Rosewill EASYN400 manuel d'utilisation

W ireless Router RNX-EasyN400 User Manual[...]

Wir eless Router RNX-Eas yN400 User M anual 1 Safety Warning • Place connecting cables carefu lly so that no one w ill step on th em or stumble over them. • Always disconnect all cables from this device before servicing or disassem bling. • Use ONLY an appropriate power adaptor or cord for your device. • Connect the power adaptor or cord to[...]

Wir eless Router RNX-Eas yN400 User M anual 2 Table of Contents T AB LE OF CONTENTS ............................ ................................ ....................................... ........... .........2 BEFORE WE BEGIN ............. .............................................................................. ..................... ..........[...]

Wir eless Router RNX-Eas yN400 User M anual 3 3.7.1 Advanced .......................................................................... ....................................... ................. 58 3.7.2 Dem ilitarized Zone (D MZ) ................................................................................................. ...... 58 3.7.3 Denia [...]

Wir eless Router RNX-Eas yN400 User M anual 4 Before We Begin • Please configure RNX-EasyN400 with the comp uter that was last co nnected directly to your mo dem. • You can only use the Ethernet port on yo ur modem. If you were using the USB connection before using RN X-EasyN400, then you must turn off your modem, disconnect the USB cable and c[...]

Wir eless Router RNX-Eas yN400 User M anual 5 1 Introduction 1.1 Over view Congratulations on y our purchase of RNX-EasyN40 0 Wireless Network Broadband Router. RNX-Eas yN400 is compati ble wi th 802.11g & 802.11 b and draft 8 02.11n v2. 0. RNX-EasyN400 is not only a Wireless A ccess Point, but also dou bles as a 4-port full- duplex Switch that[...]

Wir eless Router RNX-Eas yN400 User M anual 6 enhance security WDS (Wireless Distribution System) Make wireless AP an d Bridge mode simultaneously as a w ireless r epeater ** Theoretical wireless signal rate ba sed on IEEE standard o f 802.11a, b, g, n chipset used. Actu al throughput may vary. Network condition s and envir onmental factors lower a[...]

Wir eless Router RNX-Eas yN400 User M anual 7 1.4 Product La yout and LED S ignal LED Colo r St a t u s Description On RNX-EasyN400 is receiving power and functioning properly. Blinking RNX-EasyN400 is performing test or reset POWER Am ber Off RNX-EasyN400 is not receiving power On RNX-EasyN400 is ready, but not sending/receiving wireless signals B[...]

Wir eless Router RNX-Eas yN400 User M anual 8 Blinking RNX-EasyN400 i s sending/receiving data th rough WAN Off The W AN is not ready or fail On RNX-EasyN400 has a succe ssful Ethernet connec tion. Blinking RNX-EasyN400 is sending/receiving data through LAN port LAN 1~4 port Blue Off The LAN is not ready or fai l WPS Press this button for 1 second [...]

Wir eless Router RNX-Eas yN400 User M anual 9 1.7 RNX-EasyN400’s LAN & WAN Cable Connection Setup W A N co nnect ion: Connect Ethernet cable between W AN ports of your ADSL/CABLE modem & INTERNET port of RNX-EasyN400. Make su re your ADSL/CABLE modem is working well. Contact your ISP if you have any q uestio ns. RNX-EasyN400 Rear View + I[...]

Wir eless Router RNX-Eas yN400 User M anual 10 RNX-EasyN400 LAN Connection Diagram[...]

Wir eless Router RNX-Eas yN400 User M anual 11 2 Setup Wizard We will introduce the Smart Wizard in this section. Please make sure the following before inser t the CD into the CD/DV D drive: • Internet connection should be setup & ready to use (ADSL or cable modem). • Modem must provide a RJ45 port to connect with RNX-EasyN400. ¾ Please re[...]

Wir eless Router RNX-Eas yN400 User M anual 12 Click User Manual to open user manual. Click Ad obe Reader to install Adobe Acrobat reader on your PC/Noteb ook. Click EX IT anytime you want to abort. 2.2 Setup Wizard – Configur atio n Click <Next> to proceed. Click <Exit> to abort. RNX-E asyN400 should be setup as depicted above.[...]

Wir eless Router RNX-Eas yN400 User M anual 13 Make sure your DSL/CABLE modem is setup and wo rking. Else take the help of y our internet service provider. Click <Next> to proceed. Check the MODEM and RNX-EasyN400 connection. It sho uld be as shown below. Check power connection for modem as well as RNX-EasyN400. Click <Next> to proceed.[...]

Wir eless Router RNX-Eas yN400 User M anual 14 Notice the LED will light up at this stage. If not, check your procedures again. Click <Next> to configure WAN & Wireless setting s. The Wizard page will show up as below:[...]

Wir eless Router RNX-Eas yN400 User M anual 15 Then, you will be prompt to RNX-EasyN400 login page User name and password are admin/adm in. C lick <OK> . Your default browser will connect to RNX-EasyN400 Web Server http ://192.168 .0.1 .[...]

Wir eless Router RNX-Eas yN400 User M anual 16 Click <Next> to ente r mode sel ectio n. 2.3 Setup Wizard – Con nect Mo de Sel ection This is where you s elect t he mode that RNX-Eas y N400 is going t o be use and set it s configurations. You can ch oose AP Router Mode is when you want t o set RNX- EasyN400 as a wireless LAN administrator fo[...]

Wir eless Router RNX-Eas yN400 User M anual 17 Depending on your Network setting, Wizard will show you either one of the pages below, the best detecting option will be selected, please click < Next > unless you wa nt to manually configure yo ur connectin g op tion. 2.3.1.1 DH CP Mode Selection Smart Wizard has detected DHCP client. Click <[...]

Wir eless Router RNX-Eas yN400 User M anual 18 LABEL DESCRIPTION Host Name This is optional. Depending on if your ISP require you to provide this information. Please leave this blank, if you are not sure. MAC address The default value when Click < Clone MAC Address > is set to the WAN ’s physical interface of the broadb and router. Smart Wi[...]

Wir eless Router RNX-Eas yN400 User M anual 19 Please choose your security level, and enter your desired name for your wireless network ( SSID ) and security key ( Key ); Click < Next > to proceed. Depending on how y ou set up RNX-EasyN400, you will see different result pages before you reboot your RNX-EasyN400.[...]

Wir eless Router RNX-Eas yN400 User M anual 20 Below is the example page, if you select the h i ghest security to be your RNX-EasyN4 00 Connecting option. To apply the entire configuration, c l ick < Reboot >. You wi ll see the below cou nt do wn whe n < Reboot > clicked. LABEL DESCRIPTION SSID Enter a descriptive name (up to 32 p rinta[...]

Wir eless Router RNX-Eas yN400 User M anual 21 NOTE: After W ireless settings are applied, yo u need to connect fro m your WLAN client with the security settings you just finished configuring. Remember to write down the type of security & security key you selected. 2.3.2 AP Repeater M ode AP Repeater mode is the R epeater mode which wi ll exten[...]

Wir eless Router RNX-Eas yN400 User M anual 22 You should see the below page, click < Reboot > You will see the count down o f the sy stem rebooting 2.3.3 Connectin g to RNX-E a s yN400 in AP Repeater Mode RNX-EasyN400 will res tart as a repeater now. However , in order to access to the configuration web page of the repea ter, y ou will need [...]

Wir eless Router RNX-Eas yN400 User M anual 23 1. Click on Start > Control Panel > Network and Internet Con nections > Network connections. 2. Righ t-click on the Local Area Connection which represents your net work card and selects Properties. 3. Highli ght Internet Protocol (TCP/IP) and click Properties . 4. Click to use the B secti on l[...]

Wir eless Router RNX-Eas yN400 User M anual 24 192.168.0.X where X is a number between 100 and 200. Make sure that the number you choose is not in use on the networ k. Set Subnet mask as 255.255.255.0. 5. Set Default Gateway the same as the LAN IP address of your router (192 .168 .0.1). 6. After finish, Click < OK >, Then < OK> on below[...]

Wir eless Router RNX-Eas yN400 User M anual 25 8. You will see the configuration homepage u nder “ REPEATER ” m ode now .[...]

Wir eless Router RNX-Eas yN400 User M anual 26 3 Accessing RNX-EasyN400 through Web Browser in Router Mode 1. Make sure your RNX-EasyN400 hardware is properly connected and prepare y our computer or computer network to connect to the RNX-EasyN400 (refer to the Qui ck St ar t Gu ide ) . 2. Launch your web browser. 3. Type " http://192.16 8.0.1 [...]

Wir eless Router RNX-Eas yN400 User M anual 27 3.1 Resetting the RNX-EasyN400 If you forget your password or IP address, or you cannot access the RNX-EasyN400 through Web Bro wser, you will need to us e the < RESET> button at the back of the RNX-EasyN400 to reload the factory-default configuration file. This means tha t y ou will lose all con[...]

Wir eless Router RNX-Eas yN400 User M anual 28 3.2.1 Naviga ting RNX-Easy N400 in AP Router Mode Click on the si de menu selection on System , The picture screen b elow shows the status screen in AP Router Mode . 3.2.1.1 RNX-EasyN 400 Side M enu Desc riptio n Ta ble – A P Rout er Mod e LABEL DESCRIPTION Status This shows the RNX-EasyN400’s gene[...]

Wir eless Router RNX-Eas yN400 User M anual 29 Status This page shows the current Internet connection typ e and status. Dynamic IP This page is only use when your ISP provides you with below information Static IP This page is when your ISP a ssigns you with a fix IP addr ess to connect. PPPoE Th is is used when you set your ISP lo gin account name [...]

Wir eless Router RNX-Eas yN400 User M anual 30 servers/clients in your LAN to handle different service/Internet appli cation type (e.g. Email, FTP, Web server etc.) f rom the Internet. Port tri. In this section you can configure RNX-EasyN400 to support m ultiple connections for these types of applications ALG I n this section, you can let the selec[...]

Wir eless Router RNX-Eas yN400 User M anual 31 3.2.2.1 RNX-EasyN 400 Side M enu Desc ription Table – AP Repeater Mode LABEL DESCRIPTION Status This shows the RNX-EasyN400’s general device, system and interface status information. LAN This is where you can configure LAN IP ad dress, subnet mask, also to enable DHCP server and IP range. Schedule [...]

Wir eless Router RNX-Eas yN400 User M anual 32 web-based management Time The Time Zone allows your router to reference or base its tim e on the settings. DDNS DDNS allows you to map th e static domain name to a dynamic IP address. Power You can enable or disable Saving po wer in WLAN mode Diagnosis This page could let you diag nosis your current ne[...]

Wir eless Router RNX-Eas yN400 User M anual 33 3.3 RNX-EasyN400’s System Page 3.3.1 Status This page allows you to monitor the current status of y our router. Syste m: You can see the Uptime, hardw are information, serial number as well as firmware version i nformation. WAN Settings: This section displays whether the WAN port is connected to a Ca[...]

Wir eless Router RNX-Eas yN400 User M anual 34 3.3.2 LAN The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry level user, try accessing a website from your b rowser. If you can access website without a glitch, just do not change any of these settings. Click <Apply> at the bottom of this screen to save the change[...]

Wir eless Router RNX-Eas yN400 User M anual 35 DHCP Server DHCP Server: This can enable or disable the Dynamic Pool setting. Lease time: This is the lease time of each assigned IP address. Start IP: This is the beginning of the IP pool for DHCP client hosts. End IP: This is the end of the IP pool for DHCP client hosts Domai n nam e: The Domain Name[...]

Wir eless Router RNX-Eas yN400 User M anual 36[...]

Wir eless Router RNX-Eas yN400 User M anual 37 3.3.4 Schedu le This page allows users to set up schedule func tion fo r Firewa ll and Power Saving. Edit schedule op tions to allow con figuration of firewall and power savings services to take effect. Fill in the schedule and select type of service. Click < Apply > to keep the settings. The sch[...]

Wir eless Router RNX-Eas yN400 User M anual 38 3.3.5 L o g Vie w operation event log . This page shows the current system log of the Broadband router. It displays any event occurred after syst em start up. At the bottom of the page, the system log can be saved < Save > to a local file for further processing or the system log can be cleared &l[...]

Wir eless Router RNX-Eas yN400 User M anual 39 3.3.7 Langua ge This Wireless Router support multiple langu age, You can select your desired langu age here.[...]

Wir eless Router RNX-Eas yN400 User M anual 40 3.4 RNX-EasyN400’s Wizard Page Click Wizard to configure the Broadband Router. Setup wizard will be displayed; check that the modem is connected and click < Next >. The details please refer to Setup Wizard at < Page 10 >.[...]

Wir eless Router RNX-Eas yN400 User M anual 41 3.5 RNX-EasyN400’s Internet Page 3.5.1 Status This pa ge shows the curr ent Inte rnet c onnecti on type an d statu s. 3.5.2 Dynamic IP Use the MAC address when registering for Internet service, and do not change it unless required by your ISP . If your ISP used the MAC address of the Ethernet card as[...]

Wir eless Router RNX-Eas yN400 User M anual 42 Host Name: This is option al. Please enter only when your ISP pro vider provides you with this info r mation . MAC address: The default value is set to the WAN’s physical interface of the broadband router. 3.5.3 Stat ic IP If your ISP Provider has assigned a fixed IP address to your internet plan. Pl[...]

Wir eless Router RNX-Eas yN400 User M anual 43 Authentication type: Please use de fault < Auto > to aut o- detec t the best type. Type: Enable the Automatic Conn ection option to automatica lly re-establish the connection when an application atte mpts to access the Internet again. Idle Timeout (Available only under Automatic Connection): This[...]

Wir eless Router RNX-Eas yN400 User M anual 44 3.6 RNX-EasyN400’s Wireless Page 3.6.1 Basic In this wireless basic setting page, you can set your wireless con nection based on Radio, Mode, Band, SSID, and Channel. Radio: You can turn on/off wireless ra dio. If wireless Radio is off, y ou cannot associate with AP through wi reless. Mode: In this d[...]

Wir eless Router RNX-Eas yN400 User M anual 45 2.4 GHz (B): If all of your clients are 802.11b, select this one. 2.4 GHz (N): If all of your c lients a re 802.11 n, selec t this one . 2.4 GHz (B+G): Either 802.11b or 802.11g wireless devices are in y our environment. 2.4 GHz (G): If all of your clients are 802.11g, select this one. 2.4 GHz (B+G+N )[...]

Wir eless Router RNX-Eas yN400 User M anual 46 Enable SSID: We support up to 4 m ultiple SSIDs in this devi ce. Ple ase sel ect how m any SSIDs you would like to use in your n etwo rk environmen t. SSID1~4: ESSID is the name of your wireless network . It might be a unique name to identify this wireless device in the Wireless LAN. It is case sensiti[...]

Wir eless Router RNX-Eas yN400 User M anual 47 3.6.2 WDS with AP Router WDS (Wireless Distribution System), a system that enables the wireless in tercon nection of access point, allows a wireless network to be exten d ed using multiple APs without a wired backbone to link them. Each WDS A P needs same channel an d encryption type settings. MAC addr[...]

Wir eless Router RNX-Eas yN400 User M anual 48 3.6.3 Advan ce d Advanced function allows you to set your RN X-EasyN400 in adv anced wire less options. You should not cha nge these parameters un less you know w hat effect the changes will have on RNX-EasyN400. Fragment Threshold: Th is specifies the maximu m size of a packet d uring the fragmentatio[...]

Wir eless Router RNX-Eas yN400 User M anual 49 Data Rate: The “Data Rate” is the ra te that th is access point uses to trans mit data packets. The access point w ill use the highest possible selected tran smission rate to transmit the data packets. N Data Rate: Th e “N Data Rate” is the ra te that this access point uses to transmit data pac[...]

Wir eless Router RNX-Eas yN400 User M anual 50 SSID Selection: This broadband router support multiple SSID, you could sele ct and set up the wanted SSID. Broadcast SSID: If you enabled “ Broadcast SSID ”, every wireless station located within the cov erage of the RNX-EasyN400 can discover its signal easily. WMM: Enabling Wi-F i Multi-Media can [...]

Wir eless Router RNX-Eas yN400 User M anual 51 WEP Encryption When you select 64-bit or 128-bit WEP key, you have to enter WEP key s to encrypt data. You can generate the key by yourself an d enter it. You can enter four WEP key s and select one of them as a default key. Then AP can receive any packet encry pted by one of the four keys.[...]

Wir eless Router RNX-Eas yN400 User M anual 52 Authentication Ty pe: There are two authentication typ es: "Open System" and "Shared Key" . Both AP and wireless client must be configured with the same authentication ty p e. Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit. The larger the k ey will b[...]

Wir eless Router RNX-Eas yN400 User M anual 53 WPA-Radius Encryption Wi-Fi Protected Access ( WPA ) is an advanced security standard. You can use an external RADIUS server to authen ticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP or CCMP ( AES ) to change the encryption key frequently. Press &[...]

Wir eless Router RNX-Eas yN400 User M anual 54 Enable wireless access control: Enable the wireless access control function . Adding an address into the list Enter the "MAC Address" and "Description" of the wireless station to be added and then click < Add >. The wireless station will now be ad ded into the "MAC Addres[...]

Wir eless Router RNX-Eas yN400 User M anual 55 3.6.6 WPS (Wi-Fi Protected Setup) WPS is the simplest way to establish a connection between the wireless clients and the wireless router. You don’t have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection. You only need to pres[...]

Wir eless Router RNX-Eas yN400 User M anual 56 information when connecting to other WPS-enab led wireless devices. SSID : This is t h e network br oadcas t name (S SID) of R NX-EasyN400. Authentication Mode: It shows the active authentication mode for the wireless connection. Passphrase Key: It shows the p assphrase key that is rando mly generated [...]

Wir eless Router RNX-Eas yN400 User M anual 57 Communication betw e en Wireless clients: A llow Wirele ss Client to co mmunicate wi th other W ireless C lient on s pecifi c SSID. Communication between Wireless clients an d wired clients: Allow Wir eless Client t o communicate with Wired Client on the switch on specific SSID. Or Wireless Client will[...]

Wir eless Router RNX-Eas yN400 User M anual 58 3.7 RNX-EasyN400’s Firewall Pa ge The Broadband router provides ex tensive firewall protection by restricting con nection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to [...]

Wir eless Router RNX-Eas yN400 User M anual 59 server re-directs a particular serv ice/Internet application (e.g. FTP, websites) to a particular LAN client/serv er, whereas DMZ re-directs all packets (regardless of servic es) from your WAN IP address to a particular LAN client/server. Enable DMZ : Enable/disable DMZ LAN IP Address: Fill-in the IP a[...]

Wir eless Router RNX-Eas yN400 User M anual 60 Disc ard Pi ng From W AN: RNX-EasyN400’s WAN port will not respond to any Ping requests Port Scan: Protects RNX-EasyN40 0 from Port Scans. Sync Flood: Protects RNX-EasyN400 from Sync Flood attack. 3.7.4 MAC Filter If you want to restrict users from accessing certain Interne t applications / services [...]

Wir eless Router RNX-Eas yN400 User M anual 61 Fill in “ LAN MAC Address ” and <Description> of the PC that is allowed / denied to access the Internet, and then click <Add> . If you find any typo before adding it and want to retype again, just click <Reset> and the fields will be cleared. Remove PC MAC Address If you want to r[...]

Wir eless Router RNX-Eas yN400 User M anual 62 Deny: If you select “ Deny ” then al l clients will be allowed to access Internet except for the clients in the list below. All ow: If you select “ Allow ” then all clients will be denied to access Internet except for the PC s in the lis t be low. Add PC IP Address You can click <Add> PC [...]

Wir eless Router RNX-Eas yN400 User M anual 63 Fill in “URL/Keyword” and then click <Add> . You can enter the full URL address or the keyword of the web site you want to block. If you happen to make a mistake and want to retype aga in, just click "Res et " and the fie l d will be cleared. Remove URL Keyword If you want to rem ov[...]

Wir eless Router RNX-Eas yN400 User M anual 64 3.8 RNX-EasyN400’s Advanced Page 3.8.1 Network Address Tr anslation (NAT) Network Address Translation (NAT) allows mul tiple users at yo ur local site to access the Internet through a single Public IP Address or multiple Public IP Addresses. NAT provides Firewall protectio n from hacker attacks and h[...]

Wir eless Router RNX-Eas yN400 User M anual 65 Enable Port Mapping: Enable or disable port mapping function. Description: description of this se tting. Local IP: This is the local IP of the server behind the NAT firewall. Protocol: This is the prot ocol t ype to be forwarde d. You c an choo se to f orward “ TCP ” or “ UDP ” packets only, or[...]

Wir eless Router RNX-Eas yN400 User M anual 66 D<D elete S elect ed> . I f you want to remove all Port Mapp ing settings from the table, click <Delete All> button. C lick <Reset> wil l clear your current sele ction s. Click < Apply > at the bottom of the screen to save the above configurations. 3.8.3 Port Fo rwarding (Virtua[...]

Wir eless Router RNX-Eas yN400 User M anual 67 Protocol: Select the port number protocol ty pe (TCP, UDP or both). If you are unsu re, then leave it to the default “both” setting. Public Port enters the service (service/Internet application) port number fro m the Internet that will be re- directed to the above Private IP address host in your LA[...]

Wir eless Router RNX-Eas yN400 User M anual 68 Enable Trigger Port: Enable or disable the Port Trigger function. Trigger Port: This is the outgoing (Outbound) range of port numbers for this particular application. Trigger Type: Select whether the out bound por t prot ocol is “ TCP ”, “ UDP ” or “ BOTH ”. Public Port: Enter the In-coming[...]

Wir eless Router RNX-Eas yN400 User M anual 69 Add Port Triggering Fill in t he " Trigger Port ", " Trigger Type ”, “ Public Port ”, " Public Type ", " Pu blic Port " and " Descripti on " of the setting to be added and then Click <Add> . The Port Triggering setting will be ad ded into the &qu[...]

Wir eless Router RNX-Eas yN400 User M anual 70 3.8.6 UPnP With UPnP, all PCs in you Intranet will discover this router automatically. So, you don’t have to configure your PC and it can easily access the Internet throu gh this router. Enable/Disable UPnP: You can enable or D isable the UPnP feature here. After you enable the UPnP feature, all clie[...]

Wir eless Router RNX-Eas yN400 User M anual 71 This can put the p ackets of specific proto cols in High/Low Qu eue. The packets in High Queue will process first. Unlimited Priority Queue: The LAN IP address will no t be bounded in the QoS limitation. High/Low Priority Queu e: This can put the pack ets in the proto col and port range to High/Low QoS[...]

Wir eless Router RNX-Eas yN400 User M anual 72 This can reserve / limit the thro ughput of specific protocols and port range. Y ou can set the upper bound and Lower bound . T ype: Spec ify the direction of packets. Upload, d own load or both . IP range: Sp ecify the IP address ran ge. Y ou could also fill one IP address Protocol: Specify the packet[...]

Wir eless Router RNX-Eas yN400 User M anual 73 Desti nation LAN IP : Specify the destination LAN IP address of static routing rule. Subnet Mask: Specify the Subnet Mask of static routing rule. Default Gateway: Specify the defau lt gateway of static routing rule. Hops: Specify the Max Hops number of static routing rule. Interface: Specify the Inte r[...]

Wir eless Router RNX-Eas yN400 User M anual 74 You can change the password required to log into the broadband router's system web- based management. By default, the password is: admin. Passwords can co ntain 0 to 12 alphanumeric characters, and are case sensitive. Old Password: Fill in the current password to allow changing to a new password. [...]

Wir eless Router RNX-Eas yN400 User M anual 75 Host Address: This is the IP address of the host in the In ternet that will have management/con figu ration access to the Broad band router from a remote site. If the Host Address is left 0.0.0.0 this means anyone can access RNX-EasyN4 00’s web- based configur ation f rom a rem ote locat ion, provid [...]

Wir eless Router RNX-Eas yN400 User M anual 76 Time Z one: Select the time zone o f the country you are curren tly in. RNX-EasyN4 00 will set its time based on your sele ction. NTP T ime Serve r: RNX-Eas yN400 can set up external NTP Time Server. Daylight Savings: RNX-EasyN400 can also take Daylight Savings into a ccount. If you wish to use this fu[...]

Wir eless Router RNX-Eas yN400 User M anual 77 3.9.3 DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name f rom the DDNS service providers. This router supports DynDNS , TZO and other co mmon DDNS service providers. Enable/Disable DDNS: Enable or disable the DDNS f[...]

Wir eless Router RNX-Eas yN400 User M anual 78 3.9.5 Diagn osis This page could let you diagnosis y our current network status. B y entering any website address, you will know if the internet connection is connected. 3.9.6 Firm ware This page allows you to upgrad e RNX-EasyN400’s firmware. To upgrade the firmware of your Broadban d router, y ou n[...]

Wir eless Router RNX-Eas yN400 User M anual 79 Once you’ve selected the n ew firmware file, cl ick < A pply > at the bottom of the screen to start the upgrade process Caution: • T o upgrade firmware, please make sure the wireless connection is disabled and the computer is connected with a cabl e to the router . • Also make sure the comp[...]

Wir eless Router RNX-Eas yN400 User M anual 80 S tep 2 Log on to the manag ement web page of the AP . By default, the management IP is http://192.168.0.1 , and the user name is “admin”; password is “admin” . Step 3 Click < To ols > and < Firmware >, then Clic k < Browse >. Step 4 Select the la te s t firmware that you sa v[...]

Wir eless Router RNX-Eas yN400 User M anual 81 Step 5 Click < Apply > button. Step 6 Click < OK > button for wr i ting the la test fir mware to your r outer . Step 7 Click < OK > button. 3.9.7 B ac k- up This page allows y ou to save the current rou ter configurations. When y ou save the configurations, you also can re-load the sa[...]

Wir eless Router RNX-Eas yN400 User M anual 82[...]

Wir eless Router RNX-Eas yN400 User M anual 83 4 Repeater Mode Repeater mode has limited se tting s compared to the AP mode. Choose “ Repeater mode ” on the top right corner of the configuration page. System will counting down and restarts automatically. Before your computer connected t o the RNX-EasyN400 in AP Repeater Mode, you will need to m[...]

Wir eless Router RNX-Eas yN400 User M anual 84 2. Right-click on the Local A rea Connection which represents your network card and selects Properties. 3. High light Internet Protocol (TCP/IP) and click Properties . 4. Click to use the B section like below page. You will need to set IP address for default . Example : If R NX-EasyN400 ’s LAN IP add[...]

Wir eless Router RNX-Eas yN400 User M anual 85 5. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). 6. Afte r finish, Click < OK >, Then < OK> on below page 7. Open your web browser and type in 192.168.0.1 on the address bar. At the login, enter your username and password (default username: admin, password[...]

Wir eless Router RNX-Eas yN400 User M anual 86 8. You will see the configuration homepage un der “ Repeater mode ” now. Note: After finishing co figurate y our RNX-Eas yN400 in Repeater mode, please do remember to adjust your computer’s IP address function back to DHCP function.[...]

Wir eless Router RNX-Eas yN400 User M anual 87 4.1 RNX-EasyN400 in Re peater Mode’s System page 4.1.1 Status This page allows you to monitor the current status of y our RNX-EasyN400 in Repeater mode. Syste m: You can see the Uptime, hardw are information, serial number as well as firmware version i nformation. LAN Settings: This section displays [...]

Wir eless Router RNX-Eas yN400 User M anual 88 The LAN Tabs reveals LAN setting s which can be altered at will. If y ou are an entry level user, try accessing a w ebsite fro m your browser. If you can access website withou t a glitch, just do not change any of these settings. Click <Apply> at the bottom of this screen to save the changed con [...]

Wir eless Router RNX-Eas yN400 User M anual 89 The schedule table lists the pre-schedule service-runs. You c an select any of them using the check box. 4.1.4 L og View operation log of RNX-EasyN40 0 . This page shows the current system log of the Broadband router. It displays any event occu rred after system start up. At the bottom o f the page, th[...]

Wir eless Router RNX-Eas yN400 User M anual 90 4.1.5 Monitor Show the network packets histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequen tly . 4.1.6 Langua ge This Wireless Router support m ultiple language of web pages, you could select your nativ e lang uage here.[...]

Wir eless Router RNX-Eas yN400 User M anual 91[...]

Wir eless Router RNX-Eas yN400 User M anual 92 4.2 RNX-EasyN400 in Repeat er Mode’s Wizard page Click Wizard to configure the Broadband Router. Setup wizard will be displayed; check that the modem is connected and click < Next >. The details please refer to Setup Wizard at < Page 10 >. 4.3 RNX-EasyN400 in Repeat er Mode’s Wireless P[...]

Wir eless Router RNX-Eas yN400 User M anual 93 You will see that when add SSID # 2 and SSID #3, you have “Security” in option to set up for your SSID #2 and S SID #3. Radio: This is where you set your RNX-EasyN 400 to broadcast the signal from your wireless router.[...]

Wir eless Router RNX-Eas yN400 User M anual 94 Mode: This is predefined as Repe ater. Band: Depending on the wireless router yo u want to connect to, you will n eed to adjust the band accordingly to the wireless router. Enable SSID #: By default, RNX-EasyN400 h as 1 set of SSID in Repeater mode . However, you can add two more SSIDs for your designa[...]

Wir eless Router RNX-Eas yN400 User M anual 95 Once selected your desired SSID connection, Click < Connect >, then you will see below page popup. Depending on the wireless signal that you want to connect to, RNX-EasyN400 will automatically configures to the current Encryption based on WEP, WPA and WPA2. For example, under the en cryption ty p[...]

Wir eless Router RNX-Eas yN400 User M anual 96 All you have to do is to enter the password of the wireless router you want to co nnect with. Then Click < Apply > You will see the RNX-EasyN400 start countdown and below page appear: Once complete, if successfu l, you should be the below message: Your RNX-EasyN400 is now ready to b roadcast your[...]

Wir eless Router RNX-Eas yN400 User M anual 97 5 PC Network Adapter setup ( Under Windows XP ) • Enter [Start Menu] Æ select [Control panel] Æ select [Network]. • Select [Local Area Connection]) icon=>select [properties][...]

Wir eless Router RNX-Eas yN400 User M anual 98 • Select [Internet Protocol (T CP /IP)] =>Click [Properties]. • Select the [General] tab and Click “a” on both selections. a. RNX-EasyN400 supports [ DHCP ] fu nction, p lease select both [ Obtain an IP address automatically ] and [ Obtain DNS server address automatica lly ].[...]

Wir eless Router RNX-Eas yN400 User M anual 99[...]

Wir eless Router RNX-Eas yN400 User M anual 100 Appendix A – Product Specification Hardware Feature Dimensions 125mm (L) x 98mm (W) x 25mm (H) W AN: One 10/100 Fast E thernet RJ-45 LAN: Four 10/100 Fast Ethern et RJ-45 Reset button Power Jack Physical Interf ace WPS button (W iFi Protected Setup) Power Status W AN (Internet connection) 10/100Mbps[...]

Wir eless Router RNX-Eas yN400 User M anual 101[...]

Wir eless Router RNX-Eas yN400 User M anual 102 Appendix B – Troubleshooting Q: How do I configue to set up Remote M anagement? A: Depending on your internet connect plans, your methods of setting up re mote mana gement wi ll be diff erent . 1. After Login to the RNX-EasyN400 management page, Click 「 Tools 」 , then 「 Admi n 」 . We should [...]

Wir eless Router RNX-Eas yN400 User M anual 103 5. Aft er RNX-Ea syN400 fin ish re set, pl ease Cl ick “ System ”, the n from “ Status ” page below you wi ll see unde r “ WAN Settings ” which shows your External IP address (where has been red circled under “ WAN Settings ”). 6. External IP Address is the IP address which assign by y[...]

Wir eless Router RNX-Eas yN400 User M anual 104 7. We suggest that you change the default login name and password to your desired login name and password which are difficult for others to guess or hack. (Rosewill default login/Password is admin) 8. Use above picture as an example. The External IP address is 10.16.196.62 . The port number that we s [...]

Wir eless Router RNX-Eas yN400 User M anual 105 Q: What is the IP address of my RNX-E asyN400 ? A: The default IP address is 192 .168.0 . 1. However If you changed the IP address and have forgotten it, you might get the IP address of RNX-Easy N400 by lookin g up the IP ad dress of the default ga teway for your computer . T o do this in most W indow[...]

Wir eless Router RNX-Eas yN400 User M anual 106 • If you changed the IP address and have forgott en it, see the troubleshoo ting on how to find the IP address of your RNX-EasyN400. • Make sure your Internet br owser does not block pop -up window s and has JavaScrip ts and Java enabled. • Reset the device to its factory defaults, and try to ac[...]

Wir eless Router RNX-Eas yN400 User M anual 107 with a battery for when power is lost, i.e. T i me W arner Cable Modems, will keep the modem on and connected. Due to the ADSL/Cable modem not assign ing the c orrect DHCP inform ation, t he Rosewill Routers ca n not work correctly and assign a DH CP to the client computers.) • Make sure you entered[...]

Wir eless Router RNX-Eas yN400 User M anual 108 that might be in terfering with the wireless ne twork (for example, microwaves, other wirele ss networ ks, and s o on). • Reboot the RNX-Eas yN400. • Please update the Wi reless Adapter ’ s Firmware of yo ur Notebook and PC to the latest version to ensure the best connection. • Y ou may consid[...]

Wir eless Router RNX-Eas yN400 User M anual 109 Appendix C – FCC Interference Statement Federal Communication Com mission Interfer ence S tatement This equipment has been tested and f ound to comply with the limits for a Class B digital device, pursu ant to Part 15 of the F CC Rules. These limits are designed to provi de reasonable protec tion ag[...]

Wir eless Router RNX-Eas yN400 User M anual 11 0 Italian: In alcuni Paesi si applicano i requisiti per il funzionam e nto in interni -esterni, i requisiti di lic enza e i ca nali consentiti, come descritto si seguito: - In Italia l'uten te finale deve richiedere un a licenza all'Autorità com petente nazionale per il funzionamento in este[...]

Wir eless Router RNX-Eas yN400 User M anual 111 Appendix D – IC Interference Statement Industry Canada statement: This device complies with RSS-210 of the Industry Cana da Rules. Oper ation is subject to t he following two conditions: (1) This device may not cause harm ful interference, and (2) th is device must accep t any interference received [...]