Français dropdown-ico

Moxa Technologies NPort 5110 Series manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Moxa Technologies NPort 5110 Series. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Moxa Technologies NPort 5110 Series ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Moxa Technologies NPort 5110 Series décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Moxa Technologies NPort 5110 Series devrait contenir:
- informations sur les caractéristiques techniques du dispositif Moxa Technologies NPort 5110 Series
- nom du fabricant et année de fabrication Moxa Technologies NPort 5110 Series
- instructions d'utilisation, de réglage et d’entretien de l'équipement Moxa Technologies NPort 5110 Series
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Moxa Technologies NPort 5110 Series ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Moxa Technologies NPort 5110 Series et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Moxa Technologies en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Moxa Technologies NPort 5110 Series, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Moxa Technologies NPort 5110 Series, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Moxa Technologies NPort 5110 Series. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    NPort 51 10 Series User ’ s Manual First Edition, December 2004 www .moxa.com/product Moxa Technologies Co., Ltd. Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Web: www.moxa.com MOXA Technical Support Worldwi de: support@moxa.com.tw The Americas support@moxa.com[...]

  • Page 2

    NPort 5110 User’s Manual The software d escribed in thi s manual i s furnished u nder a license agreem ent and m ay be used onl y in accordance with the term s of that agreement. Copyright Notice Copyright  2004 Moxa Technologies Co., Ltd. All rights reserved. Reproducti on without perm ission is prohi bited. Trademarks MOXA is a re gistered t[...]

  • Page 3

    Table of Contents Chapter 1 Introduction .............................................................................................. 1-1 Overview .......................................................................................................... 1-2 Package Checkl ist .......................................................................[...]

  • Page 4

    Chapter 6 Configuring Windows Administrator ...................................................... 6-1 Overview .......................................................................................................... 6-2 Installing Windows Ad ministrator..................................................................... 6-2 Configuration ......[...]

  • Page 5

    1 1 Chapter 1 Introduction Welcome to NPort 5110, an a dvanced, 1-p ort RS-232 seri al device server t hat makes it easy to network-ena ble your de vices. The following topics are covered in t his chapter: ! Overview ! Package Checklist ! Product Features ! Product Specifications[...]

  • Page 6

    NPort 5110 Series User’s Manual Introduction 1-2 Overview NPort 5110 se rial device ser ver is designe d to make your i ndustrial seri al devices Int ernet ready instantly, and is well-suited for POS security market applicatio ns. The compact size of NPort 5110 device server makes them the ideal choice for connecting your RS-232 serial devices, s[...]

  • Page 7

    NPort 5110 Series User’s Manual Introduction 1-3 Product Specifications LAN Ethernet 10/10 0 Mbps, RJ 45 Protection Built-in 1.5 KV magnetic isolation NPort 5110 Serial Interface Interface RS-232 No. of Ports 1 Port Type Male DB9 Signals TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND Serial Line Pro tection 15 KV ESD fo r all signals Power Line Protectio[...]

  • Page 8

    2 2 Chapter 2 Getting Started This chapter include s information about installin g NPort 5110. The following top ics are covered: ! Panel Layout ! Connecting the Hardware " Connecting the Power " Connecting to the Network " Connecting to a Serial Device " LED Indicators[...]

  • Page 9

    NPort 5110 Series User’s Manual Getting Started 2-2 Panel Layout NPort 5110 T op Panel View DIN-Rail screw hole W allmount screw hole Ready Link Tx/Rx Serial Device Server 51 10 10/100M Ethernet RESET 9-30VDC Port 1 RS-232 Male DB9 serial port Front Panel View RJ45 10/100M Ethernet port Reset button Power input Rear Panel View Stick-on pad Connec[...]

  • Page 10

    NPort 5110 Series User’s Manual Getting Started 2-3 Connecting to the Network Connect one e nd of the Eth ernet cable to NPort 5110’ s 10/100M Ethernet port and the other end of the cable to the Ethernet netwo rk. NPort 5110 will indicate a valid con nection to the Ethernet in the following ways: ! The Ethernet LED maintains a solid green color[...]

  • Page 11

    3 3 Chapter 3 Initial IP Address Configuration When setting up your NPor t 5110 for the first time, you sh ould first conf igure the IP address. Th is chapter introduces the method to co nfigure the devi ce server’s IP address. For m ore details about network settings, see the Network Settings section from Chapter 5, Web Cons ole Configuration. T[...]

  • Page 12

    NPort 5110 Series User’s Manual Initial IP Address Configuration 3-2 Initializing NPort 5110’s IP Address 1. Determine whether your NPort 5110 needs to use a Static IP or Dynamic IP (either DHCP or BOOTP application). 2. If NPort 5110 is used in a Static IP environment, you ca n use NPort 5110 Adm inistration Suite, ARP, Web Console, Telnet Con[...]

  • Page 13

    NPort 5110 Series User’s Manual Initial IP Address Configuration 3-3 Take the following steps to use ARP to con figure the IP address: 1. Obtain a valid IP address for your NPort 5110 from your network ad ministrator. 2. Obtain NPort 5110’s MAC address fro m the label on its bottom panel. 3. Execute the ‘arp -s’ comm and from your com puter[...]

  • Page 14

    NPort 5110 Series User’s Manual Initial IP Address Configuration 3-4 4. Type 2 to select Netw ork settings , and then press Enter . 5. Type 1 to select IP address and then press Enter .[...]

  • Page 15

    NPort 5110 Series User’s Manual Initial IP Address Configuration 3-5 6. Use the Backspace key to erase the current IP address, type in the new IP address, and then press Enter . 7. Press any key to contin ue.[...]

  • Page 16

    NPort 5110 Series User’s Manual Initial IP Address Configuration 3-6 8. Type m and th en press Enter to return to the m ain menu. 9. Type s and then pr ess Enter to Save /Restart the system. 10. Type y and then press Enter to save the new IP addre ss and restart NP ort 5110. Serial Console (19200, n, 8, 1) You may use t he RS-232 c onsole port to[...]

  • Page 17

    NPort 5110 Series User’s Manual Initial IP Address Configuration 3-7 1. Connect NPort 5110’s serial port 1 directly to your computer’s male RS-232 serial port. 2. From the Windows desktop click on Start $ Programs $ PComm Lite $ Terminal Emulator . 3. When the PC omm Terminal Emulator window opens, first click on the Port Manage r menu item a[...]

  • Page 18

    NPort 5110 Series User’s Manual Initial IP Address Configuration 3-8 8. Input the password when prompted. Note that this page will only appe ar when the NPort 5110 has been set up for password prot ection. 9. Start configuring th e IP address under Network Settings . Refer to step 4 in the Telnet Console section for instructions on how to co nfig[...]

  • Page 19

    4 4 Chapter 4 Choosing the Proper Operation Mode In this section, we describe t he various NP ort 5110 operation m odes. The opt ions inclu de an operation m ode that uses a driver instal led on the h ost compute r, and oper ation modes t hat rely o n TCP/IP socket programmi ng concepts. A fter choosi ng the proper operation mode in this chap ter, [...]

  • Page 20

    NPort 5110 Series User’s Manual Choosing the Proper Operation Mode 4-2 Overview NPort 5110 S erial Devi ce Servers are used to netw ork-enable t raditional RS-232 device s. A Serial Device Server is a tiny computer equi pped wit h a CPU, real-tim e OS, and TC P/IP protoc ols that can bi-directionally transfer data between the se rial and Ethernet[...]

  • Page 21

    NPort 5110 Series User’s Manual Choosing the Proper Operation Mode 4-3 UDP Mode Compared to TCP comm unication, UDP is faster and m ore efficient. I n UDP mode, y ou can unicast or multicast data from the serial device to one or multiple host computers, and the serial device can also receive data from one or multip le host com puters, maki ng thi[...]

  • Page 22

    NPort 5110 Series User’s Manual Choosing the Proper Operation Mode 4-4 Ethernet Modem Mode The Ethernet Mod em operation mode is designed fo r use with l egacy operating systems, such as MS-DOS, that do not support TCP/ IP Ethernet. By connecting one NP ort 5110’s serial port t o the MS-DOS computer’s serial port, it is possible to use legacy[...]

  • Page 23

    5 5 Chapter 5 Web Console Configuration The Web Cons ole is the m ost user-frien dly met hod available t o configure NPort 511 0. This chapter introd uces the Web Consol e function gro ups and functio n definitions . ! Opening Your Browser ! Basic Settings ! Network Settings ! Serial Settings ! Operating Settings " Real COM Mode " TCP Ser[...]

  • Page 24

    NPort 5110 Series User’s Manual Web Console Configuration 5-2 Opening Your Browser 1. Open your browser with the cookie function en abled . (To enable your browser fo r cookies, right click on your des ktop Internet Explorer i con, select Properties, click on the Security tab, and then select the three Enable options as shown in the figure below.[...]

  • Page 25

    NPort 5110 Series User’s Manual Web Console Configuration 5-3 ATTENTION Refer to Chapter 3, “Initial IP Address Configur ation,” to see how to configure the IP address. Examples shown in this chapter use th e Factory Default IP address (192.168.127 .254). 4. The NPort 5110 hom epage will ope n. On thi s page, you ca n see a brief descriptio n[...]

  • Page 26

    NPort 5110 Series User’s Manual Web Console Configuration 5-4 Basic Settings Server name Setting Factory Defaul t Necessity 1 to 39 characters [model name]_[Serial No.] Optional This option is useful for specifying the locati on or app lication of different N Port 5110s. Web/Telnet Console The “Disable” option f or “W e b Console” an d ?[...]

  • Page 27

    NPort 5110 Series User’s Manual Web Console Configuration 5-5 Network Settings Y ou must assign a valid IP address to NPort 51 10 before it will work in your network environment. Y our network syste m administrator should pro vide you with an IP address and related settings for your network. The IP address must be un ique within the network (othe[...]

  • Page 28

    NPort 5110 Series User’s Manual Web Console Configuration 5-6 IP address Setting Factory Defaul t Necessity E.g., 192.168.1.1 (IP addresses of the form x . x . x .0 an d x . x . x .255 are inva lid.) 192.168.1 27.254 R equired An IP address is a number assi gned to a netw ork device (s uch as a c omputer) as a permanent address on the network. Co[...]

  • Page 29

    NPort 5110 Series User’s Manual Web Console Configuration 5-7 connect to the web server. DNS is t he way that In ternet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates t his kind of te xt-based dom a[...]

  • Page 30

    NPort 5110 Series User’s Manual Web Console Configuration 5-8 Auto report to IP Setting Factory Defaul t Necessity E.g., 192.168.1.1 or URL (IP addresses of the form x . x . x .0 an d x . x . x .255 are inva lid.) None Optional Reports generated by the Auto report fu nction will be automatically sent to this IP address. Auto report to TCP port Se[...]

  • Page 31

    NPort 5110 Series User’s Manual Web Console Configuration 5-9 Port alias Setting Factory Defaul t Necessity 1 to 15 characters (E.g. , PLC-No.1 ) None Optional “Port alias” is included to allo w easy identification of the serial devices that are c onnected to NPort 5110’s s erial port. Serial Parameters ATTENTION Check the serial communicat[...]

  • Page 32

    NPort 5110 Series User’s Manual Web Console Configuration 5-10 Operating Settings Click on Operating Se ttings , located under Main Menu, to display the operating settings for both of NPort 5110’s serial ports. Real COM Mode TCP alive check time Setting Factory Defaul t Necessity 0 to 99 m in 7 min Optional 0 min: TCP connection is not closed d[...]

  • Page 33

    NPort 5110 Series User’s Manual Web Console Configuration 5-11 Max connection 2 to 4: Allows 2 to 4 host’s Real COM drivers to open the specific NPort 5110 serial port, at the same time. When multiple hosts’ Real COM drivers open the serial p ort at the same time, the COM driver only provides a pure data tunnel without control ab ility. That [...]

  • Page 34

    NPort 5110 Series User’s Manual Web Console Configuration 5-12 buffer is full or if the Force transmit time interv al reaches the time specified unde r Force transmit timeout. The optimal Force transmit timeo ut depends on your app lication, but it must be at least larg er than one character interval within the specified ba ud rate. For exam ple,[...]

  • Page 35

    NPort 5110 Series User’s Manual Web Console Configuration 5-13 for the given time. After the connection is closed, NPor t 5110 starts listening for another host’s TCP connection. This paramet er defines the m aintenance statu s as Closed or Listen for the TCP connection. The connection is c losed if there i s no incom ing or out going data thro[...]

  • Page 36

    NPort 5110 Series User’s Manual Web Console Configuration 5-14 Force transmit Setting Factory Defaul t Necessity 0 to 65535 ms 0 ms Optional 0: Disable the force transm it timeout. 1 to 65535: Forces the NPor t 5110’s TCP/IP prot ocol software to try to pa ck serial data received during the specified time into the same data frame. This paramete[...]

  • Page 37

    NPort 5110 Series User’s Manual Web Console Configuration 5-15 TCP Client Mode TCP alive check time Setting Factory Defaul t Necessity 0 to 99 m in 7 min Optional 0 min: TCP connection is not closed due to an id le TCP connection. 1 to 99 min: NPort 5110 automatically closes the TCP connection if there is no TCP activity for the given time. Inact[...]

  • Page 38

    NPort 5110 Series User’s Manual Web Console Configuration 5-16 ATTENTION The Inactivity time should at least be set larger than that of Fo rce transmit t imeout. To pr event the unintended loss of data due to th e session being disconnected, it is highly recommended th at this value is set large enough so that the intended d ata transfer is compl[...]

  • Page 39

    NPort 5110 Series User’s Manual Web Console Configuration 5-17 ( 10 (bits) / 1200 (bit s/s) ) * 1000 (m s/s) = 8.3 ms. Therefore, you should set Force transmit timeou t to be larger than 8.3 ms, so in this case, it must be greater than or equal to 10 ms. If the user wants to send a se ries of characters in the sam e packet , the serial device att[...]

  • Page 40

    NPort 5110 Series User’s Manual Web Console Configuration 5-18 UDP Mode Delimiter 1 Setting Factory Defaul t Necessity 00 to FF None Optional Delimiter 2 Setting Factory Defaul t Necessity 00 to FF None Optional Once the NPort 5110 recei ves both delimiters through its serial port, it immediately packs all data currently in it s buffer a nd sends[...]

  • Page 41

    NPort 5110 Series User’s Manual Web Console Configuration 5-19 internal buffer. NPort 5110 transmits data stored in the buffer via TCP/IP, but only if the internal buffer is full or if the Force transmit time interv al reaches the time specified unde r Force transmit timeout. The optimal Force transmit timeo ut depends on your app lication, but i[...]

  • Page 42

    NPort 5110 Series User’s Manual Web Console Configuration 5-20 Pair Connection Slave Mode TCP alive check time Setting Factory Defaul t Necessity 0 to 99 m in 7 min Optional 0 min: TCP connection is not closed due to an id le TCP connection. 1 to 99 min: NPort 5110 automatically closes the TCP connection if there is no TCP activity for the given [...]

  • Page 43

    NPort 5110 Series User’s Manual Web Console Configuration 5-21 Pair Connection Master Mode TCP alive check time Setting Factory Defaul t Necessity 0 to 99 m in 7 min Optional 0 min: TCP connection is not closed due to an id le TCP connection. 1 to 99 min: NPort 5110 automatically closes the TCP connection if there is no TCP activity for the given[...]

  • Page 44

    NPort 5110 Series User’s Manual Web Console Configuration 5-22 Ethernet Modem Dial-in NPort 5110 l istens for a TCP/IP connecti on request f rom the rem ote Ethernet m odem or host . NPort 5110’s respons e depends on the ATS0 value, as outlined below. ATS0=0 (default): NPort 5110 will temporarily accept the TCP connection and then send the “R[...]

  • Page 45

    NPort 5110 Series User’s Manual Web Console Configuration 5-23 Disconnection request from remote site After the TCP connection has bee n shut do wn by the rem ote Ethernet m odem or PC, NPort 5110 will send the “NO CARRIER” signal via the se rial port and then return to command mode. Ethernet Modem Setting V alue Notes Necessity TCP port vali[...]

  • Page 46

    NPort 5110 Series User’s Manual Web Console Configuration 5-24 16 A T&D Serial port DTR control A T&D0=recognize DTE always ready A T&D1, A T&D2=reply DTE when DTR On (default) 17 A T&F Restore manufacturer’ s settings 18 A T&G Select guard ti me repl y “OK” on ly 19 A T&R Serial port R TS option co mmand reply ?[...]

  • Page 47

    NPort 5110 Series User’s Manual Web Console Configuration 5-25 TCP port Setting Factory Defaul t Necessity 1 to 65535 4001 Required The TCP port t hat other devi ces must use to contact t his device. T o avoid confl icts with s tandard TCP ports, the default is set to 4001. TCP alive check time Setting Factory Defaul t Necessity 0 to 99 m in 7 mi[...]

  • Page 48

    NPort 5110 Series User’s Manual Web Console Configuration 5-26 ! Any host c an access the NP ort 5110 Disable this function by un-checking the “Enabl e the accessible IP list” checkbox. Refer to the following table for more configuration ex amples. Allowable Hosts Input format Any host Disable 192.168.1.120 192.16 8.1.120 / 255.255.255.255 19[...]

  • Page 49

    NPort 5110 Series User’s Manual Web Console Configuration 5-27 From E-mail ad dress Setting Factory Defaul t Necessity 1 to 63 characters None Optional E-mail address 1/ 2/3/4 Setting Factory Defaul t Necessity 1 to 63 characters None Optional ATTENTION Consult your Netw ork Admini strator or ISP for t he proper mail server sett ings. The Auto wa[...]

  • Page 50

    NPort 5110 Series User’s Manual Web Console Configuration 5-28 IP address changed The user has ch anged NPort 5110’s IP address. When the IP address ch anges, NPort 5110 will send an e-mail with the new IP address before NP ort 5110 reboots. If the NPort 5110 is unable to send an e-mail message to the mail server within 15 seconds, NPort 5110 w[...]

  • Page 51

    NPort 5110 Series User’s Manual Web Console Configuration 5-29 Change Password Input the “O ld password ” and “New p assword” to change the password. Leave the password boxes blank to erase t he passwor d. If the passwo rd is erased, then NPort 5110 wil l not have password protection. ATTENTION If you forget the password, the ONLY way to [...]

  • Page 52

    6 6 Chapter 6 Configuring Windows Administrator The following topics are covered in t his chapter: ! Overview ! Installing Windows Administrator ! Configuration " Broadcast Search " Unlock Password Protection " Configuring NPort 5110 " Upgrade Firmware " Export/Import ! Monitor ! Port Monitor ! COM Mapping " On-line CO[...]

  • Page 53

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-2 Overview Windows Administr ator is designed to let you install an d configure your NPort 5110 pr oducts easily over the network. Windows Adm inistrator provides fi ve function groups that ease the installation p rocess, allows off-line COM mapping, a nd provi des monitor ing an[...]

  • Page 54

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-3 3. Click on Next to install program files in the default directory, or select an alternative lo cation. 4. Click on Next to install the program using the default program name, or select a different name.[...]

  • Page 55

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-4 5. Click on Install to proceed with the installation. 6. The Installing window reports the p rogress of the installation.[...]

  • Page 56

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-5 7. Click on Next to proceed with the installation. 8. Click on Finish to complete the installation of NPort 5110 Administration Suite.[...]

  • Page 57

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-6 Configuration The Admi nistrator-Confi gurati on window is divided int o four pa rts. ! The top part is the function list and onlin e help area. (Windows NT does not suppo rt this .chm file format.) ! The left pa rt lists the fi ve Admi nistrator fun ction groups . ! The right [...]

  • Page 58

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-7 Broadcast Search 1. The Broadcast Search function is used to loca te all NPort 5110s that are connected to the same LAN as your computer. Since the Broadcast Search function searches by MAC address and not IP address, all NPort 5110s connected to the LAN will be located, regard[...]

  • Page 59

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-8 2. The Broadcast Search window will op en and disp lay th e Model, IP Address, MAC Address, and Progress (of the sear ch fo r that particular device).[...]

  • Page 60

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-9 3. When the search is complete, the Broadcast S earch window closes, and the NPort 5110s that were located are displayed in the right pane of the Ad ministrator window. If you foun d more tha n one serve r connected to this netwo rk, refer t o the MAC ad dress sticker on your s[...]

  • Page 61

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-10 Unlock Password Protection 1. If the NPort 5110 is password protected, then you will not be able to use th e right click method to open the configura tion page . 2. Instead, select an NPort 5110 with “Lock” status, right click the lo cked NPort 5110, and then select the un[...]

  • Page 62

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-11 4. The previous “Lock” status will switch to “Unlock” status. Administrator will keep this NPort 5110 in the Unlock status throughou t this Administrator session. The meanings of the six state s are as follows ( note t hat the term Fixed is borr owed from the standard [...]

  • Page 63

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-12 Configuring NPort 5110 1. Input the password to Unlock the NPort 5110. Righ t click on a specific NPort 5110 and select configure to start the conf iguration. 2. The progress bar shows that Administrator is retrieving configuration information from the specific NPort 5110.[...]

  • Page 64

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-13 3. Refer to Chapter 5 for each parameter’s function definition. To modify the configuration, you must first click in the modify box to activate the parameter setting box. ATTENTION You can simultaneously modify th e configurations of multiple NPort 5110s th at are of the sam[...]

  • Page 65

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-14 Upgrade Firmware 1. Input the password to Unlock the NPort 511 0, and then right click on a specific NPor t 5110 and select the Upgrade Firmware function to start upgrading the firmware. 2. Select the correct ROM file to be downloaded to the NPort 5110. 3. Wait patiently while[...]

  • Page 66

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-15 Export/Import Right click on a specific NPort 5110 and select the Export function to start Exp orting the configuration file. The Exp ort Configu ration functi on is a handy tool that can be use d to produce a text file cont aining the curre nt config uration of a part icular [...]

  • Page 67

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-16 ATTENTION You can simultaneously import the same configuration file into multiple NPor t 5110s that are of the same model. To select multiple NPort 5110s, hold down the Ctrl key when selecting an additio nal NPort 5110, or hold do wn the Shift key to select a block of NPort 51[...]

  • Page 68

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-17 4. Select Add Target . 5. When you select Add Target, you will see a NPort 5110 list that looks the same as when using Configuration $ Broadcast Search. Chec k the NPort 5110 you would like to Monito r, and then click OK . 6. The NPort 5110 list will now appear on th e Monitor[...]

  • Page 69

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-18 8. Select or de-select Monitor Items . Use the singl e arrowhe ad buttons to move hig hlighted items from one box to the other. Use the double arrowhead buttons to move all items in one box to the other. 9. Select a Refre sh Rate (the default is 3 seconds).[...]

  • Page 70

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-19 10. Select Display warning message for new event or Play warning music for new event. In the second case, you must enter the path t o the WAV fi le that you want to be played. “New event” means that one of the NP ort 5110s in the monitor is “Alive” or “Not Alive,” [...]

  • Page 71

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-20 12. For this example, the NPort 5110 shown in the list will be monitored. 13. When one of the NPort 5110s loses connection with the Monitor program, a warning alert will display automatically. The warning music will be played at the same time. 14. In the Monitor screen, you ca[...]

  • Page 72

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-21 15. If the NPort 5110 gets reconnected, a warning w ill be displayed to remind the user that the NPort 5110 is n ow “Alive.” 16. The NPort 5110 that was reconnected, and is now “Aliv e,” will be shown in black color.[...]

  • Page 73

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-22 Port Monitor The process descri bed here is the same as in the previous “M onitor” section . The only di fference is that you can select more items un der Port Monitor than under Monitor. Select or de-select Moni tor Items . Use the single a rrowhead buttons to move highl [...]

  • Page 74

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-23 COM Mapping Windows Administr ation Suite comes with Windows 95 /98/ME/NT/2000/XP Real COM d rivers. After you install NPort 5110 Administration Suite, there are two ways to set up the NPort 5110’s serial port as your host’ s remote COM port. The first way is with On-line [...]

  • Page 75

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-24 3. Add the target to which you would like to map COM ports. 4. The NPort 5110 list that appears is the list gene rated by the previous Br oadcast Search. S elect the NPort 5110 that you would lik e to map COM ports to. 5. Select COM Settin gs to mod ify COM No. , default setti[...]

  • Page 76

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-25 6. Select the COM No. COM ports that are “In use” or “Assigned” will also be indicated in this drop-down list. If you select multiple serial ports or multiple NPor t 5110s, remember to check the “Auto Enum erating” func tion to use the COM No. you select as the fir[...]

  • Page 77

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-26 Enable/Disable Tx/Rx FIFO . If disabled, NPort 5110 will se nd one byte each time the Tx FIFO becomes empty; and an Rx interrupt will be generated for each incoming byte. This will result in a faster response and low er throughput. If you want to use XON/XO FF flow control, we[...]

  • Page 78

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-27 7. The Serial Pa rameter set tings shown here are the default set tings when t he NPort 5110 is powered on. However, t he program can redefine th e serial parameters to different value s after the program opens the port via Win 3 2 API. 8. After setting the COM Mapping, rememb[...]

  • Page 79

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-28 9. Select Discard Change t o tell Administrator NOT to save the C OM Mappi ng inform ation to the host. 10. To save the configuration to a text file, select Export CO M Mapping . You will then be able to import this configur ation file to another host and use the same COM Mapp[...]

  • Page 80

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-29 Off-line COM Mapping 1. Add a target by inputting the IP address and selecting the Model Name without physically connecting the NPort 5110 to the network. 2. Select Apply ch ange .[...]

  • Page 81

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-30 IP Location When NPort 5110 is used i n a dynam ic IP enviro nment, users m ust spend m ore time wi th IP management tasks. NPort 5110 produ cts help out by periodically reporting th eir IP address to the IP location server, in case the dynamic IP has changed. ! Receive NPort [...]

  • Page 82

    NPort 5110 Series User’s Manual Configuring Windows Administrator 6-31 3. Next, configure the Local Listen Port to be the sam e as the NPort 5110’s “Auto report to UDP port” setting. 4. Click Go to start receiving the Auto IP ad dress report from the NPort 5110.[...]

  • Page 83

    7 7 Chapter 7 IP Serial LIB The following topics are covered in t his chapter: ! Overview ! IP Serial LIB Function Groups ! Example Program[...]

  • Page 84

    NPort 5110 Series User’s Manual IP Serial LIB 7-2 Overview What is IP Seri al Library? IP Serial Library is a Windows libr ary with freq uently used serial comm and sets and s ubroutine s. IP Serial Library is designed to reduce t he comple xity and poor efficiency of serial c ommunication over TCP/IP. For example, Te lnet can only transfer data,[...]

  • Page 85

    NPort 5110 Series User’s Manual IP Serial LIB 7-3 IP Serial LIB Function Groups Server Control Port Co ntrol I nput/Ou tput Data Port Statu s Inquiry Miscellaneous nsio_init nsio_end nsio_resetserv er nsio_checkalive nsio_open nsio_close nsio_ioctl nsio_flowct rl nsio_DTR nsio_RTS nsio_lctrl nsio_baud nsio_resetport nsio_read nsio_SetReadTim eout[...]

  • Page 86

    A A Appendix A Pinouts and Cable Wiring In this appendix, we cover the fo llowing topics. ! Port Pinout Diagrams " Ethernet Port Pinouts " Serial Port Pinouts ! Cable Wiring Diagrams " Ethernet Cables[...]

  • Page 87

    NPort 5110 Series User’s Manual Pinouts and Cable Wiring A-2 Port Pinout Diagrams Ethernet Port Pinouts Serial Port Pinouts DB9 Male RS-232 port pinouts fo r NPort 5110 PIN SIGNAL 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 ---[...]

  • Page 88

    NPort 5110 Series User’s Manual Pinouts and Cable Wiring A-3 Cable Wiring Diagrams Ethernet Cables[...]

  • Page 89

    B B Appendix B Well Known Port Numbers In this appendix, which is in cluded for your re ference, we p rovide a list of Well Known port numbers that may cause network prob lems if you set NPort 5110 to one of these ports. Refer to RFC 1700 for Well Know n port num bers, or refer to the following i ntroduction from the IANA. The port numbers are divi[...]

  • Page 90

    NPort 5110 Series User’s Manual Well Known Port Numbers B-2 TCP Socket Application Service 42 Host name server (names server) 43 Whois (nickname) 49 (Login Host Protocol ) (Login) 53 Domain Name Server (dom ain) 79 Finger protocol (Finger) 80 W orld W ide W eb HTTP 1 19 Network ne ws T ransfer Proto col (NNTP ) 123 Network T im e Protocol 213 IPX[...]

  • Page 91

    NPort 5110 Series User’s Manual Well Known Port Numbers B-3 UDP Socket Application Service 161 SNMP (Simple Netwo rk Mail Prot ocol) 162 SNMP T raps 213 IPX (Used for IP T unneling)[...]

  • Page 92

    C C Appendix C SNMP Agents with MIB II & RS-232 Like Groups NPort 5110 has built-in SNMP (Simple Network Management Protocol) agent so ftware that supports SNMP Trap, RFC1317 RS-23 2 like groups and RFC 12 13 MIB-II. The following table lists the standard MIB-II groups, as well as the variable implementation for NPort 5110. RFC1213 MI B-II supp[...]

  • Page 93

    NPort 5110 Series User’s Manual SNMP Agents C-2 System MIB Interfaces MIB IP MIB ICMP MIB SysServices ifInUnknownProtos ipReasmFails IcmpOutT imeExcds ifOutOctets ipFragOKs IcmpOutParmProbs ifOutUcastPkts ipFragFails Icm pOutSrcQuenchs ifOutNUcastPkts ipFrag Creates IcmpOutRedirects ifOutDiscards ipAdEntAddr IcmpOutEchos ifOutErrors ipAdEntIfI nd[...]

  • Page 94

    NPort 5110 Series User’s Manual SNMP Agents C-3 Address T ranslation MIB TCP MIB SNMP MIB AtNetAddress tcpRetransSegs snmpInT otalSetV ars tcpConnState snmpInGetRequests tcpConnLocal Address snmpInGetNe xts tcpConnLocal Port snmpInSetRe quests tcpConnRem Address snmpInGetRespo nses tcpConnRem Port snmpInT raps tcpInErrs snmpOutT ooBigs tcpOutRst [...]

  • Page 95

    NPort 5110 Series User’s Manual SNMP Agents C-4 The Input Signal T able The Output Signal T able rs232InSigT able rs232 OutSigT able rs232InSigEn try rs232OutSigEntry rs232InSigPor tIndex rs232Ou tSigPortIndex rs232InSigName r s232OutSigName rs232InSigState rs232OutSigState[...]

  • Page 96

    D D Appendix D Auto IP Report Protocol NPort Series provides several ways to confi gure Ethernet IP addresses. One method i s DHCP Client. When y ou set up the N Port to use D HCP Client to c onfigure Et hernet IP addresse s, a DHCP request is sent automatically ov er the Ethernet to find the DH CP Server. In response, the DHCP Server will send an [...]

  • Page 97

    NPort 5110 Series User’s Manual Auto IP Report Protocol D-2 You will then be able to develop your own progra ms to receive this informatio n from the NPort. Here is NPo rt’s Auto IP Report Pr otocol. Cl ick on the following link to link to a specific example. http://web2.moxa.com.tw/services/download /download.asp Auto IP Report Format “MOXA?[...]

  • Page 98

    E E Appendix E Service Information This appen dix shows yo u how to cont act Moxa f or inform ation about t his and ot her product s, and how to repor t problems. In this appendix, we cover the fo llowing topics. ! MOXA Internet Services ! Problem Report Form ! Product Return Procedure[...]

  • Page 99

    NPort 5110 Series User’s Manual Service Information E-2 MOXA Internet Services Customer satisfaction is our num b er one concern, and to ensure that customers receive the full benefit of ou r products, M oxa Internet Services has bee n set up to p rovide technical s upport, dri ver updates, product infor mation, and user’s manual updates. The f[...]

  • Page 100

    NPort 5110 Series User’s Manual Service Information E-3 Problem Report Form MOXA NPort 51 10 Customer name: Comp any: T el: Fax: Email: Date: Moxa Product: NPort 5110 Serial Number: ___________ ____ __ Problem Description: Please descri be the sym ptoms of the pr oblem as clearly as possible, incl uding any error messages you see. A clearly writt[...]

  • Page 101

    NPort 5110 Series User’s Manual Service Information E-4 Product Return Procedure For product repair, exc hange, or re fund, the customer m ust: % Provide evidence of original purchase. % Obtain a Product Return Agreement (PRA) from the sales representative or dealer. % Fill out the Problem Report Form (PRF). Include as much detail as possible for[...]