Sanyo WXU700A manuel d'utilisation

Multimedia Projector MODEL PLC-WXU700A Owner ’ s Manual Network Supported □ Wireless LAN IEEE802.1 1b/g/n □ Wired LAN 100-Base-TX/10-Base-T Memory V iewer □ USB Memory Viewer * Refer to the owner ’s manuals below for details about network and memory viewer function. ■ Network Set-up and Operation ■ Memory viewer function[...]

2 Features and Design This Multimedia Projector is designed with the most advanced technology for portability , durability , and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology . ♦ Compact Design This projector is designed compact in size a[...]

3 T able of Contents T rademarks Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation. Features and Design . . . . . . . . . . . . . . . . . . .2 T able of Contents . . . . . . . . . . . . . . . . . . . . . . 3 T o t h e O w n e r .......................... 4 Safety Instruc[...]

4 T o the Owner CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE EXCEPT LAMP REPLACEMENT . REFER SERVICING T O QUALIFIED SERVICE PERSONNEL. THIS SYMBOL INDICA TES THA T DANGEROUS VOL T AGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT . THIS SYMBOL INDICA TES THA T T[...]

5 Safety Instructions All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions m[...]

6 Safety Instructions Openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. CAUTION Hot air is exhausted from the exhaust vent. When using or installing the projector , the following precautions should be taken. – Do not[...]

7 Safety Instructions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture upward, downward or backward, perpendicular to the plane of the screen as shown in the figure below . Bottom Downward (Usual) Front Downward Botto[...]

8 Compliance Federal Communications Commission Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and [...]

9 Part Names and Functions Bottom Back ⑯ ⑮ ⑭ ⑬ ⑪  ⑫ ⑰ ⑨ ⑩ ⑪ Front ⑱ ⑥ ③ ④ ⑤ ① ⑦ ⑧ ② ⑧  Kensington Security Slot This slot is for a Kensington lock used to deter theft of the projector . * Kensington is a registered trademark of ACCO Brands Corporation. ① Infrared Remote Receiver ② WIRELESS Indicator[...]

10 Part Names and Functions Rear T erminal ⑨ S-VIDEO IN Connect the S-VIDEO output signal from video equipment to this jack (p.18). ⑫ AUDIO IN Connect the audio output signal from video equipment connected to ⑨ or ⑬ to this jack. For a mono audio signal (a single audio jack), connect it to the L (MONO) jack (p.18). ⑪ COMPUTER 1 COMPONENT [...]

1 1 Part Names and Functions T op Control ⑩ LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.67, 75). ⑥ W ARNING indicator – Lights red when the projector detects an abnormal condition. – Blinks red when the internal temperature of the projector exceeds the operating range (pp.64, 75). ⑨ ON/ST AND?[...]

12 Part Names and Functions ㉘ NETWORK button Select the Network input. See the owner's manual of “Network Set-up and Operation” and owner's manual of "Memory viewer function".  Note: T o ensure safe operation, please observe the following precautions: – Do not bend, drop, or expose the remote control to moisture or he[...]

13 Part Names and Functions T o ensure safe operation, please observe the following precautions : ● Use two (2) AAA or LR03 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery . ● Avoid contact with water or liquid. ● Do not expose the remote control to moisture or heat. ● Do not d[...]

14 Part Names and Functions Spotlight Pointer Function Pointer Laser Pointer Function LASER button PRESENT A TION POINTER button This remote control emits a laser beam from the laser light window . Press the LASER button to activate the laser pointer . The signal emission indicator lights red and the red laser beam is emitted. If the LASER button i[...]

15 Part Names and Functions Adjustable Feet Projection angle can be adjusted up to 8.9 degrees with the adjustable feet. Lift the front of the projector and pull the feet lock latches on both side of the projector . Release the feet lock latches to lock the adjustable feet and rotate the adjustable feet to a proper height and tilt. Keystone distort[...]

16 Positioning the Projector For projector positioning, see the figures below . The projector should be set perpendicularly to the plane of the screen. Installation  Note: • The brightness in the room has a great influence on picture quality . It is recommended to limit ambient lighting in order to obtain the best image. • All measurements a[...]

17 Installation Installation Connecting to a Computer Cables used for connection • VGA cables (Mini D-sub 15 pin) * • USB cable • Audio cables • HDMI-DVI cable ( *One cable is supplied; other cables are not supplied with the projector .)  Note: • Input sound to the COMPUTER1 COMPONENT/COMPUTER 2 AUDIO IN terminal when using the COMPUTE[...]

18 Installation Connecting to V ideo Equipment Cables used for connection • Video and Audio cable (RCA x 3) • S-video cable • Audio cable (Cables are not supplied with the projector . ) Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables.  Note: When the AUDIO OUT is plugged-in, t[...]

19 Installation Connecting to Component V ideo Equipment  Note: • When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available. • See page 80 for ordering optional cables. Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. External Audio Equipment COMPU[...]

20 Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100-120 V or 200–240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor . T o reduce the risk of electrical shock, do not plug into any other type of power [...]

21 The preparation display will disappear after 30 seconds. (See page 58 for Lamp control status.) T urning On the Projector Connect the projector ’s AC power cord into an AC outlet. The POWER indicator lights red. Open the lens cap (see pages 9, 66). Press the ON/SY AND-BY button on the top control or on the remote control. The POWER indicator l[...]

22 What is PIN code? PIN (Personal Identification Number) code is a security code that allows the person who knows it to operate the projector . Setting a PIN code prevents unauthorized use of the projector . A PIN code consists of a four-digit number . Refer to the PIN code lock function in the Setting Menu on pages 59-60 for locking operation of [...]

23 TO MAINT AIN THE LIFE OF THE LAMP , ONCE YOU TURN THE PROJECT OR ON, W AIT A T LEAST FIVE MINUTES BEFORE TURNING IT OFF . Power off? disappears after 4 seconds. T urning Off the Projector Press the ON/ST AND-BY button on the top control or on the remote control, and Power off? appears on the screen. Press the ON/ST AND-BY button again to turn of[...]

24 Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. The menus have a hierarchical structure, with a main menu that is divided into submenus, which are further divided into other submenus. For each adjustment and setting procedure, refer to respective sections in this manual. Use the Poin[...]

25 Menu Bar For detailed functions of each menu, see “Menu T ree” on pages 73-74. Basic Operation         Main Menu Sub-Menu    Image select For computer source, used to select an image mode among Dynamic , Standard , Real , Blackboard(Green) , Colorboard and image 1 - 4 (p.36). For HDMI or Video source, used to[...]

26 Basic Operation Rotate the Zoom Lever to zoom in and out. Rotate the Focus Ring to adjust the focus of the image. Zoom and Focus Adjustment If a projected picture still has keystone distortion after pressing the AUTO SETUP/CANCEL button on the top control or the AUTO SET/CANCEL button on the remote control, correct the image manually as follows:[...]

27 Sound Adjustment 1 2 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Sound . Press the Point ► or the SELECT button to access the submenu items. Press the VOLUME+/– buttons on the top control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few second[...]

28 Basic Operation Remote Control Operation Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons enables you to make the desired operation quickly without calling up the On-Screen Menu. Press the HDMI, COMPUTER, VIDEO or NETWORK button on the remote control to select the input source. See pages[...]

29 Basic Operation black out → the captured image → normal → • • • • • Press the NO SHOW button on the remote control to black out the image. T o restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as User in the Logo selection (see page 50), the screen changes each[...]

30 Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below . 1 Input Menu 2 3 Input Source Selection (Computer 1: RGB / Component / RGB(Scart) ) Computer Input  Note: When the[...]

31 Computer Input Choose Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below . Input Source Selection (Computer 2: RGB) Direct Operation Menu Operation  Note: When the Input Sear[...]

32 Computer Input PC System Menu PC System Menu Computer System Selection This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC adjustment. If a computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional [...]

33 Computer Input Auto PC adjustment function is provided to automatically adjust Fine sync , T otal dots , Horizontal , V ertical , Clamp , Display area H and Display area V positions to conform to your computer . PC adjust Menu Auto PC adjustment T o store adjustment parameters The adjusted parameters from the Auto PC adjustment can be stored in [...]

34 Computer Input PC adjust Menu Manual PC adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector . Manual PC adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually a[...]

35 Store T o store the adjusted data, select Store and then press the Point ► or the SELECT button. Move the highlight to one of the Modes 1 to 5 in which you want to store, and then press the SELECT button. Mode free T o clear the stored data, select Mode free and then press the Point ► or the SELECT button. Move the highlight to the mode that[...]

36 Computer Input Image Select Menu IMAGE button Dynamic Real Image 1 Image 2 Image 3 Image Mode Selection Image 4 Blackboard (Green) Standard Remote Control IMAGE button Select the desired image mode among Dynamic , Standard , Real , Blackboard (Green) , Colorboard , Image 1 , Image 2 , Image 3 and Image 4 by pressing the IMAGE button on the remot[...]

37 Computer Input Image Adjust Menu Image Adjustment Reset Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button. 1 2 Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box. Use the[...]

38 Computer Input Store This projector has the picture screen resize function, which enables you to customize the image size. Screen Menu Screen Size Adjustment Provide the image to fit the screen size. Normal T rue Provide the image in its original size. When the original image size is larger than the screen size (1280 x 800), the projector enters[...]

39 Computer Input Select Digital zoom + . The On-Screen Menu disappears and D. zoom + appears. Press the SELECT button to expand the image size. Use the Point ▲▼◄► buttons to pan the image. The Panning function can work only when the image is larger than the screen size. A projected image can be also expanded by pressing the D.ZOOM + button[...]

40 Choose Video or S-video by pressing the INPUT button on the top control or the VIDEO button on the remote control. 1 2 Video Input Menu Input Source Selection (V ideo, S-video) V ideo Input Direct Operation Menu Operation When video input signal is connected to the VIDEO jack, select Video . Video When video input signal is connected to the S- V[...]

41 V ideo Input Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control; choose HDMI by pressing the INPUT button on the top control or press the HDMI button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described belo[...]

42 V ideo Input V ideo System Selection 1 A V System Menu (Video or S-video) A V System Menu (Component) 2 If the projector cannot reproduce proper video image, select a specific broadcast signal format from among P AL , SECAM, NTSC , NTSC 4.43 , P AL-M and P AL-N . P AL/SECAM/NTSC/NTSC4.43/P AL-M/P AL-N The projector automatically detects an incom[...]

43 Image Select Menu Select the desired image mode among Dynamic , Standard , Cinema , Blackboard (Green) , Colorboard , Image 1 , Image 2 , Image 3 and Image 4 by pressing the IMAGE button on the remote control. Standard Picture mode adjusted with fine tone. Cinema Blackboard (Green) Image 1–4 IMAGE button Dynamic Cinema Image Mode Selection Bla[...]

44 V ideo Input Image Adjustment 1 2 Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63). Press the Point ◄ button to decrease the brightness; press the Point ► button to increase the brightness (from 0 to 63). Contrast Brightness Press the Point ◄ button to lighten red tone;[...]

45 V ideo Input Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15). Gamma Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 15). Sharpness An interlaced video signal can be displayed in progressive [...]

46 V ideo Input This projector has the picture screen resize function, which enables you to customize the image size. Normal Screen Size Adjustment Screen Menu 1 2 Provide the image to fit the screen size while maintaining the aspect ratio of input signal. Custom Adjust the screen scale and position manually with this function. Press the Point ► [...]

47 HDMI setup T erminal Computer 2 Pointer Dot Standby mode Eco Language The language used in the On-Screen Menu is available in English , German , French , Italian , Spanish , Portuguese , Dutch , Swedish , Finnish , Polish , Hungarian , Romanian , Russian , Chinese , Korean , Japanese and Thai . Setting Menu Setting Setting HDMI setup T erminal C[...]

48 Setting  Note: • Auto Keystone corrects vertical distortion only , not correct horizontal distortion. • The Auto Keystone function cannot work when the Ceiling feature is set On in the Setting menu (p.53). • Perfect correction of the image distortion cannot be ensured with the Auto setup function. If the distortion is not corrected prop[...]

49 Keystone This function is used to store or reset the keystone correction when the AC power cord is unplugged. Store ....... Keep the keystone correction even when the AC power cord is unplugged. Reset ....... Release the keystone correction when the AC power cord is unplugged. T o correct keystone distortion, press the SELECT button. Keystone ap[...]

50 Setting Logo (Logo and Logo PIN code lock settings) HDMI setup T erminal Computer 2 Pointer Dot Standby mode Eco Logo select This function allows you to customize the screen logo with Logo select , capture , Logo PIN code lock and Logo PIN code change functions.  Note: When On is selected in the Logo PIN code lock function, Logo select , capt[...]

51 Off Capture Capture This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Select Capture and press the SELECT button. A confirmation box appears and select Y es to capture the projected image. After capturing the projected image, go to the Logo select function and set it t[...]

52 Setting Enter a Logo PIN code Use the Point ▲▼ buttons to enter a number . Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to  . If you fixed an incorrect number , use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct numbe[...]

53 Setting Ceiling Rear Ceiling When this function is set to O n , the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector . Rear When this function is set to On , the picture will be left/right reversed. This function is used to project the image from rear of the screen. [...]

54 Setting Arrow Pointer Pointer Y ou can emphasize a part of the projected image with this function. Use the Point ▲▼ buttons to choose Spotlight ( Large , Middle or Small ) , Arrow , Finger or Dot and press the SELECT button. See "Pointer Function" on page 14. Standby mode This function is available when operating the projector via [...]

55 Setting Picture in Picture This function is used to project two videos simultaneously by placing a separate small sub screen within the main screen. (Picture in Picture combinations provided in this projector are shown on pages 78.) Only the sound on the main picture is heard, the sound on the sub picture cannot be heard.( In P in P , the big pi[...]

56 Power management T imer left before Lamp is off . Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period. Select one of the following options: Ready .................. When the lamp has been fully coo[...]

57 Setting On start When this function is set to On , the projector will be automatically turned on just by connecting the AC power cord to a wall outlet.  Note: Be sure to turn off the projector properly (see "T urning Off the Projector" on page 23). If the projector is turned off in the incorrect sequence, the On start function does [...]

58 Remote control Lamp control Remote control The eight different remote control codes ( Code 1 - Code 8 ) are assigned to the projector; the factory-set, initial code ( Code 1 ) and the other seven codes ( Code 2 to Code 8 ). The same code should set on both the projector and the remote control. For example, operating the projector in Code 7 , the[...]

59 Setting Key lock Key lock Security (Key lock and PIN code lock) PIN code lock This function locks the top control and remote control buttons to prevent operation by unauthorized persons. ..... Unlocked. ..... Lock the operation of the top control. T o unlock, use the remote control. ..... Lock the operation of the remote control. T o unlock, use[...]

60 Setting Use the Point ▲▼ buttons to select Off , On1 or On2 . Press the SELECT button to close the dialog box. Change the PIN code lock setting Enter a PIN code Use the Point ▲▼ buttons to enter a number . Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to  . If you fixed[...]

61 This function provides the following options in the cooling fans’ operation when the projector is turned of f (p.23). L1 ...... Normal operation L2 ...... Slower and lower-sound than the normal operation ( L1 ), but it takes more time to cool the projector down. Fan Setting Fan control 0º 90 º 180 º 40 º 50 º 14 0 º 50 º 40 º Fan Contr[...]

62 Setting Factory default This function returns all setting values except for the User logo , PIN code lock , Logo PIN code lock and Filter counter to the factory default settings. Factory default W arning log This function records anomalous operations while the projector is in operation and use it when diagnosing faults. Up to 10 warning logs are[...]

63 Input Source Information Display The Information Menu is used for checking the status of the image signal being projected and the operation of the projector . H-sync freq. V -sync freq. Lamp counter Information Menu The horizontal frequency of the input signal is displayed in KHz or - - - - - when no signal. The vertical frequency of the input s[...]

64 The W ARNING indicator shows the state of the function which protects the projector . Check the state of the W ARNING indicator and the POWER indicator to take proper maintenance. W ARNING indicator The projector is shut down and the W ARNING indicator is blinking red. When the temperature inside the projector reaches a certain level, the projec[...]

65 Maintenance and Cleaning Filter prevents dust from accumulating on the optical elements inside the projector . Should the filters become clogged with dust particles, it will reduce cooling fans’ ef fectiveness and may result in internal heat buildup and adversely affect the life of the projector . If a Filter warning icon appears on the screen[...]

66 Maintenance and Cleaning Cleaning the Projector Cabinet Cleaning the Projection Lens Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner or use a lens cleaning paper or commercially available air blower to clean the lens. Avoid using an e[...]

67 Maintenance and Cleaning When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow . Replace the lamp with a new one promptly . The timing when the LAMP REPLACE indicator should light is depending on the lamp mode. For continued safety , replace wit[...]

68 Maintenance and Cleaning This projector uses a high-pressure lamp which must be handled carefully and properly . Improper handling may result in accidents, injury , or create a fire hazard. ● Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same life for each lamp. Some lamps may fail[...]

69 Lamp counter Reset? appears. Select Y es , then another confirmation box appears. Problem: – Solutions – Plug the power cord of the projector into the AC outlet. – See if the POWER indicator lights red. – W ait until the POWER indicator stops blinking to turn on the projector again. The projector can be turned on after the POWER indicato[...]

70 Appendix – Check the connection between your computer or video equipment and the projector . See pages 17-19. – See if the input signal is correctly output from your computer . Some laptop computers may need to change the setting for monitor output when connecting to a projector . See your computer ’s instruction manual for the setting. ?[...]

71 Appendix – Check PC adjustment or Screen and adjust them. See pages 34-35, 38-39 . – PIN code lock is being set. Enter a PIN code (" 1234" or numbers you have set). See pages 22, 59-60. – Make sure your computer is connected to the projector with USB cable. See page 17. – Check cable connection between the projector and your co[...]

72 W ARNING : High voltages are used to operate this projector . Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center . Specify the model number and explain about the problem. We will advise you how to obtain service. This[...]

73 Appendix Menu T ree SVGA 1 Mode 1 Mode 2 - - - - T otal dots Horizontal V ertical Display area H Display area V Reset Dynamic Real Blackboard (Green) Image 1 Image 2 Image 3 Image Adjust Contrast Brightness Color temp. Red Gamma Store Normal T rue Digital zoom – Full 0–63 0–63 Computer Input PC adjust Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Ima[...]

74 Appendix Auto P AL SECAM NTSC NTSC 4.43 P AL-M P AL-N HDMI Input / Video Input Auto 1080i 1035i 720p 575p 480p 575i 480i Dynamic Cinema Blackboard (Green) Image 1 Image 2 Image 3 Normal 0–63 0–63 Off Setting Image Select System (2) System (3) Image Adjust Contrast Brightness Color T int Red Green Blue Sharpness Reset Store Gamma Progressive [...]

75 Check the indicators for projector condition. • • • green • • • red • • • of f • • • blinks green When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow . When this indicator lights yellow , replace the projection lamp with a new one promptly . The projector is off. (The AC power cord i[...]

76 Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V -, H-Frequency mentioned below and less than 140 MHz of Dot Clock for analog signal and 1 10 MHz of Dot Clock for digital signal. When selecting these modes, PC adjustment can be limited. ON-SCREEN DISPLA Y RESOLUTION H-Freq. [...]

77 Appendix ON-SCREEN DISPLA Y RESOLUTION H-Freq. (KHz) V -Freq. (Hz) D-VGA 640 x 480 31.47 59.94 D-480p 720 x 480 ---- 59.94 D-575p 720 x 575 ---- 50.00 D-SVGA 800 x 600 37.879 60.32 D-WXGA 1 1366 x 768 48.36 60.00 ON-SCREEN DISPLA Y RESOLUTION H-Freq. (KHz) V -Freq. (Hz) D-1035i 1920 x 1035 D-1080i 1920 x 1080 D-1080i 1920 x 1080 33.75 60.00 (Int[...]

78 List of Picture in Picture o : Picture in Picture combinations are enabled - : Picture in Picture combinations are disabled  Note: • When the input signal(s) is/are incompatible, X mark will be displayed on the Main/Sub picture. • Depending on the frequency or signal type of PC/A V input, the display resolution may be lowered or images ma[...]

79 Appendix T echnical Specifications Mechanical Information Projector T ype Multi-media Projector Dimensions (W x H x D) 13.16" x 3.09" x 10.14" (334.2 x 78.4 x 257.5mm) (Not including protrusions) Net Weight 7.94 lbs (3.6 kg) Feet Adjustment 0˚ to 8.9˚ Panel Resolution LCD Panel System 0.74" TFT Active Matrix type, 3 panels [...]

80 Appendix Model No. COMPONENT~VGA Cable : POA-CA-COMPVGA SCART~VGA Cable : POA-CA-SCART VGA-Cable (10 m) : KA-MC-DB10 The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. to the sales dealer . Optional Parts Accessories Owner ’s Manual (CD-ROM) Quick Reference Guide Safety Manual AC Pow[...]

81 This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see page 51 on the owner ’s manual of “Network Set-up and Oper[...]

82 Vcc - Data + Data Ground 1 2 3 4 2 3 4 1  COMPUTER IN 1 /COMPONENT IN /MONITOR OUT (ANALOG) T erminal: Analog RGB (Mini D-sub 15 pin) 5 1 2 3 4 10 9 6 7 8 15 14 13 11 12 Configurations of T erminals Red (R/Cr) Input/Output Ground (Horiz.sync.) Green (G/Y) Input/Output ----- Blue (B/Cb) Input/Output Ground (Red) Ground (Green) Ground (Blue) 1 [...]

83 Appendix Write down the PIN code number in the column below and keep it with this manual securely . If you forgot or lost the number and unable to operate the projector , contact the service station. PIN Code Number Memo Factory default set No: 1 2 3 4* Factory default set No: 4 3 2 1* Put the label below (supplied) on in a prominent place of th[...]

84 Appendix Dimensions Unit: inch (mm) Screw Holes for Ceiling Mount Screw: M4 Depth: 12.0(0.472) 10.14 (257.5) 13.16(334.2) 2.14(53.8) 3.17(80.5) 3.09(78.4) 5.08(129.0) 5.20(132.0) 2.78(70.5) 5.08(129.0) 4.43(1 12.5) 5.51(140.0) 3.66(93.0)[...]

KY7AE[...]