Toshiba M200-ST2002 manuel d'utilisation

G M A D0 0128010 05/07 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Global Support Centre Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 158 in this gui de. Satellite ® M200/M20[...]

2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling . Model: Satellite ® M200/M205 Series Recordable and/or ReWritable Drive(s) and Associated Software W arranty The computer system you purchased m[...]

3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical applications, connections to implanted medi cal de vi ces, commercial transportation, nuclear facilities or systems or an y other applicatio ns where pr[...]

4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n. Contact either: ❖ T oshiba’ s Support W eb si[...]

5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can. In order to do this, it may occas[...]

6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your al arm equipment. If you hav e questions abou t what will disable alarm equipment, consult your telephone compan y or a qualified installer . Instructions for IC CS[...]

7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology , and is compliant to: ❖ The IEEE 802.11 Standard on W ireless LANs (Rev ision A/B/G), as defined and approv ed [...]

8 5.375 x 8.375 ver 2.3 In some situations or en vironments, the use of W ireless LAN may be restricted by the proprietor of the b uilding or responsible representativ es of the organization. These situatio ns may for e xample include: ❖ Using the W ireless LAN equipment on board airplanes, or ❖ In any other en vironment where the risk of inter[...]

9 5.375 x 8.375 ver 2.3 The term “IC” before the equipment certif ication number only signifies that the Industry Canada technical specifications were met. T o prev ent radio interference to the licensed service, this device is intended to be operated indoors an d away from windo ws to pr ovide maximum shielding. Equipment (or its transmit ante[...]

10 5.375 x 8.375 ver 2.3 Modem W arning Notice Conformity Statement The equipment has been ap prov ed to [Commissio n Decision “CTR21”] for pan- European single terminal connection to the Public Switched T elephone Netw ork (PSTN). Howe ver , due to differences between the indi vidual PSTNs provided in dif ferent countries/re gions the approv a[...]

11 5.375 x 8.375 ver 2.3 1. Sticker Please put the following stick er on devices incorpora ting this product. 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. O F: This equipment uses OFDM modulation. 3 The interference range of this e[...]

12 5.375 x 8.375 ver 2.3 J AP AN APPR O V ALS INSTITU TE FOR TELECOMMUNICA TIONS EQUIPMENT Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Ap prov al Number: 03NY .A0018, 03GZD A0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wire less module into other device. ❖ 5.17 GHz [...]

13 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries 802.11a (5 GHz) België/ Belgique: For pri vate usage outside b uildings acr oss public grounds over less than 300m no special regi stration with IB PT/BIPT is required. Registration to IBPT/BIPT is required for pri vate us age outside b u[...]

14 5.375 x 8.375 ver 2.3 Tu r b o Mo d e ( 5 G H z ) Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply . The user should use the wireless LAN util[...]

15 5.375 x 8.375 ver 2.3 ❖ This device must be used with Acce ss Points that hav e employed and acti vated a radar detection feature required for European Communi ty operation in the 5 GHz ba nds. This device will operate under the control of the Access Point in order to av oid oper ating on a channel occupied by an y radar system in the area. Th[...]

16 5.375 x 8.375 ver 2.3 802.11a (5 GHz) Tu r b o M o d e ( 5 G H z ) Approved Countries/Regions for use for the Intel ® PRO/ Wireless LAN 2100 3B Mini PCI Adapter This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Aust[...]

17 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the T oshiba Mini PCI Wireless LAN Card This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Approved Countries/Regions for use for the Intel ® PRO/Wireless [...]

18 5.375 x 8.375 ver 2.3 802.11a (5 GHz) Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g),[...]

19 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T e chnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio t echnology , and is compliant to: ❖ Bluetooth Specification as def ined and approv ed [...]

20 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table. Bluetooth ® Wireless T echnology and Y our[...]

21 5.375 x 8.375 ver 2.3 ❖ Using the equipment with Bluetooth wireless technology on bo ard airplanes, or ❖ In any other en vironment where the risk of interferen ce to other devices or services is perceiv ed or identified as harmful. If you are uncertain of the policy that applies on the use of wireless de vices in a specific or ganization or [...]

22 5.375 x 8.375 ver 2.3 The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations. Lo w power radio frequency electric machinery shall resist against interference from legal communications or from indu strial, scientific and medical radio emission electri[...]

23 5.375 x 8.375 ver 2.3 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to av oid the band of mobile object identification systems. 3. TOSHIB A Direct PC Monday – Friday: 10: 00 – 17:00 T oll Free T el: 0120-15-1048 Direct Dial: 03-3457-4 [...]

24 5.375 x 8.375 ver 2.3 Optical Drive Safety Instructions This appliance contains a laser syst em and is classified as a CLASS 1 LASER PRODUCT . T o use this model prop erly , read th e user’ s guide carefully and keep it for your fut ure reference. Never attempt to disass emble, adjust or repair a HD DVD, C D/DVD drive, CD-RW drive, Multi-drive[...]

25 5.375 x 8.375 ver 2.3 Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and ma y be subject to the approv al of the U.S. Department of Commerce prior to export. Any export, directly or indirectly , in contrav ention of the U.S. Export Ad ministration Re[...]

26 5.375 x 8.375 ver 2.3 T rademarks Satellite is a registered trademark of T o shiba America Information Systems, Inc. and/or T oshiba Corporation. Microsoft, W indows and W indows V ista ar e either registered trademarks or trademarks of Micros oft Corporation in the United States and/or other countries. DirectX, Active Desktop, DirectShow , and [...]

27 5.375 x 8.3 75 ver 2.3 Contents Introduction ................ ................................................................ 34 This guide ...............................................................35 Safety icons ............................................................36 Other icons used ...............................................[...]

28 Contents 5.375 x 8.3 75 ver 2.3 Using the computer fo r the first time ...................... 46 Opening the display panel ................................. 46 Your computer’s features and specifications ....47 Turning on the power ........................................47 Adding memory (optional) ...................................... 48 Ins[...]

29 Contents 5.375 x 8.3 75 ver 2.3 Moving the computer ........................................81 Using a computer lock ......................................82 Chapter 2: Learning the Ba sics ................................................. 83 Computing tips ....................................................... 83 Using the keyboard ...........[...]

30 Contents 5.375 x 8.3 75 ver 2.3 Chapter 3: Mobile Comput ing................................................. 101 Toshiba’s energy-saver design..............................101 Running the computer on battery power ..............101 Battery Notice ................................................. 102 Power management ..........................[...]

31 Contents 5.375 x 8.3 75 ver 2.3 Surfing the Internet .........................................127 Internet features ..............................................127 Uploading to, and downloading files from, the Internet ......................................128 Exploring audio features .......................................128 Recording sounds[...]

32 Contents 5.375 x 8.3 75 ver 2.3 CD/DVD Drive Acoustic Silencer ...........................152 TOSHIBA Accessibility .......................................... 153 ConfigFree™ ..........................................................154 Getting Started ................................................154 ConfigFree Utilities ...................[...]

33 Contents 5.375 x 8.3 75 ver 2.3 Other Toshiba Intern et Web sites ..........................190 Toshiba’s worldwide offices ..................................190 Appendix A: Hot Keys/TOSHI BA Cards ........... ...................... 192 Hot Key Cards .......................................................192 Using the Hot K ey Cards ..........[...]

34 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba notebook computer , your work and entertainment can accompan y you where ver you go. This notebook is compatible with European Union Dire ctive 2002/95/EC, Restriction of the use of certain Hazardous Substances in electrical and electronic eq[...]

35 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration i nformation are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrat ed. For more detailed information about the features and spec ifications on your particular model, please visit T os[...]

36 Introd uction Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipment, or loss of data. These safety cautions hav e been classif ied according to the seriousness of the risk, and icons highlight th[...]

37 Introduction Other documentation 5.375 x 8.375 ver 2.3 Other documentation Y our computer comes with the following documentation: ❖ An electronic version of the user’ s guide (this document ) ❖ It may also contain guides for other programs that may come with your system. For accessory information, visit T oshiba’ s W eb site at accessori[...]

38 Chapter 1 Getting Started This chapter provides tips for working comfortably , su mmarizes ho w to connect components, and ex plains what to do the f irst time you use your notebook computer. Selecting a place to work Y our computer is portable and designed to be used in a variety of circumstances and locations. Creating a computer -friendly env[...]

39 Getting Started Selecting a place to work ❖ Extreme heat, cold, or humidity . ❖ Liquids and corrosi ve chemicals. Keeping yourself comfortable The T oshi ba Instruction Manual for Safety and Comfort, included with your computer, contains helpful information for setting up your work en vironment and tips for working comfortably throughout the[...]

40 Getting Started Selecting a place to work ❖ Nev er turn off the computer if a dr i ve light indicates a driv e is activ e. T urning off the computer while it i s reading from or w riting to a disk/disc or flash media may damage the disk/disc or fl ash media, the dri ve, or both. ❖ Keep the computer and disks aw ay from objects that generate [...]

41 Getting Started Setting up your computer Setting up your computer TECHNICAL NOTE: Y ou must complete all setup steps up to and including “Setting up your software” on page 41 before adding external or internal components to your computer . These components include, but are not limited to, a mouse, keyboa rd, printer , memory , and PC Cards. [...]

42 Getting Started Re gistering your computer with T oshiba Registering your computer with T oshiba Product registration is strongly recommended, and allows T oshi ba to send you periodic updates, announcements , and special of fers applicable to your prod uct. Product registration can be completed during the initial start up process of your comput[...]

43 Getting Started Connecting to a po wer sour ce Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery . Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug dire[...]

44 Getting Started Connecting to a power so ur ce T o connect A C po wer to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord /cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other[...]

45 Getting Started Char ging the main battery The computer’ s main battery light gi ves you an indication of the main battery’ s current char ge: ❖ Glows amber while the main battery is being charged (A C adaptor connected) ❖ Glows blue when the main battery is fully char ged ❖ Is unlit when the main battery has discharged, the battery is[...]

46 Getting Started Using the computer for the fir st time Battery life and charge time may var y depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Facing the front of the com puter, locate [...]

47 Getting Started Using the computer for the f irst time Small bright dots m ay appear on your screen display wh en you turn on your computer . Y our di splay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology . An y small bright dots that may appear on your display are an intrins[...]

48 Getting Started Adding memo ry (optional) 3 Press and hold the power b utton in until the on/ of f light on the system indicator panel glows blue—about one second. (Sample Illustration) T urning on the power The preinstalled operating syst em will load automatically . When you turn on the computer for the first time, do not turn off the power [...]

49 Getting Started Adding memory (optional) If the computer has been running recently , the memor y module may be hot. The surrounding area may also be hot. Allow the module to cool to room temperature before replacing it. A void touching the cover , the module, and the surrounding area before they have cooled. Failure to follow these directions co[...]

50 Getting Started Adding memo ry (optional) 2 Click Shut Down . The operating system turns off the computer . 3 Unplug and remov e any cables connected to the computer , including the A C adaptor . 4 Remove the main battery . For information on removing the main battery , see “Removing the battery from the computer” on page 111 . 5 Close the d[...]

51 Getting Started Adding memory (optional) 8 Place the screw and the cov er in a safe place so that you can retriev e them later . Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. Avoid touchi ng the connector on the memory modul[...]

52 Getting Started Adding memo ry (optional) 12 Firmly press the mem ory module into the me mory slot’ s socket at approximately a 30-de gree angle (to the horizontal surface of the computer). (Sample Illustration) Inserting the memory module i nto the socket 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on[...]

53 Getting Started Adding memory (optional) (Sample Illustration) Inserti ng the memory m odule into the slot For this model Slot A is the bottom slot. Slot B is the top slot.If only one memory module is to be installed, it must be installed in slot A. 14 Replace the memory modu le slot cov er and secure it using the screw . 15 Re-insert the main b[...]

54 Getting Started Adding memo ry (optional) Do not try to remove a memor y module with the computer turned on. Y ou can damage the computer and the memor y module. Do not remove the memory module while the computer is in Sleep or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of[...]

55 Getting Started Adding memory (optional) 3 Gently lift the me m o ry module to a 30-degree angle and slide it out of the slot. (Sample Illustration) Removing the memory module 4 Replace the memory modu le slot cov er and secure it using the screw . 5 Re-insert the main battery . For mo re information on inserting the main battery , see “Insert[...]

56 Getting Started Har d Drive Recovery Utilities From time to time, Windows ® will display a pop-up that says, “Windows ® needs your permission to continue.” This is a security feature to prevent programs or people from doing things on your computer without your permission. If you were trying to perform the action, click Continue; otherwise,[...]

57 Getting Started Har d Drive Recovery Utilities Creating Recovery CDs/DVDs Depending on your system con figuration, you may be able to copy the Hard Driv e Recov ery Utilities to CD or D VD which gives you the ability to recov er your hard di sk driv e and recov er your system if the hard driv e recovery partition has been deleted or the h ard di[...]

58 Getting Started Har d Drive Recovery Utilities 3 Select the items you want to copy by clicking the check box next to the item’ s Name—recov ery files, applications (original bundled dri vers and applications), or both the recov ery files and applications. 4 Click Crea te . 5 Insert the first blank CD or D V D into your writable optical driv [...]

59 Getting Started Har d Drive Recovery Utilities Hard Disk Drive Recovery using the recover y partition Y ou hav e the options of recov ering your system using the Hard Driv e Recov ery partition to the factory-set default, or recovering just your C: drive and leaving other partitions (for example, a D: dri ve) intact, or changing the size of your[...]

60 Getting Started Har d Drive Recovery Utilities Recovering the original factory image (recommended recovery method) Recovering a hard disk drive to its out of box state deletes all partitio ns on the hard disk drive and you r information will be lost. Be sure to save your work to external media first. 1 On the T oshiba Recovery W izard screen, se[...]

61 Getting Started Har d Drive Recovery Utilities Erasing the hard disk The Recov ery W izard allo ws you to delete all data and partitions from the hard di sk. T o delete the data and partitions from your hard disk: 1 On the T oshiba Recovery W izard screen, select Erase the hard disk , and then click Next . 2 The next screen lists the two methods[...]

62 Getting Started Har d Drive Recovery Utilities Recovering the C: partition of the HDD without changing the current partition size Recovering the C: drive to its factory default setting reformats your drive and your information on the recovered drive will be lost. Be sure to save your work to external media first. If you have created other partit[...]

63 Getting Started Har d Drive Recovery Utilities 4 Click Next to begin the restoration. Once comp lete, a message displays that the HDD has been recov ered. 5 Press any ke y on your keyboard to restart the computer . Hard Disk Drive Recovery using the Recover y media If you need to recover your computer to its default factory state, you can rebuil[...]

64 Getting Started Using the T ouchP ad™ Checking the HDD operating status After restoring your hard disk driv e, you can check its status as follows: 1 Click Start . 2 Right-click Computer . 3 Select Manage . 4 Click Disk Managem ent . 5 Highlight the hard disk dri ve in the V olume list to display its status in the lower portion of the screen. [...]

65 Getting Started Using external display de vices Because the T ouchPad is much smaller than the display screen, moving your cursor acros s the screen often means having to move your finger several times across the T ouchPad in the preferred direction. Once you hav e positioned your cursor , you can click it into place b y either double-tapping th[...]

66 Getting Started Using external display de vices Before connecting an external monitor or vide o projector , configure your computer for the t ype of de vice you are connecting. T o do this, refer to the documentation for your operating system and devices. Connecting an external monitor or projector Y ou can easily attach an exte rnal monitor or [...]

67 Getting Started Using an external k e yboard ❖ Built-in display and external monitor (extended desktop) ❖ Built-in display and TV (extended desktop) ❖ Swap—Swi tch primary displ ay between internal display and external monitor when using extended desktop (Sample Image) Display options window 3 Release the Fn key . Adjusting the quality o[...]

68 Getting Started Connecting a printer Connecting a printer Y our printer documentation may require you to install the printer software before physically connecting the printe r to your computer . If you do not install the software as instructed by the printer manufacturer , the printer may not function correctly . Read the documentation that came[...]

69 Getting Started Connecting an optional external disk ette drive 1 Click Start , Control Panel , Hard ware and Sound , and then under Printers , click A dd a printer . The Add Printer W izard appears. (Sample Image) Add Printer W izar d 2 Follo w the on-screen instructions to set up your printer . Connecting an optional external diskette drive So[...]

70 Getting Started T urning off the computer T o connect an optional e xternal USB diskette dri ve, connect the cable to one of the comput er’ s USB ports. (Sample Illustration) Connecting a n optional external USB diskette drive T urning off the computer Pressing the power button before shutting down the Windows ® operating system could cause y[...]

71 Getting Started T urning off the computer TECHNICAL NOTE: Before using the Shut Down option to turn off your computer , save your files and make sure all disk/disc activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again. ❖ Use the Sleep command to save y[...]

72 Getting Started T urning off the computer Sleep mode The Sleep command places the comput er into a po wer-saving mode. Sleep sa ves the current state of the computer to memory so that, when you restart the comp uter , you can continue working from where you left of f. After your computer sleeps for an extended period of time, the Windows ® oper[...]

73 Getting Started T urning off the computer Using the Shut Down command The Shut do wn command complet ely shuts do wn the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns of f your computer . Use the following steps to turn of f your [...]

74 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. (Sample Image) Advanced settings tab of P ower Options scr een 4 Click Power buttons and lid to display the actions that you can configure. 5 Select the options you want from the drop-down lists. Thes[...]

75 Getting Started T urning off the computer 6 Click App ly . 7 Click OK . Once the computer is conf igured, you can turn it off b y either pressing the power b utton or closing the display pane l, depending on the options set . Restarting your computer T o start the computer up again, press the po wer b utton unt il the on/off light glows blue. If[...]

76 Getting Started T urning off the computer Configuring Hibernation mode options Y ou can place the computer into Hibernation mode b y either pressing the power b utton or closing the display panel. Y ou can also specify an amount of time after which the computer automatically goes into Hibernation mode. T o use an y of these methods, you first ne[...]

77 Getting Started T urning off the computer 5 Select Hibernate for the options you want. These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the d[...]

78 Getting Started T urning off the computer Using and configuring Sleep mode T o turn off the com puter using the Sleep command: 1 Click Start , and then click the arro w ne xt to the Lock button in the lower -right part of the Start menu. The Shut Down menu appears. (Sample Image) Shut Down menu 2 Click Sleep . The computer sa ves the status of a[...]

79 Getting Started T urning off the computer 2 Click Change plan s ettings under the po wer plan to be customized. The Edit Plan Settin gs window appears. (Sample Image) Edit Plan Settings screen 3 T o change the amount of time af ter which the computer enters Sleep mode: ❖ Under Put the computer to sleep , select the desired amount of time in bo[...]

80 Getting Started T urning off the computer 5 Click Power buttons and lid to display the actions that you can configure. 6 Select Sleep for the options you want. These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Sleep if y[...]

81 Getting Started Customizing your computer’ s settings Customizing your computer’ s settings There are sev eral ways in which you can customize your computer to suit your particular requir ements. Refer to your operating system documentation or Help an d Support for details. Y ou may also wish to customize your power usage settings. F or more[...]

82 Getting Started Caring for your computer Using a computer lock Y ou may want to secure your comput er to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com . (Sample Illustration) Computer lock cable T o secure[...]

83 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the disk. If the network you are using goes down and you must restart your compu ter to reconn[...]

84 Learning the Basics Computing tips ❖ Back up your files to disks (or other remov able media) on a regular basis. Label the backup co pies clearly and store them in a safe place. It is easy to put of f backing up because it takes time. Ho wev er , if your hard disk suddenly fails, you w ill lose all the data on it unless you have a separate bac[...]

85 Learning the Basics Using the ke yboar d Using the keyboard Y our computer’ s ke yboard contai ns character keys, control ke ys, function ke ys, and special W indo ws ® k ey s , providing all the functionality of a full-size keyboard. (Sample Illustration) Ke yboar d Character keys T y ping with the character keys is very muc h li ke t yp ing[...]

86 Learning the Basics Using the ke yboar d Ctrl, Fn, and Alt keys (Sample Illustration) Ctrl, Fn, and Alt keys The Ctrl , Fn , and Alt keys do different things depending on the program you are using. For more inform ation, see your program documentation. Function keys The function k eys (no t to be confused with the Fn key) are the 12 keys at the [...]

87 Learning the Basics Using the ke yboar d Overlay keys The ke ys with gray numbers and symbols on the front of them form the numeric and cursor ov erlay . This overlay lets you enter numeric data or control the cursor as you would using the 10-key ke ypad on a desktop comput er’ s k eyboa rd. (Sample Illustration) Numeric and cursor contr ol ov[...]

88 Learning the Basics Starting a pr ogr am Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. T o find the file, use the Start menu or W indo ws ® Explorer . If you prefer to open the program f i rst, you hav e four options. Y ou can: ❖ Double-click th[...]

89 Learning the Basics Starting a pr o gram Starting a program from Windows ® Explorer If a program is not listed in th e All Programs menu, yo u can start it from W indows ® E xplorer . W indo ws ® Explorer gi ves you a vie w of your computer’ s contents as a hi erarchy or “tree. ” Y ou can easily see the contents of each driv e and folde[...]

90 Learning the Basics Saving your work Starting a program using the Start Search field This example uses the Start menu’ s Start Search f ield to start Wo r d P a d : 1 Click Start to display the Start menu. The Start Search f ield appears at the bottom of the Start menu. (Sample Image) Start Sear ch field in Start menu 2 Start typing the progra[...]

91 Learning the Basics Saving your work Saving files 1 In your Windo ws ® -based application, click File , and then Sav e . 2 Click Browse f olders . If you are working with a docum ent that already has a f ile name, this is all you need to do. If y ou created a ne w document, your program displays a Sav e As dialog box. Use this dialog box to spe[...]

92 Learning the Basics Printing your work Using a file extension Most programs assign an extension to the f ile name that identifies the file as being created in the pr ogram with a particular format. F or example, Microsoft ® W ord saves f iles with a .doc extension. Any file name with an extension of “.doc” is assumed to be a Microsoft ® W [...]

93 Learning the Basics Backing up your work 3 Specify the print parameters. For e xample, the range of pages and number of copies to print. 4 Click Print . Backing up your work Back up all the files you create in case something happens to your computer . Y ou can back up your files to dif ferent types of media such as CDs, D VDs, diskettes, or to a[...]

94 Learning the Basics Using the optical drive TECHNICAL NOTE: Y our optical drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region. The drive will allow you to change regions four times. On the fourth change, the region will b[...]

95 Learning the Basics Using the optical drive Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Media control buttons (A vailable on certain models) The media control buttons located abov e the keyboard let you access the Internet when the computer is on and play audio CDs or D VD mov[...]

96 Learning the Basics Using the optical drive 4 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty , clean it as described in “Caring for CD or D VD discs” on page 100 . 6 Place the disc carefully in th e disc tray , label s[...]

97 Learning the Basics Using the optical drive 8 Make sure the disc is completely on the spindle and is lying flat on the tray . If you insert the disc incorrectly , it may jam the drive. If this happens, contact T oshiba support for assistance. 9 Push the disc tray in by pressing gently on th e center of the tray until it clicks into place. Y ou a[...]

98 Learning the Basics Using the optical drive The W indo ws Media ® Player control panel works much lik e an ordinary compact disc player: ❖ T o play the CD or to pause, click the Play/Pause button. ❖ T o stop the CD, click the Stop button. Before putting on headphones to listen, turn the volume down. Do not set the volume too high when using[...]

99 Learning the Basics Using the optical drive Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your T oshiba optical drive may not record on certain optical media that bear the applicable logo, or play back optical media recorded by other computers or o[...]

100 Learning the Basics T oshiba’ s online r esour ces 2 Pull the tray out until it is fully open , remov e the disc, and place it in its protecti ve co ver . 3 Gently press the tray in to close it. Caring for CD or DVD discs ❖ Store your discs in their original con tainers to protect them from scratches and k eep them clean. ❖ Do not bend a [...]

101 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your comput er while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process. It has a number of other features that enhanc e its energy ef ficiency .[...]

102 Mobile Computing Running the computer on battery power Battery Notice Battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as th e natural performance variations produced by the design of individual components. Published battery l[...]

103 Mobile Computing Char ging ba tteries Power management Y our computer ships with t he po wer management op tions preset to a configuration that will prov ide the most stable opera ting en vironment and optimum system performan ce for both A C po wer and battery modes. Changes to these settings may result in system performance or stability issue[...]

104 Mobile Computing Char ging batteries Charging the main battery T o charge the main battery while it is in your computer, plug the computer into a li ve electrical ou tlet. The battery char ges whether the computer is on or off. TECHNICAL NOTE: The recharging of the batter y cann ot occur when your computer is using all of the pow er provided by[...]

105 Mobile Computing Monitoring main battery power The above error message may vary by computer model. The RTC battery does not charge while the computer is turned off even when the AC adaptor is ch arging the computer . The RTC battery charges when the computer is powered on. If the R TC battery is lo w , the real-time clock and calendar may displ[...]

106 Mobile Computing Monitoring main battery power If the AC power light flashes amber during charging, either a battery pack is malfunctioning, or it is not receiving correc t input from the AC power supply . Disconnect the AC power cord/cable and remove the battery pack. See “Changing the main battery” on page 111 for information on replacing[...]

107 Mobile Computing Monitoring main battery power Determining remaining battery power Wait at least 16 se conds after turning on the computer before trying to monitor the remaining battery power . The computer needs this time to check the battery’ s remaining capac ity and perform its calculations. Highlight the power icon in the Notification Ar[...]

108 Mobile Computing Monitoring main battery power Setting batter y notifications Y ou can set two notif ications. Each notif ication can be set to alert you when a specified percentage of remaining battery po wer has been reached. Y ou can also set the computer to enter Sleep mode or Hibernation mode or to compl etely po wer do wn when the notif i[...]

109 Mobile Computing Monitoring main battery power ❖ How much you use the hard disk, optical driv e, diskette driv es, or other optional devices ❖ Where you are working, since operating time decr eases at low temperatures There are v arious ways in which you can conserv e power a nd extend the operating time of your battery: ❖ Enable Sleep or[...]

110 Mobile Computing Monitoring main battery power 2 Select an appropriate plan for your work en vironment or create your own custom plan. 3 Click Create a P ower Plan to set up a ne w plan. T o edit a plan or to edit advanced settings, continue to the following steps. 4 Click Change Pl an Settings to choose the plan you want to edit. This screen a[...]

111 Mobile Computing Changing the main battery 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Po wer Plan options are: Balanced, Power Sa ver , and High Performance. 3 Release the Fn key . The hot key card disappears. Y ou are now in the selected mode. Changing the main batter y When your main bat tery has ru[...]

112 Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlo cked position. (Sample Illustration) Unlocking the battery r elease loc k 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer . (Sample Illustration) Removing the battery If the battery is leaking or i[...]

113 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks. The battery pack has been designe d so that you cannot install i t with rev erse polarity . [...]

114 Mobile Computing T aking car e of your battery 4 T urn the computer right side up. 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 111 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life. S[...]

115 Mobile Computing T aking car e of your battery Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doi[...]

116 Mobile Computing Disposing of used b atteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you hav e fully rech ar ged the battery . Y ou must discard a batter y if it becomes damaged. Never attempt to dispose of a battery pack [...]

117 Mobile Computing T raveling tips T raveling tips The en vironmental precautions listed in “Selecting a place to work” on page 38 , also apply while traveling. ❖ Nev er leav e your computer on a sunny ledge or in a place where it could get wet or cov ered in dust. ❖ Always tra vel with the comput er in a carrying case. T oshiba of fers a[...]

118 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your notebook computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system. Y ou use i ts features to start programs, find documents, set up system components, a[...]

119 Exploring Y our Computer’ s Features Exploring the desktop Finding your way around the desktop Y our computer’ s desktop includes se veral standard features: icons, Start button, T askb ar , Notif ication Area, and back ground pattern. (Sample Image) W indows ® oper ating system desktop Icons An icon represents a folder , file, or program [...]

120 Exploring Y our Computer’ s Features Explorin g the desktop Y our desktop may contain othe r icons depending on your configuration. See W indo ws ® online Help for more specific information on each icon and ho w to use it. Start button Y ou use the Start button to: ❖ Start programs ❖ Open documents ❖ Adjust system settings ❖ Find fil[...]

121 Exploring Y our Computer’ s Features Setting up for communications Setting up for communications T o connect to the Internet or use an online serv ice, you need: ❖ A browser or communications program ❖ An Internet Service Pro vider (ISP ) or online service if you plan to use the Internet ❖ A way to connect to the ISP (for example modem/[...]

122 Exploring Y our Computer’ s Features Setting up for communications 7 Click OK to close the properties dialog box for that sp ecifi c modem. 8 Click OK to close the Phone and Modem Options d ialog box. 9 Close the Control P anel. Connecting a modem to a telephone line (A vailable on certain models) Y our computer may come with a built-in modem[...]

123 Exploring Y our Computer’ s Features Setting up for communications 2 Connect the other end to the RJ-11 wall jack. (Sample Illustration) Connecting to a wall jack Connect the built-in modem only to ordinary analog phone lines. Never connect the built-in modem to a digital line (ISDN). Never connect the built-in modem to the digital connector [...]

124 Exploring Y our Computer’ s Features Setting up for communications Setting up the connection T o set up an off ice connection, consult your network administrator for network settings and ad dition al considerations. T o set up a dial-up connection, us e the Connect to the Internet W izard: 1 Click Start , Control Panel , Netw ork and Inte rne[...]

125 Exploring Y our Computer’ s Features An overview of using the Internet Using Wireless LAN connectivity Wireless connectivity and some features may require you to purchase additional software, external hardware or services. Availability of public wire less LAN access points may be limited. Y our system may come with an optional wireless LAN mo[...]

126 Exploring Y our Computer’ s Features An overview of using the Internet The Wo rld Wide Web The W orld W ide W eb (or “W eb”) is a subset of the Internet—a collection of interlinked docum ents (located on computers connected to the Internet) that w ork together using a specific Internet protocol called Hyp ertext T ransfer Protocol (HTTP[...]

127 Exploring Y our Computer’ s Features An overview of using the Internet Surfing the Internet Once connected to the Internet, th e W eb browser displays a home page, for example, your ISP’ s home page on the Internet or your company’ s W eb site home page. T o visit a desired W eb site, type in the W eb ad dress. The W eb address, or Unifor[...]

128 Exploring Y our Computer’ s Features Explor ing audio feat ur es Uploading to, and downloading files from, the Internet T ransferring files from one co mputer to another is termed uploading (transferring data from your computer to a site on the W eb), or downloading (transferring data from a site on the W eb to your computer). There are sev e[...]

129 Exploring Y our Computer’ s Features We b C a m Using external speakers or headphones Y our computer is equipped with a full stereo sound system with internal speakers. Instead of usin g the internal speakers, you can connect headphones or a pair of external ste reo speakers. Before putting on headphones to listen, turn the volume down. Do no[...]

130 Exploring Y our Computer’ s Features Using PC Car ds Using PC Cards (A vailable on certain models) TECHNICAL NOTE: For PCMCIA-compatible PC Cards, check the package to make sure they conform to the PCMCIA 2.1 standard (or later). Other cards may work with y our computer , but are likely to be much more difficult to set up and use. Y our noteb[...]

131 Exploring Y our Computer’ s Features Using PC Car ds Removing a PC Card Be sure to disable the PC Card prior to removing it. Otherwise, the system may be damaged. Before removing a PC Card, make sure that no applications or system services are using the card. 1 Prepare the card for remov al by clicking the Sa fely Remove Hardwar e icon in the[...]

132 Exploring Y our Computer’ s Features Using an Expr essCar d™ Using an ExpressCard ™ (A vailable on certain models) The ExpressCard ™ slot supports the use of ExpressCard media. The slot also supports ho t swapping, which allo ws you to replace one ExpressCard with another while the computer is on. Inserting an ExpressCard ™ Before you[...]

133 Exploring Y our Computer’ s Features Using the Bridge Media Adapter Slot 4 Grasp the edges of the ExpressCar d and slide it out of the slot. (Sample Illustration) Removing an Expr essCar d T o prevent damage to the media card and/or Bridge Media Adapter slot, remove the media card before you carry or move the computer . Using the Bridge Media[...]

134 Exploring Y our Computer’ s Features Using the Bridge Media Adapter Slot 2 Push the media into the ad apter until it locks in place. (Sample Illustration) Inserting memory media When inserting memory media, do not touch the metal contacts. Y ou could expose the storage area to static electri city , which can destroy data. Removing memor y med[...]

135 Exploring Y our Computer’ s Features Using the i.LINK ® port Using the i.LINK ® port The i.LINK ® port on the side of the computer pro vides an extremely fast data transfer rate. In addition to high speed, the i.LINK ® port also supports isochronous data transfer (the delive ry of data at a guaranteed rate). This makes it ideal for device[...]

136 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help you to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain sys tem details, set additional options, or change de fault options. These utilities are described in this chapter . ❖ TOSHIB A Assi st ❖ Super[...]

137 Utilities TOSHIB A Assist TOSHIBA Assist The TOSHIB A Assist pro vides qui ck access to computer functions and allows you to customize a range of com puter settings. T o access TOSHIB A Assist, do one of the following: ❖ Double-click the TOSHIB A Assist shortcut icon on the desktop. ❖ Click Start , All Programs , To s h i b a , Utilit ies ,[...]

138 Utilities TOSHIB A Assist Connect The features av ailable in this category are: ❖ ConfigFree™ Connecti vity Doctor ❖ Bluetooth ® Settings ❖ Bluetooth ® Local COM Setting s (Sample Image) T OSHIBA Assist window – Connect tab[...]

139 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secure tab[...]

140 Utilities TOSHIB A Assist Protect & Fix The feature a vailable in this category is: ❖ TOSHIB A PC Diagnostic T ool Utility (Sample Image) T OSHIBA Assist window – Pr otect & F ix tab[...]

141 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ T oshiba Hardware Setup ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ CD/D VD Dri ve Acoustic Silencer ❖ TOSHIB A Accessibility (Sample Image) T OSHIBA Assist window – Optimize tab[...]

142 Utilities Setting passwor ds Setting passwords Setting a password lets you walk away from your computer , providing additional protection for your files. When you set a password, you must enter the password before you can wo rk on your computer again. T oshiba supports se ve ral types of passwords on you r computer: ❖ An instant password—Se[...]

143 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, T oshiba strongly recommends that you save your password in a location where you can later access it should you not r[...]

144 Utilities Setting passwor ds 7 Click OK if you want to save the password to a text file on a diskette or media of your choice, or click Cancel to continue without saving the password to a text f ile. 8 Shut down the system to complete the process. Deleting a supervisor password T o delete a supervisor passw ord: 1 Click Start , All Programs , T[...]

145 Utilities Setting passwor ds T o register a password for the po wer- on password functions: 1 Click Start , All Programs , To s h i b a , Utilit ies , and then TOSHIB A Passw ord Utility . The TOSHIB A P assword Utility windo w appears. (Sample Image) TOSHIB A P asswor d Utility window 2 Click Set . 3 Enter your pas sword, and then enter it aga[...]

146 Utilities TOSHIB A PC Dia gnostic T ool Utility TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose problem s with devices in your computer . Refer to the online Help documentatio n within the application for additional help. The TOSHIBA PC Diagnostic T ool u tility may show tests for features you do not have. This is normal and[...]

147 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contr ol Panel , and then Mouse under Hard ware and Sound , or click the Mouse icon in the Optimize tab of TOSHIB A Assi st . The Mouse Properties screen appears. (Sample Image) Mouse[...]

148 Utilities T o s h i b a H a rd w a re S e t u p T oshiba Hardware Setup T o shiba Hardware Setup is the T oshiba configuration management tool av ailable through the Windo ws ® operating system. T o access it: ❖ Click Start , All Programs , To s h i b a , Utilit ies , and then HWSetup , or clic k the T o shiba Hardwar e Setup icon in the Opt[...]

149 Utilities T o s h i b a H a rd w a re S e t u p ❖ CPU —Allows you to enable or disable CPU frequency switching modes Dynamically Swit chable —This mode is the default setting fo r your computer , and automatica lly changes the processing frequency and decreases voltage depending on the po wer source: ❖ AC P o w e r —If your computer i[...]

150 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Changing screen resolution” on page 206 ). Y ou may select all applications or any subset of the following: ❖ Microsoft ® Internet Explorer ® ❖ Microsoft ® Of f ice ❖ W indo [...]

151 Utilities TOSHIB A Button Support T o zoom in, hold down the Fn key and press 2 ; to zoom out, hold down the Fn ke y and press 1 . For more information about how to use the T OSHIB A Zooming utility , right-click the icon in the Notification Area and then click Help . 4 Click OK . TOSHIBA Button Support TOSHIB A Button Support allows you to cus[...]

152 Utilities CD/D VD Drive Acoustic Si lencer CD/DVD Drive Acoustic Silencer This utility can slow the speed of your optical driv e to make it run more quietly . Y ou can use this utility to m ake listening to music CDs more enjoyable. When you change the optical drive to “Quiet” mode, the setting is only valid for the current Windows ® sessi[...]

153 Utilities TOSHI BA A ccessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot ke y combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a sti cky key , meaning you can press it once, r[...]

154 Utilities ConfigF r ee™ ConfigFree ™ All references to Bluetooth ® in this section are applicable only if Bluetooth ® is available on your system. ConfigFree ™ is a set of utilities that makes it easy to control communication devices and networ k connections. Conf igFree also lets you identi fy communication problems and create prof ile[...]

155 Utilities ConfigF ree™ If your computer is not connected to a network, the ConfigFree icon in the Notification Area is displayed with an “X.” ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network connection problems. Using Connectivity Doctor , you can vie w detailed net[...]

156 Utilities ConfigF r ee™ Profile Settings The Prof ile Settings utility lets you save network settings in “profiles . ” ConfigFree prof iles are useful for easily switching network settings and devices.Y ou can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally , fo[...]

157 Utilities ConfigF ree™ 3 Click Open Settings . The ConfigFree Prof ile Settings windo w appears. (Sample Image) ConfigF ree Pr ofile Settings windo w 4 Click Add to start the Create Prof ile W izard.[...]

158 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter when using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself. It cov ers the problems you are most lik[...]

159 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask . Closing the failed prog ram should allow you to continue working. If it does not, c[...]

160 If Something Goes Wrong Pr oblems when you turn on the computer If you are using an A C adaptor , v eri fy that the computer is recei ving power from the external po wer source by looking at the A C power light. If the indicator is glo wing, th e computer is conn ected to a liv e external po wer source. The computer starts but when y ou pr ess [...]

161 If Something Goes Wrong Pr oblems when you turn on the computer If you are running on battery power , it is recommended that you do not lea ve the computer in Sleep mode for lo ng periods of time. T o char ge the battery , lea ve the computer plugged into a li ve wall outlet for sev eral hours. For more information see “Charging batteries” [...]

162 If Something Goes Wrong The W indo ws ® operating system is not working 5 V erify that the A C adaptor is th e correct unit for your computer model. The computer may not be abl e to start from an A C adaptor that is rated for less current (amperage) than the computer requires, e ven if the rated v oltage is correct, and the plug fits correctly[...]

163 If Something Goes Wrong The W indows ® operating system is not working ❖ Safe Mode with Command Pr ompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Kno wn Good Conf iguration (adv anced) ❖ Directory Services Restore Mode ❖ Deb uggin g Mode ❖ Disable automatic restar t on system failure ❖ Disable Driv er[...]

164 If Something Goes Wrong Resolving a hardwar e conflict The Windows ® operating system can help you If the operating system has started properly b ut you still have a problem using your co mputer , the online Help can assist you in troubleshooting the problem . T o access the W indo ws ® operating system Help and Su pport: 1 Click Start , then[...]

165 If Something Goes Wrong Resolving a har dwar e conflict The device most recently connected to the system is th e one most likely to be causing a conflict. Resolving conflicts There are sev eral things you can do to resolve hardw are conflicts: ❖ Get the most recent dri vers from the manuf acturer . ❖ Disable the device. For an ol der de vic[...]

166 If Something Goes Wrong Resolving a hardwar e conflict ❖ The Resources tab, which lists resources assigned to the monitor , optional external optical drive, optional external diskette dri ve, and other power -using functions. This tab does not appear if the device is not using resources. ❖ The Driver tab, which displays th e dri vers being [...]

167 If Something Goes Wrong Resolving a har dwar e conflict For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in slot A. Power and the batteries Y our computer recei ve s its po wer through the AC adaptor and power cord/cable or from the system batteries (battery , o[...]

168 If Something Goes Wrong Resolving a hardwar e conflict The battery appears not to power the computer f or as long as it usually does. If you frequently repeat shallo w charge and di scha rge, the battery meter may become in accurate. Let the battery discharge completely , then try charging it ag ain. Check the po wer options vi a your Po wer Pl[...]

169 If Something Goes Wrong Resolving a har dwar e conflict Nothing happens when you p ress the ke ys on the external keyboard. Y ou may hav e plugged the external keyboard in while the computer was turned on. Using the computer’ s T ouchPad: 1 Click Start , and then click the arro w ne xt to the Lock button in the lower -right part of the Start [...]

170 If Something Goes Wrong Resolving a hardwar e conflict The screen does not look right. Y ou can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Personalize . This opens the Personalization windo w . Click Windo ws Color and Appearance to choose the colors for the screen. Click[...]

171 If Something Goes Wrong Resolving a har dwar e conflict Small bright dots appear on yo ur TFT display when y ou turn on y our compu ter . Small bright dots m ay appear on your screen display wh en you turn on your computer . Y our di splay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precisio[...]

172 If Something Goes Wrong Resolving a hardwar e conflict 6 Y ou can choose one or both options: ❖ Automatically f ix f ile system er rors ❖ Scan for and attempt reco very of bad sectors 7 Click Start . Error- checking tests and repairs the disk. Y our hard disk seems very slo w . If you hav e been using your computer fo r a long time, your fi[...]

173 If Something Goes Wrong Resolving a har dwar e conflict Optical drive problems Y ou cannot access a disc in the driv e. If the optical dri ve is an e xternal driv e, make sure that the driv e’ s cable is properly connected to the computer . Make sure the tray that holds the CD or D VD is closed properly . Press gently until it clicks into pla[...]

174 If Something Goes Wrong Resolving a hardwar e conflict The disc will not come out of the dri ve when y ou click the eject button on the scr een. Press the b utton on the optical dri ve itself. Fo r additional information see “Y ou press the disc eject button, b ut the dri ve tray does not slide out. ” on page 173 . Sound system problems No [...]

175 If Something Goes Wrong Resolving a har dwar e conflict ❖ Occasionally a defecti ve PC Card slips through quality control. If another computer w ith a PC Card slot is a vailable, try the card in that machine. If the car d malfunctions again, it may be defectiv e. Resolving PC Card problems Here are some common problems and their solutions: Th[...]

176 If Something Goes Wrong Resolving a hardwar e conflict Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported. For more information on Hibernation and Sleep modes see “Hibernation mode” on page 71 and “Sleep mode” on page 71 . The system does not r ecognize your PC[...]

177 If Something Goes Wrong Resolving a har dwar e conflict ❖ Occasionally a defecti ve Expre ssCard™ slips through quality control. If another computer wit h an ExpressCard slot is av ailable, try the card in that machine. If the car d malfunctions again, it may be defecti ve. Resolving ExpressCard™ problems Here are some common problems and[...]

178 If Something Goes Wrong Resolving a hardwar e conflict Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported. For more information on Hibernation and Sleep modes see “Hibernation mode” on page 68 and “Sleep mode” on page 69 . The system does not r ecognize your Ex[...]

179 If Something Goes Wrong Resolving a har dwar e conflict T ry printing another file. For exam ple, you could create and attempt to print a short test file using Notepad. If a Notepad file prints correctly , the problem may be in yo ur original f ile. If you cannot resolve the problem, contact the printer’ s manufacturer . The printer will not [...]

180 If Something Goes Wrong Resolving a hardwar e conflict Wireless networking problems This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi ® ) networking. The terms and concepts used assume a bas ic understanding of networks, and may be for more advanced users. If you need assistance or if you [...]

181 If Something Goes Wrong Resolving a har dwar e conflict 3 Click Details . 4 V erify that the DHCP E nabled setting is set to Ye s . 5 Click Close . ❖ Use IPCONFIG to verify that the computer has a useful IP address—one other th an the priv ate address of 169.254.xxx.xxx assi gned by W indo ws ® . 1 Click Start to open the Start menu. 2 T y[...]

182 If Something Goes Wrong D VD operating pr oblems Special considerations for the Windows ® operating system Wir ed Equi valent Priv acy (WEP) encryption is not enabled on the wireless access point. When you install a wireless access point de vice, the W indo ws ® operating system checks whether WE P encry ption is enabled on the device. If it [...]

183 If Something Goes Wrong D VD operating pr oblems 4 Clean the disc and try again. A dirty dri ve can also cause audio problems. If you hav e tried se veral discs and all fail, consider sen ding your driv e to an authorized service provid er to get it cleaned. 5 V erify that your computer recognizes your op tical dri ve b y clicking Start , and t[...]

184 If Something Goes Wrong Develop good computing habits Develop good computing habits Sa ve y our work fr equently . Y ou can ne ver predict when your co mputer will lock, forcin g you to close a program and lose unsaved changes. Man y software programs build in an automatic backup, but you should not rely solely on this feature. Save your work! [...]

185 If Something Goes Wrong Develop good computing habits Data and system configuration backup in the Windows ® operating system The W indo ws ® operating system offers some easy-to-use features for backing up your Windo ws ® settings and your data—documents and other important files. T ake advantage of these features to protect yourself from [...]

186 If Something Goes Wrong Develop good computing habits Then, at a later time, you can re-establish your Windo ws ® configuration using the saved Restore Point. T o do this: 1 Click Start , All Programs , Acces sories , System T ools , and then System Restore . 2 Click Next . 3 A list of previously created Restore Points displays, showing the ti[...]

187 If Something Goes Wrong Develop good computing habits Follo w these steps to back up your computer or f iles to CDs, D VDs, or a hard driv e: Y ou can not back up the computer while running on battery power . Connect the AC adaptor before continuing. 1 Prepare your backup tar get by c onnecting it and/or inser ting a blank CD or D VD in the dri[...]

188 If Something Goes Wrong Develop good computing habits ❖ Hav e your factory Restore/Reconfiguration CD(s) on hand in case you need any f iles from them (av ailable on certain models). ❖ Do not guess—follow directions carefully! It is often necessary to run an installation utility first—before connecting a new hardware item to the compute[...]

189 If Something Goes Wrong If you need further assistance If you need further assistance If you have follo wed the recomm endations in this chapter and are still having problems, you may n eed additional technical assistance. This section contains the step s to take to ask for help. Before you contact T oshiba Since some problems m ay be related t[...]

190 If Something Goes Wrong Other T oshiba Internet W eb sites ❖ Backup copies of your W indows ® operating system and all other preloaded software on your choice of media ❖ Name and version of the program in volv ed in the problem along with its i nstallation media ❖ Information about what you were doing w hen the problem occurred ❖ Exact[...]

191 If Something Goes Wrong T oshiba’ s worldwide of fices For more information on additional T osh iba worldwide locations, please visit: www .toshi ba.co.jp/ index. htm . Italy Centro Direzionale Colleoni Palazzo Perseo Vi a P a r a c e l s o 1 0 20041, Agrate Brianza Milano, Italy Jap an T oshiba Corporation, PCO- IO 1-1, Shibaura 1-Chome Mina[...]

192 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards prov ide a quick way to modif y selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot K ey Cards and Application Cards. Hot Key Cards The Hot Ke y Cards are used to modify the following system functions: ❖ Mute ❖[...]

193 Hot Keys /TOSHIBA Cards Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear only when the pointing device is mo ved to the top center edge of the screen. In addition, a Hot Ke y Card can be displayed b y pressing the associated hot key . Hot keys are keys that, when [...]

194 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIB A Assist For more infor mation, refer to “TOSHIB A Assist” on page 137 . PC Diagnostic T ool utility For more inform ation, refer to “TOSHIB A [...]

195 Hot Keys /TOSHIBA Cards Application Cards 5.375 x 8.375 ver 2.3 Using the Application Cards T o launch an application using the Application Cards: 1 Mov e the cursor to the top center edge of the screen. The TOSHIB A Cards display at the top of the screen. (Sample Image) T OSHIBA Car d display 2 Click the “stacked” card on the far right of [...]

196 Hot Keys/TOSHIBA Cards Hot ke y funct ions 5.375 x 8.375 ver 2.3 3 The Card Case displays tw o rows of Cards. Cards that appear solid (not tr ansparent) in the bottom ro w are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards . (Sample Image) Enabling and Disabling Application C[...]

197 Hot Keys /TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Volume Mute or Fn + This TOSHIB A Card or hot ke y enables/disables volume mute on your computer . When volume mute is enabled, n o sound will come fro m the speakers or headphones. Selecting this Card or pressing the hot ke y displays the following options: (Sample Image) V olu m[...]

198 Hot Keys/TOSHIBA Cards Hot ke y funct ions 5.375 x 8.375 ver 2.3 Password security The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a us er with a valid account will need to log back on to gain access to the computer . or Fn + This TOSHIB A Card or hot ke y blanks the display . Selecting this Car[...]

199 Hot Keys /TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window . Selecting this Card or pressing the ho[...]

200 Hot Keys/TOSHIBA Cards Hot ke y funct ions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep mode” on page 78 . Selecting this Card or pressing the hot key displays the following options: (Sample Imag e)[...]

201 Hot Keys /TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernatio n mode” on page 75 . Selecting t[...]

202 Hot Keys/TOSHIBA Cards Hot ke y funct ions 5.375 x 8.375 ver 2.3 Display modes or Fn + This TOSHIB A Card or hot ke y cycles through the power - on display options . Some modes are only available with the appropriate device attached and turned on. The displa y modes are: ❖ Built-in display only ❖ Built-in display and external monitor simult[...]

203 Hot Keys /TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness This TOSHIB A Card decreases or increases the screen brightness. Fn + This hot key de creases the screen brightness. Fn + This hot k ey increases the s creen brightness. Selecting this Card or pressing either hot key displays the following options: (Sample Image[...]

204 Hot Keys/TOSHIBA Cards Hot ke y funct ions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless mode is: ❖ Wi - F i ® enabled—Enables the W i-Fi ® module. Selecting this Card or pressing the hot key disp[...]

205 Hot Keys /TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad or Fn + This TOSHIB A Card or hot key enables/disables the T o uchPad. For more information on using the T ouchPad, see “Disabling or enabling the T ouchPad™” on page 65 . Selecting this Card or pressing the hot ke y displays the following[...]

206 Hot Keys/TOSHIBA Cards Hot ke y funct ions 5.375 x 8.375 ver 2.3 Changing screen resolution or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Scr een r esolution options Cycle through the screen resolu tions, then select the [...]

207 Hot Keys /TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot ke y turns the curs or control ov erlay on and off. Fn + This hot ke y turns the numeric overlay on and of f. Fn + This hot ke y turns the scroll lock featu re on and of f. Fn + This hot ke y tu rns the Z o om in g utility to zoom-out. Fn +[...]

208 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our notebook computer features a universal po wer supply you can use worldwide. This appendix show s the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world. USA and Canada UL ap prove d CS A ap pr oved United Kingdom BS ap prove d Australia [...]

209 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide. AC alternating current BIOS basic input/output system bps bits per second CD compact disc CD-R OM compact disc read-only memory CD-R W compact disc rewrite memory CMOS com[...]

210 Glossary DOS disk operating system DPI dots per inch DSTN dual supertwist nem atic DV D digital versatile (or video) disc DV D - RO M dig ital versatile (or video) disc read-only memory ECP enhanced cap abilities port EPR OM erasable programmable read-only memory FAT f ile allocation table FCC Federal Communicat ions Commission GB gigabyte HDD [...]

Glossary 211 SDRAM synchronous dynamic random access memory SRAM static random access memory SVGA super video graphics adapter TFT thin film transistor USB univ ersal serial b us URL uniform resource lo cator WA N wide area netw ork www W orld W ide W eb Te r m s The follo wing terms may appear in this user’ s guide. A active-matrix display — A[...]

212 Glossary baud rate — The speed at which a comm unication de vice, such as a printer or modem , transmits inform ation. Baud rate is th e number of signal changes per second (not necessarily the sam e as bits per second). See also bits per second . BIOS (basic input/ output system) — Basic instructions, stored in read- only memory (R OM), co[...]

Glossary 213 central processing unit (CPU) — The chip that functions as the “brain” of the computer . It takes informa tion from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character — Any letter , number , or symbol you can use on the compu[...]

214 Glossary device — A component attached to the computer . Devices may be external (outside the computer’ s case) or internal (inside the computer’ s case). Printers, disk dr i ves, and modems are examples of devices. device driv er — A program (called a “dri ve r”) that permits a computer to communicate with a device. dialog box — [...]

Glossary 215 double-density d iskette — A 3.5-inch diskette that can hold up to 720 KB of information (half the capac ity of a high-density diskette). See also diskette, high-density diskette. download — (1) In communications, to recei ve a f ile from another computer through a modem or network. (2) T o send font data from the computer to a pri[...]

216 Glossary f ile extension — The three characters foll o wing the period (pronounced “dot”) at the end of a f ile name. The extension indicates the type of file. Examples are .ex e for program files and .hlp for help fi les. See also file name . fo ld e r — Also called directory . A container for organizing files sa ved to a disk. A folde[...]

Glossary 217 hot key — (1) A feature in which cert ain ke ys in combination with the Fn key can s et system options or control system parameters, such as the batter y sav e mode. (2 ) A ke y or combina tion of k eys th at acti vates a memory resident program. hot swapping — The ability to add or remov e devices from a computer while the compute[...]

218 Glossary local area network — See LAN. logical drive — A section of a disk that is recognized by the operating system as a separate disk dri ve. A system’ s logical dri ves may dif fer from its physical dri ves. F or example, a single hard disk dri ve may be partitioned in to two or more logical drives. M memory — T ypically refers to t[...]

Glossary 219 non-system disk — A disk for storin g programs and data that cannot be used to start the computer . Compare system disk . O online — A vailable through the computer . Online may refer to information being read from your own computer’ s hard disk, such as online documentation or online Help, or to info rmation coming from another [...]

220 Glossary port — A socket on the computer where you plug in a cable for connection to a network or a peripheral device. processor — See central pr ocessing unit (CPU) . program — A set of instructions that can be exe cuted by a computer . The general classes of programs (also called software) are operating system, application, an d utility[...]

Glossary 221 S select — T o hig hlight or otherwise specify text, data, or graphics with the intent to perform some operation on it. serial — Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentia lly ov er a single channel. On your computer , the seri al port provides a serial interf ace[...]

222 Glossary W We b — See W orld W ide W eb . Wi- F i ® — A re gistered trademark term of the W i-Fi Alliance that stands for W ireless Fidelity , and is anot her term for the communication protocol to permit an Ethernet connect ion using wireless communication components. W orld Wide W eb (w ww) — The worldwide network of W e b sites linked[...]

223 Index A A C adaptor 43 AC p o w e r connecting adaptor 44 accessories memory 48 adding memory 48 Alt ke ys 86 Application Card Using 195 Application Cards 194 audio fil e s 128 audio features 128 B backing up files 84 battery changing 111 charge indicator light 45 , 105 charge not lasting 168 charging 43 , 45 conserving power 108 disposal 116 l[...]

224 Index communications network connection 123 set up 121 compact disc positioning 96 compact discs handling 96 inserting 95 removing 99 compact disk dri ve using 93 computer caring for 81 cleaning 81 moving 81 non-system disk or disk error message 161 not accessing disk driv es 160 running on battery power 101 setting up 41 , 49 warning resume fa[...]

225 Index ExpressCard checklist 176 computer stops working 177 errors 178 hot swapping fails 177 not recognized 178 problem solving 176 , 177 ExpressCard™ inserting 132 removing 132 ext er na l monitor not working 170 mouse 67 external diskette driv e connecting 69 external display , adj usting 67 F F A T (File Allocation T able) 171 file extensi[...]

226 Index K keyboard character keys 85 function keys 86 hot keys 207 not working 160 ov erlay keys 87 special W indo ws® keys 86 troubleshooting 168 using 85 keyboard, e xternal 67 keyboard, full-size 85 L lock computer , using 82 M main battery removing 111 memory adding 48 problem solving 166 removing expansion slot cov er 50 memory module inser[...]

227 Index computer will not start 159 connecting cable to A C adaptor 44 cord/cable connectors 208 energy-sa ving features 101 problem solving 167 turning on 47 power b utton 48 , 57 po wer plan hot key 110 power plans 109 power source 43 connecting 44 po wering do wn using Hibernation 75 using Shut Dow n 73 using Sleep 78 precautions 39 primary bu[...]

228 Index not running correctly 172 projector 65 connecting 66 R real-time clock (R TC) battery 102 recording sounds 128 recording sounds 128 recycle bin icon 119 registering computer 42 removing main battery 111 RJ-11 jack 123 running the computer on battery power 101 S safety computer 11 7 disposing of batteries 116 icons 36 precautions 39 saving[...]

229 Index V video projector adjusting display 67 W war ran ty limited warranty 37 We b 126 We b C a m 129 We b s i t e s 189 Wi - F i ® wireless netw orking 125 W indo ws Media® Player 97 W indo ws® Explorer 89 W indows® operating system Help and Support 164 problem solving 162 W indo ws® operating syst em desktop 118 W indo ws® Start menu 88[...]