Français dropdown-ico

Sears 153.326462 40 GAL. manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Sears 153.326462 40 GAL.. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Sears 153.326462 40 GAL. ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Sears 153.326462 40 GAL. décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Sears 153.326462 40 GAL. devrait contenir:
- informations sur les caractéristiques techniques du dispositif Sears 153.326462 40 GAL.
- nom du fabricant et année de fabrication Sears 153.326462 40 GAL.
- instructions d'utilisation, de réglage et d’entretien de l'équipement Sears 153.326462 40 GAL.
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Sears 153.326462 40 GAL. ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Sears 153.326462 40 GAL. et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Sears en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Sears 153.326462 40 GAL., comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Sears 153.326462 40 GAL., l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Sears 153.326462 40 GAL.. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    1 SA VE THIS MANUAL FOR FUTURE REFERENCE. Owner ’ s Manual FOR POT ABLE W A TER HEA TING ONL Y . NOT SUIT ABLE FOR SP ACE HEA TING . POWER MISER™ 6 ELECTRIC W A TER HEA TER Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A www.sears.com PRINTED 0707 185796-000 GAMA certification applies to all residential electric water heaters with capac[...]

  • Page 2

    2 SAFE INST ALLA TION, USE AND SER VICE Y our safety and the safety of others is extremely important in the installation, use and servicing of this water heater . Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and others of a potential injury hazard. Read and obey all safety [...]

  • Page 3

    3 GENERAL SAFETY[...]

  • Page 4

    4 SAFE INST ALLA TION, USE AND SER VICE ............................................................................................. ........................................... 2 GENERAL SAFETY ...........................................................................................................................................................[...]

  • Page 5

    5 Thank Y ou for purchasing a Sears water heater . Properly installed and maintained, it should give you years of trouble free service. It is strongly suggested that this new water heater be professionally installed, contact the local Sears Service Center or any Sears store. They will arrange for prompt, quality installation by Sears authorized con[...]

  • Page 6

    6 MA TERIALS AND BASIC T OOLS NEEDED Basic T ools Y ou may or may not need all of these tools, depending on your type of installation. These tools can be purchased at your local Sears store. Pipe Wrench (2) Screwdriver 6 Foot T ape or Folding Rule Garden Hose Drill Pipe Dope or T eflon T ape Additional T ools Needed When Sweat Soldering T ubing Cut[...]

  • Page 7

    7 Removing the Old W ater Heater 1. T urn “OFF” electrical supply to the water heater . FIGURE 1. 2. Turn “OFF” the water supply to the water heater at the water shut-off valve or water meter . FIGURE 2. 3. Attach a hose to the water heater drain valve and put the other end in a floor drain or outdoors. Open the water drain valve. Open a ne[...]

  • Page 8

    8 Mineral buildup or sediment may have accumulated in the old water heater . This causes the water heater to be much heavier than normal and this residue, if spilled out, could cause staining. Fact s to Consider About the Location Y ou should carefully choose an indoor location for the new water heater , because the placement is a very important co[...]

  • Page 9

    9 Before making the conversion to 5500 watts, check the (1) power supply . . . must be 240 volts, (2) wiring . . . 10 gauge AWG @ T ype T W, 60°C or equivalent, and (3) Circuit breakers or fusing . . .capable of 30 amp loading. Also, the installation must conform with this manual, local codes and electric utility rules. Failure to comply can resul[...]

  • Page 10

    10 NOTE: T o protect against untimely corrosion of hot and cold water fittings, it is strongly recommended that di-electric unions or couplings be installed on this water heater when connected to copper pipe. 1. Look at the top cover of the water heater . The hot water outlet is marked hot. Put two or three turns of teflon tape around the threaded [...]

  • Page 11

    11 Position the valve downward and provide tubing so that any discharge will exit only within 6 inches (153 mm) above, or at any distance below the structural floor . Be certain that no contact is made with any live electrical part. The discharge opening must not be blocked or reduced in size under any circumstances. Excessive length, over 30 feet [...]

  • Page 12

    12 Converting the Lower Element These instructions only cover the conversion of the convertible element, read this entire manual before attempting to install or operate the water heater . The water heater is factory set to operate at 3800 watts. The lower element can be converted to operate at 5500 watts. Refer to “Facts to Consider About the Con[...]

  • Page 13

    13 FIGURE 16. 5. Remove the screws from terminal 2 of the element, and move the looped end of the wire aside. FIGURE 17. 6. The buss bar is labeled 5500 W . Place the buss bar over terminals 2 and 3 with the 5500 W visible. Install the extra screw provided into terminal 3. FIGURE 18. 7. The wire removed from terminal 2 has a looped end. It must rem[...]

  • Page 14

    14 1 1. Replace the access panel. FIGURE 21. 12. Complete wiring to the water heater , or if completed, turn “ON” electric power to the water heater after filling the tank with water . FIGURE 22. Never use this water heater unless it is completely full of water . T o prevent damage to the tank and heating element, the t ank must be filled with [...]

  • Page 15

    15 5. Wiring Diagrams (see “Wiring Diagrams” section) have been supplied showing the two most common types of connections between the water heater and the power supply . Y ou can easily see which type connection you have by removing the junction box cover on top of the water heater . • T wo Wire Connection Diagrams: is the most common requiri[...]

  • Page 16

    16 Wiring Diagrams FIGURE 25. ST ANDARD WIRING FOR 2 WIRE LEAD W A TER HEA TERS NON-SIMUL T ANEOUS OPERA TION 240 VOL T DOUBLE ELEMENT WIRING FOR 3 WIRE LEAD W A TER HEA TERS NON-SIMUL T ANEOUS OPERA TION 240 VOL T DOUBLE ELEMENT *NOTE: Some lower Hi-T emp Limit Switches may have 4 terminals. Use only the 2 terminals on left. FIGURE 24. A6 A9[...]

  • Page 17

    17 T emperature Regulation HOTTER WA TER CAN SCALD: Water heaters are intended to produce hot water . Water heated to a temperature which will satisfy clothes washing, dish washing, and other sanitizing needs can scald and permanently injure you upon contact. Some people are more likely to be permanently injured by hot water than others. These incl[...]

  • Page 18

    18 The upper and lower thermostats are adjustable if a different water temperature is desired. Read all warnings in the “T emperature-Regulation” section before proceeding. 1. Turn “OFF” the electric power to the water heater at the junction box. 2. T ake off the upper and/or lower access panel, insulation cap with handle. 3. The slotted ad[...]

  • Page 19

    19 The water heater should be drained if being shut down during freezing temperatures. Also, periodic draining and cleaning of sediment from the tank may be necessary . 1. Before beginning turn “OFF” the electric power supply to the water heater . 2. CLOSE the cold water inlet valve to the water heater . 3. OPEN a nearby hot water faucet and le[...]

  • Page 20

    20 1. Before beginning turn “OFF” the electric power supply to the water heater . FIGURE 30. 2. Turn off the water supply to the water heater at the water Shut-off valve or water meter . FIGURE 31. 3. Attach a hose to the water heater drain valve and put the other end in a floor drain or outdoors. Open the water heater drain valve. Open a nearb[...]

  • Page 21

    21 8. Clean the area around the element opening. Remove any sediment from or around the element opening, inside the tank. 9. If you are cleaning the element you have removed, do so by scraping or soaking in vinegar or a de-liming solution. Replacement elements must (1) be the same voltage and (2) no greater wattage than listed on the model rating p[...]

  • Page 22

    22 18. Replace access panel. 19. T urn “ON” electric power to water heater . FIGURE 41. Drain V alve W asher Replacement . NOTE: For replacement, use a 17/32" x 13/64" x 1/8" thick washer available at your nearest hardware store. For ordering a replacement washer , refer to the “Repair Part s List” section. • Before beginni[...]

  • Page 23

    23 Start Up Conditions THERMAL EXP ANSION W ater supply systems may , because of such events as high line pressure, frequent cut-offs, the effects of water hammer among others, have installed devices such as pressure reducing valves, check valves, back flow preventers, etc...to control these types of problems. When these devices are not equipped wi[...]

  • Page 24

    24 D. An excess of active hydrogen in the tank. This is caused by corrosion protective action of the anode. Smelly water may be eliminated or reduced in some water heater models by replacing the anode rod (s) with one of less active material, and then chlorinating the water heater tank and all hot water lines. Contact the local Sears Service Center[...]

  • Page 25

    25 2. Make sure the electrical supply to your water heater is “ON”. 3. Check for loose or blown fuses in your water heater circuit. Circuit breakers weaken with age and may not handle their rated load and should be replaced. 4. Make certain the disconnect switch, if used, is in the “ON” position. 5. Check to see the electric service to your[...]

  • Page 26

    26 LEAKAGE CHECKPOINTS Read this manual first. Then before checking the water heater make sure the electric supply has been turned “OFF”, and never turn the electric supply “on” before the tank is completely full of water . Use this guide to check a “Leaking” water heater . Many suspected “Leakers” are not leaking tanks. Often the s[...]

  • Page 27

    27 KENMORE POWER MISER TM 6 ELECTRIC W A TER HEA TERS NOTE:A UPPER ELEMENT : These water heaters are equipped with 3800 watt elements. LOWER ELEMENT : These water heaters are equipped with factory installed convertible elements, which can be operated at 3800 watts or 5500 watts. Convertible elements are not offered as replacement parts. ELEMENT ORD[...]

  • Page 28

    28 Now that you have purchased this water heater , should a need ever exist for repair parts or service, simply contact any Sears Service Center or call 1-800-4-MY -HOME ® (1-800-469-4663). Be sure to provide all pertinent facts when you call or visit. All Parts listed may be ordered from any Sears Service Center and by calling 1-800-366-P ART (1-[...]

  • Page 29

    29 Now that you have purchased this water heater , should a need ever exist for repair parts or service, simply contact any Sears Service Center or call 1-800-4-MY -HOME ® (1-800-469-4663). Be sure to provide all pertinent facts when you call or visit. All Parts listed may be ordered from any Sears Service Center and by calling 1-800-366-P ART (1-[...]

  • Page 30

    30 NOTES[...]

  • Page 31

    31 NOTES[...]

  • Page 32

    32 6 - YEAR LIMITED W ARRANTY ON WA TER HEA TER For six years from the date of purchase, if this water heater is installed and operated in a single-family home in accordance with the owner’s manual instructions and all local applicable plumbing codes, Sears will: 1. Supply free water heater parts for those that are defective in material or workma[...]