Telex BTR-500/600C manuel d'utilisation

T elex Operating Instructions RadioCom ™ BTR-500/600C TR-500/600C Professional W ireless Intercom Set R T ALK A 1B 2 RadioCom TM ON OFF B E L T P A C K IN OUT I/C IN OUT AUX LOCAL BEL T P ACK SIDETONE AUDIO CHANNEL BTR-600C 1 2 I/C TELEX OUT IN 1 2 RTS AUTO AUX OFF ON CODE SWITCH VOL MIC GAIN T ALK/ OM HEADSET T ele x[...]

T able of Contents Introduction ............................................................................................................................... ...........1 General Description ............................................................................................................. ............1 System Features .................[...]

T able of Contents (Continued) System Operation ...............................................................................................................................21 Base Station Operation ........................................................................................................... .......21 Power .........................[...]

Intr oduction General Description The T elex Radiocom BTR-500 and BTR-600C UHF W ireless intercom systems offer the ultimate in reliable, high performance, high fidelity full du- plex communications. The BTR-500 series includes the BTR-500 fre - quency agile base station, working with the TR-500 transceiver beltpack. The BTR-500 base station pro- v[...]

Base Station T ransceiver Contr ols and Connections 1. Power Switch - Illuminates when on. 2. Beltpack Light - Illuminates when a beltpack is transmit- ting to base station. 3. Intercom In Level Contr o l - Adjust for optimum level. Intercom light #1 1 should just flash red on loudest speech. 4. Intercom Out Level Contr o l - Adjusts output to matc[...]

Base Station Contr ols and Connections - Rear Panel 1. T ransmit Antenna Jack - Color band on antenna must match color dot on base station. Female “TNC” Connec- tor . 2. T ransmit Channel Switch - Changes frequency of beltpack (shown on Serial No. T ag). Must match receive channel on beltpack. 3. Audio Out - “RCA” type jack provides a high [...]

9. & 10. Loop Thru I/C - 9 pin D-sub jack. W ired as shown. 1 1. See #8. 12. Auxiliary Jack - 6 pin RJ-1 1 telephone type jack. Com - patible with “R TS Matrix” type intercoms. Figure 6 Auxiliary Jack 13. Power Jack - 12-15 VDC, 400mA minimum or 12-15 V AC rms, 400mA rms minimum. Accepts 5.5 mm x 2.1 mm plug. 14. Receive Channel Switch - Ch[...]

Beltpack Contr ols and Connections 1. V olume Control and Power Switch - T urns power on and off and controls headset volume. 2. Battery/Overmodulation Light - Flashes once when unit is turned on if battery is good. If light stays on, battery is low . If light does not flash, battery is dead. Flickering red light when talking means microphone gain [...]

-6- Beltpack Specifications RF Output .............................................................2 5 m W typical T emperature Range ......................................... -4°F to 130°F (-20°C to 55°C) Dimensions ............................4 " Wx5 7/8"H x 1 5/8"D (120mm x 149mm x 41mm) W eight ...............................[...]

Initial Equipment Set-Up Unpacking Unpack your RadioCom System. A system package should contain the following Items: Contact the shipper or your dealer immediately if anything is damaged or missing. Fill out the regis- tration card and return it to T elex to properly regis- ter your unit. Antenna Information Antenna Connection The base station is s[...]

Attach the transmit 1/2-wave antenna to the antenna input receptacle labeled “T ransmit” on the left side of the rear panel. The antenna should be vertically aligned. Figure 10 Attaching T ransmit 1/2-W ave Antenna Antenna Polarization The T elex W ireless Intercom System is “V ertically Polarized”. This means both the transmitting and re- [...]

Keep the distance between the BTR and the TR as short as possible. The greater the distance, the weaker the signal. Make sure the “signal paths” be- tween the BTR and TR are unobstructed. Y ou should be able to visibly locate the antennas at all times for best performance. Figure 13 Distance Between base station and beltpack Figure 14 Keeping S[...]

Figure 16 Antenna Placement Improving Reception and Incr easing Range Keeping the distance from the base station and beltpack as short, and unobstructed as possible will produce the most reliable performance. The base station is supplied with two antennas. This should provide satisfactory system performance in most applications. System range can be[...]

Base Station Set-Up Location Locate the base station on a level surface with the rear of the unit facing you. See “Antenna Informa- tion” section for more information on choosing a lo- cation. Rack Mounting T wo kits are available for rack mounting the base station. The first kit rack mounts a single base sta- tion in a 19" rack. The secon[...]

RF T ransmit Mode Switch Allows the operator to select three different types of transmitting modes; continuous transmit, transmitter off, or remote transmitter . For most operations, place the transmitter switch in the “CONT” position (Continuous mode). In the Continuous mode the RF transmitter will be on at all times regardless of whether the [...]

Audio Channel Switch Intercom T ype Set to T elex Selects either “IC 1 or 2" (and corresponding pins on ”IC Loop-thru"). In “Auto” position the switch allows selection of channels 1 or 2 from the beltpack. Figure 23 Audio Channel Switch Intercom T ype Set to RTS Selects R TS channel 1 or 2 on both I/C jacks (and corresponding Pins[...]

Figure 27 Auxiliary to I/C Switch Figure 28 Connecting Base Stations T ogether Interconnection to a Hard-W ired Inter com System The Radiocom wireless system can be integrated into Audiocom (T elex) intercom systems and most existing wired intercom systems including R TS and Clear-Com. Connect the intercom cable to the back of the base station. The[...]

-15- HEADSET LINES HEADSET LINES TWO CH BEL TP ACK (BP-2000) TWO CH BEL TP ACK "Y" HEADSET LINES HEADSET LINES HEADSET LINES T elex T elex INTERCOM POWER SUPPL Y (PS-2000L) INTERCOM USER ST A TION (US-2000A) CABLE (BP-2000) ONE CH BEL TP ACK (BP-1000) ONE CH BEL TP ACK (BP-1000) ONE CH BEL TP ACK (BP-1000) BTR-600 INTERCONNECT CABLES 12-1[...]

-16- T elex T elex T elex T elex HEADSET LINE HEADSET LINE HEADSET LINE MODEL PS15 POWER SUPPLY O/N 9000678600 IMPEDANCE SELECT NORM 200 DUAL 400 OUTPUTS J1, J2 CONNECT TO J1 J2 TW INTERCOM SYSTEM COMPONENTS REFER TO OPERATION MANUAL AUDIO COUPLING CM1-CM2 J3 TIP-CH1 RING-CH2 SLEEVE-COM RTS SYSTEMS, BURBANK CALIFORNIA MADE IN U.S.A. FUSE 0.5A S8/12[...]

Auxiliary Audio Connection The 6 pin telephone jack (RJ-1 1) may be used to supply audio into and out of the base station. R TS Matrix type intercoms may be interfaced to the base station through this jack. Since audio is not “Channelized” through this jack, the audio channel switch has no effect on the audio passed through the jack. The audio [...]

Beltpack Set-Up Headset Connection Insert the headset/microphone into the connector on the bottom on the unit. See the headset connection diagram (Figure 8) if a unit other than T elex headset is used. Figure 33 Connecting Headset RF T ransmit/Receive Channel Switches Allows the user to select which of the two RF chan- nels the unit is on. The tran[...]

Battery Installation Insure that the OFF/ON volume control knob is turned OFF . Press down the battery release latch and remove battery pack. Pack slides off in opposite direction. Replace batteries as follows: Figure 36 Battery Installation -19- 1. Open the battery pack by inserting finger nail and lifting as shown. 2. Pull battery strap to remove[...]

Pr e-W alk-Thru Checklist Following the instructions fully to this point you have successfully completed the following check- list: ❒ Located the base station properly . ❒ Connected power to base station transceiver . ❒ Connected the 1/2-wave antennas to the base station. Check frequency range of the antenna with the frequency of the base sta[...]

System Operation Base Station Operation Power If you have followed the instructions until this point you should now be ready to turn both the beltpack and the base station “ON” Place the power switch on the base station in the “ON” position. The green power on indicator LED should illuminate. Figure 37 Base Station Power Switch Push-to-T al[...]

Dual Listen Level This control is related to the dual listen switches. It controls the level of the audio mix. For more infor- mation on the dual listen switches, refer to the “Base Station Set-Up” section. Figure 40 Dual Listen Level Control Intercom Level I/C IN Adjusts the level of the Intercom system’ s audio into the base station. The In[...]

Beltpack Operation Power/Local Headset V olume Y ou should now be ready to turn the beltpack “ON”. Rotate the OFF/ON V olume Control Switch on the beltpack clockwise to turn the unit on. Figure 42 Off/On V olume Contr ol Switch Battery Check As you rotate the OFF/ON volume control knob clockwise to turn the unit on, note that the battery LED (L[...]

Figure 45 Microphone Gain Sidetone Level Regular TR beltpacks have their sidetone control lo- cated on their respective base stations (See the sidetone level part of the base station “Operation Section”). Specially ordered beltpack to beltpack (Mirror Im - age) direct communication units have their sidetone controlled by a control on the beltpa[...]

Example System Configurations Single Base Station Audiocom (T elex) System The audio out RCA jack on the back of this unit is used for the public address system. The unused Audiocom channel must be terminated to avoid loud feedback if audio channel two was switched to by the beltpack. The audio out of the base station’ s RCA jack is the audio cha[...]

Single Base Station R TS System Figure 48 Example Single BTR-500 R TS System used at a Small Play Pr oduction -26- 1C H DISTRIBUTION P ANEL RTS BACKST AGE MANAGER CURT AIN DIRECT OR ST AGE LIGHTS AUDIO SPOTLIGHT WIRED BEL TP ACKS POWER SUPPL Y RTS AUDIO CHANNE L1=S T A G EA N D DIRECTION AUDIO CHANNEL 2 = AUDIO EFFECTS/LIGHTING/CURT AIN B.P . 1C H [...]

Six Base Station R TS System Figure 49 Example of Six BTR-500 R TS Systems used by a Pr oduction Unit -27- T elex T elex T elex T elex T elex T THIS END TOWARD TRANSMITTER ALP-450 ex el R TRANSMIT ANTENNA TRANSMIT DC OUTPUT RECEIVE RECEIVE ANTENNA 110/220VAC INPUT FUSE: F 1.5A 250V AUX PUSH PUSH ANT. 1 5 6 9 1 5 6 9 1/C SC600 RTS POWER SUPPL Y RTS [...]

Figure 50 Example of an Eight BTR-600C Audiocom(T elex) System being used by a Football T eam -28- T elex T elex T elex TRANSMIT ANTENNA TRANSMIT DC OUTPUT RECEIVE RECEIVE ANTENNA 110/220 VACINPUT FUSE: F 1.5A 250V AUX PUSH 1 5 6 9 1 5 6 9 SC600 A B AUX PUSH PUSH 1 5 6 9 1 5 6 9 AUX PUSH 1 5 6 9 1 5 6 9 AUX PUSH PUSH 1 5 6 9 1 5 6 9 AUX PUSH 1 5 6 [...]

Beltpack to Beltpack System The following is an example of a beltpack to beltpack system. The two operators need to be in constant, full-duplex communication with each other in a noisy paper press environment. Figure 51 Example of a TR-500 System used at a Publishing Firm -29- T elex RF TX = FREQ 1 RF RX = FREQ 2 T elex RF TX = FREQ 2 RF RX = FREQ [...]

System W alk-Thru Now that you have successfully “set up” your T elex W ireless Intercom System and turned on any auxil- iary equipment you are ready to test the overall per- formance by “W alking” the T elex system through the areas in which you will be using it. Before you begin your walk-thru, check the follow- ing: ❒ Beltpack Battery [...]

TROUBLESHOOTING Reread the sections of this manual to make sure you have completed system set-up properly If you are unable to solve the problem, contact the dealer from whom you purchased the system for as- sistance. -31- PROBLEM SOLUTION DISTOR TION - System’ s audio quality seems distorted at medium to high input levels. Reduce microphone gain[...]

T ech T ips Codes Settings and the BTR600C While the BTR-600C and corresponding TR-600C have over 65,000 different codes that may be se - lected by the user , there are actually over 16 million different codes in the units. The microprocessor in each base station and corresponding beltpack has two unique numbers programmed into them from the factor[...]

-33- RTS Input Impedance: ..............................................200 W Output Level: ............................0.775 V rms nominal Bridging Impedance: ......................................>10k W Call Signalling: Send: ...................20kHz ± 100 Hz, 240 mV rms Receive: .............20kHz ± 800 Hz, 100 mV rms Power V oltage: ......[...]

Accessories and Replacement Parts ALP-600 520-760 MHz Bi-Directional Log Periodic Antenna Includes mounting hardware and 10 feet (3 meters) of coaxial cable with TNC Connectors Order No. 878896 Antenna Cables : Special low loss antenna cables with TNC Connectors. 1/2-W ave Antenna ALP-450 450-900 MHz Log Periodic Antenna Includes mounting hardware [...]

-35- CUST OMER SER VICE INFORMA TION If your receiver or transmitter should need servicing, please contact: Customer Service Department TELEX COMMUNICATIONS, INC. 8601 East Cornhusker Highway, P.O. Box 5579, Lincoln, Nebraska 68505-5579 U.S.A. Phone: (402) 467-5321 or 465-7021 All claims of defect or shortage should be sent to the above address. Wh[...]

-36- FCC INFORMA TION The Telex BTR-500/600C and the TR-500/600C Transmitter/Receiver are Type Ac- cepted under United States Federal Communications Commission Part 74. Licensing of Telex equipment is the User’s responsibility and licensibility depends on the user’s classification, users application, and frequency selected. Telex strongly urges[...]

R TELEX COMMUNICATIONS, INC. • 12000 Portland Ave. South, Burnsville, MN 55337. PN 801567-2 JAN 2001 Made in U.S.A.[...]