Sony HDW-M2000P manuel d'utilisation

HD DIGIT AL VIDEOCASSETTE RECORDER HD W -2000 HD W -M2000 HD W -M2000P OPERA TION MANUAL [English] 1st Edition (Revised 5) Serial No. 16001 and Higher (HDW-2000/M2000) Serial No. 46001 and Higher (HDW-M2000P)[...]

W ARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. A VER TISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humi[...]

WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES. 1. Use the approved Power Cord (3-core mains)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable. 2. Use the Power Cord (3-core mains lead)/Plug conforming to the following ratings, which meets power supply voltage of each cou[...]

Table of Contents 1 Chapter 1 Overview Ta b le of Contents 1-1 F ea tur es ........................................................................................... 1-1 1-2 Example System Configuration .................................................... 1-4 Chapter 2 Location and Function of P ar ts 2-1 Control P anels ..........................[...]

Ta b le of Contents 2 Table of Contents Chapter 6 Shot Mark Function 6-1 Overview ......................................................................................... 6-1 6-2 Shot Mark Operation Menu .......................................................... 6-2 6-3 Shot Mark Operations .........................................................[...]

Chapter 1 Overview Chapter 1 Overview 1-1 1-1 Features Chapter 1 Overview The HDW-2000/M2000/M2000P is a high-definition (HD) digital videocassette recorder based on the HDCAM format. This unit uses large scale integrated circuits for signal processing, and has a simple internal construction, allowing it to provide functionality at least equivalent[...]

Chapter 1 Overview 1-2 Chapter 1 Overview 1-1 Features Basic operation buttons and jog/shuttle dial The basic buttons and jog/shuttle dial for VTR and editing operations are provided in the conventional VTR layout, ensuring continuity with conventional operating panels. Time data display This can be selected to display a CTL counter value, time cod[...]

Chapter 1 Overview Chapter 1 Overview 1-3 Remote control function This unit can be controlled from an external remote controller or editor through an interface complying with RS-422A (serial 9-pin). Since two remote control connectors are provided, you can also control a number of VTRs simultaneously. Additionally, a parallel (50-pin) interface is [...]

Chapter 1 Overview 1-4 Chapter 1 Overview 1-1 Features The following conceptual diagram shows an example of use. 1-2 Example System Configuration Digital cassette BVE-series editor Tape control HDSDI/Analog composite Audio monitor Analog composite/component Video monitor Audio/video server system SDTI (optional) HDSDI SDI Analog audio HDW-2000/M200[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-1 2-1 Contr ol P anels There are three control panels, as follows: •U pper control panel • Lower control panel •S witch panel Chapter 2 Location and Function of P ar ts Z CTL/TC EE TC MENU 59.94 PB/EE CONFI DISABL TCGSET VID. IN SDI ON OFF KEY INHI FRONT REAR [...]

Chapter 2 Location and Function of Parts 2-2 Chapter 2 Location and Function of Parts 2-1-1 Upper Contr ol Panel Z 1(9P) 2(50P) RS-232C HDCAM Digital BET ACAM MPEG IMX BET ACAM SX BET ACAM/SP POWER PHONES REMOTE EJECT 1 POWER switch 2 REMOTE buttons and RS-232C indicator 4 Format indicators 5 PHONES jack and control Cassette compartment 1 POWER swi[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-3 2-1-2 Lower Contr ol P anel CTL/TC TC MENU VID. IN PB/EE CONFI SDI DISABL EE TCGSET 59.94 EE TC VID. IN PB/EE CONFI SDI DISABL TCGSET CTL/TC MENU 59.94 1 Audio control section (see page 2-4) 2 CHANNEL CONDITION indicator (see page 2-6) 3 Menu control buttons (see [...]

Chapter 2 Location and Function of Parts 2-4 Chapter 2 Location and Function of Parts 1 Audio control section 1 Audio selection function selector buttons INPUT (input signal selection mode) button: Pressing this button puts the unit into input signal selection mode. In the audio setting display section, indicators flash to indicate the currently se[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-5 DATA indicator: Lights when the audio output signals are recognized as data with the unit in recording, E-E 1) , or playback mode. OVER indicator: While the unit is in recording or playback mode, this lights when the level of the audio signal on the corresponding [...]

Chapter 2 Location and Function of Parts 2-6 Chapter 2 Location and Function of Parts 2-1 Contr ol Panels 5 REC (recording) controls These individually adjust the recording levels on channels 1 to 4, and cue audio. To set the recording level, put the unit into E-E mode, press to protrude the control knobs and adjust the level while watching the lev[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-7 4 Time data/menu display section 1 Time data display This displays indicators relating to time data and other indicators. Time data display area 1 Normally this displays a CTL count, time code value, or user bit value according to the setting in function menu HOME[...]

Chapter 2 Location and Function of Parts 2-8 Chapter 2 Location and Function of Parts CONFI (ON)/PREREAD indicators These indicate the state of the VTR CONFI playback 1) function. When the CONFI playback function is enabled, the CONFI indicator appears, and when CONFI playback is actually being carried out the ON indicator also appears. When F6 (PR[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-9 1 SHUTTLE button To use the search dial for playback in shuttle mode, press this button, turning it on. For details of playback in shuttle mode, see the description of the search dial 5 . 2 JOG button To use the search dial for playback in jog mode, press this but[...]

Chapter 2 Location and Function of Parts 2-10 Chapter 2 Location and Function of Parts RECINH setting State of the record inhibit plug on the cassette REC INHI indicator state ON Record inhibit/permit Lit OFF Record inhibit Lit a) Record permit Off PREROLL REW PLAY F FWD STOP REC EDIT STANDBY 2 REC button 3 EDIT button 4 STANDBY button 1 PREROLL bu[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-11 5 STOP button To stop recording or playback, press this button, turning it on. When you stop playback, the unit switches either to still playback or to E-E mode according to the setting on function menu HOME page for F2 (PB/EE) and the setting of setup menu item [...]

Chapter 2 Location and Function of Parts 2-12 Chapter 2 Location and Function of Parts qd Editing control section 1 DMC EDIT button Use this button to memorize the playback speed varied between –1 and +2 times normal speed, and carry out automatic playback or automatic editing using the memorized playback speed. 2 MEMORY indicator When memorizing[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-13 4 TRIM buttons Use these buttons to trim an edit point to single-frame precision. Hold down the IN, OUT, AUDIO IN, or AUDIO OUT button, and press one of these buttons. The ‘+’ button advances the corresponding edit point by one frame, and the ‘–’ button[...]

Chapter 2 Location and Function of Parts 2-14 Chapter 2 Location and Function of Parts 2-1-3 Switch P anel To access the switch panel, open the lower control panel. On how to open the lower control panel, see the figure on page 2-1. ON OFF KEY INHI FRONT REAR P ANEL SEL CONTROL P ANEL 5 KEY INHIBIT switch 4 PANEL SELECT switch 3 CONTROL PANEL conne[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-15 2-2 Connector P anel 75 Ω Cooling fan Cooling fan 1 Analog audio input/output section 2 Analog video input/output section (see page 2-16) 3 Digital audio input/output section (see page 2-16) 4 Digital signal input/ output section (see page 2-17) 5 Power supply [...]

Chapter 2 Location and Function of Parts 2-16 Chapter 2 Location and Function of Parts 2-2 Connector P anel 2 Analog video input/output section 1 REF. (reference) VIDEO INPUT connectors (BNC type) and 75 Ω termination switch Input a reference video signal. Input a three-valued (positive and negative) sync signal, a video signal with chroma burst [...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-17 4 Digital signal input/output section 1 HDSDI (HD Serial Digital Interface) INPUT connectors (BNC type) The upper of these two connectors inputs HD format video/audio signals. The lower one outputs the input signals for monitoring. 2 HDSDI (HD Serial Digital Inte[...]

Chapter 2 Location and Function of Parts 2-18 Chapter 2 Location and Function of Parts 2-2 Connector P anel 1 REMOTE 2 PARALLEL I/O(50P) connector (D-sub 50-pin) Connect remote control signals from an external device. For details, refer to the Installation Manual. 2 CONTROL PANEL connector (round type, 10- pin) In addition to the lower control pane[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-19 1 MONITOR OUTPUT R connector (XLR 3-pin, male) This outputs the audio signals whose output destination was set to ‘R’ with the audio signal selection buttons in the audio control section. If multiple tracks have been set to ‘R’, the signals of those track[...]

Chapter 3 Preparations Chapter 3 Preparations 3-1 This unit can input serial digital signals (video and audio) from another digital VTR such as the HDW- 500/F500/2100/M2100/M2100P. The following 75 Ω 75 Ω REMOTE 1-IN(9P) REMOTE 1-OUT(9P) HDSDI OUTPUT SDI OUTPUT 3 HDSDI INPUT REF . VIDEO INPUT REF . VIDEO INPUT REF . VIDEO INPUT 3-1 Connections [...]

Chapter 3 Preparations 3-2 Chapter 3 Preparations 3-2 Reference Sync Signals This section describes how reference signals for the video output signals and servo system are selected. The output from the internal reference video signal generator is supplied to the output video signal and servo circuits as a reference signal. 3-2-1 Selecting Reference[...]

Chapter 3 Preparations Chapter 3 Preparations 3-3 HDSDI INPUT REF . VIDEO INPUT HDSDI OUTPUT REF . VIDEO INPUT •C onnections for recording from a switcher or signal generator •C onnections for recording from an external VTR (player) 3-2-2 Connecting Reference Signals Connect reference signals as shown below, according to the way in which the un[...]

Chapter 3 Preparations 3-4 Chapter 3 Preparations •C onnections for playback • SDI OUTPUT • COMPOSITE • COMPONENT REF . VIDEO INPUT HDSDI OUTPUT 75 Ω HD video monitor SD video monitor HDW-2000/M2000/M2000P 75 Ω termination switch: ON Reference signal 3-2 Reference Sync Signals[...]

Chapter 3 Preparations Chapter 3 Preparations 3-5 3-3 Setup The principal setup operations before operating this unit can be carried out using setup menus. The setup menus of this unit comprise a basic setup menu and an extended setup menu. The contents of these menus are as follows. Basic setup menu: • Items relating to the hours meter • Items[...]

Chapter 3 Preparations 3-6 Chapter 3 Preparations 3-4 Superimposed Character Inf ormation When the function menu item CHARA is set to ON, the video signal output from the HDSDI OUTPUT 3 (SUPER) connector, SDI OUTPUT 3 (SUPER) connector, or COMPOSITE VIDEO OUTPUT 3 (SUPER) connector contains superimposed character information, including time code, m[...]

Chapter 3 Preparations Chapter 3 Preparations 3-7 2 Time code reader drop frame mark (for 59.94i, 29.97PsF mode only) “.”: Indicates drop frame mode “:”: Indicates non-drop-frame mode 3 Time code generator drop frame mark (for 59.94i, 29.97PsF mode only) “.”: Indicates drop frame mode (factory preset) “:”: Indicates non-drop-frame m[...]

Chapter 3 Preparations 3-8 Chapter 3 Preparations 3-5-1 Cassette T ypes This unit uses the following HDCAM cassettes for both recording and playback. HDCAM cassettes The HDW-M2000/M2000P can also play back the following cassettes. •D igital Betacam cassettes •M PEG IMX cassettes •B etacam SX cassettes •B etacam SP cassettes (metal tape) •[...]

Chapter 3 Preparations Chapter 3 Preparations 3-9 Large cassette Small cassette Press in the red record inhibit plug. (“ON”) Return this plug to its original position to enable recording on the tape again. (“OFF”) 3-5-3 Preventing Accidental Erasure of Recor dings To prevent a tape from being inadvertently erased, press in the red record in[...]

Chapter 3 Preparations 3-10 Chapter 3 Preparations 3-6 Using a Memory Stic k When a Memory Stick is inserted in the VTR, the file data can be stored on the Memory Stick , which enables you to share data among cameras. Note Use a Memory Stick formatted with this VTR. It cannot be shared with other devices. For more details, refer to the Maintenance [...]

Chapter 3 Preparations Chapter 3 Preparations 3-11 Notes • Prevent metallic objects or your finger from coming into contact with the terminal of the connecting section. •D o not attach any material other than the supplied label to the label space. •A ttach the label at the prescribed labeling position. Make sure the label is attached at the l[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-1 4-1 Recor ding Chapter 4 Recor ding and Pla ybac k This section describes video and audio recording on the unit. 4-1-1 Preparations f or Recording Switch and menu settings Before beginning recording, make necessary switch and menu settings. For details on each setting, see the pa[...]

Chapter 4 Recording and Playback 4-2 Chapter 4 Recording and Playback Adjusting the audio recording levels When carrying out audio recording at a reference level Leave the REC controls pressed in. The audio signals will be recorded at a preset reference level (a reference –20 dB indication for an input of +4 dBm). Manually adjusting the recording[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-3 Setting an initial time code value Use the following procedure. 1 Set the CTL/TC to TC. 2 Press the F6 (TCGSET) button. The function menu display changes as follows. SET EXIT TCG SET 00 : 00 : 00 : 00 The first digit of the time code value (8 digits: hours, minutes, seconds, and [...]

Chapter 4 Recording and Playback 4-4 Chapter 4 Recording and Playback • To synchronize to LTC data contained in the HDSDI signal input to this unit: TCG (F1): SDI PR/RGN (F2): LTC • To synchronize to VITC data contained in the HDSDI signal input to this unit: TCG (F1): SDI PR/RGN (F2): VITC This starts the internal time code generator running i[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-5 4-2 Pla ybac k This section describes playback of video and audio. 4-2-1 Preparations f or Playbac k Switch and menu settings Before beginning playback, make necessary switch and menu settings. For details on each setting, see the pages indicated in parenthesis. Z EE TC VID. IN P[...]

Chapter 4 Recording and Playback 4-6 Chapter 4 Recording and Playback 4-2 Pla ybac k Time data selection Displayed time data Use the CTL/TC setting in function menu HOME page to select one of CTL (control), time code, and user bit values. When you select time code, the data displayed is determined by the F6 (TCR) setting (LTC/AUTO/ VITC) in functio[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-7 Playback in jog mode In jog mode, you can control the speed of playback by the speed of turning the search dial. The playback speed range is ±1 times normal speed. The playback speed range can be ±3 times normal speed by changing the setting of setup menu item 116. To carry out[...]

Chapter 4 Recording and Playback 4-8 Chapter 4 Recording and Playback 4-2 Pla ybac k To alternate between normal-speed playback and shuttle mode playback Set the search dial to the position corresponding to the desired shuttle playback speed, then switch between normal-speed playback and shuttle playback by pressing the PLAY and SHUTTLE buttons alt[...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-9 To perform continuous capstan override playback 1 Set setup menu item 111 (TSO PLAY) to TSO. 2 Hold down the DMC EDIT button and turn the MULTI CONTROL knob to select the playback speed. The selected playback speed is displayed in time data display area 2 on the lower control pan[...]

Chapter 4 Recording and Playback 4-10 Chapter 4 Recording and Playback 4-2 Pla ybac k Storing a varying playback speed in memory To store the playback speed for DMC playback, use the following procedure. 1 Press the DMC EDIT button, turning it on. 2 Either while playing back the recorded tape, or during recording, press the ENTRY button and one of [...]

Chapter 4 Recording and Playback Chapter 4 Recording and Playback 4-11 3 Press the search dial or the SHUTTLE button or VAR button to enter shuttle/variable speed mode. The SHUTTLE/VAR indicator lights. Note Make sure that setup menu item 111 (TSO PLAY) is set to DIS. 4 Holding down the DMC EDIT button, turn the search dial, to set the initial spee[...]

Chapter 4 Recording and Playback 4-12 Chapter 4 Recording and Playback To start playback immediately after preroll Press the PREVIEW button. The PREVIEW button lights, and after preroll, DMC playback is carried out for the section from the speed variation start point, then playback continues at normal speed from the speed variation end point. To st[...]

Chapter 5 Editing Chapter 5 Editing 5-1 5-1 A utomatic Editing Chapter 5 Editing This section describes how to carry out automatic editing with this unit and another VTR connected to the REMOTE1-IN(9P) connector. 5-1-1 Overview Editing mode With this unit, you can use the following two edit modes for automatic editing. • Assemble editing This is [...]

Chapter 5 Editing 5-2 Chapter 5 Editing 5-1 A utomatic Editing Z EE TC VID. IN PB/EE CONFI SDI DISABL TCGSET CTL/TC MENU 59.94 5-1-2 Switch and Men u Settings Before beginning editing, make necessary switch and menu settings. POWER switch: ‘ I ’ side (on) Audio selection function selector buttons (see page 2-4) : Select the input audio signal. [...]

Chapter 5 Editing Chapter 5 Editing 5-3 5-1-3 Selecting the Editing Mode To select the editing mode Select assemble editing or insert editing. Depending on the editing mode, press the following button or buttons. • For assemble editing: ASSEMBLE button • For insert editing: the desired INSERT buttons (VIDEO, CH1 to CH4, CUE, and TC) When you se[...]

Chapter 5 Editing 5-4 Chapter 5 Editing 5-1 A utomatic Editing Setting split edit points In split editing, you can set the edit points for audio and video independently. Set the audio edit points with the AUDIO IN/OUT buttons, and the video edit points with the IN/OUT buttons. Note that split editing is only possible when the recording mode is inse[...]

Chapter 5 Editing Chapter 5 Editing 5-5 When the audio IN point is not set for insert editing of audio only As long as the audio OUT point is set, the VTR is ready for preview or editing. If the audio IN point has not been set, the current tape position is automatically used as the audio IN point. Using a VTR without a split editing function as the[...]

Chapter 5 Editing 5-6 Chapter 5 Editing 5-1 A utomatic Editing 5-1-5 Modifying and Deleting Edit P oints If the edit points are not set correctly, for example if an OUT point is before a corresponding IN point, the DELETE button flashes, and it is not possible to carry out a preview or editing operation. In this case, either modify the erroneous ed[...]

Chapter 5 Editing Chapter 5 Editing 5-7 5-1-6 Cue-up to Edit P oints and Prer oll To preroll for the edit IN point or to cue up to any edit point, use the following procedure. 1 Press the RECORDER button or PLAYER button to select the VTR on which you wish to operate. The button you have pressed lights. 2 • To cue up to an edit point Hold down th[...]

Chapter 5 Editing 5-8 Chapter 5 Editing 5-1 A utomatic Editing 5-1-8 Carrying Out A utomatic Editing Monitor output During a preview, on a monitor connected to the recorder you can monitor the following video and audio. • From the preroll point to the IN point, you can monitor the playback from the recorder. • From the IN point to the OUT point[...]

Chapter 5 Editing Chapter 5 Editing 5-9 The following figure illustrates this. Using a single monitor for video and audio on both player and recorder For efficient editing if only one monitor is available, use the following method. 1 Connect the monitor to the recorder. 2 In the basic setup menu, set item 008 to AUTO. 3 Press the PLAYER button on t[...]

Chapter 5 Editing 5-10 Chapter 5 Editing 5-1 A utomatic Editing After automatic editing, to adjust the edit points and reexecute the edit Hold down the DELETE button and press the ENTRY button to recall the edit points. After adjusting the edit points, press the AUTO EDIT button to carry out the edit again. For details of how to adjust edit points,[...]

Chapter 5 Editing Chapter 5 Editing 5-11 5-2 DMC Editing By controlling the player playback speed from the recorder, you can achieve variable speed editing. 5-2-1 Overview of DMC Editing Conditions for DMC editing DMC editing can be used for insert or assemble editing, but not for audio split editing. Tape movement during DMC editing The following [...]

Chapter 5 Editing 5-12 Chapter 5 Editing 5-2-2 Carrying Out DMC Editing Setting the edit points and player speed Use the following procedure. 1 Press the ASSEMBLE button or the desired INSERT button to select the editing mode. 2 Press the DMC EDIT button. This unit switches to the DMC editing mode, and the DMC EDIT button lights. 3 Press the RECORD[...]

Chapter 5 Editing Chapter 5 Editing 5-13 This section describes the following automatic editing methods: •Q uick editing •C ontinuous editing • Standalone editing •M anual editing • Preread editing 5-3-1 Quic k Editing After selecting the edit mode, you can save on editing time by setting the edit points and executing the edit at the same[...]

Chapter 5 Editing 5-14 Chapter 5 Editing 5-3-3 Standalone Editing This refers to editing using as the player an external device which cannot be controlled remotely through the REMOTE1-IN(9P) connector. For example, you can record a color bar signal from a signal generator in the joints between the scenes of an already completed tape. Carrying out s[...]

Chapter 5 Editing Chapter 5 Editing 5-15 Notes • In preread editing, if an input video signal is used as the reference signal for the output video signal, this forms a feedback loop. To prevent the occurrence of feedback, set the F2 (OUTREF) (see page 9-7) in function menu page 4 to REF, and set item 309 in the extended setup menu to AUTO1 (see p[...]

Chapter 6 Shot Mark Function Chapter 6 Shot Mark Function 6-1 First, the shot mark functions of this unit are described in simple terms. Reading shot marks This unit reads in shot marks written on a tape and stores them in memory (to a maximum of 200). Once this data is stored in this unit, it is preserved even when the power is turned off. Writing[...]

Chapter 6 Shot Mark Function 6-2 Chapter 6 Shot Mark Function This section describes the settings in the shot mark operation menu. Displaying the shot mark operation menu With the function menu HOME page showing in the menu display, hold down the MARK button, and press the F5 (MENU) button. The following menu appears on the monitor. GO1:SEARCH TYPE[...]

Chapter 6 Shot Mark Function Chapter 6 Shot Mark Function 6-3 This section describes the operations concerning reading and writing shot marks. Note that the following operations cannot be carried out by remote control. 6-3-1 Reading Shot Marks To read in shot marks With a cassette loaded, hold down the LIST button and press the F FWD or REW button.[...]

Chapter 6 Shot Mark Function 6-4 Chapter 6 Shot Mark Function To write in crash recording or assemble editing 1 Hold the MARK button down for at least 2 seconds. 2 At the position you wish to write the mark, hold down the ENTRY button, and press the MARK button. A mark of the type selected in item G04 of the shot mark operation menu is written. Wri[...]

Chapter 6 Shot Mark Function Chapter 6 Shot Mark Function 6-5 Example of list display The following figure shows how the list is organized. Selecting a shot mark Turn the MULTI CONTROL knob to align the asterisk cursor with the desired shot mark. Entering virtual shot marks When the unit is stopped, performing playback, or searching with the REC/ER[...]

Chapter 6 Shot Mark Function 6-6 Chapter 6 Shot Mark Function To delete an individual shot mark Use the following procedure. 1 With the shot mark list displayed, select the shot mark to be deleted using the MULTI CONTROL knob. 2 Hold the MARK button down. While you hold down the button, an “X” appears after the selected shot mark number, indica[...]

Chapter 6 Shot Mark Function Chapter 6 Shot Mark Function 6-7 Cuing up to shot marks adjacent to the current tape position (index function) 1 In item G01 of the shot mark operation menu (page 6-2) , select one of recording start mark, shot mark 1, shot mark 2, and post mark, or select all. 2 Holding down the MARK button, press the F FWD button or R[...]

Chapter 6 Shot Mark Function 6-8 Chapter 6 Shot Mark Function 6-3 Shot Mark Operations 6-3-6 Sorting Shot Marks Based on shot data recorded on the tape, you can separate the shot marks by cassette, and sort them in time code sequence. To sort the shot marks Use the following procedure. Z 3 21 1 With the shot mark list displayed, press the F5 (SETIN[...]

Chapter 7 Tele-File 7-1 Chapter 7 Tele-File Chapter 7 T ele-File 7-1 Overview of T ele-File Functions Tele-File is a non-contact data carrier system. Tele-File enables data writing/reading between cassettes with memory labels and VTRs. It increases the efficiency of operations such as recording, playback and editing, and source data management. New[...]

7-2 Chapter 7 Tele-File Chapter 7 Tele-File 7-2 Opening the T ele-File Men u Opening from the function menu Display page 5 of the function menu in the menu display section, and then press the F1 (TELE-F) button. The Tele-File menu opens. For details about the function menu, see Chapter 9 “Function Menu” (page 9-1). Opening automatically When se[...]

Chapter 7 Tele-File 7-3 Chapter 7 Tele-File 7-3 T ele-File Menu 7-3-1 Clip Data Displa y How to read the display Shown below are examples of the default menu displays in the menu display section and the monitor display. For more information about how to display menus on the monitor, see the section “To display menus on the monitor” (page 10-2).[...]

7-4 Chapter 7 Tele-File Chapter 7 Tele-File Setting display area Displays the setting of the currently selected data type, and a cursor (“*” or “>”). The meaning of the cursor symbols is as follows: *: Indicates that the mode is clip data display mode or attribute data display/modify mode, and that data is selected. >: Indicates that [...]

Chapter 7 Tele-File 7-5 Chapter 7 Tele-File Monitor display Title The title (maximum 14 characters) set in attribute data display/modify mode. Selected clip number A 4-digit number representing the number of the selected clip (with the “*” cursor). Remaining memory percentage The percentage of remaining memory (user area) available for use. If [...]

7-6 Chapter 7 Tele-File Chapter 7 Tele-File Moving the cursor directly Regardless of the cursor’s current position, pressing one of the following buttons moves the cursor directly to the specified position in the same clip and displays the data. IN (video IN point) button: IN point data OUT (video OUT point) button: OUT point data MARK button: Cu[...]

Chapter 7 Tele-File 7-7 Chapter 7 Tele-File 7-3-3 Modifying Clip Data To modify clip data, put the unit into clip data display mode and then press the F2 (SELECT) button to put it into clip data modification mode (the cursor changes to “>”). The function assignments for menu items in clip data modification mode are as follows. Clip data modi[...]

7-8 Chapter 7 Tele-File Chapter 7 Tele-File To add and delete clips To add clips 1 Rotate the MULTI CONTROL knob to move the “*” cursor to the position where you want to insert the clip. 2 Press the F2 (SELECT) button. The unit enters clip data modification mode. 3 Press the F5 (INS LN) button. A confirmation message “INSERT CLIP OK?” appea[...]

Chapter 7 Tele-File 7-9 Chapter 7 Tele-File To set the set or modified data as other time data Press the F6 (SET TO) button and select the time data (cue point, IN point, or OUT point), and then press the F5 (SET) or F6 (SET NL) button. The position where the data is set differs as follows, depending on the button pressed. • F5 (SET): The data is[...]

7-10 Chapter 7 Tele-File Chapter 7 Tele-File To make comment settings Proceed as follows to make comment settings. 1 Select a clip. 2 Select comment. 3 Press the F2 (SELECT) button. The unit enters clip data modification mode. 4 Press the F2 (MODIFY) button. The data entry area begins to flash, and the data can be set. 5 Enter a character by rotati[...]

Chapter 7 Tele-File 7-11 Chapter 7 Tele-File 7-3-5 Displa ying and Modifying Attrib ute Data You can display and modify attribute data. The example below shows attribute data displayed on the monitor. Video final recording date The most recent date (year/month/day) on which video was recorded on the tape. Title The title (name assigned to Tele-File[...]

7-12 Chapter 7 Tele-File Chapter 7 Tele-File To modify attribute data You can modify the title, ID, administrator data, and write inhibit setting attributes. However, the attributes cannot be modified when the control mode is “remote.” The modification is not possible when the write inhibit setting is ON, either. Proceed as follows after settin[...]

Chapter 8 UMID Functions Chapter 8 UMID Functions 8-1 Chapter 8 UMID Functions The UMID (Unique Material Identifier) is a type of meta-data in video and audio materials. It has been internationally standardized in SMPTE Standard 330M. This unit supports recording and generation of UMIDs. The UMID is made up of a section called the “Basic” secti[...]

Chapter 8 UMID Functions 8-2 Chapter 8 UMID Functions UMIDs can be recorded when recording video signals with this unit. You can select whether to inherit (copy) the UMID contained in input signals, or automatically or forcibly generate a new UMID. Selecting the type of UMID to record Select whether to record a Basic UMID or an Extended UMID by usi[...]

Chapter 8 UMID Functions Chapter 8 UMID Functions 8-3 3 Press the F2 (USER) button. 4 The content of the setting is a character string (in this example “ABCD”). Select any character to change in the string by pressing the F3 (PREV) and F4 (NEXT) buttons. The selected character flashes. 5 Rotate the MULTI CONTROL knob to display the desired char[...]

Chapter 8 UMID Functions 8-4 Chapter 8 UMID Functions This section explains how to output and display UMIDs. 8-3-1 UMID Output Settings You can choose to output UMIDs or not, and select either Basic UMID or Extended UMID when you choose to output UMIDs. Make these settings using setup menu item 651 UMID OUTPUT. See page 10-18 for more information a[...]

Chapter 8 UMID Functions Chapter 8 UMID Functions 8-5 Note The function for converting unit count to UTC works only when the unit rate is 2 (24 frames), 3 (24/1.001 frames), 4 (25 frames), 6 (30 frames), or 7 (30/1.001 frames). For other unit rates, the unit rate number and unit rate are displayed in hexadecimal. 5 Altitude XXXXXXXXm: Altitude data[...]

Chapter 9 Function Menu Chapter 9 Function Menu 9-1 Chapter 9 Function Menu 9-1 Overview The function menu allows you to make frequently made settings, such as selection of input video signals and time code settings. 9-1-1 Function Menu Configuration The function menu consists of six pages by factory default: the HOME page and five pages numbered 1[...]

Chapter 9 Function Menu 9-2 Chapter 9 Function Menu 9-1-2 Using the Function Menu To change a menu item setting To change a menu item setting, press the corresponding function button (F1 to F6) to display the desired setting in the lower part of the menu display. Each press of the button displays the next setting. When a menu item setting flashes M[...]

Chapter 9 Function Menu Chapter 9 Function Menu 9-3 9-2 Function Men u Item List The function menu has the following items. HOME page a) When an editing operation is carried out, CONFI playback is disabled. b) The selection of LTC or VITC depends on the setting of F6 (TCR) in function menu page 1 . c) Not displayed when F1 (TCG) is set to INT and F[...]

Chapter 9 Function Menu 9-4 Chapter 9 Function Menu Page 1 Item Setting F1 (TCG) Selects the signal source to which the internal time code generator synchronizes. INT: Synchronize according to the initial preset value set by control panel operation or by remote control from the device connected to the REMOTE1-IN (9P) connector, or synchronize to th[...]

Chapter 9 Function Menu Chapter 9 Function Menu 9-5 Page 2 Item Setting F1 (V.PROC) Selects the control method for the internal digital video processor. LOCAL: Change the settings of the internal digital video processor by using this function menu. REMOTE : Use the optional BVR-50/50P Remote Control Unit to control the internal digital video proces[...]

Chapter 9 Function Menu 9-6 Chapter 9 Function Menu Page 3 Item Setting F1 (SYNC) Sets the HD output signal sync phase. Setting method With the displayed setting flashing, you can rotate the MULTI CONTROL knob to adjust the output signal sync phase across the range ±15 µs relative to this unit’s input reference signal. Adjust this item when you[...]

Chapter 9 Function Menu Chapter 9 Function Menu 9-7 Page 4 Item Setting F1 (CAPSTN) Selects the number of fields for capstan lock in playback and editing. In 59.94i, 29.97PsF mode 2F: The capstan servo locks in units of 2 fields. • For tape output, color framing may not match the reference signal selected with the F2 (OUTREF). • In assemble edi[...]

Chapter 9 Function Menu 9-8 Chapter 9 Function Menu Page 5 9-2 Function Menu Item List Item Setting F1 (TELE-F) Displays the Tele-File menu. For details of the Tele-File menu, see Section 7-3 “Tele-File Menu” (page 7-3). F2 (UMID) Displays UMID information during recording/playback. For details of UMID, see Chapter 8.[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-1 Chapter 10 Setup Menus This unit has the following setup menus. •B asic setup menu • Extended setup menu To access the extended setup menu, a setting on the internal SS-89 board is required. For details, refer to the Installation Manual. In this manual, both the basic setup menu items and exten[...]

Chapter 10 Setup Menus 10-2 Chapter 10 Setup Menus To display setup menus With the function menu HOME page showing in the menu display, press the F5 (MENU) button. The currently selected setup menu item is displayed in the menu display, with the menu item number flashing. For basic operations in the menu display, see page 2-7. 10-2 Setup Men u Oper[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-3 To display a desired sub-item For a menu item having sub-items, you can select a desired sub-item as follows. 1 With a desired menu item selected, press the F2 (SELECT) button. The currently selected sub-item name flashes. 2 Turn the MULTI CONTROL knob to select a desired sub-item. Changing menu it[...]

Chapter 10 Setup Menus 10-4 Chapter 10 Setup Menus Resetting the menu settings to their factory default values (menu item B20) To reset the current active menu settings to their factory default values, proceed as follows. 1 Perform steps 1 to 3 of the procedure described in the section “To change the settings of menu items without sub-items” on[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-5 Line conversion mode Use the following procedure When setup menu item 018 ACTIVE LINE SELECT is set to 1035 Select the conversion mode in setup menu item 916 ACTIVE LINE 1035 CONVERT MODE. 1080 k 1035 (CONV): Convert the active scan lines from 1080 to 1035, without changing the aspect ratio. 1080 k[...]

Chapter 10 Setup Menus 10-6 Chapter 10 Setup Menus a) a) a) a) To recall settings from a menu bank When recalling the settings saved in one of menu banks 1 to 3, set the corresponding one of menu items B01 RECALL BANK 1 to B03 RECALL BANK 3 to ON, then press F5 (SET) button. When you wish to recall the settings saved in menu bank 4, select bank-4 w[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-7 10-3 Items in the Basic Setup Men u The basic setup menu contains the following items. In the “Settings” column of the table, the factory default settings are indicated by an enclosing box. Item number Item name Settings 001 PREROLL TIME 0S ... 5S ... 30S: Set the preroll time to between 0 and [...]

Chapter 10 Setup Menus 10-8 Chapter 10 Setup Menus Item number Item name Settings 009 a) CHARACTER TYPE 011 a) CHARACTER V-SIZE SYSTEM FREQUENCY SELECT Determines the type of characters such as time code output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector, HDSDI OUTPUT 3 (SUPER) connector, and SDI OUTPUT 3 (SUPER) connector for superimposed [...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-9 Item number Item name Settings B01 RECALL BANK 1 Set to ON to recall menu settings from menu bank 1. B02 RECALL BANK 2 Set to ON to recall menu settings from menu bank 2. B03 RECALL BANK 3 Set to ON to recall menu settings from menu bank 3. B11 SAVE BANK 1 Set to ON to save current active menu sett[...]

Chapter 10 Setup Menus 10-10 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu Menu items in the range 100 to 199, relating to the control panels The extended setup menu contains the following items. 10-4 Items in the Extended Setup Men u Item number Item name Settings 101 SELECTION FOR SEARCH DIAL ENABLE Select how the unit enters the s[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-11 109 Item number Item name Settings FORCED EE WHEN TAPE UNTHREAD During tape threading and unthreading, and when no cassette is inserted, select whether the setting of the function menu item PB/EE controls the PB/EE setting for output signals. OFF : Control by the function menu item PB/EE ON : No c[...]

Chapter 10 Setup Menus 10-12 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu 118 Select which switches and buttons can be operated when the KEY INHIBIT switch on the switch panel is set to ON. The following sub-items control different sets of switches and buttons independently. REMOTE SELECT Sub-item Select whether the REMOTE 1(9P) and[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-13 135 TELE-FILE THREAD COUNTER CLEAR MODE Select whether to clear the thread counter when formatting a Tele-File. NOT CLEAR : Do not clear the thread counter. WHEN FORMAT: Clear the thread counter. 136 TELE-FILE IN OUT INPUT CONTINUE Select whether to continuously input log (IN and OUT point) data i[...]

Chapter 10 Setup Menus 10-14 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu Item number Item name Settings 301 VAR SPEED RANGE FOR SYNCHRONIZATION Select the playback speed range when carrying out playback in variable speed mode from a remote control unit connected to the REMOTE-1 IN(9P) connector or REMOTE-1 OUT (9P) connector. –1~[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-15 Item number Item name Settings 310 REC INHIBIT Select the conditions under which recording is inhibited when F5 (RECINH) is set to ON in function menu page 4. ALL : All tape recording is inhibited. CRASH: Normal tape recording is inhibited. Select this setting when you wish to carry out assemble e[...]

Chapter 10 Setup Menus 10-16 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu 318 EDIT RETRY For two-VTR editing, set when this unit is used as the recorder. Selects the operation if the recorder was not synchronized in time. OFF: Editing is not carried out, and the unit stops. ON : The editing is automatically retried (up to twice). 31[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-17 Item number Item name Settings 401 FUNCTION MODE AFTER CUEUP Select the state that the unit goes into after a cuing-up operation. STOP : Stop (the “stop mode”) STILL: Still playback (in search mode) Note When controlling this unit from an editor with the standard constants set, select “STOP?[...]

Chapter 10 Setup Menus 10-18 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu Item number Item name Settings 501 STILL TIMER Select the time delay from the tape transport stopping (either the “stop mode” or the still playback mode in search mode) until the unit automatically switches to the tape protection mode, in order to protect [...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-19 602 VITC POSITION SEL-2 In 59.94i, 29.97PsF mode Select a line to insert the VITC in. (For SD output) 12H to 18H to 20H: Select any line from 12 to 20. Note You can insert the VITC signal in two places. To insert it in two places, set both items 601 and 602. In 50i, 25PsF mode Select a line to ins[...]

Chapter 10 Setup Menus 10-20 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu Item number Item name Settings 608 PHASE CORRECTION Select whether or not to carry out phase correction control on the LTC generated by the time code generator. OFF : No control ON: Carry out control. 609 TCG CF FLAG Select whether or not the color framing fla[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-21 Item number Item name Settings 620 TC CONVERT 24F t 25F (in 50i or 25PsF mode only) Select whether to convert playback time code to 25F time code during playback of tape recorded in 24PsF or 23.98PsF mode. OFF : Do not convert time code. ON: Convert time code. TC CONVERT 25F t 24F (in 24PsF or 23.[...]

Chapter 10 Setup Menus 10-22 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu 653 UMID HD VANC LINE Specify the HDSDI signal VANC line into which the UMID should be inserted. 9, 572 14,577 19,582 10,573 15,578 20,583 11,574 16,579 12,575 17,580 13,576 18,581 Note The output VANC line during playback follows the setting for recording. 65[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-23 Item number Item name Settings 703 BLANK LINE SELECT Switch blanking on or off for individual lines in the vertical blanking interval of the SD video signal. The Y/C signal and odd/even fields are blanked simultaneously. Sub-Item 0 ALL LINE - - - : Specify the blanking for each line separately. BL[...]

Chapter 10 Setup Menus 10-24 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu Item number Item name Settings 712 VIDEO PROCESS ON CAP LOCK 2FIELD When the function menu item CAPSTN or setup menu item 106 is set to 2F for 2- field playback, select whether or not to carry out a “picture shift”. OFF : No picture shift ON: Carry out pic[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-25 SYSTEM PHASE SC 719 SYSTEM PHASE SYNC Adjust the SD output signal sync phase. 0 to 80H to FFH 720 Adjust the SD output signal subcarrier phase. 0 to 3FFH 721 Y/C DELAY For playback from an analog Betacam cassette, adjust the Y/C delay. 0 to 800H to FFFH Item number Item name 715 VIDEO GAIN CONTROL[...]

Chapter 10 Setup Menus 10-26 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu Item name Settings Item number 726 H BLANKING WIDTH Select the horizontal blanking width of the video output signal. NAROW : Digital blanking (narrow) WIDE: Analog blanking (wide) When WIDE is selected, the horizontal blanking width complies with RS170A, and n[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-27 Item number Item name Settings 801 DIGITAL JOG SOUND Turns the digital jog sound on and off. OFF: Digital jog sound is turned off. Audio of digital channels not subjected to speed correction is output. When the tape stops, after one second the audio is muted. ON : Digital jog sound is turned on. W[...]

Chapter 10 Setup Menus 10-28 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu Item number Item name Settings 809 AUDIO LEVEL METER DIMMER CONTROL Set the brightness of the audio level meters. 0 to 7: Set in this range. 0 is the brightest, and 7 the dimmest. 810 AUDIO EDIT PREVIEW SWITCHER Set the output phase for the audio playback sign[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-29 826 AUDIO PB VOLUME SELECT Selects which PB control knobs are assigned to control playback of digital audio channels. Sub-item 0 ALL CH DEFAULT : Use the following settings. CH1: Control knob 1 CH2: Control knob 2 CH3: Control knob 3 CH4: Control knob 4 CH5: Unity CH6: Unity CH7: Unity CH8: Unity [...]

Chapter 10 Setup Menus 10-30 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu 903 FREEZE MODE Select the freeze mode and timing. FIELD : Freeze a video field. Field may be odd or even, according to the timing. FLD1: Freeze an odd field. FLD2: Freeze an even field. FRM1+2: Freeze a frame consisting of an odd field and following even fiel[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-31 Item number Item name Settings 934 CROSS COLOR (DC) Carry out the down-converter cross color adjustment. 0 to 8 to 15 935 DETAIL GAIN (DC) Carry out the down-converter image enhancer adjustment. Adjust the sharpness of edge emphasis. 0 to 20H to 7FH 936 LIMITER (DC) Carry out the down-converter im[...]

Chapter 10 Setup Menus 10-32 Chapter 10 Setup Menus 10-4 Items in the Extended Setup Menu Item number Item name Settings 942 V FILTER SELECT Set the vertical interpolation filter coefficient for HD-SD converter output. The vertical resolution increases as the setting grows larger. 1 to 3 943 CROSS COLOR CRISP Set the cross color crisp level for HD-[...]

Chapter 10 Setup Menus Chapter 10 Setup Menus 10-33 961 BACKGROUND COLOR (UC) Set the color of the part where no material exists (background) for up-converting. BACK GROUND COLOR: Set the color. BLACK : Black GRAY: Gray BLUE: Blue TABLE: Set with the following Y/PB/PR tables. Y TABLE: Adjust the background Y level. 0 to FFH B-Y TABLE: Adjust the ba[...]

Chapter 11 Maintenance and Inspection 11-1 Chapter 11 Maintenance and Inspection 11-1 Remo ving a Cassette When T ape Slac k Occur s If tape slack occurs in the unit, it is necessary to remove the upper lid and sound baffle. This job should always be entrusted to a technician who has undergone service training. To clean the video heads and audio he[...]

11-2 Chapter 11 Maintenance and Inspection Chapter 11 Maintenance and Inspection 11-3 Err or Messages Z ALARM indicator This unit is equipped with a self-diagnosis function, and if a problem is detected, displays an error message in the time data display and on the monitor. If an error message appears, contact your Sony service representative. Indi[...]

Chapter 11 Maintenance and Inspection 11-3 Chapter 11 Maintenance and Inspection Error Message List Code Message Description – NO COMMUNICATION Abnormality in the interface between the lower control panel (KY-464/465 board) and SYS CPU (SS-89 board) has been detected on the lower control panel side. 01 REEL TROUBLE Tape slacking has been detected[...]

11-4 Chapter 11 Maintenance and Inspection Chapter 11 Maintenance and Inspection 11-4 Moisture Condensation When the unit is suddenly moved from a cold to a warm location, or used in a very humid place, moisture from the air can condense on the head-drum. This is called moisture condensation. If the tape is run in this state, it can adhere to the d[...]

Chapter 11 Maintenance and Inspection 11-5 Chapter 11 Maintenance and Inspection 11-5 Regular Chec ks 11-5-1 Digital Hours Meter The digital hours meter can display seven items of information, in corresponding display modes, about the operational history of the unit. Use it as a guide in scheduling periodic maintenance. Display modes of the hours m[...]

11-6 Chapter 11 Maintenance and Inspection Chapter 11 Maintenance and Inspection Component Digital hours meter indication (menu number in parenthesis) Guideline replacement intervals R: Replace C: Check, and replace if necessary 1000 hrs 2000 hrs 3000 hrs 4000 hrs 5000 hrs 6000 hrs Upper drum Drum running time (H02) Drum assembly Brush slip ring as[...]

Appendix Appendix A-1 Specifications General Recording format HDCAM Power requirements 100 to 240 VAC, 50/60 Hz Power consumption 2.2 A (220 W), when used without optional devices Peak inrush current (1) Power ON, current probe method: HDW-2000 40 A (240 V), 20 A (100 V) HDW-M2000/M2000P 50 A (240 V), 14 A (100 V) (2) Hot switching inrush current, [...]

Appendix A-2 Appendix Specifications Digital Betacam playback: Still to approx. ±50 times normal playback speed MPEG IMX/Betacam SX playback: Still to approx. ±78 times normal playback speed Analog Betacam playback: Still to ±35 times normal playback speed (525/59.94) Still to ±42 times normal playback speed (625/50) Variable speed mode HDCAM p[...]

Appendix Appendix A-3 Digital Betacam playback Video Digital Audio (CH1 to CH4) Analog Audio (cue track) MPEG IMX playback Video Digital Audio (CH1 to CH4) Betacam SX playback Video Digital Audio (CH1 to CH4) Bandwidth Y0 to 5.75 MHz +0.5 dB/–0.5 dB K factor R–Y/B–Y 0 to 2.75 MHz +0.5 dB/–0.5dB S/N ratio 62 dB or more 1 % or less Frequency [...]

Appendix A-4 Appendix Specifications Analog Betacam playback Video Audio a) Reference level: +4 dBm Processor adjustment range Video level ±3 dB/ – ∞ to +3 dB selectable Chroma level ±3 dB/ – ∞ to +3 dB selectable Setup level (59.94i, 29.97PsF mode) ±30 IRE Black level (50i, 25PsF mode) ±210 mV Chroma phase ±30° System phase Sync: ±1[...]

Appendix Appendix A-5 AUDIO INPUT(AES/EBU) CH1/2, 3/4 BNC (2) Complies with AES-3id-1995 TIME CODE IN XLR 3-pin, female (1) 0.5 to 18 Vp-p, 10 k Ω , balanced Output connectors HDSDI OUTPUT BNC (3 including 1 for character superimposition) Serial digital (1.485 Gbits/s) SMPTE 292M SDTI OUTPUT BNC (2) (optional) SMPTE 305M (SDTI) COMPONENT VIDEO OU[...]

Appendix A-6 Appendix Specifications Optional accessories HKDW-101 Control Panel HKDW-102 SDTI Interface Board BKMW-102 Remote Control Unit BKMW-103 Control Panel Extension Kit RCC-5G 9-pin remote control cable (1) BVR-50/50P Video Remote Control Unit HKDV-900 Video Remote Control Unit RMM-131 Rack Mount Adaptor BCT-HD12CL Cleaning Cassette Tape AC[...]

Appendix Appendix A-7 Relation between HKDV-900/503 setting items and setup menu of this unit a) Valid for output only when F1 (V.PROC) in function menu page 2 is set to MENU. b) Select whether to set DC or UC with menu item 212 (VIDEO REMOTE CONTROL SELECT). When both are selected (menu item 212 is U&D), both of the corresponding menu settings[...]

Appendix A-8 Appendix Specifications HD/SD video output phase settings For the HD/SD video output phase setting, you can use the maintenance menu. For details, refer to the Installation Manual. Item number Item name Settings M3 M3A: OUTPUT PHASE SELECT M3A0: HD PHASE SEL Select the HD video output signal phase with respect to the reference signal: [...]

Index Index I-1 Index A AC IN connector 2-17 ALARM indicator 2-12 Analog audio input/output section 2-15 video input/output section 2-16 ASSEMBLE button 2-11 Audio control section 2-4 monitor signal output section 2-18 monitor signal selection buttons 2-5 selection function selector buttons 2-4 setting display section 2-4 AUDIO IN/OUT buttons 2-13 [...]

Index Index I-2 Index N Non-drop frame mark 3-7 mode 9-4 O Operation mode 3-7 OUTREF (function menu) 9-7 P PANEL SELECT switch 2-14 Parts replacement 11-6 PB controls 2-6 PB/EE (function menu) 9-3 PHONES jack/control 2-2 PLAY button 2-11 Playback capstan override 4-8 dynamic motion control (DMC) 4-10 jog mode 4-7 normal 4-6 shuttle mode 4-7 speed i[...]

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenan[...]

 2001 HDW-2000/M2000/M2000P (SYL, ) 3-205-317- 14 (1) Son y Cor poration B & P Company[...]