Français dropdown-ico

Onkyo HT-R8230 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Onkyo HT-R8230. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Onkyo HT-R8230 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Onkyo HT-R8230 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Onkyo HT-R8230 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Onkyo HT-R8230
- nom du fabricant et année de fabrication Onkyo HT-R8230
- instructions d'utilisation, de réglage et d’entretien de l'équipement Onkyo HT-R8230
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Onkyo HT-R8230 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Onkyo HT-R8230 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Onkyo en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Onkyo HT-R8230, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Onkyo HT-R8230, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Onkyo HT-R8230. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Contents Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. HT-R8230 Appendix Tr[...]

  • Page 2

    2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near an y heat so[...]

  • Page 3

    3 Precautions For U.S. models Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of ca[...]

  • Page 4

    4 Features Amplifier Features •5 × 100 W/Channel @ 8 Ω , 20–20 kHz, 0.08% THD • WRAT-Wide Range Amplifier Technology • Optimum Gain Volume Circuitry • DTS, Dolby Digital, Dolby Pro Logic II • CinemaFILTER • Non-Scaling Configuration • A-Form–Auto Format Sensing • Linear PCM 96 kHz/24-bit D/A Converters • Advanced 24-bit DSP[...]

  • Page 5

    5 Bef ore Using the HT -R8230 30 ˚ 30 ˚ Approx. 16 feet (5m) Remote control sensor Standby indicator HT-R8230 2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. 3 Close the battery compartment. Notes • The supplied batteries should last for about six months, although this will var[...]

  • Page 6

    6 Front panel Inde x to par ts and contr ols For operational instructions, refer to the page indicated in brackets. 1 STANDBY/ON button [17] When STANDBY/ON button is pressed to ON, the display will light to show the current volume setting for about 5 seconds then show the current sound input source. Pressing the button again returns the HT-R8230 t[...]

  • Page 7

    7 ab c d e f g hi Display @ DISPLAY button [25] Each time you press the DISPLAY button, the display changes. # AUDIO SELECTOR button [26, 27] Press to select an audio input signal format other than FM and AM. Each time this button is pressed, the setting cycles. $ Input selector buttons (DVD, VIDEO 1, VIDEO 2, VIDEO 3, TAPE, TUNER, and CD) [17, 21-[...]

  • Page 8

    8 Index to parts and controls Rear panel For operational instructions, refer to the page indicated in brackets. 1 REMOTE CONTROL [16] Connect the Onkyo components that have connectors such as a CD player, and cassette tape deck using the cables provided with them. When these components are interconnected, they can be controlled from the remote cont[...]

  • Page 9

    9 Explanations on this page are for controlling the HT-R8230. To operate other components, see “Using the remote controller with your other AV components” on pages 33 through 34. For operational instructions, refer to the page indicated in brackets. 1 SLEEP button [25] For setting the sleep time. This button is provided only on the remote contr[...]

  • Page 10

    10 RL RL FRONT SPEAKERS A FRONT SPEAKERS B RL SURROUND SPEAKERS CENTER SPEAKER AC OUTLET ANTENNA FM 75 AM RL RL AUDIO OUT (PLA Y) AUDIO IN (REC) RL AUDIO OUT (PLA Y) DIGIT AL OUT OPTICAL VIDEO IN Connecting to audio/video equipment Audio connection cable (Analog signal) Optical fiber cable (Digital signal) Optical plug Signal flow Audio (R) Cassett[...]

  • Page 11

    11 RL RL FRONT SPEAKERS A FRONT SPEAKERS B RL SURROUND SPEAKERS CENTER SPEAKER AC OUTLET ANTENNA FM 75 AM DIGIT AL OUT VIDEO OUT AUDIO OUT VIDEO IN AUDIO IN RL R L L R L R VIDEO OUT AUDIO OUT VIDEO OUT AUDIO OUT L R VIDEO OUT FRONT CENTER SUBWOOFER SURR L R AUDIO OUT COAXIAL DVD player or component with 5.1 ch output (DVD)* 1 Video cassette player [...]

  • Page 12

    12 P ositioning speaker s/Connecting speaker s Two speaker systems can be connected to the Receiver. The speaker system A is to be placed in the main room, and the speaker system B is to be placed in a second room. The speaker system A consists of the FRONT SPEAKERS A (L/R), CENTER SPEAKER, SURROUND SPEAKERS (L/R) and SUBWOOFER. You can reproduce t[...]

  • Page 13

    13 Positioning speakers/Connecting speakers Before connecting • Refer also to the instruction manuals of the speakers. • Be sure to connect the positive and negative cables for the speakers properly. If they are mixed up, the left and right signals will be reversed and the audio will sound unnatural. • Connect speakers with an impedance betwe[...]

  • Page 14

    14 ANTENNA FM 75 AM Connecting the supplied FM and AM indoor antennas Connecting antennas Note Insert one end of the AM antenna cord to either of the AM antenna connectors and the other end to the other connector. There is no difference between one end of the AM antenna cord and the other end, unlike the speaker cables which have positive and negat[...]

  • Page 15

    15 Connecting an Outdoor FM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead. FM 75 Notes • Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft. • For best results, install the outdoor FM an[...]

  • Page 16

    16 Connections f or remote contr ol ( ) Notes • Connect the plugs securely. • Be sure to connect to the connectors using the cable. • For proper operation the audio connection cables must be connected. This applies to both remote and standard operation. • If a component has two terminals, you can use either one to connect to the HT-R8230. T[...]

  • Page 17

    17 Enjo ying m usic or videos with the HT -R8230 Connecting the power 1. Connect the power cord to a wall outlet. The HT-R8230 enters standby mode. The STANDBY indicator lights up. 2. Press STANDBY/ON. The AV Receiver turns on. The display on the AV Receiver’s front panel light. At the same time, the STANDBY indicator goes off. Note To turn off t[...]

  • Page 18

    18 Speaker setup Front left Front right Center Surround left Surround right You need to set up the speaker configuration for the speaker system A (see page 12). (There is no speaker configuration setup for the speaker system B.) It is not necessary to set the parameters again once you have completed the setup unless you change the speaker configura[...]

  • Page 19

    19 Speaker setup Specifying speaker distances To get the best from surround sound, it’s important that the sound from each speaker reaches the listener at the same time. To achieve this, you need to specify the distance from each speaker to the listening position. 1. Measure and make a note of the distance from each speaker to the listening posit[...]

  • Page 20

    20 SUBWOOFER MODE TEST LEVEL CH SEL Adjusting each speaker ’ s relative volume balance — Test tone Adjust each speaker’s relative volume balance so that the volumes of all speakers’ test tones sound equal at the listening position. Adjust the volume to your normal listening level, prior to commencing settings. Note You cannot adjust the vol[...]

  • Page 21

    21 Switch the source from TAPE to MD You can set the AV receiver to show “MD” when the TAPE source is selected by pressing TAPE on the unit. 1 Press TAPE to select the input source. 2 Press and hold TAPE on the unit until the display changes (for about 2 seconds). To restore the display Press and hold TAPE on the unit until the display changes [...]

  • Page 22

    22 Listening to the radio Tuning into a radio station 1. Press TUNER. The selected band appears in the display. Each time you press the button, the band changes as follows: AM ↔ FM. e.g. When FM is selected. 2. Using the TUNING / buttons on the front panel, tune into the station you desire. When you tune into a radio station, TUNED indicator appe[...]

  • Page 23

    23 PRESET TUNER PRESET/ADJUST TUNER MEMORY FM MODE Selecting preset stations Before selecting preset stations, you need to preset the radio stations. See “Presetting radio stations” on the left column of this page. 1. Press TUNER to switch the input source to the tuner. “FM” or “AM” appears in the display. The band selected in this step[...]

  • Page 24

    24 MUTING SP A/SP B SPEAKERS A/B Muting the sound (remote controller only) Press MUTING. The MUTING indicator flashes in the display during the muting mode. To restore the sound, press MUTING again. Tip If you turn off the unit during muting, and turn it on again, the sound will be restored. Listening through headphones Connect the plug of the ster[...]

  • Page 25

    25 DISPLAY DIMMER DIMMER SLEEP Changing the display Press DISPLAY. Each time you press DISPLAY, the screen changes as follows: When an input source other than FM or AM is selected FM/AM + Listening mode FM/AM frequency + Preset no. Input source + Listening mode (or Multich) Input source + volume Program format* Controlling the brightness of the dis[...]

  • Page 26

    26 DVD AUDIO SELECTOR DVD LEVEL AUDIO SEL CH SEL Adjusting each speaker ’ s relative volume balance temporarily You can readjust each speaker’s relative volume balance according to your preference while listening to the sound. The adjusted values will return to the values set on page 20 when the AV Receiver enters standby mode unless you save t[...]

  • Page 27

    27 DVD TAPE AUDIO SELECTOR DVD AUDIO SEL DIRECT SURROUND CH SEL LEVEL DIRECT SURROUND Using analog multi channel input The multi channel input refers to a system, which is compatible with a source component equipped with analog 5.1-channel outputs (DVD player, MPEG decoder, etc.), reproducing the left/right front, center and left/right surround cha[...]

  • Page 28

    28 The surround sound of the AV Receiver enables you to enjoy the presence of a movie theater or concert hall in your room. Before using any surround mode, make sure the Speaker Setup configurations have been set (see page 18). The speaker configuration is very important for the surround sound. See “Positioning speakers/Connecting speakers” on [...]

  • Page 29

    29 Selecting the listening mode Before operating the remote controller, press RCVR/TAPE. Press one of the listening mode buttons. DIRECT button : Set the listening mode to “Direct”. STEREO button : Set the listening mode to “Stereo”. SURROUND button : Set the listening mode to “PLII” (when the sound is analog, PCM or Dolby Digital stere[...]

  • Page 30

    30 Using the audio adjust functions Before operating the remote controller, press RCVR/TAPE. These functions only work with speaker system A. Audio Adjust provides various functions for adjusting the sound, including several especially for use with Dolby Digital, DTS, and Pro Logic II source. The following table lists the Audio Adjust functions, th[...]

  • Page 31

    31 The Audio Adjust functions are explained below. Bass With this function you can boost or cut low-frequency sounds output by the front speakers from –12 dB to +12 dB in 2 dB steps. Treble With this function you can boost or cut high-frequency sounds output by the front speakers from –12 dB to +12 dB in 2 dB steps. Late Night (Only for Dolby D[...]

  • Page 32

    32 To record the input source signal you are currently watching or listening to Recording of video and/or audio signals can be performed on the components connected to the VIDEO 1 OUT and TAPE OUT (audio only) jacks. Recor ding a sour ce Recording the video from one source and the audio from another You can add the sound from one source to the vide[...]

  • Page 33

    33 Using the remote contr oller with y our other A V components Connecting your Onkyo CD player, Onkyo DVD player, or Onkyo cassette recorder to the HT-R8230’s connector allows you to control it with the HT-R8230’s remote controller. Since you only need to point the remote controller at the HT-R8230, you can control components that are out of s[...]

  • Page 34

    34 Using the remote controller with your other AV components 1. TAPE input selector 2. RCVR/TAPE Tape mode (RCVR/TAPE) 3. Tape deck operation buttons 4. DVD operation buttons 2. CD CD mode 1. CD input selector : Power On/Off. : Starts playback of CD. : Stops playback, fast forward or fast reverse. : Fast forwards of CD. : Fast reverses of CD. : Let[...]

  • Page 35

    35 Causes • The power cord is disconnected. • There is external noise interfering with the computer circuits of the A V receiver . • Amplifier protection circuitry has been activated. • Power supply fluctuations or other abnormalities such as static electricity may interrupt correct operation. • The muting function is activated. • The A[...]

  • Page 36

    36 When incorrect operation is observed • The HT-R8230 contains an internal microcomputer that performs high-level operations. However, on extremely rare occasions, noise or interference from an external source or static electricity may cause faulty operation. If this occurs, unplug the power cord from the wall outlet, wait five or more seconds, [...]

  • Page 37

    37 Specifications Amplifier Section Power Output: Front L/R: 100 W + 100 W Center 100 W Surround L/R 100 W + 100 W (8 Ω , 20 Hz~20 kHz, FTC) Dynamic Power: 230 W + 230 W (3 Ω , Front) 170 W + 170 W (4 Ω , Front) 115 W + 115 W (8 Ω , Front) THD (Total Harmonic Distortion): 0.08 % (Power Rated) Damping Factor: 60 (Front, 1 kHz, 8 Ω ) Input [...]

  • Page 38

    38 Memo[...]

  • Page 39

    39 Memo[...]

  • Page 40

    SN 29343866 D0406-1 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzel[...]