Planet Technology DVR-470, DVR-1670 manuel d'utilisation

4/16-Channel H.264 Digital V ideo Recorder DVR-470 DVR-1670 USER’S MANUAL Page 1[...]

Copyright Copyright © 2007 by PLANET T echnology Corp. All rights reserved . No part of t his publicat ion may be repro duced, transm itted, transcribed, st ored in a retrieval system, or translated into any language or computer language, in any form or by an y means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, with o[...]

Federal Communication Commission (FCC) Radiation Exposure S tatement This equipment complies with FCC radiation expo sure set forth for an uncontrolled environment. In order to avoid the possibility of ex ceeding the FCC radio frequency expo sure limits, human proximity to the antenn a shall not be less than 20 cm (8 inches) during normal operation[...]

Content Chapter1 Produc t Introduction .................................................................................................. 6 1.1 Summary ................................................................................................................... 6 1.2 Features ...................................................................[...]

5.18 T ransaction In formation .......................................................................................... 76 Chapter6 Utili ties .................................................................................................................... 80 6.1 Save Parameters .................................................................[...]

Chapter1 Pr oduct Intr oduction 1.1 Summary DVR-470/DVR-1670 H .264 network digital video recorder is an excellent digital surveillance p roduct. It uses the embedde d MCU and real time opera ting system, combining the most advanced technology in Inform ation Industry such as video an d audio encoding/decodin g, hard dis k record and TCP/IP . The f[...]

z Support cycle or no ne cycle record. z Support backup the rec orded files and clips. Supp ort USB memory , USB HD D, USB CD-R/W , USB DVD-R/W , IDE CD-R/W and IDE DVD-R/W . Preview and playback z Support analog m onitor and VGA output. z Support multiple preview modes. z Support sensitive area m ask. z Support camera spiteful block alarm . z Supp[...]

Chapter2 Installation Warning：Before you inst all the DVR, please ma ke sur e the power of DVR is off. 2.1 Checking the DVR and It s Accessories When you get the pro duct, check t hat all the item s are included in your product pac kage. There is a list in the package. If any of the items is m issing, please contact your dealer . 2.2 HDD Inst all[...]

2.3 Rear Panel Description Notice ： Pl ea se re fe r to rea l pr oduct for different model. DVR-470 Rear Panel DVR-1670 Rear Panel Index Physical Interface Description 1 V ideo Input St a nd a r d B NC . V ideo Output Connect monitor , output video and menu. 2 Audio Output 1 channel RCA (1.0 Vp-p, 75 Ω ) 3 Audio input 4 channel RCA (1.0 Vp-p, 75[...]

External Alarm Input 4/8/16 Alarm in . Relay Output 2/4 Alarm out 8 AC Input 100V~240V A C 2.4 External Alarm In/Out Connection Alarm input port ： G (GND) ： Conenct the GND of sensor . 1~16 ： Alarm input , support norm al open/normal close. 0 ： Reserved. Alarm outp ut ： 1G~4G ： 4 relay output. Alarm output connection Please note the usa[...]

Chapter3 Operational Instructions 3.1 Front Panel n o p q r Index T ype Name Description 1 Sta t e Lamps READY ST A TUS ALARM RECORD NETWORK DVR is ready . Green means you can use I R re mote control. Red means there is alarm . T wink le in red means read ing or writing HDD. Network status. 2 Lamp IR receiver . Numeric Keys Input number , lower cas[...]

REC PTZ PREV A SHIFT 1. Manual record; 2. 【 SHOT 】 in PTZ control (adjust preset). 1. Enter into PTZ co ntrol mode; 2. 【 IRIS- 】 in PTZ control.. 1. Multi screen p review switch; 2. Switch m enu mode into pre view; 【 FOCUS- 】 in PTZ control. 1. Input switch (number , lower case, upper case and symbol); 2. 【 FOCUS+ 】 in PTZ control; [...]

3.2 IR Controller Index Name Description 1 POWER T urnoff device. 2 DEV Enable/Disable IR rem ote control 3 Numeric Keys Same as num eric keys of front pan el. 4 EDIT Same as EDIT key of front panel. 5 A Same as A key of front panel. 6 REC Same as REC key of fro nt panel. 7 PLA Y Same as PLA Y key of front panel. 8 INFO Same as INFO key of fron t p[...]

15 Reserved 16 F1 Same as 【 F1 】 key of front panel. 17 Lens control IRIS, FOCUS ZOOM for lens control. 18 F2 Same as 【 F2 】 key of front panel. Loading the batteries into the IR contr oller 1. Remove the ba ttery co ver . 2. Insert the batt ery . Please take care that the poles (+ and -) are correctly positioned. 3. Replace the battery cov[...]

3.3 Menu Description 3.3.1 Menu Items Menu Name Function Menu Name Function Display Unit name Device ID Require password Screen saver V ideo stan dard Brightness Menu transparency VGA resolution DST Date and T ime Image Camera name and position set up Adjust Brightness, Contrast, Hue and Saturation OSD Display mode, position an d OSD format setup M[...]

Tr a n s a c t i o n T ext input mode A TM IP addre ss A TM type T ext inform ation Utilities Restore parameters Upgrade firmware HDD management Clear alarm output Reboot Power off V iew log System information 3.3.2 Menu Operation How to enter into menu mode z Press 【 MENU 】 key to enter into DVR main menu. z Press 【 PLA Y 】 short key to en[...]

Each menu contai ns differ ent kinds of items. There is a small rectangular fra me named “Active Frame” whic h is pointing to the s elected item. This “ Active Fram e” can be moved by 【 Æ 】 or 【 Å 】 keys. There are such kinds of menu ite ms ： 1. Check Box ： Provide 2 options, “ 9 ” means enable and “ × ” means disable[...]

3.4 Character Input In the menu i nterface, if you enter into edit sta tus (for example, in the “ camera name” edit box), at the bottom of screen, the input status is appeared ： Here it means you ca n press num eric keys to input d igital num b er . Press 【 A 】 key to chan ge input m ethods. Y ou can select “ nu mber”, “Upperc ase?[...]

Chapter4 Basic Operation Guide 4.1 Power on Note ： Please make sure the power suppl y matches DVR and AC cable connected correctly . Befor e switch DVR on, please connect one monitor with V OUT or VGA interface. Otherwise, you can not see gra phic user interface and can not operate. If 【 POWER 】 lamp is off, please do as followin g ： Ste p [...]

Camera record status is fo llowing ： Icon Icon Color S tatus Description White No video sign al Y e llow Vdieo input Pink Manual recording Green Real time recording Blue Motion detect recording Red External alarm recording Page 20[...]

Ca mera alarm status is following ： Icon Icon Color S tatus Description White V ideo signal lost Y ellow V i ew tampering alarm Pink Motion&External alarm Green No alarm Blue Motion alarm Red External alarm Press numeric keys to switch over in dividual camera previ ew . If DVR has less than 10 channels, pres s one numeric key to switch corres[...]

4.3 User name and p assword Note ： When DVR is delivered fr om factory , there is only one default administrator named “admin”, and password is “1234 5”. The admi nistrator’s name can not be modified, while the passwor d can be modified. The ad ministrator can create 15 users and define their user rights. Login Login dialog i s followin[...]

Setp 2 ： Enter into password modificati on menu Move the “Ac tive Frame” to “ Password” icon by using 【 Æ 】 / 【 Å 】 keys. Press 【 ENTER 】 key to enter into fo llowing password m enu ： Ste p 3 ： Input new password Press 【 EDIT 】 key to enter into e dit box. Y ou can use num eric keys to input new password. The passwor[...]

4.4 PTZ Control Note ： The user must have the “PTZ control” right. PTZ contr o l interface In preview mode, press 【 PTZ 】 key , i n the login dialo g , select one user nam e and input the correct password, you can e nter into PTZ control interface. In menu mode, press 【 PTZ 】 key , you can enter into P TZ control interface directly . [...]

Adjust preset description In PTZ control mode, press 【 REC/SHOT 】 key , and press the preset num ber (three numeric keys), DVR will adjust t he corresponding preset num ber . Repeat pressing 【 REC/SHOT 】 key , and press the preset number , DVR will adjust that preset number . When you exit PTZ contr ol mode, the camera will stay at the curr[...]

4.5 Manual Record Note ： The user must have the corr esponding right, DVR has HDD and HDD is formatted already . Manual record In preview mode, press 【 REC 】 key , in the pop-up login dia log, select the name and inp ut the correct password, you can e n ter into the “ Manual Record” interface. In menu mode, press 【 REC 】 key to enter [...]

4.6 Playback Note ： The user must have “P layback” right. Playback interface In preview mode, press 【 PLA Y 】 key , in the pop-up l ogin dialog, sel ect username and input correct password, you c an enter into “P layback” interface. In menu mode, press 【 PLA Y 】 key , you can enter into “Playback” int erface directly . Playbac[...]

Play by T ime ： Playback the recorded stream directly based on the tim e section. Select Page ： In the file l ist box, each page will only display 8 files. If th e matched files are more than 8, you can select page to list o ther files. 500 pages (4000 files) can be searched in one time. Y ou can use numeric keys or 【↑】 【↓】 keys to [...]

3. Search by Card No and Playb ack file ： In the playback interface, select channel number , record type, enable card No. search option (“ 9 ”) and input the card number , move “ Active Frame” to “Search” butt on, press 【 ENTER 】 key , DVR will se arch and list the matched files. If the matched files are m ore than 8, you can use [...]

Exit playback In playback interface, press 【 ESC 】 key to enter into previ ew mode. In playback interface, press 【 MENU 】 key to enter into main menu, press 【 REC 】 key to ent er into manual record, and press 【 PTZ 】 key to enter into PTZ con t rol mode. Page 30[...]

4.7 Backup Recorded Files Note ： The user must have “Playback” right. Pl ease connect with ba ckup devices before you start to backup. In the playback interface, you can bac kup the recorded files. In the preview m ode, press 【 PLA Y 】 key , in th e login dia log, select usern ame and inpu t the correct password, you can e n ter into the [...]

St e p 2 ： Select the files that you want to backup In the file list box, use 【↑】 or 【↓】 keys to m ove the scroll bar . W hen the scroll bar stays at the file you w an to backup, press 【 EDIT 】 key to select it. The sym bol “ 9 ” is the sel ection tag. Y ou can use the same method to s elect other files you want to backup. Aft[...]

4.8 Shut Down DVR Note ： Do not switch off the power d irectly in ca se of damaging H DD. The correct step is using “Power Off” in the “Utilities” menu, or 【 POWER 】 key on the front panel or on IR controller . Shut down DVR normally Use menu Enter into “Util ities” menu, m ove “Active Frame” to “Power Off” button and e nt[...]

Chapter5 Parameters Setup Guide Only the users that have “ Parameters Setup” righ t ne ed read this chapte r . When the following parameters are modified and saved, you must reboot the DV R to make the new p arameters take into ef fective. Other parameters do not need to reboot. z Any network param eters z Stream type, resolution and record sch[...]

Move “Active Frame” to “ User” icon, press 【 ENTER 】 key to enter into “ User Management” menu. In the user nam e list box, only “ admin” is existe d. Y ou can use 【→】 key , move “Active Frame” to pass word edit box, a nd press 【 EDIT 】 key to enter into edit status. Press num eric keys to input the new password. T[...]

5.2 Add and Delete User Enter into “User Manag ement” interface. Add user The steps are following ： St e p 1 ： Enter into “User Manage ment” menu Please refer to chapter 5.1 St e p 2 ： Add new user name In the “User Manag e ment” m enu, move “A ctive Fram e” to “Add” button and press 【 ENTER 】 , in the pop-up dial og, [...]

In the users list b ox of “User Managem ent” menu, use 【 Ç 】 【 È 】 keys to select the new user name, then us e 【 Æ 】 key to “Default Rights” button, press 【 ENTER 】 , the user will have the default rights. The default rights in clude local p layback, rem o te playback an d view log. If you want to define t he detail right[...]

“Remote Rights” ： PTZ Control ： Remote control PTZ ; Record ： Remote m anual start/stop recording; Playback ： Remote playback, download the record ed files on DVR; Parameters Setup ： Remote setup t h e DVR parameters; Log ： Remote view the log on D VR; Utilities ： Remote upgrade firm ware, format HDD, reboot DVR and shut down DVR,[...]

5.3 Unit Name and Device ID Unit name In the “Display ” menu ： There is an item named “Unit Name”. The default unit name is “Embedded Net DVR”. Move “Active Frame” to unit name edit box, press 【 EDIT 】 key to enter into e dit status, you can modify the unit nam e. About how to input characters, pleas e refer to chapter 3.4. Pr[...]

5.4 V ideo Output St andard and VGA Setup V ideo output standard There is one VOUT BNC connector at the rear panel of DVR. It is used to conn ect with analog monitor an d can support P AL or NTSC video output. Y ou can modify vid eo output standard to match video input. In “Display” menu ： There is a list box nam ed “V ideo Output Standard?[...]

5.5 OSD Setup OSD is abbrevia tion of “O n Screen Display ”. For our embedded D VRDVS, it includes displaying system time and camera name. OSD settings include ： System time, time format, tim e display position, camera name, cam era name display position, etc. System Time In “Display” m enu, you can setup DVR system date and time. Display[...]

Display mode ： There are several display modes ： Opaque&S teady , T ransparent&Steady , T ransparent&Flashing, Opaque&Flashing, Move “Active Frame” to “ OSD” item, you can select one mode. Display position and format ： Mov e “Active Fram e” to “Position” bu tton on the right side of “OSD”, press 【 ENTER ?[...]

Chapter 3.4). The camera name can support 32 chara cters. St e p 3 ： Press 【 ENTER 】 key to exit ed it status. Move “Active Frame” to “C onfirm” button, press 【 ENTER 】 to save the modification and you can see the new cam era name. Press “Cancel” button or 【 ESC 】 key t o abort. Setup Camera Name Position If you do not w a[...]

5.6 V ideo Parameters Setup For different camera and different background, in order to get the best video image, you need to adjust vide o parameters such as brightenss, saturation , contrast and hue , etc. Y ou can setup the camera indivi dually , and also you can copy the v ideo param eters of one camera to any ot her ca meras. Here are the setup[...]

5.7 Mask Area Setup In some cases, m aybe you want mask the sensiti ve area. This area will not be prev iew and recorded. The mask area setup steps are following ： St e p 1 ： Enter into “Image Setup” menu ： St e p 2 ： Select o ne came ra ： Y ou can use 【 Ç 】 【 È 】 keys to select one camera. St e p 3 ： Enter into mask ar ea[...]

(22*15 for NTSC), you c an use 【↑】 【↓ 】 【→】 【←】 keys to move the y ellow pane to your hope po sition and press 【 EDIT 】 key , the yell ow pane will be turned into red, then you can use 【↑】 【↓】 【→】 【←】 keys to extend the red pane. This red area is the mask area. After you make sure the red m ask ar[...]

5.8 V iew T ampering Alarm If you enable this function, whe n someone blocks the c amera spitefully , DVR will make warning alarm. St e p 1 ： Enter into “Image Setup” memu ： St e p 2 ： Select camera ： Please use 【 Ç 】 【 È 】 keys to sele ct one cam era. St e p 3 ： Select sensitivity ： Y ou can use 【↑】 【↓】 keys t[...]

St e p 6 ： Alarm schedule setup ： When there is view tampering alarm happene d, DVR will handle the a larm based on the schedule. Y ou can set 4 per iods for each d ay one w eek. Also you can copy the schedule of one day to other days. Notes ： T ime periods can not be repeated. Please re boot DVR to mak e the paramete rs into effecti ve. St e[...]

5.9 V ideo Loss Alarm When the video c able or camera has something wron g, the video im age is lost. If you enable video loss alarm , in such case, DVR will make alarm. St e p 1 ： Enter into “Image Setup” menu ： St e p 2 ： Select camera ： Use 【 Ç 】 【 È 】 keys to select one cam era. St e p 3 ： Enter into “V ideo Signal Los[...]

St e p 5 ： Setup alarm policy ： Y ou can select one or more respo nse solutions, inc luding “On Screen W arning”, “Audible W arning”, “ Upload to Center” and “T rigger Alarm Output”. Y ou can use 【↑】 【↓】 and 【 EDIT 】 key to enable or disable them. “ × ” is disable and “ 9 ” is enable. St e p 6 ： Save a[...]

5.10 Motion Detection Alarm If you enable this funct ion, when there is m otion detected, DVR will make alarm . St e p 1 ： Enter into “Image Setup” menu ： St e p 2 ： Select camera ： Use 【 Ç 】 【 È 】 key to select one cam era. St e p 3 ： Select motion dete ction sensitivity ： On the right side of “ Motion Det. Lev el” it[...]

The whole screen is divi ded into 22*18 pan es (NTSC ： 22*15). There is one yellow panel on the upper left side. The motion area se tup steps are the s ame as that of m ask area setup (refer to chapter 5.7). The only differences are that you can use 【 PTZ 】 key to set the whole screen as motion area, a nd mutil m otion areas can be def ined. [...]

St e p 6 ： Motion alarm r ecord channel setup ： When there is motion alarm happ ened, you can trigger relate d camera to start re cording. In “Motio n Alarm Handle” menu, yo u can select one or more record channel s. Please use 【 ENTER 】 or 【 EDIT 】 key to enabl e the flag into “ 9 ”. Note ： In order to make the cam eras start[...]

5.1 1 Preview Properties In “Preview” menu, you ca n setup previe w mode, screen sw itch tim e, enable or disable audio preview and preview layout. St e p 1 ： Enter into “Pr eview” menu ： In the main menu, m ove “Active Frame” to “Preview” icon and press 【 ENTER 】 , you can enter into “preview” m enu. St e p 2 ： Previe[...]

Preview layo ut setup ： There is a square frame divide d into many windows. If you select “4 Screen”preview m ode, this fram e is divided into 4 win dows. Each wind ow represents one camera. Y ou can move “Active Fram e” among the window s. There is one bar under the square to display the preview order of all cameras. First select the big[...]

5.12 Recording Setup In main menu, there is an i con named “Recor ding”. Y ou can enter into recordin g menu as following ： “Recording” menu description ： If HD Full ： There are two options ： “Overwrite” and “S top recording”. If you selec t “Overwrite” option, when all HDDs in DVR are full, DVR will overwrite the earlie[...]

If you select varia ble bit rate, DVR will adjust the actual bit rate according to the video movement. When there is not m uch movement, DVR will use low bit rate, while there is much movement , DVR will use high bit rate . In this case, DVR can save HDD usage and network bandwidth. If y ou select fixed bit rate, DVR will use the fi xed bit rate to[...]

Note ： When the cam era’ s recording sch edule is modified, y ou must reboot DV R to make it into effe ctive. All day re cording setup ： St e p 1 ： Enter into r ecording schedule menu In recording m enu, use 【 ENTER 】 or 【 EDIT 】 key to enable record functi on (“ 9 ” flag), press “Schedule” bu tton to enter into recording sc[...]

St e p 1 ： Enter into r ecording schedule menu In recording m enu, use 【 ENTER 】 or 【 EDIT 】 key to enable record functi on (“ 9 ” flag), press “Schedule” bu tton to enter into recording schedul e menu. St e p 2 ： Select ond day and disable all day r ecording option For “Day” item, there are options ： Monday , T uesday , W[...]

5.13 External Alarm Input and Relay Output For DVR-470, there are 4 external a larm inpu t and 2 relay out put. For DVR-1670, there are 16 external alarm input and 4 relay output. In “Alarms” menu, you can setup for each external alar m input. In m ain menu, m ove “Active Frame” to “Alarm s” icon and press 【 ENTER 】 key to ente r in[...]

St e p 4 ： Alarm trigger record channel setup Y ou can sele ct channels to record for each alarm input. In the sub m enu, you can use 【 ENTER 】 or 【 EDIT 】 key to enable recor d channel. “ × ” means disable a nd “ 9 means enable. Note ： In order to trigger the chan nel to record, in “Recording” m e nu, you must enable recordi[...]

First select one cam era, then select one of following PTZ linkage ： z Preset ： Set the flag as “ 9 ” to enable preset, in the preset num ber edit box and input one preset number tha t has been setup a lready . Please refer to chapter 5.15 for preset setup. z Sequence ： Set the flag as “ 9 ” to enable sequence and in put one sequence [...]

St e p 3 ： Enter into alarm out schedule Y ou can set the schedule to m ake alarm output i n to ef fective. Move “Active Frame” to “Schedule” bu tton on right s ide of “Alarm Out T ime” ite m, press 【 ENTER 】 key to enter into the corresponding schedule m enu ： St e p 4 ： Setup alarm out schedule Like other schedu le setup, yo[...]

5.14 Network Parameters If you want use ne twork to access DV R, you m ust setup network para meters. Note ： If any network parameter is modified, you m ust save and reboot DVR to make it into effecti ve. In main menu, m ove “Active Frame” to “N etwork” icon and press 【 ENTER 】 , you can enter into “Network” menu as fol lowing ：[...]

This DNS is special s oftware, not the normal dom ain name server . Y ou can use the provided SDK to develop this DNS software. Multicast IP ： It is one D-class IP address, am ong 224.0.0.0 --- 239.255.255.255. If you do not use m u lticast functi on, you do n ot need to s et. Some routers will prohibit multicast function in ca se of network stor[...]

PTZ menu description Select channel ： Select one PTZ camera. RS-485 parameters ： Incl uding baudrat e, data bit, stop bit, parity , flow control, etc. These parameters must be the same as thos e of PTZ. Protocol. PTZ addr ess ： Each PTZ has one dif ferent address. PTZ type ： DVR had the following PTZ protoc ol ： Y ouLi, LinLin-1016, LinLi[...]

Cruise setup ： Cruise is remem bering the track of P TZ m ovement. Please make sure the PTZ you are using can s upport cruise function. Preset setup In “P TZ” menu, move “Active Frame” to “Setup” but ton on the right side of “ Preset” item, press 【 ENTER 】 , you can ent er into “Preset” setu p menu ： Add preset number ?[...]

In “Sequence” setup menu, first input the se quence num b er . The sequence is am ong 1 --- 16. Each sequence is m ade up of cruise points, and each c ruise point includes preset num ber , dwell time and dwe ll speed. Dwell tim e is the time staying at that pres et number . Dwell speed is the speed that PTZ is m oved to that preset num ber . Pr[...]

Press “RecCru” button, you will e nter into “PTZ contro l” interface. Y ou can start controlling PTZ with direction keys, press 【 ENTER 】 to save the operation tr ack and return “Cruise” setup menu. Press “S tartCru” button to repeat th e PTZ track until you press “S top” button. Press “Return” button ba ck to “PTZ” [...]

5.16 RS232 setup There is one RS-232 port at DVR rear pane l. In main menu, m ove “Active Frame” to “RS232” icon and perss 【 ENTER 】 key , you enter into “RS232” setup m enu ： RS232 menu description RS-232 parameters ： In cluding baud rat e , data bit, sto p bit, parity , flow control, etc. Wo r k m o d e ： The RS-232 can be u[...]

Username, password and V erify passw ord ： Only used when work mode is “PPP”. Used for login when remot e PC dialup throug h PSTN. Phone ： Only used when work m ode is “PPP” and PPP mode is “Active”. It is the phone number of remote PC. Callback and Data Encr yption ： Only used when w ork mode is “PPP”. They are not available.[...]

St e p 3 ： Save setup In “Recording” menu, press “Confirm ” button to save parameters. St e p 4 ： Setup Modem used on DVR side Use DCE calbe to connect Modem with PC serial port. Y ou can use HyperT erminal or NetT erm to setup modem ： A T&F ---- Retore default parameters (Gen erally , Modem is hard flow contr ol) A T&S0=1----[...]

Page 73[...]

St e p 3 ： Establish the dialup connection Select the Modem connected with PC just like the d ialup networ k connection , input the telephone nu mber connecte d with DVR’ s modem. Input the user name, password. They m ust be the same as that DVR PPP setup. St e p 4 ： During the dialup connection , it will give th e message of “verification [...]

5.17 Exceptions The exceptions can be handled at present include ： hard disk full, hard disk error , illegal access, IP address conflict, network fai lure, and NTSC/P AL dif fer . Enter into “Excep tions” menu ： Including the fol lowing handl e methods ： Audible W arning ： DVR beep warning. Upload to Center ： Send exception inform ati[...]

5.18 T ransaction Information The DVR can actively obtain or passively recei ve the credit card number from A TM machine linked throug h network or serial port, and credit card num ber can be overlay on live video, recorded and pl ayback. The foll owing description indicates how to carry out relevant parameter setting ac cording to differe nt links[...]

Start & e nd position and length of transa ction type T ransaction type and c ode When the A TM machine is sending transacti on in formation to bank center , DVR will capture the data packa g e through netw ork, and analys e the data according to the format. Then DVR will overlay the corres pond text on live video. 2. Network r eceive ： DVR r[...]

In the case, you m ust set the RS-232 of DVR as transparent channel m ode as following ： A software must be run in the A TM machine, and send the credit c a rd number , transaction code to DVR through RS-232 port. Please provide deta il A TM machine comm unication protocol for actu al projects. 4. Receive the command sent by A TM through serial p[...]

In the case, you m ust set the RS-232 of DVR as transparent channel m ode as following ： Also, a software must be run in A TM machine, and send command to DVR throug h RS-232 port based on special communi cation protocol. Page 79[...]

Chapter6 Utilities There are man y tools in “Uti lities” menu. Includi ng “SavePa ra”, “Resto rePara”, “Up grade”, “Hard Disk” , “Stop Alarm Out”, “Reb oot”, “Power Off”, “V iew Log” and “System Info ”. Enter into “Ut ilities” menu ： 6.1 Save Parameters Save factory default param eters into FLASH mem o [...]

6.3 Upgrade Y ou can use this function to upgrad e the firm ware. Please confirm the lan g uage is matched . Press “Upgr ade” icon, in the pop-up dialog, you can select eit her “FTP” or “USB ” upgrad e mode. If you select “FTP” m ode, you will enter into “FTP Upgrade” menu ： Input the ftp server IP and press 【 ENTER 】 key [...]

6.4 Hard Disk Management Check HDD work status Capacity , Free space, Stand by or not, Normal status or not. Format HDD Before formatting stop all recording. After form atting, you must reboot DVR, ot herwise DVR will not work norm ally . 6.5 Clear Alarm Out Clear the alarm output manually . 6.6 Reboot Reboot DVR. 6.7 Power Off Shut down DVR. 6.8 V[...]

If you want to view the log based o n default option , just press 【 ENTER 】 key . DVR will list all matched inform ation. Also you can select options to search (By T ype, By Date, By T ype&Date). By T ype T o view log information of the ass igned type. T y pe is divided i nto “Major type” and “Minor type ”. Major type inclu des oper[...]

St e p 4 ： When searching is finished, DVR will lis t all matched alarm inform ation. In the list box, the inf ormation includ es ： Index, Occur T ime, Major T ype, Minor T ype, Panel User , Net User , Host Address, Para. T ype, Channel No, HDD No, Alarm In and Alarm Out. Y o u can press “More Info” butto n for more inform ation, also slect[...]

6.9 System Information Press “System Info” icon in “Utilities” m e nu, you can g et DVR system information ： Page 85[...]

Chapter7 Firmwar e Upgrade The DVR firmware is stored in FLA SH ROM. Y ou can use DVR upgrade function t o write the firmware file ( d igicap) into FLASH. There are two cases that you need to upgrade DVR firmware. One is update old fir mware. The other is when the code in DVR FLASH is crashed. Note ： Make sure that the DVR and the firmware ar e c[...]

3. Select “Users/rights ” under “Security” menu item . The following dia log box will be pop-up. 4. Create new us er . Click “new user’. New user dialog pops up . Input user nam e “target”. Click “OK”. 5. In the password dial og, input password “t arget” in “New Password” a nd “V erify Password” edit box. Click “OK[...]

6. In the “User/Rights Security ” Dialog, select “User Name” as “tar get”. In “Home Directory” edit bo x, input the pat h where the firm ware file (digicap) is placed. Then press “Done” to exit. 7. Next tim e, you need not setup again, just d ouble click a nd open “wftpd3 2.exe” to upgra de the DVR/DVS firmware. Page 88[...]

7.2 Upgrade Mode 1. Use client software to upgrade the f irmware file. Y ou do not need to use ftp s erver software. Please refer to the client softw are user manual for detail inform ation. 2. Use “FTP” function of “ Upgrade” sub menu in “Utiliti es” menu. Y ou need one host PC to run FTP server software and place firmware file (di gic[...]

Appendix A DVR Connect Cable Definition 1 UTP network connect cable made method Material and tool One twist cable (8 pin, the length can b e defined as to t he actual dem and, but must be within 100m), 2 standard RJ4 5 head, one tool for RJ45. Suggestion ： have a network cable t e st tool to test each cable made. Pin definition T o m ake the netw[...]

The corresponding relationship of cr oss cable 2 RS-232 connect cable made method DVR-802x has standard DB9 RS-232 int erface, like PC COM port. Pin definition “I” means DVR input and O means DVR out put. Pin index Name I/O Description 1 DCD I Carrier Detect 2 RXD I Receive Data 3 TXD O T ransfer Data 4 DTR O T erm inal Device Ready 5 GND Groun[...]

Appendix B Specifications Model name DVR- 470 DVR-1670 V ideo compression H.264 Preview resolution PA L ： 704*576 (4CIF), NTSC ： 704*480 (4CIF) Playback resolution CIF/QCIF V ideo inp ut 4 16 V ideo inp ut interface BNC (Electrical Level ： 1. 0Vp-p, resistance ： 75 Ω ) V ideo out put 1 channel, BN C (Electrical Level ： 1.0Vp-p, resistan[...]

Power supply 100~240V AC, 6.3A, 50~60 H Z Power consumption 20--42W (without HDD) Wo r k i n g temperature -10 ℃--＋55℃ Wo r k i n g humidity 10 ％ --90 ％ Size 14.25 inch s tandard (440m m*390mm *70mm) We i g h t ≤ 8Kg (without HDD and CD-R/W) PA L ： 176*144(QCIF), 352*28 8(CIF), 704*288(2CIF), 528*384 (DCIF), 704*576(4CIF); NTSC ： 17[...]

Appendix C List of Recommended DVR Peripherals USB DVD-R/W ： 1. LG GSA-E10L 2. BENQ EW164B USB CD-R/W ： 1. BENQ external 5232WI-ok2 2. ASUS CR W -4824A + USB Convertor case 3. SONY CD-R/R W CRX230AD + Convertor cable 4. SONY CD-R/R W CRX225E + Convertor cable 5. BENQ external EW162I-OK2 IDE CD-R/W ： 1. Sony CD-R/R W CRX225E 2. NEC DVD R/R W &[...]

W est Digital ： 1. WD Caviar WD400BB 2. WD Caviar WD800BB 3. WD Caviar WD1200BB 4. WD Caviar WD2000BB 5. WD Caviar WD2500BB 6. WD Caviar SE WD1600BB 7. WD Caviar SE WD2000JB 8. WD Caviar SE WD2500JB 9. WD Caviar SE WD3000JB Page 95[...]

Appendix D Quick Sear ch Function T able T ype Name Description Index User managem ent Create and delete users. Sy stem has one default administrator . The administrator c an create 15 users and define the i r rights. 5.2 Safety function Password Management Modify password. 4.3&5.1 HDD managem ent Format HDD, HDD information. 6.4 Recording mode[...]

Remote record Remote record real time stream . * Remote playback Remote playback the recorded files in DVR * Download Download recorded files in DVR. * Remote upgrade Remote upgrade firmware. * T ransparent channel Remote control serial devi ce connected with serial port of DVR. 5.16 W eb Using IE to access DVR * PSTN Access DVR through PSTN. 5.16 [...]

Appendix E T r oubleshooting Failur e Possible reas ons After plugging in power , turning on the power swi tch, “POWER” light in fro nt Panel does not turn on, and fan does not work. 1) Power cable is broken. 2) Power supply is broken. After plugging in power , turning on the power swi tch, “POWER” light in front pa nel turn to green while [...]

3) Old player SDK (playm4.dll) Notes ： 1) Place the DVR in well ve ntilated space so that it operates within the allowed r ange of temperature and humidity as in specification. 2) If the circuit board is wet, dust on circui t board can ca use a short cir cuit. The circ uit board, lug and socket , housing fan and housing should be cleaned by brush[...]