Français dropdown-ico

Shindaiwa X7502831200 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Shindaiwa X7502831200. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Shindaiwa X7502831200 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Shindaiwa X7502831200 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Shindaiwa X7502831200 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Shindaiwa X7502831200
- nom du fabricant et année de fabrication Shindaiwa X7502831200
- instructions d'utilisation, de réglage et d’entretien de l'équipement Shindaiwa X7502831200
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Shindaiwa X7502831200 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Shindaiwa X7502831200 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Shindaiwa en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Shindaiwa X7502831200, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Shindaiwa X7502831200, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Shindaiwa X7502831200. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    T344 TRIMMER SHIND AIWA OWNER’S/OPERA T OR’S MANU AL WARNING! Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing pro- tection when operating this unit. X7502831200 05/10[...]

  • Page 2

    2 The Shindaiwa H4 series of hand-held power equipment is designed and built to deliver superior performance and reliability without compromise to quality , comfort, safety or durability . Shindaiwa engines represent the leading edge of high-perfor- mance engine technology , delivering exceptionally high power with remarkably low displacement and w[...]

  • Page 3

    3 W ARNING! Engine exhaust IS HOT , and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause uncon- sciousness, serious injury , or death. Exhaust can cause serious burns. AL WA YS position unit so that exhaust is directed away from your face and body . War ning and Operational Labels Read and fol low t his oper ator' s manu al.[...]

  • Page 4

    4 T he Proper ly Equipped Oper a tor Always wear a harness when operating the unit . It adds comfort and helps ensure safety by limiting movement fore and aft. When the harness is adjusted properly , the unit should balance with the cutting attachment parallel to the ground. Always operate with both hands rmly gripping the unit. Wear close-tt[...]

  • Page 5

    5 Be Aware of the Wor king En vir onment Avoid long-term operation in very hot or very cold weather . Make sure bystanders or observers outside the 15 meter (50 feet) “danger zone” wear eye protection. Be extremely careful of slippery terrain, especially during rainy weather . If contact is made with a hard object, stop the engine and inspect t[...]

  • Page 6

    6 Specications Engine Name T344 Engine T ype 4-cycle, vertical cylinder , air cooled Dry Weight (Without guard and strap) 5.9 kg/13.0 lb. Bore x Stroke 38 x 30 mm (1.5 x 1.2 in.) Displacement 34 cc (2.1 cu. in.) Fuel/Oil Ratio 50:1 with *ISO-L-EGD or JASO FD class engine oil Fuel T ank Capacity 700 ml (23.7 oz.) Carburetor T ype Diaphragm-type c[...]

  • Page 7

    7 NOTE The plastic shield is for use with the Nylon Line Head only . Install Metal Shield when using plastic or metal blades. Remove plastic threaded shaft sleeve and adapter plate (C) from PTO 1. shaft (A). Place the shield on the bottom of the bearing housing ange. 2. Place shield plate (B) on shield, align holes. Install three (3) screws from[...]

  • Page 8

    8 Throttle lever free play 4-6 mm (3/16”-1/4”) Throttle Free Play Adjust throttle lev er fr ee play The throttle lever free play should be approximately 4 - 6 mm (3/16” - 1/4”). Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever free play , follow the procedures and illustrations[...]

  • Page 9

    9 Handling Fuel DANGER Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container . • DO NOT smoke near fuel. • DO NOT allow ames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equaliz[...]

  • Page 10

    10 Filling the fuel tank WARNING! Minimize the Risk of Fire Place the unit on a at, level surface. 1. Clear any dirt or other debris from around the fuel ller cap. 2. Remove the fuel cap, and ll the tank with clean, fresh fuel. 3. Reinstall the fuel ller cap and tighten rmly . 4. Wipe away any spilled fuel before starting engine. 5. [...]

  • Page 11

    11 Slide the ignition switch to the “ON” position. 1. Set the throttle trigger to the “fast idle”: 2. Slide ignition to ON ON Throttle T rigger Make sure the attachment is clear of obstructions! ...and pull recoil starter handle upward Hold the unit rmly ... Close choke Set the choke lever to the CLOSED position Star ting the Engine IMPO[...]

  • Page 12

    12 Slide ignition to OFF OFF NEVER operate the unit with the cutting attachment shield or other protec - tive devices removed! Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer . Do not make modications to this unit without written approval from Shindaiwa, Inc. AL W A YS make sure the cutting attachment is properly [...]

  • Page 13

    13 Operation W ARNING Engine exhaust IS HOT , and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause uncon- sciousness, serious injury , or death. Exhaust can cause serious burns. AL WA YS position unit so that exhaust is directed away from your face and body . CA UTION! Do not push the rotating line into trees, ■ wire fences or [...]

  • Page 14

    14 Maintenance WARNING! Before performing any main- tenance, repair , or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance. WARNING! Non-standard accessories, cut - ting attachment, or replacement parts may not operate properly with [...]

  • Page 15

    15 spark plug gap--all models Components of air lter Filter element Prelter Loosen fasteners Remove the cover of the air lter Maintenance (continued) 10-Hour maintenance (more fr equently in dusty conditions) Remove the air lter cover by loos - 1. ening the cover screw(s) and lifting. Remove and inspect the pre-lter . 2. If the pre-?[...]

  • Page 16

    16 Maintenance (continued) Remove and replace the fuel lter element. Use a hooked wire to extract the ■ fuel lter from inside the fuel tank. Inspect the fuel lter element. If it shows signs of contamination, replace with a genuine Shindaiwa replacement fuel lter element. Before reinstalling the new lter ele - ■ ment, inspect the [...]

  • Page 17

    17 135-Hour Maintenance IMPORT ANT! If a new gasket is not available and/ or the old gasket is not damaged, the old gasket may be reused. Never use cracked or damaged gaskets! T urn engine over several times, and 6. returnthe to TDC-compression. Recheck with proper feeler gauge to make sure clearance adjust- ment did not change as a result of tight[...]

  • Page 18

    18 Engine Cover Screws Engine Cover Mufer Mufer Gasket Mufer Bolts Spark Arrester Screen Spark Arrester Cover Cover Screws With a 3 mm hex wrench remove the 1. engine cover screws and the engine cover . If the engine becomes sluggish and low on power , check and clean the spark arrester screen. IMPORT ANT! If you note excessive carbon buil[...]

  • Page 19

    19 Adjusting Engine Idle The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment. WARNING! The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described[...]

  • Page 20

    20 T r oubleshooting Guide V aporlock. V alve adjustment. Engine hot/heat soaked. Low fuel quality . V alve clearance too tight. V alve clearance too loose. Let cool completely and restar t. Refill with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO [...]

  • Page 21

    21 Is the engine overheating? Engine is rough at all speeds. May also have black smoke and/or unbur ned fuel at the exhaust. Operator is over working the unit. Carburetor mixture is too lean. Improper fuel ratio. Fan, fan cover , cylinder fins dir ty or damaged. Carbon deposits on the piston or in the muf fler . Clogged air cleaner element. Loose[...]

  • Page 22

    22 ADDITIONAL PROBLEMS Poor acceleration. Clogged air filter . Clogged fuel filter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel filter . Shor ted spark plug or loose ter minal. Ignition failure. Piston seizure. Ground (stop) wire is disconnected, or switch is d[...]

  • Page 23

    23 SHINDAIW A LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO, INC'S RESPONSIBILITY ECHO Incorporated’s (ECHO, INC.) Limited W arranty , provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship. Under normal use and maintenance from date of purc[...]

  • Page 24

    24 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. T o help ensure the performance of the unit, it is required to use engine oil which meets[...]

  • Page 25

    25 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small of f-road engine (SORE). New equ[...]

  • Page 26

    26 NO TES[...]

  • Page 27

    27 NO TES[...]

  • Page 28

    ECHO Incorporated. 400 Oakwood Road Lake Zurich, IL 60047-1564 U.S.A. T elephone: 1-877-986-7783 Fax: 1-847-540-8416 www .shindaiwa.com Y amabiko Corporation 7-2 Suehirocho 1-Chome, Ohme, T okyo, 198-8760, Japan Phone: 81-428-32-61 18 Fax: 81-428-32-6145 Copyright© 2010 By Echo, Incorporated All Rights Reserved. T1481 1001001/T1481 1999999 T147120[...]