Français dropdown-ico

Sony PCS-1 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Sony PCS-1. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Sony PCS-1 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Sony PCS-1 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Sony PCS-1 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Sony PCS-1
- nom du fabricant et année de fabrication Sony PCS-1
- instructions d'utilisation, de réglage et d’entretien de l'équipement Sony PCS-1
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Sony PCS-1 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Sony PCS-1 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Sony en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Sony PCS-1, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Sony PCS-1, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Sony PCS-1. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    COMMUNICATION SYSTEM PCS-1 PCS-1P SYSTEM INTEGRA TION MANUAL 1st Edition[...]

  • Page 2

    PCS-1/PCS-1P ! W ARNING This manual is intended for qualified service personnel only . T o reduce the risk of electric shock, fire or injury , do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! W ARNUNG Die Anleitung ist nur f?[...]

  • Page 3

    1 PCS-1/PCS-1P Table of Contents 1. Installation 1-1. Caution on Installation ................................................................................ 1-1 1-1-1. Lay Out the Videoconferencing Room ...................................... 1-1 1-1-2. Operating Environment .............................................................. 1-6 1-2. F[...]

  • Page 4

    2 PCS-1/PCS-1P 4. Technical Data 4-1. PCS-1/1P Port Number Used ...................................................................... 4-1 4-1-1. During Opposed Connection (Specified Value) ........................ 4-1 4-1-2. Opposed Connection (User Setting: When TCP port number is set to 3000 and UDP port number is set to 3100) ..................[...]

  • Page 5

    1-1 PCS-1/PCS-1P Section 1 Installation 1-1. Caution on Installation 1-1-1. Lay Out the Videoconferencing Room Arrange it in consideration of the space of a camera and microphone when laying out the videoconferencing room. Camera Range represents the shooting area of the camera when the zoom has been extended fully. indicates the shooting area of t[...]

  • Page 6

    1-2 PCS-1/PCS-1P 1: For internal microphone 2: For extension microphone (PCS-A300) 0.5 1 3: For extension microphone (PCS-A1) 0.5 to 1.2m Highly directional range of microphone The ideal directional range of a microphone is shown below. The numeric value is a rough standard. Use the value as the reference of the videoconferencing room used.[...]

  • Page 7

    1-3 PCS-1/PCS-1P The microphone built in the PCS-C1/C1P Camera Unit is assumed to be used to conduct a conference among about three participants. You can connect the optional PCS-A1 or PCS-A300 microphone to the System, allowing more persons to participate in the conference. Microphone layout examples PCS-1/1P Microphone built in the PCS-1/1P PCS-A[...]

  • Page 8

    1-4 PCS-1/PCS-1P The blue line in the light emitter indicates the direction of infrared rays. Infrared light emitter : Adjustment in vertical direction : Adjustment in horizontal direction Document stand Infrared rays Infrared photosensor PCS-1/1P Installation of document stand a. Adjust the direction of an infrared light emitter. Install so that t[...]

  • Page 9

    1-5 PCS-1/PCS-1P 45 d 30 d Infrared light emitter Infrared light emitter Infrared light emitter 5 m 15 d 3.5 m 2.5 m Infrared photosensor PCS-1/1P b. Installation range (Reference) If an image is disturbed in the range shown below, bring it near PCS-1/1P with the infrared light emitter of a documents stand turned toward PCS-1/1P. m . Install so tha[...]

  • Page 10

    1-6 PCS-1/PCS-1P 1-1-2. Operating Environment Layout Considerations . Avoid having large, moving objects, especially people, behind the participants, as the quality of the picture transmitted to the remote party will deteriorate. . Do not seat participants in front of a wall with fine stripe patterns. . Choose a room where echo will not occur. . Do[...]

  • Page 11

    1-7 PCS-1/PCS-1P Place used Unpacking Check of supplied accessories Power and cable connection, and preparation Start the power of the system and initialize. <Refer to “1-1. Caution on Installation” on page 1-1.> <Refer to “1-3. System Connections” on page 1-8.> <Refer to “1-4. Initialization” on page 1-10.> Initialize[...]

  • Page 12

    1-8 PCS-1/PCS-1P 1-3. System Connections This section describes the typical system connections. m . Be sure to turn off all the equipment before making any connections. . Do not connect/disconnect the camera cable with the power on. Doing so may damage the Camera Unit or Communication Terminal. . For safety, do not connect the 100BASE-TX/10BASE-T c[...]

  • Page 13

    1-9 PCS-1/PCS-1P 1-3-2. When Used in ISDN n Do not connect/disconnect the camera cable or the interface cable with the power on. Doing so may damage the Camera Unit, Communication Terminal or ISDN Unit. 12 3 4 5 6 DC 19.5V AUDIO OUT AUDIO IN AUX1 – VIDEO IN – AUX2 CAMERA UNIT MIC (PLUG IN POWER) ISDN UNIT WHITE BOARD (MIXED) AUX MAIN – MONITO[...]

  • Page 14

    1-10 PCS-1/PCS-1P 1-4. Initialization 1-4-1. Inserting Batteries into the Remote Commander Most of the operations with the Video Communication System can be controlled with the supplied Remote Commander. 1. Remove the battery compartment cover. 2. Insert two size AA (R6) batteries (supplied) with correct polarities into the battery compartment. n B[...]

  • Page 15

    1-11 PCS-1/PCS-1P 1-4-2. Turning On/Off the TV Monitor Together With the Communication Terminal If you use a Sony TV, insert the IR repeater under the remote sensor of the TV. Once you set the IR repeater, the TV will turn on or go to standby together with the Communication Terminal when you press the I/O button on the supplied Remote Commander. n [...]

  • Page 16

    1-12 PCS-1/PCS-1P 1-4-3. Adjust the Volume of a Monitor Television Adjust the television side after the volume is adjusted on the PCS-1/1P side. 1. Press the volume/bright button of a remote controller and adjust so that the volume adjustment bar is in the center position 2. Adjust the volume of a monitor television. Set to the volume in which the [...]

  • Page 17

    1-13 PCS-1/PCS-1P 1-4-5. Turning On 1. Turn on the TV monitor. If the IR repeater is installed in the TV monitor, set the TV monitor to standby mode. The TV monitor will turn on simultaneously when the Communication Terminal is turned on. 2. Turn on the power of any other equipment to be used for the videoconference. 3. Set the power switch on the [...]

  • Page 18

    1-14 PCS-1/PCS-1P Language Setup Wizard Cancel Next English Language 1-4-6. When the Power was First Turned on after Installation When you turn on the Communication Terminal for the first time after installation and the self-diagnosis is completed, the setup wizard appears on the monitor screen. Register your local system data with the setup wizard[...]

  • Page 19

    1-15 PCS-1/PCS-1P Area Code Local Number Cancel Next Previous A2 A1 B1 B2 C1 C2 5. Enter the telephone number of the ISDN used by the system. When you use one ISDN line, enter the same number both in the A1 and A2 text boxes (except for the USA and Canada). Area Code: Enter the area code. Do not enter the first “ 0 ” number. Local Number: Enter[...]

  • Page 20

    1-16 PCS-1/PCS-1P LAN Setup Wizard Cancel Next Previous Auto DHCP Mode Host Name IP Address Network Mask Gateway Address DNS Address . . . . . . . . . . . . 9. Set the following items on the LAN. DHCP Mode: Sets the DHCP (Dynamic Host Configuration Protocol). Auto: Automatically assigns your IP address, network mask, gateway address and DNS address[...]

  • Page 21

    1-17 PCS-1/PCS-1P 1-5. System Setting The contents of a setting menu are shown in the table below. Change the setting as required. Contents of setting Select the line interface (LAN, ISDN, or voice telephone) used. Select “ On ” when connecting using a bonding interface through which the remaining lines can also be connected by only dialing one[...]

  • Page 22

    1-18 PCS-1/PCS-1P Contents of setting Select the language (English, French, German, Japanese, Spanish, Italian, or Chinese) of the menu and message displayed on the screen. Select the mode for putting the monitor into the standby state or turning on the power when a Sony ’ s monitor is used. Usually, set to “ Mode 1 ” . Set to “ on ” when[...]

  • Page 23

    1-19 PCS-1/PCS-1P Contents of setting Set the user number (E.164 number) registered in a gate keeper. Set to “ On ” when enabling the service of an SNMP (Simple Network Management Protocol) agent. Set to “ Off ” when disabling it. Set the IP address of an SNMP manager that transmits a trap. Set the community name that an SNMP manager manage[...]

  • Page 24

    1-20 PCS-1/PCS-1P 1-6. Flowchart of Opening Test Opening test Communicate using ISDN? ISDN outgoing ISDN incoming LAN outgoing LAN incoming <Refer to “ 1-6-1. Outgoing Procedure of ISDN ” on page 1-21.> <Refer to “ 1-6-2. Incoming Procedure of ISDN ” on page 1-23.> <Refer to “ 1-6-3. Outgoing Procedure of LAN ” on page 1-[...]

  • Page 25

    1-21 PCS-1/PCS-1P 1-6-1. Outgoing Procedure of ISDN n It is required that the line number used in the other end is entered in the area code and local number of the ISDN setting menu of the other end. Item 1. 2. 3. 4. 5. Operation Select “ Dial ” from the launcher menu using ↑ , ↓ , ← , and → buttons of a remote controller and press the [...]

  • Page 26

    1-22 PCS-1/PCS-1P Item 6. 7. Operation The remote side makes a response. Disconnection Press the connect/disconnect ( / ) button of a remote controller. A confirmation message on whether to disconnect a line is then displayed. Select “ OK ” using a ← or → button of a remote controller and press the decide button, or press the connect/discon[...]

  • Page 27

    1-23 PCS-1/PCS-1P 1-6-2. Incoming Procedure of ISDN n It is required that the line number used in this unit is entered in the area code and local number of the ISDN setting menu before receiving a signal from the other end. Item 1. 2. 3. Operation Incoming from the remote side <For automatic response> <For manual response> Remote discon[...]

  • Page 28

    1-24 PCS-1/PCS-1P Item 1. 2. 3. 4. 5. Operation Select “ Dial ” from the launcher menu using ↑ , ↓ , ← , and → buttons of a remote controller and press the decide button, or press the connect/disconnect ( / ) button of a remote controller. Select “ Line type ” using ↑ , ↓ , ← , and → buttons of a remote controller and press [...]

  • Page 29

    1-25 PCS-1/PCS-1P Item 6. 7. Operation The remote side makes a response. Disconnection Press the connect/disconnect ( / ) button of a remote controller. A confirmation message on whether to disconnect a line is then displayed. Select “ OK ” using a ← or → button of a remote controller and press the decide button, or press the connect/discon[...]

  • Page 30

    1-26 PCS-1/PCS-1P Item 1. 2. 3. Operation Incoming from the remote side <For automatic response> <For manual response> Remote disconnection Screen Remarks (Confirmation item) An incoming sound occurs. “ Incoming ” is displayed on the screen. During connection, “ Start meeting ” is displayed, and the remote voice and image are he[...]

  • Page 31

    2-1 PCS-1/PCS-1P Section 2 Maintenance Connect Phone Book Dial Menu Show Help Angle Adj. More Options IP LAN Line I/F Dial A2 B1 B2 C1 C2 1024 Kbps LAN Bandwidth Dial Save 2-1. Confirmation Procedure of Local Terminal Operation Using Self-Loop A self-loop is the reflected loop in ISDN unit PCS-B768. It does not operate when ISDN unit PCS-B768 is no[...]

  • Page 32

    2-2 PCS-1/PCS-1P 2-2. Separation of Components The main troubles that occur during failure are described in the table below. Trouble 1. The power is not turned on even if the power switch on the side panel is pressed. SS-01 2. The power is not turned on even if the power button of a remote controller is pressed. SS-02 3. The power is not turned on [...]

  • Page 33

    2-3 PCS-1/PCS-1P Is power cord properly connected? Does POWER (green) lamp light? YES NO NO Proceed to “5. The power of a monitor television is not turned on during the power-on sequence”. Connect it properly . YES SS-01 Communication terminal or AC adaptor is defective. 1. The power is not turned on even if the power switch on the side panel i[...]

  • Page 34

    2-4 PCS-1/PCS-1P YES NO NO Proceed to “ 1. The power is not turned on even if the power switch on the side panel is pressed ” . Remote controller ’ s battery is exhausted or remote controller is defective. YES NO YES Is initial screen displayed during start when power is turned on again using power switch on side panel? Can light emitting be [...]

  • Page 35

    2-5 PCS-1/PCS-1P YES NO NO T urn on power switch on side panel. Connect them properly . YES NO YES Is power turned on when I/O button of remote controller is pressed? Are communication terminal and ISDN unit properly connected? Does POWER (amber) lamp light? SS-03 Communication terminal is defective. Proceed to “ 2. The power is not turned on eve[...]

  • Page 36

    2-6 PCS-1/PCS-1P YES YES NO V erify whole system including network administrator . T urn on power switch on side panel. Communication terminal is defective. YES NO YES Does POWER (amber) lamp light? Is LAN cable properly connected to 100BASE- TX/10BASE-T terminal? Is power turned on when I/O button of remote controller is pressed? Is other companie[...]

  • Page 37

    2-7 PCS-1/PCS-1P YES YES NO NO NO T urn on the main power switch of monitor TV . Connect and locate the IR repeater correctly . Set it properlycorrectly . YES NO YES Are the connection and location of IR repeater correct? Does the setting of “ IR repeater mode ” on page 3 of the general setting menu correspond to the monitor? Is the main power [...]

  • Page 38

    2-8 PCS-1/PCS-1P 6. The image from a camera is not displayed after the power is turned on. YES YES YES YES Set the video signal input to “ main ” . NO NO NO NO YES Is the launcher menu displayed? Is the video signal input set to “ main ” ? Does POWER (green) lamp of camera unit light? When the video signal is input to the VIDEO IN AUX1 term[...]

  • Page 39

    2-9 PCS-1/PCS-1P YES YES YES Remote controller is defective. Communication terminal is defective. NO NO Can menu be operated using ↑ , ↓ , ← , and → buttons and decide button? Can zoom button or volume button be operated? Could power be turned on using I/O button of remote controller? SS-07 NO Remote controller is defective. Proceed to “ [...]

  • Page 40

    2-10 PCS-1/PCS-1P 8. The camera on the local side cannot be operated. YES YES Connect it properly . NO NO Does POWER (green) lamp of camera unit light? Is camera unit properly connected to communication terminal? SS-08 Camera unit is defective. Communication terminal is defective.[...]

  • Page 41

    2-11 PCS-1/PCS-1P YES NO Communication terminal is defective. Set it properly . YES Are contents of setting in dial list and system setup proper? (For bonding connection, check that address of ISDN line connected to local terminal is properly set to second page of ISDN set menu on the incoming side.) Do ST A TUS 1 to 6 lamps of ISDN unit light in y[...]

  • Page 42

    2-12 PCS-1/PCS-1P Are the setting contents of the dial list and system setup correct? NO YES Are the connection of LAN cable, and the setting of IP address and net mask correct? NO YES Set it properly . SS-10 Connect and set correctly . Communication terminal is defective. 10. No line is connected. (LAN)[...]

  • Page 43

    2-13 PCS-1/PCS-1P 11. No voice can be heard from the remote side after a line is connected. YES NO NO YES T urn up the volume of the monitor TV . Ask the other end of the line to turn on the microphone. NO YES NO YES Is the volume of the main unit turned down? Is the microphone of the other end of the line turned on? Is the connection of the voice [...]

  • Page 44

    2-14 PCS-1/PCS-1P 12. No voice can be transmitted to the remote side after a line is connected. Is AUX set to “ Input switching ” of audio set menu? YES YES NO Is microphone OFF canceled? Is Internal set in “ Microphone selection ” of audio set menu? NO NO YES Is DSB AUX IN set in “ Microphone selection ” of audio set menu? Is audio sig[...]

  • Page 45

    2-15 PCS-1/PCS-1P Is video input properly set? Is “ Object ” selected as video input? NO YES YES NO Press input selector button of remote controller and select input properly using joystick. SS-13 Is video signal output from equipment connected to AUX1 and AUX2 terminals? YES Connected equipment is defective. NO Communication terminal is defect[...]

  • Page 46

    2-16 PCS-1/PCS-1P 14. An image on the remote side is not displayed after a line is connected. Is the video signal output connected from VIDEO OUT MONIT OR MAIN or VIDEO OUT AUX? NO YES Is the image of the other end displayed when a connection is made with another communication end? NO YES Connect correctly . SS-14 Check the terminal of the other en[...]

  • Page 47

    2-17 PCS-1/PCS-1P 15. An image cannot be transmitted to the remote side after a line is connected. Is the setting of the video signal input correct? NO YES Can the video signal be sent to the other end when a connection is made with another communication end? NO YES SS-15 Check the terminal of the other end. Communication terminal is defective. Is [...]

  • Page 48

    2-18 PCS-1/PCS-1P (RS-232C cross cable) PCS-1/1P Personal computer ON LINE POWER LAN ALERT 2-3. Operation Log PCS1/1P has a function that outputs the internal processing history, between the connection and disconnection of a line, to the commercial PC connected to the outside and a function that saves the latest history of 1M byte in a memory stick[...]

  • Page 49

    2-19 PCS-1/PCS-1P (1) Click “ Start menu ” , “ Accessory ” , “ Communication ” , and then “ Hyper terminal ” . (2) Enter “ VT100 ” in “ Name (N) ” , select any icon, and click the “ OK ” button.[...]

  • Page 50

    2-20 PCS-1/PCS-1P (3) Select “ COM1 ” in “ Connect To ” and click the “ OK ” button. (4) Set the baud rate as described below and click the “ OK ” button. Bit/s: 38,400 Data bit: 8 Parity: None Stop bit: 2 Flow control: Xon/Xoff[...]

  • Page 51

    2-21 PCS-1/PCS-1P (5) Click “ Capture Text ” from a “ Transfer ” menu. (6) Set the saving place and name of a log file and click “ Start ” .[...]

  • Page 52

    2-22 PCS-1/PCS-1P (7) After logging, click “ Stop ” from “ Capture Text ” in a “ Transfer ” menu. (8) Double-click the extracted log file to view a log.[...]

  • Page 53

    2-23 PCS-1/PCS-1P Operation log using commercial PC (2) When PCS-1/1P is connected to LAN, a log can be extracted from PCS-1/1P using telnet with PC connected to LAN. Even when PCS-1/1P is not connected to LAN, a log can be extracted from PCS-1/1P using telnet by connecting the 100BASE-TX/10BASE-T terminal on the rear panel of PCS-1/1P and the LAN [...]

  • Page 54

    2-24 PCS-1/PCS-1P (2) Enter ping, and then enter the IP address of PCS-1/1P after spacing out. Press the [Enter] key and confirm that a reply is returned. After confirmation, close the command prompt. (3) Click “ Start menu ” , “ Accessory ” , “ Communication ” , and then “ Hyper terminal ” .[...]

  • Page 55

    2-25 PCS-1/PCS-1P (4) Enter “ LAN ” in “ Name: ” , select any icon, and click the “ OK ” button. (5) Select “ TCP/IP (Winsock) ” in “ Connect To ” , enter the IP address of PCS-1/1P in “ Host address: ” , and click the “ OK ” button.[...]

  • Page 56

    2-26 PCS-1/PCS-1P (6) Click “ Capture Text ” from a “ Transfer ” menu. (7) Set the saving place and name of a log file and click the “ Start ” button. Example of name: PCS-1LOG.txt[...]

  • Page 57

    2-27 PCS-1/PCS-1P (8) The message below is displayed on the hyper terminal screen. PCS-1 Telnet Server login: Enter sonypcs and press the Enter key. Password: is then displayed. Press the Enter key again. A log begins to be extracted. (9) After log extraction is completed, click “ Stop ” from “ Capture Text ” in a “ Transfer ” menu. (10[...]

  • Page 58

    2-28 PCS-1/PCS-1P POWER lamp (green) Memory Stick slot 2-4. Updating of Software The software of the main unit may be updated for improvement in a function. Two methods are available for updating. 2-4-1. Updating Using Memory Stick Turn off the power switch on the side panel of the main unit. Turn on the power switch. The POWER lamp (green) lights.[...]

  • Page 59

    2-29 PCS-1/PCS-1P Dial Multipoint General ISDN Information Answer Audio Administrator LAN Status Setup Dial Multipoint General ISDN Information Answer Audio Administrator LAN Status Setup 2-5. Service Mode In the service menu of PCS-1/1P, data can be saved in the Memory Stick of an address book using a commercial Memory Stick or read from a Memory [...]

  • Page 60

    2-30 PCS-1/PCS-1P For loading of application 1. Display a service menu. 2. Insert the Memory Stick, in which the application software of the version to be loaded is recorded, into a Memory Stick slot. 3. Select “ Load application ” using ↑ , ↓ , ← , and → buttons of a remote controller and press the decide button. 4. A confirmation mess[...]

  • Page 61

    2-31 PCS-1/PCS-1P 9) Loading of setting The set information ( ¥ MSSONY ¥ PRO ¥ TVCONF ¥ SETUP ¥ PCS_STUP.CSV) recorded in a Memory Stick is overwritten in the set menu of the main unit. After execution, the screen disappears once, and a launcher menu is displayed in the same way as after the power is turned on. The set information cannot be re[...]

  • Page 62

    [...]

  • Page 63

    3-1 PCS-1/PCS-1P Section 3 Compatibility in LAN Network LAN1 Teleconference terminal A 192.100.10.10 Teleconference terminal B 192.100.10.20 HUB LAN2 3-1. Connection via Hub Example of system When a call is initiated from teleconference terminal A to teleconference terminal B. 1. The LAN set menu of teleconference terminal B is set as described bel[...]

  • Page 64

    3-2 PCS-1/PCS-1P 3. The LAN set menu of teleconference terminal A is set as described below. DHCP mode: OFF Host name: Enter any name. IP address: Local IP address (192.100.10.10) Network mask: Depends on a network. Usually, set to 255.255.255.0. Gateway address: Blank DNS address: Blank Gatekeeper used: OFF Gatekeeper address: Blank User name: Bla[...]

  • Page 65

    3-3 PCS-1/PCS-1P 192.100.10.1 WAN 192.100.20.1 Teleconference terminal A 192.100.10.10 Teleconference terminal B 192.100.20.20 Router Router LAN1 LAN2 3-2. Connection via Router Example of system When a call is initiated from teleconference terminal A to teleconference terminal B. 1. The LAN set menu of teleconference terminal B is set as described[...]

  • Page 66

    3-4 PCS-1/PCS-1P 3. The LAN set menu of teleconference terminal A is set as described below. DHCP mode: OFF Host name: Enter any name. IP address: Local IP address (192.100.10.10) Network mask: Depends on a network. Usually, set to 255.255.255.0. Gateway address: 192.100.10.1 DNS address: Blank Gatekeeper used: OFF Gatekeeper address: Blank User na[...]

  • Page 67

    3-5 PCS-1/PCS-1P Teleconference terminal A Teleconference terminal B DHCP server A DHCP server B Router Router LAN1 LAN2 3-3. Connection via DHCP Example of system When a call is initiated from teleconference terminal A to teleconference terminal B. 1. The LAN set menu of teleconference terminal B is set as described below. DHCP mode: ON Host name:[...]

  • Page 68

    3-6 PCS-1/PCS-1P 3. The LAN set menu of teleconference terminal A is set as described below. DHCP mode: ON Host name: Enter any name. IP address: Blank Network mask: Blank Gateway address: Blank DNS address: Blank Gatekeeper used: OFF Gatekeeper address: Blank User name: Blank User number: Blank SNMP service: OFF Trap transmission destination: Blan[...]

  • Page 69

    3-7 PCS-1/PCS-1P 192.100.10.1 192.100.20.1 Teleconference terminal A 192.100.10.10 User name: PCS1A User number: 100 Teleconference terminal B 192.100.20.20 User name: PCS1B User number: 200 Gatekeeper 192.100.10.20 Router Router LAN1 LAN2 3-4. Connection via Gatekeeper Example of system When a call is initiated from teleconference terminal A to te[...]

  • Page 70

    3-8 PCS-1/PCS-1P 4. The LAN set menu of teleconference terminal A is set as described below. DHCP mode: OFF Host name: Enter any name. IP address: Local IP address (192.100.10.10) Network mask: Depends on a network. Usually, set to 255.255.255.0. Gateway address: 192.100.10.1 DNS address: Blank Gatekeeper used: ON Gatekeeper address: 192.100.10.20 [...]

  • Page 71

    3-9 PCS-1/PCS-1P Teleconference terminal A User name: PCS1A User number: 100 Teleconference terminal B User name: PCS1B User number: 200 DHCP server A DHCP server B Gatekeeper 192.100.10.20 LAN1 LAN2 Router Router 3-5. Connection via DHCP and Gatekeeper Example of system When a call is initiated from teleconference terminal A to teleconference term[...]

  • Page 72

    3-10 PCS-1/PCS-1P 4. The LAN set menu of teleconference terminal A is set as described below. DHCP mode: ON Host name: Enter any name. IP address: Blank Network mask: Blank. Gateway address: Blank DNS address: Blank Gatekeeper used: ON Gatekeeper address: 192.100.10.20 User name: Enter any name. (Example: PCS1A) User number: Enter any number. (Exam[...]

  • Page 73

    4-1 PCS-1/PCS-1P Section 4 Technical Data 4-1. PCS-1/1P Port Number Used 4-1-1. During Opposed Connection (Specified Value) PCS-1 uses the port number below during opposed connection when the port number used in a LAN set menu is set as “Specified value”. Port number RAS (PCS-1/1P) 2253 (when GK is used) RAS (Gatekeeper) 1719 (when GK is used) [...]

  • Page 74

    4-2 PCS-1/PCS-1P 4-1-3. During Use of Internal MCU Function (Specified Value) PCS-1/1P that operates as internal MCU uses the port number below when the port number used in a LAN set menu is set as “ Specified value ” . The port number that a sub-terminal uses is the same as during opposed connection. Port number (at first point) Port number (a[...]

  • Page 75

    4-3 PCS-1/PCS-1P 4-2. Setting of PCS-1 and HUB The initial setting of the PCS-1 is Auto. In the Auto setting of the PCS-1, 10/100 can be selected automatically, however, Half/Full cannot be selected automatically. Therefore, if the HUB is set to Full mode, a connection failure or packet loss occurs. The following table shows an example of connectio[...]

  • Page 76

    [...]

  • Page 77

    [...]

  • Page 78

    Sony Corporation 2003. 7 22 B&P Company ©2003 PCS-1 (UC) PCS-1P (CE) E 9-968-036-01[...]