Français dropdown-ico

Singer 14T957DC manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Singer 14T957DC. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Singer 14T957DC ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Singer 14T957DC décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Singer 14T957DC devrait contenir:
- informations sur les caractéristiques techniques du dispositif Singer 14T957DC
- nom du fabricant et année de fabrication Singer 14T957DC
- instructions d'utilisation, de réglage et d’entretien de l'équipement Singer 14T957DC
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Singer 14T957DC ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Singer 14T957DC et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Singer en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Singer 14T957DC, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Singer 14T957DC, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Singer 14T957DC. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    DETAILED THREADING GUIDE - Quantumlock® 14T967DC & 14T957DC 2 / 3 / 4 / 5 – THREAD SERGERS TABLE OF CONTENTS THREADING INFORMATION FOR A 4-THREAD UL TRA STRETCH MOCK S AFETY STITCH ........... 2 THREADIING INFORMATION FOR A NARR OW 5-THREAD SAF ETY STITCH .................................... 11 THREADING INFORMATION FOR A TRIPLE COVE R STITC[...]

  • Page 2

    THREADING INFORMATION FOR A 4-THRE AD ULTRA STRETCH MOCK SAFETY STITCH Threading the Green Upper Looper: Top Cover Thread Guide. Thread the top cover thread guide by slipping t he thread under the guide from right to left, and then pull t he thread under the small r ound disk from the right side. Lay thread through Green te nsion disk, while holdin[...]

  • Page 3

    Using tweezers slip the thread into the next three guides marked with small green dots. Thread the g uide that looks l ike a little pigt ail and then thread th rough the eye of the looper as shown. Pull th e thread tail to the back of the serger approximately 4 to 6 inches.[...]

  • Page 4

    Thread Red Lower Looper: Top Cover Thread Guide Thread the top cover thread guide by slipping t he thread under the guide from right to left, and then pull t he thread under the small r ound disk from the right side. Lay thread through Red tensio n disk while holdin g the thread securely with both hands. Next slip into guide directly below the te n[...]

  • Page 5

    Tugging slight ly on the thre ad tail at the back of th e serger, push the threader lever all the way up to hook thread in to the eye at the ba ck of the looper. Threading Blue Overedge Stitch Needle: Top Cover Thread Guide Thread the top cover thread guide by slipping t he thread under the guide from right to left, and then pull t he thread under [...]

  • Page 6

    Using tweezers slip the thread into the slot at the back of the thread guide, a nd then into th e next th ree guides marked with the small red dots. Thread the eye of the looper as shown, maki ng sure that the thread is positioned in the “V” cutout in front of the looper. Pull the thre ad tail to the back of th e serger approximately 4 to 6 inc[...]

  • Page 7

    Lay thread through Blue tension disk while holding the thread securely with both hands. Next slip into guide directly below the te nsion from right to left. Slip the thread into the third slot clos est to the back and then up and over the take up lever slot.[...]

  • Page 8

    Slip the thread into the thir d slot on the right next to the take-up lever, then into the third slot on the right in the guides just above th e needle clamp. Next slip the thread behind the meta l guide and then into the eye of the needle in B position, and then under what looks l ike a bridge at th e back of the foot. Pull the thread tail to the [...]

  • Page 9

    Lay thread through Orange tension disk, while holding the thre ad securely with both hands. Next slip in to guide directly below the tension from right to left. Slip the thread into the center slot and then up and over th e take-up lever slot.[...]

  • Page 10

    Slip the thread into the center slot next to the take-up lever, then into the center slot in the gu ides just ab ove the needle clamp. Next slip the thread b ehind the metal guide and then into the eye of the needle in A position, and then under what looks like a bridge at the back of th e foot . Pull the thr ead tail to the back of the serger. THR[...]

  • Page 11

    THREADING INFORMATION FOR A NARROW 5 THREA D SAFETY STITCH Threading the Green Upper Looper: Thread the top cover thread guide by slipping t he thread under the guide from right to left, and then pull t he thread under the small r ound disk from the right side.[...]

  • Page 12

    Lay thread through Green te nsion disk, while holding the thread securely with both hands. Next slip in to guide directly below the tension from right to left. Using tweezers slip the thread into the ne xt three guides mark ed with the small green dots.[...]

  • Page 13

    Thread the g uide that looks l ike a little pigt ail and then thread th rough the eye of the looper as shown. Pull th e thread tail to the back of the serger approximately 4 to 6 inches.[...]

  • Page 14

    Threading Red Lower Looper: Thread the to p thread guide by slip ping the thread under th e guide from right to left, and then pull the th read under the small round disk from the right side. Lay the thread through Red tension disk while holding the thre ad securely with both hands. Next slip in to guide directly below the tension from right to lef[...]

  • Page 15

    Using tweezers slip the thread into the slot at the back of the thread guide, a nd then into th e next th ree guides marked with the small red dots. Thread the eye of the looper as shown, maki ng sure that the thread is positioned in the “V” cut out in front of the looper. Pull the thread tail to the back of the serger approximately 4 to 6 inch[...]

  • Page 16

    Tugging slightly on the thread tail at the back of the serger, push threader lever all the way up to hook thread into the eye at the back of the looper. Threading Brown Chain Stitch Looper: Top Cover Thread Guide Thread the top cover thread guide by slipping the th read under the guide from right to left, and then pull the thre ad under the small r[...]

  • Page 17

    Lay thread through Brown tension disk, wh ile holding the thre ad securely with both hands. Next slip in to guide directly below the tension from right to left.[...]

  • Page 18

    Slip thread throug h front slot of threading guide. Using tweezers thread the next 4 guides identified with a small brown dot.[...]

  • Page 19

    Using the tweezers thread the last thread guide that is located on the left just below the looper. Next thread the br own looper eye from front to back, pulling thread over the top of the red looper, then pu ll the thread tail to the back of the serger 4 to 6 inches. Make sure the thread sits over the top of the “V” cut out just before the eye [...]

  • Page 20

    Threading Blue Overedge Stitch Needle: Top Cover Thread Guide Thread the top cover thread guide by slipping t he thread under the guide from right to left, and then pull t he thread under the small r ound disk from the right side. Lay thread through Blue tension disk, whil e holding the thread securely with both hands. Next slip into guide directly[...]

  • Page 21

    Slip the thread into the third slot clos est to the back and then up and over the take-up lever slot. Slip the thread into the thir d slot on the right next to the take-up lever, then into the third slot on the right in the guides just above th e needle clamp. Next slip the thread behind the meta l guide and then into the eye of the needle in (B) p[...]

  • Page 22

    Threading Orange Chain Stitch Needle: Top Cover Thread Guide Thread the top cover thread guide by slipping t he thread under the guide from right to left, and then pull t he thread under the small r ound disk from the right side. Lay thread through Orange tension disk, while holding the thre ad securely with both hands. Next slip in to guide direct[...]

  • Page 23

    Slip the thread into the center slot and then up and over th e take-up lever slot. Slip the thread into the center slot next to the take-up lever, then into the center slot in the guides just above the needle clamp. Next s lip the thread in front of the metal guide and then into the eye of the needle in (D) position, thro ugh the opening in the foo[...]

  • Page 24

    THREADING TIPS FOR 5-THREAD SAFETY STITCH: • Be sure to follow the thre ading sequence ou tlined above. • Make sure needles are se t-up in position s D, and B for 5-thread safety stitch. This is very well illust rated in your ma nual on page 15. • If you would prefer a wider 5-thread safety stitch, place the overedge needle in the A rather th[...]

  • Page 25

    THREADING INFORMATION FOR A TRIPLE COVER STITCH Disengage Moveable Upper Knife: Pull the holder (screw) as far as it will go to the right, a nd swing (turn) the knife down (counter-clockwise) until it clicks into resting posit ion. ( To re-engage knife, pull the holder out to the righ t and swing the knife up (clockwise) until it clicks into wor ki[...]

  • Page 26

    Disengage the Upper Loo per: In order to attach the Cover Plate, yo u must first disengage the upper looper. Turn handwheel towards you until t he rectan gular white knob is as far right at possible.[...]

  • Page 27

    To lower looper push the knob all the wa y to the left and th en push upwards. (To re-engage the loop er push the knob al l the way to the left and push it down. Turn your handwheel toward you to raise the looper.)[...]

  • Page 28

    Threading The Green Cover Stitch Needle: Top Cover Thread Guide Thread the top cover thread by slippi ng the thread unde r the guide from right to left, and then pull the th read under the small round disk from the right side.[...]

  • Page 29

    Lay thread through Green te nsion disk, while holding the thread securely with both hands. Next slip in to guide directly below the tension from right to left. Slip the thread into the thir d slot at the back and then into the take-up lever slot.[...]

  • Page 30

    Slip the thread into the third sl ot closest to the take-up lever. Slip thread through third slot on the right; next slip it in front of the thread guide and then into the eye of the needle (E) on the right. Finally th read the tail of the thread throug h the opening in the fo ot directly below the n eedle; pull thread under the foot and to th e ba[...]

  • Page 31

    Threading Blue Cover Stitch Needle: Top Cover Thread Guide Thread the top cover guide by sli pping th e thread under the gu ide from right to left, and then pull the th read under the small round disk from the right side.[...]

  • Page 32

    [...]

  • Page 33

    Slip the thread into the center slot. Slip thread through cen ter slot; next slip it in fron t of the thread guide and then into the eye of the center (D) needle. Finally thre ad the tail of the thread through the opening in the foot directly below the n eedle, pull thread under the foot and to the ba ck of the serger.[...]

  • Page 34

    Threading Orange Cover Stitch Needle: Top Cover Thread Gu ide Orange Needle Thread the top cover thread guide by slipping t he thread under the guide from right to left, and then pull t he thread under the small r ound disk from the right side.[...]

  • Page 35

    Lay thread through Orange tension disk, while holding the thre ad securely with both hands. Next slip in to guide directly below the tension from right to left. Slip thread into the first slot an d then into the take-up lever slot.[...]

  • Page 36

    Slip the thread into the first slot. Slip thread through first slot on the left; next slip it i n front of the thread guide and then into the eye of the (C) needle on the left. Finally thread the tail of the thread throug h the opening in the fo ot directly below the n eedle, pull thread under the foot and to th e back of the serger.[...]

  • Page 37

    Threading Red Lower Looper: Top Cover Thread Guide Thread the top cover thread guide by slipping t he thread under the guide from the right to left, and then pull t he thre ad under the small round disk from the right side.[...]

  • Page 38

    Lay thread through Red tensio n disk while holdin g the thread securely with both hands. Next slip into guide directly below the te nsion from right to left. Using tweezers slip the thread into the slot at the back of the thread guide, a nd then into the next 3 guides marked with small red dots.[...]

  • Page 39

    Thread the eye of th e lower looper as shown, maki ng sure that the thread is positioned in the V cut out in front of the looper threader. Pull the thread tail to the back of the serger approximately 4 to 6 inches. Tugging slightly on the thread tail at the back of the serger, push threader lever all the way up and to the left to hook the thread in[...]

  • Page 40

    Threading Brown Cover Stitch Looper: Top Cover Thread Guide Thread the top cover guide by sli pping th e thread under the gu ide fro m the rig ht to the left, and then pull the thread under the small round disk from the right side.[...]

  • Page 41

    Lay thread through Brown tension disk wh ile holding th e thre ad securely with both hands. Next slip in to guide directly below the tension from right to left. Slip thread thro ugh front slot of thread gu ide.[...]

  • Page 42

    Using the tweezers thread th e next 4 guides identified with a small brown dot . Using the tweezers thread the last thread guide that is located on the left just below the looper. Next thread the br own looper eye from front to back, pulling the thread over the top of the red looper, then pull t he th read tail to the back of the serger approximate[...]

  • Page 43

    Tugging slightly on the thread tail at the back of the serger, push threader lever all the way up and to the left to hook the thread into the eye at the back of the looper.[...]

  • Page 44

    Attaching Cover Stitch Plate: Remove the knife cover (overedge plate) by gently raising the lever as shown and pulling the cover towards you. Slip the Cover Stitch Plate onto the fron t cover by raising th e lever as shown and pushing the plate toward s the machine until it snaps into place.[...]

  • Page 45

    In order for the Cover Stitch Plate to si t properly, you must set the seam width finger to the “R” position. TIPS FOR TRIPLE COVER STITCH • Be sure to follow the thread ing sequence outl ined above. • Make sure needles are set- up in positions C, D, and E for the Triple Cover Stitch. This is very well illust rate d in the manual on page 15[...]

  • Page 46

    HOW TO DISENGAGE THE MOVAB LE UPPER KNIFE Disengage Movable Upper Knife: Pull the holder (screw) as fa r as it will go to the righ t, and swing the knife down until it clicks into the r esting position. (To re-engage the knife, pull the holder to th e right and swing th e knife up until it clicks into the working position.)[...]

  • Page 47

    HOW TO CONVERT THE GREEN UPPER LOOPER TO A SPREADER To produce the following stitches you must convert the uppe r looper to a spreader . • 2-Thread Wrapped Edge Ov erlock • 2-Thread Overedge • 3-Thread Ultra Stretch Mo ck Safety Stitch • 4-Thread Safety Stitch Push white spreader l ever up so that spreader sli ps into the eye of the looper.[...]

  • Page 48

    HOW TO DISENGAGE UPPER (GREEN) LOOP ER Turn handwheel towards you until t he whit e rectangular knob is as far to the right as possible. To lower the looper push the knob all th e way to the left an d then pus h it up. (To re-engage the loop er push the knob al l the way to the left and push it down. Turn the handwheel towards you to raise the loop[...]