Runco D-73D manuel d'utilisation

3Dimension™ Series D-73d LED Home Theater Projection System I NSTALLATION /O PERATION M ANUAL[...]

[...]

D-73d Series Installation/Operation Manual iii PRE L IMINAR Y RuncoCare™ S tandard Two Year Limited Warranty Congratulations o n your purchase of a Runco® product ! With proper installation, se tup and care, you should enjoy many yea rs of unpara lleled video p erformance. This RuncoCare Standard Limited Warranty is provid ed free of charge by R[...]

iv D-73d Series Installation/Operation Manual PRE L IMINAR Y In the event o f a product de fect, please fo llow the warra nty claim proc edure provided b elow: 1. The Custome r is required to contact a Runco dealer or Runco Te chnical Suppor t via email at sup port@runco.co m or via phone at (toll free) (800) 23-RUNCO (800-237 -8626). If the custom[...]

D-73d Series Installati on/Operation Manual v PRE L IMINAR Y h Expected lam p degradation and normal decrease in lamp output o ver a period of time or a s the lamp is co nsumed i Customer caused defec ts, including b ut not limite d to, scratc hed/defaced /altered plastic s j Failure to follow mainten ance procedu res as outline d in the pro duct?[...]

vi D-73d Series Installation/Operation Manual PRE L IMINAR Y RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LI MITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. 1. RUNC O SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS[...]

D-73d Series Installati on/Operation Manual vii PRE L IMINAR Y Thank you for you r purchase of this qu ality Runco video produ ct! It has been designed to provide you with the qua lity of video that is exp ected in a home theat er. For the be st performan ce, please read this m anual carefully a s it is your gu ide through the menus and operat ion.[...]

viii D-73d Series Instal lation/Operation Manual PRE L IMINAR Y Please read an d make sure you understand the following safety information before using the produc t for viewing 3D content. Provide this infor mation to the e nd users of th is product and ensure that the y understan d it. IMPORTANT HEALTH AN D SAFETY INFORMATION FOR 3D VIEWING: It is[...]

D-73d Series Installati on/Operation Manual ix PRE L IMINAR Y Manufacture r’s Name: Runc o Internation al, LLC Manufacture r’s Address: 119 5 NW Compton Dr ive, Beaverton, OR 97006-19 92 hereby declares that the Produc ts’ Model Numbers: D-73d, D-73d/CineWide and D-73d/Cine Wide with AutoScope conform with th e provisions of: Council Directiv[...]

x D-73d Series Installation/Operation Manual PRE L IMINAR Y NOTE: This equipment has b een tested a nd found to comply with th e limits for a C lass B digital device, pursua nt to Part 15 o f the FCC Rules. T hese limits ar e designed to p rovide reasonab le protection ag ainst harmful inter ference in a resid ential installation. This equipmen t g[...]

D-73d Series Installati on/Operation Manual xi 1 Table of Content s PRE L IMINAR Y RuncoCare™ S tandard Two Year Limited Warran ty ........ ................... ................. ....... iii Important S afety In s truction s ....................... ................ ................ ................ ............. ... vii Compliance Information ....[...]

Table of Contents xii D-73d Series Instal lation/Operation Manual PRE L IMINAR Y Folded Optics ......... ................. ................ ............. ................ ................ ................ 2 8 Audio/Video Sy nchronization Iss ues...... ................ ................ ................ ................ 29 Ventilation ......... .....[...]

Table of Contents D-73d Series Installati on/Operation Manual xiii PRE L IMINAR Y 4. Operation .......... ................ ................ ................ ................ ................ ............. .......... 65 Using the On-Sc reen Menus .................. ................ ................. ................ ................ ... 65 Main Menu[...]

Table of Contents xiv D-73d Series Instal lation/Operation Manual PRE L IMINAR Y Note s :[...]

D-73d Series Installati on/Operation Manual i 1 Li s t of Figure s PRE L IMINAR Y 2-1. D-73d Series LED 3-D Home Theater Projection System B lock Diagram .............. ........ 7 2-2. Standard D-73d Projecto r Functional Co mponents ................. ................ ................ ..... 8 2-3. D-73d Rear Pan el ... ................ ............[...]

List of Figures ii D-73 d Series Installation/Operation Manual PRE L IMINAR Y 3-27. Shasta Ana morphic Lens M ounting Assembly - Exp loded View ...... ................ .......... 57 3-28. Keystone and Pin cushion Disto rtion ......................... ................ ................ ................ 61 3-29. Image Alignmen t Controls .............[...]

D-73d Series Installati on/Operation Manual 1 PRE L IMINAR Y 1.1 About This Manual This Owner’s Ma nual describes ho w to install, set up and operate the Runc o D-73d Series LED 3-D Home Th eater Projection Sys tem. Throughout th is manual, the Runco D-73d Series LED 3-D Home Theat er Projection System are ref erred to collect ively as the “D-7[...]

Introduc tion 2 D-73d Series Installation/Operation Manual PRE L IMINAR Y Graphic Convention s : These sym bols appear in n umerous plac es throughout the manual, to emp hasize points th at you must k eep in mind to a void problems wit h your equipment o r injury: 1.2 Using This Manual Use the following ta ble to locate the spec if ic information y[...]

Introd uction D-73d Series Installati on/Operation Manual 3 PRE L IMINAR Y 1.3 Description, Features and Benefits Runco’s exclusive ne w D-73d Series LED 3-D Home Theater Projection System integrates 3D visua lization tech nology that is based o n the science of h ow the human e ye and brain pr ocess actual d epth and dim ension in real life , Ru[...]

Introduc tion 4 D-73d Series Installation/Operation Manual PRE L IMINAR Y With Runco CineWid e, the projectio n system is able t o use the full p ixel array, thereb y producing a 2 .35:1 image with enhanced reso lution and in creased brig htness. No resolution o r image area is lost to those black bars th at contain no picture infor mation. CineWid[...]

Introd uction D-73d Series Installati on/Operation Manual 5 PRE L IMINAR Y Parts List Your D-73d is ship ped with the f ollowing items. If an y items are missin g or damaged, please contac t your Runco de aler or Runco Cu stomer Service at (800) 23-R UNCO. • D-73d Series LED 3-D Home Thea ter Projection System: •P r o j e c t o r • Two (2), D[...]

Introduc tion 6 D-73d Series Installation/Operation Manual PRE L IMINAR Y Note s :[...]

D-73d Series Installati on/Operation Manual 7 PRE L IMINAR Y The D-73d Se ries LED 3-D Hom e Theater Proje ction System consist s of the following component s: • The projector , consisting of two discret e LED optical engines stac ked one on top of the other to pr ovide either tw o-dimensional (2D ) or three-d imensional (3D) c ontent. • A Prim[...]

System Overview 8 D-73d Series Installation/Operation Manual PRE L IMINAR Y 2.1 Projector The standard D-73d pro jector, shown Figure 2- 2, consists o f two discre te LED optica l engines stacke d one on to p of the oth er to provide e ither three-dime nsional (3D) or two-dimensional (2D) content. For 3D cont ent, each eng ine produce s the image f[...]

System Overview D-73d Series Installati on/Operation Manual 9 PRE L IMINAR Y • LEN S LOCK The screw to the right of the lens activates the lens lock, whic h freezes the zoom and lens shift se ttings to keep th e projector images a ligned ov er time. When shipped fr om Runco, the lenses are u nlocked. To lo ck the lens p osition, use t he same 5.0[...]

System Overview 10 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 1. POWER INPUT (Left-Eye E ngine – 100 to 240 V AC) Connect the left-eye optical engin e to power here. 2. DHD INPUT (Left-Eye Engine) An HDCP-compliant dig ital video input for connecting the HDMI Out (T o Di s play) from the Prim ary DHD Controlle r. 3. R S -232C INPU[...]

System Overview D-73d Series Installati on/Operation Manual 11 PRE L IMINAR Y 2.2 Primary DHD Controller The Primary DHD Controller provides a video signal an d OSD menu to t he left-eye optica l engine of the projector. It co ntrols the ot her D-73d system components in response to user input via the follo wing interfaces: • Front-pan el keypad [...]

System Overview 12 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 6. DOWN BUTTON Use to direct-se lect aspect ra tios or move th e menu cursor down in the OSD. When no menu is p resent on-scree n, this butt on toggles th rough aspect r atios in the following orde r: 16:9 - 4:3 - Letterbo x - VirtualWide - Cinema - Virtu al Cinema - Nati[...]

System Overview D-73d Series Installati on/Operation Manual 13 PRE L IMINAR Y 3. U S B A standard, USB Seri es “B” connection to a pe rsonal computer, for performing software upgr ades and other service pr ocedures. 4. R S -232 (T o Acce ss ory Box) A male, 9-pin D-su b connecto r for interfacin g with the Seco ndary DHD Contro ller. (Use a “[...]

System Overview 14 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 2.3 Secondary DHD Controller The Secondary DHD Controller provide s a video signal and O SD menu to th e right-eye optical engin e of the projector . Figure 2-6 sho ws the Secondar y DHD Controlle r front and re ar panel. Figure 2-6. S econdary DHD Co ntroller Front and R[...]

System Overview D-73d Series Installati on/Operation Manual 15 PRE L IMINAR Y 7. HD2 Input (5 x Analog BNC s ) Connect the HD 2 input to t he Right Analog ou tput on the 3D imension Proc essor. The HD 1 input is not used with the D- 73d. Connect your Compone nt/RGBHV sources to the 3Dimension Processor. 8. Vid eo 1 In p ut Connect the Video 1 input[...]

System Overview 16 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 1. RUNCO ICON Lights blue to indicate tha t the 3Dime nsion Processor is o n or poweri ng up. 2. MAIN POWER S WITCH Disconnects or applies power to the 3Dimensio n Processor. 3. POWER INPUT (100 to 240 V AC) Connect the 3Dimension Process or to power here . 4. HDMI 1 / HD[...]

System Overview D-73d Series Installati on/Operation Manual 17 PRE L IMINAR Y 2.5 DHD Controller Remote Control Unit Figure 2-8 shows the D-73 d remote control, and the paragraphs th at follow describe its functionalit y. Figure 2-8. DHD Co ntroller Remote Contro l ON ISF NT VID 1 VID 2 HD 1 HD 2 VID 3 COMP ISF DA Y CUST 1 CUST 2 OFF RA TIO RA TIO [...]

System Overview 18 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 1. IR OUTPUT INDICA TOR Lights when a button is pressed to indicat e that an IR signal is being transmit ted. 2. LIGHT Press to illumin ate the buttons. 3. ON / OFF Press to turn the DHD Contro ller and projec tor on or o ff. 4. ENTER Press to select a h ighlighted m enu [...]

System Overview D-73d Series Installati on/Operation Manual 19 PRE L IMINAR Y 10. HD 1 (4) / HD 2 (5) Press to select a HD (RGBHV or YPbPr c omponent) input or to ent er the numeri c character “4” or “5.” 11. COMP (Component) (6) Press to select t he Component video input as the source or t o enter the nu meric character “6. ” 12. HDMI [...]

System Overview 20 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Note s :[...]

D-73d Series Installati on/Operation Manual 21 PRE L IMINAR Y 3.1 Remote Control To install batteries in the remote co ntrol: 1. Press down the tab on the cover an d pull the cove r in the direct ion of the arrow. 2. Insert the includ ed batteries. Ensu re that the polaritie s correctly match t he and markings inside the bat tery compartm ent. 3. I[...]

Installation 22 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 3.2 Quick Setup Table 3-1 gives a quic k overview of the D-73d installation process. The sections following this one prov ide detail ed instru ctions. Table 3-1. In s tallation Overview S tep Procedure For Detail s , Refer to page... 1 Choose a location for the projector 23 [...]

Installation D-73d Series Installati on/Operation Manual 23 PRE L IMINAR Y 3.3 Installation Considerations Proper installation of you r projector will ensure the qualit y of your display. Wh ether you are installing a pr ojector tempor arily or per manently, you should take th e following into account to ensure your p rojector perfo rms optimally. [...]

Installation 24 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Choosing A Screen Runco 3Dim ension Series p rojectors pr oduce exception al 3D and 2D c ontent. Becaus e it is estimated t hat 2D content st ill comprises more t han 90 percen t of the materi al viewed in home theate rs and pr ivate cinema s, the proje ction scree n is a si[...]

Installation D-73d Series Installati on/Operation Manual 25 PRE L IMINAR Y Figure 3-1. E s timating Throw Di s tance Table 3-3 lists th e available le ns options for th e D-73d an d their associat ed throw ratios. Table 3-3. D-73d Len s Option s and Throw Ratio s (Note) Projector Model Throw Ratio with Primary Len s Only Throw Range in inche s , wi[...]

Installation 26 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Vertical and Hori zontal Position Proper placem ent of the project or relative to t he screen will yield a rectangular, perfectly-cen tered image that completely f ills the screen. Ideally, the pro jector should be positioned perpendicular t o the screen and in such a way th[...]

Installation D-73d Series Installati on/Operation Manual 27 PRE L IMINAR Y Figure 3-4. Horizontal Le n s S hift (EXAMPLE ONLY) 0% Screen Center 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) Screen Width (W) Note: This is a general example of lens shift. Lenses vary in thei r shift capabilitie s. No particular lens or projector is u[...]

Installation 28 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Table 3-4 lists the usable le ns shift ranges for each ava ilable D-73d lens, a s percentage s and absolu te measurem ents with a 96 x 54 inch (1.78:1) scre en. Folded Optics In rear screen applications wher e space behind the projector is lim ited, one or m irrors may be us[...]

Installation D-73d Series Installati on/Operation Manual 29 PRE L IMINAR Y Audio/Video Synchronization Issues Due to its extraor dinarily high level of video processing perfor mance, the DHD Control ler may distribute video signals with a perceptible level of audio laten cy. In order to easily solve this issue, Run co recommen ds using the DHD Cont[...]

Installation 30 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Ventilation If you are moun ting the D-73d in an enclosure, leave at least 3 inches (76.2 mm) of space on the left and right sides betw een it and surroun ding objects, as show n in Figure 3-6. This allows heat to disperse, mai ntaining the proper operat ing temperatur e. Fi[...]

Installation D-73d Series Installati on/Operation Manual 31 PRE L IMINAR Y 3.4 Installing the Optional Anamorphic Lens Mount If you are installing a standard D-73d (without an anam orphic lens), skip this step and proceed with Mounting the D-73d (page 36 ). If you are installing a D-73d/CineWide, pro ceed with Installing the Fixed CineWide Base Pla[...]

Installation 32 D-73d Series Installation/Operation Manu al PRE L IMINAR Y In s talling the Len s Motor: 1. Position the Au toScope lens m otor as shown in Figure 3 -7. 2. Line up the mountin g holes on the lens mot or housing with those on the underside of the projector . 3. Secure the motor to the p rojector wi th the eight (8) supplied M6 x 12mm[...]

Installation D-73d Series Installati on/Operation Manual 33 PRE L IMINAR Y Connecting the Auto S co pe Len s Motor to the Projector: Connect the AutoScope lens transport moto r to the 12-volt trigger ou tput on the projector (labeled CINEWIDE/AUTO S CO PE ), as shown in Figure 3-8 . Figure 3-8. Connecting th e Auto S cope Len s Motor to the Project[...]

Installation 34 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Installing the Fixed CineWide Base Plate (D-73d/CineWide) D-73d/CineWide with Whitney Anamorphic Len s : Fig ure 3-9 shows the Whitney anamorphic lens base plate assem bly for a D-73d/CineWid e. Figure 3-9. D-73d/CineWid e with Whitney Anamorphic Len s Ba s e Plate - Explode[...]

Installation D-73d Series Installati on/Operation Manual 35 PRE L IMINAR Y D-73d/CineWide with S ha s ta Anamorphic Len s : Figur e 3-10 shows the Sha sta anamorphic lens base plate assembly for a D-73d/Cine Wide. Figure 3-10. D- 73d/CineWide with S ha s ta Anamorphic Len s Ba s e Plate - Exploded View To install the Shasta anamorphic lens base pla[...]

Installation 36 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 3.5 Mounting the D-73d There are se veral method s for mounting the projector . Depending on your chosen installation, one method may b e more suit able than anoth er. Floor Mounting (Upright) In typical front and rear scre en installations, the p rojector can be m ounted to[...]

Installation D-73d Series Installati on/Operation Manual 37 PRE L IMINAR Y 3.6 Mounting the DHD Controllers and 3Dimension Processor The DHD Contr oller units and 3Dimen sion Processor can be placed on any flat, stable surface such a s a shelf or table, or they can be rack-mounte d using the supp lied mounting hard ware. Place the se compone nts in[...]

Installation 38 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 3.7 System Interconnections Proceed as fo llows to connect the D-73d system components to each other and to AC power. When connec ting your equipm ent: • Turn off all eq uipment before making any c onnections. • Use the cor rect signal cables for each sourc e. • For be[...]

Installation D-73d Series Installati on/Operation Manual 39 PRE L IMINAR Y Figure 3-14 sh ows how to c onnect the Prima ry and Seco ndary DHD Con trollers to the projector. Figure 3-1 4. Connect ing the Prim ary and S econdary DHD Controller s to the Projector PRIMARY PRIMARY SECONDARY SECONDARY ABCDE H DHD4 Secondary Pr R Y G Pb B Pr R HV HD2 T Vi[...]

Installation 40 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Connecting the Primary and Secondary DHD Controllers to Each Other and to the 3Dimension Processo r Figure 3-15 shows the connectio ns between the 3 Dimension Processor an d Primary and Secondary DHD Cont rollers. Figure 3-15. DHD Controller /3Dimen s ion Proce ss or Interco[...]

Installation D-73d Series Installati on/Operation Manual 41 PRE L IMINAR Y To make these conn ections easier, the rear-pa nel connectors on the 3Dimension Processor and DH D Controllers ar e identified and colo r-coded as follows: Digital Video Connection (G): Connect the HDMI 1 input on the Primary DHD Controller to the Left HDM I output on th e 3[...]

Installation 42 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Connecting an Audio Processor or Secondar y Display Device to the Primary DHD Controller (Optional) The Primary DHD Controller pr ovides a secon d HDMI output (labeled HDMI Out (Audio Only) ) for connec tion to an audio receiver/switchi ng system or sec ondary display de vic[...]

Installation D-73d Series Installati on/Operation Manual 43 PRE L IMINAR Y Additional Connections to the Primary DHD Controller (Optional) The Primary DHD Controller pro vides the follow ing interface s to extern al equipment that allow it to control or be contro lled by that equipment : • An RS-232 interface to a PC or contr ol/automa tion syste[...]

Installation 44 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Connecting 12-volt Trigger Output s to External Equipment: Connec t any 12-volt trigger-act ivated equipme nt (such as re tractable scre ens or screen m asks) to the 1 2-volt trigger outputs on the Primar y DHD Controller; see Fig ure 3-18. Figure 3-18. Connecting 12-volt Tr[...]

Installation D-73d Series Installati on/Operation Manual 45 PRE L IMINAR Y Ethernet Network Connection: Use a standard, Cate gory 5 netw ork cable w ith an RJ-45 plug to c onnect a ne twork hub, r outer or ga teway to the Ethernet po rt on the Primary DHD Controller ; see Figure 3-20 . For more in formation abou t configuring and using this conn ec[...]

Installation 46 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Connecting Source Componen ts to the 3Dimension Proces sor Connect your video sources to the 3Dime nsion Processor as shown and descr ibed in the sections th at follow. HDMI S ource Connection s : See Figure 3-21. Figure 3-21. HDMI S ource Conn ection s ➤ Use the HDMI inpu[...]

Installation D-73d Series Installati on/Operation Manual 47 PRE L IMINAR Y Compone nt Video S ource Connection s : Connect your componen t video sources to the HD1, HD2 a nd/or Compo nent/SCART inputs as shown in Figur e 3-22. Figure 3-22. Compone nt Video S ource Connection s HD 1 Y G Pb B Pr R HV Y G Pb B Pr R HV I N A BCDE FG Component/SCART Vid[...]

Installation 48 D-73d Series Installation/Operation Manu al PRE L IMINAR Y RGBHV S ource Connection s : Connect personal computer s and/or othe r RGB sources to the HD1 and/or HD2 inputs as sh own in Figure 3-23. Figure 3-23. RGBHV S ource Conne ction s HD1 HD2 Y G Pb B Pr R HV Y G Pb B Pr R HV IN P DE FG DE FG USB IR or Computer R G B Camcorder Gr[...]

Installation D-73d Series Installati on/Operation Manual 49 PRE L IMINAR Y S CART RGB S S ource Connection s : Connect the gre en, blue a nd red outp uts from your SCART source to the Compo nent/SCART input on the 3Dimension Pr ocessor. Connect the sync output from your SCART sou rce to the Vi d eo 1 input on the 3Dimension Pr ocessor. See F igure [...]

Installation 50 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Compo s ite S ource Connection s : Se e Figure 3-25. Figure 3-25. Co mpo s ite Video S ource Connection s Connecting to AC Power Plug the female end of a p ower cord int o each AC re ceptacle on t he rear of the D-73d (AC 100V ~ 240V ); see Figure 2- 3. Then, co nnect the ot[...]

Installation D-73d Series Installati on/Operation Manual 51 PRE L IMINAR Y 3.8 Power-Up Sequence and Optical Alignment Procedure At this point you are read y to perform th e in itial power-up sequence and optical alignmen t procedure, which is summarize d in Table 3 -6 and descr ibed in detail in the sections tha t follow. This procedure assumes th[...]

Installation 52 D-73d Series Installation/Operation Manu al PRE L IMINAR Y DHD 1. Select Calibration -> Adju s tment Mo de and set it to S econdary . 2. Select S ervice -> T e s tV i d e o and choose S econdary Alignment . Projector (Align S econdary/Right Image with S creen) 1. Align the image to the screen by adjusting the Right (bottom) pr[...]

Installation D-73d Series Installati on/Operation Manual 53 PRE L IMINAR Y Anamorphic Lens Installation (D-73d/Cin eWide with AutoScope Only) If you are installing a D-73d/CineWide with Aut oScope, install the anamorphic lense s as described in t he section ent itled D-73d/CineWide or D-73d/CineWide with AutoScope - Shasta Anamorph ic Lens Installa[...]

Installation 54 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 4. Press the ON button on the re mote control (o r the ON/ S TA N D B Y ( ) button on the Primary DHD Cont roller front pan el) to turn on th e system. The vacuum fluoresce nt display on the Primary DHD Cont roller fr ont panel briefly d isp lays “Initializing System,” f[...]

Installation D-73d Series Installati on/Operation Manual 55 PRE L IMINAR Y 8. Focu s Left (T op) Primary Len s : To foc us the projecte d image, gras p the lens by the outer ring and rotate it. 9. Adju s t Zoom on Left (T op) Primary Len s : To make the projected imag e smaller (zoom out) or larger (zoom in), move the zoo m tab in the approp riate [...]

Installation 56 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Adjusting the Picture Orientation By default, t he D-73d is conf igured for a “floor/fro nt” installation, in which th e projector is installed upright and in front of the screen . If it is instal led behind the screen an d/or mounted on a ceiling, you must change the pi[...]

Installation D-73d Series Installati on/Operation Manual 57 PRE L IMINAR Y 1. Remove the two Yaw /X Adjust ment Lev ers and Washer s ( 5 ) from the bottom of the Anamorphic Le ns Holder ( 2 ). 2. Place the Anamo rphic Len s Holder on top of (or unde r, if the proje ctor is inverted) t he CineWide Base Pla te. Position the bracket so that the slots [...]

Installation 58 D-73d Series Installation/Operation Manu al PRE L IMINAR Y 1. Remove the t wo Yaw/X Adjustme nt Levers and Washers ( 7 ) from th e bottom of the Anamorphic Lens Hold er ( 2 ). 2. Place the Anamorphic Lens Holder on top of (or under, if th e projector is inve rted) the AutoScope Le ns Motor Carriage Plate or CineWid e Base Plate. Pos[...]

Installation D-73d Series Installati on/Operation Manual 59 PRE L IMINAR Y • Vertical Po s ition (Y-adju s t): Loos en the Height/P itch Adjustment Knobs (Whitney anamorphic le ns; see Figu re 3-26) or B utton-hea d Height Adjustmen t Screws (Shasta anamorphic lens; see Fi gure 3-27) o n either side o f the lens. Then, slowly m ove the anamorphic[...]

Installation 60 D-73d Series Installation/Operation Manu al PRE L IMINAR Y •A d j u s ting the Yaw: Loosen the Ya w/X-Adjustment Levers to al low the lens t o pivot freely from sid e to side. The n, angle the le ns to even ou t any left-right pincushion distortion: Once the pr oper lens angl e has been se t, firmly tighten the Yaw/X-Adjus tment L[...]

Installation D-73d Series Installati on/Operation Manual 61 PRE L IMINAR Y Adjusting the Image Geometry Projector and /or screen p lacement — a mong other things — c an cause geom etric distortion in th e projected ima ge. To correct this, the DHD Co ntroller provides precise, nine-point control over the proje cted image geometr y. Use these co[...]

Installation 62 D-73d Series Installation/Operation Manu al PRE L IMINAR Y “Keystoning” usu ally occurs when the pro jector is tilted relative to the screen. “Pincushion ” distortion can so metimes occu r if the thr ow distance is ve ry short and/o r the projector is equipped with a n anamorph ic lens. Corner/Midpoint Alignment — 16:9 A s[...]

Installation D-73d Series Installati on/Operation Manual 63 PRE L IMINAR Y Corner/Midpoint Alignment — Cinema (2.35:1) A s pect Ratio: 1. Select the Cinema aspect rat io using eithe r the DHD Contr oller remote co ntrol unit (see Figure 2 -8) or the OSD menu (p ress MENU , then select A s pect Ratio -> Cinema ). This should move the an amorphi[...]

Installation 64 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Note s :[...]

D-73d Series Installati on/Operation Manual 65 PRE L IMINAR Y 4.1 Using the On-Screen Menus To display the Main Menu, press the MENU butt on on the re mote control or Primary DHD Controller f ront panel. To select a m enu item, use th e an d buttons on the remote contr ol or Primary DHD Controller fron t panel to high light it. Then , to confirm yo[...]

Operation 66 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Figure 4-1. D-73d O S D Menu S tructur e (continued) S ervice Test Vide o Color Bars 1 Color Bars 2 Focus Grey Bars Primary / Secon dary / Dual Alignment Input Names Rename/Restore Display Device - Configure Picture Orient ation Auto, Floor Front , Ceili ng Front, Floor Rear or[...]

Operation D-73d Series Installati on/Operation Manual 67 PRE L IMINAR Y Main Menu The Main Menu is the startin g point fo r accessing all DHD Controller functions. (You must enter a passcode to access the Calibr ation and Se rvice menus.) Input Source From the M ain Menu, selec t Input Sou rce to choose a video signal so urce. The active so urce is[...]

Operation 68 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Table 4-1. A s pect Ratio S etting s A s pect Ratio Remote Control Key De s cription 16:9 16:9 Select 1 6:9 to vie w 16:9 DV Ds and HDTV programs in their native aspec t ratio. 4:3 images are stretched horizontally to fit a 16:9 scre en. 4:3 4:3 Standard 4:3 scales the input si[...]

Operation D-73d Series Installati on/Operation Manual 69 PRE L IMINAR Y Cinema CINEMA Select Cinema to view 2.35 source material in its native aspect ratio. With a 16:9 screen and a standard D-73d (without an anamorphic lens), the upper and lower portions of the screen are masked, but the geometry of the active image area is unchanged. With a 2.35:[...]

Operation 70 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Screen The Screen Menu allows you to recall multiple sets of stored values for ce rtain controls (Output Shift an d Image Alignmen t, to name t wo) that are saved for eac h aspect ratio. Such settings are al so saved “per screen.” To recall the Outp ut Shift and Image Align[...]

Operation D-73d Series Installati on/Operation Manual 71 PRE L IMINAR Y Brightne ss : On your external test pa ttern source, se lect a PLUG E pattern. (PLUG E is an acronym for “Picture Line-Up Generation Equipme nt.”) Figure 4-2 shows a typical PLUG E pattern. Figure 4-2. Typical PLUGE Pattern for Adju s ting Brightne ss PLUGE patterns va ry b[...]

Operation 72 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Color S aturation: On your e xternal test patt ern source, se lect a color bar pattern like the one shown in F igure 4-4. Figure 4-4. Typical Color Bar Pattern for Adju s ting Color S aturation and Tint 1. Press the MENU button on the remote control or DHD Controller front pane[...]

Operation D-73d Series Installati on/Operation Manual 73 PRE L IMINAR Y 11.Adjust the color sa turation level until the out ermost (gray and bl ue) color bars appear to be a single shade of bl ue: Tint: Tint or “hue” is essentially the r atio of red t o green in th e color por tion of the im age. When tint is dec reased, the image appears redde[...]

Operation 74 D-73d Series Installation/Operation Manu al PRE L IMINAR Y S harpne ss : “Sharpness” is th e amount of high-frequen cy detail in the image . To adjust sharpness, select Shar pness from the Pictur e menu and press ENTER . On your external test pattern source, sele ct a pattern like the one show n in Figur e 4-5. Adjust as ne eded, l[...]

Operation D-73d Series Installati on/Operation Manual 75 PRE L IMINAR Y Height: Select Height from the Input Position menu to change the p rojected image height. Pres s to increa se the height; press to decrease it. Over s can/Over s can Mode: Overscan pushes the outside edge of th e active pictur e area of the video signal out beyond the edge of t[...]

Operation 76 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Pha s e (RGB, Comp onent or S CART s ource s ): This control adjusts the phase of the pixel sampling clock relative to the inc oming signal. Adjust the phase wh en an RGB, Component or SCART image st ill shows shimmer or “noise” after Tracking has been optimized. For best r[...]

Operation D-73d Series Installati on/Operation Manual 77 PRE L IMINAR Y You should save ch anges to any of the follo wing settings to a pres et; otherwise they will be lost when a new input sour ce or resolution is selected: • Brightness •C o n t r a s t • Color saturation •T i n t • Sharpness •G a m m a • Lamp Settings • Color temp[...]

Operation 78 D-73d Series Installation/Operation Manu al PRE L IMINAR Y •C h o o s e Frame Packing to have the 3Dimension Proc essor decode frame packed data into le ft and right e ye data. In th is mode, the DHD C ontrollers do not perform a ny 3D processing. Rever s e Eye s : By default, the Prima ry and Secondar y DHD Controllers are d edicate[...]

Operation D-73d Series Installati on/Operation Manual 79 PRE L IMINAR Y Calibration Use the Calibrat ion menu to per form advanced picture quality ad justments. Th i s menu s hould be u s ed by I S F-certified technician s only . To recall the ISF N ight or ISF Day se ttings, select “ISF N ight” or “ISF Day” fr om the Memory Presets m enu ([...]

Operation 80 D-73d Series Installation/Operation Manu al PRE L IMINAR Y • Color Temp: Select Color Temp from the Display Colo r - Common Settings menu to adjust the co lor temper ature. Colo r temperat ure establishes t he “color of g ray” by adjusting th e 75% white po int to various color points . What are “color point s ? ” A “color [...]

Operation D-73d Series Installati on/Operation Manual 81 PRE L IMINAR Y • Color Gamut: Select Color Gamut from the Display Color - Common Settings men u to select a color gam ut (range) that may be diffe rent from the defaul t color gamut. Each setting de fines the prec ise hue of each primary (red, g reen and b lue) and secondary (yellow, cyan a[...]

Operation 82 D-73d Series Installation/Operation Manu al PRE L IMINAR Y • Hue/ S aturation/Level: PCE provides the ability to defi ne a custom color gamut in terms of prima ry (red, gree n and blue) a nd secondary (ye llow, cyan and magen ta) color hues, sa turation and leve l (brightness). Each control op erates only on the color specified. Surr[...]

Operation D-73d Series Installati on/Operation Manual 83 PRE L IMINAR Y Di s play Color - Projector S etting s : These settings are also saved independ ently for each input an d display mode. • S atCo (BrilliantColor™): Select SatCo (BrilliantColor™ ) from the Display Color - Projector Settings menu to enable (On) or disable (Off) BrilliantCo[...]

Operation 84 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Copy/Pa s te - Memory Pre s et: You can copy and paste setting s from one memory preset to anothe r. This gives you a convenient sta rting point for creating a new preset based on an existing one , to make th e calibration pro cess less time-cons uming. For example, you can use[...]

Operation D-73d Series Installati on/Operation Manual 85 PRE L IMINAR Y •A s pect Ratio - Pa s te S etting s : To apply the Output Shift a nd Image Alignm ent settings on the clipboard to a different a spect ratio an d/or screen , do either of the following: • Switch to another aspe ct ratio (for example, from 16:9 to Cinem a). • Switch from [...]

Operation 86 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Service Use the Service m enu to access advanced projecto r configuration settings. Thi s menu s hould be u s ed by I S F-certified technician s on ly . Te s t Video: Select Test Video from th e Service Menu to access th e internal test p atterns on the DHD Con troller. Table 4[...]

Operation D-73d Series Installati on/Operation Manual 87 PRE L IMINAR Y Press MENU to exit test pattern mode. Input Name s : You can give each input a descriptive name . For example, y ou may want to change th e default input na me to the type of sour ce component connected t o it: “VCR,” “DVD,” “Laptop” et cet era. Input na mes can be [...]

Operation 88 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Network: The options in the Network m enu allow you to configure the ne twork communication fea tures. • IP Config uration : Select IP Configur ation from the N etwork menu to either set the IP address, subnet mask and d efault gateway of the DHD Contro ller manually or obtai[...]

Operation D-73d Series Installati on/Operation Manual 89 PRE L IMINAR Y If you prefer to do this manually, set it to Off. The DHD Controller w ill ask if you want to perform th e upgrade t he next time it is power-cycled. • Check For New Fi rmware: To have the DHD Controller check for new firmw are on demand (an d perform an upgrade if it fin ds [...]

Operation 90 D-73d Series Installation/Operation Manu al PRE L IMINAR Y • Error Notification : To have th e DHD Controller se nd a message to the destinatio n e-mail address whe n a “DHD Error” or “Display Err or” occurs, sele ct Error Notification from the E-Mail No tification m enu and set it to On . • Error Notif ication to Runco : T[...]

Operation D-73d Series Installati on/Operation Manual 91 PRE L IMINAR Y • Remote Network Control: Select Remote Network Cont r ol from the Networ k menu to enable or disa ble control of the DHD Controller via an IP connec tion (typically usin g a web browser) . Set it to On to allow all incoming remote network connectivity. Set it to Off to disab[...]

Operation 92 D-73d Series Installation/Operation Manu al PRE L IMINAR Y •O S D Me ss age s : When you select a new aspect ratio, inpu t source or memory pres et, the DHD Contro ller briefly displays an on-screen messag e confirming you r new selection. T o prevent the d isplay of these m essages, select OSD Messages fro m the Miscellaneou s menu [...]

Operation D-73d Series Installati on/Operation Manual 93 PRE L IMINAR Y S ync Thre s hold: Select Sync Threshold to adjust the threshold at which negative puls es on the com ponent video green/lum a channel are interpreted to be sync pu lses. Sync Threshold a djustment is occasionally nec essary when a DVD p layer or HDTV sourc e signal drops “be[...]

Operation 94 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Front Panel Brightne ss : Select Front Pan el Brightness from the Servic e menu to adjust the brightness o f the front-panel LED and LCD status in dicators. • Logo LED: Select Logo LED fr om the Front Panel Brightness m enu to adjust the brightness of the large, illu minated [...]

Operation D-73d Series Installati on/Operation Manual 95 PRE L IMINAR Y S tandby Mode: Select Standby Mode from th e Service menu to control the DHD Controller’s power mana gement feat ure. •C h o o s e Low Power (the default setting) to have the DHD Controller shut down completely whe n it is turned o ff. This conser ves power bu t increases t[...]

Operation 96 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Note s :[...]

D-73d Series Installati on/Operation Manual 97 PRE L IMINAR Y Maintenance The D-73d Series LED 3-D Home Theat er Projection System does not require any r outine maintenance to speak of, w ith the ex ception of sw itching, c leaning or r eplacing the polarizing filters in front of each p rimary lens. Ther e are no ot her user-serviceab le or -replac[...]

Maintenance and Troublesho oting 98 D-73d Series Installation/Operation Manu al PRE L IMINAR Y Identifying the Left and Right Polarizer s : Although the left and right polarizers have very different optical charac teristics, they ap pear to be identical. As a re sult, once you remove them from the pro jector it may b e difficult to tell them ap art[...]

Maintenance and Troubleshooting D-73d Series Installati on/Operation Manual 99 PRE L IMINAR Y The “right-eye” optical engine does not turn o n or respond to user commands. The vacuum fluorescent display on the Pri- mary DHD Controller front panel displays the following message: Secondary Display Error Communication Failure • The serial connec[...]

Maintenance and Troublesho oting 100 D-73d Series Installation/Operation Manual PRE L IMINAR Y Colors in the ima ge are swapped; for example, reds appear blue or vi ce versa. • The Red/Pr, Green/Y or Blue/Pb outputs from the source are connected to the wrong inputs on the 3Dimension Processor. • Ensure that the source outputs are connected to t[...]

Maintenance and Troubleshooting D-73d Series Installati on/Operation Manual 101 PRE L IMINAR Y AutoScope lens motor doesn’t work. • The motor is n ot plugged in or the AC outlet is not active. • The motor is not connected to the trigger outp ut on the projector. • Ensure that t he motor is plugged in and that the AC outlet is active. • Ch[...]

Maintenance and Troublesho oting 102 D-73d Series Installation/Operation Manual PRE L IMINAR Y Note s :[...]

103 D-73d Series Installation/Operation Manu al PRE L IMINAR Y In addition to using the DHD Cont roller front-panel keyp ad or remote control unit, the re are three met hods of controlling the D-7 3d and DHD Controller extern ally: • Using a serial (R S-232) link to sen d ASC II commands and receive responses to those commands. • Using discrete[...]

External Control 104 D-73d Series Installation/Operation Manual PRE L IMINAR Y Table 6-1 lists the RS-232 comman d set. The “Param eter (min/m ax)” column shows the valid parameter ranges, or “NA” for comman ds that take no paramet ers. When you enter a valid comma nd, the DHD Controller execute s it and acknowledges it with a plus sign on [...]

External Control D-73d Series Installati on/Operation Manual 105 PRE L IMINAR Y A s pect Ratio Command s 16:9 NA YES Selects the 16:9 aspect ratio 4:3 NA YES Selects the 4:3 aspect ratio ASPECT? NA NA Returns cu rrent aspect ratio CINEMA NA YES Selects the Cinema aspect ratio LETTERBOX NA YES Selects the Letterbox aspect ratio NATIVE NA YES Selects[...]

External Control 106 D-73d Series Installation/Operation Manual PRE L IMINAR Y Image Pre s et Command s CUSTOM1 NA YES Loads “Custom 1” image preset CUSTOM2 NA YES Loads “Custom 2” image preset DAY NA YES Loads “ISF Day” image preset NIGHT NA YES Lo ads “ISF Night” image preset PRESET? NA NA Returns currently-selected preset (ISF Da[...]

External Control D-73d Series Installati on/Operation Manual 107 PRE L IMINAR Y S leep Timer Command s SLEEPTMR? NA NA Returns sleep timer setting STOFF NA YES Sets the sleep timer to Off ST30MIN NA YES Sets th e sleep timer to 30 minutes ST60MIN NA YES Sets th e sleep timer to 60 minutes ST90MIN NA YES Sets th e sleep timer to 90 minutes ST2HRS NA[...]

External Control 108 D-73d Series Installation/Operation Manual PRE L IMINAR Y 6.2 Using Discrete IR Codes The DHD Controller acce pts commands in th e form of IR signals that co nform to the Phillips RC5 protocol. Ea ch DHD Controller remo te control button has an RC5 control code associated with it. You can use these codes to program a thi rd-par[...]

External Control D-73d Series Installati on/Operation Manual 109 PRE L IMINAR Y For example, here is the RC5 control code for the ON button on th e DHD Controller remote contro l unit (assuming the default add ress is used): Figure 6-1 shows the pulse train fo r this command (with the togg le bit set to zero). Figure 6-1. RC5 Me ss age Format With [...]

External Control 110 D-73d Series Installation/Operation Manual PRE L IMINAR Y IR Command List Table 6 -2 lists the RC5 control code s for the DH D Controller. ➤ Table 6-2. RC5 Control Code s for the DHD Controller Remote Control Button Name RC5 Data from Remote Control (Note) RC5 Data with Toggle Bit = 1 (Note) De s cription 16:9 0x3449 0x3C49 1[...]

External Control D-73d Series Installati on/Operation Manual 111 PRE L IMINAR Y ST60MIN 0x34 62 0x3C62 Sets the sleep timer to 60 minutes ST90MIN 0x34 63 0x3C63 Sets the sleep timer to 90 minutes ST2HRS 0x3464 0x3 C64 Sets the sleep timer to 2 hours ST4HRS 0x3465 0x3 C65 Sets the sleep timer to 4 hours UP 0x3445 0x3C45 Up-Arrow ( ) VID 1 0x344D 0x3[...]

External Control 112 D-73d Series Installation/Operation Manual PRE L IMINAR Y 6.3 Using HDMI CEC Messages The DHD Controller accept s and can respond to CEC command messag es from a disc player, satellite re ceiver or DVR/set-to p bo x via an HDMI connec tion. Using CEC, the DHD Controller can perform the following actions: • Turn itself and the[...]

External Control D-73d Series Installati on/Operation Manual 113 PRE L IMINAR Y Give Physical Address 0x83 – √ Set Stream Path 0x86 – √ Get CEC Version 0x9F – √ Abort Message 0xFF – √ User Control Pressed 0x44 – √ User Control Released 0x45 – √ Give OSD Name 0x46 – √ Menu Request 0x8D – √ Give Device Po wer Status 0x[...]

External Control 114 D-73d Series Installation/Operation Manual PRE L IMINAR Y Note s :[...]

D-73d Series Installati on/Operation Manual 115 PRE L IMINAR Y 7.1 D-73d Projector Specifications Table 7-3 lists the D-73d pr ojector specifications. 7. S pecification s Table 7-1. D-73d Projector S pecification s Projector Type: Texas Instruments Digital Ligh t Pro cessing™ (DLP) dual imaging system, SuperOnyx™ DMD™ Native Re s olution: Ful[...]

Specifications 116 D-73d Series Installation/Operation Manual PRE L IMINAR Y Light Output: 2D Content: CSMS Specifications * – Home Theater Calibration: 450 ANSI Lumens; 29 Foot-Lamberts (fL) Uncalibrated: 700 ANSI Lumens 3D Content: CSMS-3D Specifications ** – Home Theater Calibration: 311 ANSI Lumens; 20 Foot-Lamberts (fL) Uncalibrated: 483 A[...]

Specifications D-73d Series Installati on/Operation Manual 117 PRE L IMINAR Y 7.2 DHD Controller Specifications Table 7-3 lists the DHD Cont roller specifications. Table 7-2. DHD Controller S pecification s A s pect Ratio s : 4:3, Letterbox, 16:9, VirtualW ide, Cinema, Virtual Cinema, Native Video S tandard s : • HDMI and DVI with HDCP for digita[...]

Specifications 118 D-73d Series Installation/Operation Manual PRE L IMINAR Y 7.3 3Dimension Processor Specifications Table 7-3 lists the 3Dimension Processor specification s. Regulatory Appro val s : cTUVus, FCC cla ss B, CE, RoHS, China RoHS, WEEE , C-Tick, CCC, local conformances as required Limited Warranty: Two (2) years parts an d labor from t[...]

Specifications D-73d Series Installati on/Operation Manual 119 PRE L IMINAR Y 7.4 D-73d Dimensions Figure 7-1 shows the D-73d di mensions. Figure 7-1. D- 73d Dimen s ion s 21.00 533.4 20.80 528.3 4X 1.80 45.7 4X .79 MINIMUM 20.0 4.65 NOMINAL 118.1 12.42 NOMINAL 315.5 15.95 405.0 4X .31 7.9 11.00 NOMINAL 279.4 2X 17.71 449.9 1.38 35.0 7.19 182.6 16.[...]

Specifications 120 D-73d Series Installation/Operation Manual PRE L IMINAR Y 7.5 Supported Timings Table 7-4 lists the signal types supported by each input on the 3Dimen sion Processor. Table 7-4. S upported S ignal Timin g s by Input Format Re s olution Refre s h Rate (Hz) Horizontal Frequency (kHz) Pixel Frequency (MHz) S upported? ( √ = Ye s ,[...]

Specifications D-73d Series Installati on/Operation Manual 121 PRE L IMINAR Y 1280x1024 1280x1024 60.00 63.981 108.000 √√√ – – 75.00 79.976 135.000 √√√ – – 85.00 91.146 157.500 √√√ – – 1360x768 1360x768 60.00 47.712 85.500 √√√ – – 1400x1050 1400x1050 60.00 64.744 101.000 √√√ – – 60.00 65.317 121.750[...]

Specifications 122 D-73d Series Installation/Operation Manual PRE L IMINAR Y PAL-M – 59.9 4/60.00 15.734/15.750 3.580 –––– √ PAL-N – 5 0.00 15.625 3.580 –––– √ SECAM – 50.00 15.625 13.500 ––– √√ S upported 3D Mode s 1080i SBS (Side-by- Side) 1920x1080 50.00 28.125/31.250 74.250/72.000 – √ ––– 59.94 33.7[...]

Specifications D-73d Series Installati on/Operation Manual 123 PRE L IMINAR Y 1080p TAB (Top-and- Bottom) 1920x1080 23.98 26.978 74.175 – √ ––– 24.00 27.000 74.250 – √ ––– 29.97 33.716 74.175 – √ ––– 30.00 33.750 74.250 – √ ––– 50.00 56.250 148.500 – √ ––– 59.94 67.433 148.350 – √ ––– 60.0[...]

Specifications 124 D-73d Series Installation/Operation Manual PRE L IMINAR Y Note s :[...]

[...]

Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.com 020-1082-00 Rev. A May 2011[...]