Français dropdown-ico

Toshiba B-852-R manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Toshiba B-852-R. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Toshiba B-852-R ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Toshiba B-852-R décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Toshiba B-852-R devrait contenir:
- informations sur les caractéristiques techniques du dispositif Toshiba B-852-R
- nom du fabricant et année de fabrication Toshiba B-852-R
- instructions d'utilisation, de réglage et d’entretien de l'équipement Toshiba B-852-R
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Toshiba B-852-R ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Toshiba B-852-R et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Toshiba en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Toshiba B-852-R, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Toshiba B-852-R, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Toshiba B-852-R. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    PRINTED IN JAPAN TOSHIBA Thermal Printer B-852-R SERIES Document No. EO18-33018 Original Mar., 2006 (Revised ) Maintenance Manual[...]

  • Page 2

    EO18-33018 TABLE OF CONTENTS Page 1. UNPACKI NG -------------------------------------------------------------------------------------------- 1- 1 1.1 PROCEDURES --------------------------------------------------------------------------------------------- 1- 1 1.2 CHECKS -------------------------------------------------------------------------------[...]

  • Page 3

    1. UNPACKING EO18-33018 (Revision Date: Sep. 28, 2007 1.1 Procedure 1- 1 1. UNPACKING 1.1 Procedure 1) Open the carton. 2) Unpack the accessories from the carton. 3) Unpack the pads and the printer from the carton. Supply Holder Frame (L) and (R) Supply Holder Base Power Cord Print Head Cleaner Owner’s Manual B-852-R Printer Bottom Pad Supply Hol[...]

  • Page 4

    1. UNPACKING EO18-33018 (Revision Date: Sep. 28, 2007) 1.2 Checks 1- 2 4) Remove the five pieces of tape from the printer. 5) Open the top cover. 6) Remove the one piece of tape. 7) Press down the head block release lever (1) and raise the print head block (2). 8) Remove the print head pad (3). 9) Place the printer on a level surface. 10) Please at[...]

  • Page 5

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.1 OPENING AND REMOVING THE COVERS 2-1 2. MAJOR UNIT REPLACEMENT 2.1 OPENING AND REMOVING THE COVERS 1) Turn the power off. 2) Open the top cover. 3) Remove the three B-4x6 screws to detach the side cover R. NOTE: After removing the screws, unhook the side cover R from portion A b y lifting and moving it toward[...]

  • Page 6

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.1 OPENING AND REMOVING THE COVERS 2-2 NOTE: After removing the screws, unhook th e side cover L from portion B by lif ting and moving it toward the front of the printer . 5) Disconnect the operation panel harness from CN13 on the MAIN PC Board. NOTE: Instructions to open the top cover and to detach the side co[...]

  • Page 7

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.3 Replacing the MAIN PC Board 2-3 2.3 Replacing the MAIN PC Board 1) Prior to replacing the MAIN PC board, print out the parameter settings for future reference. 2) Remove the side cover L from the printer. (Refer to Section 2.1.) 3) Remove the three SMW-3x6 screws to detach the rear frame cover. 4) Disconnect[...]

  • Page 8

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.3 Replacing the MAIN PC Board 2-4 4) Remove the two SMW-4x8 screws, SMW-3x6 screw and B-3x6 screw . 5) Disconnect the power harness from CN8 on the MAIN PC board ass’y , then remove the MAIN PC board ass’y from the printer . SMW-3x6 Screw SMW-4x8 Screw B-3x6 Screw MAIN PC Board Ass’ y MAIN PC Board Ass?[...]

  • Page 9

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.3 Replacing the MAIN PC Board 2-5 6) Remove the two B-3x6 screws and the two SMW-3x6 screws, then remove the MAIN PC board from the MAIN PCB support frame. 7) Replace the MAIN PC board with a new one, and reassemble in the reverse order of removal. 8) After replacing the MAIN PC board, perform the following op[...]

  • Page 10

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.4 Replacing the Panel PC Board 2-6 2.4 Replacing the Panel PC Board 1) Remove the side cover L from the printer. (Refer to Section 2.1.) 2) Remove the PT-3x8 screw to detach the operation panel ass’y from the side cover L in the direction indicated by the arrow. 3) Disconnect the operation panel harness from[...]

  • Page 11

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.4 Replacing the Panel PC Board 2-7 5) Remove the two PT -3x6 screws and W-4 washers to det ach the panel PC board from the operation panel cover . 6) Replace the panel PC board with a new one, then reassemble in the order removal. 7) T urn the power on, then confirm that the LCD message is displayed properly .[...]

  • Page 12

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.5 Replacing the S tepping Motor 2-8 2.5 Replacing the S tepping Motor 1) Remove the side cover L and MAIN PC board ass’y from the printer . (Refer to Sections 2.1 and 2.3.) 2) Remove the two SMW-3x6 screws to det ach the PCB support plate from the printer . 3) Remove the two SM-4x8 screws to detach the stepp[...]

  • Page 13

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.5 Replacing the S tepping Motor 2-9 NOTE: Apply FLOIL to the stepping m otor ’s pulley and the m otor gear when reassembling the stepping motor . Motor Gea r Pulley Stepping Moto r[...]

  • Page 14

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.6 Replacing the Head Up Sensor , Slit Sens or (Rewind/Feed) and Ribbon Motor (Rewind/Feed) 2-10 2.6 Replacing the Head Up Sensor , Slit Sensor (Rewind/Feed) and Ribbon Motor (Rewind/Feed) Prior to replacing the sensors or ribbon motor , perform the following operations. 1) Open the top cover . (Refer to Sectio[...]

  • Page 15

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.6 Replacing the Head Up Sensor , Slit Sens or (Rewind/Feed) and Ribbon Motor (Rewind/Feed) 2-1 1 3) Replace the head up sensor with a new one, then reassemble in the reverse order of removal. 4) Perform a test print to print to confirm that the printer works properly . NOTE: Be careful not to damage the slit s[...]

  • Page 16

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.6 Replacing the Head Up Sensor , Slit Sens or (Rewind/Feed) and Ribbon Motor (Rewind/Feed) 2-12 5) Push and release the hook A, then release the hook B to remove the slit sensor from the sensor holder . 6) Replace the slit sensor with a new one, then reassemble in the reverse order of removal. 7) Perform a tes[...]

  • Page 17

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.6 Replacing the Head Up Sensor , Slit Sens or (Rewind/Feed) and Ribbon Motor (Rewind/Feed) 2-13 NOTES: 1. Af ter replacing the ribbon motor , refer to Section System Mode Manual to perform a Maintenance Counter clear . 2. Secure the ribbon motors while inserting a 0.1 mm-thick p aper (or folded backing paper) [...]

  • Page 18

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.7 Replacing the Platen 2-14 Print Head Head Block Release Lever 2.7 Replacing the Platen 1) Prior to replacing the platen, print out the maintenance counter for future reference. 2) Open the top cover , and raise the print head block by pressing down the head block release lever . 3) While pulling the top part[...]

  • Page 19

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.7 Replacing the Platen 2-15 6) Replace the platen with a new one, then reassemble in the reverse order of removal. NOTE: When reassem bling, confirm the orient ation of the shaft holder . (See the picture below .) 7) Perform a test print to confirm that the printer works properly . Shaft Holder Platen[...]

  • Page 20

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.8 REPLACING THE MEDIA SENSOR 2-16 2.8 REPLACING THE MEDIA SENSOR 2.8.1 Feed Gap Sensor (TR) and Black Mark Sensor (Upper Side) 1) Open the top cover and raise the print head block. 2) Pull up the two tabs of the sensor case cap to remove it from the sensor block. 3) Remove the feed gap sensor (TR) and black ma[...]

  • Page 21

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.8 REPLACING THE MEDIA SENSOR 2-17 2.8.2 Feed Gap Sensor (LED) and Black Mark Sensor (Lower Side) 1) Remove the platen holder R, platen holder L, platen, and strip plate from the printer 2) Remove the SMW-4x8 screw to det ach the front cover from the printer . 3) Unhook the two springs. 4) Remove the two SMW-3x[...]

  • Page 22

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.8 REPLACING THE MEDIA SENSOR 2-18 NOTES: 1. When reassembling the sensor case cap, fit the hooks of the sensor case into portion A of the sensor case cap. 2. When reassembling the sensors, align the pins on the sensor case with the holes of the sensors. 3. Connect the harness including the green wire to the bl[...]

  • Page 23

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.9 REPLACING THE PRINT HEAD 2-19 2.9 REPLACING THE PRINT HEAD 1) Open the top cover and raise the print head block. 2) Push the print head ass’y to the right side, lift it in the direction of the arrow, and release it from the print head fixing pin. 3) Disconnect the print head harnesses from the three connec[...]

  • Page 24

    2. MAJOR UNIT REPLACEMENT EO18-33018 (Revision Date: May 21, 2007) 2.10 Replacing the PS Unit and Reactor 2-20 2.10 Replacing the PS Unit and Reactor NOTE: The reactor is installed in the B-852-TS22-QP-R and B-852-TS22-CN models. 1) Remove the side covers L, side cover R and MAIN PC Board from the printer. 2) Raise the print head block. 3) Remove t[...]

  • Page 25

    2. MAJOR UNIT REPLACEMENT EO18-33018 (Revision Date: May 21, 2007) 2.10 Replacing the PS Unit and Reactor 2-21 5) Disconnect the PSU harness from CN4 on the PS unit. 6) Disconnect the harnesses from CN1 on the PS unit. For the QP and CN models, disconnect the harness from CN2, too. 7) Remove the two SMW-4x8 screws to detach the PS unit from the PSU[...]

  • Page 26

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.10 Replacing the PS Unit and Reactor 2-22 9) Replace the PS unit or reactor with a new one, then reassemble in the reverse order of removal. WARNING! Pass the reactor harness and inlet harness through the cut in the PS unit frame. Care must be taken not to pinch the harnesses in the frame. Failure to do this m[...]

  • Page 27

    3. PERIODIC MAINTENANCE PROCE DURE EO18-33018 3. PERIODIC MAINTENANCE PROCEDURE 3-1 3. PERIODIC MAINTENANCE PROCEDURE All machines are generally delivered in their best condition. To maintain optimal operating condition and help gain maximum performance and life of machines, we would recommend you to conduct periodic maintenance. Doing this is also[...]

  • Page 28

    3. PERIODIC M AINTENANCE PROCEDURE EO18-33018 3. PERI ODIC MAI NTENANCE PROCEDURE 3-2 3) Clean the print head elements with the T O SHI BA T EC-approved print head cleaner . (Please instruct your cust om er s to clean them daily .) 4) Remov e any paper dust and glue of t he label. W ipe off moving rang e of t he m edia sensor . Print Head Cleaner P[...]

  • Page 29

    3. PERIODIC M AINTENANCE PROCEDURE EO18-33018 3. PERI ODIC MAI NTENANCE PROCEDURE 3-3 5. Apply FLOIL G-488 to t he cut ter unit using a soft cloth. 6. Clean the Cutter Blade with a cotton swab moistened with absolute ethyl alcohol. 7. Confir m t hat the problem occur s as r epor t ed, and then tak e corrective action. 8. Replace the f ollowing part[...]

  • Page 30

    3. PERIODIC MAINTENANCE PROCE DURE EO18-33018 3. PERIODIC MAINTENANCE PROCEDURE 3-4 1 1. Clean the outside of the printer . 12. Fill out a report form. Hand it to the manager and obtain a signature.[...]

  • Page 31

    4. TROUBLESHOOTING EO18-33018 4. TROUBLESHOOTING 4- 1 4. TROUBLESHOOTING Problems Cause Solution Power does not turn ON. 1. Input voltage to the printer is not within the rated voltage. 2. Output voltage from the printer is not within the rated voltage. 3. No voltage to the MAIN PC board. 4. Failure of MAIN PC board. Replace the power cable or powe[...]

  • Page 32

    4. TROUBLESHOOTING EO18-33018 4. TROUBLESHOOTING 4- 2 Problems Cause Solution Media feed failure 1. Media is not set properly. 2. Poor media quality 3. Improper adjustment of the feed gap sensor or black mark sensor. 4. Threshold is improper. 5. Failure of the feed gap sensor or black mark sensor 6. The cutter mechanism is not installed properly. 7[...]