel to the left of the steering wheel. LIFTGA TE (W AGON ONL Y) Y ou can open and close the liftgate and the liftgate window from outside the vehicle. It cannot be opened from inside the cargo area. • T o open the liftgate window , unlock the liftgate (with the key ,[...]

CARGO AREA FEATURES Storage compartment Y our vehicle comes equipped with a storage compartment in the floor of the cargo area. An additional compartment is in the rear trim panel on the right. Always put the load you are carrying as far forward as possible. Cargo net (if equipped) (W agon) The cargo net secures lightweight objects in the cargo are[...]

T o prevent the possibility of injuries, the fasteners for the cargo area cover must be properly attached to the mounting clips on the rear trim panels. Do not place any objects on the cargo area cover . They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. Rewinding the shade W ith extended use[...]

7. Insert the shade into the side mounting brackets and check to make sure that it operates properly . The cover may cause injury in a sudden stop or accident if it is not securely installed. Cargo utility hooks (Sedan) The utility hooks located in side the trunk can be used to hang small items on. Do not hang more than 12 kg (20 lbs) on the hooks.[...]

Locking the doors/liftgate Press this control to lock all doors and liftgate (wagons). T o confirm all doors are closed and locked, press the control a second time within three seconds. The doors will lock again and the horn will chirp. If any of the doors or liftgate are ajar , the horn will make two quick chirps, reminding you to properly close a[...]

Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s). The system automatically turns off after 25 seconds or when the ignition is turned to the ON [...]

T o program the transmitters yourself: • Insert a key in the ignition and turn from 3 (OFF) to 4 (ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 4 (ON) position. The doors will lock/unlock to confirm that programming mode has been entered. • W ithin 20 seconds, program a remote transmitter by pressing[...]

T o replace the battery: 1. T wist a thin coin between the two halves of the transmitter near the key ring. DO NOT T AKE THE FRONT P ART OF THE TRANSMITTER AP ART . 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together . Replacement of the batter[...]

• Press 7/8 and 9/0 controls on the keyless entry pad at the same time to lock the doors (doors opened or closed). • Open a door and press the power door lock control to lock the doors. There is a 20 second countdown when any of the above actions occur before the vehicle becomes ARMED. Each door/hood or liftgate (wagon) arm individually , and i[...]

Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter . • Unlock the doors by using your keyless entry pad. • Unlock the doors or liftgate with a key . T urn the key full travel (toward the front of the vehicle) to make sure the alarm disarms. • T urn ignit[...]

KEYLESS ENTRY SYSTEM (IF EQUIPPED) W ith the keyless entry keypad, you can: • lock or unlock the vehicle doors and liftgate (wagons) without using the key • open the trunk • arm and disarm the perimeter alarm system (if equipped) See also Remote entry system and Perimeter alarm system in this chapter for more information. Y our vehicle has a [...]

T o exit, press 7/8 and 9/0 simultaneously or allow more than 5 seconds to elapse since a button press occured and the 5 digit keycode will be programed. If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step 1 and release. 3. Press the 1[...]

3. T o unlock the trunk or liftgate (wagon), enter the five-digit factory-set code, then press the 5/6 control within five seconds. Locking the doors and liftgate (wagon), press the 7/8 and 9/0 controls at the same time. This can be done at any time. Autolock Autolock is a feature that will automatically lock all doors when all of the following occ[...]

Deactivating/activating horn chirp There are 2 methods to enable/disable this feature. One through your dealer and the second with a door lock sequence using the following instructions: 1. T urn the ignition key to RUN, then press the door UNLOCK control button 3 times. 2. T urn the ignition key to OFF , then press the door UNLOCK control button 3 [...]

momentary problem if they are too close to the key during engine start. If a problem occurs, turn the ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key . Check to make sure the encoded ignition key is an approved Ford encoded ignition key . Spare SecuriLock y keys can be purchased from your d[...]

2. T urn ignition to OFF and remove the first SecuriLock y key from the ignition. 3. W ithin five seconds of turning the ignition to OFF , insert the second previously programmed SecuriLock y key into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second but no more than five seconds). 4. T urn the ignit[...]

T o open the luggage compartment door (lid) from the inside, pull the illuminated “T” shaped handle and push up on the trunk lid. The material that the handle is made of will glow for hours in the darkness of the luggage compartment following brief exposure to ambient light. The “T” shaped handle will be located either on the luggage compar[...]

SEA TING Adjustable head restraints Y our vehicle’ s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as cl[...]

Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the dr[...]

Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. The control is located on the outboard side of the seat cushion. Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forw[...]

REAR SEATS 2nd seat/Split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additional cargo space. T o lower the seatback(s) from inside the vehicle, pull tab to release seat back and then fold seatback down. When raising the seatback(s), make sure you hear the seat latch into place. 3rd seat (wagon only) The[...]

T o open up the seat: 1. Unlock the floor panel with the key , then use the handle to fold the floor panel toward the front of the car . 2. Remove the cargo cover . The cargo cover must be removed or the seatback will not latch in the upright position. 3. Lift the remote latch release on the left side of the compartment and fold the remaining floor[...]

SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of air bag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safet[...]

common, moderate-severity impacts. A higher energy level is provided for the most severe impacts. Whether or not the air bag deploys at all can also be different for the driver versus the passenger based upon driver’ s seat position and safety belt usage allowing further tailoring of the system. Determining if the personal safety system is operat[...]

When are the front air bags and pretensioners deployed? Front air bags and pretensioners are designed to activate in frontal and near -frontal collisions, not rollover , side-impacts, or rear -impacts unless the collision causes sufficient longitudinal deceleration. The fact that the pretensioners or air bags did not activate in a collision does no[...]

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . Never wear the shoulde[...]

Energy management retractors Y our vehicle has a seat belt system equipped with energy management retractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in a controlled manner . This feature is designed to help further reduce the risk of force-related injuries to th[...]

Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • Anytime a child safety seat is installed in the vehicle. Children 12 years old and[...]

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensiti[...]

Safety belt usage sensors The driver and front outboard passenger safety belt buckles are equipped with sensors that detect if the safety belts are fastened. The sensors provide information to the Personal Safety System which can then adapt the air bag deployment or safety belt pretensioner activation based upon safety belt usage. The Personal Safe[...]

Lap belts Adjusting the lap belt The lap belt does not adjust automatically . The lap belts should fit snugly and as low as possible around the hips, not around the waist. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and[...]

When the adjust tongue of the lap/shoulder combination seat belt is latched into the buckle, the tongue will allow the lap portion to become shorter , but locks the webbing in place to restrict it from becoming longer . Before you reach and latch a combination lap and shoulder belt having an adjust tongue into the buckle, you may have to lengthen t[...]

T o unfasten the belt, push the red release button on the end of the buckle. This allows the tongue to unlatch from the buckle. While the belt retracts, guide the tongue to its original position to prevent it from striking you or the vehicle. Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8[...]

Belt minder (if equipped) The Belt Minder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’ s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster . If... Then... The driver?[...]

The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... 9 Crashes are rare events 9 36 700 crashes occur every day . The more we drive, the more we are exposed to 9 rare 9 events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lif[...]

One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only . The safety belt needs to be latched for a minimum of 3 seconds before belt minder is disabled. Deactivating/activating the belt minder feature Read step s1-9 thoroughly before proceeding wit[...]

• After step 5 the safety belt warning light will be turned on for three seconds. 6. W ithin seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7. Confirmation of disabling Belt Minder is [...]

AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM Y our vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity . This information will a[...]

The air bag supplemental restraints are an intergral part of the Personal Safety System. They are designed to be deployed in cases where the Personal Safety System has determined the occupant conditions and crash severity are appropriate to activate these devices. Refer to the Personal Safety System section in this chapter . Important supplemental [...]

• Recline the seat slightly (one or two degrees) from the upright position. Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury . Do not attempt to service, repair , or modify the Air Bag Supp[...]

Determining if the system is operational The supplemental restraint system uses a warning indicator in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Restraints W arning Indicator section in the Instrumentation chapter . Routine maintenance of the air bag is not required. A difficulty with the system [...]

facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control. Several air bag system co[...]

How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagn[...]

Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the [...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. When possible, always place children under age 12 in the rear seat of your vehicle. Accident stat[...]

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or co[...]

of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps. Carefully follow all of the manufacturer’ s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or collis[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. T o lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child sea[...]

1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback. 3. Locate the corre[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use [...]

2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. T urn the key to 4 (ON) without turning the key to 5 (ST ART). If there is difficulty in turning the key , firmly rotate the steering wheel left and right until the key turns freely . This condition may oc[...]

Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 [...]

Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below . For best resul[...]

Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.[...]

BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the b[...]

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. W ith the ABS light on, the anti-lock brake system is disabled and normal braking is sti[...]

Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and m[...]

Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . T RACTION CONTROL Y (IF EQUIPPED) Y our vehicle may be equipped with the optional T raction Control y system. This system helps you maintain the stability and steerability of your vehicle. It is especial[...]

During T raction Control y operation, the traction control active light will illuminate, you may hear an electric motor type of sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator . This is normal system behavior . The T raction Control y on/off switch, located on the right side of [...]

AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the br[...]

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your dealer or a qualified service technician. Driving with an automatic overdrive transaxle Y our automatic transaxle electronically controls the shift feel by using an adaptive learning strategy . This feature is de[...]

Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This locks the transaxle and prevent the front wheels from rotating. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whe[...]

N (Neutral) W ith the gearshift lever in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. (Overdrive) The (Overdrive) position is the normal driving position for an automatic overdrive transaxle. When in the (Overdrive) position, the transaxle works the same way as when in D[...]

When to use D (Drive) The D (Drive) position eliminates the needless shifting back and forth between third and fourth gears that your vehicle may do when driving on hilly terrain. It also gives more engine braking than overdrive to slow your vehicle on downgrades. 1 (First) Use 1 (First) for when added engine braking is desired when descending stee[...]

When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). T urn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running. If you do not take these precautions, your vehicle may move unexpe[...]

• Maximum T railer W eight: Maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow . It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. • T railer W eight Range: Specified weight range that the trailer must fall within that ranges fro[...]

If driving through deep or standing water is unavoidable, proceed very slowly . Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars). Once through the water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by movi[...]

The amount of weight that you can tow depends on the type of engine in your vehicle. See the following charts: 3.0L 2-V alve V ulcan Engine Model Passenger Load - #/kg (lbs.) Luggage Load - kg (lbs.) Max T railer Wt.- kg (lbs.) Sedan 5/340 (750) 0 365 (800) 4/270 (600) 70 (150) 365 (800) 2/135 (300) 70 (150) 500 (1 100) 2/135 (300) 0 565 (1 250) W [...]

Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper . Use a load carrying hitch. Y ou must distribute the load in your trailer so that 10% of the to[...]

Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer . • Use D (Drive) or a lower gear when towing up or down steep hills. This will eliminate [...]

All Front Wheel Drive (FWD) vehicles An example of recreational towing is towing your vehicle behind a Motorhome. The following recreational towing guidelines are designed to ensure that your transmission is not damaged. It is not recommended to tow front wheel drive vehicles with the front drive wheels on the ground. It is recommended to tow your [...]

GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New V ehicle Limited W arranty peri[...]

Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer . Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance[...]

If your vehicle is a sedan, the fuel pump shut-off switch is located on the right side of the trunk behind the trunk liner . If your vehicle is a wagon, the fuel pump shut-off switch is located behind the service panel on the right side of the cargo area. Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to t[...]

FUSES AND RELA YS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating[...]

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. T o remove a fuse use the fuse puller tool provided on the fuse panel cover . The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Desc[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 13 20A Cigar Lighter , Auxiliary Power Point 14 — Not Used 15 30A Front Wiper Motor 16 15A Flasher and GEM Power , Integrated Control Panel (ICP) Power , RCC Memory , Cluster 17 15A Stop Lamp, Speed Control Deactivating Switch 18 — Not Used 19 — Not Used 20 — N[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 37 15A T ransmission Position Switch 38 5A GEM Park Neutral Switch 39 — Not Used 40 — Not Used 41 — Not Used 42 — Not Used Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current f[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 60A** Fuse Junction Panel 2 30A** PCM Relay 3 60A** Fuse Junction Panel 4 — Not Used 5 — Not Used 6 — Not Used 7 40A** Starter Relay , Ignition Switch 8 20A** T ransit Relay (Export only) 9 40A** Cooling Fan Relays 10 — Not [...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 21 15A* Left Headlamp 22 10A* A/C Clutch Relay , PCM Keep Alive Power 23 — Starter Motor Relay 24 — Low Speed Fan Relay 25 — W iper Speed Relay 26 30A* Generator 27 5A* Rear Control Unit, Antenna 28 15A* HEGO Sensor T ransmission Shift Solenoid, Canister V ent, A/C Clutch [...]

When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle’ s reduced ground clearance • try to repair the[...]

• In the sedan, these are located in the trunk cargo area storage compartment. • In the wagon, they are stored in the left side rear trim panel for the temporary spare and in the floor cargo area storage compartment for the full size spare. 3. If equipped with a wheel cover that’ s bolted on, loosen the five plastic nuts with the lug nut wren[...]

5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. Put the jack in the jack notch next to the door of the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. 7. Remove the lug nuts with the lug nut wrench. 8. Replace the fla[...]

11. Return the flat tire, jack and lug wrench to their proper storage locations. Make sure the jack is fastened so it does not rattle when you drive. 12. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do n[...]

4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. T urn the heater fan on in both vehicles to protect any electrical surges. T urn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) t[...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable. Make the connection to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake m[...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If your vehicle [...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your ?[...]

Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch located in the center between the hood and the grille. 3. Lif[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.0L V6 V ulcan engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Engine oil filler cap 6. Engine oil dipstick 7. Power steering fluid reservoir 8. Engine coolant reservoir 9. W indshield washer fluid reservoir 7 8 6 5 4 3 9 1 2 Maintenance [...]

3.0L DOHC V6 Duratec engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Engine oil filler cap 6. Engine oil dipstick 7. Engine coolant reservoir 8. W indshield washer fluid reservoir 9. Power steering fluid reservoir 7 6 5 4 8 9 1 2 3 Maintenance and care 150[...]

ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P . 4. Open[...]

• If the oil level is below the add 1QT or MIN mark, add enough oil to raise the level within the 1QT -FULL or the MIN-MAX range (depending on application). • Oil levels above the F in FULL or above the MAX mark, may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it[...]

Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -30 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API certification trademark will meet all requirements for your vehicle’ s engine. Ford oil specification is WSS-M2C153-G. Do not use supplemental [...]

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir . 2. Visually inspect the fluid level. 3. If necessary , add brake fluid from a [...]

WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way . Only use a washer fluid that meets Ford specifications. Refer to Lubrica[...]

Checking and adding washer fluid for the liftgate (if equipped) The opening for the reservoir is located on the passenger side under the tail lamp. Refill this reservoir with the same fluid you use for your windshield. ENGINE COOLANT Checking engine coolant Y our engine’ s cooling system has been factory-filled with a 50/50 mixture of distilled w[...]

The engine coolant must be maintained at the correct fluid level and concentration to work properly . If the engine coolant fluid level and concentration is not maintained correctly , damage to the engine and cooling system may result. When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be[...]

Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or a premium engine coolant that meets Ford specification ESE-M97B44-A. • DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color). • DO NOT USE a DEX-COOL t engine coolant or an equivalent engine coolant that meets Ford [...]

• Engine coolant concentrations above 60% or below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. Plain water may be added in an emergency , but you must replace it with a 50/50 mixture of engine coolant and distilled water as soon as possible. Check the coolant level in the reservoir be[...]

Always dispose of used automotive fluids in a responsible manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter . Fill your e[...]

V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the Scheduled Maintenance Guide for the service interval schedules. If adding fluid is necessary , u[...]

3.0L V6 V ulcan engine 4. Check the fluid level on the dipstick. It should be between the arrows in the FULL HOT range. Do not add fluid if the level is within this range. 5. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the FULL HOT range. Be sure to put the dipstick back in the reservoir . 3.0L[...]

Automatic transmission fluid expands when warmed. T o obtain an accurate fluid check, drive the vehicle until it is warmed up (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer , the vehicle should be turned off for about 30 minutes to al[...]

High fluid level Fluid levels above the safe range may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct t[...]

CABIN AIR FIL TER (IF EQUIPPED) The particulate air filtration system is designed to reduce the concentration of airborne particles such as dust, spores and pollen in the air being supplied to the interior of the vehicle. The particulate filtration system gives the following benefits to customers: • Improves the customer’ s driving comfort by r[...]

1. Release and open the hood. 2. Remove the four clips located on the cowl vent screen. Maintenance and care 166[...]

3. Remove the cowl vent screen. 4. Remove the two screws retaining the cowl top inner panel shield. 5. Remove the inner panel shield. Maintenance and care 167[...]

6. Remove the filter from the cabin air filter housing. 7. Install the new cabin air filter into the cabin air filter housing. Maintenance and care 168[...]

8. Replace the inner panel shield. 9. Replace the two screws retaining the cowl top inner panel shield. 10. Replace the cowl vent screen. Maintenance and care 169[...]

11. Replace the four clips located on the cowl vent screen. BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guid[...]

If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the [...]

2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. T urn the A/C on and allow the engine to idle for at least one minute. 6. W ith your foot on the brake pedal and with the A/C on, put the vehicle in[...]

Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wi[...]

U.S. Department of T ransportation-T ire quality grades: The U.S. Department of T ransportation requires Ford to give you the following information about tire grades exactly as the government has written it. T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specifi[...]

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check t[...]

Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity . Use only the tire co[...]

recommended that steel wheels are used of the same size and specifications as those originally installed. Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory or equivalent. SAE class “S” or other conventional link type chains may cause damage to the vehicle’ s wheel house an[...]

Automotive fuels can cause serious injury or death if misused or mishandled. Gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automot[...]

splashed on the skin, promptly wash skin thoroughly with soap and water . Consult a physician immediately if you experience an adverse reaction. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be[...]

reinstall it securely . The indicator should turn off after three driving cycles with the fuel filler cap properly installed. A driving cycle consists of a cold engine start-up followed by mixed city/highway driving. If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty m[...]

with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particula[...]

Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter . Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft [...]

• Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time. Y our results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the [...]

• Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy . • Slow down gradually . • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy . •[...]

• Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • T ransmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Close windo[...]

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power , could indicate t[...]

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. BULBS Replacing exterior bulbs Check the operation of the followi[...]

Replacing headlamp bulbs T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Remove the bolt from the headlamp housing. 3. At the back of the headlamp, pry up and remove the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward. 4. Remove the protective dust shield from the housi[...]

5. Disconnect the electrical connector from the bulb by pulling rearward. 6. Remove the bulb retaining ring by rotating it counterclockwise. 7. Remove the old bulb from the lamp assembly by pulling it straight out of the lamp assembly . T o install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the[...]

2. Install the bulb retaining ring over the plastic base and lock the ring by rotating clockwise until it snaps into place. 3. Connect the electrical connector to the bulb. 4. Install the protective dust shield and lock the shield by rotating it clockwise until it locks into position. 5. Carefully position the headlamp assembly onto the vehicle. 6.[...]

5. Carefully pull bulb straight out of the socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly by rotating it clockwise. 7. Carefully position the headlamp assembly onto the vehicle. 8. Hold the headlamp assembly snugly against the vehicle and install the retainer pins straight down to lock the lamp into place. 9. Bef[...]

Replacing license plate lamp bulbs The following procedure is for wagons only . For sedans, refer to a qualified technician. 1. Remove screw and the license plate lamp assembly from liftgate. 2. Remove bulb socket by turning counterclockwise. 3. Carefully pull the bulb out from the socket and push in the new bulb. 4. Install the lamp assembly on li[...]

4. Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly . 5. Pull the bulb from the socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly by rotating it clockwise. 7. Install the lamp assembly on the vehicle with four nut and washer assemblies ensuring the washers on the nuts [...]

Replacing the interior bulbs Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp For bulb replacement, see a dealer or qualified technician. Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America a[...]

Function Number of bulbs T rade Number Front park/turn lamp 2 3457 NAK (amber) Headlamp 2 9007 QL (9007 LL optional) T ail lamp/brake/turn lamp 2 3157 T ail lamp/brake lamp (wagon) 2 3157 Rear turn lamp (wagon) 2 3156K Backup lamp 2 921 Backup lamp (wagon) 2 3156K License plate lamp 2 168 High-mount brake lamp 3 912 Rear side marker lamp (wagon) 2 [...]

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. V ertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen di[...]

3. On the wall or screen you will observe an area of high intensity light. The top of the high intensity area should touch the horizontal reference line, if not, the beam will need to be adjusted. T o see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other . 4. Locate the vertical adjus[...]

W ashing your vehicle W ash your vehicle regularly with cold or lukewarm water . Never use strong detergents or soap. If your vehicle is particularly dirty , use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. T o avoid spots, avoid washing when the hood is still warm, i[...]

Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra T ouch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer T ouch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above)[...]

Cleaning the exterior lamps W ash with the same detergent as the exterior of your vehicle. If necessary , use a tar remover such as Ford Extra Strength T ar and Road Oil Remover (B7A-19520–AA). T o avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades, windshield and rear windo[...]

• 3.0L V ulcan engine • 3.0L Duratec engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Maintenance and care 201[...]

Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. A void cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection. Do not use chemical solvents or strong detergents when cleaning the steering w[...]

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been involved in an[...]

MOTORCRAFT PART NUMBERS Component 3.0L V6 V ulcan engine 3.0L DOHC V6 Duratec engine Air filter element 1 F A-1683 F A-1683 Fuel filter FG-1006 FG-81006 Battery (standard) BXT -58R BXT -36R Battery (optional) BXT -36R N/A Oil filter FL-400-S FL-820-S PCV valve EV -228 EV -243 Spark plugs 2 A WSF-32PP 3 AGSF-32W 1 Do not use oil-impregnated air filt[...]

REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid All Fill to line on reservoir Engine coolant 1 Premium Engine Coolant 3.0L V6 V ulcan engine 11.0L (11.6 quarts) 3.0L DOHC V6 Duratec engine 10.0L (10.6 quarts) Engine oil (includes filter change) Motorcraft SAE 5W -30 Super Pre[...]

LUBRICANT SPECIFICATIONS Items Ford Part Name or equivalent Ford Part Number Ford Specification Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid C6AZ-19542-AB ESA-M6C25-A and DOT 3 Door latch, hood latch, auxiliary hood latch, seat tracks, trunk and liftgate latches Multi-Purpose Grease DOAZ-19584-AA or F5AZ-19G209-AA ESA-M1C93-B or ES[...]

ENGINE DATA Engine 3.0L V6 V ulcan engine 3.0L DOHC V6 Duratec engine Cubic inches 182 183 Required fuel 87 octane 87 octane Firing order 1-4-2-5-3-6 1-4-2-5-3-6 Spark plug gap 1.07-1.17 mm (0.042-0.046 inch) 1.3-1.4 mm (0.052-00.056 inch) Ignition system EDIS Coil on plug Compression ratio 9.3:1 10.0:1 VEHICLE DIMENSIONS V ehicle dimensions Sedan [...]

5 2 3 4 1 Capacities and specifications 208[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side. 1 4 MFD. BY FORD MOTOR CO. IN U[...]

V ehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number .) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on t[...]

Ford Extended Service Plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides the following: • benefits durin[...]

If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern can[...]

If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center 1680[...]

replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss W arranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an [...]

Concerns are ineligible for review if the New V ehicle Limited W arranty has expired at receipt of your application and, in certain states eligibility is dependent upon the customer’ s possession of the vehicle. Eligibility may differ according to state law . For example, see the unique brochures for California, W est Virginia, Georgia and W isco[...]

• a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve your concern Y ou will receive a letter of explanation if your application does not qualify for Board review . Oral presentations If you w[...]

Y ou may also contact the North American Customer Assistance Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P .O. Box 6248 Dearborn, Michigan 48121 UTILIZING THE MEDIATION/ARBITRATION PROGRAM[...]

The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. In the United States, using leaded fuel may also result in difficult[...]

Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength T ar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (Canada only) Ford Extra Strength Upholstery Cleaner (not available in Canada) Ford Metal Surface Cleaner Ford Multi-Purpose Cleaner* M[...]

Comfort and convenience Cabin air filter Cargo nets Cargo organizers Cargo shades Engine block heaters T ravel equipment Auto headlamps with DRL Daytime running lights (DRL) Electrochromic inside mirror with compass Electrochromic inside mirror with compass and temperature Factory luggage rack adaptors Framed luggage covers Heavy-duty battery Remov[...]

Rear decklid spoilers T ouch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle ([...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio: Make checks payable to: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST , for credit card holders only Obtaining a French owner ’ s guide French[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

Accessory delay ..........................53 Air bag supplemental restraint system ................93,94,97 and child safety seats .............. 95 description ...........................94,97 disposal ...................................... 99 driver air bag ..................93,96,98 indicator light ......................12,96 operation .........[...]

windows .................................. 202 wiper blades ............................ 200 woodtone trim ........................ 202 Climate control (see Air conditioning or Heating) ............ 18 Clock .......................................31,38 Console ........................................ 55 Controls power seat .........................[...]

improving fuel economy ........ 182 low fuel warning light .............. 10 octane rating .................... 180,207 quality ...................................... 181 running out of fuel ................. 181 safety information relating to automotive fuels ..................... 177 Fuses ...................................132,133 Gas cap (see F[...]

anti-lock brakes (ABS) ..... 11,113 anti-theft ................................... 11 brake .......................................... 12 charging system ........................ 12 check coolant ............................ 11 cruise indicator ......................... 11 door ajar ...................................... 9 high beam ...............[...]

Specification chart, lubricants ............................206,207 Speed control .............................. 43 Speedometer ............................... 13 Starting your vehicle ......... 107,109 jump starting .......................... 141 Steering wheel tilting ......................................... 48 T achometer ......................[...]

229[...]

230[...]

Item Information Required fuel Refer to 9 Octane recommendations 9 in the Maintenance and care chapter . Fuel tank capacity 68.1L (18 gallons) Engine oil capacity (including filter change)-3.0L V6 V ulcan engine 4.25L (4.5 quarts) Use Motorcraft SAE 5W -30 Super Premium Motor Oil, Ford specification WSS-M2C153-H. Engine oil capacity (including filt[...]

1 Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter . 2 Ensure the correct automatic transmission fluid is used. T ransmission fluid requirements are indicated on the dipstick or on the dipstick handle. MERCON t and ME[...]