Nissan Altima (2013) manuel d'utilisation

® 2013 AL TI MA S E D AN OWN E R’S MAN UAL For y our s afety , read car efully and keep in this v ehicle. 2013 N IS SAN AL TI MA SE DAN L33-D L33-D Printing : December 2012 (05) Publication No.: OM0E 0L32U2 Printed in U .S.A. OM3E 0L33U4[...]

W elcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you under- stand the operation and maintenance of your vehicle so that you may enjoy many miles (kilome- ters) of driving pleasure. Please rea[...]

MODIFICA TION OF Y OUR VEHICLE This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or per- formance problems resulting from modi- fications may not be covered under NISSAN warranties. This manual includes information for all options [...]

CALIFORNIA PROPOSITION 65 W ARNING WARNING Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth de- fects or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear contain or emit chem[...]

NISSAN CARE S... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Y our satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Y our NISSAN dealer is always available to assist you with all your automobile sales and service needs. However, if there is something that your NISSAN dealer c[...]

T able of Contents Illustrated table of contents Safety—Seats, seat belts and supplemental restraint system Instruments and controls Pre-driving checks and adjustments Monitor, climate, audio, phone and voice recognition systems Starting and driving In case of emergency Appearance and care Maintenance and do-it-yourself T echnical and consumer in[...]

[...]

0 Illustrated table of contents Air bags, seat belts and child restraints ..............0 - 2 Exterior front ......................................0 - 3 Exterior rear .......................................0 - 4 Passenger compartment ...........................0 - 5 Instrument panel ...................................0 - 6 Engine compartment check [...]

1. T op tether strap anchor (P . 1-23) 2. Rear seat belts (P . 1-10) 3. Roof-mounted curtain side-impact supplemental air bag (P . 1-37) 4. Front seat-mounted side-impact supplemental air bag (P . 1-37) 5. Head restraints (P . 1-7) 6. Front seat belts (P . 1-10) 7. Side-impact pressure sensor (driver’s side shown; passenger’s side similar) (P .[...]

1. P ower windows (P . 2-42) 2. Windshield (P . 8-21) 3. Windshield wiper and washer switch (P . 2-28) 4. Engine hood (P . 3-27) 5. Tie down (P . 6-13) 6. Fog light switch (if so equipped) (P . 2-29) 7. Headlight and turn signal switch (P . 2-30) 8. Replacing bulbs (P . 8-28) 9. Tire pressure (P . 8-35) 10. Flat tire (P . 6-3) 11. Tire chains (P . [...]

1. Rear window defroster switch (P . 2-29) 2. Interior trunk lid release (P . 3-29) 3. T runk lid (P . 3-27) 4. Opener operation (P . 3-27) 5. Replacing bulbs (P . 8-28) 6. Fuel-filler cap, fuel recommendation (P . 3-30, P . 9-3) 7. Fuel-filler door (P . 3-30) 8. Child safety rear door lock (P . 3-6) See the page number indicated in paren- theses f[...]

1. Interior trunk access (P . 1-6) 2. Moonroof (if so equipped) (P . 2-45) 3. Sun visors (P . 3-32) 4. Interior lights, illuminated entry (P . 2-46) 5. HomeLink® universal transceiver (if so equipped) (P . 2-48) 6. Automatic anti-glare rearview mirror (if so equipped) (P . 3-33) 7. Glove box (P . 2-41) 8. Cup holders (P . 2-40 ) 9. Console box (P [...]

1. Instrument brightness control/T rip com- puter reset switch (P . 2-33, P . 2-4) 2. V ents (P . 4-20) 3. Headlight/fog light (if so equipped)/turn signal switch (P . 2-30) 4. Driver supplemental air bag/horn (P . 1-37, P . 2-34) 5. Meters and gauges (P . 2-3) 6. Paddle shift controls (if so equipped) (P . 5-15) 7. Windshield wiper/washer switch ([...]

22. V ehicle Dynamic Control OFF switch (P . 2-37) T runk opener (P . 3-27) Heated steering wheel switch (if so equipped) (P . 2-36) W arning system switch (if so equipped) (P . 2-36) * Refer to the Navigation System Owner’s manual (if so equipped) See the page number indicated in paren- theses for operating details. Illustrated table of contents[...]

QR25DE engine 1. P ower steering fluid reservoir (P . 8-14) 2. Engine coolant reservoir (P . 8-8) 3. Engine oil filler cap (P . 8-10) 4. Brake fluid reservoir (P . 8-15) 5. Air cleaner (P . 8-20) 6. Fuse/fusible link box (P . 8-23) 7. Battery (P . 8-16) 8. Engine oil dipstick (P . 8-10) 9. Radiator cap (P . 8-8) 10. Drive belt location (P . 8-19) 1[...]

VQ35DE engine 1. P ower steering fluid reservoir (P . 8-14) 2. Engine coolant reservoir (P . 8-8) 3. Engine oil filler cap (P . 8-10) 4. Brake fluid reservoir (P . 8-15) 5. Air cleaner (P . 8-20) 6. Fuse/fusible link box (P . 8-23) 7. Battery (P . 8-16) 8. Engine oil dipstick (P . 8-10) 9. Radiator cap (P . 8-8) 10. Drive belt location (P . 8-19) 1[...]

W arning light Name Page Anti-lock Braking System (ABS) warn- ing light 2-10 or Brake warning light 2-11 Charge warning light 2-11 Low tire pressure warning light 2-11 Master warning light 2-13 P ower steering warning light 2-13 Seat belt warning light and chime 2-13 W arning light Name Page Supplemental air bag warning light 2-14 Indicator light N[...]

1 Safety—Seats, seat belts and supplemental restraint system Seats . ...........................................1 - 2 Front manual seat adjustment — (for passenger’s seat) ...........................1 - 2 Front power seat adjustment (for driver’s seat) ...............................1 - 4 Folding rear seat ...............................1 -[...]

WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. Y ou could also slide under the lap belt and receive serious internal injuries. ● For the most effective protecti[...]

Forward and backward Pull the center of the bar up and hold it while you slide the seat forward or backward to the desired position. Release the bar to lock the seat in position. Reclining T o recline the seatback, pull the lever up and lean back. T o bring the seatback forward, pull the lever up and lean your body forward. Release the lever to loc[...]

FRONT POWER SEA T ADJUSTMENT (for driver’s seat) Operating tips WARNING Before driving the vehicle, return the seat- back to an upright seating position after manually releasing it. Also, make sure the seat is locked in place. Failure to do so may cause the seat to move in a collision or sudden stop. This may result in damage to the seat or perso[...]

Seat lifter (if so equipped for driver’s seat) T ype A: Pull up or push down the adjusting lever to adjust the seat height until the desired position is achieved. T ype B: Push the switch up or down to adjust the angle and height of the seat cushion. Lumbar support (if so equipped for driver’s seat) The lumbar support feature provides lower bac[...]

FOLDING REAR SEA T Interior trunk access The trunk can be accessed from the passenger side of the rear seat for loading and unloading, as shown. 1. Move the front passenger seat to the most forward position. 2. Open the access cover on the rear parcel shelf. 3. Push down on the button 䊊 1 on the rear parcel shelf. 4. Fold down the passenger’s s[...]

T o fold down the driver’s side of the rear seat, open the trunk and pull on the strap 䊊 1 . The rear seats can be locked using the mechani- cal key to prevent unauthorized access. For more information on keys, refer to “Keys” in the “Pre- driving checks and adjustments” section of this manual. Center armrest Pull the armrest down until[...]

The illustration shows the seating positions equipped with head restraints. Cloth seat: The front seat head restraints are adjustable and removable. The rear head re- straints do not adjust or remove. Leather seat: The front and rear outboard head restraints are adjustable and removable. The cen- ter headrest is not removable and does not ad- just.[...]

T o raise the head restraint, pull it up. T o lower, push and hold the lock knob and push the head restraint down. Removal Use the following procedure to remove the ad- justable head restraints. 1. Pull the head restraint up to the highest position. 2. Push and hold the lock knob. 3. Remove the head restraint from the seat. 4. Store the head restra[...]

Install 1. Align the head restraint stalks with the holes in the seat. Make sure the head restraint is facing the correct direction. The stalk with the adjustment notches 䊊 1 must be installed in the hole with the lock knob 䊊 2 . 2. Push and hold the lock knob and push the head restraint down. 3. Properly adjust the head restraint before an occ[...]

WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly re- strained in the rear seat and, if appro- priate, in a child restraint. WARNING ● The seat belt should be properly ad- justed to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system a[...]

WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never put the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. ● Position the lap belt as low and snug as possible AROUND THE HIPS, NO T THE WAIST . A lap belt worn too [...]

PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug and always position the lap belt as low as possible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never run the lap/shoulder belt over your ab- dominal area. Contact your doctor for specific reco[...]

Fastening the seat belts 1. Adjust the seat. See “Seats” earlier in this section. 䊊 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. ● The retractor is designed to lock dur- ing a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and[...]

䊊 3 P osition the lap belt portion low and snug on the hips as shown. 䊊 4 Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the shoulder belt is routed over your shoulder and across your chest. The front passenger seat and the rear seating positions’ three-point seat belts have two modes of operation: ● Eme[...]

T o increase your confidence in the seat belts, check the operation as follows: ● Grasp the shoulder belt and pull forward quickly . The retractor should lock and re- strict further belt movement. If the retractor does not lock during this check or if you have any questions about seat belt opera- tion, see a NISSAN dealer. Shoulder belt height ad[...]

WARNING ● Only NISSAN seat belt extenders, made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts. ● Adults and children who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident. ● Never use seat[...]

There are three basic types of child restraint systems: ● Rear-facing child restraint ● Forward-facing child restraint ● Booster seat The proper restraint depends on the child’s size. Generally , infants up to about 1 year and less than 20 lbs (9 kg) should be placed in rear-facing child restraints. Forward-facing child restraints are avail[...]

properly , the booster seat should raise the child so that the shoulder belt is properly positioned across the chest and the top, middle portion of the shoulder. The shoulder belt should not cross the neck or face and should not fall off the shoul- der. The lap belt should lie snugly across the lower hips or upper thighs, not the abdomen. A booster[...]

– Infants and children should never be held on anyone’s lap. Even the stron- gest adult cannot resist the forces of a collision. – Do not put a seat belt around both a child and another passenger. – NISSAN recommends that all child restraints be installed in the rear seat. Studies show that children are safer when properly restrained in the[...]

● If the child restraint is compatible with your vehicle, place your child in the child restraint and check the various adjustments to be sure the child restraint is compatible with your child. Choose a child restraint that is designed for your child’s height and weight. Always follow all recommended procedures. All U.S. states and Canadian pro[...]

LA T CH lower anchor point locations The LA T CH anchors are located at the rear of the seat cushion near the seatback. A label is at- tached to the seatback to help you locate the LA T CH anchors. Installing child restraint LA T CH lower anchor attachments LA T CH compatible child restraints include two rigid or webbing-mounted attachments that ca[...]

T op tether anchor point locations The child restraint top tether strap must be used when installing the child restraint with the LA TCH lower anchor attachments or seat belts. See “In- stalling top tether strap” later in this section. If you have any questions when installing a top tether strap, consult your NISSAN dealer for details. Anchor p[...]

2. Secure the child restraint anchor attach- ments to the LA TCH lower anchors. Check to make sure the LA T CH attachment is prop- erly attached to the lower anchors. 3. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center[...]

5. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 2 through 4. REAR-F ACING CHILD RESTRAINT INST ALLA TION USING THE SEA T BEL TS WARNING The three-point seat belt with Automatic Locking Retractor (ALR) must be used when installing a child restraint. Failure to use the ALR[...]

Refer to all Warnings and Cautions in the “Child safety” and “Child restraints” sections before in- stalling a child restraint. Follow these steps to install a rear-facing child restraint using the vehicle seat belts in the rear seats: 1. Child restraints for infants must be used in the rear-facing direction and therefore must not be used i[...]

4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. 5. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seatback while pulling up on the seat belt. 6. After attaching the child restraint, test [...]

7. Check to make sure that the child restraint is properly secured prior to each use. If the seat belt is not locked, repeat steps 1 through 6. After the child restraint is removed and the seat belt fully retracted, the ALR mode (child restraint mode) is canceled. FORW ARD-F ACING CHILD RESTRAINT INST ALLA TION USING LA T CH Refer to all Warnings a[...]

3. The back of the child restraint should be secured against the vehicle seatback. If necessary , adjust or remove the head re- straint to obtain the correct child restraint fit. If the head restraint is removed, store it in a secure place. Be sure to reinstall the head restraint when the child restraint is removed. See “Head restraints” in thi[...]

7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 2 through 6. FORW ARD-F ACING CHILD RESTRAINT INST ALLA TION USING THE SEA T BEL TS WARNING The three-point seat belt with Automatic Locking Retractor (ALR) must be used when installing a child restraint. Failure to use the[...]

3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s in- structions for belt routing. If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anc[...]

6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt. 7. Tighten the tether strap according to the manufacturer’s instructions to remove any slack. 8. After attaching the child re[...]

10. If the child restraint is installed in the front passenger seat, place the ignition switch in the ON position. The front passenger air bag status light should illuminate. If this light is not illuminated, see “Front passenger air bag and status light” in this section. Move the child restraint to another seating position. Have the system che[...]

Booster seats of various sizes are offered by several manufacturers. When selecting any booster seat, keep the following points in mind: ● Choose only a booster seat with a label certifying that it complies with Federal Motor V ehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213. ● Check the booster seat in your vehicle to [...]

● Make sure the child’s head will be properly supported by the booster seat or vehicle seat. The seatback must be at or above the center of the child’s ears. For example, if a low back booster seat 䊊 1 is chosen, the vehicle seatback must be at or above the center of the child’s ears. If the seatback is lower than the center of the child?[...]

3. The booster seat should be positioned on the vehicle seat so that it is stable. If necessary , adjust or remove the head re- straint to obtain the correct booster seat fit. If the head restraint is removed, store it in a secure place. Be sure to reinstall the head restraint when the booster seat is removed. See “Head restraints” in this sec-[...]

PRECAUTIONS ON SUPPLEMENT AL RESTRAINT S Y STEM This Supplemental Restraint System (SRS) sec- tion contains important information concerning the following systems: ● Driver and passenger supplemental front- impact air bag (NISSAN Advanced Air Bag System) ● Front seat-mounted side-impact supple- mental air bag ● Roof-mounted curtain side-impac[...]

WARNING ● The front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower severity fron- tal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents. ● The front passenger air bag will not inflate if the passenger air bag status light is lit[...]

WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations. ARS1133 ARS1041 Safety—Seats, seat belts and supplemental restraint system 1-39[...]

ARS1042 ARS1043 ARS1044 1-40 Safety—Seats, seat belts and supplemental restraint system[...]

WARNING ● Children may be severely injured or killed when the front air bags, side air bags or curtain air bags inflate if they are not properly restrained. Pre-teens and children should be properly re- strained in the rear seat, if possible. ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the fron[...]

WARNING ● The seat belts, the side air bags and curtain air bags are most effective when you are sitting well back and upright in the seat with both feet on the floor. The side air bag and curtain air bag inflate with great force. Do not allow anyone to place their hand, leg or face near the side air bag on the side of the seatback of the front s[...]

WARNING ● When sitting in the rear seat, do not hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially careful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations ● Do not use seat covers on the front seat[...]

1. T op tether strap anchor 2. Rear seat belts 3. Roof-mounted curtain side-impact supplemental air bag 4. Front seat-mounted side-impact supple- mental air bag 5. Head restraints 6. Front seat belts 7. Side-impact pressure sensor (driver’s side shown; passenger’s side similar) 8. Supplemental front-impact air bags 9. Seats 10. Occupant classif[...]

● Do not place heavy loads heavier than 2.2 lb (1 kg) on the seatback, head re- straint or in the seatback pocket. ● Do not store luggage behind the seat that can press into the seatback. ● Do not position the front passenger seat so it contacts the rear seat. If the front seat does contact the rear seat, the air bag system may determine a se[...]

If you have any questions about your air bag system, please contact NISSAN or your NISSAN dealer. If you are considering modification of your vehicle due to a disability, you may also contact NISSAN. Contact information is contained in the front of this Owner’s Manual. When a front air bag inflates, a fairly loud noise may be heard, followed by t[...]

Status light The front passenger air bag status light is located near the climate controls. After the igni- tion switch is placed in the ⬙ ON ⬙ position, the front passenger air bag status light on the instru- ment panel illuminates for about 7 seconds and then turns off or remains illuminated depending on the front passenger seat occupied stat[...]

classification sensor. Other conditions could also result in air bag inflation, such as if a child is standing on the seat, or if two children are on the seat, contrary to the instructions in this manual. Always be sure that you and all vehicle occupants are seated and restrained properly . Using the passenger air bag status light, you can monitor [...]

● Immediately after inflation, several front air bag system components will be hot. Do not touch them; you may se- verely burn yourself. ● No unauthorized changes should be made to any components or wiring of the supplemental air bag system. This is to prevent accidental inflation of the supplemental air bag or damage to the supplemental air ba[...]

FRONT SEA T -MOUNTED SIDE- IMP ACT SUPPLEMENT AL AIR BAG AND ROOF-MOUNTED CURT AIN SIDE-IMP ACT SUPPLEMENT AL AIR BAG S Y STEMS The side air bags are located in the outside of the seatback of the front seats. The curtain air bags are located in the side roof rails. These systems are designed to meet voluntary guidelines to help reduce the risk of i[...]

● Right after inflation, several side air bag and curtain air bag system components will be hot. Do not touch them; you may severely burn yourself. ● No unauthorized changes should be made to any components or wiring of the side air bag and curtain air bag systems. This is to prevent damage to or accidental inflation of the side air bag and cur[...]

The pretensioners are part of the seat belt retrac- tor assembly . These seat belts are used the same way as conventional seat belts. When a pretensioner activates, smoke is re- leased and a loud noise may be heard. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking.[...]

If any of the following conditions occur, the front air bag, side air bag and curtain air bag and pretensioner systems need servicing: ● The supplemental air bag warning light re- mains on after approximately 7 seconds. ● The supplemental air bag warning light flashes intermittently. ● The supplemental air bag warning light does not come on a[...]

2 Instruments and controls Instrument panel ...................................2 - 2 Meters and gauges ................................2 - 3 Speedometer and odometer . . ...................2 - 4 T achometer ....................................2 - 4 Engine coolant temperature gauge ...............2 - 5 Fuel gauge ....................................[...]

Grocery hooks ................................ 2-42 Windows ........................................ 2-42 P ower windows ............................... 2-42 Moonroof (if so equipped) ......................... 2-45 Automatic moonroof ........................... 2-45 Interior light ...................................... 2-46 Console light ..........[...]

1. Instrument brightness control/T rip com- puter reset switch (P . 2-33, P . 2-4) 2. V ents (P . 4-20) 3. Headlight/fog light (if so equipped)/turn signal switch (P . 2-30) 4. Driver supplemental air bag/horn (P . 1-37, P . 2-34) 5. Meters and gauges (P . 2-3) 6. Paddle shift controls (if so equipped) (P . 5-15) 7. Windshield wiper/washer switch ([...]

22. V ehicle Dynamic Control OFF switch (P . 2-37) T runk opener (P . 3-27) Heated steering wheel switch (if so equipped) (P . 2-36) W arning system switch (if so equipped) (P . 2-36) * Refer to the Navigation System Owner’s manual (if so equipped) See the page number indicated in paren- theses for operating details. 1. T achometer 2. W arning/in[...]

SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed. Odometer/T win trip odometer The odometer 䊊 1 and the twin trip odometer 䊊 2 are displayed below the V ehicle Information Dis- play when the ignition switch is placed in the ON position. The odometer records the total distance the ve- hicle has been driven. The twin t[...]

ENGINE COOLANT TEMPERA TURE GAUGE The gauge indicates the engine coolant tempera- ture. The engine coolant temperature is within the normal range 䊊 1 when the gauge needle points within the zone shown in the illustration. The engine coolant temperature varies with the outside air temperature and driving conditions. CAUTION If the gauge indicates [...]

The indicates that the fuel-filler door is located on the driver’s side of the vehicle. CAUTION ● If the vehicle runs out of fuel, the Malfunction Indicator Light (MIL) may come on. Refuel as soon as possible. After a few driving trips. the light should turn off. If the light remains on after a few driving trips, have the ve- hicle inspected by[...]

pass will be calibrated once it has tracked three complete circles. COMP ASS DISPLA Y Press the button when the ignition switch is placed in the ON position. The direction will be displayed. Zone variation change procedure The difference between magnetic north and geo- graphical north is known as variance. In some areas, this difference can sometim[...]

● If a magnet is located near the com- pass or the vehicle is driven where the terrestrial magnetism is disturbed, the compass display may not indicate the correct direction. ● In places where the terrestrial magne- tism is disturbed, the correction of the direction starts automatically. Inaccurate compass direction: The compass display is equi[...]

● The compass may not indicate the correct compass point in tunnels or while driving up or down a steep hill. (The compass returns to the correct compass point when the ve- hicle moves to an area where the geomag- netism is stabilized.) CAUTION ● Do not install a ski rack, antenna, etc ., which are attached to the vehicle by means of a magnet. [...]

Anti-lock Braking System (ABS) warning light Seat belt warning light and chime Malfunction Indicator Light (MIL) or Brake warning light Supplemental air bag warning light Security indicator light Charge warning light Fog light indicator light (if so equipped) Side light and headlight indicator light (green) Low tire pressure warning light Front pas[...]

If an ABS malfunction occurs, the anti-lock func- tion is turned off. The brake system then operates normally , but without anti-lock assistance. See “Brake system” in the “Starting and driving” sec- tion. or Brake warning light This light functions for both the parking brake and the foot brake systems. Parking brake indicator When the igni[...]

The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly. After the ignition switch is placed in the ON position, this light illuminates for about 1 second and turns off. Low tire pressure warning: If the vehicle is being driven with low tire pressure, the warning light will illuminate. A[...]

● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. ● Replacing ti[...]

Supplemental air bag warning light When the ignition switch is placed in the ON or ST ART position, the supplemental air bag warn- ing light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the front air bag, side air bag, curtain air bag, and preten- sioner systems [...]

After a few driving trips, the light should turn off if no other potential emission control system malfunction exists. If this indicator light comes on steady for 20 sec- onds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/maintenance test. See “R[...]

Side light and headlight indicator light (green) The side light and headlight indicator light illumi- nates when the side light or headlight position is selected. See “Headlight and turn signal switch” later in this section for further details. Slip indicator light This indicator will blink when the VDC system or the traction control system is [...]

The vehicle information display is located to the left of the speedometer. It displays such items as: ● V ehicle settings ● T rip computer information ● Cruise control system information ● NISSAN Intelligent K ey® operation informa- tion ● Indicators and warnings (if so equipped) ● Tire Pressure information (if so equipped) ● Audio i[...]

SETTINGS The setting mode allows you to change the infor- mation displayed in the vehicle information dis- play: ● Driver Assistance (if so equipped) ● Main Menu Selection ● Body Color ● Maintenance ● Alarms ● V ehicle Settings ● Language ● Unit ● Welcome Effects ● Factory Reset Driver Assistance (if so equipped) T o change the [...]

From the “Main Menu Selection” select “Naviga- tion” to display in the vehicle information display when turn-by-turn is used and the ignition is placed in the ON position. Fuel Economy The fuel economy can be enabled/disabled to display in the vehicle information display when the ignition switch is placed in the ON position. From the “Mai[...]

WARNING The tire replacement indicator is not a substitute for regular tire checks, includ- ing tire pressure checks. See “Changing Wheels and Tires” in “Maintenance & Do- It- Y ourself” section. Many factors includ- ing tire inflation, alignment, driving habits and road conditions affect tire wear and when tires should be replaced. Set[...]

Light Sensitivity (if so equipped) The light sensitivity can be set to illuminate earlier based on the brightness outside the vehicle. From the Vehicle Settings menu, select “Light Sensitivity” . Use the ENTER button to change the sensitivity . Light Off Delay (if so equipped) The duration of the automatic headlights can be changed from 0 to 18[...]

Units The units that are shown in the vehicle informa- tion display can be changed: ● Mileage ● Tire pressures ● T emperature Use the , , and the ENTER buttons to select and change the units of the vehicle infor- mation display. The units of the navigation screen can be changed independently of the vehicle information display . For vehicles e[...]

VEHICLE INFORMA TION DISPLA Y W ARNINGS AND INDICA T ORS 1. No Key Detected 2. Key ID Incorrect 3. Shift to Park 4. Push ignition to OFF 5. Key Battery Low 6. Engine start operation for Intelligent K ey sys- tem 7. Release parking brake 8. Low Fuel 9. Low W asher Fluid 10. Door Open 11. T runk Open LIC2343 Instruments and controls 2-23[...]

12. Timer Alert – Time for a driver break? 13. Low Outside T emperature 14. Power will turn off to save the battery 15. CVT Error 16. Reminder: T urn OFF headlights 17. Low Oil Pressure 18. Key Registration Complete 19. Tire Pressure Low - Add Air (if so equipped) 20. TPMS Error 21. Remote Start (if so equipped) 22. Loose Fuel Cap No Key Detected[...]

Door Open This warning illuminates when a door has been opened when the engine is running. T runk Open This warning illuminates when the trunk has been opened when the engine is running. Timer Alert – Time for a driver break? This indicator appears when the set time is reached. The time can be set up to 6 hours. For setting the timer see, “Time[...]

Y our vehicle may has two types of security sys- tems: ● V ehicle security system ● NISSAN Vehicle Immobilizer System VEHICLE SECURITY S Y STEM The vehicle security system provides visual and audible alarm signals if someone opens the doors, trunk lid or the hood when the system is armed. It is not, however, a motion detection type system that [...]

The alarm is activated by: ● opening the door or trunk lid without using the key or Intelligent Key (even if the door is unlocked by releasing the door inside lock switch) . How to stop an activated alarm The alarm stops only by unlocking the driver’s door or the trunk lid with the key, pressing the button on the Intelligent K ey, or press- ing[...]

WARNING In freezing temperatures the washer solu- tion may freeze on the window and ob- scure your vision which may lead to an accident. Warm the window with the de- froster before you wash the window. CAUTION ● Do not operate the washer continu- ously for more than 30 seconds. ● Do not operate the washer if the reser- voir tank is empty. ● D[...]

䊊 2 Low (L O) — continuous low speed operation 䊊 3 High (HI) — continuous high speed opera- tion Push the lever up 䊊 4 to have one sweep opera- tion (MIST) of the wiper. Pull the lever toward you 䊊 5 to operate the washer. The wiper will also operate several times. T o defrost the rear window glass and outside mirrors (if so equipped) ,[...]

XENON HEADLIGHTS (if so equipped) WARNING c HIGH VOL TAGE ● When xenon headlights are on, they produce a high voltage. T o prevent an electric shock, never attempt to modify or disassemble. Always have your xe- non headlights replaced at a NISSAN dealer. ● X enon headlights provide considerably more light than conventional head- lights. If they[...]

HEADLIGHT CONTROL SWIT CH Lighting 䊊 1 When turning the switch to the posi- tion, the front parking, tail, license plate and instrument panel lights come on. 䊊 2 When turning the switch to the posi- tion, the headlights come on and all the other lights remain on. CAUTION Use the headlights with the engine run- ning to avoid discharging the vehi[...]

NO TE: Autolight activation sensitivity and the time delay for autolight shutoff can be ad- justed. See “Vehicle information display” in this section. T o turn on the autolight system: 1. T urn the headlight switch to the AUT O posi- tion 䊊 1 . 2. T urn the ignition switch to ON. 3. The autolight system automatically turns the headlights on a[...]

CAUTION Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery. DA YTIME RUNNING LIGHT S Y STEM (Canada only) The headlights automatically illuminate at a re- duced intens[...]

TURN SIGNAL SWIT CH T urn signal 䊊 1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically. Lane change signal 䊊 2 T o signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch. The turn signal will[...]

The front seats are warmed by built-in heaters. 1. Start the engine. 2. Push the L O or HI position of the switch, as desired. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on. 3. When the seat is w[...]

The heated steering wheel system is designed to operate only when the surface temperature of the steering wheel is below approximately 68°F (20°C) . Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light will come on. If the surface temperature of the steering wheel is below 68°F (20°C) , t[...]

twice and the BSW indicator light will flash. For additional information, see “Blind Spot Warning (BSW) System / Lane Departure Warning (LDW) System” in the “Starting and driving” section. The LDW system will sound a warning chime and the LDW indicator light (orange) in the vehicle information display blinks to alert the driver if the vehic[...]

CAUTION ● The outlet and plug may be hot during or immediately after use. ● Only certain power outlets are designed for use with a cigarette lighter unit. Do not use any other power outlet for an accessory lighter. See your NISSAN dealer for additional information. ● Do not use with accessories that ex - ceed a 12 volt, 120W (10A) power draw.[...]

SEA TBACK POCKETS (if so equipped) The seatback pockets are located on the back of the driver’s (if so equipped) and passenger’s seats. The pockets can be used to store maps. SUNGLASSES HOLDER T o open the sunglasses holder, push and release. Only store one pair of sunglasses in the holder. WARNING Keep the sunglasses holder closed while drivin[...]

CUP HOLDERS The rear center cup holders are located in the rear fold-down armrest. CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. ● Use only soft cups in the cup holder. Hard objects can injure you in an accident. Soft bottle [...]

GL OVE BOX Open the glove box by pulling the handle. Use the master key when locking 䊊 1 or unlocking 䊊 2 the glove box. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. CONSOLE BOX Upper half Pull up on the driver’s side latch to open the upper half of the console box. The upper half of [...]

GROCER Y HOOKS The grocery hooks are located in the trunk and can be used to hang a standard size plastic grocery bag. CAUTION Do not apply a total load of more than 20 lbs (9 kg) to a single grocery hook. POWER WINDOWS WARNING ● Make sure that all passengers have their hands, etc . inside the vehicle while it is in motion and before closing the [...]

Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close all of the windows. T o open a window , push the switch to the first detent and continue to hold down until the de- sired window position is reached. T o close a window , pull the switch to the first detent and continue to hold up until [...]

Automatic operation T o fully open a window equipped with automatic operation, press the window switch down to the second detent and release it; it need not be held. The window automatically opens all the way. T o stop the window, lift the switch up while the window is opening. T o fully close a window equipped with automatic operation, pull the sw[...]

AUT OMA TIC MOONROOF The moonroof will only operate when the ignition switch is placed in the ON position. The auto- matic moonroof is operational for a period of time, even if the ignition switch is placed in the ACC or OFF position. If the driver’s door or the front passenger’s door is opened during this period of time, the power to the moonr[...]

When tilting down: If the control unit detects something caught in the moonroof as it tilts down, the moonroof will im- mediately tilt up. If the auto-reverse function malfunctions and re- peats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds after it happens; the moonroof will fully close gradually . Make sur[...]

NO TE: The step lights illuminate when the driver and passenger doors are opened regard- less of the interior light switch position. These lights will turn off automatically after a period of time while doors are open to prevent the battery from becoming dis- charged. CAUTION Do not use for extended periods of time with the engine stopped. This cou[...]

Push the button to turn the map lights on. T o turn them off, press the button again. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. The light illuminates when the trunk lid is opened. When the trunk lid is closed, the light goes off. The light will go off after a period of time i[...]

WARNING ● Do not use the HomeLink® Universal T ransceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards. (These standards be- came effective for opener models manufactured after April 1, 1982) . A ga- rage door opener which cannot detect an object in the path of a closing garage[...]

3. Press and hold the programmed HomeLink® button and observe the indica- tor light. ● If the indicator light 䊊 1 is solid/continuous, programming is complete and your device should acti- vate when the HomeLink® button is pressed and released. ● If the indicator light 䊊 1 blinks rapidly for two seconds and then turns to a solid/continuous[...]

press and hold the desired HomeLink® but- ton while you press and re-press (“cycle”) your hand-held transmitter every two sec- onds until the frequency signal has been learned. The HomeLink® indicator light will flash slowly and then rapidly after several seconds upon successful training. DO NO T release until the HomeLink® indicator light f[...]

REPROGRAMMING A SINGLE HOMELINK® BUTT ON T o reprogram a HomeLink® Universal T rans- ceiver button, complete the following: 1. Press and hold the desired HomeLink® but- ton. DO NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink® button, proceed with “Pro- gramming HomeLink®” [...]

3 Pre-driving checks and adjustments K e y s .............................................3 - 2 NISSAN Intelligent K ey® ........................3 - 2 NISSAN Vehicle Immobilizer System keys .........3 - 4 Doors ............................................3 - 4 Locking with key ................................3 - 4 Locking with inside lock knob ...[...]

1. Intelligent K ey (2 sets) 2. Mechanical key 3. K ey number plate (1 plate) NISSAN INTELLIGENT KEY® Y our vehicle can only be driven with the Intelligent K eys which are registered to your vehicle’s Intel- ligent Key system components and NISSAN V e- hicle Immobilizer System components. As many as 4 Intelligent Keys can be registered and used [...]

● Do not place the Intelligent Key near equipment that produces a magnetic field, such as a TV, audio equipment and personal computers. If an Intelligent Key is lost or stolen, NISSAN recommends erasing the ID code of that Intelligent Key from the vehicle. This may prevent the unauthorized use of the Intelligent Key to operate the vehicle. For in[...]

NISSAN VEHICLE IMMOBILIZER S Y STEM KEY S Y ou can only drive your vehicle using the master keys which are registered to the NISSAN V ehicle Immobilizer System components in your vehicle. The master key can be used for all the locks. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key , the key number is n[...]

Opening and closing windows (if so equipped) The driver’s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. ● T o open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. ● T o close the windows, turn the drive[...]

Lockout protection When the power door lock switch is moved to the lock position and any door is open, all doors will lock and unlock automatically . With the Intelligent K ey left in the vehicle and any door is open, all doors will unlock automatically and a chime will sound after the door is closed. These functions help to prevent the Intelligent[...]

WARNING ● Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufac- turer for the possible influences before use. ● The Intelligent Key transmits radio waves when the buttons are pressed. The FAA advises the radio waves may affect aircraft navigation and commu[...]

CAUTION Listed below are conditions or occur- rences which will damage the Intelligent Key: ● Do not allow the Intelligent Key, which contains electrical components, to come into contact with water or salt water. This could affect the system function. ● Do not drop the Intelligent Key. ● Do not strike the Intelligent Key sharply against anoth[...]

When the Intelligent Key battery is discharged or strong radio waves are present near the operat- ing location, the Intelligent K ey system’s operat- ing range becomes narrower, and the Intelligent K ey may not function properly . The operating range is within 31.50 in (80 cm) from each request switch 䊊 1 . If the Intelligent Key is too close t[...]

NISSAN INTELLIGENT KEY® OPERA TION Y ou can lock or unlock the doors without taking the key out of your pocket or bag. When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch within the range of opera- tion. Locking doors 1. Move the shift selector to the P (Park) posi- tion, place th[...]

● Doors do not lock with the door handle request switch with the Intelligent Key inside the vehicle and a beep sounds to warn you. However, when an Intelligent K ey is inside the vehicle, doors can be locked with an- other Intelligent K ey . CAUTION ● After locking the doors using the re- quest switch, make sure that the doors have been securel[...]

All doors will be locked automatically unless one of the following operations is performed within 1 minute after pushing the request switch: ● Opening any door. ● Pushing the ignition switch. The interior light timer illuminates for a period of time when a door is unlocked and the room light switch is in the DOOR position. The interior light ca[...]

When all doors are locked and the trunk lid is closed with the Intelligent Key inside the trunk, the outside buzzer will sound and the trunk will open. HOW T O USE THE REMO TE KEYLESS ENTRY FUNCTION The remote keyless entry function can operate all door locks using the remote keyless function of the Intelligent Key . The remote keyless function can[...]

Unlocking doors 1. Press the button on the Intelligent Ke y. 2. The hazard warning lights flash once. 3. Press the button again within 5 sec- onds to unlock all doors. NO TE: The unlocking operation can be changed in Selective door unlock in the Vehicle Set- tings of the vehicle information display. For additional information, see “V ehicle infor[...]

Releasing the trunk lid Press the button for longer than 0.5 sec- onds to open the trunk lid. The trunk release button will not operate when the ignition switch is in the ON position or when the trunk cancel switch is in the OFF position. See “Cancel switch” in this section. Using the panic alarm If you are near your vehicle and feel threatened[...]

Answer back horn feature If desired, the answer back horn feature can be deactivated using the Intelligent Key . When de- activated and the L OCK button is pushed the hazard indicator flashes twice and when the UNL OCK button is pushed, nei- ther the hazard indicator nor the horn operates. NO TE: If you change the answer back horn and light flash f[...]

TROUBLESHOO TING GUIDE V erify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent K ey is in range or inside the vehicle, the vehicle system may respond differently than expected. Symptom Possible Cause Remedy When stopping the engine The Shift to Park warning appears in the display and the inside warni[...]

WARNING ● Radio waves could adversely affect elec- tric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use. ● The Intelligent Key transmits radio waves when the buttons are pressed. The FAA advises the radio waves may affect air- craft navigation and com[...]

CAUTION Listed below are conditions or occur- rences which will damage the Intelligent Key: ● Do not allow the Intelligent Key, which contains electrical components, to come into contact with water or salt water. This could affect the system function. ● Do not drop the Intelligent Key. ● Do not strike the Intelligent Key sharply against anoth[...]

Locking doors 1. Place the ignition switch in the L OCK posi- tion. 2. Close all doors. 3. Press the button on the Intelligent Ke y. 4. The hazard warning lights flash twice and the horn beeps once. 5. All doors will be locked. CAUTION After locking the doors using the Intelli- gent Key, be sure that the doors have been securely locked by operating[...]

NO TE: The unlocking operation can be changed in Selective door unlock in the Vehicle Set- tings of the vehicle information display. For additional information, see “V ehicle infor- mation display” in the “Instruments and controls” section of this manual. All doors will be locked automatically unless one of the following operations is perfo[...]

Using the panic alarm If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention by pressing and holding the button on the Intelligent Key for longer than 0.5 seconds. The panic alarm and headlights will stay on for a period of time. The panic alarm stops when: ● It has run for a period of time, or ● An[...]

W ARNING SIGNALS T o help prevent the vehicle from moving unex- pectedly by erroneous operation of the Intelligent K ey or to help prevent the vehicle from being stolen, a chime or buzzer sounds from inside and outside the vehicle and a warning is displayed in the instrument panel. When a chime or beep sounds or a warning is displayed, be sure to c[...]

TROUBLESHOO TING GUIDE V erify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent K ey is in range or inside the vehicle, the vehicle system may respond differently than expected. Symptom Possible Cause Remedy When stopping the engine The Shift to Park warning appears in the display and the inside warni[...]

The button will be on the NISSAN Intelli- gent Key® if the vehicle has remote engine start. This feature allows the engine to start from out- side the vehicle. The following features may be affected when the remote start feature is used: ● V ehicles with manual or automatic climate control systems will default to the last used heating or cooling[...]

EXTENDING ENGINE RUN TIME The remote start feature can be extended one time by performing the steps listed in “Remote starting the vehicle” in this section. Run time will be calculated as follows: ● The first 10 minute run time will start when the remote start function is performed. ● The second 10 minutes will start immedi- ately when the [...]

䊊 1 Pull the hood lock release handle located below the driver’s side instrument panel; the hood springs up slightly. 䊊 2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood. 䊊 3 Remove the support rod from the clamp. 䊊 4 Insert the support rod into the slot on the passenger side fend[...]

● Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in- jured. Keep the car locked, with the rear seatback and trunk lid securely latched when not in use, and prevent children’s access to car keys. T o open the trunk lid perform one of the following a[...]

Cancel switch When the switch, located inside the glove box, is in the OFF position, the power to the trunk lid will be cancelled. The trunk lid cannot be opened when: ● using the trunk lid release switch, ● the trunk open request switch (if so equipped) is pushed, when the Intelligent K ey is in range of the vehicle or ● the HOLD button on t[...]

OPENER OPERA TION The fuel-filler door release is located below the instrument panel. T o open the fuel-filler door, pull the release. T o lock, close the fuel-filler door securely . FUEL -FILLER CAP WARNING ● Gasoline is extremely flammable and highly explosive under certain condi- tions. Y ou could be burned or seriously injured if it is misuse[...]

● The LOOSE FUEL CAP warning will ap- pear if the fuel-filler cap is not properly tightened. It may take a few driving trips for the message to be displayed. Failure to tighten the fuel-filler cap properly after the LOOSE FUEL CAP warning ap- pears may cause the Malfunction Indicator Light (MIL) to illuminate. ● Failure to tighten the fuel-fill[...]

TIL T OPERA TION Pull the lock lever down 䊊 1 and adjust the steer- ing wheel up or down 䊊 2 to the desired position. Push the lock lever up 䊊 1 firmly to lock the steering wheel in place. WARNING Do not adjust the steering wheel while driving. Y ou could lose control of your vehicle and cause an accident. TELESCOPIC OPERA TION Pull the lock [...]

䊊 1 T o block glare from the front, swing down the main sun visor. 䊊 2 T o block glare from the side, remove the main sun visor from the center mount and swing the visor to the side. 䊊 3 T o extend (if so equipped) the sun visor, slide in or out as needed. CAUTION ● Do not store the sun visor before return- ing the extension to its original[...]

AUT OMA TIC ANTI-GLARE REARVIEW MIRROR (if so equipped) The inside mirror is designed so that it automati- cally dims during night time conditions and ac- cording to the intensity of the headlights of the vehicle following you. The automatic anti-glare feature is activated when the ignition switch is in the ON position. The indicator light will ill[...]

OUTSIDE MIRRORS WARNING ● Do not adjust the mirrors while driving. Y ou could lose control of your vehicle and cause an accident. ● Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your[...]

MEMO 3-36 Pre-driving checks and adjustments[...]

4 Monitor, climate, audio, phone and voice recognition systems Control panel buttons — color screen with Navigation System (if so equipped) ..................4 - 4 How to use the touch screen ....................4 - 5 How to use the BACK button ....................4 - 7 How to use the MENU button ....................4 - 7 button .................[...]

iP od®* player operation with Navigation System (if so equipped) ........................ 4-62 Bluetooth® streaming audio without Navigation System (T ype A) (if so equipped) ...... 4-65 Bluetooth® streaming audio without Navigation System (T ype B) (if so equipped) ...... 4-66 Bluetooth® streaming audio with Navigation System (if so equipped) [...]

Ending a call ................................. 4-105 T ext messaging ............................... 4-105 Bluetooth settings ............................ 4-107 Phone settings ............................... 4-108 NISSAN Voice Recognition System (if so equipped) ................................. 4-109 Using the system .............................[...]

WARNING ● Positioning of the heating or air condi- tioning controls and display controls should not be done while driving in or- der that full attention may be given to the driving operation. ● Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice a[...]

9. button** 10. CAMERA button * For information regarding the Navigation system control buttons, refer to the separate Navigation System Owner’s Manual. ** For information regarding the Bluetooth® Hands-Free Phone System control button, see “Bluetooth® Hands-Free Phone System” in this section. When you use this system, make sure the engine [...]

T ouch screen operation Selecting the item: T ouch an item to select. For example, to select the “ Audio” key, touch the “Audio” key 䊊 1 on the screen. Adjusting the item: For screens where an item can be adjusted incre- mentally , such as when adjusting the bass and treble for the audio system, touch the “+” key 䊊 1 or the “ ⫺ [...]

Inputting characters: T ouch the letter key 䊊 1 . There are some options available when inputting characters. ● 123 / ABC: Changes the available character set to num- bers. ● Space: Inserts a space. ● Delete: Deletes the last inputted character with one touch. T ouch and hold the “Delete” key to delete all of the characters. ● OK: Com[...]

3. Select the desired item. Audio For audio setup, refer to “ Audio system” in this section. Navigation Refer to the separate Navigation System Own- er’s Manual for information regarding this item. Phone & Bluetooth For information regarding the Bluetooth® Hands-Free Phone System, see “Bluetooth® Hands-Free Phone System” in this sec[...]

Display: Select the “Display” key to adjust the appearance of the display. The following settings can be adjusted: Brightness The brightness of the display can be set to V ery Bright, Bright, Default, Dark or V ery Dark. T ouch the “Brightness” key to cycle through the options. Display Mode The display can be adjusted to fit the level of li[...]

Clock Mode Select the mode for the clock. “Auto” uses the system’s GPS to automatically maintain the time. “Manual” allows you to set the clock using the “Set Clock Manually” key. “Time Zone” maintains the time based upon the zone selected when selecting the “Time Zone” key . Set Clock Manually When this setting is activated, [...]

message appears on the screen or a button on the unit (such as the button) is pressed and held for two seconds. Reset all settings/memory: Select the “Reset All Settings/Memory” key to return all settings to default and to clear the memory . Info For information about the “Info” key , see the separate Navigation System Owner’s Manual. XM [...]

HOW T O READ THE DISPLA YED LINES Guiding lines which indicate the vehicle width and distances to objects with reference to the vehicle body line 䊊 A are displayed on the monitor. Distance guide lines: Indicate distances from the vehicle body. ● Red line 䊊 1 : approx. 1.5 ft (0.5 m) ● Y ellow line 䊊 2 : approx. 3 ft (1 m) ● Green line ?[...]

HOW T O P ARK WITH PREDICTED COURSE LINES (Navigation System only) WARNING ● Always turn and check that it is safe to do so before backing up. Always back up slowly. ● Use the displayed lines as a reference. The lines are highly affected by the number of occupants, fuel level, vehicle position, road conditions and road grade. ● If the tires a[...]

3. Slowly back up the vehicle, adjusting the steering wheel so that the predicted course lines 䊊 B enter the parking space 䊊 C . 4. Maneuver the steering wheel to make the vehicle width guide lines 䊊 D parallel to the parking space 䊊 C while referring to the pre- dicted course lines. 5. When the vehicle is parked in the space completely , m[...]

the hill is the place 䊊 B . Note that any object on the hill is further than it appears on the monitor. Backing up on a steep downhill When backing up the vehicle down a hill, the distance guide lines and the vehicle width guide lines are shown farther than the actual distance. For example, the display shows 3 ft (1.0 m) to the place 䊊 A , but [...]

Backing up near a projecting object The predicted course lines 䊊 A do not touch the object in the display . However, the vehicle may hit the object if it projects over the actual backing up course. Backing up behind a projecting object The position 䊊 C is shown farther than the position 䊊 B in the display. However, the position 䊊 C is actua[...]

WARNING ● The MOD system is not a substitute for proper vehicle operation and does not prevent contact with the objects sur- rounding the vehicle. When maneuver- ing, always use the outside mirror and rear view mirror and turn and look to check the surroundings to make sure it is safe to maneuver. ● The MOD system is not designed to detect surr[...]

– When there is blinking source of light. – When strong light such as another vehicle’s headlight or sunlight is present. – When camera orientation is not in its usual position, such as when mirror is folded. – When there is dirt, water drops or snow on the camera lens. – When the position of the moving ob- jects in the display is not c[...]

4. Adjust the level using the TUNE-SCROLL knob and then press the ENTER/SETTING button to apply the adjustment. ● Do not adjust the Brightness or Contrast of the RearView Monitor while the vehicle is moving. For vehicles with Navigation System: 1. Press the MENU button. 2. Select the “Settings” key. 3. Select the “System” key. 4. Select t[...]

● When strong light directly enters the cam- era, objects may not be displayed clearly . ● V ertical lines may be seen in objects on the screen. This is due to strong reflected light from the bumper. This is not a malfunction. ● The screen may flicker under fluorescent light. This is not a malfunction. ● The colors of objects on the RearVie[...]

WARNING ● The air conditioner cooling function op- erates only when the engine is running. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot[...]

1. Fan speed control / system OFF dial / air conditioning (A/C) button 2. Air flow control buttons 3. T emperature control dial / MAX A/C button 4. Air recirculation button 5. Rear window defroster button 6. Front windshield defrost button CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed. Air flow cont[...]

Air recirculation button On position (Indicator light on) : Interior air is recirculated inside the vehicle. Press the button to the ON position when: ● driving on a dusty road. ● to prevent traffic fumes from entering pas- senger compartment. ● for maximum cooling when using the air con- ditioner. The air recirculation function does not oper[...]

● When the position is selected, the air conditioner automatically turns on (the indi- cator light on the button will come on) if the outside temperature is more than 36°F (2°C) . This dehumidifies the air which helps defog the windshield. The mode au- tomatically turns off, allowing outside air to be drawn into the passenger compartment to fur[...]

4. Push the button. The indicator light comes on. 5. T urn the temperature control dial to the de- sired position. Dehumidified defogging This mode is used to defog the windows and dehumidify the air. 1. Press the air flow control button. 2. T urn the fan control dial to the desired posi- tion. ● When the or are selected, the air conditioner auto[...]

LHA2284 LHA2285 4-26 Monitor, climate, audio, phone and voice recognition systems[...]

LHA2286 LHA2287 Monitor, climate, audio, phone and voice recognition systems 4-27[...]

LHA2288 4-28 Monitor, climate, audio, phone and voice recognition systems[...]

1. (front defroster) button 2. T emperature control dial (driver’s side)/ AUT O (automatic) climate control but- ton 3. Display screen 4. T emperature control dial (passenger’s side)/DUAL (passenger’s side tempera- ture control) button 5. Fresh air intake button 6. Air recirculation button 7. A/C (air conditioner) button 8. MODE (manual air f[...]

AUT OMA TIC OPERA TION Cooling and/or dehumidified heating (AUT O) This mode may be used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically. 1. Press the AUTO button on. (The indicator on the button will illuminate and AUTO will be displayed.) 2. T u[...]

The air recirculation cannot be activated when the air conditioner is in the front defrosting mode or the front defrosting and foot out- let mode. Fresh air intake Press the fresh air intake button to draw outside air into the passenger compartment. The indicator light on the button will come on. Automatic intake air control In the AUT O mode, the [...]

The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to [...]

Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) , static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response. Multipath reception: Because of the reflective characteri[...]

Compact disc (CD) player CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD player. ● T rying to load a CD with the CD door closed could damage the CD and/or CD player. ● Only one CD can be loaded into the CD player at a time. ● Only use high quality 4.7 in (12 cm) round disc s that have the ?[...]

Compact disc with MP3 or WMA (if so equipped) T erms: ● MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near “CD quality” sound, but at a fraction of the size of normal audio files. MP3 conversion of an audio track from CD-ROM can red[...]

Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. ● The names of folders not containing MP3 or WMA files are not shown in the display. ● If there is a file in the top level of the disc, “Root Folder” is displayed. ● The playback order is the order in which the files were written by the writing software.[...]

Specification chart : Supported media CD, CD-R, CD-RW Supported file systems ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. Supported versions*1 MP3 V ersion MPEG1, MPEG2, MPEG2.5 Sampling frequency 8 kHz - 48 kHz Bit rate 8 kbps - 320 kbps, VBR WMA V ersion WMA7, WMA8, WMA9 Sampling fr[...]

T roubleshooting guide: Symptom Cause and Countermeasure Cannot play Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the CD player wil[...]

USB (Universal Serial Bus) memory (if so equipped) WARNING Do not connect or disconnect the USB device while driving. Doing so can be a distraction. If distracted you could lose control of your vehicle and cause an acci- dent or serious injury. CAUTION ● Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-dow[...]

● Do not connect a USB device if a connector, cable or USB port is wet. Allow the connector, cable, and USB port to dry completely before connecting the USB device. (W ait for 24 hours or more until it is dry.) If the connec- tor and USB port are exposed to fluids other than water, evaporative residue may cause a short circuit between the connect[...]

1. CD eject button 2. CD insert slot 3. SCAN button 4. DISP button 5. RPT/RDM button 6. TUNE/FOLDER knob / MENU button 7. AUX IN jack 8. AUX button 9. CD button 10. AM button 11. FM button 12. VOL (volume) control knob / power but- ton 13. Station select (1 - 6) buttons 14. TRACK button 15. SEEK button FM/AM RADIO WITH COMP ACT DISC (CD) PLA YER (i[...]

MENU button (Bass, T reble, Balance, Fade, Speed Sensitive V olume and Clock) : Press the MENU button to change the mode as follows: Bass → T reble → Balance → Fade → Spd. Sen. V ol. (Speed Sensitive V olume) → AUX IN V olume → Clock → Clock Adjust T o adjust the Bass, T reble, Fade and Balance, press the MENU button until the desired[...]

The FM stereo indicator (ST) illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception. SEEK and TRACK (tuning) buttons: Press the SEEK button to tune from low to high frequencies and stop at the next broadcast- ing station. Press the TRACK button to tune from[...]

When the TRACK button is pressed, the track being played returns to the beginning. Press the TRACK button several times to skip back several tracks. Each time the button is pressed the CD moves back one track. RPT/RDM button: Press the RPT/RDM button while a compact disc is playing to change the play pattern as follows: CD: TRACK REPEA T → DISC R[...]

1. CD eject button 2. XM button* 3. Display screen 4. CD insert slot 5. SEEK button 6. SCAN button 7. CA T button 8. BACK button 9. iPod MENU button 10. TUNE/SCROLL knob, ENTER/SETTING button 11. AUX IN jack 12. Station select (1 - 6) buttons 13. RDM button 14. RPT button 15. VOL (volume) knob / ON-OFF button 16. DISP button 17. CD•AUX button 18.[...]

FM/AM/SA T RADIO WITH COMP ACT DISC (CD) PLA YER (T ype A) (if so equipped) For all operation precautions, see “ Audio opera- tion precautions” in this section. Audio main operation VOL (volume) knob / ON-OFF button: Place the ignition switch in the ACC or ON position and press the VOL (volume) knob / ON-OFF button while the system is off to ca[...]

Brightness and Contrast Adjust the brightness or contrast to adjust the appearance of the display screen. Clock Adjust Press the ENTER button to highlight the hours or minutes and then use the TUNE/SCROLL knob to adjust the value. Press the ENTER button again to set the value. On-Screen Clock Select “ON” or “OFF” to control whether or not t[...]

When the XM button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. The last station played will also come on when the VOL/ON·OFF control knob is pressed ON. *When the XM button is pressed, the satellite radio reception will not be available unless an optional satellite receiver [...]

SEEK/CA T button: Press the SEEK/CA T button while a CD or MP3/WMA CD is playing to return to the begin- ning of the current track. Press the SEEK/CA T button several times to skip backward sev- eral tracks. Press the SEEK/CA T button while a CD or MP3/WMA CD is playing to advance one track. Press the SEEK/CA T button several times to skip forward [...]

When the button is pressed twice with a compact disc loaded, the compact disc will be ejected further for easier CD removal. If the disc is not removed within 20 seconds, the disc will reload. Additional features For more information about the iPod® player available with this system, see “iPod® player operation without Navigation System” in t[...]

10. Forward seek button 11. Backward seek button 12. CD button 13. FM-AM button 14. XM button *No satellite radio reception is available when the XM button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and an SiriusXM Satellite Radio service subscription is active. Satellite radio is not [...]

Speed Sensitive V ol.: Controls the level to which the volume is adjusted as the vehicle’s driving speed changes. Choose a setting or choose “0” to disable the feature en- tirely . AUX V olume Level: Controls the volume level of incoming sound when an auxiliary device is connected to the system. Available options are Low, Medium and High. XM [...]

If a compact disc is playing when the XM button is pressed, the compact disc will automatically be turned off and the last radio station played will come on. While the radio is in XM mode, the operation can be controlled through the touchscreen. T ouch the “Channels” key to display a list of channels. T ouch a channel displayed on the list to c[...]

T uning with the TUNE/SCROLL knob: The radio can also be manually tuned using the TUNE/SCROLL knob. When in FM or AM mode, turn the TUNE/SCROLL knob to the left for lower frequencies or to the right for higher frequencies. When in XM mode, turn the TUNE/SCROLL knob to change the channel. SEEK tuning: When in FM or AM mode, press the seek buttons or[...]

CD/MP3 display mode While listening to a CD or an MP3/WMA CD, certain text may be displayed (when a CD en- coded with text is being used) . Depending on how the CD or MP3/WMA CD is encoded, the text is displayed listing the artist, album and song title. There are other keys displayed on the screen when a CD is playing: Random: T ouch the “Random?[...]

playing, touching the “Browse” key will also list the folders on the disc. Follow the procedure for selecting a song with the touchscreen to choose a folder. SEEK (Reverse or Fast Forward) buttons: Press and hold the seek buttons or for 1.5 seconds while the compact disc is playing to reverse or fast forward the track being played. The compact [...]

USB INTERF ACE (models without Navigation System) (if so equipped) Connecting a device to the USB input jack CAUTION ● Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the USB device and the port. Make sure that the USB device is con- nected correctly into the USB port. (Some [...]

SEEK/CA T buttons: Press the SEEK/CA T button while an au- dio file on the USB device is playing to return to the beginning of the current track. Press the SEEK/CA T button several times to skip backward several tracks. Press the SEEK/CA T button while an au- dio file on the USB device is playing to advance one track. Press the SEEK/CA T button sev[...]

Connecting a device to the USB input jack CAUTION ● Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the USB device and the port. Make sure that the USB device is con- nected correctly into the USB port. (Some USB devices come with a mark as a guide. Make sure that the mark is[...]

Press the button while an audio file on the USB device is playing to advance one track. Press the button several times to skip for- ward several tracks. If the last track in a folder on the USB device is skipped, the first track of the next folder is played. Random and repeat play mode: While files on a USB device are playing, the play pattern can [...]

While connected to the vehicle, the iPod® can only be operated by the vehicle audio controls. T o disconnect the iPod® from the vehicle, re- move the USB end of the cable from the USB jack on the vehicle, then remove the cable from the iPod®. * iPod® is a trademark of Apple Inc., registered in the U.S. and other countries. Compatibility The fol[...]

● Songs ● Podcasts ● Genres ● Composers ● Audiobooks ● Shuffle songs For more information about each item, see the iP od® Owner’s Manual. SEEK/CA T buttons: Press the SEEK/CA T buttons or to skip backward or forward one track. Press and hold the SEEK/CA T buttons or for 1.5 seconds while a track is playing to reverse or fast forward [...]

Connecting iPod® CAUTION ● Do not force the iPod® cable into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the iPod® cable and the port. Make sure that the iPod® cable is con- nected correctly into the USB port. (Some iPod® cables come with a mark as a guide. Make sure that the mark is facing the corr[...]

Audio main operation Place the ignition switch in the ACC or ON position. Press the AUX button repeatedly to switch to the iPod® mode. If the system has been turned off while the iPod® was playing, pressing the VOL/ON·OFF control knob will start the iP od®. AUX button: When the AUX button is pressed with the system off and the iPod® connected,[...]

Repeat : T ouch the “Repeat” key to apply a repeat play pattern to the iPod®. When the repeat mode is active, the icon is displayed to the left of the song title or album name to denote which repeat pattern is applied. T o cancel Repeat mode, touch the “Repeat” key until no icon is displayed. Seek buttons: Press the seek button or to skip [...]

4. When prompted for a Passkey code, enter “1234” from the handset. The Passkey code “1234” has been assigned by NISSAN and cannot be changed. Audio main operation T o switch to the Bluetooth® audio mode, press the AUX button repeatedly until the Bluetooth® audio mode is displayed on the screen. Use the vehicle audio controls or the Bluet[...]

Audio main operation T o switch to the Bluetooth® audio mode, press the CD•AUX button repeatedly until the Bluetooth® audio mode is displayed on the screen. The controls for the Bluetooth® audio are dis- played on the screen. Use the Preset 3 button for play and the Preset 4 button for pause. BLUET OO TH® STREAMING AUDIO WITH NA VIGA TION S Y[...]

3. Select the “Phone & Bluetooth” key. 4. Select the “Connect New Device” key. 5. The system acknowledges the command and asks you to initiate connecting from the phone handset. The connecting procedure of the cellular phone varies according to each cellular phone model. See the cellular phone Owner’s Manual for details. Y ou can also[...]

Compatibility The following iPhone® models are compatible with the system: ● iPhone® 3GS ● iPhone® 4 ● iPhone® 4S The latest Pandora® application should be in- stalled on the phone. Audio main operation Models without Navigation System: T o switch to the Pandora® audio mode, press the CD-AUX button repeatedly until the Pan- dora® audio[...]

The controls for the Pandora® audio are dis- played on the screen. T ouch the keys on the screen to play or pause the audio. T ouch the key to select “thumbs up” or the key to select “thumbs down”. NO TE: There is a limit of six skips per station per hour. If a “ ” (thumbs down) is given after the skip limit has been reached, the curre[...]

● A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated. 1. Source select and power on switch 2. Menu control switch/ENTER button 3. (Back) switch 4. Volume control switch STEERING WHEEL SWIT CH FOR AUDIO CONTROL POWER on switch With the ig[...]

AM and FM: ● Tilt up/down for less than 1.5 seconds to increase or decrease the preset station. ● Tilt up/down for more than 1.5 seconds to seek up or down to the next station. ● Press the ENTER button to show the list of preset stations. XM (if so equipped) : ● Tilt up/down for less than 1.5 seconds to increase or decrease the preset stati[...]

When installing a CB, ham radio or car phone in your vehicle, be sure to observe the following precautions; otherwise, the new equipment may adversely affect the engine control system and other electronic parts. WARNING ● A cellular phone should not be used for any purpose while driving so full atten- tion may be given to vehicle operation. Some [...]

Y our NISSAN is equipped with the Bluetooth® Hands-Free Phone System. If you have a com- patible Bluetooth® enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module. With Bluetooth® wireless technology , you can make or receive a hands-free telephone call with your cellular phone [...]

● Y ou will not be able to use a hands-free phone under the following conditions: – Y our vehicle is outside of the cellular ser- vice area. – Y our vehicle is in an area where it is difficult to receive a cellular signal; such as in a tunnel, in an underground parking garage, near a tall building or in a moun- tainous area. – Y our cellula[...]

Initialization When the ignition switch is placed in the ON position, NISSAN V oice Recognition is initialized, which takes a few seconds. If the button is pressed before the initialization completes, the system will announce “Hands-free phone system not ready” and will not react to voice commands. Operating tips T o get the best performance ou[...]

● Either “zero” or “oh” can be used for “0”. Example: 1-800-662-6200 – “One eight oh oh six six two six two oh oh” , or – “One eight zero zero six six two six two oh oh” ● Words can be used for the first 4 digits places only. Example: 1-800-662-6200 – “One eight hundred six six two six two oh oh” , – NO T “One [...]

Y ou can also use the button to interrupt the system feedback and give a command at once. See “List of voice commands” and “During a call” in this section for more information. PHONE/END While the V oice Recognition sys- tem is active, press and hold the button for 5 seconds to quit the V oice Recognition system at any time. ENTER button / [...]

1. Press the button on the steering wheel. The system announces the available commands. 2. Say: “Connect phone” 䊊 A . The system ac- knowledges the command and announces the next set of available commands. 3. Say: “ Add phone” 䊊 B . The system acknowl- edges the command and asks you to initiate connecting from the phone handset 䊊 C . [...]

LIST OF VOICE COMMANDS Main Menu “Call” “Phonebook” “Recent Calls” “Connect Phone” “Help” When you press and release the button on the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these commands and the com- mands in each sub-menu. Remember to wait for the tone before speaking. [...]

If a call back number does not exist, the system announces, “There is no number to call back” and ends the VR session. During a call During a call there are several command options available. Press the button on the steering wheel to mute the receiving voice and enter com- mands. ● “Help” — The system announces the avail- able commands.[...]

“T ransfer Entry” 䊊 A Use the T ransfer Entry command to store a new name in the system. When prompted by the system, say the name you would like to give the new entry . For example, say: “Mary .” If the name is too long or too short, the system tells you, then prompts you for a name again. Also, if the name sounds too much like a name al[...]

NO TE: Each phone has its own separate phone- book. Y ou cannot access Phone A ’s phone- book if you are currently connected with Phone B . “List Names” 䊊 A Use the List Names command to hear all the names and locations in the phone book. The system recites the phone book entries but does not include the actual phone numbers. When the playb[...]

“Select Phone” 䊊 B Use the Select Phone command to select from a list of phones connected to the vehicle. The sys- tem will list the names assigned to each phone and then prompt you for the phone you wish to select. Only one phone can be active at a time. “Delete Phone” 䊊 C Use the Delete Phone command to delete a phone that is connecte[...]

7. When preparation is complete and you are ready to begin, press the button. 8. The VA mode will be explained. Follow the instructions provided by the system. 9. When training is finished, the system will tell you an adequate number of phrases have been recorded. 10. The system will announce that voice adap- tation has been completed and the syste[...]

MANUAL CONTROL While using the V oice Recognition system, it is possible to select menu options by using the steering wheel controls instead of speaking voice commands. The manual control mode does not allow dialing a phone number by digits. The user may select an entry from the Phonebook or Re- cent Calls lists. T o re-activate voice recognition, [...]

TROUBLESHOO TING GUIDE The system should respond correctly to all voice commands without difficulty . If problems are en- countered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved. Symptom Solution System fails to interpret the command correctly[...]

WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. ● If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop you[...]

phone module when the ignition switch is placed in the ON position with the previously connected cellular phone turned on and carried in the ve- hicle. NO TE: Some devices require the user to accept connections to other Bluetooth® devices. If your phone does not connect automatic ally to the system, consult the phone’s Owner’s Manual for detai[...]

IC Regulatory information – Operation is subject to the following two con- ditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. – This Class B digital apparatus meets all re- quirements of the Canadian Interference- Causi[...]

● Y ou can cancel a command when the sys- tem is waiting for a response by saying, “Cancel” or “Quit.” The system announces “Cancel” and ends the VR session. Y ou can also press and hold the button on the steering wheel for 5 seconds at any time to end the VR session. Whenever the VR ses- sion is cancelled, a double beep is played to [...]

CONNECTING PROCEDURE NO TE: The connecting procedure must be per- formed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. T o connect a phone to the Bluetooth® Hands- Free Phone System: 1. Press the SETTING button. 2. Use the TUNE/SCROLL knob to select “Bluetooth” and then pres[...]

VOICE COMMANDS V oice commands can be used to operate the Bluetooth® Hands-Free Phone System. Press the button and say “Phone” to bring up the phone command menu. The available options are: ● Call ● Phonebook ● Recent Calls ● Send T ext ● Read T ext ● Select Phone “Call” For more information on the “Call” command, see “Ma[...]

● Missed Calls Speak this command to list the last five missed calls to the vehicle. If the call is from an entry in the phonebook, the name will be displayed. Otherwise, the phone number of the missed call will be displayed. Say “Dial” to call the number or “Send T ext” to send a text message to that number. Say “Next Entry” or “Pr[...]

RECEIVING A CALL When a call is received by the phone connected to the vehicle’s Bluetooth® Hands-Free Phone System, the call information is displayed on either the vehicle information display or both the vehicle information display and he control panel display . Press the button to accept the call. Press the button to reject the call. DURING A [...]

ENDING A CALL T o end an active call, press the button. TEXT MESSAGING WARNING ● Use the text messaging feature after stopping your vehicle in a safe location. If you have to use the feature while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. ● If you are unable to devote full attention to v[...]

T o send one of the custom messages, say “Custom Message”. If more than one cus- tom message is stored, the system will prompt for the number of the desired cus- tom message. For more information on set- ting and managing custom text messages, see “Bluetooth® settings” in this section. Reading a received text message: 1. Press the button. [...]

BLUET OO TH® SETTINGS T o access and adjust the settings for the Bluetooth® Hands-Free Phone System: 1. Press the SETTING button. 2. Use the TUNE/SCROLL knob to select “Bluetooth” and then press the ENTER but- ton: ● Bluetooth Select “On” or “Off” to turn the vehicle’s Bluetooth® system on or off. ● Add Phone or Device T o conn[...]

● New T ext Sound Select to adjust the volume of the sound that plays when a new text is received by a phone connected to the Bluetooth® Hands-Free Phone System. The setting all the way to the left indicates that the new text sound will be muted. ● Show Incoming T ext Select “Driver Only” to have incoming text messages displayed only in th[...]

Y our NISSAN is equipped with the Bluetooth® Hands-Free Phone System. If you have a com- patible Bluetooth® enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module. With Bluetooth® wireless technology , you can make or receive a hands-free telephone call with your cellular phone [...]

– Y our vehicle is in an area where it is difficult to receive cellular signal; such as in a tunnel, in an underground parking garage, near a tall building or in a moun- tainous area. – Y our cellular phone is locked to prevent it from being dialed. ● When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult[...]

CONNECTING PROCEDURE NO TE: The connecting procedure must be per- formed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. 1. Press the MENU button on the control panel. 2. Select the “Settings” key. 3. Select the “Phone & Bluetooth” key. LHA2253 LHA2248 4-102 Monitor, cl[...]

4. Select the “Connect New Device” key. 5. Initiate the connecting process from the handset. The system will display the mes- sage: “Is PIN XXXXXX displayed on your Bluetooth device?”. If the PIN is displayed on your Bluetooth® device, select “Y es” to complete the connecting process. For more information, see the Bluetooth® de- vice?[...]

MAKING A CALL T o make a call, follow the procedure below: 1. Press the button on the instrument panel. The “Phone” screen will appear on the display . 2. Select one of the following options to make a call: ● “Phonebook”: Select the name from an entry stored in the vehicle phonebook. ● “Call Lists”: Select the name from the in- comi[...]

DURING A CALL While a call is active, the following options are available on the screen: ● “Handset” Select this option to switch control of the phone call over to the handset. ● “Mute Mic.” Select this option to mute the microphone. Select again to unmute the microphone. ● Red phone ( ) icon Select to end the phone call. ENDING A CAL[...]

The system allows for the sending and receiving of text messages through the vehicle interface. Sending a text message: 1. Press the button. 2. Say “Send T ext”. 3. The system will provide a list of available commands in order to determine the recipi- ent of the text message. Choose from the following: ● (a name) ● Number ● Incoming Calls[...]

● Call Back Speak this command to call the sender of the text message using the Bluetooth® Hands-Free Phone System. ● Send T ext Speak this command to send a text message response to the sender of the text message. ● Read T ext Speak this command to read the text mes- sage again. ● Previous T ext Speak this command to move to the previ- ou[...]

● Phone Settings See “Phone settings” in this section for more information. ● Connect New Device Select to connect a new Bluetooth® device to the Bluetooth® Hands-Free Phone Sys- tem. ● Select Connected Device Select to choose a Bluetooth® device from a list of those devices connected to the Bluetooth® Hands-Free Phone System. ● Rep[...]

● Use Phonebook From: Select “Handset” to use the phone’s phone- book. Select “SIM” to use the phonebook on the SIM card. Select “Both” to use both sources. ● Download Phonebook Now Select to download the phonebook to the vehicle from the chosen source. ● Phone Notifications for Select “Driver” to have phone notifications sh[...]

Giving voice commands 1. Press the button. 2. The system announces: “Please say a com- mand.” A list of available commands is spo- ken by the system. 3. After the tone sounds and the face icon on the display changes, speak a command. Available commands are discussed later in this section. 4. Voice and display feedback are provided when the comm[...]

● W ait until a tone sounds before speaking a command. Otherwise, the command will not be received properly . ● Start speaking a command within 3.5 sec- onds after the tone sounds. ● Speak in a natural voice without pausing between words. S Y STEM FEA TURES NISSAN V oice Recognition can activate the fol- lowing systems: ● Bluetooth Hands-Fr[...]

BLUET OO TH® HANDS-FREE PHONE S Y STEM VOICE COMMANDS T o access the Bluetooth® Hands-Free Phone System voice commands: 1. Press the button. 2. Say “Call” and then a name in the vehicle phonebook to call that entry. Otherwise, say “Phone” to access various phone commands. If the Bluetooth® has been set to “Off”, the system announces:[...]

For more information about these commands, see the separate Navigation System Owner’s Manual. AUDIO S Y STEM VOICE COMMANDS T o access the audio system voice commands: 1. Press the button. 2. Say “ Audio” 3. Speak a command from the following avail- able commands: ● FM Switches the audio system to the FM mode. ● AM Switches the audio syst[...]

INFORMA TION VOICE COMMANDS The following voice commands are available for the information functions of the Navigation Sys- tem: ● T raffic ● Current Weather ● Weather Forecast ● Google™ Send-T o-Car ● POIs Powered by Google™ For more information about these commands, see the separate Navigation System Owner’s Manual. HELP VOICE COM[...]

TROUBLESHOO TING GUIDE The system should respond correctly to all voice commands without difficulty . If problems are en- countered, follow the solutions given in this guide for the appropriate error. Where the solutions are listed by number, try each solution in turn, starting with number one, until the problem is resolved. Symptom/error message S[...]

5 Starting and driving Precautions when starting and driving ................5 - 2 Exhaust gas (carbon monoxide) ..................5 - 2 Three-way catalyst ..............................5 - 2 Tire Pressure Monitoring System (TPMS) ..........5 - 3 Avoiding collision and rollover ....................5 - 6 Off-road recovery ...........................[...]

Special winter equipment ....................... 5-36 Driving on snow or ice ......................... 5-36 Engine block heater (if so equipped) ............. 5-36[...]

WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to ca[...]

● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously re- duce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunc- tions in th[...]

● The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving) . ● The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted on all 4 tires. After all 4 tires are inflat[...]

● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. ● Replacing ti[...]

Operation: 1. Add air to the tire. 2. After a few seconds, the hazard indicators will start flashing. 3. When the designated pressure is reached, the horn beeps once and the hazard indica- tors stop flashing. 4. Perform the above steps for each tire. ● If the tire is over-inflated more than ap- proximately 4 psi (30 kPa) , the horn beeps and the [...]

2. Do not apply the brakes. 3. Maintain a firm grip on the steering wheel with both hands and try to hold a straight course. 4. When appropriate, slowly release the accel- erator pedal to gradually slow the vehicle. 5. If there is nothing in the way , steer the ve- hicle to follow the road while vehicle speed is reduced. Do not attempt to drive the[...]

DRINKING AL COHOL/DRUGS AND DRIVING WARNING Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream re- duces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an [...]

The ignition lock is designed so that the ignition switch position cannot be switched to OFF until the shift selector is moved to the P (Park) posi- tion. When the ignition switch cannot be pushed to- ward the OFF position, proceed as follows: 1. Move the shift selector into the P (Park) position. 2. Push the ignition switch. The ignition switch po[...]

OFF: The ignition switch is in the OFF position when the engine is turned off using the ignition switch. No lights will illuminate on the ignition switch. ACC (Accessories) : This position activates electrical accessories, such as the radio, when the engine is not running. ACC has a battery saver feature that will turn the ignition switch to the OF[...]

3. T ouch the ignition switch with the Intelligent K ey as illustrated. (A chime will sound.) After step 3 is performed, when the ignition switch is pushed without depressing the brake pedal, the ignition switch position will change to ACC. 4. Push the ignition switch while depressing the brake pedal within 10 seconds after the chime sounds. The en[...]

1. Apply the parking brake. 2. Move the shift selector to P (Park) or N (Neutral) . P (Park) is recommended. The starter is designed not to operate if the shift selector is in any of the driving positions. 3. Push the ignition switch to the ON position. Depress the brake pedal and push the igni- tion switch to start the engine. T o start the engine[...]

CONTINUOUSL Y V ARIABLE TRANSMISSION (CVT) WARNING ● Do not depress the accelerator pedal while shifting from P (Park) or N (Neu- tral) to R (Reverse) , D (Drive) , Ds (Drive Sport) or manual shift mode (if so equipped) . Always depress the brake pedal until shifting is completed. Fail- ure to do so could cause you to lose control and have an acc[...]

NO TE: Engine power may be automatically re- duced to protect the CVT if the engine speed increases quickly when driving on slippery roads or while being tested on some dynamometers. Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before moving the shift selector out of the P (Park) position. 2. Keep the foot b[...]

R (Reverse) : CAUTION T o prevent transmission damage, use the P (Park) or R (Reverse) position only when the vehicle is completely stopped. Use the R (Reverse) position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed to move the shift selector from P (Park) , N (N[...]

When canceling the manual shift mode, return the selector lever to the D (Drive) position. The transmission returns to the normal driving mode. When you pull the paddle shifter (if so equipped) while in the D (Drive) position, the transmission will shift to the upper or lower range temporarily. The transmission will automatically return to the D (D[...]

Shift lock release If the battery charge is low or discharged, the shift selector may not be moved from the P (Park) position even with the brake pedal depressed and the shift selector button pushed. It will be necessary to jump start or have your battery charged, see “Jump starting” in the “In case of emergency” section. Contact your NISSA[...]

Each time the engine is started, or when the shift selector is shifted to any position other than D (Drive) , the Overdrive off mode will be automati- cally turned off. Accelerator downshift — in D position — For passing or hill climbing, depress the accel- erator pedal to the floor. This shifts the transmis- sion down into a lower gear, depend[...]

WARNING ● Be sure the parking brake is fully re- leased before driving. Failure to do so can cause brake failure and lead to an accident. ● Do not release the parking brake from outside the vehicle. ● Do not use the shift selector in place of the parking brake. When parking, be sure the parking brake is fully engaged. ● Do not leave childre[...]

● The LDW system is only a warning de- vice to help inform the driver of a poten- tial unintended lane departure. It will not steer the vehicle or prevent loss of control. It is the driver’s responsibility to stay alert, drive safely, keep the ve- hicle in the traveling lane, and be in control of the vehicle at all times. ● The camera unit ma[...]

Detection zone The camera unit can detect vehicles on either side of your vehicle when part of another vehicle is within the detection zone shown as illustrated. This detection zone typically starts from the out- side mirror of your vehicle and extends approxi- mately 10 ft (3.0 m) behind the rear bumper, and approximately 10 ft (3.0 m) sideways. N[...]

– Oncoming vehicles – A vehicle approaching rapidly from behind. (See “BSW driving situa- tions” later in this section) – A vehicle which your vehicle over- takes rapidly. (See “BSW driving situations” later in this section) – A vehicle that merges or changes lanes rapidly directly next to your vehicle. ● The camera unit may not b[...]

If the driver activates the turn signal, then the Blind Spot indicator light flashes and a chime will sound twice. NO TE: If the driver activates the turn signal before a vehicle enters the detection zone, the Blind Spot indicator light will flash but no chime will sound when the other vehicle is detected. Overtaking other vehicles The Blind Spot i[...]

LDW S Y STEM OPERA TION The LDW system operates above approximately 45 MPH (70 km/h). When the vehicle approaches either the left or the right of the traveling lane, the LDW system will chime a sound and the LDW light (orange) on the instrument panel will blink to alert the driver The LDW system is not designed to operate under the following condit[...]

WARNING ● The camera unit may not be able to detect properly under the following conditions: – On roads where there are multiple parallel lane markers; lane markers that are faded or not painted clearly; yellow painted lane markers; non- standard lane markers; or lane mark - ers covered with water, dirt, snow, etc . – On roads where the disco[...]

CAMERA UNIT MAINTENANCE The rear camera unit 䊊 1 for the LDW/BSW sys- tems is located above the rear licence plate. T o maintain the proper operation of the LDW/BSW systems and help keep the system functioning, be sure to observe the following: ● Always keep the camera unit clean. ● Do not attach “licence plate accessories” that reflect l[...]

T o set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. T ake your foot off the accelerator pedal. Y our vehicle maintains the set speed. ● T o pass another vehicle, depress the ac- celerator pedal. When you release the pedal, the vehicle returns to the previously set speed. ● The vehicle m[...]

CAUTION During the first 1,200 miles (2,000 km), follow these recommendations to obtain maximum engine performance and en- sure the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in short- ened engine life and reduced engine performance. ● Avoid driving for long periods at constant speed, ei[...]

6. Plan for the Shortest Route ● Utilize a map or navigation system to de- termine the best route to save time 7. Avoid Idling ● Shutting off your engine when safe for stops exceeding 30–60 seconds saves fuel and reduces emissions 8. Buy an Automated Pass for T oll Roads ● Automated passes permit drivers to use special lanes to maintain cru[...]

WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. ● Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) . Fail- ure to do so could cause the vehicle to move unexpectedly or roll away and re- sult in[...]

WARNING ● If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be harder to operate. ● When the power steering warning light illuminates with the engine running, there will be no power assist for the steering. Y ou will still have control of the vehicle, but the steering wil[...]

WARNING ● While driving on a slippery surface, be careful when braking, accelerating or downshifting. Abrupt braking or accel- erating could cause the wheels to skid and result in an accident. ● If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder. W et brakes When th[...]

WARNING Do not pump the brake pedal. Doing so may result in increased stopping distances. Self-test feature The ABS includes electronic sensors, electric pumps, hydraulic solenoids and a computer. The computer has a built-in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or rev[...]

When the VDC system operates, the indi- cator in the instrument panel flashes so note the following: ● The road may be slippery or the system may determine some action is required to help keep the vehicle on the steered path. ● Y ou may feel a pulsation in the brake pedal and hear a noise or vibration from under the hood. This is normal and ind[...]

● When driving on an unstable surface such as a turntable, ferry, elevator or ramp, the indicator may flash or the indicator light may illuminate. This is not a malfunction. Restart the engine after driving onto a stable surface. ● If wheels or tires other than the NISSAN recommended ones are used, the VDC system may not operate properly and th[...]

3. Tire chains may be used. For details see “Tire chains” in the “Maintenance and do-it- yourself” section of this manual. SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter: ● A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades. ● A sturdy,[...]

T o use the engine block heater: 1. T urn the engine off. 2. Open the hood and unwrap the engine block heater cord. 3. Plug the engine block heater cord into a grounded 3-wire, 3-pronged extension cord. 4. Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110- volt AC (V AC) outlet. 5. The engine block heater must be p[...]

MEMO 5-38 Starting and driving[...]

6 In case of emergency Emergency engine shut off .........................6 - 2 Hazard warning flasher switch ......................6 - 2 Flat tire ...........................................6 - 3 Tire Pressure Monitoring System (TPMS) ..........6 - 3 Changing a flat tire .............................6 - 3 Jump starting ............................[...]

T o shut off the engine in an emergency situation while driving, perform the following procedure: – Rapidly push the push-button ignition switch 3 consecutive times in less than 1.5 seconds, or – Push and hold the push-button ignition switch for more than 2 seconds. Push the switch on to warn other drivers when you must stop or park under emerg[...]

TIRE PRESSURE MONIT ORING S Y STEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, and the “Tire Pressure Low - Add Air” warning appears in the vehicle information display, one or more of your tires is si[...]

4. T urn off the engine. 5. Raise the hood to warn other traffic and to signal professional road assistance person- nel that you need assistance. 6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle. WARNING ● Make sure the parking brake is securely applied and the CVT is shifted into[...]

T urn the clamp to remove the spare tire. Remove the spare tire. Removing wheel cover (if so equipped) CAUTION Do not use your hands to pry off wheel caps or wheel covers. Doing so could re- sult in personal injury. T o remove the wheel cover, use the jack rod 䊊 1 as illustrated. Apply cloth 䊊 2 between the wheel and jack rod to prevent damagin[...]

● Use the correct jack -up points. Never use any other part of the vehicle for jack support. ● Never jack up the vehicle more than necessary. ● Never use blocks on or under the jack. ● Do not start or run the engine while vehicle is on the jack. It may cause the vehicle to move. This is especially true for vehicles with limited slip differe[...]

Installing the spare tire The spare tire is designed for emergency use. See specific instructions under the heading “ Wheels and tires” in the “Mainte- nance and do-it-yourself” section of this manual. 1. Clean any mud or dirt from the surface be- tween the wheel and hub. 2. Carefully put the spare tire on and tighten the wheel nuts finger [...]

T o start your engine with a booster battery , the instructions and precautions below must be fol- lowed. WARNING ● If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle. ● Explosive hydrogen gas is always pres- ent in the vicinity of the battery. Keep all spar[...]

WARNING Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury. 1. If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries near each other. Do not allow the two vehicles to touch. 2. Apply the parking brake. Move the shift se- lector t[...]

CAUTION ● Do not push start this vehicle. The three-way catalyst may be damaged. ● Continuously Variable T ransmission (CVT) models cannot be push-started or tow-started. Attempting to do so may cause transmission damage. If your vehicle is overheating (indicated by an extremely high temperature gauge reading) , or if you feel a lack of engine [...]

6. After the engine cools down, check the cool- ant level in the engine coolant reservoir tank with the engine running. Add coolant to the engine coolant reservoir tank if necessary. Have your vehicle repaired at a NISSAN dealer. When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect [...]

T OWING RECOMMENDED B Y NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as illustrated. CAUTION ● Never tow Continuously V ariable T rans- mission (CVT) models with the front wheels on the ground or four wheels on the ground (forward or backward) , as this[...]

VEHICLE RECOVERY (freeing a stuck vehicle) Pulling a stuck vehicle WARNING T o avoid vehicle damage, serious per- sonal injury or death when recovering a stuck vehicle: ● Contact a professional towing service to recover the vehicle if you have any questions regarding the recovery procedure. ● Do not use the vehicle tie-downs to tow or free a st[...]

MEMO 6-14 In case of emergency[...]

7 Appearance and care Cleaning exterior ..................................7 - 2 W ashing ......................................7 - 2 W axing ........................................7 - 2 Removing spots ................................7 - 3 Underbody ....................................7 - 3 Glass .........................................7 - 3 Alumi[...]

In order to maintain the appearance of your ve- hicle, it is important to take proper care of it. T o protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads. ● when contaminants such as soot, bird drop- pings, tree sap, metal parti[...]

REMOVING SPO TS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store. UNDERBOD Y In areas where road salt is used in winter, it is necessary to clean the u[...]

● Do not apply wheel cleaners to the wheels when they are hot. The wheel temperature should be the same as am- bient temperature. ● Rinse the wheel to completely remove the cleaner within 15 minutes after the cleaner is applied. CHROME P ARTS Clean all chrome parts regularly with a non- abrasive chrome polish to maintain the finish. TIRE DRESSI[...]

● Never use fabric protectors unless rec- ommended by the manufacturer. ● Do not use glass or plastic cleaner on meter or gauge lens covers. It may dam- age the lens cover. AIR FRESHENERS Most air fresheners use a solvent that could affect the vehicle interior. If you use an air freshener, take the following precautions: ● Hanging-type air fr[...]

SEA T BEL TS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemen- tal restraint system” section of this manual. WARNING Do not allow wet seat belts to roll [...]

CAUTION ● NEVER remove dirt, sand or other de- bris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. ● Never allow water or other liquids to come in contact with electronic compo- nents inside the vehicle as this may damage them. Chemicals used for road surface de-icing are extremely corr[...]

8 Maintenance and do-it-yourself Maintenance requirements ..........................8 - 2 General maintenance ..............................8 - 2 Explanation of general maintenance items .........8 - 2 Maintenance precautions ...........................8 - 5 Engine compartment check locations ................8 - 6 Engine cooling system ............[...]

T ypes of tires .................................. 8-42 Tire chains .................................... 8-43 Changing wheels and tires ..................... 8-44[...]

Y our NISSAN has been designed to have mini- mum maintenance requirements with long ser- vice intervals to save you both time and money . However, some day-to-day and regular mainte- nance is essential to maintain your NISSAN’s good mechanical condition, as well as its emis- sions and engine performance. It is the owner’s responsibility to make[...]

When driving in areas using road salt or other corrosive materials, check lubrication frequently . Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely . Also check headlight aim. Road wheel nuts (lug nuts)* Wh[...]

Seat belts Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely. Check the belt web- bing for cuts, fraying, wear or damage. Steering wheel Check for changes in the steer- ing system, such as excessive freeplay, hard steering or strange noise[...]

When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precau- tions which should be closely observed. WARNING ● Park the vehicle on a level surface, ap- ply the parking brake securely and block the wheels to prevent [...]

QR25DE engine 1. P ower steering fluid reservoir 2. Engine coolant reservoir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Air cleaner 6. Fuse block/ Fusible links 7. Battery 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Windshield-washer fluid reservoir LDI2111 ENGINE COMP ARTMENT CHECK LOCA TIONS 8-6 Maintenance and do[...]

VQ35DE engine 1. P ower steering fluid reservoir 2. Engine coolant reservoir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Air cleaner 6. Fuse block/ Fusible links 7. Battery 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Windshield-washer fluid reservoir LDI2112 Maintenance and do-it-yourself 8-7[...]

The engine cooling system is filled at the factory with a pre-diluted mixture of 50% Genuine NISSAN Engine Coolant (blue) and 50% water to provide year-round anti-freeze and coolant protection. The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cool- ing system additives are not necessary. WARNING ● Never remove th[...]

CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir when the engine is cold. If the coolant level is below the MIN level 䊊 B , add coolant to the MAX level 䊊 A . If the reservoir is empty , check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with[...]

CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply the parking brake. 2. Start the engine and let it idle until it reaches operating temperature. 3. T urn off the engine. Wait more than 10 minutes for the oil to drain back into the oil pan. 4. Remove the dipstick and wipe it clean. Re- insert it all the way . 5. Remove the d[...]

CAUTION ● Oil level should be checked regularly. Operating the engine with an insuffi- cient amount of oil can damage the engine, and such damage is not cov- ered by warranty. ● It is normal to add some oil between oil maintenance intervals or during the break -in period, depending on the se- verity of operating conditions. CHANGING ENGINE OIL [...]

WARNING ● Prolonged and repeated contact with used engine oil may cause skin cancer. ● T ry to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. ● Keep used engine oil out of reach of children. CAUTION Be careful not to burn yourself. The engine oil may be hot. 6. [...]

CAUTION Be careful not to burn yourself. The engine oil may be hot. 5. Wipe the engine oil filter sealing surface with a clean rag. CAUTION Be sure to remove any old gasket material remaining on the sealing surface of the engine. Failure to do so could lead to engine damage. 6. Coat the gasket on the new filter with clean engine oil. 7. Screw on th[...]

Check the fluid level in the reservoir. The fluid level should be checked when the fluid is cold at fluid temperatures of 0 to 30ºC (32 to 86ºF) . The fluid level can be checked with the level gauge which is attached to the cap. T o check the fluid level, remove the cap. The fluid level should be between the MAX 䊊 1 and MIN 䊊 2 lines. If the [...]

BRAKE FLUID Check the brake fluid level in the reservoir. If the fluid level is below the MIN line or the brake warning light comes on, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added frequently , the system should be checked by a NISSAN dealer. WINDSHIELD-W ASHER FLUID RESERVOIR [...]

● Pre-mix washer fluid concentrates with water to the manufacturer’s recom- mended levels before pouring the fluid into the windshield-washer fluid reser- voir. Do not use the windshield-washer fluid reservoir to mix the washer fluid concentrate and water. ● Keep the battery surface clean and dry. Clean the battery with a solution of baking s[...]

● Keep battery out of the reach of children. ● Do not tip the battery. Keep the vent caps tight and the battery level. 1. Remove the vent caps with a screwdriver as shown. Use a cloth to protect the battery case. 2. Check the fluid level in each cell. If it is necessary to add fluid, add only distilled water to bring the level up to the bottom [...]

V ehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP ST ARTING If jump starting is necessary , see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN d[...]

1. Crankshaft pulley 2. Drive belt Automatic tensioner 3. W ater pump pulley 4. Alternator 5. Air conditioner WARNING Be sure the ignition switch is placed in the OFF or LOCK position before servicing drive belt. The engine could rotate unexpectedly. 1. Visually inspect the belt for signs of unusual wear, cuts, fraying or looseness. If the belt is [...]

REPLACING SP ARK PLUGS Iridium-tipped spark plugs It is not necessary to replace iridium-tipped 䊊 A spark plugs as frequently as conventional type spark plugs because they last much longer. Fol- low the maintenance log shown in the “NISSAN Service and Maintenance Guide”. Do not service iridium-tipped spark plugs by cleaning or regap- ping. ?[...]

● Wipe the inside of the air cleaner filter hous- ing and the cover with a damp cloth. NO TE: After installing a new air cleaner, make sure the air cleaner cover is seated in the housing and latch the clips. WARNING ● Operating the engine with the air cleaner removed can cause you or oth- ers to be burned. The air cleaner not only cleans the ai[...]

REPLACING Replace the wiper blades if they are worn. 1. Lift the wiper arm away from the windshield. 䊊 2 Push the release tab, then move the wiper blade down the wiper arm to remove. 䊊 3 Remove the wiper blade. 4. Insert the new wiper blade onto the wiper arm until it clicks into place. 5. Rotate the wiper blade so the dimple is in the groove. [...]

If the brakes do not operate properly , have the brakes checked by a NISSAN dealer. SELF-ADJUSTING BRAKES Y our vehicle is equipped with self-adjusting brakes. The front and rear disc-type brakes self-adjust every time the brake pedal is applied. WARNING See a NISSAN dealer for a brake system check if the brake pedal height does not return to norma[...]

If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration. This will not affect the performance of the fuse. Make sure the fuse is installed in the fuse box securely. T ype B fuses cannot be installed in the under- hood fuse boxes. Only use type A fuses in the underhood fu[...]

5. If the fuse is open 䊊 A , replace it with a new fuse 䊊 B . 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only Genuine NI[...]

4. If the fuse is open 䊊 A , replace it with an equivalent good fuse 䊊 B . 5. Push the fuse box cover to install. 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. Extended storage switch If any electrical equipment does not operate, remove the extended storage switch and check for an open fuse. NO[...]

How to replace the extended storage switch: 1. T o remove the extended storage switch, be sure the ignition switch is in the OFF or L OCK position. 2. Be sure the headlight switch is in the OFF position. 3. Remove the fuse box cover. 4. Pinch the locking tabs 䊊 1 found on each side of the storage switch. 5. Pull the storage switch straight out fr[...]

4. Close the lid securely as illustrated 䊊 C 䊊 D . 5. Operate the buttons to check the operation. See a NISSAN dealer if you need assistance for replacement. FCC Notice: For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2)[...]

CAUTION ● Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact a NISSAN dealer. ● Do not leave the headlight assembly open without a bulb installed for a long period of time. Dust, moisture, smoke, etc . entering the headlight body may affect bulb performance. Remove the bulb from the headlight assembly[...]

1. Disconnect the negative battery cable. 2. Remove the fasteners 䊊 A ; carefully pull back the front fender protector . 3. Rotate the bulb 䊊 B counterclockwise and pull out to remove. P ARK/TURN SIGNAL LIGHTS Replacing the park/turn signal bulb LDI2144 8-30 Maintenance and do-it-yourself[...]

1. Disconnect the negative battery cable. 2. Remove the fasteners 䊊 A ; carefully pull back the front fender protector. 3. Rotate the bulb 䊊 B counterclockwise and pull out to remove. LDI2137 Maintenance and do-it-yourself 8-31[...]

EXTERIOR AND INTERIOR LIGHTS Item W attage (W) Bulb No.* 1 Headlight assembly * 2 Low (Halogen) 55 H11 Low (Xenon) 35 D2S High 65 H9 Sidemarker 5 W5W Door mirror turn signal light * 2 —— Park/ Turn signal light 28/8 7444A Front fog light (if so equipped) 55 H11 Day time running lights (Canada only) 19 PS19W Step light 3.8 194 C HTEI Rear combin[...]

1. Front map light 2. Headlamp assembly 3. Park/ T urn signal light 4. Fog light (if so equipped)/ Day time run- ning light (Canada only) 5. Step light 6. Door mirror turn signal light 7. Personal light 8. High-mount stoplight (if so equipped) 9. T runk light 10. Spoiler-mount stop light 11. Rear combination light 12. License plate light LDI2100 Ma[...]

Replacement procedures All other lights are either type A , B, C or D. When replacing a bulb, first remove the lens, light and/or cover. Indicates bulb removal Indicates bulb installation Use a cloth 䊊 1 to protect the housing. Use a cloth 䊊 1 to protect the housing. Rear combination light Bulb replacement requires the removal of the rear combi[...]

If you have a flat tire, see “Flat tire” in the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit and the “Tir[...]

The “TPMS with Easy Fill Tire Alert” pro- vides visual and audible signals outside the vehicle for inflating tires to the recom- mended COLD tire pressure. For more information, see “TPMS with Easy Fill Tire Alert” in the “Starting and driving” section. Incorrect tire pressure, including un- der inflation, may adversely affect tire life[...]

Tire and loading information label 䊊 1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle. 䊊 2 Original tire size: The size of the tires originally installed on the vehicle at the factory . 䊊 3 Cold tire pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the[...]

Checking tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage. 3. Remove [...]

Size Cold Tire Inflation Pres- sure Front Original Tire P215/60R16 220 kPa, 32 PSI P215/55R17 230 kPa, 33 PSI P235/45R18 Rear Original Tire P215/60R16 220 kPa, 32 PSI P215/55R17 230 kPa, 33 PSI P235/45R18 Spare Tire T135/70D16 420 kPa, 60 PSI TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of [...]

䊊 1 Tire size (example: P215/65R15 95H) 1. P: The “P” indicates the tire is de- signed for passenger vehicles (not all tires have this information) . 2. Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to side- wall edge. 3. T wo-digit number (65): This number, known as the aspect ratio, gi[...]

䊊 2 TIN (Tire Identification Number) for a new tire (example: DO T XX XX XXX XXXX) 1. DO T : Abbreviation for the “Depart- ment Of T ransportation” . The symbol can be placed above, below or to the left or right of the Tire Identification Number. 2. T wo-digit code: Manufacturer’s identification mark. 3. T wo-digit code: Tire size. 4. Three[...]

䊊 7 The word “radial” The word “radial” is shown if the tire has radial structure. 䊊 8 Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related T erminology In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears whi[...]

For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS CAUTI[...]

Do not use tire chains on dry roads. Driving with tire chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress. CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km). See “Flat tire” in the “In case of emer- gency” section of this manual [...]

1. W ear indicator 2. Location mark Tire wear and damage WARNING ● Tires should be periodically in- spected for wear, cracking, bulg- ing or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced. ● The original tires have built-in tread wear indicators. When the wear indicators ar[...]

● If the wheels are changed for any rea- son, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade ve- hicle handling characteristics, affect the VDC system and/or interference with the brake disc s/drums. Such inter- ference can lead to decreased braking efficien[...]

Spare tire (TEMPORARY USE ONL Y spare tire) Observe the following precautions if the TEM- PORAR Y USE ONL Y spare tire must be used. Otherwise, your vehicle could be damaged or involved in an accident: WARNING ● The spare tire should be used for emer- gency use only. It should be replaced with the standard tire at the first oppor- tunity to avoid[...]

MEMO 8-48 Maintenance and do-it-yourself[...]

9 T echnical and consumer information Capacities and recommended fuel/lubricants .........9 - 2 Fuel recommendation ...........................9 - 3 Engine oil and oil filter recommendations ..........9 - 6 Air conditioner system refrigerant and oil recommendations ..............................9 - 7 Specifications .................................[...]

The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Capacity (Approximate) Recommended Fluids and Lubricants US measure Imp measure Liter Fuel 18 gal 15 gal 68.0 Se[...]

FUEL RECOMMENDA TION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91) . CAUTION ● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage. ● Under no circumstances should a leaded gasoline be[...]

● If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol) . It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicl[...]

QR25DE engine models LTI2037 T echnical and consumer information 9-5[...]

ENGINE OIL AND OIL FIL TER RECOMMENDA TIONS Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See “Capacities and recommended fuel/lubricants” earlier in this section. NISSAN recommends the use of an energy conserving oil in order to improv[...]

Y our engine was filled with a high-quality engine oil when it was built. Y ou do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: ● repeated short distance drivin[...]

ENGINE Model QR25DE VQ35DE T ype Gasoline, 4-cycle, DOHC Gasoline, 4-cycle, DOHC Cylinder arrangement 4-cylinder in-line 6-cylinder, V-block, Slanted at 60° Bore x Stroke in (mm) 3.5 x 3.9 (89.0 x 100.0) 3.760 x 3.205 (95.5 x 81.4) Displacement cu in (cm 3 ) 151.82 (2,488) 213.45 (3,498) Firing order 1–3–4–2 1–2–3–4–5–6 Idle speed [...]

WHEELS AND TIRES Wheel type Size Offset mm (in) Steel 16 x 7.0J 50 (1.97) Aluminum 17 x 7.5J 50 (1.97) Aluminum 18 x 7.5J 55 (2.17) T -type (ST spare) 16 x 4T 40 (1.57) T -type (AL spare) 16 x 4T 30 (1.18) Tire size 2.5 models P215/60R16 2.5 models and 3.5 models P215/55R17 3.5 models P235/45R18 Spare tire T135/70D16 DIMENSIONS AND WEIGHTS Overall [...]

When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where app[...]

ENGINE SERIAL NUMBER The number is stamped on the engine as shown. F .M.V .S.S./C.M.V .S.S. CERTIFICA TION LABEL The Federal/Canadian Motor V ehicle Safety Standard (F .M.V .S.S./C.M.V .S.S.) certification la- bel is affixed as shown. This label contains valu- able vehicle information, such as: Gross V ehicle W eight Ratings (GVWR) , Gross Axle W e[...]

EMISSION CONTROL INFORMA TION LABEL The emission control information label is at- tached to the underside of the hood as shown. TIRE AND L OADING INFORMA TION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. AIR CONDITIONER SPECIFICA TION LABEL The air conditioner specification label is[...]

T o mount the front license plate, attach the li- cense plate bracket 䊊 1 to the plastic finisher at the location marks (small dimples) using the two 6 mm screws provided. WARNING ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed[...]

● Vehicle Capacity Weight, Load limit, T otal load capacity - maximum total weight limit specified of the load (passengers and cargo) for the ve- hicle. This is the maximum combined weight of occupants and cargo that can be loaded into the vehicle. If the vehicle is used to tow a trailer, the trailer tongue weight must be in- cluded as part of th[...]

Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX [...]

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. Before driving a loaded vehicle, confirm that you do not exceed the Gross Vehicle W eight Rating (GVWR) or the Gross Axle W eight Rating (GA WR) for your vehicle. Se[...]

Do not tow a trailer with your vehicle. FLA T T OWING T owing your vehicle with all four wheels on the ground is sometimes called flat towing. This method is sometimes used when towing a vehicle behind a recreational vehicle, such as a motor home. CAUTION ● Failure to follow these guidelines can result in severe transmission damage. ● Whenever [...]

WARNING The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristic s. T emperature A , B and C The temperature grades are A (the highest) , B, and C, representing the tire’s resistance to the generation of heat, and its abi[...]

For USA If you believe that your vehicle has a de- fect which could cause a crash or could cause injury or death, you should immedi- ately inform the National Highway T raffic Safety Administration (NHTSA) in addi- tion to notifying NISSAN. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exis[...]

Due to legal requirements in some states and Canadian Provinces, your vehicle may be re- quired to be in what is called the “ready condi- tion” for an Inspection/Maintenance (I/M) test of the emission control system. The vehicle is set to the “ready condition” when it is driven through certain driving patterns. Usually, the ready condition [...]

Genuine NISSAN Service Manuals for this model year and prior can be purchased. A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle. This manual is the same one used by the factory- trained technicians working at NISSAN dealer- ships. Genuine NISSAN Owner’s Manuals can also be purchased. For USA Fo[...]

MEMO 9-22 T echnical and consumer information[...]

10 Index A ABS (Anti-lock Braking System) ........ 5 - 3 2 Air bag (See supplemental restraint system) . .1-37 Air bag system Front (See supplemental front impact air bag system) ............... 1 - 4 4 A i r b a g w a r n i n g l i g h t ........... 1 - 5 2 , 2 - 1 4 Air cleaner housing filter ............ 8 - 2 0 Air conditioner Air conditioner o[...]

Cold weather driving .............. 5 - 3 5 Compact disc (CD) player .... 4 - 4 3 , 4 - 4 8 , 4 - 5 4 Compass display ................. 2 - 6 Console box ................... 2 - 4 1 Console light ................... 2 - 4 7 Continuously V ariable T ransmission (CVT) . . .5-13 Continuously V ariable T ransmission (CVT) fluid .................. 8 - 1[...]

F u s i b l e l i n k s ................... 8 - 2 5 G Garage door opener, HomeLink® Universal T r a n s c e i v e r .................... 2 - 4 8 G a s c a p ..................... 3 - 3 0 Gauge Engine coolant temperature gauge ..... 2 - 5 Fuel gauge ................... 2 - 5 Odometer ................... 2 - 4 Speedometer ................. 2 - 4 T a[...]

I n t e r i o r l i g h t .................. 2 - 4 6 L i g h t b u l b s .................. 8 - 2 8 Low tire pressure warning light ....... 2 - 1 1 Low windshield-washer fluid warning l i g h t ...................... 2 - 2 4 Passenger air bag and status light ..... 1 - 4 6 Personal lights ................ 2 - 4 7 Security indicator light ..........[...]

R Radio Car phone or CB radio ........... 4 - 7 3 FM-AM radio with compact disc (CD) player .................. 4 - 4 1 FM/AM/SA T radio with compact disc (CD) player .............. 4 - 4 6 , 4 - 5 1 Readiness for inspection maintenance (I/M) test ..................... 9 - 2 0 Rear power windows .............. 2 - 4 3 R e a r s e a t ...............[...]

T T achometer .................... 2 - 4 T emperature gauge Engine coolant temperature gauge ..... 2 - 5 Theft (NISSAN vehicle immobilizer system) , engine start ............. 2 - 2 7 , 3 - 4 , 5 - 1 1 Three-way catalyst ................ 5 - 2 Tire Flat tire ..................... 6 - 3 Spare tire ................ 6 - 4 , 8 - 4 7 Tire and Loading In[...]

RECOMMENDED FUEL: Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91) . CAUTION ● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage. ● Under no circumstances should a leaded gasoline be us[...]

® 2013 AL TI MA S E D AN OWN E R’S MAN UAL For y our s afety , read car efully and keep in this v ehicle. 2013 N IS SAN AL TI MA SE DAN L33-D L33-D Printing : December 2012 (05) Publication No.: OM0E 0L32U2 Printed in U .S.A. OM3E 0L33U4[...]