Sony DVW-M2000 manuel d'utilisation

OPERA TION MANUAL [English] 1st Edition (Revised 2) DIGIT AL VIDEOCASSETTE RECORDER DV W -M2000 DV W -M2000P DV W -2000 DV W -2000P TM Note The supplied CD-ROM includes operation manuals for the DVW-2000 series of digital videocassette recorders (English, Japanese, French and German versions). For more details, see page 1-5 “Using the CD-ROM Manu[...]

W ARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. A VER TISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humi[...]

AVERTISSEMENT: CET AVERTISSEMENT EST VALABLE POUR LES AUTRES PAYS. 1. Utiliser un cordon d’alimentation approuvé (conducteur d’alimentation 3 âmes)/connecteur d’appareil/prise avec contacts de mise à la terre conforme aux règles de sécurité de chaque pays si applicable. 2. Utiliser un cordon d’alimentation approuvé (conducteur d’al[...]

Table of Contents 1 Ta b le of Contents Chapter 1 Overview Chapter 2 Location and Function of Pa r t s Chapter 3 Preparations Chapter 4 Recor ding and Pla yback 1-1 F eatures ........................................................................................... 1-1 1-2 Example System Conf iguration .............................................[...]

Ta b le of Contents 2 Table of Contents Chapter 5 Editing (Continued) Chapter 6 Shot Mark Function Chapter 7 T ele-File 5-2 DMC Editing ................................................................................. 5-11 5-2-1 Overvie w of DMC Editing ................................................... 5-11 5-2-2 Carrying Out DMC Editing ........[...]

Table of Contents 3 6-1 Chapter 12 Setup Menus Chapter 14 Maintenance and Inspection 11-1 Over view of the Function Menu ............................................... 11-1 11-1-1 Function Menu Conf iguration ........................................... 11-1 11-1-2 Using the Function Menu .................................................. 11-2 11-2[...]

Chapter 1 Overview Chapter 1 Overview 1-1 1-1 Features Chapter 1 Overview The DVW-M2000/M2000P/2000/2000P is a digital videocassette recorder based on the digital Betacam format. This unit uses large scale integrated circuits for signal processing, and has a simple internal construction, allowing it to provide functionality at least equivalent to a[...]

1-1 Features Chapter 1 Overview 1-2 Chapter 1 Overview High-performance heads and compatibility playback function The newly developed high-performance heads and dynamic tracking (DT) technology provide high- density recording and playback in narrow tracks with high reliability. In addition to the digital Betacam recording and playback heads, this u[...]

Chapter 1 Overview Chapter 1 Overview 1-3 High quality variable speed playback and digital jog sound function In digital Betacam or MPEG IMX format 1) playback, the dedicated playback DT heads allow smooth, noiseless playback from –1 to +3 times normal speed. In analog Betacam compatible playback also, similar dedicated DT heads allow noiseless p[...]

1-1 Features Chapter 1 Overview 1-4 Chapter 1 Overview 1-2 Example System Configuration The following conceptual diagram shows an example of use. Digital/analog cassette BVE-series editor Tape control Analog composite Audio monitor Microphone Analog composite/component DVW-M2000/M2000P/2000/2000P Video monitor VTR with SDI connectors or analog VTR [...]

Chapter 1 Overview Chapter 1 Overview 1-5 1-3 Using the CD-R OM Manual The supplied CD-ROM includes operation manuals for the DVW-2000 series of digital videocassette recorders (English, Japanese, French, and German versions). 1-3-1 CD-R OM System Requirements The following are required to access the supplied CD- ROM disc. •C omputer: PC with Int[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-1 2-1 Contr ol P anels Chapter 2 Location and Function of P ar ts There are three control panels, as follows: •U pper control panel • Lower control panel •S witch panel VID. IN PB/EE CONFI CTL/TC Y-R,B PB OFF TC MENU TCGSET ON OFF KEY INHI FRONT REAR P ANEL SE[...]

2-1 Contr ol P anels Chapter 2 Location and Function of Parts 2-2 Chapter 2 Location and Function of Parts 2-1-1 Upper Contr ol Panel Z BET ACAM/SP 1(9P) 2(50P) RS-232C BET ACAM SX MPEG IMX Digital BET ACAM POWER PHONES REMOTE EJECT 1 POWER switch 2 REMOTE buttons and RS-232C indicator 4 Format indicators 5 PHONES jack and control Cassette compartm[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-3 VID. IN PB/EE CONFI CTL/TC Y-R,B PB OFF TC MENU TCGSET VID. IN PB/EE CONFI CTL/TC Y-R,B PB OFF TC MENU TCGSET 1 Audio control section (see page 2-4) 2 CHANNEL CONDITION indicator (see page 2-6) 3 Menu control buttons (see page 2-6) 4 Time data/menu display section[...]

2-1 Contr ol P anels Chapter 2 Location and Function of Parts 2-4 Chapter 2 Location and Function of Parts 1 Audio control section In the audio control section, you can select and display input and output signals for audio channels. 1 Audio selection function selector buttons INPUT (input signal selection mode) button: Pressing this button puts the[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-5 AES/EBU/ANA SDI DATA 5 6 7 8 MIX 1 2 3 4 OVER dB dB EMPH L R 20 10 2 1 0 0 -10 -20 -30 -40 -60 -1 -10 -20 -40 -2 Input signal indicator DATA indicator MIX indicator OVER indicator Level meter Input channel indicator Monitor channel L and R indicators EMPH indicato[...]

2-1 Contr ol P anels Chapter 2 Location and Function of Parts 2-6 Chapter 2 Location and Function of Parts Note Before selecting signals from two input channels for recording in one recorder channel, check to be sure that the emphasis settings (ON or OFF) of the two input channels are the same. Recording and playback of mixed signals cannot be carr[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-7 If there is no setting displayed in the lower line of the menu display, even though a menu item is displayed in the upper line, pressing the corresponding function button moves to a lower menu level. Overview of the function menu The function menu provides conveni[...]

2-1 Contr ol P anels Chapter 2 Location and Function of Parts 2-8 Chapter 2 Location and Function of Parts CONFI (ON)/PREREAD indicators These indicate the state of the VTR CONFI playback 1) function. When the CONFI playback function is enabled by the setting in function menu HOME page, the CONFI indicator appears, and when CONFI playback is actual[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-9 1 SHUTTLE button To use the search dial for playback in shuttle mode, press this button, turning it on. For details of playback in shuttle mode, see the description of the search dial 5 . 2 JOG button To use the search dial for playback in jog mode, press this but[...]

2-1 Contr ol P anels Chapter 2 Location and Function of Parts 2-10 Chapter 2 Location and Function of Parts PREROLL REW PLAY F FWD STOP REC EDIT STANDBY 8 REC INHI (recording inhibit) indicator This indicator is on or off according to the combination of the F5 (RECINH) setting on function menu page 4 and the record inhibit plug on the cassette, as [...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-11 5 STOP button To stop recording or playback, press this button, turning it on. When you stop playback, the unit switches either to still playback or to E-E mode according to the setting on function menu HOME page for F2 (PB/EE) and the setting of setup menu item [...]

2-1 Contr ol P anels Chapter 2 Location and Function of Parts 2-12 Chapter 2 Location and Function of Parts ENTRY IN OUT IN OUT AUDIO PREVIEW REVIEW AUTO EDIT DELETE MEMORY TRIM DMC EDIT KEY INHI (inhibit) indicator This indicator lights when the KEY INHIBIT switch on the switch panel (see page 2-14) is set to ON. qs PLAYER button and RECORDER butt[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-13 LIST GOOD SHOT MARK REC/ ERASE ENTRY button: Use this for setting edit points and so on. • To set a video IN point or OUT point: Hold down the IN button or OUT button, and press this button. • To set an audio IN point or OUT point: Hold down the AUDIO IN butt[...]

2-1 Contr ol P anels Chapter 2 Location and Function of Parts 2-14 Chapter 2 Location and Function of Parts 2-1-3 Switch P anel To access the switch panel, open the lower control panel. On how to open the lower control panel, see the figure on page 2-1. ON OFF KEY INHI FRONT REAR P ANEL SEL CONTROL P ANEL 2 KEY INHIBIT switch 3 PANEL SELECT switch [...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-15 2 AUDIO INPUT CH1 to CH4 (channels 1 to 4) and CUE IN LEVEL switches Set these for each channel as shown in the following table, according to the audio/cue input level to the AUDIO INPUT CH1 to CH4 and CUE IN connectors and the impedance. AUDIO INPUT CH1 to CH4 a[...]

2-2 Connector P anel Chapter 2 Location and Function of Parts 2-16 Chapter 2 Location and Function of Parts 2 Analog video input/output section 1 REF. (reference) VIDEO INPUT connectors (BNC type) and 75 Ω termination switch Input a reference video signal. Input a video signal with chroma burst (VBS) or a monochrome video signal (VS). When using [...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-17 4 Digital signal input/output section 1 SDI (Serial Digital Interface) INPUT connectors (BNC type) Input D1 format digital video/audio signals. Of the two connectors, the upper one is for input, and the lower one is for an active-through connection. 2 SDI (Serial[...]

2-2 Connector P anel Chapter 2 Location and Function of Parts 2-18 Chapter 2 Location and Function of Parts 2 CONTROL PANEL connector (round type, 10- pin) In addition to the lower control panel, a similar control panel can be connected to this unit. To connect such a second control panel, use this connector. When two control panels are connected, [...]

Chapter 3 Preparations 3-1 Chapter 3 Preparations Chapter 3 Preparations 3-1 Connections to External De vices 3-1-1 Connections to Digital Devices This unit can input serial digital signals (video and audio) from another digital VTR such as the MSW- A2000/A2000P/M2000/M2000P/2000/2000P and DVW-A500/A500P/500/500P. The following example shows the co[...]

3-1 Connections to External Devices 3-2 Chapter 3 Preparations Chapter 3 Preparations 3-1-2 Connections to Analog De vices The following example shows the connections with an analog VTR (a Betacam SP VTR, D2 VTR, 1-inch VTR, etc.) for recording analog audio and video signals. A UDIO OUTPUT CH1 to CH4 A UDIO OUTPUT CH1 to CH4 VIDEO OUTPUT COMPOSITE [...]

Chapter 3 Preparations 3-3 Chapter 3 Preparations 3-2 Reference Signals f or Video Output and Serv o System This section describes how reference signals for the video output signals and servo system are selected. The output from the internal reference video signal generator is supplied to the output video signal and servo circuits as a reference si[...]

3-2 Reference Signals f or Video Output and Servo System Chapter 3 Preparations 3-4 Chapter 3 Preparations 3-2-2 Reference Signal f or the Servo System The VTR automatically selects either the input video signal or the output from the internal reference video signal generator as the reference signal for the servo system. Which of the two signals is[...]

Chapter 3 Preparations Chapter 3 Preparations 3-5 Connections for recording from an external VTR (player) 3-2-3 Connecting Reference Signals Connect reference signals as shown below, according to the way in which the unit is to be used. Connections for recording from a switcher or signal generator 75 Ω 75 Ω SDI INPUT REF . VIDEO INPUT SDI OUTPU[...]

3-2 Reference Signals f or Video Output and Servo System Chapter 3 Preparations 3-6 Chapter 3 Preparations Connections for playback • SDI OUTPUT • COMPOSITE • COMPONENT REF . VIDEO INPUT 75 Ω 75 Ω Reference signal Video monitor DVW-M2000/M2000P/2000/2000P 75 Ω termination switch: ON[...]

Chapter 3 Preparations Chapter 3 Preparations 3-7 3-3 Setup The principal setup operations before operating this unit can be carried out using setup menus. The setup menus of this unit comprise a basic setup menu and an extended setup menu. The contents of these menus are as follows. Basic setup menu: • Items relating to the hours meter • Items[...]

3-2 Reference Signals f or Video Output and Servo System Chapter 3 Preparations 3-8 Chapter 3 Preparations TC R . 2 3 : 5 9 . 4 0 . 1 8 * PS H U T T L E S T I L L 3-4 Superimposed Character Inf ormation When the function menu item CHARA is set to ON, the video signal output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector or the SDI OUTPUT 3 (SU[...]

Chapter 3 Preparations Chapter 3 Preparations 3-9 2 Time code reader drop frame mark (for 525-line mode only) “.”: Indicates drop frame mode “:”: Indicates non-drop-frame mode 3 Time code generator drop frame mark (for 525- line mode only) “.”: Indicates drop frame mode (factory preset) “:”: Indicates non-drop-frame mode 4 VITC fiel[...]

3-2 Reference Signals f or Video Output and Servo System Chapter 3 Preparations 3-10 Chapter 3 Preparations 3-5 Cassettes 3-5-2 Inser ting and Ejecting Cassettes It is not possible to insert or eject a cassette unless the unit is powered on. Inserting a cassette 1 Turn the POWER switch on. 2 Check the following points, then insert the cassette in t[...]

Chapter 3 Preparations Chapter 3 Preparations 3-11 Removing slack from the tape Press in one of the reels with a finger, and turn gently in the direction shown by the arrows until there is no slack in the tape. Ejecting a cassette Press the EJECT button. Note Ejecting is a local operation. It is not possible to eject a cassette in another unit by r[...]

3-2 Reference Signals f or Video Output and Servo System Chapter 3 Preparations 3-12 Chapter 3 Preparations 3-6 Using a Memory Stick When a Memory Stick (option) is inserted in the VTR, the file data can be stored on the Memory Stick , which enables you to share data among VTRs. Inserting a Memory Stick Insert a Memory Stick with the label side up [...]

Chapter 3 Preparations Chapter 3 Preparations 3-13 Notes • Prevent metallic objects or your finger from coming into contact with the terminal of the connecting section. •D o not attach any material other than the supplied label to the label space. •A ttach the label at the prescribed labeling position. Make sure the label is attached at the l[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-1 Chapter 4 Recor ding and Pla ybac k 4-1 Recor ding This section describes video and audio recording on the unit. 4-1-1 Preparations f or Recor ding Switch and menu settings Before beginning recording, make necessary switch and menu settings. For details on each setting, see the p[...]

4-1 Recor ding Chapter 4 Recording and Playback 4-2 Chapter 4 Recording and Playback Adjusting the audio recording levels When carrying out audio recording at a reference level Leave the REC controls pressed in. The audio signals will be recorded at a preset reference level (a reference 0 dB indication for an input of +4 dBm). Manually adjusting th[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-3 Setting an initial time code value Use the following procedure. 1 Set the CTL/TC to TC. 2 Press the F6 (TCGSET) button. The function menu display changes as follows. SET EXIT TCG SET 00 : 00 : 00 : 00 The first digit of the time code value (8 digits: hours, minutes, seconds, and [...]

4-1 Recor ding Chapter 4 Recording and Playback 4-4 Chapter 4 Recording and Playback To synchronize the internal time code generator to an external signal Use this method to synchronize the time code generators of a number of VTRs, or to record the playback time code signal from an external VTR without deterioration of the signal waveform. In this [...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-5 To record an external time code without modification Using this method has no effect on the running of the internal time code generator. To record the playback time code from an external VTR, the method under the heading above, “To synchronize the internal time code generator t[...]

4-1 Recor ding Chapter 4 Recording and Playback 4-6 Chapter 4 Recording and Playback 4-2 Pla ybac k This section describes playback of video and audio. 4-2-1 Preparations f or Playbac k Switch and menu settings Before beginning playback, make necessary switch and menu settings. For details on each setting, see the pages indicated in parenthesis. VI[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-7 Time data selection Displayed time data Use the CTL/TC setting in function menu HOME page to select one of CTL (control), time code, and user bit values. When you select time code, the data displayed is determined by the TCR setting (LTC/AUTO/VITC) in function menu page 1 as foll[...]

4-2 Pla ybac k Chapter 4 Recording and Playback 4-8 Chapter 4 Recording and Playback Playback in jog mode In jog mode, you can control the speed of playback by the speed of turning the search dial. The playback speed range is ±1 times normal speed. The playback speed range can be ±3 times normal speed by changing the setting of setup menu item 11[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-9 To alternate between normal-speed playback and shuttle mode playback Set the search dial to the position corresponding to the desired shuttle playback speed, then switch between normal-speed playback and shuttle playback by pressing the PLAY and SHUTTLE buttons alternately. For i[...]

4-2 Pla ybac k Chapter 4 Recording and Playback 4-10 Chapter 4 Recording and Playback 2 When the adjustment is completed, release the PLAY button. The tape transport returns to normal speed, and the SERVO indicator comes on again. To perform continuous capstan override playback 1 Set setup menu item 111 (TSO PLAY) to TSO. 2 Hold down the DMC EDIT b[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-11 4-2-3 Dynamic Motion Contr ol (DMC) Playbac k DMC playback allows you to vary the playback speed for a certain section of a tape, in variable speed mode (from –1 to +3 times normal speed for digital Betacam playback, from –1 to +3 times normal speed for MPEG IMX playback, fr[...]

4-2 Pla ybac k Chapter 4 Recording and Playback 4-12 Chapter 4 Recording and Playback 4 Holding down the DMC EDIT button, turn the search dial, to set the initial speed at the playback start point. The speed you set appears in the speed indication area. During this period the tape does not move. When the initial speed setting is complete, release t[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-13 To start playback immediately after preroll Press the PREVIEW button. The PREVIEW button lights, and after preroll, DMC playback is carried out for the section from the speed variation start point, then playback continues at normal speed from the speed variation end point. To st[...]

Chapter 5 Editing Chapter 5 Editing 5-1 Chapter 5 Editing 5-1 A utomatic Editing This section describes how to carry out automatic editing with this unit and another VTR connected to the REMOTE1-IN(9P) connector. 5-1-1 Overview Editing mode •A ssemble editing This is the editing mode in which successive portions of the edited result are recorded [...]

5-1 A utomatic Editing Chapter 5 Editing 5-2 Chapter 5 Editing 5-1-2 Switch and Men u Settings VID. IN PB/EE CONFI CTL/TC Y-R,B PB OFF TC MENU TCGSET Z Z VID. IN PB/EE CONFI CTL/TC Y-R,B PB OFF TC MENU TCGSET Z POWER switch: ‘ ( ’ side (ON) Audio selection function selector buttons (see page 2-4) : Select the input audio signal. Recorder settin[...]

Chapter 5 Editing Chapter 5 Editing 5-3 5-1-3 Selecting the Editing Mode To select the editing mode Select assemble editing or insert editing. Depending on the editing mode, press the following button or buttons. • For assemble editing: ASSEMBLE button • For insert editing: the desired INSERT buttons (VIDEO, CH1 to CH4, CUE, TC) When you select[...]

5-1 A utomatic Editing Chapter 5 Editing 5-4 Chapter 5 Editing Setting split edit points In split editing, you can set the edit points for audio and video independently. Set the audio edit points with the AUDIO IN/OUT buttons, and the video edit points with the IN/OUT buttons. Note that split editing is only possible when the recording mode is inse[...]

Chapter 5 Editing Chapter 5 Editing 5-5 When the audio IN point is not set for insert editing of audio only As long as the audio OUT point is set, the VTR is ready for preview or editing. If the audio IN point has not been set, the current tape position is automatically used as the audio IN point. Using a VTR without a split editing function as the[...]

5-1 A utomatic Editing Chapter 5 Editing 5-6 Chapter 5 Editing 5-1-5 Modifying and Deleting Edit P oints If the edit points are not set correctly, for example if an OUT point is before a corresponding IN point, the DELETE button flashes, and it is not possible to carry out a preview or editing operation. In this case, either modify the erroneous ed[...]

Chapter 5 Editing Chapter 5 Editing 5-7 5-1-6 Cue-Up to Edit P oints and Prer oll To preroll to a position before an edit IN point or cue up to any edit point, use the following procedure. 1 Press the RECORDER button or PLAYER button to select the VTR on which you wish to operate. The button you have pressed lights. 2 •T o cue up to an edit point[...]

5-1 A utomatic Editing Chapter 5 Editing 5-8 Chapter 5 Editing 5-1-8 Carrying Out A utomatic Editing Monitor output During a preview, on a monitor connected to the recorder you can monitor the following video and audio. • From the preroll point to the IN point, you can monitor the playback from the recorder. • From the IN point to the OUT point[...]

Chapter 5 Editing Chapter 5 Editing 5-9 The following figure illustrates this. Using a single monitor for video and audio on both player and recorder For efficient editing if only one monitor is available, use the following method. 1 Connect the monitor to the recorder. 2 In the basic setup menu, set item 008 to AUTO. 3 Press the PLAYER button on t[...]

5-1 A utomatic Editing Chapter 5 Editing 5-10 Chapter 5 Editing After automatic editing, to adjust the edit points and reexecute the edit Hold down the DELETE button and press the ENTRY button to recall the edit points. After adjusting the edit points, press the AUTO EDIT button to carry out the edit again. For details of how to adjust edit points,[...]

Chapter 5 Editing Chapter 5 Editing 5-11 5-2 DMC Editing By controlling the player playback speed from the recorder you can achieve variable speed editing. 5-2-1 Overview of DMC Editing Conditions for DMC editing DMC editing can be used for insert or assemble editing, but not for audio split editing. Tape movement during DMC editing The following f[...]

5-2 DMC Editing 5-12 Chapter 5 Editing Chapter 5 Editing 5-2-2 Carrying Out DMC Editing Setting the edit points and player speed Use the following procedure. 1 Press the ASSEMBLE button or the desired INSERT button to select the editing mode. 2 Press the DMC EDIT button. This unit switches to the DMC editing mode, and the DMC EDIT button lights. 3 [...]

Chapter 5 Editing 5-13 Chapter 5 Editing This section describes the following automatic editing methods: •Q uick editing •C ontinuous editing • Standalone editing •M anual editing • Preread editing 5-3-1 Quic k Editing After selecting the edit mode, you can save on editing time by setting the edit points and executing the edit at the same[...]

5-3 Special A utomatic Editing Methods 5-14 Chapter 5 Editing Chapter 5 Editing 5-3-3 Standalone Editing This refers to editing using as the player an external device which cannot be controlled remotely through the REMOTE1-IN(9P) connector. For example, you can record a color bar signal from a signal generator in the joints between the scenes of an[...]

Chapter 5 Editing 5-15 Chapter 5 Editing Notes • In preread editing, if an input video signal is used as the reference signal for the output video signal, this forms a feedback loop. To prevent the occurrence of feedback, set the OUTREF in function menu page 4 to REF, and set item 309 in the extended setup menu to AUTO 1 so as to use an external [...]

Chapter 6 Shot Mark Function Chapter 6 Shot Mark Function 6-1 Chapter 6 Shot Mark Function 6-1 Overview This unit can record shot marks or use shot marks recorded in digital Betacam, MPEG IMX, or Betacam SX format. Shot marks are indications at desired points on a tape which enable faster cueing. Types of shot mark This unit supports the following [...]

6-1 Overview Chapter 6 Shot Mark Function 6-2 Chapter 6 Shot Mark Function Details of the shot mark operation menu The shot mark operation menu comprises four items, G01 to G04. The detailed contents appear in the following table. Changing the menu settings The basic procedure for accessing menu items and changing settings is the same as for the se[...]

Chapter 6 Shot Mark Function Chapter 6 Shot Mark Function 6-3 6-3 Shot Mark Operations This section describes the operations concerning reading and writing shot marks. Note that the following operations cannot be carried out by remote control. 6-3-1 Reading Shot Marks To read in shot marks With a cassette loaded, hold down the LIST button and press[...]

6-3 Shot Mark Operations Chapter 6 Shot Mark Function 6-4 Chapter 6 Shot Mark Function To write in crash recording or assemble editing 1 Hold the MARK button down for at least 2 seconds. 2 At the position you wish to write the mark, hold down the ENTRY button, and press the MARK button. A mark of the type selected in item G04 of the shot mark opera[...]

Chapter 6 Shot Mark Function Chapter 6 Shot Mark Function 6-5 Example of list display The following figure shows how the list is organized. Selecting a shot mark Turn the MULTI CONTROL knob to align the asterisk cursor with the desired shot mark. Entering virtual shot marks When the REC/ERASE indicator is off, hold down the ENTRY button and press t[...]

6-3 Shot Mark Operations Chapter 6 Shot Mark Function 6-6 Chapter 6 Shot Mark Function To delete an individual shot mark Use the following procedure. 1 With the shot mark list displayed, select the shot mark to be deleted using the MULTI CONTROL knob. 2 Hold the MARK button down. While you hold down the button, an “X” appears after the selected[...]

Chapter 6 Shot Mark Function Chapter 6 Shot Mark Function 6-7 Cueing up to shot marks adjacent to the current tape position (index function) 1 In item G01 of the shot mark operation menu (page 6-2) , select one of recording start mark, shot mark 1, shot mark 2, and post mark, or select all. 2 Holding down the MARK button, press the F FWD button or [...]

6-3 Shot Mark Operations Chapter 6 Shot Mark Function 6-8 Chapter 6 Shot Mark Function Z 3 21 6-3-6 Sor ting Shot Marks Based on shot data recorded on the tape, you can separate the shot marks by cassette, and sort them in time code sequence. To sort the shot marks Use the following procedure. 1 With the shot mark list displayed, press the F5 (SETI[...]

Chapter 7 Tele-File Chapter 7 Tele-File 7-1 Chapter 7 T ele-File 7-1 Overview of T ele-File Functions Tele-File is a non-contact data carrier system. Tele-File increases the efficiency of data management and operations such as recording, playback, and editing by enabling information to be exchanged between VTRs with data reading and writing functio[...]

7-1 Overview of T ele-File Functions Chapter 7 Tele-File 7-2 Chapter 7 Tele-File To open from the function menu Display page 5 of the function menu in the menu display section, and then press the F1 (TELE-F) button. The Tele-File menu opens. For details about the function menu, see Chapter 11 “Function Menu” (page 11-1). To open automatically W[...]

Chapter 7 Tele-File Chapter 7 Tele-File 7-3 7-3 T ele-File Menu 7-3-1 Clip Data Displa y Shown below are examples of the default menu displays in the menu display section and the monitor display. For more information about how to display menus on the monitor, see the section “To display menus on the monitor” (page 12-2). Tele-File menu indicato[...]

7-3 T ele-File Menu 7-4 Chapter 7 Tele-File Chapter 7 Tele-File Setting display area Displays the setting of the currently selected data type, and a cursor (“*” or “>”). The meaning of the cursor symbols is as follows: *: Indicates that the mode is clip data display mode or attribute data display/modify mode, and that data is selected. &[...]

Chapter 7 Tele-File 7-5 Chapter 7 Tele-File Title The title (maximum 14 characters) set in attribute data display/modify mode. Selected clip number A 4-digit number representing the number of the selected clip (with the “*” cursor). Remaining memory percentage The percentage of remaining memory (user area) available for use. If there is not suf[...]

7-3 T ele-File Menu 7-6 Chapter 7 Tele-File Chapter 7 Tele-File Moving the cursor directly Regardless of the cursor’s current position, pressing one of the following buttons moves the cursor directly to the specified position in the same clip and displays the data. IN (video IN point) button: IN point data OUT (video OUT point) button: OUT point [...]

Chapter 7 Tele-File 7-7 Chapter 7 Tele-File 7-3-3 Modifying Clip Data To modify clip data, put the unit into clip data display mode and then press the F2 (SELECT) button to put it into clip data modification mode (the cursor changes to “>”). The function assignments for menu items in clip data modification mode are as follows. Clip data modi[...]

7-3 T ele-File Menu 7-8 Chapter 7 Tele-File Chapter 7 Tele-File To add and delete clips To add clips 1 Rotate the MULTI CONTROL knob to move the “*” cursor to the position where you want to insert the clip. 2 Press the F2 (SELECT) button. The unit enters clip data modification mode. 3 Press the F5 (INS LN) button. A confirmation message “INSE[...]

Chapter 7 Tele-File 7-9 Chapter 7 Tele-File To set the set or modified data as other time data Press the F6 (SET TO) button and select the time data (cue point, IN point, or OUT point), and then press the F5 (SET) or F6 (SET NL) button. The position where the data is set differs as follows, depending on the button pressed. • F5 (SET): The data is[...]

7-3 T ele-File Menu 7-10 Chapter 7 Tele-File Chapter 7 Tele-File To make comment settings Proceed as follows to make comment settings. 1 Select a clip. 2 Select comment. 3 Press the F2 (SELECT) button. The unit enters clip data modification mode. 4 Press the F2 (MODIFY) button. The data entry area begins to flash, and the data can be set. 5 Enter a[...]

Chapter 7 Tele-File 7-11 Chapter 7 Tele-File 7-3-5 Displa ying and Modifying Attrib ute Data You can display and modify attribute data. The example below shows attribute data displayed on the monitor. Video final recording date The most recent date (year/month/day) on which video was recorded on the tape. Title The title (name assigned to Tele-File[...]

7-3 T ele-File Menu 7-12 Chapter 7 Tele-File Chapter 7 Tele-File To modify attribute data You can modify the title, ID, administrator data, and write inhibit setting attributes. However, the attributes cannot be modified when the write inhibit setting is ON. Proceed as follows after setting the write inhibit setting to OFF. 1 Rotate the MULTI CONTR[...]

Chapter 8 UMID Functions Chapter 8 UMID Functions 8-1 Chapter 8 UMID Functions 8-1 Overview of UMID Functions The UMID (Unique Material Identifier) is a type of meta-data in video and audio materials. It has been internationally standardized in SMPTE Standard 330M. This unit supports recording and generation of UMIDs. The UMID is made up of a secti[...]

8-1 Overview of UMID Functions Chapter 8 UMID Functions 8-2 Chapter 8 UMID Functions 8-2 Recor ding UMIDs UMIDs can be recorded when recording video signals with this unit. You can select whether to inherit (copy) the UMID contained in input signals, or automatically or forcibly generate a new UMID. Selecting the type of UMID to record Select wheth[...]

Chapter 8 UMID Functions Chapter 8 UMID Functions 8-3 ITEM-029 ORGANIZATION - YYYY COUNTRY - XXXX *USER - ABCD STORED OWNERSHIP 2 Press the F3 (PREV) and F4 (NEXT) buttons to select the item you want to set (COUNTRY, ORGANIZATION, or USER). The selected item (example: USER) is shown in F2. SET EXIT ITEM USER PREV NEXT SET UP 029:USER - ABCD HOME F1[...]

8-1 Overview of UMID Functions Chapter 8 UMID Functions 8-4 Chapter 8 UMID Functions 8-3 UMID Output and Displa y This section explains how to output and display UMIDs. 8-3-1 UMID Output Settings You can choose to output UMIDs or not, and select either Basic UMID or Extended UMID when you choose to output UMIDs. Make these settings using setup menu[...]

Chapter 8 UMID Functions Chapter 8 UMID Functions 8-5 Note The function for converting unit count to UTC works only when the unit rate is 2 (24 frames), 3 (24/1.001 frames), 4 (25 frames), 6 (30 frames), or 7 (30/1.001 frames). For other unit rates, the unit rate number and unit rate are displayed in hexadecimal. 5 Altitude XXXXXXXXm: Altitude data[...]

Chapter 9 Essence Marks Chapter 9 Essence Marks 9-1 Chapter 9 Essence Marks 9-1 Overview of Essence Mark Functions An essence mark uses a term value dictionary item as defined in the SMPTE RP210A Metadata Dictionary to express and transfer points such as recording start points and edit point candidates in up to 32 bytes of data. The basic format of[...]

9-1 Übersic ht über die Essenzmarken-Funktionen Chapter 9 Essence Marks 9-2 Chapter 9 Essence Marks 9-2 Essence Mark Recor ding and Output 9-2-1 Essence Mark Recor ding Essence marks contained in SDI input signals and essence marks generated by this unit can be recorded to tape together with video signals. All essence mark data generated by this [...]

Chapter 10 Auto Event Detector Chapter 10 Auto Event Detector 10-1 Chapter 10 A uto Event Detector 10-1 Overview of A uto Event Detector Functions The Auto Event Detector (AED) detects locations where video signals show large changes (cuts), and locations where the video suddenly becomes brighter for a short period (flash). Detected events can be c[...]

Chapter 11 Function Menu Chapter 11 Function Menu 11-1 Chapter 11 Function Menu 11-1 Overview of the Function Men u The function menu allows you to make frequently made settings, such as selection of input video signals and time code settings. 11-1-1 Function Menu Configuration The function menu consists of six pages by factory default: the HOME pa[...]

11-1 Overview of the Function Men u Chapter 11 Function Menu 11-2 Chapter 11 Function Menu 11-1-2 Using the Function Menu To change a menu item setting To change a menu item setting, press the corresponding function button (F1 to F6) to display the desired setting in the lower part of the menu display. Each press of the button displays the next set[...]

Chapter 11 Function Menu Chapter 11 Function Menu 11-3 11-2 Function Men u Item List The function menu has the following items. HOME page a) The selection of LTC or VITC depends on the setting of F6 (TCR) in function menu page 1. Item F1 (VID.IN) F2 (PB/EE) F3 (CONFI) F4 (CTL/TC) F5 (MENU) F6 (TCGSET) Setting Selects the input video signal. COMPST:[...]

11-2 Function Menu Item List Chapter 11 Function Menu 11-4 Chapter 11 Function Menu Page 1 Item F1 (TCG) F2 (TCG) F3 (RUN) F4 (DF) F5 (VITC) F6 (TCR) Setting Selects the time code to use. INT: Time code generated by the internal time code generator EXT: One of the following time codes • When F6 (TCR) is set to LTC or AUTO, the external time code [...]

Chapter 11 Function Menu Chapter 11 Function Menu 11-5 Page 2 Item F1 (V.PROC) F2 (VIDEO) F3 (CHROMA) F4 (HUE) (525- line mode)/ (C PHAS) (625- line mode) F5 (SETUP) (525-line mode)/ (BLACK) (625- line mode) F6 (YC DLY) (DVW-M2000/ M2000P only) Setting Selects the control method for the internal digital video processor. LOCAL: Change the settings o[...]

11-2 Function Menu Item List Chapter 11 Function Menu 11-6 Chapter 11 Function Menu Page 3 Item F1 (SYNC) F2 (SC) F3 (VIN LV) F4 (EMPHSS) F5 (T INFO) Setting Sets the output signal sync phase. Setting method With the displayed setting flashing, you can rotate the MULTI CONTROL knob to adjust the output signal sync phase across the range ±15 µs re[...]

Chapter 11 Function Menu Chapter 11 Function Menu 11-7 Page 4 Item F1 (CAPSTN) F2 (OUTREF) F3 (DOLBY) (DVW-M2000/ M2000P only) F4 (CHARA) Setting Selects the number of fields for capstan lock in playback and editing. For DVW-M2000/2000 2F: The capstan servo locks in units of 2 fields. • For tape output, color framing may not match the reference s[...]

11-2 Function Menu Item List Chapter 11 Function Menu 11-8 Chapter 11 Function Menu Page 5 Item F1 (TELE-F) F2 (UMID) F5 (SUPUTL) Setting Displays the Tele-File menu. For details of the Tele-File menu, see Section 7-3 “Tele-File Menu” (page 7-3). Displays UMID information during recording/playback. For details of UMID, see Chapter 8. Displays t[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-1 Chapter 12 Setup Menus 12-1 Setup Menu Configuration This unit has the following setup menus. •B asic setup menu • Extended setup menu To access the extended setup menu, a setting on the internal SS-89 board is required. For details, refer to the Installation Manual. In this manual, both the ba[...]

12-2 Setup Menu Operations Chapter 12 Setup Menus 12-2 Chapter 12 Setup Menus 12-2 Setup Men u Operations To display setup menus With the function menu HOME page showing in the menu display, press the F5 (MENU) button. The currently selected setup menu item is displayed in the menu display, with the menu item number flashing. For basic operations i[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-3 To display a desired sub-item For a menu item having sub-items, you can select a desired sub-item as follows. 1 With a desired menu item selected, press the F2 (SELECT) button. The currently selected sub-item name flashes. 2 Turn the MULTI CONTROL knob to select a desired sub-item. Changing menu it[...]

12-2 Setup Menu Operations Chapter 12 Setup Menus 12-4 Chapter 12 Setup Menus Resetting the menu settings to their factory default values (menu item B20) To reset the current active menu settings to their factory default values, proceed as follows. 1 Perform steps 1 to 3 of the procedure described in the section “To change the settings of menu it[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-5 12-3 Items in the Basic Setup Men u a) When setting items 002 and 003, watch the monitor screen, and adjust to the required state. Item number 001 002 a) 003 a), b) 004 005 006 007 008 Item name PREROLL TIME CHARACTER H- POSITION CHARACTER V- POSITION SYNCHRONIZE DISPLAY INFORMATION SELECT LOCAL FU[...]

12-3 Items in the Basic Setup Menu Chapter 12 Setup Menus 12-6 Chapter 12 Setup Menus a) When setting items 009 and 011, watch the monitor screen, and adjust to the required state. b) The channel condition indication appears under the timer or status line (under the video playback level indication during playback of an analog tape), in the format ?[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-7 Item number 023 029 B01 B02 B03 B11 B12 B13 B20 Item name LOCAL KEY MAP 1 STOP 2 PLAY 3 REC/EDIT 4 STANDBY 5 EJECT 6 JOG 7 SHUTTLE 8 VAR 9 FF/REW 10 PREROLL 11 AUTO/PRE/REVIEW 12 F-KEY 13 AUDIO/MONITOR 14 EDIT PRESET 15 OTHERS STORED OWNERSHIP RECALL BANK 1 RECALL BANK 2 RECALL BANK 3 SAVE BANK 1 S[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-8 Chapter 12 Setup Menus 12-4 Items in the Extended Setup Men u The extended setup menu contains the following items. In the “Settings” column of the table, the factory default settings are indicated by an enclosing box. Menu items in the range 100 to 199, relating to the control p[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-9 Menu items in the range 100 to 199, relating to the control panels (Continued) Item number 107 108 109 111 115 116 117 Item name REC INHIBIT LAMP FLASHING AUTO EE SELECT FORCED EE WHEN TAPE UNTHREAD TSO PLAY PHASE LOCK IN VARIABLE X3 (DVW- M2000/M2000P only) JOG DIAL RESPONSE CONTROL PANEL SELECTIO[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-10 Chapter 12 Setup Menus Menu items in the range 100 to 199, relating to the control panels (Continued) Item number 118 119 120 121 125 130 Item name KEY INHIBIT SWITCH EFFECTIVE AREA Sub-item 1 REMOTE SELECT 2 AUDIO/F-KEY 3 MODE CONTROL VARIABLE SPEED LIMIT IN KEY PANEL CONTROL CTL L[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-11 Menu items in the range 100 to 199, relating to the control panels (Continued) Item number 133 134 135 136 Item name TELE-FILE CONTROL MODE TELE-FILE MENU AUTO POPUP TELE-FILE THREAD COUNTER CLEAR MODE TELE-FILE IN OUT INPUT CONTINUE Settings Selects the device used for data modification operation[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-12 Chapter 12 Setup Menus Menu items in the range 300 to 399, relating to editing operations Item number 301 302 304 305 306 307 Item name VAR SPEED RANGE FOR SYNCHRONIZATION CAPSTAN RE-LOCKING DIRECTION EDIT FIELD SELECT SYNC GRADE DMC INITIAL SPEED AUTO-DELETION FOR INCONSISTENT DATA[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-13 Menu items in the range 300 to 399, relating to editing operations (Continued) Item number 308 309 310 311 312 313 314 315 Item name SELECTION OF STD/ NON-STD FOR COMPOSITE VIDEO IN SERVO/AV REFERENCE SEL REC INHIBIT ANALOG AUDIO EDIT PRESET REPLACE FOR CH1 ANALOG AUDIO EDIT PRESET REPLACE FOR CH2[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-14 Chapter 12 Setup Menus Menu items in the range 300 to 399, relating to editing operations (Continued) Item number 316 317 318 319 320 326 334 336 Item name CONFIDENCE PB MODE AUDIO EDIT MODE EDIT RETRY PREREAD SELECT DIGITAL AUDIO PB PROCESS ON EDIT POINT AUTOMATIC IN ENTRY AFTER AU[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-15 Menu items in the range 400 to 499, relating to preroll Item number 401 402 403 405 Item name FUNCTION MODE AFTER CUEUP TIME REFERENCE FOR PREROLL AUTOMATIC PREROLL REFERENCE ENTRY CUEUP BY CTL Settings Select the state that the unit goes into after a cuing-up operation. STOP : Stop (the “stop m[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-16 Chapter 12 Setup Menus Menu items in the range 600 to 699, relating to the time code generator Item number 601 602 603 604 605 Item name VITC POSITION SEL-1 VITC POSITION SEL-2 ID CODE PRESET ID CODE SW TCG REGEN MODE Settings In 525-line mode Select a line to insert the VITC in. 12[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-17 Menu items in the range 600 to 699, relating to the time code generator (Continued) Item number 606 607 608 609 Item name TC OUTPUT SIGNAL IN REGEN MODE U-BIT BINARY GROUP FLAG PHASE CORRECTION TCG CF FLAG Settings Select the signal output from the TIME CODE OUT connector during normal ( × 1) spe[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-18 Chapter 12 Setup Menus Menu items in the range 600 to 699, relating to the time code generator (Continued) Item number 610 651 652 654 655 Item name REGEN CONTROL MODE UMID OUTPUT UMID SD VANC LINE UMID GENERATE METHOD UMID RECORDING Settings In editing performed using the control p[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-19 Menu items in the range 600 to 699, relating to the time code generator (Continued) Item number 656 657 658 659 660 Item name MATERIAL NO. ESSENCE MARK TAPE OUTPUT SHOT MARK ESSENCE MARK CONVERT AED ESSENCE MARK CONVERT ESSENCE MARK SD VANC LINE Settings Select whether to inherit the UMID in the i[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-20 Chapter 12 Setup Menus Menu items in the range 600 to 699, relating to the time code generator (Continued) Item number 661 662 663 664 Item name ESSENCE MARK INPUT RECORD ESSENCE MARK SELF RECORD Sub items 1 crash rec 2 assemble 3 insert UMID OUT DUP DIGITAL BETACAM ESSENCE MARK OUT[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-21 Menu items in the range 700 to 799, relating to video control Item number 701 703 DVW-M2000/ 2000 DVW- M2000P/ 2000P 704 DVW-M2000/ 2000 DVW- M2000P/ 2000P 705 Item name SELECTION OF VIDEO/ SYNC DELAY BLANK LINE SELECT 0 ALL LINE 12 ... LINE 12 ... LINE 19 19 20 LINE 20 9 ... 22 LINE 9 ... LINE 22[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-22 Chapter 12 Setup Menus Menu items in the range 700 to 799, relating to video control (Continued) Item number 707 709 710 Item name FORCED VERTICAL INTERPOLATION OFF CAV LEVEL FORMAT (DVW-M2000/M2000P only) Sub-Item 0 INPUT CAV LEVEL 1 OUTPUT CAV LEVEL INTERNAL VIDEO SIGNAL GENERATOR[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-23 Menu items in the range 700 to 799, relating to video control (Continued) Item number 712 713 Item name VIDEO PROCESS ON CAP LOCK 2FIELD VIDEO SETUP REFERENCE LEVEL (DVW-M2000 only) 0 MASTER LEVEL 1 INPUT LEVEL 2 INPUT VBLK CONT 3 BETACAM PB LEVEL (DVW-M2000/M2000P) 4 OUTPUT LEVEL (Continued) Sett[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-24 Chapter 12 Setup Menus Menu items in the range 700 to 799, relating to video control (Continued) (Items 715 to 721: Settings for controlling the video processing system according to the menu settings) Item number 715 716 717 718 719 720 721 Item name VIDEO GAIN CONTROL CHROMA GAIN C[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-25 Menu items in the range 700 to 799, relating to video control (Continued) Item number 726 727 728 733 Item name H BLANKING WIDTH VIDEO EDIT PREVIEW SWITCHER OUTPUT SCH PHASE C.PHASE TYPE Settings Select the horizontal blanking width of the video output signal. NAROW : Digital blanking (narrow) WID[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-26 Chapter 12 Setup Menus Menu items in the range 800 to 899, relating to audio control a) Cross-fade time is 24 ms. b) Actual value is 49 ms. c) Actual value is 114 ms. Item number 801 802 803 805 806 Item name DIGITAL JOG SOUND DIGITAL AUDIO MUTE IN SHUTTLE MODE DIGITAL AUDIO FADE TI[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-27 Menu items in the range 800 to 899, relating to audio control (Continued) Item number 807 808 809 810 815 Item name AUDIO OUTPUT PHASE INTERNAL AUDIO SIGNAL GENERATOR AUDIO LEVEL METER DIMMER CONTROL AUDIO EDIT PREVIEW SWITCHER AUDIO SAMPLING RATE CONVERTER Settings Select the output timing of dig[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-28 Chapter 12 Setup Menus Menu items in the range 800 to 899, relating to audio control (Continued) Item number 823 824 825 Item name NAU FLG PB Sub-item 1 CH1/CH2 2 CH3/CH4 3 CCH5/CH6 (DVW-M2000/ M2000P only) Valid only for an MPEG IMX format 8-channel recording tape 4 CH7/CH8 (DVW-M2[...]

Chapter 12 Setup Menus Chapter 12 Setup Menus 12-29 Menu items in the range 800 to 899, relating to audio control (Continued) Item number 826 827 828 Item name AUDIO PB VOLUME SELECT (DVW-M2000/M2000P only) Sub-item 0 ALL CH 1 CH1 2 CH2 3 CH3 4 CH4 5 CH5 6 CH6 7 CH7 8 CH8 AES/EBU AUDIO OUTPUT SELECT Sub-item 1 CH1/CH2 2 CH3/CH4 SDI AUDIO OUTPUT SEL[...]

12-4 Items in the Extended Setup Menu Chapter 12 Setup Menus 12-30 Chapter 12 Setup Menus Menu items in the range 900 to 999, relating to digital processing Item number 901 903 904 905 906 920 Item name VIDEO OUTPUT DATA FREEZE MODE FREEZE CONTROL FROM KEY PANEL AUTO FREEZE CONTROL STOP FREEZE CONTROL SD-SDI H-ANC Sub-item 1 AUDIO 5CH-8CH (DVW-M200[...]

Chapter 13 Setup Utility Menu Functions Chapter 13 Setup Utility Menu Functions 13-1 Chapter 13 Setup Utility Menu Functions 13-1 Overview of Setup Utility Men u Functions You can use the setup utility menu to download files saved in memory sticks, to upload files to memory sticks, and to format memory sticks from MS-DOS. Call up the setup utility [...]

13-1 Overview of Setup Utility Menu Functions Chapter 13 Setup Utility Menu Functions 13-2 Chapter 13 Setup Utility Menu Functions 5 Press the F5 (SET) button. The selected file is downloaded. Note Do not do any of the following during the download. Doing so can corrupt the ROM software of this unit, making the unit unable to download normally. •[...]

Chapter 13 Setup Utility Menu Functions Chapter 13 Setup Utility Menu Functions 13-3 3 Press the F5 (SET) button. Formatting is executed. If you are using a new memory stick, or if an error occurs during execution of F3: FORMAT STICK, use the sub mode to format the memory stick. Note All data in the memory stick is erased when you execute F3: FORMA[...]

Chapter 14 Maintenance and Inspection Chapter 14 Maintenance and Inspection 14-1 Chapter 14 Maintenance and Inspection 14-1 Remo ving a Cassette When T ape Slack Occur s If tape slack occurs in the unit, it is necessary to remove the upper lid and sound baffle. This job should always be entrusted to a technician who has undergone service training. [...]

14-5 Regular Chec ks Chapter 14 Maintenance and Inspection 14-2 Chapter 14 Maintenance and Inspection 14-3 Err or Messages This unit is equipped with a self-diagnosis function, and if a problem is detected, displays an error message in the time data display and on the monitor. If an error message appears, contact your Sony service representative. I[...]

Chapter 14 Maintenance and Inspection Chapter 14 Maintenance and Inspection 14-3 Error Message List Code – 01 02 03 04 05 06 07 08 09 0A 10 11 12 13 14 20 21 22 23 92 93 95 96 97 98 99 Message NO COMMUNICATION REEL TROUBLE REEL TROUBLE REEL TROUBLE REEL TROUBLE REEL TROUBLE TAPE TENSION CAPSTAN TROUBLE DRUM TROUBLE TH/UNTH MOTOR THREADING HUMID T[...]

14-5 Regular Chec ks Chapter 14 Maintenance and Inspection 14-4 Chapter 14 Maintenance and Inspection 14-4 Moisture Condensation When the unit is suddenly moved from a cold to a warm location, or used in a very humid place, moisture from the air can condense on the head-drum. This is called moisture condensation. If the tape is run in this state, i[...]

Chapter 14 Maintenance and Inspection Chapter 14 Maintenance and Inspection 14-5 14-5 Regular Chec ks 14-5-1 Digital Hours Meter The hours meter can display seven items of information, in corresponding display modes, about the operational history of the unit. Use it as a guide in scheduling periodic maintenance. Display modes of the hours meter H01[...]

14-5 Regular Chec ks Chapter 14 Maintenance and Inspection 14-6 Chapter 14 Maintenance and Inspection Component Digital hours meter indication (menu number in parenthesis) Guideline replacement intervals R: Replace C: Check, and replace if necessary 1000 hrs 2000 hrs 3000 hrs 4000 hrs 5000 hrs 6000 hrs R (Replace at interval of 4000 hours.) 14-5-2 [...]

Appendix Appendix A-1 Appendix Specifications General Recording format Digital Betacam Power requirements 100 to 240 VAC, 50/60 Hz Power consumption 2.2 A (220 W) (DVW-M2000/ M2000P) 2 A (200 W) (DVW-2000/2000P) Peak inrush current (1) Power ON, current probe method: 54 A (240 V), 20 A (100 V) (2) Hot switching inrush current, measured in accordanc[...]

Specifications Appendix A-2 Appendix Recommended tapes Digital Betacam cassettes (S, L): BCT-D6/D12/D22/D32/D40 BCT-D34L/D64L/D94L/D124L MPEG IMX cassettes (S, L) (for playback only on DVW-M2000/ M2000P) Betacam SX cassettes (S, L) (for playback only on DVW-M2000/ M2000P) Betacam SP cassettes (S, L) (for playback only on DVW-M2000/ M2000P) Betacam [...]

Appendix Appendix A-3 MPEG IMX playback (DVW-M2000/M2000P) Video Digital Audio Betacam SX playback (DVW-M2000/M2000P) Video Audio Analog Betacam playback (DVW-M2000) Video Bandwidth S/N ratio K factor Y R–Y/B–Y DVW-M2000: 0 to 5.75 MHz +0.5 dB/–2 dB DVW-M2000P: 0 to 2.75 MHz +0.5 dB/–2 dB 0 to 2.75 MHz +0.5 dB/–2dB 56 dB or more 1% or les[...]

Specifications Appendix A-4 Appendix Analog Betacam playback (DVW-M2000P) Video Audio a) Peak level: +8 dB above reference level b) Reference level: +4 dBm Audio a) Reference level: +4 dBm LNG AFM Frequency response (at 10 dB below reference level a) ) S/N ratio (at 3% distortion level) Distortion (THD at 1 kHz reference level a) ) Wow and flutter [...]

Appendix Appendix A-5 Processor adjustment range Video level ±3 dB/ – ∞ to +3 dB selectable Chroma level ±3 dB/ – ∞ to +3 dB selectable Setup level (DVW-M2000/2000) ±30 IRE Black level (DVW-M2000P/2000P) ±210 mV Y/C delay ±100 ns (in analog Betacam playback) Chroma phase ±30° System phase Sync: ±15 µs SC: ±200 ns Input connectors [...]

Specifications Appendix A-6 Appendix Remote connectors CONTROL PANEL 10-pin (2), female Front/rear selectable REMOTE 1-IN (9P) D-sub 9-pin, female REMOTE 1-OUT (9P) D-sub 9-pin, female RS-232C D-sub 9-pin, male VIDEO CONTROL D-sub 15-pin, male (for optional BVR-50/50P) REMOTE 2 PARALLEL I/O (50P) 50-pin, female Memory stick slot Memory stick (8 to [...]

Index Index I-1 Index Index (Continued) A AC IN connector 2-17 ALARM indicator 2-11 Analog audio input/output section 2-15 device connection 3-2 video input/output section 2-16 ASSEMBLE button 2-11 Audio monitor signal output section 2-18 selection function selector buttons 2-4 setting display section 2-5 signal selection buttons 2-5 AUDIO IN/OUT b[...]

Index Index I-2 Index MENU (function menu) 11-3 Menu control buttons 2-6 display 2-8 operation 2-6, 6-2, 12-2 MIXING button 2-4 Moisture condensation 14-4 MONITOR OUTPUT connectors 2-18 MPEG IMX 1-1 cassette 3-10 compatibility 1-2 N Non-drop frame mark 3-9 mode 11-4 O Operation mode 3-9 OPTION connector 2-18 OUTREF (function menu) 11-7 P PANEL SELE[...]

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenan[...]

 2004 DVW-M2000/M2000P DVW-2000/2000P (SY, ) 3-826-015- 03 (1) Son y Cor poration B & P Company[...]