Mitsubishi Electronics -NZ2GF2B-60DA4 manuel d'utilisation

CC-Link IE Field Network Digit al-Analog Converter Module User's Manual -NZ2GF2B-60DA4[...]

[...]

1 SAFETY PRECAUTIONS (Read these pre cautions before using this pr oduct.) Before using this product, p lease read this manual and the relevant manuals carefu lly and pay full attention to safety to handle the product correctly . The precautions given in this manual are concern ed with this product o nly . For the safety precautions of the programm[...]

2 [Design Precautions] [Inst allation Precautions] [Inst allation Precautions] [Wiring Precautions] [Wiring Precautions] CAUTION ● Do not install the control lines or communication c ables together with the main circuit lines or power cables. Keep a distance of 100mm or more between them. Failure to do so may result in malfunction due to noise. ?[...]

3 [Wiring Precautions] [S t artup and Maintenance Precautions] CAUTION ● Use applicable solderless terminals and tigh ten them within the specifie d torque range. If any spade solderless terminal is used, it may be disconnec ted when a terminal block screw comes loose , resulting in failure. ● Check the rated voltage and terminal layout bef ore[...]

4 [S t artup and Maintenance Precautions] [S t artup and Maintenance Precautions] [Disposal Precautions] CAUTION ● Do not disassemble or modify the mo dule. Doing so may cause failure, malfunction, injury , or a fire. ● Do not drop or apply strong shock to the module. Doing so may damage the module. ● Shut off the external power supply (all p[...]

5 CONDITIONS OF USE FOR THE PRODUCT (1) Mitsubishi programmable con troller ("the PRODUCT") shall be used in conditions; i) where any problem, fault or failure occurring in the PRODUCT , if any , shall not lead to any major or serious accident; and ii) where the backup and fail-safe function are syst ematically or automatical ly provided [...]

6 INTRODUCTION Thank you for purchasing the CC-Lin k IE Field Network digital-analog converter module (h ereafter a bbreviated as D/A converter module). This manual describes the operatin g procedure, system configuration, parameter settings, functions, and troubleshooting of the D/A converter modu le. Before using this product, plea se read this m[...]

7 RELEV ANT MANUALS (1) CC-Link IE Field Ne twork (relevant) manuals When using the CC-Link IE Field Network for the first ti me, refer to CC-Link IE Field Ne twork Master/Local Module User's Manual or Simple Moti on Module User's M anual first. The following s hows the structu re of the CC- Link IE Field Network manuals. (2) Operating ma[...]

CONTENTS 8 CONTENTS SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CONDITIONS OF USE FOR THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . [...]

9 CHAPTER 7 V ARIOUS SETTINGS 63 7.1 Parameter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 7.2 Changing t he Pa rameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 7.2.1 Changing the network configu[...]

10 APPENDICES 151 Appendix 1 Details of Remot e I/O Sign als . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Appendix 1.1 Remote input signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Appendix 1.2 Re mote output signals . . . . . . . . . . . . . . . . . . . . . .[...]

11 MANUAL P AGE ORGANIZA TION In this manual, pages are organized and the symbols are used as shown below . The following illustration is for explanation purpo se only , a nd should not be referred to as an actual documentation. *1 The mouse operation exam ple is provided below . The section of the current page is shown. The chapter of the current [...]

12 TERM Unless otherwise specified , this manual uses the following terms. Te r m Description CC-Link IE Field Network A high-speed and large-cap acity open field network that is based on Et hernet (1000BASE-T) D/A converter module The abbreviation for the CC-Link IE Fiel d Network digital-analo g converter module GX Works2 The product name of the [...]

13 Main module A module with the CC-Link IE Field Network communi cat ion function, which can be used as a single remote module. Dedicated instruction An instruction that simplifi es progr amming for using functions of intelligent function modules Extension module A remote module that does not suppo rt the CC-Link IE Field Network communi cation fu[...]

14 P ACKING LIST The following items are included in th e package of this pr oduct. Before use, check that all the items are included. D/A converter module Module Before Using the Product[...]

15 CHAPTER 1 D/A CONVERTER MODULE 1 1.1 Application CHAPTER 1 D/A CONVERTER MODULE This chapter describes the ap plications and features of the D/A converter module. 1.1 Application This module converts the digital data to the analog signal and outputs it to the external devices. The digital data is set from the master station. The D/A converter mo[...]

16 1.2 Features (1) A vailable flexible system configuration Adopting the connection block typ e enables the comb ination of the main module and extension module. Because various extension mo dules can be co nnect ed, a flexib le configuration can be achieved . In addition a poor contact of the extension module can be found promptly because the mai[...]

17 CHAPTER 1 D/A CONVERTER MODULE 1 1.2 Features (7) Error detection a nd monitoring available When a digital value excee ds the range set in advance, an alert is d etected. Thus, an error of dig ital value can be monitored and outp uts of a digital value can be limited. (8) Output available without influence from the sequence scan or link scan An [...]

18 (10)V arious inst allation methods The module can be installed in six directions using a DIN rail. (1 1) Easy module replacement Because the 2-piece structure is adopted for the termi nal block for module power supply and FG and termina l block for analog output signals, the module can be repl aced with the wire connected. In addition, because t[...]

19 CHAPTER 2 P ART NAMES 2 CHAPTER 2 P ART NAMES The section describes part names of the D/A converter module. No. Name Application 1) S tation number setting switch A rotary switch for the following setting and test. • S tation Number Setting ( Page 45, Section 6.1) • Offset/Gain Setting ( Page 69, Section 7.2) • Unit T est ( Page 148, Secti[...]

20 2) PW LED (green) Indicates the operating status of the D/A converter module. ON Power supply ON OFF Power supply OFF RUN LED (green) Indicates the operating status of the D/A converter module. ON Operating normally . Writing dat a to the nonvolatile memory in the offset/gain setting mode. OFF A major error has occurred or in the offset/gain set[...]

21 CHAPTER 2 P ART NAMES 2 3) P1 PORT1 connector for CC-Link IE Field Network (RJ45 connector) Connect an Ethernet cable. ( Page 54, Section 6.5) There are no restrictions on the connection or der of the cables for the "P1" connector and "P2" conn ector . L ER LED (red) ON • The module has received abnormal data. • The modul[...]

22 (1) Module st atus and LED st atus The following table lists the correspondence be tw een the module status and the LED status. *1 Either of ON, Flashing, or OFF . *2 Either of ON or OFF . *3 When the module is failed, the LED may not turn on. Module status Data link status LED status PW LED RUN LED MODE LED D LINK LED ERR. LED ALM LED O/G LED N[...]

23 CHAPTER 3 SPECIFICA TIONS 3 3.1 General Specifications CHAPTER 3 SPECIFICA TIONS This chapter de scribes the specifi c ations of the D/A co nverter module. 3.1 General S pecifications *1 Do not use or store the D/A converter module under pressu re higher than the atmospheric pr essure of altitude 0m. Doing so may cause malfunction. When using th[...]

24 T o use the D/A converter module complyin g with the EMC Directive, refer t o "EMC and Low V oltage Directives" in this manual. ( Page 180, Appendix 7)[...]

25 CHAPTER 3 SPECIFICA TIONS 3 3.2 Performance Specifications 3.2 Performance S pecifications Item Description S tation type Remote device station Number of analog output points 4 points (4 channels)/module Digital input 16-bit signed binary (-16384 to 16383, -288 to 12287, -12288 to 12287) Analog output Volt age -10 to 10VDC (external load resista[...]

26 *1 For details on the I/O conversion char acteristics, refer to the following. • I/O Conversion Characteristic of D/A Conversion ( Page 176, Appendix 4) *2 Except when receiving noise influence. *3 Do not connect two or more wires to the terminal. Applica ble solderless terminal T erminal block for module power supply and FG *3 TE 0.5-10 (Nich[...]

27 CHAPTER 3 SPECIFICA TIONS 3 3.3 Calculating Current Consumption 3.3 Calculating Current Consumption The total current consumption of the modules is calculated by summing th e module power supply curre nt in the main module and extension module. The power supply current in the extension module shou ld be within 30mA. For the value of the module p[...]

28 3.4 Function List Item Description Refe rence D/A conversion enable/disable function Whether to enable or disable D/A conv ersion can be set for ea ch channel. Disabling the D/A conversion for unused channels reduces the conversion cycles. Page 80, Section 8.3 D/A output enable/disable function Whether to output th e D/A conversion va lue or the[...]

29 CHAPTER 3 SPECIFICA TIONS 3 3.5 List of Remote I/O Signals 3.5 List of Remote I/O Signals This section lists I/O signals for a master/local mo dule. The device numbers shown are the example with the remote I/O signals of the main module assigned to th e I/O numbers of RX0 to RX1F and RY0 to R Y1F . Remote input (RX) indicates the input signal fr[...]

30 Do not use any "Use prohib ited" remote I/O signals. If any of the signals are used, correct opera tion of the module cannot be guaranteed. (1) Remote I/O signal of the extension module The remote I/O signal differs depending on the model of the extension mo dule. • Extension I/O module Refer to the followin g. CC-Link IE Field Netwo[...]

31 CHAPTER 3 SPECIFICA TIONS 3 3.6 List of Remote Register 3.6 List of Remote Register This section lists remote registers for a master/local module. The remote registers shown are th e example with the remote registers of the main modul e assigned to the remote registers of RW r0 to RWrF and RWw0 to R WwF . Remote register (RW r) is the informatio[...]

32 3.7 List of Remote Buffer Memory This section lists the r emote buffer me mory areas of the D/A converter module. The remote buffer memory areas of the main module and extension module a re assigned as sh own below . Ex. Example of the remote buffer memory in the manual For details on the remote buffer memory for the D/A converter module, refer [...]

33 CHAPTER 3 SPECIFICA TIONS 3 3.7 List of Remote Buffer Memory *1 For the REMFR and REMTO instructions, refer to the following. User's manual for the ma ster/local module used *2 For the access method, refer to the following. • Parameter area ( Page 63, Section 7.1) • Error history area ( Page 135, Section 1 1.1 ) Do not access the system[...]

34 *1 This is the value at default or initialization by Parameter area initialization command (address: 1002 H ). *2 This shows whether read or write from pr ograms is possible. R: Readable W: Writable Module-based parameter data (main module) 256, 257 0100 H, 0101 H System area - - 258 0102 H D/A conversion enable/disable setting 000F H R/W 259 01[...]

35 CHAPTER 3 SPECIFICA TIONS 3 3.7 List of Remote Buffer Memory (a) Parameter area of the extension module The remote b uffer memory differs dependi ng on the model of t he extension mo dule. • Extension input module (NZ2EX2B1 -16D) *1 This is the value at default or initialization by Parameter area initialization command (address: 1002 H ). *2 T[...]

36 (2) Monitoring area (address: 0500 H to 09FF H ) *1 This is the value for when the module power supply is tur ned off and on or at the remote reset. *2 This shows whether read or write from pr ograms is possible. R: Readable W: Writable (a) M onitoring area of the extension module The remote buffer memory differs depending on th e model of the e[...]

37 CHAPTER 3 SPECIFICA TIONS 3 3.7 List of Remote Buffer Memory *1 This is the value for when the module power supply is tur ned off and on or at the remote reset. *2 This shows whether read or write from programs is p ossible. R: Readable W: Wr it ab le 1812 to 1813 0714 H to 0715 H Number of ON times integration value Y2 0 R 1814 to 1815 0716 H t[...]

38 (3) Error history area (address: 0A00 H to 0FFF H ) Ty p e Address Descrip tion Default *1 Read/Write *2 Decimal Hexadec imal S tation-based error history da ta 2560 0A00 H Error history 1 Error code 0000 H R 2561 0A01 H Order of generation 0000 H R 2562 0A02 H [Error time] First two digits of the year/Last two digits of the year 0000 H R 2563 0[...]

39 CHAPTER 3 SPECIFICA TIONS 3 3.7 List of Remote Buffer Memory *1 This is the value at default or initializa tion by Error history clear command (address: 1000 H ). *2 This shows whether read or write from programs is p ossible. R: Readable W: Wr it ab le (4) Module control dat a area (address: 1000 H to 14FF H ) *1 This is the value for when the [...]

40 (a) M odule control dat a area of the extension module The remote buffer memory differs depending on th e model of the extension module. • Extension input module (NZ2EX2B1-16D) *1 This is the value for when the module power supply is tur ned off and on or at the remote reset. *2 This shows whether read or write from pr ograms is possible. R: R[...]

41 CHAPTER 4 THE PROCEDURE BEFORE OPERA TION 4 CHAPTER 4 THE PROCEDURE BEFORE OPERA TION This section describes the procedure before operation . *1 T o r eplace the module, refer to this section. T o replace the module, follow the procedure described below. • Power off the module and remove the D/A conver ter module. • Prepare a new D/A convert[...]

42 Memo[...]

43 CHAPTER 5 SYSTEM CONFIGURA TION 5 5.1 D/A Converter Module System Configuration CHAPTER 5 SYSTEM CONFIGURA TION This chapter describes syst em configuration using a D/A converter module. For CC-Link IE Field Network configuration, refer to the following. User's manual for the master/local module used 5.1 D/A Converter Module S ystem Configu[...]

44 5.2 Applicable Systems (1) Applicable master st ation When using a D/A converter module, use t he following products as a master station. When a master station other than the above is used, the D/A converter module cannot be used. (2) Connect able modules One extension mod ule can be connected to one D/A converter mo dule. (3) Ethernet cable For[...]

45 CHAPTER 6 INST ALLA TION AND WIRING 6 6.1 Station Number Setting CHAPTER 6 INST ALLA TION AND WIRING This chapter describes the installation and wiring of the D/A converter module. 6.1 S t ation Number Setting (1) Setting procedure Set the station number with the rot ary switch on the fron t of the module. T he setting value of the station numbe[...]

46 6.2 Inst allation Environment and Inst allation Position 6.2.1 Inst allation environment (1) Inst allation location Do not install the D/A converter module to the place where: • Ambient temperature is outside the range of 0 to 55°C; • Ambient humidity is outside the range of 5 to 95% RH; • Condensation occurs due to rapid temperatu re cha[...]

47 CHAPTER 6 INST ALLA TION AND WIRING 6 6.2 Installation Environment and Installation Position 6.2.3 Installation direction 6.2.3 Inst allation direction The D/A converter module can be installed in six di rections. Use the DIN rail to install the modul e. Downward installation DIN rail V ertical installation Horizontal installation Horizontal ins[...]

48 6.3 Inst allation 6.3.1 Connecting extension modules (1) Connecting procedure (2) Disconnecting procedure Disconnect the modules by reversing the procedure ab ove. ● Shut off the external power supply for the system in all phases before connecting or disconnecting extension modules. ● Lock the module joint levers securely . Failure to do so [...]

49 CHAPTER 6 INST ALLA TION AND WIRING 6 6.3 Installation 6.3.2 Mounting the modules on a DIN rail 6.3.2 Mounting the modules on a D IN rail An example of the use of the DIN rail stopper is described in the following procedure. F ix the module according to the manual of the DIN rail stopper used. (1) Mounting procedure 1. Pull down all DIN rail hoo[...]

50 Do not slide modules from the edge of the DIN rail w hen mounting them. Doing so may damage the metal part located on the back of the module. (2) Removal procedure Remove the modules from the DIN ra il by reversing the above procedure. (3) Applicable DIN rail model (comp liant with IEC 60715) • TH35-7.5Fe • TH35-7.5Al 6. Hitch the up per hoo[...]

51 CHAPTER 6 INST ALLA TION AND WIRING 6 6.3 Installation 6.3.2 Mounting the modules on a DIN rail (4) Interval between DI N rail mounting screws T ighten the screws at intervals of 200 mm or less. (5) DIN rail stopper Use a stopper that is attachable to the DIN rail.[...]

52 6.4 Wiring with T erminal Block for Module Power Supply and FG (1) T ightening torque T ighten the terminal block screws within the following specified torque range. T ightening the screws too mu ch may damage the modul e case. (2) Wire to be used The following table describes the wire to be conne cted to the terminal block for module power supp[...]

53 CHAPTER 6 INST ALLA TION AND WIRING 6 6.4 Wiring with Terminal Block for Module Power Supply and FG (4) Connecting and di sconnecting the cable T o connect the cable, insert t he wire with the cable fixing screw loosened and tighten the screw. T o disconnect the cable, pull out the wire with the cab le fixing screw loo sened with a slo tted scre[...]

54 6.5 Wiring of Ethernet Cable (1) Connecting the Ethernet cable (a) Connecting 1. Power off the power supplies of the D/A converte r module a nd the externa l device. 2. Push the Ethernet cable co nnector into the D/A converter module until it cl icks. Pa y attention to the connector's di rection. 3. Power on the module. 4. Power on the exte[...]

55 CHAPTER 6 INST ALLA TION AND WIRING 6 6.5 Wiring of Ethernet Cable ● PORT1 and PORT2 need not to be distinguished. When only one connector is used in star topology , either PORT1 or PORT2 can be connected. ● When two connectors are use d in line topology or ring topo logy , an Ethernet cable can be c onnected to the connectors in any combina[...]

56 (2) Precautions (a) Laying Ethernet cables • Place the Etherne t cable in a duct or clamp them. If not, d angling cable may swing or i nadvertentl y be pulled, resulting in damage to the module or c ables or malfunctio n due to poor contact. • Do not tou ch the core of the con nector of the cable o r the module, and protec t it from dirt an [...]

57 CHAPTER 6 INST ALLA TION AND WIRING 6 6.6 Wiring of External Device and Terminal Block 6.6 Wiring of External Device and T erminal Block (1) Tightening torque T ighten the terminal blo ck screws within the following specified torque range . Failure to secure the terminal block may cause malfu nction, failure, or drop. The following table shows a[...]

58 (b) Installation proced ure 1. Open the terminal block co ver to install the 2-piece terminal block. 2. Tigh ten the terminal bloc k mounting screws. T erminal block mounting screw[...]

59 CHAPTER 6 INST ALLA TION AND WIRING 6 6.6 Wiring of External Device and Terminal Block (3) Wiring of the external device and terminal block (a) Signal name The following shows signal names of the termin al block. Do not wire the NC terminals. Wrong wiring ma y cause the module to fail or malfun ction. Pin number Signal name 1N C 2N C 3 CH1 V+ 4C[...]

60 (b) Wiring to a terminal block The following shows wirings to a terminal block. • For the voltage output • For the current output CH4 I+ NC CH1 V+ CH1 I+ CH2 V+ CH2 I+ CH3 V+ CH3 I+ CH4 V+ NC NC NC CH3 COM CH4 COM NC CH2 COM NC CH1 COM CH1 CH2 CH3 CH4 CH4 I+ NC CH1 V+ CH1 I+ CH2 V+ CH2 I+ CH3 V+ CH3 I+ CH4 V+ NC NC NC CH3 COM CH4 COM NC CH2 [...]

61 CHAPTER 6 INST ALLA TION AND WIRING 6 6.6 Wiring of External Device and Terminal Block (c) Precautions for external wiring T o obtain the maximum performance from the functions of the D/A converter module and improve the system reliability , an externa l wiring with high durability against no ise is required. Precauti ons for external wiri ng ar[...]

62 (e) Wiring method ● Do not put oil on the terminal and screw . Failure to do so may damage the screw. ● The number of the applicable solderless terminals must be two or less. Wh en insert ing two applicable solderless terminals, insert them back-to-back. Otherwise t he screw cannot be tightened and it may damage the screw. ● T ighten the t[...]

63 CHAPTER 7 V ARIOUS SETTINGS 7 7.1 Parameter Setting CHAPTER 7 V ARIOUS SETTINGS This chapter describes the setting pr ocedures of the D/A converter module. 7.1 Parameter Setting Set the parameter of this module wi th the netw ork parameter writte n to the CPU module of the ma ster station. For the setting procedure of the master station, refer t[...]

64 (1) Precautions (a) B efore p arameter settings • Read and write the parameter settings of this m odule with the CPU module in the STOP status. Reading and writing are unavailable in the RUN status. • Check that the start I/O number of the network p arameter of the master statio n matches that of the PLC parameter . If they differ , the para[...]

65 CHAPTER 7 V ARIOUS SETTINGS 7 7.1 Parameter Setting (2) Setting procedure 1. Display the "CC IE Field Configuration" window . • When the master/local mo dule is the QJ71GF1 1- T2 Project window [Parameter] [Network Pa ra meter] [Etherne t/CC IE/MELSECNET] button • When the master/local mo dule is the LJ71GF1 1-T2 Project window [Pa[...]

66 5. Double-click the item to ch ange the setting, an d input the setting value . • Items to input from the pull-down list Double-click the item to set, to disp lay the pull-down list. Select the item. • Items to input from the text box Double-click the item to set, and input the setting value. Pull-down list type Text box type The box cannot [...]

67 CHAPTER 7 V ARIOUS SETTINGS 7 7.1 Parameter Setting Item Reference Mode switch Page 78, Section 8.2 (1) External signal assignment setting T rigger output signal assignment Page 1 18, Section 8.15 ( 3) Alert output signal assignment Error flag assignment W arning flag assignment Cyclic data update watch time setting Page 84, Section 8.7 Extensio[...]

68 6. Click the button and the following window is displayed. 7. Click the button. 8. The parameter is written to the D/A converter module. ● When using the extension module, also se t the parameter of the extension module. For the parameter of the extension module, refer to the following. Manual for the extension module used ● Set all the item[...]

69 CHAPTER 7 V ARIOUS SETTINGS 7 7.2 Changing the Parameter 7.2.1 Changing the network configuration 7.2 Changing the Parameter This section describes the procedures to change the parameter . The precautions to take when changing the parameter are same as the following. • Precautions ( Page 6 4, Section 7.1 (1 ) 7.2.1 Changing the network configu[...]

70 6. Select a D/A co nverter module in "List of st ations" on the "CC IE Fi eld Configurati on" window . 7. Open the "Parameter Processing of Slav e St ation" window . [CC IE Field Configuration] [Online ] [Parameter Processing of Slave S tation] 8. Set "Parameter read" for "Method selec tion". 9. [...]

71 CHAPTER 7 V ARIOUS SETTINGS 7 7.2 Changing the Parameter 7.2.1 Changing the network configuration 12. Set "Parameter write" for "Method selection". 13. Set "Write V alue". The following are the procedure. • Click the title cell of "Read V alue" to select all the items and copy them. • Click the title c[...]

72 19. Set the refresh parameter . Ch ange the value as necessar y . 20. Write the set p arameter to the CPU module of the master station and reset the CPU module. 21. Change the status of the CPU module of the master st ation to RUN. The network configuration setting is now completed. RESET RUN[...]

73 CHAPTER 7 V ARIOUS SETTINGS 7 7.2 Changing the Parameter 7.2.2 Changing the parameter without cha nging the network configuration 7.2.2 Changing the p arameter with out changing the network configuration T o change on ly the created module parameter of the slave station without changing th e network configuration, set the parameter in the follow[...]

74 7. The parameter is read from the D/A converter module. 8. Set "Parameter write" for "Method selection". 9. Set "Write V alue". T he following are the procedure. • Click the title cell of "Read V alu e" to select all the items an d copy them. • Click the title cell of "W rite V alue" to selec[...]

75 CHAPTER 7 V ARIOUS SETTINGS 7 7.3 Offset/Gain Setting 7.3 Offset/Gain Setting When the user range setting is used, configure the o ffset/gain setting with the fol lowing opera tions. When factory default settings are used, the offset/gain setting is not required. 1. Power off the module. 2. Set "O/G" for "x10" of th e stat io[...]

76 ● Configure the offset/gain setting in acco rdance with the actual use situation. Connection to the CC-Link IE Field Network is not re quired. ● Configure the offset/gain setting in the range satisfying the fo llowing condition. When the setting value out of the range is configured, the maximum resolution and accuracy of the modul e may not [...]

77 CHAPTER 8 FUNCTION 8 8.1 Mode Shift at Power-on CHAPTER 8 FUNCTION This chapter describes the details of the functions availa ble in the D/A converter modu le, and the setting procedures for those functions. For deta ils on remote I/O signals, remote registers, and remote buff er memory , refer to the following. • Details of Remote I/O Signals[...]

78 8.2 Drive Mode Switch The drive modes of the D/A converter module are t he normal mode, trigger out put mode, and synchronous communication mode. The following table lists the type and the operation o f the mode. The drive mode can be selected by setting Mode sw itch (address: 0000 H ). Note that the syn c hronous communication mode can be used [...]

79 CHAPTER 8 FUNCTION 8 8.2 Drive Mode Switch 4. Check that "0920 H " is stored in Latest warning code (R Wr1) . [Online] [Monitor] [Device/Buf fer Memory Batch] 5. The D/A converter mod ule start s operating in the set drive mode by turning off and on th e power or performing the remote rese t. T o operate the D/A converter module connec[...]

80 8.3 D/A Conversion Enable/Disable Function Sets whether to enable or disable D/A conversion for each channel. Disabling the D/A conversion for unused channels reduces the conversion cycles. (1) Setting procedure 1. Set "Parameter write" for "Method selection". "CC IE Field Configuration" window Select a D/ A convert[...]

81 CHAPTER 8 FUNCTION 8 8.5 Range Switching Function 8.5 Range Switching Function The output range can b e selected for ea ch channel from the followin g ranges: • Factory default range (4 to 20mA, 0 to 20mA, 1 to 5V , 0 to 5V , -10 to 10V) • User range (user range setting 1, user range setting 2) (1) Setting procedure 1. Set "Parameter wr[...]

82 8.6 Analog Output HOLD/CLEAR Function Whether to hold or clear the output analog valu e can be se t, according to the CPU module operating status (RUN, STOP , or stop error). (1) Combination of analog output st atus The following table shows how the analog outpu t status changes, depending on the combination of settings for D/A conversion enable[...]

83 CHAPTER 8 FUNCTION 8 8.6 Analog Output HOLD/CLEAR Function (2) Setting procedure 1. Set "Parameter write" for "Method selection". "CC IE Field Configuratio n" window Select a D/A converter module in "List of stations". [CC IE Field Configu ration] [Online] [Parameter Processing of Slave S tation] 2. Set &q[...]

84 8.7 Cyclic Dat a Up date W atch Function The update intervals of cyclic da ta are monitored. The last o utput value is held or cleared when the cyclic transmission stop status continues longer than the set monitoring time. The cyclic transmission stop status is the st atus that th e D LINK LED is flashing (Data link in operation (cyclic transmis[...]

85 CHAPTER 8 FUNCTION 8 8.8 Scaling Function 8.8 Scaling Function The D/A converter module scale-converts the digital value to the set rang e of the scaling u pper limit value and scaling lower limit value. The programmi ng for scale conversion can be reduced. (1) Concept of scaling setting The setting for scaling lower and upper limit val ues diff[...]

86 (3) Setting procedure 1. Set "Parameter write" for "Method selection". "CC IE Field Configuration" window Select a D/ A converte r module in "List of stations". [CC IE Field Configuration] [Online] [Parameter Processing of Slave S tation] 2. Set "CH  D/A conversion enable/disable setting" to &[...]

87 CHAPTER 8 FUNCTION 8 8.8 Scaling Function (4) Example of scaling setting Ex. 1: When values are set for a channel wi th output range of 0 to 5V as follows: •" C H  Scaling enable/disable setting": "0: Ena ble" •" C H  Scaling upper limit value": 10000 •" C H  Scaling lower limit value": 2000[...]

88 Ex. 2: When values are set for a channel with output range of -10 to 10V as follows: •" C H  Scaling en able/disable settin g": "0: Enable" •" C H  Scaling up per limit value": 12000 •" C H  Scaling lo wer limit value": 4000 The digital values and scale-converted digital values are as follow[...]

89 CHAPTER 8 FUNCTION 8 8.8 Scaling Function Ex. 3: When values are set for a channel with the user range 1 of 2 to 10V as follows: •" C H  Scaling enable/disable setting": "0: Ena ble" •" C H  Scaling upper limit value": 8000 •" C H  Scaling lower limit value": 2000 The digital values and scal[...]

90 ● When using the scaling function, the digi tal value before scaling can be set to a value out of the range of the scaling upper and lower limit values (dotted line are a in the I/O char acteristics). However, use the scaling function within the range of the analog output pra ctical range (solid line area in th e I/O characteristics). If the v[...]

91 CHAPTER 8 FUNCTION 8 8.9 Shift Function 8.9 Shif t Function Using this function, the D/A converter m odule outputs the converted digital value with the shifting set value added, in analog. When the shifting set value is changed, it is reflected to t he analog outp ut value in real time. Therefore, fi ne adjustment can be easily performed when th[...]

92 3. Set a value for CH  Shifting set value (R Ww6 to RWw9). The default value of the shifting set value is "0". If the digital value exceeds the range of -32768 to 32767 as a re sult of shift addition, the digi tal operation value is fixed t o the lower limit value (-32768) or the upper limit value (32767). (3) Setting example Ex. Wh[...]

93 CHAPTER 8 FUNCTION 8 8.9 Shift Function (4) Setting example of when both the scal ing function and shift function are used Ex. When the following settings are used for a c han nel with outp ut range of 0 to 5V : •" C H  Scaling enable/disable setting": "0: Ena ble" •" C H  Scaling upper limit value": 9000 [...]

94 1. Set "Parameter write" for "Method selection". "CC IE Field Configuration" window Select a D/ A converte r module in "List of stations". [CC IE Field Configuration] [Online] [Parameter Processing of Slave S tation] 2. Set "CH  D/A conversion enable/disable setting" to "0: Enable". [...]

95 CHAPTER 8 FUNCTION 8 8.10 Digital Value Range Check Function 8.10 Digit al V alue Range Check Function An error is output when the digital value is ou t of the digital input range for the output ra nge. (1) Notification of a check code When the digital value is greater than the upper limit of the setting range or smaller than the lower limit of [...]

96 (3) Resetting a check code The check codes can be reset by either of the following two methods. • Write a digital value within the setting range, and turn on and off Error clear request fl ag (RY A). • T urn on and off Initial data setting request flag (RY9). (4) When the scaling function is set enabled When Scaling enable/disable setti ng ([...]

97 CHAPTER 8 FUNCTION 8 8.10 Digital Value Range Check Function (6) Operation example of th e check code detection Ex. When values are set for a channel with out put range of -10 to 10V as follow s: •" C H  Scaling enable/disable setting": "0: Ena ble" •" C H  Scaling upper limit value": 24000 •" C H ?[...]

98 8.1 1 Alert Output Function This function outputs alert when a digita l value is in the range set in advance. ALM LED Latest warning code (RWr1) Remote READY (RXB) ON OFF ON OFF 0A11 H ON 0000 H 0000 H 0A01 H Alert output upper limit value OFF ON Alert output signal (RX1E) OFF OFF ON Alert output lower limit value 10000 -1000 Digital value Alert[...]

99 CHAPTER 8 FUNCTION 8 8.11 Alert Output Function (1) Alert output notification When the digi tal value is greater than t he aler t output upper limit value, or sm a ller than the alert output lo wer limit value, alert notifications are made by Alert output flag (RWrA), Alert output signa l (RX1E) and th e ALM LED turning ON. • Alert output flag[...]

100 (5) When the shif t function is set enabled When a value is set to CH  Shifting set value (RWw6 to R Ww9), the value with the shifting set value added is the target for the alert. (6) Setting procedure 1. Set "Parameter write" for "Method selection". "CC IE Field Configuration" window Select a D/ A converte r mo[...]

101 CHAPTER 8 FUNCTION 8 8.12 Trigger Output Function 8.12 T rigger Output Function Using this function, the D/A converter module performs the D/A conversion at the timing of a trigger output request. ● This function can be used only when the dr ive mode is set to the trigger output mode. ● The D/A converter module converts analog values into d[...]

102 Ex. The following figure shows th e operation until Trigger output completed flag (RX19) turns on after T rigger output request (RY19) is turned on. • 1) Once Trigger output request (RY19) is turned on, the D/A conversion starts. • 2) Th e D/A conversion in CH1 is performed and the analog output value in CH1 is updated. The D /A conversion [...]

103 CHAPTER 8 FUNCTION 8 8.12 Trigger Output Function (4) From the st art of the trig ger output to the completion Set Mode switch (address: 0000 H ) to T rigger output mode (1 H ). When Initial data setting request fla g (RY9) is turned on and off, "0920 H " is stored to Latest warning code (RWr 1). After the module is turned of f and on[...]

104 (5) T rigger output completed clear request The following describ es the trigger output completed clear request. (a) T rigger output completed clear request The following figure shows the operation whe re T rigger ou tput completed flag (RX19) turns off by turning on T rigger output complete d clear request (RY1A). Even when T rigger output com[...]

105 CHAPTER 8 FUNCTION 8 8.12 Trigger Output Function (6) CH  Output enable/disable flag The following descri bes T rigger output request (RY19) and CH  Output enable/d isable flag (RY10 to RY13). • When T rigger output request (RY19) is turned on while CH1 Output enable/disable flag (RY10) is set to disabled, the D/A conversion is performe[...]

106 (8) Response time The following describes the response time until Trigger out put completed flag (RX19) turns on after the trigger output is requested. (a) When T rigger output request (R Y19) is assigned to Remote input (RX) using the external signal assignment function (Response time of the D/A converter module) *1 + (Response ti me of the ex[...]

107 CHAPTER 8 FUNCTION 8 8.12 Trigger Output Function (b) When T rigger output request (R Y19) is not assigned to Remote input (RX) using the external signal assignment function The following lists the input interval, ON time, and OFF time of T rigger output request (RY19). *1 SM: Sequence scan time [ms] ( User's manual fo r the CPU module use[...]

108 (10)Setting procedure 1. Set "Parameter write" for "Method selection". "CC IE Field Configuration" window Select a D/ A converte r module in "List of stations". [CC IE Field Configuration] [Online] [Parameter Processing of Slave S tation] 2. Set "Mode switch" to "1: T rigger output mode&quo[...]

109 CHAPTER 8 FUNCTION 8 8.13 CC-Link IE Field Network Synchronous Communicatio n Function 8.13 CC-Link IE Field Network Synchronous Communication Function With this function, the D/A converter module can perform D/A conversio n synchronized with the opera tion cycle of a simple motion module. This enables the D/A converter module to operate at the[...]

110 (3) Operation using the CC-Link IE Fi eld Network synchronous communication function Every operation cycle of the simple motion module, the D/A conversion is performed for the D/A conversion enabled channels. Controlled by the D/A converter module D/A conversion process D/A conversion D/A conversion D/A conversion Digital value Digital value Di[...]

111 CHAPTER 8 FUNCTION 8 8.13 CC-Link IE Field Network Synchronous Communicatio n Function Ex. The following figure shows an example of the op eration timing of when D/A conversion is enabled for all channels. No. Description 1) The D/A conversion is started when the operation of the simple motion module shifts to the next cycle. 2) The D/A convers[...]

112 (a) S B/SW signals used with the CC-Link IE Field Network synchro nous communication function T o check the operating status of t he D/A converte r module (synchronous or asynchronous), use the followin g link special register (SW) on the master station. • Synchronous/asynchronous operation status in formation (each station) (SW01C8 to SW01CF[...]

113 CHAPTER 8 FUNCTION 8 8.13 CC-Link IE Field Network Synchronous Communicatio n Function (5) Setting procedure (D/A converter module) 1. Select a D/A converter modu le in "List of stations " on the "CC IE Field Configuration" windo w , and set the values as follows. • Set 17 or larger number in "ST A#". • Set 32 [...]

114 8.14 Error Notification Function When an error , warning, or alarm o ccurs, the D/A converter module notifi es the master station of it using remote input signals and remote registers. Remark The notification of the error , warning, or alarm can be checked on t he LED on the front of the module. For details, refer to the following. • P ART NA[...]

115 CHAPTER 8 FUNCTION 8 8.14 Error Notification Function *1 A warning is in the following state five seconds after the error cause is removed. • Warning flag (RX7) turns off. • Latest warning code (RWr1) is cleared. • The ERR. LED turns off. *2 The alarm is not automatically cleared. Latest warning code (R Wr1) is cleared when the other mino[...]

116 (3) Method for clearing an error by execut ing the command of the slave st ation The following shows how to clear an e rror by executi ng the command of the slave station. Moderate errors and Out-of-range digital value can be cleared. 1. Select the D/A converte r module in "List of s t ations" on the "CC IE Field Configu ration&q[...]

117 CHAPTER 8 FUNCTION 8 8.15 Function at the Extension Module Installation 8.15 Function at the Extension Module Inst allation One extension I/O modul e can be connected to one D/A conve rter module. Remote I/O signals of the D/A converter module can be assi gned to input signals of the connected extension input module or o utput signals of the co[...]

118 (3) External signal assignment function Remote input signals or remote output signals of the D/A converter module can be assigned to I/O signals of the connected extension I/O module. Signal s can be inpu t fr o m the extension I/O module and error signals can be output to the e xternal at the fixed timing wi th out influence from the seque nce[...]

119 CHAPTER 8 FUNCTION 8 8.15 Function at the Extension Module Installation (4) Setting procedure Ex. When setting the assignment explai ned in the previous page 1. Set "Parameter write" for "Method selection". "CC IE Field Configuratio n" window Select a D/A converter module in "List of stations". [CC IE Fie[...]

120 (a) O peration of when an error occurs Depending on whether the remote I/O signals of the ex tension I/O module are used as general-purpose I/O signals or assigned for the external signal assig nment function, the operation of the D/A converter modu le for an error differs as shown in the following table. *1 When the external signal assignment [...]

121 CHAPTER 8 FUNCTION 8 8.16 CC-Link IE Field Network Diagnostic Function 8.16 CC-Link IE Field Network Diagnostic Function With this function, whether an y network error occurs or not can be checked through GX Works2 connected to the CPU module. (1) How to use 1. Connect GX Works2 to the CPU mod ule. 2. St art CC-Link IE Fiel d Network diagnos ti[...]

122 *1 "Selected S tation Communication S tatus Monitor", whic h appears at the bottom right in the window , indicates the communication status of the D/A converter module. F or the error and alarm for the D/A conver ter module, refer to the following. • Checking for the Error Codes and the Alarm Codes ( Pag e 135, Section 1 1.1) Some o[...]

123 CHAPTER 8 FUNCTION 8 8.16 CC-Link IE Field Network Diagnostic Function (a) Remote operation 1. Select a slave statio n to be reset and click the button. 2. Clicking the button on the following window start s the remote reset. 3. Click the button on the following win dow .[...]

124 CHAPTER 9 PROGRAMMING This chapter describes the progra mmi ng of the D/A converter module. 9.1 Precautions for Programming This section describes precautions to cr eate CC-Link IE Field Netw ork programs. (1) Cyclic transmission program For a cyclic transmission program, inte rlock with the following link special relay (SB) and link speci al r[...]

125 CHAPTER 9 PROGRAMMING 9 9.2 Procedure for Programming 9.2 Procedure for Programming Create a program to execute D/A conversion , according to the following proced ure. 9.3 Program Example (1) System configuration Start End Parameter setting ( ) Error reset program Auxiliary program* 1 *1 A program that is added according to the control target ([...]

126 (a) Link device assignment X1000 to X100F Y1000 to Y101F X Y W W CPU module RX00 to RX0F RY00 to RY1F RWw0 to RWwF RX RY RWw RWr Master/local module Remote device station (Station No.1) X1020 to X102F RX20 to RX2F Main module (D/A converter module) Extension module (extension output module) Master station (Station No.0) RX RWr0 to RWrF W1000 to[...]

127 CHAPTER 9 PROGRAMMING 9 9.3 Program Example (2) Programming condition This program enable s the D/A conversion in C H1 and CH 2 of the D/A converte r module and outputs the written digital values in analog. If an error or alert occurs, a digital signal is output from the extension output module. (3) Initial setting description Set the initial v[...]

128 (4) Device for user Device Description X20 Digital value write command QX10 (X20 to X2F) X22 Batch analog output enable command X24 Alert outp ut clear command X26 Error clear command X28 Che ck code clear command X1007 W arning flag NZ2GF2B-60DA4 (X1000 to X101F) X1009 Initial data setting completed flag X100A Error flag X100B Remote READY X10[...]

129 CHAPTER 9 PROGRAMMING 9 9.3 Program Example (5) Setting procedure Connect GX Works2 to the master station to configure the setting. 1. Create a project o n GX Works2. Select "QCPU (Q mode)" for "PLC Series" and select "Q10UDH" for "PLC T ype". [Project] [New ...] 2. Display th e network p arame ter settin[...]

130 3. Display the "CC IE Field Config uration" window and co nfigure the configur ation and station number of the slave station as follows. button 4. Close the "CC IE Fi eld Configurati on" window . [CC IE Field Configuration] [ Close with Refle cting the Settin g] 5. Display the refresh parameter setting window and configu re [...]

131 CHAPTER 9 PROGRAMMING 9 9.3 Program Example 7. Display the "Parameter Proc essing of Slave St ation" window . Project window [Parameter] [Netw ork Parameter] [Ethernet/CC IE/MELSECNET] button Select a D/A converter module in "List of stations ". [CC IE Field Configuration] [On line] [Parameter Processing of Slave S tation] 8[...]

132 (6) Program example 1. Create the following program with GX Works2. 2. Write the program to the CPU module of the ma ster station and reset the CPU mod ule, or turn on from off the power supply . 3. Change the status of the CPU module of the master st ation to RUN. If the master station does not receive a response for several li nk scans from t[...]

133 CHAPTER 10 MAINTENANCE AND INSPECTION 10 CHAPTER 10 MAINTENANCE AND INSPECTION The D/A convert er module has no specia l item to be inspecte d. However , to maintain the best condition of the system, perform the inspection in a ccordance with the items descr ibed in the user's manual of the CPU module used.[...]

134 Memo[...]

135 CHAPTER 1 1 TROUBLESHOOTING 11 11.1 Checking for the Error Codes and the Alar m Codes CHAPTER 1 1 TROUBLESHOOTING This chapter describes errors that may occur while th e D/A converter module is used, and those troublesho oting. 11 . 1 Checking for the Error Codes and the Alarm Codes Error codes can be checked by any of the follow ing methods: ?[...]

136 ● The error history registers 15 errors at a maximum. If 16 or more er rors occur , errors are deleted from the oldest. ● If the same error occurs continuously , the error that occurred first is stored to the error history . ● Even after the power of the module is turned off and on, the error history remains. ● T o initialize the error [...]

137 CHAPTER 1 1 TROUBLESHOOTING 11 11.1 Checking for the Error Codes and the Alar m Codes (2) Checking by Latest error code (RW r0) Check the error with the remote regi ster of the mast er/local module. [Online] [Monitor] [Device/Buf fer Memory Batch] Ex. When the refresh target device for Latest error code (RW r0) is W1 100 (3) Checking by Latest [...]

138 11 . 2 Error Code List This section describes error codes. Error codes are classified by error number as follows. (1) Error code list (0000 H to 3FFF H D529 H D52B H ) The errors are classifi ed into the following three types. If an error occurs, check that the D LINK LED is on. Then take corrective actions as listed below . Error code Classifi[...]

139 CHAPTER 1 1 TROUBLESHOOTING 11 11.2 Error Code List 0130 H Moderate error Non-volatile memory data error (parameter) The parameter data stored in the non-volatile memory are abnormal. • Set no request (0), request (1), and no request (0) in Parameter information clear request (address: 1002H) and set the parameters of the non-volatile memory [...]

140 060  H *1 Minor error Digital value outside the range The value set in CH  Digital value (RWw2 to RWw5) is outside the range.  represents the channel number where an error has occurred. Set the value of CH  Digital value (RWw2 to RWw5) within the allowable range. 062  H *1 Moderate error Alert output upper/lower limit value inver[...]

141 CHAPTER 1 1 TROUBLESHOOTING 11 11.2 Error Code List 0950 H Moderate error Clock data outside the range The clock data acquired from the CPU module is invalid. There may be an influence fr om noise or a hardware error . If the same error occurs again even after measures have been taken against noise, please consult your local Mitsubishi represen[...]

142 *1 Set a value within the allowable range. Then per form one of the following operations to clear the er ror . *2 Mode switch setting change (error code: 0920 H ) is not cleared even if five seconds have passed after the error occurred. During the error , the D/A converter module keeps operating in the mode befor e the Mode switch (address: 000[...]

143 CHAPTER 1 1 TROUBLESHOOTING 11 11.2 Error Code List (2) Error code list (D000 H to DFFF H (D529 H and D52B H excluded)) When an error occurs, the ERR. LED does not turn on. The D LINK LED flashes or turns off. T roubleshoot the problem with the CC-Link IE Fiel d Network diagnostics. ( Page 121, Section 8.16) When multiple errors occur , only th[...]

144 11 . 3 Alarm Code List This section lists alar m codes. Alarm code (hexadecimal) Category Nam e Description and cause of alarm Action 0A  H Minor error Alert occurrence An alert is occurring. The channel where the alert has occurred fits in  . A value fits in indicates that the alarm status is as follows: 0: Upper limit of an alert 1: Low[...]

145 CHAPTER 1 1 TROUBLESHOOTING 11 11.4 Checking the LEDs 11 . 4 Checking the LEDs This section describes how to troubleshoot the system by the LEDs. For the troubleshooting using the LEDs of the ex tension I/O module, refer to the following. CC-Link IE Field Network Remote I/O Module Use r's Manual (1) When the PW LED does not turn on (2) Whe[...]

146 (5) When the D LINK LED turns off (6) When the D LINK LED flashes Check item Action Does the own station in network operate normally? Connect GX Works2 to the master station, and check if the own station is performing data link by CC-Link IE Field Network diagnostics. ( User's manual for the master/local module used) Are 1000BASE-T -compli[...]

147 CHAPTER 1 1 TROUBLESHOOTING 11 11.4 Checking the LEDs (7) When the L ER LED turns on (8) When the LINK LED turns off (9) When the ERR. LED turns on (10)When the ALM LED turns on Check item Action Are Ethernet cables normal? • Check if 1000BASE-T -compliant Ethernet cables are used. ( User's manual for the master/local module used) • Ch[...]

148 11 . 5 Unit T est Run a unit test to check if there is any abnormality in the D/A conver ter module. Remark When unit test fails, the error details can be checked in the error history in GX Works2. T o check the error history with GX Works2, set the st ati on number of the D/A converte r module and connect the module to the master station with [...]

149 CHAPTER 1 1 TROUBLESHOOTING 11 11.6 Troubleshooting for Each Phenomenon 11 . 6 T roubleshooting for Each Phenomenon This section describes troubl eshooting for each phenomenon. Perform troubleshoo ting for each phenomenon when the D/ A converter module d oes not operate properly with no error . When an error occurs in the D/A converter module, [...]

150 (3) When the output st atus of the extens ion output module di ffers from the link device st atus of the master station (4) When p arameters cannot be read or written with GX Works2 and CC-Link IE Field Network diagnosti cs cannot be performed Check item Action Is the setting of the ex ternal signal assignment function correct? Check that the f[...]

151 APPENDICES A Appendix 1 Details of Remote I/O Signals Appendix 1.1 Remote input signals APPENDICES Appendix 1 Det ails of Remote I/O Signals This section describes the details of remote I/O signals assigned to the master/local mo dule. The assignment of each device number is fo r the case when the remote I/O sign als of the main module are assi[...]

152 (2) Initial dat a settin g completed flag (RX9) T urn on Initial data setting req uest fl ag (RY9) after writing parameter data to the remote buf fer memory with the REMTO instruction. This signal turns on when the operati ng condition is changed. When the following setti ngs are changed, the signal is used as an interlock condition to turn Ini[...]

153 APPENDICES A Appendix 1 Details of Remote I/O Signals Appendix 1.1 Remote input signals (3) Error flag (RXA) This signal turns on when a moderate or major erro r occurs. T o clear Late st error code (RW r0), turn on and off Error clear request flag (R Y A). • When a mode rate error occu rs • When a major error occurs (a) Error history The e[...]

154 (4) Remote READY (RXB) This signal is used as a n interlock condition when the ma ster station reads/writes data to/from the re mote register or remote buffer memory areas of the D/A converter module. The signal turns on when the module power supply is turned on. When Error flag (RXA) turns on, the signal turns off. (5) T rigger output complete[...]

155 APPENDICES A Appendix 1 Details of Remote I/O Signals Appendix 1.1 Remote input signals (6) Alert output signal (RX1E) If the digital value in any D/A conversion enabled channe ls becomes any of the following status, this signal is turned on. • Digital value > Al ert output upper limit value • Digital value < Al ert output lower limit[...]

156 Appendix 1.2 Remote output signals (1) Initial dat a settin g request flag (R Y9) T urn on this signal after writing parame ter dat a to the remote buffer memory . Initial data setting completed flag (RX9) turns on when the operating con dition is changed. For the on and off timing, refer to the following. • Initial data setting completed fla[...]

157 APPENDICES A Appendix 1 Details of Remote I/O Signals Appendix 1.2 Remote output signals (7) External power supply m onitor request flag (R Y1F) T urn on this flag to activate the external pow er supply monitoring function. For the on and off timing , refer to the following. • External power supply monitor state flag (RX1F) ( Page 155, Append[...]

158 Appendix 2 Details of Remote Register Areas This section describes the details of remote register areas for communications with the master/local module. The assignment of each device number is for the case when the remote registers of the main modul e are assigned to RWr0 to R WrF and RWw0 to R WwF . (1) Latest error code (R Wr0) An error code [...]

159 APPENDICES A Appendix 2 Details of Remote Register Areas (a) Resetting set value check codes The check codes can be reset in the following two procedures: • Write a digital value within the setting range, and turn on and off Error clear request flag (RY A). • T urn on and off Initial data setting request flag (RY9). (b) Default value Within[...]

160 (5) CH  Digit al value (RWw2 to R Ww5) On this area, the digital value for D/A conversion is written, i n signed 16-bit binary , from the CPU module. *1 The setting range and the actual range of when the scali ng function is enabled depend on the settings in the scalin g upper limit value and the scaling lower limit value. (a) When a value o[...]

161 APPENDICES A Appendix 2 Details of Remote Register Areas (6) CH  Shif ting set value (RWw6 to R Ww9) Set the shifting set value that is to be used for the sh ift function in signed 1 6-bit binary . The digital value with shift addition is D/A converted. For details on the shift function, refer to the following. • Shift Fu nction ( Page 91,[...]

162 Appendix 3 Details of Remote Buffer Memory Areas This section describes the details of remote buf fer memory areas of the D/A converter module. (1) Mode switch (address: 0000 H ) Set the mode for all cha nnels. When a value other than the a bove is set, the error code (0 730 H ) is stored in Latest error code (RWr0), Error flag (RXA) and the ER[...]

163 APPENDICES A Appendix 3 Details of Remote Buffer Memory Areas (2) T rigger output signa l assignment (address: 0002 H ) Assign T rigger output request (RY19) to Remote input (RX) of the extension input module u sing the external signal assignment function. When assigned Remote inp ut (RX) is turned on, the D/A con verter module performs the D/A[...]

164 (3) Alert output signal assignment (address: 0004 H ) Assign Alert output signal (RX1E) to Remote output (RY) of the extension output module usin g the external signal assignment function. When an alert occurs, assigned Remote output (RY) turns on. (a) S etting range The remote output (RY) number of the extension module, which is counted from t[...]

165 APPENDICES A Appendix 3 Details of Remote Buffer Memory Areas (4) Error flag assignment (address: 0005 H ) Error flag (RXA) is assigned to the remo te output (RY) of th e extension output module using th e external signal assignment function. When a moderate or major erro r occurs, the assigned remote output (RY) turns on. (a) Setting range The[...]

166 (5) W arning flag assignment (address: 0006 H ) W arning flag (RX7) is assigned to the remote output (RY) of the extension output module using the external signal assignment function. When a minor error occurs, the assigned remote output (RY) turns on. (a) S etting range The remote output (RY) number of the extension output module, counted from[...]

167 APPENDICES A Appendix 3 Details of Remote Buffer Memory Areas (6) Cyclic dat a up date watc h time setting (address: 0007 H ) This signal is used to set the time to monitor the dat a update interval of the cyclic transmissi on (watch time). When the cyclic transmission remains stopp ed longer than th e cyclic data update watch time, the D/A co [...]

168 (8) Digit al output HOLD/CLEAR setting (address: 001 1 H ) The output HOLD/CLEAR status of the extensi on outpu t module is set. For the output HOLD/CLEAR setting function, refe r to the following. CC-Link IE Field Network Remo te I/O Module User's Manual (a) E nabling the setting T urn on and off Initial data setting request flag (RY9). ([...]

169 APPENDICES A Appendix 3 Details of Remote Buffer Memory Areas (10)Range setting (address: 0103 H ) The output range is set for each channel. (a) Enabling the setting T urn on and off Initial data setting request flag (R Y9). (b) Default value The default valu e is set to 4 to 20mA (0 H ). If data other than the above is set, an error occurs. Th[...]

170 (12)Alert output set ting (address: 0105 H ) The alert output enable/disable status is set for each channel. (a) E nabling the setting T urn on and off Initial data setting request flag (RY9). (b) Default value The default value is set to Disable (1) for all channels. (13)CH  Alert output upper li mit value (address: 0106 H , 0108 H , 010A H[...]

171 APPENDICES A Appendix 3 Details of Remote Buffer Memory Areas (14)Scaling enable/disab le setting (address: 010E H ) The scaling enable/disable status is set for each channe l. For details on the scaling function, refer to the fo llowing. Scaling Function ( Pa ge 85, Section 8.8) (a) Enabling the setting T urn on and off Initial data setting re[...]

172 (16)Error history  (address: 0A00 H to 0AEF H ) Up to 15 errors occurred in the module are stored. The following shows the contents stored in Error history 1 (address: 0A00 H to 0A0F H ). *1 Those are values when the second error occurs at 13:30:50, September 1st, 2012. *2 The clock information of the error that occurred is based on the cloc[...]

173 APPENDICES A Appendix 3 Details of Remote Buffer Memory Areas (17)Error history clear command (address: 1000 H ) This command is used to clear the error hi story stored in the nonvol atile memory . (a) Clearing the error history The error history is cleared when C ommanded (1) is set to this area. (b) Default value The default valu e is set to [...]

174 (a) I nitializing the p arameter area The parameters stored in a nonvolatile memory are set ba ck to their defa ult values when Comma nded (1) is set in this area. (b) Default value The default value is set to Not commanded (0). Even if Parameter area initialization command (address: 1002 H ) is executed , the following remote input signals are[...]

175 APPENDICES A Appendix 3 Details of Remote Buffer Memory Areas (21)Module operation information in itialization command (address: 1004 H ) This command is used to clear the module operatio n information stored in the nonvol atile memory . The module operation in formation can be i nitialized only when Nonvol atile memory data error (module opera[...]

176 Appendix 4 I/O Conversion Characteristic of D/A Conversion The I/O conversion characteristics of D/A conversion are the gradient of a straight line co nnecting an offset value and a gain value when a digital value written from the CPU mo dule is converted to an analog output value (voltage or current output). (1) Offset value An analog output v[...]

177 APPENDICES A Appendix 4 I/O Conversion Characteristic of D/A Conversion (3) V olt age output characteristics The following graph shows the voltage output characteristics. *1 Set the offset value and gain value in the user range setti ng with in the range satisfying the following two conditions. • Setting range: -10 to 10V • ((Gain value) - [...]

178 (4) Current output characteristics The following graph shows th e current output characteristics. *1 Set the offset value and gain value in the user range sett ing w ithin the range satisfying the following two co nditions. • Setting range: 0 to 20mA •((Gain value) - (Offset value))  1 1.4mA Use the value within the practical digi tal in[...]

179 APPENDICES A Appendix 5 Accuracy of D/A Conversion Appendix 5 Accuracy of D/A Conversion The accuracy is measured for the maximum analog outp ut value. Even if the offset/gain setting or output range is changed to change o utput characterist ics, the accuracy remains the same, and is kept with in the range d e scribed in performance specificati[...]

180 Appendix 7 EMC and Low V olt age Directives Compliance to the EMC Directive, which is one of the EU Direc tives, has been a legal oblig ation for the p roducts sold in European countries since 1996 as well as the Low V oltage Directive since 1997. Manufacturers who recognize their products are compliant to the EMC and Low V oltage Directives ar[...]

181 APPENDICES A Appendix 7 EMC and Low Voltage Directives Appendix 7.1 Measures to comply with the EMC Directive (b) Immunity requirement s *1 The module is an open type device (a device designed to be housed in othe r equipment) and must be installed inside a conductive control panel. The tests were conducted with t he programmable controller ins[...]

182 (2) Inst allation in a control p anel The module is open type devices and mu st be installed inside a control panel. This ensures safety as well as effective shielding of programmable controlle r-gene rated electromagnetic noise. (a) C ontrol p anel • Use a conductive control panel. • When securing the top or bottom plate using bolts, co ve[...]

183 APPENDICES A Appendix 7 EMC and Low Voltage Directives Appendix 7.1 Measures to comply with the EMC Directive (3) Cables Use shielded cables for the cables which ar e connected to the module and run out from the control panel. If a shielded cable is not used or not grounded corre ctly , the noise immunity will not meet the specified value. (a) [...]

184 (5) Others (a) Ferrite core A ferrite core has the effect of reducing radiated noise in the 30MHz to 100MHz band. It is recommended to attach ferrite cores if shielded cables coming out of the control panel d o not provide sufficient shielding effects. Note that the ferrite cores must be attached at the positi on closest to the cable hole insid[...]

185 APPENDICES A Appendix 7 EMC and Low Voltage Directives Appendix 7.2 Requirements to compliance with the Low Voltage D irective Appendix 7.2 Requirements to compliance with the Low V oltage Directive The module operates at t he rated voltage of 24VDC. The Low V oltage Directive is not applied to the modules th at operate at the rated voltage of [...]

186 Appendix 8 Checking Serial Number and Function Ve r s i o n The serial number and function version of the D/A conve rte r mo dule can be checked on the rating pla te on the side of the module. See instruction manual. MODEL SERIAL MADE IN JAPAN Serial number Function version Relevant regulation standards MAC address[...]

187 APPENDICES A Appendix 9 Addition and Change of Functions Appendix 9.1 Additional function Appendix 9 Addition and Change of Functions Appendix 9.1 Additional function The following table lists the function added to the D/A co nverter module and GX Works2 and the serial number and software version of the products that support the add itional fun[...]

188 The following are the conditions when communications to the master station are not established af ter power-on of the D/A converter module. • T he Ethernet cable is not connected correctly at power-on. • T he network parameter written to the CPU module is not correct. • C ommunications to the master station failed because of noise.[...]

189 APPENDICES A Appendix 10 External Dimensions Appendix 10 External Dimensions The following shows the external dim ensions o f the D/A converter mod ule. (Unit: mm) DIN rail center 23 4 68 50 4.5 133 (74.5)[...]

190 INDEX Symbols +/- button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 A Alarm code list . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Alert output clear request flag (RY1E) . . . . . . . . . 156 Alert output flag (RWrA) . . . . . . . . . . . . . . . . . . . 159 Alert output function . . . . . . . . . . . . . . . . . [...]

2 4 I 7 8 191 Installation environment . . . . . . . . . . . . . . . . . . . . . 46 Installation environment and installation position . . . 46 Installation position . . . . . . . . . . . . . . . . . . . . . . . . 46 L L ER LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Latest error code (RWr0) . . . . . . . . . . . . . . . . [...]

192 REVISIONS *The manual number is given on the bottom left of the back cover . Japanese manual version SH-081 1 1 1-B © 2012 MITSUBISHI ELECTRIC CORPORA TION Print date *Manual number Revision November , 2012 SH(NA)-081 1 12ENG-A First edition December , 2013 SH(NA)-081 1 12ENG-B Addition of the trigger output function and C C-Link IE Field Netw[...]

193 W ARRANTY Please confirm the following produ ct warranty details before using this product. 1. Gratis W arranty T erm and Gratis W arranty Range If any faults or defects (hereinafter "Failure") found to be the responsib ility of Mitsubishi occurs during use of the product within the gratis warranty term, the product shall be repaired [...]

194 Microsoft, Windows, Windows Vist a, Windows NT , Windows XP , Windows Server , Visio, Excel, PowerPoint, Visual Basic, Visual C++, and Access are either registered trademarks or trademarks of Microsoft Corpor ation in the United S tates, Japan, and other countries. Intel, Pentium, and Celeron are trad emarks of Intel Co rporation in the United [...]

[...]

SH(NA)-081 1 12ENG-B(1 312 )MEE MODEL: CCIEF-DA-U-E MODEL CODE: 13JZ81 Specifications subject to change without notice. When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission. HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPA[...]