Snapper S200XKAV2561 manuel d'utilisation
- Voir en ligne ou télécharger le manuel d’utilisation
- 49 pages
- 4.14 mb
Aller à la page of
Les manuels d’utilisation similaires
-
Lawn Mower
Snapper 3312X6S
36 pages 1.33 mb -
Lawn Mower
Snapper 4111X5S
8 pages 0.68 mb -
Lawn Mower
Snapper MZM2300KH
56 pages 2.89 mb -
Lawn Mower
Snapper SPE152KW, SPE132KW, SPE361, SPE481
36 pages 1.52 mb -
Lawn Mower
Snapper EFRP216516TV
25 pages 0.52 mb -
Lawn Mower
Snapper ODP21400
12 pages 0.82 mb -
Lawn Mower
Snapper MR216015T
28 pages 0.66 mb -
Lawn Mower
Snapper ELP21600
14 pages 1.36 mb
Un bon manuel d’utilisation
Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Snapper S200XKAV2561. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Snapper S200XKAV2561 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.
Qu'est ce que le manuel d’utilisation?
Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Snapper S200XKAV2561 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.
Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.
Donc, ce qui devrait contenir le manuel parfait?
Tout d'abord, le manuel d’utilisation Snapper S200XKAV2561 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Snapper S200XKAV2561
- nom du fabricant et année de fabrication Snapper S200XKAV2561
- instructions d'utilisation, de réglage et d’entretien de l'équipement Snapper S200XKAV2561
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes
Pourquoi nous ne lisons pas les manuels d’utilisation?
Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Snapper S200XKAV2561 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Snapper S200XKAV2561 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Snapper en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Snapper S200XKAV2561, comme c’est le cas pour la version papier.
Pourquoi lire le manuel d’utilisation?
Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Snapper S200XKAV2561, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.
Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Snapper S200XKAV2561. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.
Table des matières du manuel d’utilisation
-
Page 1
5101090 Revision C Rev . Date: 9/2007 TP 100-7332-C-M2-SP Briggs & Stratton Y ard Power Products Group 5375 North Main Street Munnsville, NY 13409 800-933-6175 S200X Series Zero-T urn Riding Mower OPERA TOR’S MANUAL Model Number: Description 5900664 S200XKA V2561, 25HP Kawasaki, 61” Cut Zero-T urn Riding Mower 5900692 S200XKOH2761, 27HP Koh[...]
-
Page 2
W ARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects, or other reproductive harm. Thank you for pur chasing this quality-built Snapper Pro product. We’re pleased that you’ve placed your confidence in the Snapper Pro brand. When operated and maintained according to the [...]
-
Page 3
T able of Contents Operator Safety .....................................................2 Safety Rules and Information ...........................................2 Safety Decals ..................................................................11 Safety Interlock System ..................................................12 Features & Controls ..[...]
-
Page 4
2 www .SnapperPro.com Safety Operator Safety OPERA TING SAFETY Congratulations on purchasing a superior -quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety . Do not operate this machine unless you have been trained. Reading and understanding this operator’ s m[...]
-
Page 5
3 Safety Operator Safety SLOPE OPERA TION Operation on slopes can be dangerous. Using the unit on a slope that is too steep where you do not have adequate wheel traction (and control) can cause sliding, loss of steering, control, and possible rollover . Y ou should not operate on a slope greater than a 5.4 foot rise over a 20 foot length (15 degree[...]
-
Page 6
4 www .SnapperPro.com Safety ROLL BAR USE Keep the roll bar in the raised position and fasten the seat belt. There is no roll over protection when the roll bar is down! Do not jump off if the mower tips (it is safer to be secured by the seat belt with the roll bar raised.) Lower the roll bar only when necessary (such as to temporarily clear a low o[...]
-
Page 7
5 Safety Operator Safety ENCLOSED AREAS Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers. The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death. FUEL AND MAINTENANCE Always disengage all drives, shutoff the engine, a[...]
-
Page 8
6 www .SnapperPro.com Safety 2. Mow only in the daylight or with good artificial light, keeping away from holes and hidden hazards. 3. Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’ s position. Use seat belts if provided. 4. Be sure of your footing while using pedestrian[...]
-
Page 9
7 Safety Operator Safety spark arrester . It is a violation of California Public Resource Code Section 4442 to use or operate the engine on or near any forest-covered, brush-covered, or grass-covered land unless the exhaust system is equipped with a spark arrester meeting any applicable local or state laws. Other states or federal area may have sim[...]
-
Page 10
8 www .SnapperPro.com Safety Operator Safety SERVICE AND MAINTENANCE T o avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline co[...]
-
Page 11
9 Safety Operator Safety 27. Models equipped with an engine radiator: WARNING: Stored energy device. T o prevent serious bodily injur y from hot coolant or steam blow-out, never attempt to remove the radiator cap while the engine is running. Stop the engine and wait until it is cool. Even then, use extreme care when removing the cap. ROLL BAR INSTR[...]
-
Page 12
10 www .SnapperPro.com Safety INSPECT BUCKLE & LA TCH INSPECT WEBBING Operator Safety W ARNING Failure to properly inspect and maintain the seat belt can cause serious injury or death. INSPECTION AND MAINTENANCE OF THE ROLL BAR SEA T BEL T • The seat belt like the ROLL BAR, needs to be periodically inspected to verify that the integrity has n[...]
-
Page 13
Safety Operator Safety 11 Safety Decals This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing. Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate thi[...]
-
Page 14
12 www .SnapperPro.com Safety Operator Safety Safety Interlock System This unit is equipped with safety interlock switches. These safety systems are present for your safety , do not attempt to bypass safety switches, and never tamper with safety devices. Check their operation regularly . Operational SAFETY Checks T est 1 — Engine should NOT crank[...]
-
Page 15
13 Safety Operator Safety Identification Numbers S S A A M M P P L L E E When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers. Record your part number , serial number and engine serial numbers in the space provided on the inside front cover for easy access. These numbers can be found in t[...]
-
Page 16
14 www .SnapperPro.com Controls Control Functions The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. T o learn what combination and sequence of controls to use for various tasks see the OPERA TION section. Gr[...]
-
Page 17
Fuel T ank Cap T o remove the cap, turn counterclockwise. Fuel Level Gauge Displays the fuel level in the tank. Features & Controls 15 Controls Parking Brake DISENGAGE Releases the parking brake. ENGAGE Locks the parking brake. Pull the parking brake lever back to engage the parking brake. Move the lever fully forward to disengage the parking b[...]
-
Page 18
16 www .SnapperPro.com Operation General Operating Safety Before first time operation: • Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower . • Become familiar with all of the controls and how to stop the unit. • Drive in an open area without mowing to become accustomed to [...]
-
Page 19
Operation 17 Operation Figure 4. Seat Adjustment A. Seat Adjustment Lever Seat Adjustment See Figure 4. The seat can be adjusted forward and backward. Move the lever towards the left, position the seat as desired, and release the lever to lock the seat into position. Tire Pressure Front 25 psi (1,72 bar) Rear 15 psi (1,03 bar) Figure 3. Checking Ti[...]
-
Page 20
18 www .SnapperPro.com Operation Operation Foot Pedal Adjustment The deck lift foot pedal can be adjusted to accommodate the operator’ s height for optimal comfort. T o adjust pedal position: 1. Remove the foot pedal (A, Figure 7) from the pedal mount tab (B). 2. Remove the pedal mount hardware (C) and rotate the tab 180 degrees. 3. Reinstall the[...]
-
Page 21
19 Operation Figure 8. Raise & Lower the Roll Bar A. Hair Pin Clip B. Retainer Pin C. Roll Bar D. Rubber Stop Raise and Lower the Roll Bar T o Lower the Roll Bar: 1. Pull the hair pin clips (A, Figure 8) out of the retainer pins (B). 2. Push or pull the top of the roll bar (C) forward against the rubber stops (D) and remove the retainer pins (B[...]
-
Page 22
20 www .SnapperPro.com Operation Operation Starting the Engine 1. While sitting in the operator’ s seat, engage the parking brake by pulling the parking brake lever back, make sure the PTO switch is disengaged (pressed down fully) and the motion control handles are locked in the NEUTRAL position. 2. NOTE: A warm engine may not require choking. Se[...]
-
Page 23
21 Operation Zero T urn Driving Practice The lever controls of the Zero T urn rider are responsive, and learning to gain a smooth and efficient control of the rider’ s forward, reverse, and turning movements will take some practice. Spending some time going through the maneuvers shown and becoming familiar with how the unit accelerates, travels, [...]
-
Page 24
22 www .SnapperPro.com Operation Operation Executing an End-Of-Row Zero T urn Y our Zero T urn Rider’ s unique ability to turn in place allows you to turn around at the end of a cutting row rather than having to stop and Y -turn before starting a new row . For example, to execute a left end-of row zero turn: 1. Slow down at the end of the row . 2[...]
-
Page 25
23 Safety Controls Operation Maintenance T roubleshooting Specifications Mowing 1. Engage the parking brake. Make sure the PTO switch is disengaged, the motion control levers are locked in the NEUTRAL position and the operator is on the seat. 2. Start the engine (see Starting The Engine ). 3. Set the mower cutting height (see Mowing Height Adjustme[...]
-
Page 26
24 www .SnapperPro.com Operation Operation When and How Often to Mow The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: 1. Mow when the grass is between three and five inches high. 2. Mow with sharp blades. Short clippings of grass one inch or shorter decomp[...]
-
Page 27
25 Operation Figure 19. T railer Weight Recommendations A. Clevis Pin B. Clip Attaching A T railer The maximum weight of a towed trailer should be less than 200 lbs (91kg). Secure the trailer with a appropriately sized clevis pin (A, Figure 19) and clip (B). Excessive towed loads can cause loss of traction and loss of control on slopes. Reduce towe[...]
-
Page 28
26 www .SnapperPro.com Maintenance Maintenance Schedule The following schedule should be followed for normal care of your rider and mower . Y ou will need to keep a record of your operating time. Determining operating time is easily accomplished by observing the elapsed time recorded by the hour meter . Safety Items Before Each Use Every 5 Hours Ev[...]
-
Page 29
27 Maintenance Checking / Adding Fuel T o add fuel: 1. Remove the fuel cap. 2. Fill the tank to about 1-1/2” (3,81 cm) of the bottom of the filler neck. This will allow for fuel expansion. NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations. 3. Install and hand tighten the fuel cap. Fuel Filter The fuel filter is [...]
-
Page 30
28 www .SnapperPro.com Maintenance Regular Maintenance Lubrication Lubricate the unit at the locations shown in Figures 21 through 24 as well as the following lubrication points. Grease: • front caster wheel axles & yokes • deck lift pivot blocks • mower deck spindles • mower deck idler arm Use grease fittings when present. Disassemble [...]
-
Page 31
29 Maintenance Regular Maintenance Figure 26. Battery Compartment A. Hydraulic Oil Reservoir B. Hydraulic Oil Filter Figure 25. Checking Hydraulic Oil Level A. Hydraulic Oil Reservoir B. Reservoir Cap A B Check Hydraulic Oil Level 1. Before removing the reservoir cap, make sure the area around the reservoir cap and fill neck of the reser voir is fr[...]
-
Page 32
30 www .SnapperPro.com Maintenance Regular Maintenance Servicing The Mower Blades Removing the Mower Blade 1. T o remove the mower blade, use a 1” wrench on the flats of the spindle shaft and remove the mower blade mounting bolt with a 15/16” wrench (Figure 27). 2. If there are no flats on the spindle shaft, wedge a wooden block between the mow[...]
-
Page 33
31 Maintenance Figure 32. Tightening the Mower Blade for Installation A. Mower Blade Mounting Bolt B. Flat Washer C. Mower Blade Air Lift (Points Up For Installation) D. 4 X 4 Wooden Block D A B Sharpening the Mower Blade 1. Sharpen the mower blades with grinder , hand file, or electric blade sharpener . 2. Sharpen the mower blade by removing an eq[...]
-
Page 34
32 www .SnapperPro.com Maintenance Ground Speed Control Lever Adjustment The control levers can be adjusted in three ways. The alignment of the control levers, the placement of the levers (how close the ends are to one another) and the height of the levers can be adjusted. T o Adjust the Handle Alignment Loosen the mount bolts (A, Figure 33) and pi[...]
-
Page 35
33 Maintenance 2" - 2-1/ 8 " (5,0 - 5,4cm) Figure 36. Parking Brake Adjustment A. Brake Spring B. Adjustment Nut Parking Brake Adjustment 1. Disengage the PTO, stop the engine, block the front wheels, remove the ignition key , and engage the parking brake. 2. Locate the brake spring (A, Figure 36). 3. With the parking brake engaged, measu[...]
-
Page 36
34 www .SnapperPro.com Maintenance Return-T o-Neutral Adjustment T o determine if it is necessar y to adjust the neutral return, perform the following steps. 1. Disengage the PTO, engage the parking brake and turn off the engine. 2. Move the ground speed control levers into the operating position, pull levers rearward and release. 3. Move the groun[...]
-
Page 37
35 Maintenance Figure 38. Check Lift Rod Timing Figure 39. Adjust Lift Rod Timing Figure 40. 2 x 4 Locations Figure 41. Hanger Chain Adjustment Regular Maintenance Deck Rod Timing Adjustment 1. Park the machine on a flat, level surface. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key . Rear tires must b[...]
-
Page 38
36 www .SnapperPro.com Maintenance Regular Maintenance Figure 43. Mower PTO Belt Routing A. Spindle Pulley B. PTO Drive Belt C. Spring-loaded Idler Pulley D. Stationary Idler Pulley B A Figure 42. Mower PTO Belt A. Idler Arm B. Stationary Idler Pulley C. Nut B Mower Belt Replacement 1. Park the tractor on a smooth, level surface such as a concrete [...]
-
Page 39
37 Maintenance 8 3/8” (21,2 cm) Figure 44. Hydraulic Pump Drive Belt Replacement A. Pump Drive Belt B. Crankshaft Pulley C. Pump Pulley D. Idler Pulley E. Idler Arm F . Spring G. Spring Anchor Eyebolt B D A C F G E C Hydraulic Pump Drive Belt Replacement 1. Park the tractor on a smooth, level surface such as a concrete floor . Disengage the PTO, [...]
-
Page 40
38 www .SnapperPro.com Maintenance Regular Maintenance Figure 45. Battery Compartment A. Positive (+) Cable & T erminal B. Negative (-) Cable & T erminal Battery Maintenance NOTE: This unit is equipped with a maintenance-free BCIU1 battery . Cleaning the Battery and Cables 1. Disconnect the cables from the battery , negative (black) cable f[...]
-
Page 41
39 Maintenance Battery Ser vice Checking Battery Voltage A voltmeter can be used to determine condition of battery . When engine is off, the voltmeter shows battery voltage, which should be 12 volts. When engine is running, the voltmeter shows voltage of charging circuit which normally is 13 to 14 volts. A dead battery or one too weak to start the [...]
-
Page 42
40 www .SnapperPro.com Maintenance Regular Maintenance To Starter Switch Starting V ehicle Battery T o Gr ound To Starter Switch Dischar g ed V ehicle Battery Engine Block THIS HOOK-UP FOR NEGA TIVE GR OUND VEHICLES MAKE CERT AIN VEHICLES DO NO T T OUCH Jumper Cab le Jumper Cab le W ARNING Any procedure other than the preceding could result in: (1)[...]
-
Page 43
41 Maintenance Storage T emporar y Storage (30 Days Or Less) Remember , the fuel tank will still contain some gasoline, so never store the unit indoors or in any other area where fuel vapor could travel to any ignition source. Fuel vapor is also toxic if inhaled, so never store the unit in any structure used for human or animal habitation. Here is [...]
-
Page 44
42 www .SnapperPro.com T roubleshooting T roubleshooting Chart While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be per formed to allow it to continue operating properly . The troubleshooting guide below lists the most common problems, their causes and rem[...]
-
Page 45
43 T roubleshooting Rider T roubleshooting Continued. Problem Cause Remedy Engine runs, but rider will 1. Hydraulic release valve(s) 1. T urn valve(s) clockwise to close. not drive. in “open” position. 2. Belt is broken. 2. See Drive Belt Replacement. 3. Drive belt slips. 3. See problem and cause below . 4. Brake is not fully released. 4. See a[...]
-
Page 46
44 www .SnapperPro.com T roubleshooting T roubleshooting Common Cutting Problems Problem Cause Remedy Streaking. 1. Blades are not sharp. 1. Sharpen your blades. 2. Blades are worn down to far . 2. Replace your blades. 3. Engine speed is too slow . 3. Always mow at full throttle. 4. Ground speed is too fast. 4. Slow down. 5. Deck is plugged with gr[...]
-
Page 47
45 Specifications ENGINE: 25 HP Kawasaki Make Kawasaki Model FH721V Horsepower 25 @ 3600 rpm Displacement 41.2 Cu. in (675 cc) Electrical System 12 Volt, 13 amp. Alternator , Battery: 340 CCA Oil Capacity 2.0 US qt. ( 1.9 L) w/ Filter 27 HP Kohler Make Kohler Model CV740S Horsepower 27 @ 3600 rpm Displacement 44.24 Cu. in (725 cc) Electrical System[...]
-
Page 48
Thank you f or purchasing Ferris commercial mowing equipment. Please take a f ew minutes to read this limited w arranty information. It contains all the information you will need to ha ve your F erris mower repaired in the unlikely e vent that a breakdo wn covered by this limited warranty should occur . Owner's Responsibilities - As a conditio[...]
-
Page 49
Briggs & Stratton Y ard Power Products Group 5375 North Main Street Munnsville, NY 13409 800-933-6175 www .SnapperPro.com ENGINE: 25 HP Kawasaki Make Kawasaki Model FH721V Oil Capacity 2.0 US pt. ( 1.9 L) w/ Filter 27 HP Kohler Make Kohler Model CV740S Oil Capacity 2.2 pt. (2.0 L) w/ Filter 27 HP Kawasaki Make Kawasaki Model FX751V Oil Capacity[...]