Français dropdown-ico

Toshiba MMK-AP0072H manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Toshiba MMK-AP0072H. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Toshiba MMK-AP0072H ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Toshiba MMK-AP0072H décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Toshiba MMK-AP0072H devrait contenir:
- informations sur les caractéristiques techniques du dispositif Toshiba MMK-AP0072H
- nom du fabricant et année de fabrication Toshiba MMK-AP0072H
- instructions d'utilisation, de réglage et d’entretien de l'équipement Toshiba MMK-AP0072H
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Toshiba MMK-AP0072H ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Toshiba MMK-AP0072H et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Toshiba en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Toshiba MMK-AP0072H, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Toshiba MMK-AP0072H, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Toshiba MMK-AP0072H. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Indoor Unit Unité intérieure Raumeinheit Unità interna Unidad interior Unidade interior Binnen unit ÅóùôåñéêÞ mïíÜäá <High-W all T ype> <T ype mural haut> <W and modell> <Tipo per mura alte> <Tipo par te alta de la pared> <Tipo para P arede Alta> <Hogew andmodel> <Ôýðïò ôïðïèå[...]

  • Page 2

    ADOPTION OF NEW REFRIGERANT This Air Conditioner is a new type which adopts a ne w refrigerant HFC (R410A) instead of the conventional refrigerant R22 in order to prev ent destr uction of the ozone la yer . UTILISA TION DU NOUVEA U REFRIGERANT Ce climatiseur est d ’ un type in é dit qui utilise le nouveau r é frig é rant HFC (R410A) au lieu du[...]

  • Page 3

    CONTENTS SOMMAIRE INHALT INDICE CONTENIDO Í NDICE ÐÅÑÉÅ×ÏÌÅÍÁ INHOUD ITALIANO ESPA Ñ OL PORTUGU Ê S ÅËËÇÍÉÊÁ FRANCAIS DEUTSCH NEDERLANDS ENGLISH Accessory par ts and parts to be procured locall y ....................................... 1 1 PRECA UTIONS FOR SAFETY ............................................................... [...]

  • Page 4

    1 Accessory parts and parts to be procured locally H Accessory parts H Parts to be procured locally Connecting pipe (Liquid side) (6.4mm (diam.), Nominal (diam.) 1/4” thick 0.8mm) MMK-AP0072H to MMK-AP0122H Connecting pipe (Gas side) (9.5mm (diam.), Nominal (diam.) 3/8” thick 0.8mm) MMK-AP0072H to MMK-AP0122H Power supply cord Cable 3-core 2.5m[...]

  • Page 5

    2 1 PRECAUTIONS FOR SAFETY • Ensure that all Local, National and International regulations are satisfied. • Read this “ PRECAUTIONS FOR SAFETY ” carefully before Installation. • The precautions described below include the important items regarding safety. Observe them without fail. • After the installation work, perform a trial operatio[...]

  • Page 6

    3 • Install the air conditioner securely in a location where the base can sustain the weight adequately. • Perform the specified installation work to guard against an earthquake. If the air conditioner is not installed appropriately, accidents may occur due to the falling unit. • If refrigerant gas has leaked during the installation work, ven[...]

  • Page 7

    4 Installation space Reserve space required to install the indoor unit and for service work. Keep 100mm or more for clearance between top plate of the indoor unit and the ceiling surface. Installation diagram of Indoor and outdoor units The auxiliary piping can be connected the left, rear left, rear right, right, bottom right or bottom left. Before[...]

  • Page 8

    5 3 INSTALLATION OF INDOOR UNIT WARNING Install the air conditioner certainly to sufficiently withstand the weight. If the strength is insufficient, the unit may fall down resulting in human injury. Perform a specified installation work to guard against strong wind or earthquake. An incomplete installation can cause accidents by the units falling a[...]

  • Page 9

    6 4 CUTTING A HOLE AND MOUNTING INSTALLATION PLATE When the installation plate is directly mounted on the wall 65 mm 100 mm The center of the pipe hole is above the arrow. Pipe hole Cutting a hole In case of installing the refrigerant pipes from the rear: 1. Decide the hole position for piping at 100mm from the arrow mark ( ) on the installation pl[...]

  • Page 10

    7 5 PIPING AND DRAIN HOSE INSTALLATION Piping and drain hose forming * Apply thermal-insulation for both refrigerant pipe and drain hose surely so that no dewing generates inside of the equipment. (Use polyethylene foam for insulating material.) Heat insulator Drain hose 4 mm Do not apply lubricating oil (refrigerant machine oil) when inserting the[...]

  • Page 11

    8 In case of right or left piping • After scribing slits of the front panel with a knife or a marking-off pin, cut them with a pair of nippers or an equivalent tool. In case of bottom right or bottom left piping • After scribing slits of the front panel with a knife or a marking- off pin, cut them with a pair of nippers or an equivalent tool. L[...]

  • Page 12

    9 6 INDOOR UNIT FIXING 7 DRAINAGE 1. Pass the pipe through the hole in the wall, and hook the indoor unit on the installation plate at the upper hooks. 2. Swing the indoor unit to right and left to confirm that it is firmly hooked up on the installation plate. 3. While pressing the indoor unit onto the wall, hook it at the lower part on the install[...]

  • Page 13

    10 8 REFRIGERANT PIPING WARNING • If refrigerant gas has leaked during the installation work, ventilate the room immediately. • If the leaked refrigerant gas comes in contact with fire, noxious gas may generate. • After the installation work, confirm that refrigerant gas does not leak. • If refrigerant gas leaks into the room and flows near[...]

  • Page 14

    11 • Projection margin in flaring : B (Unit : mm) Rigid (Clutch type) Imperial (Wing nut type) Connection of refrigerant pipe Connect all the refrigerant pipes with flare connecting work. • Since the atmospheric pressure only is sealed as the sealing gas, it is not abnormal that “ Pushu …” sound is not heard when the flare nut is removed.[...]

  • Page 15

    12 9 ELECTRIC WORK WARNING 1. Using the specified wires, ensure to connect the wires, and fix wires securely so that the external strength of the wires do not transmit to the connecting part of the terminals. Incomplete connection or fixation may cause a fire, etc. 2. Be sure to connect earth wire. (Grounding work) Do not connect the earth wire to [...]

  • Page 16

    13 Indoor unit po wer supply (*1) • For the power supply of the indoor unit, p repare the exclusive power supply separated from that of the outdoor unit. • Arrange the power supply, earth leakage breaker, and main switch of the indoor unit connected to the same outdoor unit so that they are commonly used. • Power supply cord specification : C[...]

  • Page 17

    14 N L 110mm 10mm 40mm 10mm U1 N L U2 A B U1 N LU 2 A B R(L) S(N) > ABS < Cord clamp Cord clamp Remote controller cable P ower supply cable Screw Connector co ver T er minal block Notch • Tighten the screws of the terminal block, and fix the cables with cord clamp attached to the electric parts box. (Do not apply tension to the connecting s[...]

  • Page 18

    15 Remote controller wiring • Strip off approx. 14mm cover of the wire to be connected. • Twist wire of the remote controller to be connected with wire of the remote controller unit (or sensor), and press-fit them with a wire joint. (Wire joints (White: 2 pieces) are included in the accessory of the main remote controller (sold separately) or w[...]

  • Page 19

    16 10 APPLICABLE CONTROLS NOTIFICATION When using the equipment at the first time, it will take a lot of time that the remote controller accepts an operation after power was on. However, it is not a trouble. • Automatic address • While automatic addressing, the operation cannot be performed on the remote controller. • For automatic addressing[...]

  • Page 20

    17 Change of lighting time of filter sign According to the installation condition, the lighting time of the filter sign (Notification of filter cleaning) can be changed. Follow to the basic operation procedure ( 1 → 2 → 3 → 4 → 5 → 6 ). • For the item code in Procedure 3 , specify [01]. • For the [Set data] in Procedure 4 , select the[...]

  • Page 21

    18 NOTE Do not use a forced operation in cases other than test operation because it applies an excessive load to the air conditioner. In case of wired remote contr oller Procedure 1 2 3 4 5 Description Keep button pushed for 4 seconds or more. [TEST] is displayed on the display part and the selection of mode in the test mode is permitted. Push butt[...]

  • Page 22

    19 In case of wireless remote contr oller (For ced test operation is perf ormed in a different wa y .) REQUIREMENT 1. For the operation procedure, be sure to follow the Owner ’ s Manual. 2. Finish the forced cooling operation in a short time because it applies excessive strength to the air conditioner. 3. A test operation of forced heating is una[...]

  • Page 23

    20 12 TROUBLESHOOTING Confirmation and check When a trouble occurred in the air conditioner, the check code and the indoor unit No. appear on the display part of the remote controller. The check code is only displayed during the operation. If the display disappears, operate the air conditioner according to the following “ Confirmation of error hi[...]

  • Page 24

    21 Check method On the remote controller (Main remote controller, Central control remote controller) and the interface P.C. board of the outdoor unit (I/F), a check display LCD (Remote controller) or 7-segment display (on the outdoor interface P.C. board) to display the operation is provided. Therefore the operation status can be known. Using this [...]

  • Page 25

    22 Check code Main remote controller display F01 F02 F03 F04 F05 F06 F07 F08 F10 F12 F13 F15 F16 F23 F24 F29 F31 H01 H02 H03 H04 H06 H07 H08 H14 H16 L03 L04 L05 L06 L07 L08 L09 L10 L20 L28 L29 L30 — Outdoor 7-segment display Auxiliary code —— —— —— F04 — F05 — F06 — F07 — F08 — —— F12 — F13 01: Comp. 1 side 02: Comp. 2[...]

  • Page 26

    23 Check code Main remote controller display P01 P03 P04 P05 P07 P10 P12 P13 P15 P17 P19 P20 P22 P26 P29 P31 — Outdoor 7-segment display Auxiliary code —— P03 — P04 01: Comp. 1 side 02: Comp. 2 side P05 01: Phase-missing detection 02: Phase error P07 01: Comp. 1 side 02: Comp. 2 side P10 Detected indoor address —— P13 — P15 01: TS con[...]

  • Page 27

    24 New check code 1. Difference between the new check code and the current system The displaying method of the check code changes in this model and after. <Display on wired remote controller> • [ ] goes on. • [UNIT No.] + Check code + Operation lamp (Green) flash <Display on sensor part of wireless> • Block display of combination [...]

  • Page 28

    W ARNINGS ON REFRIGERANT LEAKA GE For the amount of charge in this example: The possible amount of leaked refrigerant gas in rooms A, B and C is 10kg. The possible amount of leaked refrigerant gas in rooms D, E and F is 15kg. NOTE 2 : The standards for minimum room volume are as follows. (1) No partition (shaded portion) (2) When there is an effect[...]

  • Page 29

    1108150101 CONFIRMATION OF INDOOR UNIT SETUP Prior to deliver y to the customers, chec k the address and setup of the indoor unit, which has been installed in this time and fill the chec k sheet (T able below). Deta of four units can be entered in this chec k sheet. Copy this sheet according to the No . of the indoor units. If the installed system [...]