Sony DXC-D35 manuel d'utilisation

COLOR VIDEO CAMERA DXC-D35 DXC-D35P DXC-D35WS DXC-D35WSP SERVICE MANUAL V olume 1 1st Edition WS[...]

DXC-D35/D35WS (UC) DXC-D35P/D35WSP (CE) V1 ! W ARNING This manual is intended f or qualified ser vice personnel only . T o reduce the r isk of electric shoc k, fire or injur y , do not perf orm an y ser vicing other than that contained in the oper ating instructions unless you are qualified to do so. Refer all servicing to qualified service personn[...]

DXC-D35/D35WS (UC) DXC-D35P/D35WSP (CE) V1 1 (P) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manuf acturer . Dispose of used batteries according to the manuf acturer’ s instr uctions . V orsicht! Explosionsgefahr bei unsachgemäßem A ustausch der Batterie. Ersat[...]

DXC-D35/D35WS (UC) DXC-D35P/D35WSP (CE) V1 X-RAY RADIATION WARNING Be sure that parts replacement in the high voltage block and adjustments made to the high voltage circuits are carried out precisely in accordance with the procedures given in this manual. For the customers in the U.S.A. and Canada RECYCLING NICKEL-CADMIUM BATTERIES Nickel Cadmium b[...]

DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 1 Table of Contents Manual Structure Purpose of this manual .............................................................................................. 3 Related manuals ......................................................................................................... 3 1. Operating Instructions 2.[...]

DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2 3. Electrical Alignment 3-1. Preparation .................................................................................................. 3-1 3-1-1. Equipment Required ................................................................... 3-1 3-1-2. Connection ...............................................[...]

3 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Purpose of this manual This is the Service Manual Volume 1 of the color video camera DXC-D35/D35P and DXC-D35WS/D35WSP. Contains the operation manual related to the operations of this equipment, the replacement of the parts and adjustments. Related manuals Besides this Service Manual Volume 1, the followin[...]

[...]

1-1 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Section 1 Operating Instructions This section is extracted from operation manual.  2000 by Sony Corporation Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. 3-203-895- 11 (1) Color Video Camera WS DXC-D35K/D35PK DXC-D35L/D35PL DXC[...]

1-2 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2 WARNING Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. Note Keep the lithium battery out of the reach of children. Should the battery be swallowed, consult a doctor immediately. ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må[...]

1-3 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 4 Table of Contents T able of Contents Chapter 2 Fitting and Connection Chapter 1 Overview T able of Contents Product Configurations .................................................... 7 Features ............................................................................. 9 Features on the DXC-D35/D35P[...]

1-4 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 6 Table of Contents T able of Contents Appendix Chapter 5 Adjustments and Settings White Balance Adjustment ............................................. 79 Saving an Appropriate White Balance V alue in Memory .................................................................... 79 Using the Preset White [...]

1-5 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 1 Overview 8 Chapter 1 Overview VCT-U14 Tripod Adaptor Microphone DXF-801/801CE Viewfinder DXC-D35H/D35PH Test chart for flange focal length adjustment DXC-D35/D35P/D35WS a) / D35WSP a) Camera Head b) VCL-918BY Zoom Lens DXC-D35K/D35PK DXC-D35L/D35PL RM-LG1 Remote Control Unit a) DXC-D35WSL/D35WS[...]

1-6 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 1 Overview 10 Chapter 1 Overview ClipLink™ Function (when using DSR- 1/1P) The ClipLink function can be used at every step from acquisition to editing. Information necessary for editing is recorded when shooting to ensure fast and efficient editing operations. When you set a recording start (Re[...]

1-7 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 1 Overview 12 Chapter 1 Overview Features on the DXC-D35WSL/ D35WSPL Features only on the DXC-D35WSL/S35WSPL is described in this section. See “Features on the DXC- D35/D35P/D35WSL/D35WSPL” (page 9) for common features on a 4:3 standard-screen type digital video camera and 16:9 wide-screen ty[...]

1-8 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 1 Overview 14 Chapter 1 Overview 1 EZ (“easy”) MODE button and indicator Depress this button (EZ mode on) when you want to be able to shoot immediately, with automatic adjustment of the camera settings to standard values. (See page 68.) When this function is used, the iris and the white balan[...]

1-9 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 1 Overview 16 Chapter 1 Overview wa UP/ON button Use this button to open displays and to make “ON” settings. When using the advanced menus, use this button to change menu pages or to switch to the ordinary screen display. ws DOWN/OFF button Use this button to close displays and to make “OFF[...]

1-10 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 1 Overview 18 Chapter 1 Overview 7 REMOTE connector 1 (mini-jack) Connect the RM-LG1 Remote Control Unit to enable remote operation of the ClipLink function. 8 MONITOR OUT connector (BNC) Outputs both the camera video and the character information as displayed on the viewfinder screen. You can c[...]

1-11 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 1 Overview 20 Chapter 1 Overview Location and Function of P ar ts 1 Iris ring For manual iris control, set the IRIS selector qd to the “M” position, and turn this ring. 2 Zoom ring For direct manual zoom control, set the ZOOM selector 7 to the “MANU.” position, and turn this ring. 3 Focu[...]

1-12 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 1 Overview 22 Chapter 1 Overview Location and Function of P ar ts 6 REC/TALLY (recording/tally) indicators (red) • This flashes from the time when you press the VTR button ( 0 on page 17 and qa on page 20) on the lens or camcorder until recording starts, then stays on continuously during recor[...]

1-13 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 24 Chapter 2 Fitting and Connections Press down and pull out toward you. Rear of the camera head Battery cover 1 Pull the upper part of the battery cover (on the rear of the camera head) forward and turn the cover clockwise. For detaching the VTR or camera adaptor, see [...]

1-14 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 26 Chapter 2 Fitting and Connections 4 Slide the DSR-1/1P and the camera head together in the groove as far as possible. 5 Tighten the two screws in the grip connector and the two screws in the shoulder pad section. Screws 6 Attach the shoulder pad. To remove the VTR Re[...]

1-15 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 28 Chapter 2 Fitting and Connections 5 Perform the first three steps in “Fitting a VTR”. 6 Screw the connection plate (supplied with the grip for the DVCAM camcorder) which straddles the connection between the camera head and the DSR-1/1P. Also, tighten the two scre[...]

1-16 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 30 Chapter 2 Fitting and Connections Fitting the Lens In the case of the DXC-D35K/D35PK model, the lens is already fitted. In other cases, use the following procedure to fit the lens. 1 Remove the retaining rubber which prevents the lens mount from coming loose, then ra[...]

1-17 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 32 Chapter 2 Fitting and Connections Using the Viewfinder Removing the Viewfinder Remove any microphone from the viewfinder before beginning. 1 Pull the viewfinder connector out of the VF connector on the front of the camera head. 2 Loosen the viewfinder left-to- right [...]

1-18 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 34 Chapter 2 Fitting and Connections Fitting optional microphones (operable with a 48 V supply) other than the ECM-670 Use the same fitting procedure as for the ECM-670, but note the following differences with respect to the microphone adaptor. ECM-672: no microphone ad[...]

1-19 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 36 Chapter 2 Fitting and Connections Connections Connecting a P ortable VTR Using the optional CA-537/537P or CA-327/327P Camera Adaptor and a camera cable, you can connect a portable VTR. Set the VTR selector switch on the camera adaptor according to the VTR connected.[...]

1-20 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 38 Chapter 2 Fitting and Connections INTERCOM VIDEO IN PGM OUT TALLY/INTERCOM PGM OUT VBS OUT RETURN VIDEO IN GEN LOCK IN TALLY/INTERCOM VIDEO IN VIDEO IN GEN LOCK OUT RETURN VIDEO OUT VBS OUT CAMERA CAMERA TALLY/INTERCOM VBS OUT GEN LOCK IN RETURN VIDEO IN 1 4 2 2 3 3 [...]

1-21 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 2 Fitting and Connections 40 Chapter 2 Fitting and Connections P ower Supply This unit operates on either a battery pack or an AC supply (using the optional CMA-8A/8ACE AC Adaptor). For details of the power supplies which can be used, refer to the documentation supplied with the VTR connected to[...]

1-22 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 3 Shooting 43 Chapter 3 Shooting Basic Procedure f or Shooting FILTER control Focusing ring RET button VTR button ZEBRA switch POWER switch 1 Attach the VTR or camera adaptor to the camera head, then turn each device’s power on. 2 Set the FILTER control appropriately for the lighting condition[...]

1-23 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 44 Chapter 3 Shooting Chapter 3 Shooting 1) Hunting: This occurs if the automatic iris function is not able to reach a stable state, and as a result the image brightness keeps changing, alternately lighter and darker. 2) Depth of field: This is the range over which the subject is sharply in focus. .....[...]

1-24 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 46 Chapter 3 Shooting Chapter 3 Shooting Shooting with the DSR-1/1P The DXC-D35/D35P/D35WS/D35WSP docks with the DSR-1/1P to configure a DVCAM Camcorder. The following describes how to shoot using a DVCAM camcorder. Using the ClipLink Function The ClipLink function can be used at all stages from shootin[...]

1-25 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 48 Chapter 3 Shooting Chapter 3 Shooting Setting cue points as you shoot You can make edit search operations easier by specifying cue points to highlight scenes. 1 Perform steps 1 and 2 in “Using the ClipLink Function” (page 46) . 2 Access basic menu page 6 and perform the following operations. 1) S[...]

1-26 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chapter 4 Viewfinder Screen Indications and Menus 51 Chapter 4 Vie wfinder Screen Indications and Menus Viewfinder Screen Indications There are four types of indication screen which appear in the viewfinder, as follows. • Normal indications These show the operating state of the camera and connected VT[...]

1-27 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 52 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Displaying the advanced menu and switching to the normal indications Use the following procedure to display the advanced menu. 1 Move the POWER switch to the ON position while holding down the UP/ON bu[...]

1-28 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 54 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Viewfinder Normal Indications During normal operation, the following items can be indicated in the viewfinder. The significance of each of the indications shown in the figure is as follows. 1 VTR opera[...]

1-29 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 56 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Only when connecting the DSR-1/1P qf White balance indication The following indications appear. qg SKIN DTL indication This appears when the skin detail function is activated (The SKIN DTL switch is se[...]

1-30 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 58 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Viewfinder Basic Men u To display the basic menu pages, press the MENU/ STATUS switch downward while the normal indications are being shown in the viewfinder. The basic menu configuration can include u[...]

1-31 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 60 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Setting the recording time in seconds Move the cursor to DUR TIME, then press the UP/ON button or DOWN/OFF button. A value of seconds is displayed under “SS”. Basic menu page 6 The following displa[...]

1-32 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 62 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus 4 Press the UP/ON button to select the required character. Each time you press the UP/ON button, the character cycles through the following sequence. ABCDEFGHIJKLMNOPQRSTUVWXYZ?;x/0123456789: -  ., [...]

1-33 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 64 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Viewfinder Ad vanced Men u Bring up the advanced menu pages by setting the POWER switch to ON while pressing the UP/ON button up (see page 52) . There are up to 15 advanced menu pages (the number displ[...]

1-34 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 66 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Item Settings × 1: Uses only the upper REC/TALLY indicator. × 2 (normal value): Uses two REC/TALLY indicators. VF TALLY Selects whether or not to use more than one REC/TALLY indicators in the viewfin[...]

1-35 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 68 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus EZ mode settings The following settings are set for the camera head when EZ mode has been selected. Advanced menu page 8 Item Setting STD CUSTOM Setup file STD Selectable Detail level ±0 Selectable Ma[...]

1-36 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 70 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Video Output and Viewfinder Picture (For DXC-D35WSL/D35WSPL) Subject 2 / 3 -inch optics 4:3 effective area 16:9 effective area Item Settings 16:9/4:3 16:9 VF SCAN AUTO The camera outputs 16:9 video. Th[...]

1-37 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 72 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus To call up files recorded onto a tape (when using the DSR-1/1P) First, connect the DSR-1/1P to the camera head and load the cassette that contains the recorded files. 1 Set the SET UP switch to FILE. 2[...]

1-38 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 74 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus 3 Access advanced menu page 13. a) An asterisk (*) appears in front of any factory preset file whose contents have been revised at least once. 4 Move the cursor to DESTINATION FILE and repeatedly press[...]

1-39 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 76 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus Using SetupNavi and SetupLog with the DSR-1/1P The SetupNavi function records the setup menu and setup files onto a tape, so that the same settings can be called up and used again or copied to another [...]

1-40 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 78 Chapter 4 Viewfinder Screen Indications and Menus Chapter 4 Viewfinder Screen Indications and Menus To abort the data recording while in progress Press the DOWN/OFF button. After the data has been recorded, the following display appears. Viewing SetupLog Data 1 Connect the DSR-1/1P and load the tape [...]

1-41 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 80 Chapter 5 Adjustments and Settings Chapter 5 Adjustments and Settings 4 Arrange a white subject (paper, cloth, etc.) under the same lighting conditions as for shooting, and zoom in on it so that as far as possible the whole screen is white. The minimum white area requirements for the adjustment are s[...]

1-42 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 82 Chapter 5 Adjustments and Settings Chapter 5 Adjustments and Settings If the ATW function does not operate correctly A warning massage appears in the viewfinder as shown in the table below. Message Meaning and corrections to be made If the FILTER control is in position 2, 3 or 4, change it to positio[...]

1-43 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 84 Chapter 5 Adjustments and Settings Chapter 5 Adjustments and Settings 1 Set the SHUTTER switch to the ON position. The SHUTTER indicator in the viewfinder comes on, and it is now possible to change the shutter speed or clear scan frequency setting and to set the EVS function. (If the EVS is already s[...]

1-44 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 86 Chapter 5 Adjustments and Settings Chapter 5 Adjustments and Settings Setting the Cloc k and Timestamping Recor dings Use advanced menu page 8 to set the camera head’s internal clock and record the date and time. Note If the following date/time setting procedure for the internal clock does not caus[...]

1-45 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 88 Chapter 5 Adjustments and Settings Chapter 5 Adjustments and Settings Viewfinder Screen Adjustments The following adjustments are provided to improve the visibility of the viewfinder screen. Although these adjustment may make the viewfinder image clearer, they have no effect on the output video signa[...]

1-46 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 90 Chapter 5 Adjustments and Settings Chapter 5 Adjustments and Settings There are three ways of adjusting the iris: automatically, manually, and with the instant automatic iris adjustment function. Iris adjustment To make the image lighter when shooting against the light In the automatic iris adjustmen[...]

1-47 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 92 Chapter 5 Adjustments and Settings Chapter 5 Adjustments and Settings Settings for special cases The background is very bright, and the subject is too dark. Settings for Special Cases Setting Effect Set the A.IRIS MODE switch to BACK L, turning the indicator on. This lightens the foreground. The subj[...]

1-48 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Appendix 95 Appendix Important Notes on Operation Fitting the zoom lens It is important to fit the lens correctly, as otherwise damage may result. Be sure to refer to the section “Fitting the Lens” (See page 30) . Do not cover the unit while operating Putting a cloth, for example, over the unit can [...]

1-49 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 96 Appendix Appendix Vertical tail on the image Bright object (electric light, sun, etc.) Monitor screen Characteristics of CCD Sensors The following effects may appear in the image. They are characteristic of cameras using CCDs (charge- coupled devices), and do not indicate a malfunction. Vertical smea[...]

1-50 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 98 Appendix Appendix Specifications DXC-D35/D35P/D35WS/D35WSP Camera Head Imaging element Three-chip interline transfer CCD Pixel resolution DXC-D35: 768 (horizontal) × 494 (vertical) DXC-D35P: 752 (horizontal) × 582 (vertical) DXC-D35WS: 980 (horizontal) × 494 (vertical) DXC-D35WSP: 980 (horizontal)[...]

1-51 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 100 Appendix Appendix VTR products DSR-1/1P Digital Videocassette Recorder EVV-9000/9000P Videocassette Recorder PVV-1/1P/1A/1AP/3/3P Portable Videocassette Recorder VO-8800/8800P Portable Videocassette Recorder BVU-150/150P Portable Videocassette Recorder BVV-5/5PS Videocassette Recorder BVW-50/50P Por[...]

1-52 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 102 Appendix Appendix What Is ClipLink? The ClipLink TM function greatly improves the efficiency of the video production process as a whole by recording various editing-related data on tape when shooting. As such, ClipLink is a revolutionary function that transcends the conventional separation of shooti[...]

1-53 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 104 Appendix Appendix Data Generated When Shooting The following describes the kinds of data that is generated when using the ClipLink function. Index Pictures When shooting, a single-frame image from the Mark IN point at the start of each scene is recorded as a still picture into the DSR-1/1P’s inter[...]

1-54 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 106 Appendix Appendix Time codes recorded for Mark IN/OUT points There is a gap between actual time codes and Mark IN/ OUT time codes recorded in the cassette memory, as shown in the figure below. The frame digit is incremented at each Mark IN point and is decremented at each Mark OUT point. Recording c[...]

2-1 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 SW-791 board BP-30 board SW-793 board SW-792 board DC-DC converter CN-1294 board MB-629 board * 1 MB-785 board * 2 ES-32/32(P) board * 1 ES-33/33(P) board * 2 IF-532 board * 1 IF-700 board * 2 CN-1349 board TG-222/222(P) board * 1 TG-223 board * 2 CN-1595 board SE-366 board PA-254 board * 1 PA-254A board[...]

2-2 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2-2. Removal/Attachment of Cabinet 2-2-1. Removal of Side Plate Slacken the eight screws as shown in the figure and remove the right and left side plates. 2-2. Removal/Attachment of Cabinet[...]

2-3 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 CN117 CN120 CN119 CN121 CN123 CN122 CN118 CN103 CN1 CN107 CN106 CN105 CN807 CN805 CN806 CN2 MB board Supports AT board Screws (B3 x 4) Screws (B3 x 4) Connector layout on the MB-629/785 boards Screws (B3 x 6) DC-DC converter Rear plate ES board IF board PR board VA board 2-2-2. Removal/Attachment of Top [...]

2-4 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Screw (K3 x 6) Screw (K3 x 6) Rear plate Front unit assembly Screw (B3 x 10) Screw (B3 x 10) m . Be sure to route the harnesses as shown in the figure when reattaching the MB board. . When reinstalling the VA, PR, IF and ES boards, use care to insert securely the connectors on each board to the connector[...]

2-5 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Front unit assembly Screws with washer (B3 x 10) Screws with washer (B3 x 10) 5. Remove the four screws to remove the front unit assembly. 6. Remove the setscrew shown in the figure and take off the filter knob. 7. Remove the four screws and four washers of the front panel to remove the CCD unit. n Use g[...]

2-6 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 8. Take a new CCD unit out of a transport holder and install it to the unit in the reverse order of steps 1 to 7. 9. Perform the pedestal alignment (in Section 3-3-12), the shading alignment (in Section 3-3-13) and the flare alignment (in Section 3-3-14). m . Before performing alignment, be sure to read [...]

2-7 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 A B 123456789 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2-4. Connectores and Cables 2-4-1. Connector Input/Output Signals The main connector input/output signals are as follows: MONITOR OUT (BNC) ; 1.0 V p-p ± 0.1 V, sync negative 75 Z VIDEO OUT (BNC) ; 1.0 V p-p ± 0.1 V, sync neg[...]

2-8 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 76 57 38 19 58 39 20 1 CAMERA/CA (76P, MALE) (EXTERNAL VIEW) No. Signal I/O Specifications 1 REC TALLY IN Zi > 600 Z 2 S.D. (V/C) IN H : 5 V L : 0 ± 0.5 V 3 SCL VTR IN Zi > 47 k Z Zo < 1 k Z 4 GENLOCK (G) _ GND for GENLOCK (X) 5 SYNC (G) _ GND for SYNC (X) 6 PB (G) _ GND for PB (VBS) (X) 7 PB ([...]

2-9 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 REMOTE (10P, FEMALE) (EXTERNAL VIEW) No. Signal I/O Specifications 1 (SPARE) 2 VBS (RM) OUT 1.0 V p-p, SYNC NEGATIVE 3 VBS (RM) OUT 4 RS232C (C/RM) IN 5 VTR START/STOP IN Zi > 10 k Z OPEN (4.5 ± 0.5 V) 0 ± 0.5 V 6 S. DATA (X) 0 to 5 V Zi > 10 k Z 7 RS232C (RM/C) OUT GND for S. DATA 8 REC TALLY IN[...]

2-10 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 VF (20P, FEMALE) (EXTERNAL VIEW) No. Signal I/O Specifications 1 PEAKING CONT IN Zi > 5 k Z 2 POWER EXT DC OUT 10.5 V to 17.0 V dc, 2 A 3 REC TALLY IND OUT Zo < 500 Z 4 BATT IND OUT Zo < 1.1 k Z 5 ZEBRA SW IN ON : 0 ± 0.5 V 6 VF VIDEO (X) OUT V = 1.0 V p-p 7 POWER EXT DC OUT 10.5 V to 17.0 V d[...]

2-11 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2-4-2. Connection Connector Connections made with the connector panels during installation or service, should be made with the connectors or complete cable assemblies specified in the following list, or equivalent parts. Connector Name Parts No. and name of connector with cable REMOTE 1-506-522-11 CONNE[...]

2-12 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 A A A S102 S101 IC102 ROM IC ROM IC ROM IC – With ROM mounted – – How to attach (Fig. 1) – Push Clearance IC socket cover AT-144 board IC socket cover S102 S101 ON ON OFF 2 1 AT-144 board 2-6. Replacement Way of ROM (IC102) n Perform “RESET” of PAGE 1 in the SERVICE menu after replacing a RO[...]

2-13 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2 1 3 != GND. 8 9 10 4 5 6 7 11 3 2 1 2-8. DC-DC Converter Voltage Voltage values can be check as following 1 to != points on MB board and MIC connector. . MB board (EXTERNAL VIEW) . MIC connector No. CHECK POINT VOLTAGE VALUE 1 CN117-2 pin EXT. DC OUT 2 CN117-1 pin EXT. DC GND 3 CN114-20 pin + 3.1 V 4 [...]

2-14 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2 3 1 2-9. Recommended Replacement Parts Parts listed below are recommended replacement parts. Optical filter unit may be turned cloudy with the lapse of time. If using a cloudy filter, the performance of the camera will not be delivered. Replace it according to necessary. Parts made of rubber used in t[...]

2-15 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Shoe Screws K3 x 6 Screws K3 x 6 Screws K3 x 6 Stop screw Blind plate Plate spring VF connection cable (20pin) Fixing ring Stop screw Shoe Guide plate 2-10. Attaching the 4-type or 5-type Viewfinder An optional 4-type viewfinder (DXF-40 series) or 5-type viewfinder (DXF-50 series) can be attached in acc[...]

2-16 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2-11. Disconnecting/Connecting the Flexible Card Wire The flexible card wires are used among the CN-1294 board and the MB board, the MB board and the TG board. Be careful not to bend these wires. This shortens the wire life. Disconnecting 1. Turn off the power of the camera. Type A (between the MB board[...]

2-17 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2-12. Service Mode Operation This unit has the BASIC menu, ADVANCE menu, SERVICE menu to be operated in the service mode, and FILE menu. . . . . . SERVICE mode To enter the service mode, set the S105 (OPE ↔ ADJ) on the SW-791 board to ADJ. . . . . . Menu select screen When the S105 on the SW-791 board[...]

2-18 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Page Item Standard set value UC PAL 18 FILTER1 3200k 3200k FILTER2 5600k 5600k + 1/8ND + 1/8ND FILTER3 5600k 5600k FILTER4 5600k 5600k + 1/64ND + 1/64ND 19 DIAG ERROR RESET __ MEMORY BACKUP __ 20 Self-diagnosis result display1 11 21 Self-diagnosis result display2 11 22 Self-diagnosis result display3 11 [...]

2-19 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 1 RESET (For DXC-D35/D35WS) Adjusting values such as the electronic volume control of each board except the values differ in every unit can be restored to their standard setting values. Move the cursor to “DEST” position, select “UC,” and move the cursor to “RESET,” then press[...]

2-20 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 5 Camera COMPONENT Level Adjustment . . . . . Page 6 Camera CLAMP Level Adjustment . . . . . Page 7 Chroma/VF Adjustment WY LEV 16:9 Y level adjustment * W R-Y LEV 16:9 R-Y level adjustment * W B-Y LEV 16:9 B-Y level adjustment * Y LEV 4:3 Y level adjustment R-Y LEV 4:3 R-Y level adjustme[...]

2-21 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 10 TEST MODE TEST TEST OFF: TEST SAW TEST: 1 Displays 100 % TEST SAW. TEST: 2 Displays 226 % TEST SAW. TEST: 3 Displays 226 % TEST SAW in the lower side of screen. R-Y ON/OFF control of R-Y output B-Y ON/OFF control of B-Y output . . . . . Page 9 Various Setting 1 (For DXC-D35/D35WS) SETU[...]

2-22 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 11 CCD BLOCK No. Information HEAD1 to 7 CCD block number n Be sure to input the CCD block number which is shown on the side of CCD unit after the replacement of TG board or the EEPROM (IC1) on the TG board. . . . . . Page 12 Sub-Voltage Information . . . . . Page 13 Various Setting 2 R RG[...]

2-23 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 17 Color Temperature Calculation Reference Setting COLOR TEMP CAL. Captures the reference value of color temperature indication R R channel's color temperature indication ; . Reference value setting . Result of capturing the reference value B B channel's color temperature indica[...]

2-24 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 18 FILTER Display Setting FILTER 1 to 4 Make this setting in accordance with a kind of filter attached. n When changing the filter, be sure to make a set. . . . . . Page 19 Self Diagnosis 1 DIAG ERROR RESET This item is used for erasing an error check results and a history of error items.[...]

2-25 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 21 Selfdiagnosis 3 . . . . . Page 20 Selfdiagnosis 2 DISP SELECT The contents of the defective item display are switched. 1: The result of latest error check is displayed. 2: This selfdiagnosis is automatically carried out, and the defective items diagnosed in the past are displayed. PP-P[...]

2-26 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 22 Selfdiagnosis 4 RC-PMPD The details of check result for synchronization signal input and the internal RAM in RC LSI are displayed. 800H: The internal RAM of RC LSI is abnormal. 004H: The input CF signal (IF board IC520, pin63) to the RC LSI is abnormal. 002H: The input HD signal (IF bo[...]

2-27 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 RC-CCR (DXC-D35WS/D35WSP do not have this function.) The details of check result for the connection regarding the CR signal between PR LSI and RC LSI are displayed. 400H: The connection between PR board IC411 pin108 and IF board IC520 pin84 is abnormal. (The No.10 of CR signal) 200H: The connection betw[...]

2-28 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 [Reference] [Reference] [Reference] [Reference] [Reference] If the input of synchronization signal to the PR LSI or RC LSI is abnormal, the connection check between PR LSI and RC LSI also detects the abnor- mality. RC LSI relation check is carried out only when the digital output of DXC- D35/D35P is use[...]

2-29 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 23 Current Status Display Information for production. . . . . . Page 24 TG ROM Operation . . . . . Page 25 Carrier Adjustment When DPR (Dual Pixel Readout) is on. Not in use R D.DARK R Carrier balance adjustment at DPR ON G D.DARK G Carrier balance adjustment at DPR ON B D.DARK B Carrier [...]

2-30 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 2-12-2. File Menu DXC-D35/D35P Reset items and standard values to be set. Standard set value NO.1 NO.2 NO.3 NO.4 NO.5 NO.6 to 8 ITEM STD HISAT FL FILMLIKE SVHS/VHS USER1 to 3 M.BLACK ± 0 ± 0 ± 0 ± 0 ± 0 ± 0 STRETCH ± 0 ± 0 ± 0 ± 0 ± 0 ± 0 M.GAMMA ± 0 ± 0 ± 0 _ 33 ± 0 ± 0 DTL LEV ± 0 +1[...]

2-31 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Standard set value NO.1 NO.2 NO.3 NO.4 NO.5 NO.6 to 8 KNEE APT 24 24 24 63 24 24 HIGH DTL 63 63 63 63 63 63 CCS LEV 5 5 5 5 5 5 STRP1 20 20 20 20 20 20 STRP2 45 45 45 45 45 45 PRSP1 8 8 8 8 8 8 PRSP2 63 63 63 63 63 63 2-12. Service Mode Operation[...]

2-32 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 DXC-D35WS/D35WSP Reset items and standard values to be set. Standard set value NO.1 NO.2 NO.3 NO.4 NO.5 NO.6 to 8 ITEM STD HISAT FL FILMLIKE SVHS/VHS USER1 to 3 M.BLACK ± 0 ± 0 ± 0 ± 0 ± 0 ± 0 STRETCH ± 0 ± 0 ± 0 ± 0 ± 0 ± 0 M.GAMMA ± 0 ± 0 ± 0 _ 33 ± 0 ± 0 DTL LEV ± 01 0 ± 0 _ 80 _ 5[...]

2-33 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Standard set value NO.1 NO.2 NO.3 NO.4 NO.5 NO.6 to 8 KNEE APT 24 24 24 63 24 24 HIGH DTL 63 63 63 63 63 63 CCS LEV 5 5 5 5 5 5 STRP1 20 20 20 20 20 20 STRP2 45 45 45 45 45 45 PRSP1 8 8 8 8 8 8 PRSP2 63 63 63 63 63 63 2-12. Service Mode Operation[...]

2-34 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 1 All Reset (For DXC-D35/D35WS) Each item value in all FILE can be restored to their standard setting (factory setting). . . . . . Page 2 File Name Change/File Reset FILE NO. File No. of operation item FILE NAME File name of operation item file FILE RESET Performing of FILE RESET FILE Fil[...]

2-35 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 4 File Basic Setting M.BLACK Master black level setting STRETCH Black stretch level setting M GAMMA Master GAMMA level setting DTL LEV Detail level setting V DTL LEV V detail level setting DTL FREQ Detail center frequency setting FILE DATA selected with SET UP switch is displayed on the P[...]

2-36 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 . . . . . Page 8 File Matrix Variable Width Setting R-G WIDTH HUE variable width of R-G coefficient setting R-B WIDTH HUE variable width of R-B coefficient setting G-R WIDTH HUE variable width of G-R coefficient setting G-B WIDTH HUE variable width of G-B coefficient setting B-R WIDTH HUE variable width[...]

2-37 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 PAGE12 (NEXT PREV ) FILE STORE FILE DISTINATION FILE USER1 STORE FILE (YES ) : * HISAT EXIT MENU (YES ) . . . . . Page 12 File Store FILE File name to be recalled DESTINATION FILE Selection of FILE STORE destination STORE FILE Performing of FILE STORE 2-12. Service Mode Operation[...]

[...]

3-1 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-1. Preparation 3-1-1. Equipment Required . Digital voltmeter . Oscilloscope (100 MHz or more) . Vectorscope . Waveform monitor . B/W monitor (Sony PVM-91/122 or equivalent) . Color monitor (Sony PVM-1320 or equivalent) . AC Adaptor (Sony CMA-8/8A/8CE/8ACE) . Camera Adaptor (Sony CA-537/537P) . Frequenc[...]

3-2 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-1-4. Notes on Adjustment . Before adjustment, be sure to perform 10-minute warm- up. . When using the SERVICE menu and FILE menu, refer to “2-12. Service Mode Operation”. . To shoot the chart frame covering fully the underscanned monitor frame, perform the following procedures. 1. Set the camera to[...]

3-3 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Light source Chart Illuminance meter 3-1-5. Maintaining the Grayscale Chart For the CCD OUT level adjustment and the Gamma correction adjustment, using an 89.9 %-reflective grayscale chart is preferable. If a reflective chart is not available, use a well-maintained pattern box and a transparent grayscale[...]

3-4 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 Chart Luminance meter 1 m Setting luminous intensity (when the transparent chart is used) Equipment: Luminance meter (Minolta LS-110 or equivalent. Calibrated.) 1. Light the pattern box and warm up for about 30 minutes. 2. Place the pattern box where the chart is not exposed to light, such as a darkroom.[...]

3-5 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-2. Before Adjustment 3-2-1. Color Bar Signal Confirmation Equipment: Waveform monitor, Vectorscope Preparation: OUTPUT/DL/DCC+ switch: BARS Test point: VIDEO OUT connector Specification: [for NTSC] [for PAL] . Chroma Level Confirm that the beam spots of each color (R, Y L , G, C Y , G, B and M G ) are [...]

3-6 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 R M G C Y G Y L B R M G C Y G Y L B Burst HH Burst 3-3. Camera Adjustment n Before the adjustment, enter the “PAGE 1” of SERVICE menu, and perform the “RESET”. 3-3-1. Sub-Carrier Frequency Adjustment Equipment: Frequency counter To be extended: ES-32 board (for DXC-D35/D35P) ES-33 board (for DXC-[...]

3-7 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-3-3. Y/R-Y/B-Y CLP Level Adjustment Equipment: Oscilloscope To be extended: IF-532 board (for DXC-D35/D35P) IF-700 board (for DXC-D35WS/D35WSP) Preparation: OUTPUT/DL/DCC + switch: BARS Test point: TP60, 61, 62 (GND: TP63) /EX-490 board Trigger: HD (TP83/EX-490 board) Adjustment Procedure 1. Select “[...]

3-8 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 R M G C Y G Y L B R M G C Y G Y L B 75% 100% 75% Item Test Point Specification Y LEV TP61 NTSC: A = 714 ± 10 mV F = 54 ± 5 mV PAL: A = 700 ± 10 mV * W Y LEV TP61 NTSC: A = 714 ± 10 mV PAL: A = 700 ± 10 mV SYNC LEV TP61 NTSC: B = 286 ± 5 mV PAL: B = 300 ± 5 mV R-Y LEV TP60 NTSC: C = 700 ± 20 mV PA[...]

3-9 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 TP501 RV501 RV502 RV503 RV504 RV505 E501 FL502 CN501 1 2 3 4 5 6 A B C D ES-32 board (A side) (DXC-D35/D35P) ES-33 board (A side) (DXC-D35WS/D35WSP) 3-3-6. Chroma (VBS) Level Adjustment n Use the vectorscope conforming to setup “7.5 IRE”. (for NTSC) Equipment: Verctorscope To be extended: ES-32 board[...]

3-10 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-3-7. Y (VBS) Level Adjustment Equipment: Waveform monitor To be extended: ES-32 board (for DXC-D35/D35P) ES-33 board (for DXC-D35WS/D35WSP) Preparation: OUTPUT/DL/DCC+ switch: BARS Test point: VIDEO OUT connector Adjustment Procedure 1. [for NTSC] . SERVICE menu “PAGE 9” → SET UP : ON [for PAL] [...]

3-11 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 B A B A 3-3-10. VF SYNC/BLKG Level Adjustment Equipment: Oscilloscope To be extended: ES-32 board (for DXC-D35/D35P) ES-33 board (for DXC-D35WS/D35WSP) Preparation: OUTPUT/DL/DCC + switch: BARS Test point: TP82 (GND: TP83)/EX-490 board Trigger: HD (TP84/EX-490 board) Adjustment Procedure 1. SERVICE menu[...]

3-12 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-3-11. CCD Output Level Adjustment m . Usually, this adjustment is not required. Only when the output level of CCD unit is largely different from the specification, make the adjustment. . When the new CCD unit for spare parts is replaced, this adjustment is not required because of the correct adjust- m[...]

3-13 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 R M G C Y G Y L B R M G C Y G Y L B 75% 100% 75% 3-3-12. Carrier Adjustment at DPR (Double Pixel Reading) ON Equipment: Waveform monitor, Vectorscope (MAX GAIN) Preparation: . HYPER GAIN switch: ON . OUTPUT/DL/DCC + switch: CAM/DCC + Test point: VIDEO OUT connector Adjustment Procedure 1. SEVICE menu ?[...]

3-14 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3. Adjust the lens iris to bring the white level “A” to 70 ± 2 IRE. Test point: VIDEO OUT connector 4. In the following items, by pressing the UP or DOWN switches, adjust the waveform of the oscilloscope to be flat. GND: TP38/EX-490 board Item Test point Specification R W. SHAD CL101 G W. SHAD CL20[...]

3-15 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-3-15. MIC Level/MIC Level IND Adjustment Equipment: Oscilloscope Preparation: OUTPUT/DL/DCC+ switch: BARS Adjustment Procedure MIC Level Adjustment Test point: CL201 (GND: Capacitor C202 + side) /MB-629 board (for DXC-D35/D35P) /MB-785 board (for DXC-D35WS/D35WSP) Adjusting point: 1 RV201 /MB-629 boar[...]

3-16 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 CV1 CV3 (DXC-D35WS/D35WSP only) B C D E F G 6 4 3 2 1 MB-629 board (B side) (DXC-D35/D35P) MB-785 board (B side) (DXC-D35WS/D35WSP) 5 CL201 A RV201 C202 + 3-3-16. Character Position Adjustment Equipment: Color monitor (or, B/W monitor) Preparation: OUTPUT/DL/DCC + switch: BARS Test point: MONITOR OUT co[...]

3-17 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-3-17. 4 : 3 Title Adjustment (Only for DXC- D35WS/D35WSP) Equipment: Color monitor (or, B/W monitor) Preparation: OUTPUT/DL/DCC + switch: BARS Test point: MONITOR OUT connector Adjustment Procedure 1. Select “PAGE 9” on the ADVANCE menu, set “16:9/4:3” to “4:3” position. 2. Select “PAGE [...]

3-18 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-4. Changing the Standard Setting Values (Video Level) When changing the setting of black level, flare, gamma, manual knee and white clip by the user’s desire, perform the procedures below. 3-4-1. Setting Status before Changing the Setting. . . . . . Side Panel GAIN switch: LOW (0 dB) OUTPUT/DL/DCC +[...]

3-19 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 3-4-3. Changing the Flare Compensation Setting Value Object: Grayscale chart Equipment: Waveform monitor Preparation: Select a large lens iris and shoot the grayscale chart covering fully the underscanned frame. Test point: VIDEO OUT connector Procedure for changing the setting 1. SERVICE menu “PAGE 3[...]

3-20 DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1 [Reference] [Reference] [Reference] [Reference] [Reference] In STD, HISAT, FL, FILMLIKE, SVHS/VHS and USER1 to 3 files, the manual knee setting is available in every file. To return the changed manual knee setting values to the standard setting values, perform the following procedures. (1) Set SETUP swi[...]

[...]

Printed in Japan Sony Cor por ation 2000. 4 08 Communication System Solutions Network Compan y ©2000 DXC-D35 (UC) DXC-D35P (CE) DXC-D35WS (UC) DXC-D35WSP (CE) E 9-955-214-11[...]