Toshiba PSAG8U-02E018 manuel d'utilisation

GMAD00161011 04/08 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Global Support Centre Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 166 in this gui de. Satellite ® A300 Series [...]

2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling . Model: Satellite ® A300 Series Recordable and/or ReWritable Drive(s) and Associated Software W arranty The computer system you purchased may in[...]

3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical applications, connections to implanted medi cal devi ces, commercial transportation, nuclear facilities or systems or an y other applicatio ns where pro[...]

4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n. Contact either: ❖ T oshiba’ s Support W eb si[...]

5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can. In order to do this, it may occas[...]

6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable yo ur alarm equipment. If you hav e questions abou t what will disable alarm equipment, consult your telephone compan y or a qualified installer . Instructions for IC CS[...]

7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology , and is compliant to: ❖ The IEEE 802.11 Standard on W ireless LANs (Rev ision A/B/G), as defined and approv ed [...]

8 5.375 x 8.375 ver 2.3 In some situations or en vironments, the use of W ireless LAN may be restricted by the proprietor of the b uilding or responsible representativ es of the organization. These situatio ns may for e xample include: ❖ Using the W ireless LAN equipment on board airplanes, or ❖ In any other en vironment where the risk of inter[...]

9 5.375 x 8.375 ver 2.3 The term “IC” before the equipment certif ication number only signifies that the Industry Canada technical specifications were met. T o prev ent radio interference to the licensed service, this device is intended to be operated indoors an d away from windo ws to pr ovide maximum shielding. Equipment (or its transmit ante[...]

10 5.375 x 8.375 ver 2.3 The European Union WEEE (W as te from Electrical and Electronic Equipment) Directive Information The European Union WEEE (W aste from Electrical and Electronic Equipment) Directiv e is intended to protect the quality of the en vironment and human health through the responsible use of n atura l resources and the adoption of [...]

11 5.375 x 8.375 ver 2.3 Modem W arning Notice Conformity Statement The equipment has been ap prov ed to [Commission D ecision “CTR21”] for pan- European single terminal connection to the Public Switched T elephone Network (PSTN). Howe ver , due to dif ferences between the indi vidual PSTNs provided in dif ferent countries/re gions the approv a[...]

12 5.375 x 8.375 ver 2.3 1. Sticker Please put the following stick er on devices incorpora ting this product. 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. O F: This equipment uses OFDM modulation. 3 The interference range of this e[...]

13 5.375 x 8.375 ver 2.3 J AP AN APPR O V ALS INSTITU TE FOR TELECOMMUNICA TIONS EQUIPMENT Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Ap proval Number: 03NY .A0018, 03GZD A0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wire less module into other device. ❖ 5.17 GHz t[...]

14 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries Luxembour g Malta Mexico Netherlands New Zealand Norway Pakistan Peru Philippines Poland Portugal Romania Russia Saudi Arabia Slo vakia Slov enia South Korea Spain Sweden Switzerland/ Liechtenstein Ta i w a n ( R O C ) U AE (United Arab Em[...]

15 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply . The user should use the wireless LAN utility to check the current cha[...]

16 5.375 x 8.375 ver 2.3 radar system in the area. The presence of nearby radar operation may result in temporary interruption of operation of this device. The Access Point’ s radar detection feature will automatically restart operation on a channel free of radar . Y ou may consult with the local te chnical support staff responsible for the wirel[...]

17 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Intel ® PRO/ Wireless LAN 2100 3B Mini PCI Adapter This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Approved Countries/Regions for the Realtek ® RTL[...]

18 5.375 x 8.375 ver 2.3 Ecuador Egypt El Salvador Estonia Finland France Germany Ghana Greece Guatemala Honduras Hong K ong Hungary Iceland India Indonesia Ireland Israel Italy Japan - Jate Japan - T eleco Jordan Kazakhstan K enya Kuwait Latvia Lebanon Lesotho Liechtenstein Lithuania Luxembour g Macedonia Malaysia Malta Mexico Monaco Morocco Nethe[...]

19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Intel ® PRO/Wireless 3945ABG Network Connection This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g)[...]

20 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g), An Infrastructu[...]

21 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio t echnology , and is compliant to: ❖ Bluetooth Specification as def ined and approv ed b[...]

22 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table. Bluetooth ® Wireless T echnology and Y our[...]

23 5.375 x 8.375 ver 2.3 In some situatio ns or en vironments, the use of Bluetooth wireless technology may be restricted by the proprietor of th e building or responsible representati ves of the organization. These situations may for example include: ❖ Using the equipment with Bluetooth wireless technology on boar d airplanes, or ❖ In any othe[...]

24 5.375 x 8.375 ver 2.3 Ta i w a n The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations. Lo w power radio frequency electric machinery shall resist against interference from legal communications or from indu strial, scientific and medical radio emiss[...]

25 5.375 x 8.375 ver 2.3 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to av o[...]

26 5.375 x 8.375 ver 2.3 Optical Drive Safety Instructions This appliance contains a laser syst em and is classified as a CLASS 1 LASER PRODUCT . T o use this model properl y , read th e user’ s guide carefully and keep it for your fut ure reference. Never attempt to disass emble, adjust or repair an opti cal drive. Y ou could damage the drive. Y[...]

27 5.375 x 8.375 ver 2.3 Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and ma y be subject to the approv al of the U.S. Department of Commerce prior to export. Any export, directly or indirectly , in contrav ention of the U.S. Export Ad ministration Re[...]

28 5.375 x 8.375 ver 2.3 T rademarks Satellite and ConfigFree are re gistered trademarks of T oshiba Ameri ca Information Systems, Inc. and/or T oshiba Corporation. Microsoft, Outlook, Windo ws, and Wi ndo ws V ista are either registered trademarks or trademarks of Microsoft Corporatio n in the United States and/or other countries. DirectX, Activ e[...]

29 5.375 x 8.375 v er 2.3 Contents Introduction ................................................................................ 36 This guide ...............................................................38 Safety icons ............................................................39 Other icons used ...............................................3[...]

30 Contents 5.375 x 8.375 v er 2.3 Using the computer fo r the first time ......................50 Opening the display panel ................................. 50 Your computer’s features and specifications ....51 Turning on the power .......................................51 Adding memory (optional) ......................................52 Instal[...]

31 Contents 5.375 x 8.375 v er 2.3 Moving the computer ........................................ 86 Using a computer lock ......................................86 Chapter 2: Learning the Ba sics ................................................. 87 Computing tips ....................................................... 87 Using the keyboard ..........[...]

32 Contents 5.375 x 8.375 v er 2.3 Chapter 3: Mobile Comput ing................................................. 104 Toshiba’s energy-saver design..............................104 Running the computer on battery power ..............105 Battery Notice ................................................. 105 Power management ..........................[...]

33 Contents 5.375 x 8.375 v er 2.3 Surfing the Internet .........................................129 Internet features ..............................................129 Uploading to, and downloading files from, the Internet .....................................130 Exploring audio features .......................................130 Recording sounds [...]

34 Contents 5.375 x 8.375 v er 2.3 TOSHIBA Accessibility .......................................... 158 Fingerprint Authentication Utility ...........................159 Fingerprint utility limitations ...........................159 Using the Fingerprint Authentication Utility .....159 Fingerprint Logon ...........................................16[...]

35 Contents 5.375 x 8.375 v er 2.3 Data and system configuration backup in the Windows ® operating system ...............190 If you need further assistance ............................... 194 Before you contact Toshiba ............................194 Contacting Toshiba .........................................195 Other Toshiba Intern et Web sites [...]

36 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go. Y our Computer model may be ENERGY ST AR ® compliant. If the model you purchased is compliant, it is labeled with the ENER GY ST AR ® log o on the computer and the [...]

37 Introduction 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 20% and 50% less energ y depending on how it is used. If all U.S. household and businesses replaced old computers with ne w ENERGY ST AR ® qualified models, we would sav e more than $1.8 billion in energy costs ov[...]

38 Introd uctio n This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit T osh[...]

39 Introduction Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipmen t, or loss of data. These safety cautions hav e been classif ied according to the seriousness of the risk, and icons highlight th[...]

40 Introd uctio n Other documentation 5.375 x 8.375 ver 2.3 Other documentation Y our computer comes with the following documentation: ❖ An electronic version of the user’ s guide (this docum ent) ❖ It may also contain guides for other programs that may come with your system. For accessory information, visit T oshiba’ s W eb site at accesso[...]

41 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information. Please read the safet[...]

42 Getting Started Selecting a place to work T o keep your computer in prime operating condition, protect you r work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in[...]

43 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin. Read the “ A void e xtended contact between computer base/palm rest and skin” section in the “Instruction Ma[...]

44 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that coo ls the CPU by drawing outside air into the computer . Always mak e sure your compute r and AC adapt or have adequate ventilation and are protected from overheating when the power is turne d on or whe[...]

45 Getting Started Setting up your computer Please handle your computer carefully to avoi d scratching or damaging the surface. Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely . The names of windows dis played, and th e order in which windows[...]

46 Getting Started Re gistering your computer with T oshiba Registering your computer with T oshiba Product registration is strongly recommended , and allo ws T oshiba to send you periodic updates, announcement s, and special offers applicable to your p roduct. Product registration can be compl eted during the initial start up process of your compu[...]

47 Getting Started Connecting to a po wer sour ce Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery . Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug dire[...]

48 Getting Started Connecting to a power so ur ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord/cable to the A C adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other [...]

49 Getting Started Char ging the main battery The computer’ s main battery light gives you an indication of the main battery’ s current char ge: ❖ Glows amber while the main battery is bei ng charged (A C adaptor connected) ❖ Glows white or green, depending on your model, when the main battery is fully charged ❖ Is unlit when t he main ba[...]

50 Getting Started Using the computer for the fir st time Battery life and charge time may var y depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and be gin using it. Opening the display panel 1 Facing the front of the com puter, locate[...]

51 Getting Started Using the computer for the f irst time Small bright dots ma y appear on your screen display wh en you turn on your computer . Y our disp lay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology . An y small bright dots that may appear on your display are an intrins[...]

52 Getting Started Adding memory (optional) 3 Press and release the po wer b utton. The on/off light glows white or green, depending on your model. (Sample Illustration) T urning on the power The preinstalled operating syst em will load automatically . When you turn on the computer for the first time, do not turn off the power again until the opera[...]

53 Getting Started Adding memory (optional) Installing a memory module Memory modules can be installed in the memor y module slots on the base of the computer . Y ou will need a small Phillips scr e wdriver for this procedure. If the computer has been running recently , the memor y module may be hot. The surrounding area may also be hot. Allow the [...]

54 Getting Started Adding memory (optional) If the computer is on, begin at step 1 ; otherwise, skip t o step 3 . 1 Click Start , and then click the arrow ne xt to the lock button in the lower -right corner of the Start men u. The Shut Down menu appears. (Sample Image) Shut Down menu 2 Click Shut Down . The operating system turns off the computer .[...]

55 Getting Started Adding memory (optional) 6 Using a small Phillips screwdri ver , loosen the capti ve scre w that secures the memory module slot cover . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cover . 8 Place the screw and the cov er in a safe place so that you can retriev e them later . Static [...]

56 Getting Started Adding memory (optional) If your system has the memory modules stacked on top of one another , you must remove the top module first before removing/installing the bottom module. For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in slot A. 11 Pick u[...]

57 Getting Started Adding memory (optional) 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on the top edge of the module to seat the module into the latches at the sides of the so cket. These latches should “snap” into place securely with th e corresponding cutouts in the side of the module. If the latches[...]

58 Getting Started Adding memory (optional) 15 Re-insert the main battery . For more information on i nserting the main battery , see “Inserting a char ged battery” on page 117 . 16 T urn the computer right side up. 17 Reconnect the cables. 18 Restart the computer . TECHNICAL NOTE: Y ou must have at least one memor y module installed for the co[...]

59 Getting Started Adding memory (optional) The following screen may appear when you turn on the power: If “Start Windows ® Normally” is highlighted, then press Enter . If one of the Safe Mode options is highlighted, it is best to press Enter to go into Safe Mode, then shut down and restart the system, at which time Windows ® should boot back[...]

60 Getting Started Adding memory (optional) 4 Replace the memory modu le slot cov er and secure it using the screw . 5 Re-insert the main battery . For more information on i nserting the main battery , see “Inserting a char ged battery” on page 117 . 6 T urn the computer right side up. 7 Reconnect the cables. 8 Restart the computer . TECHNICAL [...]

61 Getting Started Har d Drive Recovery Utilities Hard Drive Recovery Utilities (A vailable on certain models) Y our computer has been configured with a hard disk partitio n to allow you to recov er your hard di sk drive or reinstall selected applications and software features or utilities. It is strongly recommended that y ou create recover y DVDs[...]

62 Getting Started Har d Drive Recovery Utilities T o create recov ery D VDs: 1 Double-click the Recovery Disc Cr eator icon on the W indows ® desktop. Y ou can also launch the application by clicking Start , All Programs , and then Recovery Disc Creator . 2 Select DV D (to create Recovery media on D VDs). 3 Select the items you want to copy by cl[...]

63 Getting Started Har d Drive Recovery Utilities Hard Disk Drive Recovery using the recover y partition Y ou hav e the options of recov ering your system using the Hard Driv e Recov ery partition to the factory-set default, or recovering just your C: drive and leaving other partitions (for example, a D: dri ve) intact, or changing the size of your[...]

64 Getting Started Har d Drive Recovery Utilities Recovering the original factory image (recommended recovery method) Recovering a hard disk drive to its out of box state deletes all parti tions on the hard disk drive and you r information will be lost. Be sure to save your work to external media first. 1 On the T oshiba Recovery W izard screen, se[...]

65 Getting Started Har d Drive Recovery Utilities Erasing the hard disk The Recov ery W izard allows you to delete all data and partitions from the hard di sk. T o delete the data and partitions from your hard disk: 1 On the T oshiba Recovery W izard screen, select Erase the hard disk , and then click Next . 2 The next screen lists the two methods [...]

66 Getting Started Har d Drive Recovery Utilities Recovering the C: partition of the HDD without changing the current partition size Recovering the C: drive to its factory default setting reformats your drive and your information on the recovered drive will be lost. Be sure to save your work to external media first. If you have created other partit[...]

67 Getting Started Har d Drive Recovery Utilities 4 Click Next to begin the restoration. Once complete, a message displays that the HDD has been recov ered. 5 Press any ke y on your keyboard to restart the computer . Hard Disk Drive Recovery using the Recover y media If you need to recover your computer to its default factory state, you can rebuild[...]

68 Getting Started Using the T ouchP ad™ 3 Select Manage . 4 Click Disk Manageme nt . 5 Highlight the hard disk dri ve in the V olume list to displ ay its status in the lower portion of the screen. Installing drivers and applications (A vailable on certain models) The T oshiba Application Installer (av ailable on cert ain models) allo ws you to r[...]

69 Getting Started Using external display de vices Once you hav e positioned your cursor , you can click it into place b y either double-tapping the T ouch Pad or clicking the control buttons. Scrolling with the T ouchPad ™ There are two acti ve regions on the T ouchPad ™ that allo w you to scroll as you would with any wheel de vice on a mouse [...]

70 Getting Started Using external display de vices ❖ An external monitor or projector via the RGB (monitor ) Out port (Sample Illustration) Back of system Y ou cannot connect both the S-video Out port and the HDMI Ou t port to the same device at the same time. The system display default is set at the factory to S-video Out. Connecting an external[...]

71 Getting Started Using external display de vices Connecting to a TV using HDMI™-CEC (A vailable on certain models) HDMI™-CEC (Consumer Electronics Co ntrol) is a standard in the CE Industry which allows de vices to work together over an HDMI cable. T oshiba computers with HD MI-CEC include a T oshiba utility (may need to be installed) dedicat[...]

72 Getting Started Using an e xternal ke yboar d ❖ TV (or other external video de vice) only ❖ Built-in display and external monitor (extended desktop) ❖ Built-in display and TV (extended desktop) ❖ Swap-Switch primary display between int ernal display and external monitor when using extended desktop (Sample Image) Display options window Th[...]

73 Getting Started Using a mouse Using a mouse Y ou may want to use a mouse instead of the computer’ s built-in T o uchPad. Y ou can use a USB-compatible mouse. Connecting a printer Y our printer documentation may require you to install the printer software before physically connecting the printe r to your computer . If you do not install the sof[...]

74 Getting Started Connecting an option al e xternal diskette drive Setting up a printer Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure. If your printer does not support Plug and Play , follo w these steps to set it up for the first time. Y o[...]

75 Getting Started T urning off the computer T o connect an optional external USB disk ette driv e, connect the cable to one of the comput er’ s USB ports. (Sample Illustration) Connecting a n optional external USB diskette drive T urning off the computer Pressing the power button before shutting down the Windows ® operating system could cause y[...]

76 Getting Started T urning off the computer TECHNICAL NOTE: Before using the Shut Down option to turn off your computer , save your files and make sure all disk/dis c activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again. ❖ Use the Sleep command to save [...]

77 Getting Started T urning off the computer Sleep mode The Sleep command places the comput er into a power -saving mode. Sleep sa ves the current state of the computer to memory so that, when you restart the comp uter , you can continue working from where you left of f. After your computer sleeps for an extended period of time, the Windows ® oper[...]

78 Getting Started T urning off the computer Using the Shut Down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns off your computer . Use the following steps to turn of f your co[...]

79 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. (Sample Image) Advanced settings tab of P ower Options scr een 4 Click Power buttons and lid to display the actions that you can configure. 5 Select the options you want from the drop-down lists. Thes[...]

80 Getting Started T urning off the computer Once the computer is conf igured, you can turn it off b y either pressing the power b utton or closing the display panel, depending on the options set . Restarting your computer T o start the computer up again, press the po wer b utton unt il the on/off light glo ws white or green, depending on y our mod[...]

81 Getting Started T urning off the computer T o use any of these methods, you f irst need to enable them using the Power Options feature. 1 Click Start , Contro l Panel , System and Maintenance , and then Po wer Options . The Po wer Options window appears. 2 Click Change plan s ettings under the po wer plan to be customized. The Edit Plan Settin g[...]

82 Getting Started T urning off the computer ❖ Po wer button action Set this option to Hibernate if you want the computer to go into Hibernation mode wh en you press the power button. ❖ Start menu po wer button Set this option to Hibernate if you want the computer to go into Hibernation mode wh en you click the power button in the Start men u. [...]

83 Getting Started T urning off the computer 2 Click Sleep . The computer sa ves the status of all open programs and files to the memory , turns off the display , and enters into a low-po wer mode. The on/off light blinks amber indicating the computer is in Sleep mode. Configuring Sleep mode options Y ou can place the computer into Sleep mode by ei[...]

84 Getting Started T urning off the computer 4 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. (Sample Image) Advanced settings tab of P ower Options screen 5 Click Power buttons and lid to display the actions that you can configure. 6 Select Sleep for the options you want. These options can be[...]

85 Getting Started Customizing your computer’ s settings Once the computer is conf igured, you can place it into Sleep mode by either pressing the po wer button or closing the display panel, depending on the Sleep options set. Starting again from Sleep mode T o start up the computer from Sleep mode, press the power b utton until the on/off light [...]

86 Getting Started Caring for your computer Moving the computer Before moving your computer, e ven across the room, make sure all disk activity has ended (the driv e indicator light stops glowing) and all external peripheral cables are disconnected. Do not pick up the computer by its display panel or by the back. Doing so could damage the system. U[...]

87 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the disk. If the network you are using goes down and you must restart your compu ter to reconn[...]

88 Learning the Basics Computing tips ❖ Back up your files to disks (or other remov able media) on a regular basis. Label the backup co pies clearly and store them in a safe place. It is easy to put of f backing up because it takes time. Ho wev er , if your hard disk suddenly fails, you will lose all the data on it unless you have a separate back[...]

89 Learning the Basics Using the ke yboar d Using the keyboard Y our computer’ s ke yboard contai ns character keys, control ke ys, function ke ys, and special W indo ws ® ke ys, providing all the functionality of a full- size ke yboard. (Sample Illustration) Ke yboar d Character keys T y ping with the character keys is very mu ch li ke ty pi ng[...]

90 Learning the Basics Using the ke yboar d Ctrl, Fn, and Alt keys (Sample Illustration) Ctrl, Fn, and Alt keys The Ctrl , Fn , and Alt keys do different things depending on the program you are using. For more inform ation, see your prog ram documentation. Function keys The functio n keys (no t to be confused with the Fn key) are the 12 keys at the[...]

91 Learning the Basics Using the ke yboar d Overlay keys The ke ys with gray numbers and symbols on the front of them form the numeric and cursor ov erlay . This overlay lets you enter numeric data or control the cursor as you would using the 10-key ke ypad on a desktop comput er’ s k eyboard . (Sample Illustration) Numeric and cursor contr ol ov[...]

92 Learning the Basics Starting a pr ogram Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. T o f ind the file, use the Start menu or W indo ws ® Explorer . If you prefer to open the program f i rst, you hav e four options. Y ou can: ❖ Double-click th[...]

93 Learning the Basics Starting a pr og ram Starting a program from Windows ® Explorer If a program is not listed in th e All Programs menu, yo u can start it from W indows ® E xplorer . W indo ws ® Explorer gi ves you a view of your computer’ s contents as a hi erarchy or “tree. ” Y ou can easily see the contents of each driv e and folder[...]

94 Learning the Basics Saving your work Starting a program using the Start Search field This example uses the Start menu’ s Start Search f ield to start Wo r d P a d : 1 Click Start to display the Start menu. The Start Search f ield appears at the bottom of the Start menu. (Sample Image) Start Sear ch f ield in Start menu 2 Start typing the progr[...]

95 Learning the Basics Saving your work Saving files 1 In your Windo ws ® -based application, click File , and then Sav e . 2 Click Browse f olders . If you are working with a docum ent that already has a f ile name, this is all you need to do. If y ou created a new document, your program displays a Sav e As dialog box. Use this dialog box to spec[...]

96 Learning the Basics Printing your work Using a file extension Most programs assign an extension to the f ile name that identifies the file as being created in the pr ogram with a particular format. F or example, Microsoft ® W ord saves f iles with a .doc extension. Any file name with an extension of “.doc” is assumed to be a Microsoft ® W [...]

97 Learning the Basics Backing up your work 3 Specify the print parameters. For e xample, the range of pages and number of copies to print. 4 Click Print . Backing up your work Back up all the files you create in case something happens to your computer . Y ou can back up your files to dif ferent types of media such as CDs, D VDs, diskettes, or to a[...]

98 Learning the Basics Using the optical drive For these reasons, your computer may come with an optical dri v e. TECHNICAL NOTE: Y our optical drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region. The drive will allow you to[...]

99 Learning the Basics Using the optical drive Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Media control buttons (A vailable on certain models) The media control buttons located on the system control panel above the keyboard let you mute the sound and play audio CDs or D VD movie[...]

100 Learning the Basics Using the optical drive 4 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty , clean it as described in “Caring for optical discs” on page 103 . 6 Place the disc carefully in th e disc tray , label sid[...]

101 Learning the Basics Using the optical drive If you insert the disc incorrectly , it may jam the drive. If this happens, contact T oshiba support for assistance. 9 Push the disc tray in by pressing gently on the center of the tray until it clicks into place. Y ou are ready to use the disc. Playing an audio CD Insert an audio CD and close the dis[...]

102 Learning the Basics Using the optical drive For more information regarding supported optical media formats please refer to your computer’ s detailed specif ications at pcsupport.toshiba.com . Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your T [...]

103 Learning the Basics T oshiba’ s online r esour ces Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. 2 Pull the tray out until it is fully open , remove the disc, and place it in its protecti ve co ver . 3 Gently press the tray in to close it. Caring for optical discs ❖ Store y[...]

104 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your com puter while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process. It has a number of other features that enhanc e its energy ef ficiency .[...]

105 Mobile Computing Running the computer on battery power Running the computer on battery power The computer contains a remov abl e Lithium-Ion (Li-Ion) battery that provides po wer when you are aw ay from an A C outlet. Y ou can recharg e it many ti mes. Battery Notice Battery life may vary considerably from specif ications depending on product m[...]

106 Mobile Computing Running the computer on battery power The computer also has an internal real-tim e-clock (R TC) battery . The R TC battery po wers the R TC me mory that stores your system configuration settings and the curren t time and date informatio n. It maintains this information fo r up to a month while the computer is turned off. TECHNI[...]

107 Mobile Computing Char ging ba tteries Charging batteries The battery needs to be charged be fore you can use it to power the computer . Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery . Always use the battery charger specified by T oshiba. Y ou can order a T os[...]

108 Mobile Computing Char gi ng batteries Leav e the po wer connected and the battery should begin charging after a fe w minutes. HINT : Once the battery is fully charged, we recom mend that you operate your computer on battery power until the batter y discharges completely . Doing this extends battery life and helps ensure accurate monitoring of b[...]

109 Mobile Computing Monitoring main battery power Monitoring main battery power The computer’ s main battery light gives you an indication of the main battery’ s current charge. Th e follo wing also applies to the secondary battery (av ailable on certain models) if installed. ❖ Glows amber while the main battery is bei ng charged (A C adapto[...]

110 Mobile Computing Monitoring main battery power (Sample Illustration) P ower and batt ery light locations Determining remaining battery power Wait at least 16 se conds after turning on the computer before trying to monitor the remaining battery power . The computer needs this time to check the battery’ s remaining capacity and perform its calc[...]

111 Mobile Computing Monitoring main battery power TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaini ng charge frequently if you are working in temperatures below 50 degrees Fahrenheit. The computer calculates the remaining battery charge based on your current rate of power use and other factors such as [...]

112 Mobile Computing Monitoring main battery power 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. (Sample Image) Advanced settings tab of P ower Options screen 4 Click Battery to display the battery options. 5 Configure the alarm settings to suit your needs. Conserving batter y power How lon[...]

113 Mobile Computing Monitoring main battery power Microsoft ® has combined these options into preset Po wer Plans . Using one of these power plans lets you choose betw een maximum power sa vings and peak system performance. Y ou may also set individual po wer-sa ving options to suit your own needs. The follo wing sections describe how to choose a[...]

114 Mobile Computing Monitoring main battery power 5 Click Change Adv anced Sett ings to access settings for battery notification lev els, hard drive po wer sav e time, etc. Y ou can click on the plus signs to expa nd each item and to see what settings are a vailable for each item. 6 Click Sa ve Change s to sav e the plan changes you ha ve performe[...]

115 Mobile Computing Changing the main battery Changing the main batter y When your main battery has ru n out of power , you have two options: plug in the A C adaptor or install a char ged main battery . Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive obj[...]

116 Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlo cked position. (Sample Illustration) Unlocking the battery r elease lock 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer . (Sample Illustration) Removing the battery If the battery is leaking or it[...]

117 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks. The battery pack has been designe d so that you cannot install i t with rev erse polarity . [...]

118 Mobile Computing T aking car e of your battery 4 T urn the computer right side up. 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 115 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life. S[...]

119 Mobile Computing T aking car e of your battery Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doi[...]

120 Mobile Computing Disposing of used b atteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you hav e fully recharged the battery . Y ou must discard a batter y if it becomes damaged. Never attempt to dispose of a battery pack by[...]

121 Mobile Computing T raveling tips T o shiba is dedicated to preservi ng the en vironment by sponsoring Call2Recycle™ , a program of the Rechar geable Battery Recycling Cor por ati on. For more information and for drop-of f locations, visit www .rbrc.org or call 1-800-822- 8837. Notice regarding CR coin cell batteries, applicable to California,[...]

122 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system. Y ou use its features to start programs, find documents, set up system components, and perform[...]

123 Exploring Y our Computer’ s Features Exploring the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, T askb ar , Notification Area, and background pattern. (Sample Image) W indows ® oper ating system deskt op Icons An icon represents a folder , file, or program t[...]

124 Exploring Y our Computer’ s Features Explorin g the desktop Y our desktop may contain othe r icons depending on your configuration. See W indo ws ® online Help for more specific information on each icon and ho w to use it. Start button Y ou use the Start button to: ❖ Start programs ❖ Open documents ❖ Adjust system settings ❖ Find fil[...]

125 Exploring Y our Computer’ s Features Setting up for communications Setting up for communications T o connect to the Internet, use an online service, or communicate across the telephone lines with another computer , you need: ❖ A browser or communications program ❖ An Internet Service Pro vider (ISP ) or online service if you plan to use t[...]

126 Exploring Y our Computer’ s Features Setting up for communications Accessing a network T o access a network: ❖ At the of fice, c onnect an Ethern et cable to the RJ45 jack on your computer . For specific info rmation about connecting to the network, consult your network administrator . Many hotels, airports, and of fices of fer W i-Fi ® ac[...]

127 Exploring Y our Computer’ s Features Setting up for communications For more detailed i nformation regarding y our computer’ s modem, visit T oshiba’ s W eb site at accessories.toshiba.com . Before you can communicate using th e modem, you need to connect it to a telephone line. Y ou r computer’ s b uilt-in modem port provides an RJ-11 j[...]

128 Exploring Y our Computer’ s Features An overview of using the Internet An overview of using the Internet The following sections giv e a quick introduction to the Internet an d some of its exciting featur es, under these headings: ❖ The Internet ❖ The W orld Wi de W eb ❖ Internet Service Providers ❖ Connecting to the Internet ❖ Surfi[...]

129 Exploring Y our Computer’ s Features An overview of using the Internet Connecting to the Internet T o connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A W eb browser ❖ An Internet Service Provider (ISP) account Once you hav e established an ISP account, you can connect to the Internet. 1 Connect you[...]

130 Exploring Y our Computer’ s Features Explor ing audio feat ur es ❖ Internet chat roo ms A chat room is a W eb site that offers a place whe re people with similar interests and ideas comm unicate in real-time, one-on- one or in groups, by typing messages which are instantly viewed by others on their computer screens. ❖ Internet news groups[...]

131 Exploring Y our Computer’ s Features Explorin g audio featur es 2 Click Start , All Programs , Acces sories , and then Soun d Recorder . (Sample Image) Soun d Recor der scr een 3 Click the Start Recording button. 4 Speak normally into the microphon e. 5 When you hav e f inished recording, click the Stop Recording button. The Sa ve As dialog b[...]

132 Exploring Y our Computer’ s Features FM tuner FM tuner (A vailable on certain models) Y our computer may come equipped with a built-in FM tuner and a separate FM antenna. With this FM tuner feature you can listen to li ve local FM radio stations. T o use th is feature: 1 T urn your computer on. 2 Plug in the FM antenna into the FM tuner port [...]

133 Exploring Y our Computer’ s Features Using an ExpressCar d ® Dependin g on your computer mode l, the process of sendi ng E-mail, taking pictures or recording video messages m ay vary . The W eb Camera soft ware, by default, should already be running in the Notification Area. Using an ExpressCard ® The ExpressCard ® slot supports the use of[...]

134 Exploring Y our Computer’ s Features Using the Bridge Media Adapter Slot 2 Gently press the ExpressCard inward to release it. The ExpressCard pops out slightly . 3 Grasp the ExpressCard an d pull it straig ht out. (Sample Illustration) Removing an Expr essCar d Using the Bridge Media Adapter Slot (A vailable on certain models) The Bridge Medi[...]

135 Exploring Y our Computer’ s Features Using the Bridge Media Adapter Slot 2 Push the media into the ad apter until it locks in place. (Sample Illustration) Inserting memory med ia When inserting memory media, do not touch the metal contacts. Y ou could expose the storage area to static electric ity , which can destroy data. Removing memor y me[...]

136 Exploring Y our Computer’ s Features Using the i.LINK ® port Using the i.LINK ® port The i.LINK ® port on the side of the computer pro vides an extremely fast data transfer rate. In addition to high speed, the i.LINK ® port also supports isochronous data transfer (the delive ry of data at a guaranteed rate). This makes it ideal for de vic[...]

137 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help yo u to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change default optio ns. These utilities are described in this chapter . The utilities described in thi[...]

138 Utilities TOSHIB A Assist ❖ TOSHIB A Accessibility ❖ Fingerprint Authentication Utilit y ❖ ConfigFree® TOSHIBA Assist The TOSHIB A Assist pro vides qui ck access to computer functions and allows you to customize a range of com puter settings. T o access TOSHIB A Assist, do one of the following: ❖ Double-click the TOSHIB A Assist shortc[...]

139 Utilities TOSHIB A Assist Connect The features av ailable in this category are: ❖ ConfigFree ® Connectivity Doctor ❖ Bluetooth ® Settings ❖ Bluetooth ® Local COM Setting s (Sample Image) T OSHIBA Assist window – Connect tab[...]

140 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secur e tab[...]

141 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility (Sample Image) T OSHIBA Assist window – Pr otect & Fi x tab[...]

142 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ TOSHIB A SD™ Memor y Card Format Util ity ❖ Mouse Utility ❖ TOSHIB A Hardware Se tup ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ CD/D VD Dri ve Acoustic Silencer ❖ TOSHIB A Accessibility (Sample Image) T OSHIBA Assist window – Optim[...]

143 Utilities TOSHIB A Applicati on Installer TOSHIBA Application Installer (A vailable on certain models) The TOSHIB A Application Installer allows you to reinstall the dri vers and applications that were originally bundled with your computer . T o reinstall driv ers and applications: 1 Double-click the TOSHIBA A pplication Installer icon on the W[...]

144 Utilities Setting passwor ds Setting passwords Setting a password lets you walk away from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can w ork on your computer again. T oshiba supports se ve ral types of passwords on you r computer: ❖ An instant password?[...]

145 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, T oshiba strongly recommends that you save your password in a location where you can later access it should you not r[...]

146 Utilities Setting passwor ds 6 Click OK . A pop-up screen ap pears asking for the User Password Mode. 7 Select whether the user password allo ws the user to change the hardware configuration: ❖ Able to run HwSetup —User can change the hardware configuration ❖ Unable to run HwSetup — User cannot change the hardware conf iguration (superv[...]

147 Utilities Setting passwor ds T o register a password for the po wer -on password functions: 1 Click Start , All Programs , To s h i b a , Utilities , and then TOSHIB A Assist . The TOSHIB A Assist windo w appears. 2 On the left side, click the Secure tab . 3 Click the User Password icon. The Password tab of the TOSHIB A Hardware Setup windo w a[...]

148 Utilities TOSHIB A PC Dia gnostic T ool Utility 4 Click Not Registered. A pop-up screen ap pears asking for a password. 5 Enter the user password, then click OK . TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose problem s with devices in your computer . Refer to the online Help documentatio n within the application for additi[...]

149 Utilities TOSHIB A SD™ Memory Car d F ormat Utility TOSHIBA SD ™ Memor y Card Format Utility This utility is used to for mat SD ™ cards used with the Bridge Media Adapter slot. T o format an SD memory car d using this util ity: 1 Click Start , All Programs , To s h i b a , Utilities , and then SD Memory Card F ormat . The TOSHIB A SD Memo[...]

150 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contr ol Panel , and then Mouse under Hardwa re and Sound , or click the Mouse icon in the Optimize tab of TOS HI BA A ss is t . The Mouse Properties screen appears. (Sample Image) Mo[...]

151 Utilities TO S H I B A H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the T oshiba configuration management tool av ailable through th e W indows ® operating system. T o access it: ❖ Click Start , All Programs , To s h i b a , Utilities , and then HWSetup , or clic k the TOS HI BA H ar dw are S et u p i con in the [...]

152 Utilities TO S H I B A H a rd w a re S e t u p ❖ CPU —Allows you to enable or disable CPU frequency switching modes Dynamically Swit chable —This mode is th e default setting for your computer , and automatica lly changes the processing frequency and decreases v oltage depending on the power source: ❖ AC P o w e r —If your computer is[...]

153 Utilities TO S H I B A H a rd w a re S e t u p This function can only be used for po rts that support the USB Sleep and Charge function (her einafter calle d “compatible ports”). Compatible ports are USB port s that hav e the ( ) symbol icon. Y ou can use the “USB Sleep and Charge function” to charge certain USB-comp atible ex tern al d[...]

154 Utilities TO S H I B A H a rd w a re S e t u p Metal paper clips or hair pins/clips will generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag. USB Sleep and Char ge function Settings —The default setting is Disabled. Changing[...]

155 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 211 ). Y ou may select all applications or any subset of the following: ❖ Microsoft ® Internet Explorer ® ❖ Microsoft ® Of f ice ❖ W indo [...]

156 Utilities TOSHIB A Button Support For more information about how to use the T OSHIBA Zooming Utility , right-click the icon in the Notification Area and then click Help . TOSHIBA Button Support TOSHIB A Button Support allows you to customize the Mute and Media buttons . These buttons ar e located on the system control panel directly above the k[...]

157 Utilities CD/D VD Drive Acousti c Silencer CD/DVD Drive Acoustic Silencer This utility can slow the speed of your optical driv e to make it run more quietly . Y ou can use this utility to m ake listening to music CDs more enjoyable. When you change the optical drive to “Silence” mode, the setting is only valid for the current Windows ® ses[...]

158 Utilities TOSHIB A Accessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot key combination wit h one of the function ke ys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a sti cky key , meaning you can press it once, r[...]

159 Utilities F ing erprint Authent ication Utility Fingerprint Authentication Utility (A vailable on certain models) The fingerprint authentication utility (av ailable on certain models) can be used to replace the ke yboard-based user password authentication syst em when booti ng up. The fingerprint authentication uti lity can also be us ed for us[...]

160 Utilities F ing erprint Authenticati on Utility Fingerprint Logon The fingerprint utility enables logon to your comp uter using fi ngerprints. During us er enrollment, f ingerpr int samples are sav ed and associated with the user’ s W indows ® user account. When the user attempts to log on again, th e user’ s fi ngerprint is read and compa[...]

161 Utilities F ing erprint Authent ication Utility ❖ A void the follo wing finger conditions for enrollment or recognition as they may result in fingerprint enrollment erro rs or a drop in the f ingerprint recognitio n success rate. ❖ Soaked or swollen fi nger (e.g., after taking bath) ❖ Injured finger ❖ We t f i n g e r ❖ Soiled or oily[...]

162 Utilities ConfigF r ee® ❖ The recognition success rate may dif fer from user to user . ❖ T o shiba does not guarantee that this fingerprint recognition technology will be error -free. T o shiba does not guarantee that the f ingerprint reader will recognize the enrolled user or accu rately screen out unauthorized users at all times. T oshib[...]

163 Utilities ConfigF r ee® Starting ConfigFree ® T o start ConfigFree ® , be sure the computer has a wired or wireless connection. Then perform any of the follo wing steps: ❖ Click Start , All Programs , To s h i b a , Networking , and then Conf igFree . ❖ Double-click the Config Free ico n in the Notification Area. ❖ Press the TOSHIB A A[...]

164 Utilities ConfigF r ee® ❖ Status of W ireless Connection switch (Sample Image) Connect ivity Doctor scr een Profile Settings The Prof ile Settings utility lets you save network settings in “profiles . ” ConfigFree ® prof iles are useful for easily switching network settings an d devices. Y ou can switch network settings simply by select[...]

165 Utilities ConfigF r ee® T o create a profile: 1 Click the icon in the Notif ication Area. 2 Mov e the pointer to Prof ile . 3 Click Open Settings . The ConfigFree Prof ile Settings windo w appears. (Sample Image) ConfigF ree Pr ofile Settings windo w 4 Click Add to start the Create Prof ile W izard.[...]

166 Chapter 6 If Somet hing G oes W r ong Some problems you may encounter wh en using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself. It cov ers the problems you are most lik[...]

167 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask . Closing the failed prog ram should allow you to continue working. If it does not, c[...]

168 If Something Goes Wrong Pr oblems when you turn on the computer If you are using an A C adaptor , v eri fy that the computer is recei ving power from the external po wer source by looking at the A C power light. If the indicator is glo wing, th e computer is conn ected to a liv e external po wer source. The computer starts but when y ou pr ess [...]

169 If Something Goes Wrong Pr oblems when you turn on the computer If you are running on battery power , it is recommended that you do not lea ve the computer in Sleep mode for lo ng periods of time. T o charge the battery , leave the computer plugged into a liv e wall outlet for sev eral hours. For more information see “Charging batteries” on[...]

170 If Something Goes Wrong The W indo ws ® operating system is not working 5 V erify that the A C adaptor is th e correct unit for your computer model. The computer may not be abl e to start from an A C adaptor that is rated for less current (amperage) than the computer requires, e ven if the rated v oltage is correct, and the plug fits correctly[...]

171 If Something Goes Wrong The W indo ws ® operating system is not working ❖ Safe Mode with Command Pr ompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Kno wn Good Conf iguration (adv anced) ❖ Directory Services Restore Mode ❖ Deb uggin g Mode ❖ Disable automatic restar t on system failure ❖ Disable Driv e[...]

172 If Something Goes Wrong Resolving a hardwar e conflict The Windows ® operating system can help you If the operating system has started properly but you still ha ve a problem using your co mputer , the online Help can assist you in troubleshooting the pro blem. T o access the W indo ws ® operating syst em Help and Support: 1 Click Start , then[...]

173 If Something Goes Wrong Resolving a har dwar e conflict The device most recently connected to the system is th e one most likely to be causing a conflict. Resolving conflicts There are sev eral things you can do to resolve hardw are conflicts: ❖ Get the most recent dri vers from the manuf acturer . ❖ Disable the device. For an ol der de vic[...]

174 If Something Goes Wrong Resolving a hardwar e conflict ❖ The Resources tab, which lists resources assigned to the monitor , optional external opti cal driv e, optional external diskette dri ve, and other power -using functions. Thi s tab does not appear if the device is not using resources. ❖ The Driver tab, which displays th e dri vers bei[...]

175 If Something Goes Wrong Resolving a har dwar e conflict For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in slot A. Power and the batteries Y our computer receive s its po wer through the AC ada ptor and power cord/cable or from the system batteries (battery , o[...]

176 If Something Goes Wrong Resolving a hardwar e conflict The battery appears not to power the computer f or as long as it usually does. If you frequently repeat shallow char ge and disch a rge, the battery meter may become in accurate. Let the battery discharge completely , then try charging it ag ain. Check the po wer options vi a your Po wer Pl[...]

177 If Something Goes Wrong Resolving a har dwar e conflict Nothing happens when you pr ess the keys on the exter nal keyboard. Y ou may hav e plugged the external keyboard in while the computer was turned on. Using the computer’ s T ouchPad: 1 Click Start , and then click the arro w ne xt to the Lock button in the lower -right part of the Start [...]

178 If Something Goes Wrong Resolving a hardwar e conflict ❖ T ry adjusting the contrast and brightness controls on the external monitor . ❖ Press Fn and F5 simultaneously to make sure the display priority is no t set for the built-in screen . The screen does not look right. Y ou can change the display settings by clicking a blank area of the d[...]

179 If Something Goes Wrong Resolving a har dwar e conflict Small bright dots appear on yo ur TFT display when y ou turn on y our compu ter . Small bright dots ma y appear on your screen display wh en you turn on your computer . Y our disp lay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precisio[...]

180 If Something Goes Wrong Resolving a hardwar e conflict 6 Y ou can choose one or both options: ❖ Automatically f ix f ile system erro rs ❖ Scan for and attempt reco very of bad sectors 7 Click Start . Error-checking tests and repairs the disk. Y our hard disk seems very slo w . If you hav e been using your comput er for a long time, your fil[...]

181 If Something Goes Wrong Resolving a har dwar e conflict Optical drive problems Y ou cannot access a disc in the dri ve. If the optical dri ve is an e xternal driv e, make sure that the driv e’ s cable is properly connected to the computer . Make sure the tray that holds the optical disc is closed properl y . Press gently until it clicks into [...]

182 If Something Goes Wrong Resolving a hardwar e conflict The disc will not come out of the driv e when y ou click the eject button on the scr een. Press the b utton on the optical dri ve itself. For additional information see “Y ou press the disc eject button, b ut the dri ve tray does not slide out. ” on page 181 . Sound system problems No s[...]

183 If Something Goes Wrong Resolving a har dwar e conflict ExpressCard ® checklist ❖ Make sure the card is insert ed properly into the slot. ❖ Make sure all cables are securely connected. ❖ Occasionally a defecti ve ExpressCard ® slips through quality control. If another computer wit h a ExpressCard slot is av ailable, try the card in that[...]

184 If Something Goes Wrong Resolving a hardwar e conflict 3 Select the item you wish to remove and click OK . 4 Remov e the device when told it is safe to do so. Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported. For more information on Hibernation and Sleep modes see ?[...]

185 If Something Goes Wrong Resolving a har dwar e conflict Y ou may have connected the printer while the computer is on. Disable Sleep mode, turn off the computer, and turn of f the printer . T urn the printer back on, make sure it is online, and then turn the computer back on. T ry printing another file. For exam ple, you could create and attempt[...]

186 If Something Goes Wrong Resolving a hardwar e conflict Wireless networking problems This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi ® ) networking. The terms and concepts used assume a bas ic understanding of networks, and may be for more advanced users. If you need assistance or if you [...]

187 If Something Goes Wrong Resolving a har dwar e conflict ❖ V erify that the network connection is configured to obtain its Internet Protoco l (IP) address dynamically: 1 Click Start , and then Network . 2 Click V iew Status . 3 Click Details . 4 V e rify that the DHCP E nabled setting is set to Ye s . 5 Click Close . ❖ Use IPCONFIG to verify[...]

188 If Something Goes Wrong D VD operating pr ob lems The Windows ® operating system wireless management facility does not work. If you are using an external W i-Fi ® adapter (an ExpressCard ® , USB adapter , or other variety), check if the adapter comes with its o wn management utility . If it does, the utility may be disabling the W indows ® [...]

189 If Something Goes Wrong Develop good computing habits 3 Select Never on When to turn of f the display . 4 Click Sav e changes . The screen sa ver runs while y ou ar e watching a movie or title. If the screen sav er is enabled, it runs on top of any movie or title you are watching. T o disable the screen sa ver: 1 Right-click on the desktop and [...]

190 If Something Goes Wrong Develop good computing habits Read the user’ s guides. It is very dif ficult to provide a f ail-safe set of steps you can follow ev ery time you experience a problem with the computer . Y our ability to solve problems will improve as you learn about ho w the computer and its software work together . Get familiar with a[...]

191 If Something Goes Wrong Develop good computing habits 4 In the input field, enter a name that is descripti ve enough to be easily understood in the future, such as “Before inst alling Brand X Accounting app. ” Then click Create . 5 The W indo ws ® operating system creates the Restore Point, automatically stamps it with the current date and[...]

192 If Something Goes Wrong Develop good computing habits Backing up your data or your entire computer with the Windows ® operating system The most v aluable component of y our computer system is the data you create and store on its hard dr ive. Since problems with either hardware or software can mak e the data inaccessible or even destroy it, the[...]

193 If Something Goes Wrong Develop good computing habits General tips for installing hardware and software Here are a fe w tips to help ensure safe and easy installation of ne w hardware (printers, pointing devices, e xternal hard drives, D VD writers, scanners, etc.) and software (applications like Microsoft ® Of fice and Adobe ® Photoshop ® ,[...]

194 If Something Goes Wrong Develop good computing habits 5 Use the new hardw are or software for a while, noting any new problems. Mak e sure that your critical applications (e- mail, business applications, etc.) are w orking correctly , and verify that important de vices are still functioning. 6 For each additional hardware or software item, repe[...]

195 If Something Goes Wrong If you need further assistance If you need further assistance If you have follo wed the recomm endations in this chapter and are still having problems, you may n eed additional technical assistance. This section contains the step s to take to ask for help. Before you contact T oshiba Since some problems m ay be related t[...]

196 If Something Goes Wrong Other T oshiba Internet W eb sites T oshiba voice contact Before calling T o shiba, make sure you have: ❖ Y our computer’ s serial number ❖ The computer and any optional devices related to the problem ❖ Backup copies of your Wi ndows ® operating system and all other preloaded software on your choice of media ❖[...]

197 If Something Goes Wrong T oshiba’ s worldwide of fices For more information on additio nal T osh iba worldwide locations, please visit: www .toshiba. co.jp/i ndex. htm . France T o shiba Systèmes (France) S.A. 7, Rue Ampère; B. P . 131 92800 Puteaux Cédex France Germany T oshiba Europe GmbH Leibnizstraße 2 D-93055 Regensbu rg Germany Ital[...]

198 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards provi de a quick way to modify selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot Ke y Cards and Application Cards. Hot Key Cards The Hot Ke y Cards are used to set or modify the following system functions: ❖ Mu[...]

199 Hot Keys /TOSHIBA Ca rds Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off. Hot keys have a legend on the key indicating the option o[...]

200 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 138 . PC Diagnostic T ool utility For more information, refer to “TOSHIB A PC[...]

201 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Using the Application Cards T o launch an application using the Application Card s: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen. (Sample Image) TOSHIB A Car d display 2 Click the “stack ed” card on the far right of the display . The Appli[...]

202 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 3 The Card Case displays tw o rows of Cards. Cards that appear solid (not tr ansparent) in the bottom ro w are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards. 4 T o enable a card, drag it from the top row to the [...]

203 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer . or Fn + This TOSHIB A Card or hot ke y blanks the display . Selecting th[...]

204 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window . Selecting this Card or pressing the hot[...]

205 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep m ode” on page 82 . Selecting this Card or pressing the hot ke y displays the following options: (Sample Imag[...]

206 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 80 . Selecting thi[...]

207 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the power - o n d i sp l a y o p t io n s (only the f irst option is av ailable when you do not have an external monitor attached) (the last option is available only if you are in Extend ed Display Mode[...]

208 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-i[...]

209 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the Wi-Fi ® module. ❖ Bluetooth ® enabled—Enables just t[...]

210 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T o uchPad. For more information on using the T ou chPad, see “Disabling or enabling the T ouchPad™” on page 69 . Selecting this Card or pressing the hot key displays the follo[...]

211 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution. Selecting this Card or pressing the hot ke y displays the following options: (Sample Image) Scr een r esolution options Cycle through the screen resolu tions, then select the[...]

212 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot k ey turns the curs or control overlay on and off. Fn + This hot k ey turns the numeric overlay on and of f. Fn + This hot k ey turns the scroll lock feature on and off. Fn + This hot key tu rns the TO SHIB A Zo o mi ng Utility to zoom-out. [...]

213 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our computer features a uni versal po wer supply you can use worldwide. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world. USA and Canada UL ap prove d CS A a pp roved United Kingdom BS ap pr oved Australia AS ap pr [...]

214 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide. AC alternating current BIOS basic input/output system bps bits per second CD compact disc CD-R OM compact disc read-only memory CD-R W compact disc re write memory CMOS co[...]

Glossary 215 DOS disk operating system DPI dots per inch DSTN dual supertwist nem atic DV D digital versatile (or video) disc DV D - R O M digital versatile (or video) disc read-only memory ECP enhanced capabilities po rt EPR OM erasable programmable read-only memory FAT f ile allocation table FCC Federal Communicat ions Commission GB gigabyte HDD [...]

216 Glossary SDRAM synchronous dynamic random access memory SRAM static random access memory SVGA super video graphics adapter TFT thin film transistor USB univ ersal serial b us URL uniform resource lo cator WA N wide area netw ork www W orld Wide W eb Te r m s The following terms may appear in this user’ s guide. A active-matrix display — A l[...]

Glossary 217 baud rate — The speed at which a comm unication de vice, such as a printer or mo dem, transmits in formation. Baud rate is the numb er of signal changes per second (not necessarily the same as bits per second). See also bits per second . BIOS (basic input/ output syst em) — Basic instructions, stored in read- only memory (R OM), co[...]

218 Glossary central processing unit (CPU) — The chip that functions as the “brain” of the computer . It takes informa tion from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character — Any letter , number , or symbol you can use on the compu[...]

Glossary 219 D default — The setting selected by a program when the user does not specify an alternati ve setting. device — A component attached to the computer . Devices may be external (outside the computer’ s case) or internal (inside the computer’ s case). Printers, disk dr iv es, and modems are examples of devices. device dri ver — A[...]

220 Glossary double-click — T o press and release the pointing device’ s primary button rapidly twice without moving the pointing device. In the W indows ® operating system, this refers to the pointing device’ s left button, unless otherwise stated. double-density d iskette — A 3.5-inch diskette that can hold up to 720 KB of information (h[...]

Glossary 221 F fil e — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also docum ent. f ile allocation table (F A T) — The section of a disk that keeps track of the location of files stored on the disk. fil e n a m e — A set of characters that u[...]

222 Glossary Hibernation — A feature of many T oshiba computers that sav es to the hard disk the current state of your work, in cluding all open files and programs, when you turn the computer off. When you turn on the computer again, your w o rk is returned to the same state it was when the computer was turned of f. See also Sleep, Suspend. high-[...]

Glossary 223 liquid crystal disp lay (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it. A filter o ver the electrodes permits only non-polarized l[...]

224 Glossary N network — A collection of computers a nd associated de vices that are connected by communications facilities. A network allows you to share data and peripheral de vices, su ch as printers, with other users and to exchange electronic mail. non-interlaced — A method of refreshing a computer scr een, in which each pixel of e very li[...]

Glossary 225 Plug and Play — Generally , refers to the com puter’ s ability to automatically configure itsel f to work with peripheral devices. When capitalized, refers to a sta ndard that, when followed by a device manufacturer , allo ws a computer to conf igure itself automatically to work with the device. pointing de vice — Any de vice, su[...]

226 Glossary RJ11 — A modular connector used o n most U.S. telephone systems and direct-connect modems. The RJ11 co nnector is a 6-wire connector . R OM (read-only memory) — Non-v olatile memory that can be read but not written to. Non-volatile here means that information in ROM remains whether or not the computer is recei ving power . This typ[...]

Glossary 227 U universal serial bus (USB) — USB is a serial b us that supports a data transfer rate of up to 4 80 Mbps (480 million bi ts per second). USB can connect up to 127 peripheral de vices through a single all- purpose USB port. USB allows hot swapping of peripherals. See also bus, hot swapping, serial. upload — T o send a file to anoth[...]

228 Index A A C adaptor 47 AC p o w e r connecting adaptor 48 accessories memory 52 adding memory 52 Alt keys 90 Application Cards 200 audio fil e s 130 audio features 130 B backing up files 88 battery changing 115 charge indicator light 49 , 109 charge not lasting 176 charging 47 , 49 conserving po wer 112 disposal 120 lo w charge 111 monitoring p[...]

229 Index cleaning 85 moving 86 non-system disk or disk error message 169 not accessing disk driv es 168 running on battery power 105 setting up 44 , 54 warning resume failure messag e 168 computer lock 86 computing tips 87 ConfigFree® 162 connecting 71 connecting to a power source 47 connection set up 126 control buttons 69 Ctrl keys 90 D desktop[...]

230 Index F F A T (File Allocation T able) 179 file e xtensions 96 file, backing up 88 fil e s backing up 97 printing 96 restoring 97 saving 94 fi ngerprint authentication 159 fingerprint Authentication Utility using 159 Fn keys 90 function keys 90 H hardware conflicts 172 resolving 173 headphones using 131 Help and Support W indo ws® operating sy[...]

231 Index L lock computer , using 86 M main battery removing 115 memory adding 52 problem solving 174 remo ving memory module slot cov er 55 memory module inserting 56 installation 53 removing 59 memory module slot 55 microphone 130 modem connecting to telephone line 126 problem solving 185 monitor 69 connecting 70 not working 177 mouse installing [...]

232 Index printer connecting 73 problem solving 184 , 18 5 printing a file 96 problem solving AC p o w e r 175 accessing disk dri ves 168 battery charge does not last 176 battery not charging 175 cannot insert diskette in drive 180 cannot read a diskette 180 changing display properties 178 checking device properties 173 computer hangs when ExpressC[...]

233 Index set up communications 125 setting up adding memory 52 computer 44 , 54 work en vironment 41 setting up a connection 126 Sleep mode 77 hot key 205 starting again from 85 sound problem solving 182 sounds recording 130 speakers using external 131 start button 124 Start Search field 94 starting a program 92 Start Search field 94 W indo ws® E[...]