Mitsubishi Trim 110 manuel d'utilisation

This guide describes the operation of the dual band GSM telephones Trium 110. Edition 1, 2002. © Mitsubishi Electric Telecom Europe, 2002 Whilst every effort has been made to ensure the accuracy of the instructions contained in this guide, Mitsubishi Electric reserves the right to make improvements and changes to the product described in this guid[...]

Table of contents 2 1. Introduction ................. 3 SAR ...................................... 3 General safety ...................... 4 Vehicle safety ....................... 4 Emergency calls ................... 5 Care and maintenance ......... 5 AC/DC adaptor chargers ...... 6 Battery use ........................... 6 Your responsibility ...[...]

3 I n t r o d u c t i on Introduction Thank you for purchasing the Trium 110 dual band mobile telephone. The phone version you have bought is either the Trium 110, the Trium 110 m or the Tri- um 110 p. Please check the version on the box label. The mobile telephone de- scribed in this guide is approved for use on all GSM 900/1800 networks. Some ser[...]

4 There are a number of independent sources of information available to us- ers including: Royal Society of Canada : www.rsc.ca The International Commission on Non- Ionizing Radiation Protection (ICNIRP): www.icnirp.de The US Food and Drug Administration : www.fda.gov/cdrh/ocd/mobil- phone.html The World Health Organization : www.who.int/emf Mitsub[...]

5 I n t r o d u c t i on • If incorrectly installed in a vehicle the operation of mobile telephones can interfere with the correct operation of the vehicle electronics, such as ABS anti-lock brakes or air bags. To avoid such problems ensure that only qualified personnel carry out the installation. Verification of the pro- tection and operation of[...]

6 AC/DC adaptor chargers This apparatus is intended for use only when supplied with power from AC/DC adaptor chargers (FZ14130070, FZ14130060, FZ14130050, FZ14130080, FZ14130090 or FZ14130100). Use of any other charger or adaptors will invalidate any approval given to this apparatus and may be dangerous. Battery use You can charge a battery hundred[...]

7 I n t r o d u c t i on Key) code, obtainable only from your service provider. PUK and PUK2 codes (8 digits) Obtain the PUK code from your service provider. Use it to unblock a disabled SIM card (see page 37). The PUK2 code is required to un- block the PIN2 code (see above). Call barring password (4 digits) This password is used to bar various typ[...]

8 The phone at a glance Graphic display Telephone numbers, menus, messages, etc. are displayed here. On/Off, END key ( ) . Hold down to turn the phone on/off. Press to end a call or return to stand-by. Alphanumeric keys, - , , . To enter numbers, characters and punctuation marks. Press and hold to call the voice mail number. Press and hold to keys [...]

9 I n t r o d u c t i on Graphic display The display shows icons, alphabet characters, num- bers, menu list and instructions to the user. Use the cursor keys to navigate to the phone book, Internet/WAP™ and the menu. The rest of this guide gives you the procedures to access these func- tions. Icons in the display are described on pag e 9. Underst[...]

10 Getting started In order to become familiar with the phone quickly, follow these simple steps. Preparing to make your first call Inserting the SIM card Unpack the phone and insert the SIM card into the holder, as shown below, with the gold contacts fac- ing down. Fitting the battery Connect the battery as shown be- low. Placing the battery cover[...]

G e tt i n g s t a r t e d 11 Stand-by display From the stand-by display: See page 37 to set the time and date. Holding your phone Making a call The phone can make and receive calls only when it is switched on, unlocked (see pag e 15), has a valid SIM card inserted and has GSM net- work service coverage. If the phone cannot find a valid network the[...]

12 The phone rings and the call con- nects like a normal telephone. A call timer appears. You can also get the following mes- sages if the call does not connect or you use the second line: If the dialled number matches one stored in the phone book then the name of the called person appears in the display. Receiving a call The phone rings (or vibrat[...]

G e tt i n g s t a r t e d 13 warning tone sounds. If you are on a call, terminate the call and turn off the phone by pressing and holding down . Recharge the battery as shown be- low or swap it for a charged one. Do not turn off the phone by removing the battery , data can be lost. Charging the battery To ensure a long life for your bat- tery, re-[...]

14 SIM card Inserting the SIM card Please refer to page 10. Removing the SIM card Remove the SIM card as shown be- low.[...]

15 U s i n g y ou r p hon e Using your phone For turning on/off the mobile and mak- ing/receiving calls, see pages 10 to 12. Please note that all setting instructions described in this user guide are to be followed from the idle screen. Standby display Keypad lock To prevent accidental operation of the phone, turn on keypad lock. You can still answ[...]

16 Press Read to select the type of mes- sage you want to read. Press Select or to view the message. Dialling from memory You can dial any number stored in the SIM, or the phone memory. To do this: from the phone book from the calls log memory list The phone stores the last 10 num- bers dialled, the last 10 unanswered call numbers (if available) an[...]

17 U s i n g y ou r p hon e Silent and vibrate alert modes To avoid disturbing others you can si- lence the incoming ring and alert tones. Turning on is displayed when the silent alert mode feature is activated. is displayed when the Vibrate or Vibrate then Ring features are activated. Turning off Hands free features When you want to share your cal[...]

18 piece and sent immediately. Automatically To send a consecutive string of DTMF tones during a conversation: Pause feature You can enter and store telephone numbers and a sequence of DTMF tones together as long as you separate them by a 'pause'. To enter a pause between numbers, press and hold down . The letter p appears. The phone can [...]

19 U s i n g y ou r p hon e Action when receiving a second call You hear a 'double beep' when your phone receives a second call. An an- imated phone icon and the tele- phone number (if available) also appear. To accept the second call To reject the second call: To swap between the two connect- ed calls: Multi-party or conference calls (ne[...]

20 The menu Use the round cursor key to access the menu system. Your menu options can vary. Some may not appear. This de- pends on your network operator and your subscription, plus on the phone version you have (check on box label). Access to the menus Press to view all stored telephone numbers. Press to enter the main menu. Hold down Exit or press[...]

T h e m e nu 21 text entry or Multitap text entry.Press to swap between T9 text entry and the Multitap method. To enter text with T9: Tips and operation Example To enter Card in the display: • Press and select Messages . • Select Write new . • Press : appears. • Press . A appears. • Press . Ca appears. • Press . Car appears. • Press .[...]

22 Example To enter Card in the display: • Press and select Messages . • Select Write new . • Press and hold until appears. Press briefly three times, C appears. • Wait for the available characters to go from the display, press and hold until appears. Press briefly once, a appears. • Press briefly three times, r appears. • Press briefly[...]

T h e m e nu 23 number. This ensures that the number can also be dialled from abroad. There are several ways to store numbers into the phone or SIM memory: Phone memory • Directly from the stand-by dis- play: • Using the menu: • From last dialled, received and unanswered lists: SIM phone book memory You can enter the SIM memory from the stand[...]

24 • Using the menu: • From other stored locations Numbers stored in the last dialled, received, unanswered, scratchpad and SMS message locations can all be stored in the phone book: A warning message appears when selecting the phone book when the SIM or phone memory is full. Free space in the phone book To see the remaining free space in the S[...]

T h e m e nu 25 Own number You can store your main 'Line 1' voice mobile number, your voice mobile number for Line 2 (Alternate Line Service) and your data and fax numbers into the SIM card. You can enter them manually and name them (e.g: Line 1 'Office'. To view, name and edit your own display number(s): Fixed dialling numbers [...]

26 Messages (SMS) You can exchange short text messages of up to 160 characters with other mo- bile phones with SMS. You can also store, edit and forward messages and save any of the numbers they contain. Reading a received SMS message When the phone receives an SMS message a new SMS alert tone sounds and appears. The SIM stores the message. If flas[...]

T h e m e nu 27 not have this number, ask your service provider for it. If required you can also choose the validity period, format, paid reply request and request a delivery re- port. Default settings are assumed if not set. Creating a draft text Parts of a message are often the same, such as the greeting or signa- ture. To save time, you can crea[...]

28 Storing a new SMS message Modifying and re-sending messag- es in the outbox The outbox contains unsent draft messages, stored sent messages and sent but undelivered messages. You can modify and re-send these as new messages. To select an outbox message: Status request on sent messages If you request the status of a deliv- ered message the delive[...]

T h e m e nu 29 phone uses it by default. Otherwise select the template you want when sending a message. Storage consumption To consult the memory used by SMS: EMS 1 EMS stands for Enhanced Message Se- vice. This feature allows to receive mes- sages with text, melodies, images and animated icons. These messages are sent via the Internet; they may b[...]

30 If the caller’s number is not availa- ble, Unknown number appears (unanswered and received lists). Pressing while on a displayed number calls that number. Pressing Options accesses the following menu: Use or to select the required option and follow the display prompts. Press and hold Exit or to re- turn to the stand-by display. Call times Call[...]

T h e m e nu 31 Reminder - Call duration You can set a call duration reminder in multiples of 1 minute (1 - 59 min.) intervals. It beeps at the set intervals. Call timer - reset To reset all the call timers, you need the 4 digit phone lock code. Call costs management (subscrip- tion service only) An Advice of Charge (AoC) subscrip- tion service sho[...]

32 Show costs Call costs - resetting all costs to zero To reset all the call costs to zero you need the PIN 2 code. Alternate line service - selecting Line 2 (subscription service) Some GSM 1800 operators support the use of a second line for users. You can have two mobile phone numbers, e.g. a business and per- sonal line. To select the line for ou[...]

T h e m e nu 33 • Directly from the stand-by dis- play: Ring tone selection To choose an incoming ring tone: Volume adjustments To individually adjust the volume level of the ring tone, key tones, alarm tones and incoming audio from the stand-by display, press . Alternatively, access Volume con- trol from the Settings menu: The display confirms t[...]

34 Backlight - setting To set the backlight during key entry or incoming ring tone, you have two options: • On for 10 sec. : the display and key backlight stays on for 1 0 seconds after the last key press or incoming call. • Off : the backlight stays off except on incoming call. Display contrast To modify the display contrast be- cause of bad l[...]

T h e m e nu 35 Speed dialling You can assign phone book num- bers to keys - . Hold down the key to dial the number. The phone reserves exclusively for the voice mail number. The phone automatically assigns this key to the voice mail number if stored (see “ Voice mail ”, pag e 38). You can select any stored number. To assign phone book numbers [...]

36 KEEP A RECORD OF YOUR CODES AND KEEP THEM IN A SAFE PLACE. FAILURE TO DO SO CAN CAUSE YOU CONSIDERABLE IN- CONVENIENCE. Phone lock code A phone lock code prevents unau- thorised access to the phone and WAP™ settings. You also need it to reset the call timers. The facto- ry setting is 0000 . Reset this code and keep it in a safe place, sepa- ra[...]

T h e m e nu 37 can not turn it on or off. To change the PIN2 code: PUK code Only your service provider can give you the 8 digit PUK (PIN un- block key). Use it to 'unblock' a PIN whose code has been entered incorrectly three times. A PUK code cannot be changed. Enter the PUK code and press OK . Enter a new PIN code by following the displ[...]

38 Melody download You can also download melodies from the Trium web site (www.mitsubishi-telecom.com). This site downloads the melodies to your phone using SMS. When the download completes, Voice mail Voice mail operates like an answer- ing machine. Contact your service provider for details. Storing a voice mail centre number If your SIM does not [...]

T h e m e nu 39 Diverting incoming calls (network service) Call diverting diverts incoming calls, whether voice, fax or data, to another number. To turn on call divert: To turn off or check the status of call divert: To cancel all (multiple) diverts: Caller Line Identity - showing/hiding your mobile number Most networks allow the Caller Line Identi[...]

40 ing Receiving caller ID allows you to check its availability from the network. Receiving caller ID To find out whether a network presents the ID of incoming calls: To hide your number, on a call by call basis, add #31# before the number you are calling. Alterna- tively you can ask your service op- erator to always disable the sending of your mob[...]

T h e m e nu 41 Your SIM may contain a forbid- den list of networks which cannot be used. To view the forbidden list or show the home network: Selecting manual search To select a specific network, e.g. one which provides better cover- age in your current location: Selecting automatic search (normal default setting) To perform an automatic search fr[...]

42 Call barring (network service) To stop different types of calls be- ing made and received on the phone, you need a call barring password available only from your service provider. Call barring password Use the call barring password to select the call barring levels out- lined in the GSM Services - Call barring menu (see page 42). Your service pr[...]

T h e m e nu 43 To change the password: Broadcast - cell broadcast messag- es (Network Service) Networks can broadcast messages to all GSM users that can give infor- mation about local area dialling codes, weather reports, traffic news etc. You can decide what type of in- formation to receive by choosing the corresponding number. You can program to[...]

44 Turning the broadcast alert tone on or off To turn on or off the alert tone the phone gives when a broad- cast message arrives: Deleting or editing a message type from the list To delete or edit a message type: Broadcast language To select the broadcast language: Using the office tools The Office Tools menu contains a scratchpad, an alarm clock,[...]

T h e m e nu 45 The alarm sounds for up to 1 minute. Alarm clock and a vibrat- ing bell symbol appear with the cur- rent time and the softkeys, Valid. and No ring . During a call, the alarm also sounds. To stop the alarm: To use as a Reminder or Snooze Alarm: You can repeat the snooze for up to 15 minutes, after which the phone returns to its previ[...]

46 Games The availability and appearance of the games depend on your network opera- tor and on your mobile phone version ( Reshape and Push games are available on Trium 110 and Trium 110 m only). Reshape and Push: Game instructions appear when you select the game. Select sound effects from the menu item Options . To select a game: When in the game,[...]

T h e m e nu 47 Currency-converter To use the converter, set the curren- cies and the exchange rate: To calculate the conversion be- tween the chosen currencies: Internet/Wireless Application Protocol (WAP™) Your phone has a WAP™ internet browser to access services, such as stock buying, news, sports, weather, TV listings etc., supplied by your[...]

48 To enter and store the profile de- tails: Personalising your connection set- tings Optimise the behaviour of your phone while connected to the inter- net with the following settings: Going online To go online: Once connected, your provider spe- cific menu options appear. The icon indicates a 'live' circuit connec- tion. By default the [...]

T h e m e nu 49 a 'live' secure circuit connection. Using while online Press while online presents the following options: The appearance of these items de- pends on the operator and/or val- ues in the Settings menu. Ending the online connection To end the online connection: Creating bookmarks To revisit specific cards more quick- ly, use [...]

50 site option from the Internet menu. Addresses are not stored and must be entered each time. GSM man machine interface codes The phone supports the standard GSM key sequences using the * and # characters sent directly from the keypad to the network. These se- quences are used to activate all the supplementary services provided by the network. Con[...]

51 A cc e ss o r i e s Accessories Using the headset Connecting the headset Using the headset Disconnecting the headset Insert the headset plug in the phone headset connector as shown: While inserting the headset plug in the phone headset connector make sure the Trium logo ( ) appears on top. Otherwise the headset does not work properly. Place the [...]

52 Appendix Glossary Expression Meaning AC/DC charger Alternating Current/Di- rect Current charger Active call The call currently in con- versation ALS Alternate Line (Line 2) Service AoC Advise of Charge - sub- scription service CB Cell Broadcast CLI Caller Line Identity - dis- plays callers telephone number Conversation mode When the phone is mak[...]

53 A pp e n d i x Trouble shooting Problem Possible cause and solu- tion Phone will not switch on Check that the battery is fully charged and correctly connected to the phone. No flashing battery icon while charg- ing There may be no mains supply. Try a different elec- trical socket. The AC/DC charger may be faulty. Return to your deal- er and try [...]

54 Error messages Problem Possible cause and solution Allowed cred- it reached! You are trying to place an outgoing call and the allowed credit is already reached. The allowed credit limit is reached during an outgoing call (the call is then aborted). Busy You are trying to make a call and the call fails be- cause the destination number is already [...]

55 A pp e n d i x Problem Possible cause and solution Invalid number You tried to make a call and the call is rejected by the network be- cause the network does not recognise the phone number struc- ture or you tried to store a phone number that is too long to be stored in the selected location or you tried to move a phone entry to a loca- tion tha[...]

56 Problem Possible cause and solution Service not available Activating some GSM services that are not available on the net- work SIM blocked. Contact pro- vider A wrong PUK has been entered 10 times. The SIM card has been permanently disabled and needs to be re- placed by a new one. SIM blocked. Enter PUK: A wrong PIN code has been entered 3 times[...]

57 A pp e n d i x Guarantee Pan European Service Should you experience any difficulty then please contact your nearest MITSUBISHI location listed below for information on other service centres. To obtain Warranty Service, you will re- quire your original equipment purchase invoice or irrefutable proof of purchase. Please see warranty terms and cond[...]

58 Declaration of compliance DECLARATION OF COMPLIANCE 9 th of January 2002, Viet Mailam Managing Director Name : Mitsubishi Electric Telecom Europe S.A. RCS Nanterre B 307 593 129 Address : 25, boulevard des Bouvets Town : Nanterre Cedex Postal code : 92741 Identification of the product Nature : Mobile Cell Telephone Type : Dual band GSM 900/DCS 1[...]

59 Index I n d e x A Access to the menus ................. 20 Alarm Clock .................................. 44 Alert mode ................................ 32 Alert tone Turning on/off .................... 26 Any key answer ......................... 34 Auto Answer ............................... 35 Retry .................................. 35 Auto-d[...]

60 M Making a call ............................. 11 Managing SMS messages .......... 26 Melodies ................................... 33 Melody download ..................... 38 Menu ........................................ 20 Access ................................ 20 Menu graphics .......................... 34 Menu map ............................[...]

[...]

[...]

[...]

www.mitsubishi-telecom.com Austria 0800 292716 Germany 0800 1808133 Netherlands 0800 0223825 Belgium 0800 75733 Greece 00800 44131247 Portugal 0800 880264 Denmark 8088 1816 Ireland 1800 927012 Spain 9009 34497 Finland 0800 116975 Italy 800 791029 Sweden 0200 214715 France 0800 913080 Luxembourg 800 23 552 UK 0800 9120020 FA9M078910-A[...]