Toshiba qosmio f10 manuel d'utilisation

1 Toshiba Personal Computer QOSMIO F10 Maintenance Manual TOSHIBA CORPORATION File Number 960 - 498[...]

ii QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Copyright © 2004 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in an y form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba QOSMIO F 10 Mainte[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer QOSMIO F 10. NOTE: Each model of QOSMIO F 10 has a different con figuration. For each model’s configuration, refer to the parts list dedicated to it. The procedures described in t[...]

iv QOSMIO F 10 Maintenance Manual (960 - 49 8 ) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the QOSMIO F 10 system unit and each F RU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operation[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) v C onventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition . For example: Read Only Memory (ROM) Keys K[...]

vi QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table of Contents Chapter 1 Hardware Overview 1.1 Features ...................................................................................................................... 1 - 1 1.2 System Block Diagram .............................................................................................[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) vii Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3 - 1 3.2 Executing the Diagnostic Test ................................................................................... 3 - 4 3.3 Setting of [...]

viii QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Chapter 4 Replacement Procedures 4.1 O verview .................................................................................................................... 4 - 1 4.2 Battery pack/PC card/Bridge Media .......................................................................... 4 - 8 4.3 HDD ...[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) ix Appendices Appendix A Handling the LCD Module ......................................................................... A - 1 Appendix B Board Layout .............................................................................................. B - 1 Appendix C Pin Assignment .........................[...]

x QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

Chapter 1 Hardware Overview[...]

1 Hardware Overview 1 - ii QOSMIO F10 Maintenance Manual (960 - 49 8 ) 1 Hardware Overview[...]

1 Hardware Overview QOSMIO F10 Maintenance Manual (960 - 49 8 ) 1 - iii Chapter 1 Contents 1.1 Features ...................................................................................................................... 1 - 1 1.2 System Block Diagram .............................................................................................. 1[...]

1 Hardware Overview 1 - iv QOSMIO F10 Maintenance Manual (960 - 49 8 ) Figures Figure 1 - 1 Front of the computer and the system units configuration ............................ 1 - 4 Figure 1 - 2 System bloc k diagram .................................................................................... 1 - 5 Figure 1 - 3 2.5 - inch HDD ............[...]

1 Hardware Overview 1.1 Features QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 1 1 Features 1.1 Features The QOSMIO F10 series are high performance all - in - one PCs running a Pentium - M processor. The features are listed below. ? Microprocessor Microprocessor that is used depends on the model. Mobile Intel ® Pentium ® - M Pentium - M 1.50GH[...]

1.1 Features 1 Hardware Overview 1 - 2 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) ? Display LCD Built - in 15.4 - inch, XGA (1,280 x 800 dots), 262,144 colors, amorphous silicon TFT color display. Clear Super View LCD. CRT Supported via a RGB connector. TV - out S - VIDEO/Composite out port is supported. (Supporting NTSC, PAL and SECAM) D - VIDEO[...]

1 Hardware Overview 1.1 Features QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 3 ? Battery The R TC battery is mounted inside the computer. The main battery is a detachable lithium ion battery (4,400mAh:Li - Ion, 6 - cell). ? USB ( Universal Serial Bus ) Four USB ports are provided. The ports comply with the USB2.0 standard, which enables data t[...]

1.1 Features 1 Hardware Overview 1 - 4 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Figure 1 - 1 shows the front of the computer and the system units configuration. Figure 1 - 1 Front of the computer and the system units configuration[...]

1 Hardware Overview 1.2 System Block Diagram QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 5 1.2 System Block Diagram Figure 1 - 2 shows the system block diagram. Figure 1 - 2 System b lock d iagram[...]

1.2 System Block Diagram 1 Hardware Overview 1 - 6 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) The PC contains the following components . ? CPU Mobile Intel ® Pentium ® - M Pentium - M 1.50GHz (Processor Number ; 715) 1.60GHz (Processor Number ; 725) 1.70GHz (Processor Number ; 73 5) 1.80GHz (Processor Number ; 745) 2.00GHz (Processor Number ; 7[...]

1 Hardware Overview 1.2 System Block Diagram QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 7 ? Chipset This gate array has the following elements and functions. ? North Bridge (Intel 855PME ( MCH - M, B - step)) ? Pentium - M processor System Bus support ? DRAM Controller : DDR333/DDR266/DDR200 support ? AGP Interface (AGP R2.0, AGP x 4 modes) ?[...]

1.2 System Block Diagram 1 Hardware Overview 1 - 8 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) ? VGA controller ? nVIDIA NV36M ? VRAM 64MB/128MB ? AGP 4x (32bit) ? TMDS ? TV Encoder ? Super I/O (SMSC - made LPC47N2 17) ? Two serial ports (NS16C550 compatible) (1 port is used as Debug port) ? Other main system chips ? PSC (Toshiba - made TMP87PM48U[...]

1 Hardware Overview 1.2 System Block Diagram QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 9 ? LAN (Intel - made ED82562 (Kinnereth) x 1) Control s LAN. Supports 100Base - TX and 10Base - T. ? MODEM (Askey - made 1456VQL4 x 1) S upported by MDC. Uses secondary AC97 line. Data and FAX transmission is available . Supports ITU - TV.90 or .92. The t[...]

1.3 2.5 - inch Hard Disk Drive 1 Hardware Overview 1 - 10 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1.3 2.5 - i nch Hard Disk Drive A compact, high - capacity HDD with a height of 9.5mm. Contains a 2.5 - inch magnetic disk and magnetic heads. Figure 1 - 3 shows a view of the 2 .5 - inch HDD and Tables 1 - 1 and 1 - 2 list the specifications. Fig[...]

1 Hardware Overview 1.3 2.5 - inch Hard Disk Drive QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 11 Table 1 - 1 2.5 - i nch HDD d imensions (2/2) Standard v alue Parameter FUJITSU G8BC000 19610 F UJITSU G8BC000 1C6 10 FUJITSU G8BC000 1HA 10 Width (mm) 70 Outline Height (mm) 9.5 d imensions Depth (mm) 100.0 Weight (g) 99 (MAX)[...]

1.3 2.5 - inch Hard Disk Drive 1 Hardware Overview 1 - 12 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 1 - 2 2.5 - i nch HDD specifications (1/2) Specification (TOSHIBA) Parameter HDD218 9B HDD2194B HDD2188B HDD2191V HDD2A02B HDD2 D 08B Storage size (formatted) 60GB 80GB 100GB Speed (RPM) 4,200 5,400 4,200 5,400 4,200 5,400 Data transfer spee[...]

1 Hardware Overview 1.3 2.5 - inch Hard Disk Drive QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 13 Tabl e 1 - 2 2.5 - i nch HDD specifications (2/2) Specification (FUJITSU) Parameter G8BC000 19610 G8BC000 1C6 10 G8BC000 1HA 10 Storage size (formatted) 60GB 100GB Speed (RPM) 4,200 5,400 4,200 Data transfer speed (Mbits/s) 330.4 554 443.2 Interfa[...]

1.4 Optical Drive 1 Hardware Overview 1 - 14 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1.4 Optical Drive This model equipped with the DVD super multi drive as the optical drive. Some drives support double layer specification. The DVD Super Multi drive accommodates either 12 cm (4.72 - inch) or 8 cm (3.15 - inch) CD, CD - R/RW and DVD. It is a hi[...]

1 Hardware Overview 1.4 Optical Drive QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 15 Table 1 - 4 DVD Super Multi drive s pecifications (1/4) Drive Specification Parameter MATSUSHITA (G8CC000 1S6 10) Read (KB/s) DVD - ROM MAX 8X CAV CD - ROM MAX 24X CAV Write CD - R 16 x (Zone CLV) CD - RW 4X (CLV) H igh S peed CD - RW 8 X (CLV) DVD - R 4 x (Zo[...]

1.4 Optical Drive 1 Hardware Overview 1 - 16 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 1 - 4 DVD Super Multi drive s pecifications (2/4) Dri ve Specification Parameter Matsushita (G8CC00021 6 10) Read (KB/s) DVD - ROM MAX 8X CAV CD - ROM MAX 24X CAV Write CD - R MAX 24 x (Zone CLV) CD - RW 4X (CLV) HSRW MAX 10 X (CLV) U SRW 10 X (CLV) DVD [...]

1 Hardware Overview 1.4 Optical Drive QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 17 Table 1 - 4 DVD Super Multi drive s pecifications (3/4) Drive Specification Parameter Matsushita (G8CC00021611) Supporting Double Layer Read (KB/s) DVD - ROM MAX 8X CAV CD - ROM MAX 24X CAV Write CD - R MAX 24 x (Zone CLV) CD - RW 4X (CLV) HSRW MAX 10 X (CLV) [...]

1.4 Optical Drive 1 Hardware Overview 1 - 18 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 1 - 4 DVD Super Multi drive s pecifications (4/4) Drive Specification Parameter TEAC (G8CC00024611) Supporting Double Layer Read (KB/s) DVD - ROM MAX 8X CAV CD - ROM MAX 24X CAV Write CD - R MAX 24 x (Zone CLV) CD - RW 4X (CLV) HSRW MAX 10 X (CLV) U SRW [...]

1 Hardware Overview 1.5 Keyboard QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 19 1.5 Keyboard A keyboard which consists of 85(US)/86(UK) keys is mounted on the system unit. The keyboard is connected to membrane con nector on the system board and controlled by the keyboard controller. Figure 1 - 5 is a view of the keyboard. Figure 1 - 5 Keyboard[...]

1.6 TFT Col or Display 1 Hardware Overview 1 - 20 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1.6 TFT Color Display The TFT color display is 15.4 inch and consists of LCD module and FL inverter boards. 1.6.1 LCD Module The LCD module used for the TFT color display uses two backlights as the light source and can display a maximum of 262,144 colors [...]

1 Hardware Overview 1.6 TFT Color Display QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 21 1.6.2 F L Inverter Board The FL inverter board supplies a hig h frequency current to illuminate the LCD module FL. Table 1 - 6 lists the FL inverter board specifications. Table 1 - 6 FL inverter b oard s pecifications Specifications Item G71C0004F 3 10 Vol[...]

1.7 Power Supply 1 Hardware Overview 1 - 22 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1.7 Power Supply The power supply supplies twenty - five different voltages to the system board. The power supply microcontroller has the following functions. 1. Judges if the DC p ower supply ( AC adapter ) is connected to the computer . 2. Detects DC output a[...]

1 Hardware Overview 1.7 Power Supply QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 23 Table 1 - 7 Power s upply o utput ratin g (2/2) Pow er supplied ( Yes/No ) Name Voltage [V] Power OFF Suspend mode Power OFF Boot mode No Battery Use USB0PS - E5V 5 Yes No No USB USB 1 PS - E5V 5 Yes No No USB SND - P5V 5 No No No AN12941 A4R7 - P4V 4.7 No No N[...]

1.8 Batteries 1 Hardware Overview 1 - 24 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1.8 Batteries The PC has the following two batteries. ? Main battery ? Real time clock (RTC ) battery Table 1 - 8 lists the specifications for these two batteries. Table 1 - 8 Battery specifications Battery Name Battery Element Output Voltage Capacity G71C0004H210[...]

1 Hardware Overview 1.8 Batteries QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 25 1.8.2 Battery Charging Control B attery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and detects a full charge when the AC adaptor and batte ry are connected to the computer . ? Battery Charge When [...]

1.8 Batteries 1 Hardware Overview 1 - 26 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1.8.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1 - 11 lists the Time require d for charges of RTC battery and data preservation time. Table 1 - 11 Time required for charges of R[...]

1 Hardware Overview 1.9 AC Adapter QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 1 - 27 1.9 AC Adapter The AC adapter is used to charge the battery. Table 1 - 12 lists the AC adapter specifications. Table 1 - 12 AC a dapter s pecifications Parameter Specification ( G71C00024410 ) Power 90W ( Peak 105W) Input voltag e AC 100 to 240V Input frequency 5[...]

1.9 AC Adapter 1 Hardware Overview 1 - 28 QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

Chapter 2 Troubleshooting Procedures[...]

2 Troubleshooting Procedures 2 - ii QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2[...]

2 Troubleshooting Procedures QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - iii Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2 - 1 2.2 Troubleshooting Flowchart .......................................................................................[...]

2 Troubleshooting Procedures 2 - iv QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2.9 Disp lay Troubleshooting .......................................................................................... 2 - 47 Procedure 1 External Monitor Check ....................................................... 2 - 47 Procedure 2 Diagnostic Test Program Executio[...]

2 Troubleshooting Procedures QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - v Figures Figure 2 - 1 Troubleshooting flowchart ............................................................................. 2 - 3 Figure 2 - 2 A set of tool for debug port test ................................................................... 2 - 19 Tables Table 2 - [...]

2 Troubleshooting Procedures 2 - vi QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

2 Troubleshooting Procedures 2.1 Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 1 2 2.1 Troubleshooting Chapter 2 describes how to determine which Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. (The “ FRU ” means the replaceable unit in the field.) The FRUs covered are: 1. Power supply 6. [...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures 2 - 2 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2 - 1 as a guide for determining which troubleshooting procedures to execute. Before going through the flowchart steps, verify the following: ? Ask the user if a password is register[...]

2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 3 Figure 2 - 1 Troubleshooting flowchart (1/2)[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures 2 - 4 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Figure 2 - 1 Troubleshooting flowchart (2/2)[...]

2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 5 If the diagnostics program cann ot detect an error, the problem may be intermittent. The Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an err[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 2 - 6 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2.3 Power Supply Troubleshooting The power supply controller controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. T[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 7 Table 2 - 2 DC IN icon DC IN icon Power supply status Lights green DC power is being supplied from the AC adapter. Blinks orange Power supply malfunction *1 Doesn’t light Any condition other than those above. *1 When the power supply c[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 2 - 8 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Procedure 2 Error Code Check If the power supply microprocessor detects a malfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below. ? Start Off for 2 seconds ? Error code (8 bit) “1” On for one s[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 9 Table 2 - 3 Error code Error code Where err or occurs 1*h DC Power (AC Adapter) 2*h Main battery 3:h 2nd battery 4*h S3V output 5*h 1R5 - C1V output (P61) 6*h 1R5 - C1V output (P62) 7*h PPV output 8*h PTV output 9*h E5V output A*h E3V ou[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 2 - 10 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) ? Main Battery Error code Meaning 21h Main battery charge current is over 12.0A. 22h Main battery discharge current is over 0. 5 A when there is no load. 23h Mai n battery cha rge current is over 3.9 A when AC adapter is not connected. [...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 11 ? 1R5 - C1V output Error code Meaning 60h 1R5 - C1V voltage is over 2.16V when the compu ter is powered on/off . 61h 1R5 - C1V voltage is 1.275V or less when the computer is powered on. 62h 1R5 - C1V voltage is 1.275V or less when the c[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 2 - 12 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) ? E3V output Error code Meaning A 0h E3V voltage is over 3.96 V when the computer is powered o n/off . A 1h E3V voltage is 2.81V or less when the computer is powered on. A 2h E3V voltage is 2.81V or less when the computer is booting up.[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 13 ? 2R5 - B2V output Error code Meaning E 0h 2R5 - B2V voltage is over 3.00 V when the computer is powered on/off . E 1h 2R5 - B2V voltage is 2.125V or less when the compute r is powered on. E 2h 2R5 - B2V voltage is 2.125V or less when t[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 2 - 14 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Procedure 3 Connection Check The wiring diagram related to the power supply is shown below: Any of the connectors m ay be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord are firmly plugged into the [...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 15 Procedure 5 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following C hecks. To disassemble the computer, follow the steps described [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 16 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2.4 System Board Troubleshooting This section describes how to determine if the system board is defective. Start with Procedure 1 and continue with the other procedures as instructed. The procedures described in this section are: Proced[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 17 Procedure 1 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes it. ? If an error message is shown on the[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 18 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) If any other error message displays, perform Check 3. Check 3 The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) through (17), (2 2 ) [...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 19 Procedure 2 Debug Port Check Check the D port status by a debug port test. The tool for debug port test is shown below. Figure 2 - 2 A set o f tool for debug port test The test procedures are follows: 1. Connect the debug test cable to [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 20 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 2 - 4 D ebug port (Boot mode) error status (1/9) D port status Inspection items Details Permission of A20 and Clear of software reset b it Prohibition of APIC I nitialization of MCHM, ICHM Initialization of Super I/O Initializatio[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 21 Table 2 - 4 D ebug port (Boot mode) error status (2/9) D port status Inspection items Details F004h/F005h Saving key scan code Setting TASK_1ms_TSC Controlling fan Enabling system speaker Releasing mute Initializing sound items (for BE [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 22 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 2 - 4 D ebug port (Boot mode) err or status ( 3 /9) D port status Inspection items Details Initialization of MCHM Initialization of ICH4M.D31.Func0 Initialization of ICH4M.D31.Func1 Initialization of USB.Func0,1,2,7 Initial izatio[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 23 Table 2 - 4 D ebug port (Boot mode) error status ( 4 /9) D port status Inspection items Details (F1 03h ) Resume error check S3 recovery error (ICH) Resume error F17AH SM - RAM checksum check Resume error F173H Memory configuration chan[...]

2.4 Sys tem Board Troubleshooting 2 Troubleshooting Procedures 2 - 24 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 2 - 4 D ebug port (Boot mode) error status ( 5 /9) D port status Inspection items Details (F105h) CPU clock measurement Check of param eter block A Permission of SMI except auto - off function Control of excess of rated input pow[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 25 Table 2 - 4 D eb ug port (Boot mode) error status ( 6 /9) D port status Inspection items Details PCI bus initialization (connection of DS Bus) Initialization of LAN information F107h Check of WakeUp factor Task generation for waiting IN[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 26 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 2 - 4 D ebug port (Boot mode) error status ( 7/ 9) D port status Inspection items Details F10Dh INIT_ NDP (Initialization of NDP) Stor ing of CMOS error status to IRT_ERR_STS_BUF CD POWER SW control (for models supporting CD Play [...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 27 Table 2 - 4 D ebug port (Boot mode) error status (8/9) D port status Inspection items Details (F11Ch) (In the case of “ Boot ”) BM loading process (for models supporting fingerprint authentication) Initialization of BM (for models s[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 28 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 2 - 4 D ebug port (Boot mode) error status (9/9) D port status Inspection items Details Initialization of Bluetooth (for models supporting Bluetooth) C heck of existence of target maintenance card Prohibition of unused PC card Set[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 29 Table 2 - 5 Debug port (Suspend mode ) error status (1/3) D port status Inspection items Details Sets the parallel port to D0 sta te (for models supporting printer) F12Fh Release resources used for fingerprint authentication. (For model[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 30 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 2 - 5 Debug port (Suspend mode ) error status (2/3) LED Status Test item Contents Storing CPU register Permission of system area and memory cache ( for high - speed operation ) Suspending of HDD Storing KBC,SCC and MOUSE Storing o[...]

2 Troubleshooting Procedures 2.4 Sy stem Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 31 Table 2 - 5 Debug port (Suspend mode ) error status (3/3) LED Status Test item Contents ( F13Ah) Power LED control during suspending Isolates built - in LAN Makes the power of sound off Makes the power of Dock off ( for models supporti[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 32 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 2 - 6 Debug port (Resume mode ) error status (1/4) LED Status Test item Contents F100h Refer to IRT F101h Refer to IR T F102h Refer to IRT Refer to IRT Clears flag for SMI control. F1 03h Update of Resume counter Checks the W akeU[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 33 Tabl e 2 - 6 Debug port (Resume mode ) error status (2/4) LED Status Test item Contents ( F 122h) AC'97 control Initializing of temperature control information Initializing of KBC VGA display - off and Reset control Initialization [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 34 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table 2 - 6 Debug port (Resume mode ) error stat us s (3/4) LED status Test item Contents Recovery of user alarm setting and cancel of alarm power - on function ( only one time) Enable of power - off switch F125h Initializing EC and sta[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 35 Table 2 - 6 Debug port (Re sume mode ) error status (4/4) LED status Test item Contents (F12Ah) Process related to CPU Setting of CPU clock to SETUP designation Waiting for motor - off of disabled HDD Final decision of USB FDD informati[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2 - 36 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. Thes e tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to perform these t[...]

2 Troubleshooting Procedures 2.5 USB 3.5” FDD Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 37 2 2.5 USB 3.5 ” FDD Troubleshooting This section describes how to determine if the USB 3.5 ” FDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Proc[...]

2.5 USB 3.5” FDD Troubleshooting 2 Troubleshooting Procedures 2 - 38 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the FDD connected to the computer , turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the d[...]

2 Troubleshooting Procedures 2.5 USB 3.5” FDD Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 39 Procedure 3 Connector Check and Replacement Check The USB FDD connector may be disconnected from the system board or SD board . Check visually that the connector is connected to one of them firmly. Check 1 Make sure the following cabl[...]

2.6 2.5” HDD Troub leshooting 2 Troubleshooting Procedures 2 - 40 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) 2.6 2.5 ” HDD Troubleshooting This section describes how to determine if the 2.5 ” HDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with t he other procedures as required. Procedure 1: Pa[...]

2 Troubleshooting Procedures 2.6 2.5” HDD Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 41 Procedure 2 Message Check When the power is turned on, the system perform s the Initial Reliability Test (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. Turn on the computer an[...]

2.6 2.5” HDD Troubleshooting 2 Troubleshooting Procedures 2 - 42 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) Procedure 3 Format Check The computer’s HDD is formatted using the MS - DOS FORMAT program or the physical format program of the test program. To format the HDD, start with Check 1 below and perform the other steps as required. Refer t[...]

2 Troubleshooting Procedures 2.6 2.5” HDD Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 43 Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnostics Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about th[...]

2.6 2.5” HDD T roubleshooting 2 Troubleshooting Procedures 2 - 44 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) Procedure 5 Connector Check and Replacement Check The HDD is connected to the connector of the system board. The connecting portion m ay be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement P[...]

2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 45 2.7 Keyboard Troubleshooting To de termine if the computer’s keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test Pro[...]

2.8 Touch Pad Troubleshooting 2 Troubleshooting Procedures 2 - 46 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) 2.8 Touch Pad Troubleshooting To determine if the computer’s touch pad is functioning properly, perform the following procedures. Start with Pro cedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test[...]

2 Troubleshooting Procedures 2.9 Display Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 47 2.9 Display Troubleshooting This section describes how to determine if the computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External Monitor Check Procedu[...]

2.9 Display Troubleshooting 2 Troubleshooting Procedures 2 - 48 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) Procedure 3 Connector Check and Ca ble Check The LCD m odule is connected to the system board by an LCD/FL cable. The FL inverter board is also connected to the system board by an LCD/FL cable. And the FL is connected to the FL inverter boa[...]

2 Troubleshooting Procedures 2.9 Display Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 49 Procedure 4 Replacement Check The FL lamp , FL inverter, LCD module, system board and LCD/FL cable are connected to display circuits. Any of these components may be damaged. Refer t o Chapter 4, Replacement Procedures, for instructions on ho[...]

2.10 Optical Drive Troubleshooting 2 Troubleshooting Procedures 2 - 50 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) 2.10 Optical Drive Troubleshooting To check if the optical drive is defective or not , follow the troubleshooting pro cedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and [...]

2 Troubleshooting Procedures 2.11 Modem Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 51 2.11 Modem Troubleshooting T o check if the modem is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 : Diagnostic Test Program Execution Check Procedure 2 : Connector Check and Replacement C[...]

2.11 Modem Troubleshooting 2 Troubleshooting Procedures 2 - 52 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) Check 5 The cable between the S D board and system board may be faulty. Replace it with a new one following the instructions in Chapter 4 . If the problem still occurs , perform Check 6. Check 6 The system board may be faulty. Replace it wit[...]

2 Troubleshooting Procedures 2.12 LAN Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 53 2.12 LAN Troubleshooting To check if the computer’s LAN is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 : Diagnostic Test Program Execution Check Procedure 2 : Connector Check and Replace[...]

2.13 Wireless LAN Troubleshooting 2 Troubleshooting Procedures 2 - 54 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) 2.13 Wireless LAN Troubleshooting This section describes how to determine if the computer's Wirel ess LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as requ[...]

2 Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 55 Procedure 2 Antennas' Connection Check The wireless LAN function - wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedu[...]

2.13 Wireless LAN Troubleshooting 2 Troubleshooting Procedures 2 - 56 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) Procedure 3 Replacement Check T he wireless LAN board, wireless LAN antennas or the system board may be damaged. Refer to Chapter 4, Replacemen t Procedures, for instructions on how to disassemble the computer and then check the follo[...]

2 Troubleshooting Procedures 2.14 Sound Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 57 2.14 Sound Troubleshooting To check if the sound function is defective or not , follow the troubleshooting procedures b elow as instructed. Procedure 1 : Diagnostic Test Program Execution Check Procedure 2 : Connector Check Procedure 3 : Repl[...]

2.14 Sound Troubleshooting 2 Troubleshooting Procedures 2 - 58 QOSMIO F 10 Maint enance Manual (960 - 49 8 ) Procedure 3 Replacement Check Che ck 1 When the headphone does not work properly, it may be faulty. Replace it with a new one . If the problem still occurs , perform Check 5. Check 2 When the external microphone does not work properly, it ma[...]

2 Troubleshooting Procedures 2.15 TV Tuner Troubleshooting QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 2 - 59 2.15 TV Tuner Troubleshooting To check if the TV tuner is defective or not , follow the troubleshooting procedures below as instru cted. Procedure 1: Connector Check and Replacement Check Procedure 1 Connector Check and Replacement Check T[...]

2.15 TV Tuner Troubleshooting 2 Troubleshooting Procedures 2 - 60 QOSMIO F 10 Maint enance Manual (960 - 49 8 )[...]

Chapter 3 Tests and Diagnostics[...]

3 - ii QOSMIO F 10 Maintenance Manual (960 - 498 )[...]

QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - iii Chapter 3 Contents 3.1 The Diagnostic Test ...................................................................................................... 3 - 1 3.1.1 Diagnostics menu .................................................................................... 3 - 1 3.1.2 H/W(Hardware) initial info[...]

3 - iv QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.21 Head Cleaning ........................................................................................................... 3 - 47 3.21.1 Function Description ............................................................................. 3 - 47 3.21.2 Operations ..................................[...]

QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - v 3.31.2 Accessing the SETUP Program ............................................................. 3 - 92[...]

3 - vi QOSMIO F 10 Maintenance Manual (960 - 498 ) Tables Table 3 - 1 Subtest names ................................................................................................ 3 - 12 Table 3 - 2 Error codes and error status names ................................................................. 3 - 35 Table 3 - 3 Hard disk controller status re[...]

QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - vii[...]

3 T ests and Diagnostics 3.1 The Diagnostic Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test program s to test the functions of the computer’s hardware modules. The Diagnostics Program s are stored on some Diagnostic Disk s . There are Service Program Modules (DI[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics 3 - 2 QOSMIO F 10 Maintenance Manual (960 - 498 ) ? HARD DISK TEST ? REAL TIMER TEST ? NDP TEST ? EXPANSION TEST ? CD - ROM /DVD - ROM TEST Other tests are: ? Wireless LAN TEST (Wireless LAN TES T disk) ? LAN/M odem / Bluetooth/IEEE1394 TEST (LAN/M odem / Bluetooth/IEEE1394 TEST disk) ? Sound TEST (So[...]

3 T ests and Diagnostics 3.1 The Diagnostic Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 3 3.1.2 H/W (Hard w are) i nitial information setting tool The H/W initial information setting tool consists of the following programs. ? Initial configuration ? Region write ? System configuration display ? E2PROM test (MAC/ GUID/ DMI) You will need th[...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3 - 4 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.2 Executing the Diagnostic Test T o start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the floppy disk drive. 2. Release the lock of the power switch and turn on the computer with pressing the F12 . Select t[...]

3 T ests and Diagnostics 3.2 Executing the Diagnostic Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 5 NOTE : To exit the DIAGNOSTIC TEST MENU, p ress Esc . If a test program is in progress, press Ctrl + Break to exit the test program. If a test program is in progress, press Ctrl + C to stop the test program. Set the highlight bar to 1 , and [...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3 - 6 QOSMIO F 10 Maintenance Manual (960 - 498 ) Select the option you want to execute and press Enter . When you select 1- SYSTEM TEST , the following message will appear: SYSTEM TEST NAME XXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] ; test end [Ctrl]+[C] ; key stop SUB-TEST : XX PA[...]

3 T ests and Diagnostics 3.2 Executing the Diagnostic Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 7 Selecting YES of ERR OR STOP stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below: ERROR STATUS NAME [[ HALT OPERATION ]] 1: Test end 2: Continue 3: Retry These[...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3 - 8 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.2.3 Heatrun test program Heatrun test starts executing the same subtests as RUNNING TEST . For more detail s on this test, refer to the section 3.4.[...]

3 T ests and Diagnostics 3.3 Setting of the hardware configuration QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 9 3.3 Setting of the hardware configuration To execute this program, select 2-Repair initial config set in the startup menu, press Enter and follow the directions on the screen. The H/W initial information setting tool c onsists of fol[...]

3.3 Setting of the hardware configuration 3 Tests and Diagnostics 3 - 10 QOSMIO F 10 Maintenance Manual (960 - 498 ) ? Setting of the HWSC ? Setting of the UUID ? Display of the DMI information (including UUID) ? Setting of DVD region code (Yes/No) After completion of the above settings, H/W configuration & DMI information are appeared in order[...]

3 T ests and Diagnostics 3.3 Setting of the hardware configuration QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 11 Subtest 08 System configuration display This subtest displays the information of the system configuration. When the following message appears, confirm the contents and press Enter . Press [Enter] key For more details o n the system [...]

3.4 Heatrun Test 3 Tests and Diagnostics 3 - 12 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.4 Heatrun Test To execute this program, select 3-Repair heatrun in the sta rtup menu and press Enter . After selecting this test, the same subtests as 3.23 Running Test are executed successively. For more details on the procedure and test content, refer to[...]

3 T ests and Diagnostics 3.5 Subtest Names QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 13 3.5 Subtest Names Table 3 - 1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Tab le 3 - 1 Subtest names (1/2) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 03 04 05 ROM checksum Fan ON/OFF Geyserville Quick charge DMI re[...]

3.5 Subtest Names 3 Tests and Diagnostics 3 - 14 QOSMIO F 10 Maintenance Manual (960 - 498 ) Table 3 - 1 Subtest names (2/ 2 ) No. Test Name Subtest No. Subtest Name 6 PRINTER [Not supported] 01 02 03 Ripple pattern Function Wrap around 7 A SYNC [Not supported] 01 02 03 FIR/SIR Point to point (send) FIR/SIR Point to point (receive) Wrap around (boa[...]

3 T ests and Diagnostics 3.6 System Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 15 3.6 System Test To execute the System Test , select 1 from the DIAGNOSTIC TEST MENU , press Enter and follow the directions on the screen. Move the highlight bar to the subtest yo u want to execute and press Enter . Subtest 01 ROM Checksum This subtest execu[...]

3.6 System Test 3 Tests and Diagnostics 3 - 16 QOSMIO F 10 Maintenance Manual (960 - 498 ) After a while, the fan rotating will stop. Subtest 0 3 Geyserville If the CPU supports Gerserville (SpeedStep), this Subtest checks that the CPU operating clock speed can be changed. Subtest 0 4 Quick Charge This subtest check s the status for the quick charg[...]

3 Tests and Diagnostics 3.7 Memory Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 17 3.7 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Conventional memory This subtest wr[...]

3.8 Keyboard Test 3 Tests and Diagnostics 3 - 18 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.8 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Pressed key code display When[...]

3 Tests and Diagnostics 3.9 Display Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 19 3.9 Display Test To ex ecute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 VRAM read/write for VGA This su[...]

3.9 Display Test 3 Tests and Diagnostics 3 - 20 QOSMIO F 10 Maintenance Manual (960 - 498 ) Subtest 04 Gradation & Mode test fo r VGA This subtest displays gradations for following mode s . To change the mo de, press Enter . [Mode 12] [Mode 13] [Mode 3] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600 16M] [...]

3 Tests and Diagnostics 3.9 Display Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 21 Subtest 06 “H” Pattern Display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHH[...]

3.10 Floppy Disk Test 3 Tests and Diagnostics 3 - 22 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.10 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD because t he contents of the floppy disk will be erased. To execute the Floppy Disk Tes[...]

3 Tests and Diagnostics 3.10 Floppy Disk Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 23 Select the number of the subtest you want to execute and press Enter . The following message will appear during the floppy disk test. FLOPPY DISK IN PROGRESS XXXXXXX xxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX[...]

3.11 Printer Test 3 Tests and Diagnostics 3 - 24 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.11 Printer Test CAUTION : Printer Test is not supported for this model. To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE : A n IBM compatible printer must be connected to the sy[...]

3 Tests and Diagnostics 3.11 Printer Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 25 Subtest 02 Function This subtest is for IBM compatible printers , and tests the following functions: Normal print Double - width print Compr essed print Emphasized print Double - strike print All characters print This subtest prints the various print types [...]

3.12 Async Test 3 Tests and Diagnostics 3 - 26 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.12 Async Test CAUTION : Async Test is not supported for this model. To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. Move the highlight bar to the subtest you want to execute a[...]

3 Tests and Diagnostics 3.13 Hard Disk Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 27 3.13 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter , and follow the directions on the screen. CAUTION : The contents of the hard disk will be erased when subtest 02, 03, 04, 06, 0 8 or 09 is executed. Be[...]

3.13 Hard Disk Test 3 Tests and Diagnostics 3 - 28 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter. The following message will appear during each subtest. HARD DISK TEST XXXXXXX XXX DIAGNOSTIC TES[...]

3 Tests and Diagnostics 3.13 Hard Disk Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 29 Subt est 04 Cross t alk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder and then reads the data while moving from cylinder to cylinder. (Test the data interference in the neighbor track) Worst pattern da[...]

3 Tests and Diagnostics 3.14 Real Timer Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 29 3 3.14 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Real time A new dat[...]

3.14 Real Timer Test 3 Tests and Diagnostics 3 - 30 QOSMIO F 10 Maintenance Manual (960 - 498 ) Then the subtest reads and compares this data with the original data.[...]

3 Tests and Diagnostics 3.14 Real Timer Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 31 Subtest 03 Real t ime carry CAUTION : When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments . M ak e sure the date and time are displayed in the following format: Current date : 12-31-1999[...]

3.15 NDP Test 3 Tests and Diagnostics 3 - 32 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.15 NDP Test To execute the NDP test, se lect 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 NDP This test checks the following functions of NDP: ? Control word ? Status word ? Bus ? Addition ? Multiplication[...]

3 Tests and Diagnostics 3.16 Expansion Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 33 3.16 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wraparound NOTE: : PCMCIA wraparound test is not supported for this model. NOTE: To execute[...]

3.16 Expansion Test 3 Tests and Diagnostics 3 - 34 QOSMIO F 10 Maintenance Manual (960 - 498 ) Subtest 02 RGB monitor ID NOTE: To execute this subtest, an external monitor with monitor ID function is required. Connect the exter nal monitor to the PC for the test of ID acquisition. The judgment of acquisition is based on the panel data. In simultane[...]

3 Tests and Diagnostics 3.17 CD - ROM/DVD - ROM Test QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 35 3.17 CD - ROM/DVD - ROM Test To execute the CD - ROM/DVD - ROM test, select 13 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE : For the subtest 01, 02 and 03 , use the TOSHIBA CD - ROM TEST DISK TDY - 01[...]

3.18 Error Code and Error Status Names 3 Tests and Diagnostics 3 - 36 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.18 Error Code and Error Status Names Table 3 - 2 lists the error codes and error status names for the Diagnostic Test. Table 3 - 2 Error codes and error status names (1/3) Device name Error code E rror status name (Common) FF Data Com[...]

3 Tests and Diagnostics 3.18 Error Code and Error S tatus Names QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 37 Table 3 - 2 Error codes and error status names (2/3) Device name Error code Error sta tus name FDD 01 02 03 04 08 09 10 20 40 80 60 06 EE FDD - BAD COMMAND ERROR FDD - ADDRESS MARK NOT FOUND FDD - WRITE PROTECTED FDD - RECORD NOT FOUND[...]

3.18 Error Code and Error Status Names 3 Tests and Diagnostics 3 - 38 QOSMIO F 10 Maintenance Manual (960 - 498 ) Table 3 - 2 Error codes and error status names (3/3) Device name Error code Error status name (HDD) CC E0 0A EE DA 12 HDD - WRITE FAULT HDD - STATUS ERROR HDD - BAD SECTOR HDD - ACCESS TIME ERROR HDD - NO HDD HDD - DMA CRC ERROR NDP 01 [...]

3 Tests and Diagnostics 3.19 Hard Disk Test Detail Status QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 39 3.19 Hard Disk Test Detail Sta tus When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an eight - digit numbe[...]

3.19 Hard Disk Test Detail Status 3 Tests and Diagnostics 3 - 40 QOSMIO F 10 Maintenance Manual (960 - 498 ) Table 3 - 4 Error register contents Bit Name Description 7 BBK (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error. “1” … Uncorrectable [...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 41 3.20 ONLY ONE TEST 3.20.1 Program Description This program test s the unique functions of this model. 3.20.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter . The following menu appears in the display. ####################################[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics 3 - 42 QOSMIO F 10 Maintenance Manual (960 - 498 ) Subtest 01 Pressed key display When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding k ey on the screen changes to the key character that was pressed. Holding a key down enable[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 43 Subtest 0 2 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Direction and parameter B) Switching function check. This test displays the response from the touch pad and touch pad switch. W hen moving your finger on the touch [...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics 3 - 44 QOSMIO F 10 Maintenance Manual (960 - 498 ) Subtest 0 3 GP Button This subtest checks if the AV buttons (10 buttons) work properly. The following message appears in the display. Press button [0] Press the AV button from the left ( the AV button nearest to power button). The name of AV buttons in the[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 45 Slide the switch to OFF position. Then, the following message appears in the display. KILL SWITCH ON !! Slide the switch to ON position. Then, the following message appears in the display. KILL SWITCH OFF !! After Sliding the switch to OFF position, the sc[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics 3 - 46 QOSMIO F 10 Maintenance Manual (960 - 498 ) P ress 9 and Enter to return to ONLY ONE TESST menu.[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 47 Sub test 0 6 Touch Pad (Scroll Button) This subtest checks if the scroll button of touch pad works properly. The following message appears in the display. ****** Scroll button TEST (VX.XX) ****** Press Scroll button Up Button xxx Down Button xxx Press [ESC[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics 3 - 48 QOSMIO F 10 Maintenance Manual (960 - 498 ) P ress Enter and following message appears in the display. Check [PowerSW-LED]= Green Check if the Power Switch LED lights in the following order. (Green - > Orange - > Blue - > OFF) Press any key and the following message appears in th e display.[...]

3 Tests and Diagnostics 3.21 Head Cleaning QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 49 3.21 Head C leaning 3.21.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.21.2 Operations 1. Selecting test 4 from the DIAGN[...]

3.22 Log Utilities 3 Tests and Diagnostics 3 - 50 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.22 Log Utilities 3.22.1 Function Description This function logs error information generated while a test is in progress and s tores the results in RAM. This function can store data on a floppy disk , or output the data to a printer or the display . The e[...]

3 Tests and Diagnostics 3.22 Log Utilities QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 51 3.22.2 Operations 1. Select 5 and press Enter in the DIAGNOS TIC MENU, t he error information is displayed in the following format: XXXXX ERRORS CNT TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] 001 FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROTECTED[...]

3.23 Running Test 3 Tests and Diagnostics 3 - 52 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.23 Running Test 3.23.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02, 0 6 ) 3. Display test (subtest 01) 4. Real timer test (subtest 02) 5. HDD test ([...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 53 3.24 Floppy Disk Drive Utilities 3.24.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is only for testing a floppy disk drive. It [...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics 3 - 54 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.24.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2. FORMAT program (a) Selecting FORMAT [...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 55 3. COPY program (a) When COPY is selected, the following mess age appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a message similar to the one below: Insert sourc[...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics 3 - 56 QOSMIO F 10 Maintenance Manual (960 - 498 ) 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If 2:HDD is selected, the display will go to step (h). [...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 57 (k) The following message will appear . To finish the dump, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear . Select ing 2 returns to the FDD UTILITIES MENU. Another dump (1:Yes,2:No) ? 5. HDD ID READ p[...]

3.25 System Configuration 3 Tests and Diagnostics 3 - 56 QOSMIO F 10 Maint enance Manual (960 - 498 ) 3 3.25 System Configuration 3.25.1 Function Description NOTE : To display the system configuration, the write protect tab should be OFF position. If the tab is ON position, move the tab to OFF position and restart the test. Otherwise the correct in[...]

3 Tests and Diagnostics 3.25 System Configuration QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 57 3.25.2 Operations Select 8 from the DIAGNOSTIC MENU and press Enter . Then, the following syste m configuration appears in the display. System Configuration Display : Ver X.XX [Machine Name ???] * - Processor Type = XXXXXX-XXXXXMHz Code = XX L2 Cach[...]

3.26 Wireless LAN Test Program (Intel - made b/g) 3 Tests and Diagnostics 3 - 58 QOSMIO F 10 Maint enance Manual (960 - 498 ) 3.26 Wireless LAN Test Program (Intel - made b/g) This section de scribes how to perform the wireless LAN transmitting - receiving test (Intel - made Calexico 802.11b/g) . To execute the wireless LAN t est, use the Diagnosti[...]

3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Intel - made b/g) QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 59 When a defective is detected in the test , following typical cause is considered. ? Bad connection of wireless LAN card ? Using a wrong wireless LAN card (Using unspecified card) ? Defective wireless LAN card Check the connec[...]

3.26 Wireless LAN Test Program (Intel - made b/g) 3 Tests and Diagnostics 3 - 60 QOSMIO F 10 Maint enance Manual (960 - 498 ) Subtest03 Antenna check & communication test of 11b mode Caution: To execute subtest 03 - 05, u se another computer (with C alexico wireless LAN card) that can communicate by the wireless LAN as a responder machine. Acce[...]

3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Intel - made b/g) QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 61 ? Defective wireless LAN card Check the connection and condition, and execute the subtest again. Subtest0 4 Communication test of 11g mode This subt est checks the communication of wireless LAN antenna of Calexico 802.11g mod[...]

3.27 Wireless LAN Test Program (Intel - made a/b/g) 3 Tests and Diagnostics 3 - 62 QOSMIO F 10 Maint enance Manual (960 - 498 ) 3.27 Wireless LAN Test Program (Intel - made a/b/g) This section describes how to perform the wireless LAN transmitting - receiving test (Intel - made Calexico 802.11a/b/g) . To execute the wireless LAN t est, use the Diag[...]

3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel - made a/b/g) QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 63 Press any key to return to the test menu.[...]

3.27 Wireless LAN Test Program (Intel - made a/b/g) 3 Tests and Diagnostics 3 - 64 QOSMIO F 10 Maint enance Manual (960 - 498 ) If a defective is found during the test, NG message will appear in the display. Press any key and following message will appear in the display . ************************************************************* * * * SKU NG !![...]

3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel - made a/b/g) QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 65 Press any key to return to the test menu. When a defective is detected in the test , following typical cause is considered. ? Bad connection of wir eless LAN card ? Defective wireless LAN card ? Disappearance of MAC address[...]

3.27 Wireless LAN Test Program (Intel - ma de a/b/g) 3 Tests and Diagnostics 3 - 66 QOSMIO F 10 Maint enance Manual (960 - 498 ) * * ************************************************************* Press any key to return to the test menu . When a defective is detected in the test , following typical cause is considered. ? Bad connection of wireless L[...]

3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel - made a/b/g) QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 67 Check the connection and condition, and execute the subtest again.[...]

3.27 Wireless LAN Test Program (Intel - made a/b/g) 3 Tests and Diagnostics 3 - 68 QOSMIO F 10 Maint enance Manual (960 - 498 ) Subtest0 5 Communication test of 11 g mode This subtest checks the communication of wireless LAN antenna of Calexico 802.11g mode. For more details on procedure and contents of this subtest, refer to Subtest04 Communicatio[...]

3 Tests and Diagnostics 3.28 Wireless LAN Test Program (Askey - made) QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 69 3.28 Wi reless LAN Test Program (Askey - made) This section describes how to perform the wireless LAN transmitting - receiving test (Askey - made Atheros b/g, a/b/g) . Caution: To execute subtest 03 - 07, u se another computer (w[...]

3.28 Wireless LAN Test Program (Askey - made) 3 Tests and Diagnostics 3 - 70 QOSMIO F 10 Maint enance Manual (960 - 498 ) 4. When the program disk 2 starts, following menu will appear in the display. To execute the subte st, press test number and Enter . ******************************************************* * Atheros MB4x(MB44ag/43g) Maintenance [...]

3 Tests and Diagnostics 3.28 Wireless LAN Test Program (Askey - made) QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 71 Subtest02 MAC Address Check This subtest reads out the MAC address of the card installed and confirms if it is valid. When the MAC address is valid one, following message will appear in the display. ******************************[...]

3.28 Wireless LAN Test Program (Askey - made) 3 Tests and Diagnostics 3 - 72 QOSMIO F 10 Maint enance Manual (960 - 498 ) Moreover , following typical cause is considered. ? B a d connection of wireless LAN card ? Bad connection of wir eless LAN antenna cable (Main/Aux) ? Environment for wireless LAN communication (Interference/ obstruction) ? Defe[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 73 3.29 LAN/Modem /Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem /Bluetooth/IEEE1394 test with the test program. Insert the t est program disk for LAN/Modem /Bluetooth/IEEE1394 test in FDD and [...]

3.29 LAN/Modem/Bl uetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3 - 74 QOSMIO F 10 Maint enance Manual (960 - 498 ) Subtest0 1 ( i82562 + ICHx ) This subtest checks the operation of m ini - PCI I/F by the loopback test in the chip . The following mess age will appear: [LAN transmit & receive test !] COMPLETED Repeat count = 00000 Error [...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 75 Subtest0 2 ( GbE ) CAUTION : Gigabit Ethernet (GbE) test is not supported for this model. This subtest checks the operation of m ini - PCI I/F by the loopback test in the chip . Select 2 to execute and press Enter . The followin[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3 - 76 QOSMIO F 10 Maint enance Manual (960 - 498 ) 3.29.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “ FAT - MODE inspection device (p roduct code: QE2000P01 made by Nitto Electric Manufacture Co.,Ltd ) ” for the [...]

3 Test s and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 77 3.29.3 Bluetooth test CAUTION : Bluetooth test is not supported for this model. T o execute this test, input 3 and press Enter . Note : U se another computer that can communicate by the Bluetooth as a reference machine to perfo[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3 - 78 QOSMIO F 10 Maint enance Manual (960 - 498 ) Subtest0 1 BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter . The following message will appear: ------------------------------------[...]

3 Test s and Diagnostics 3.29 LAN/Modem/Bluetooth/IEE E1394 Test Program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 79 If the target machine has any problem, it displays Error messasge . The following message is displayed. ---------------------------------------------------------------------------- - Bluetooth Subsystem T&D for PCSE(BD_ADD[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3 - 80 QOSMIO F 10 Maint enance Manual (960 - 498 ) If the machine detects a malfunction, it indic ates the error code as shown below. The error code begins with the least significant digit. Error code Table 3 - 6 Error code for Bluetooth test (BD_ADDR) (1/2) Error code Meaning [...]

3 Test s and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 81 Table 3 - 6 Error code for Bluetooth test (BD_ADDR) (2 /2 ) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Trans action Collision. 0x24 LMP PDU N[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3 - 82 QOSMIO F 10 Maint enance Manual (960 - 498 ) ---------------------------------------------------------------------------- - Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Co. ------------------------------------------------------------------[...]

3 Test s and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 83 ---------------------------------------------------------------------------- - Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Co. ------------------------------------------------------------------[...]

3.29 LAN/Mo dem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3 - 84 QOSMIO F 10 Maint enance Manual (960 - 498 ) A> If any problem is detected during the test, the massage FAIL is displayed on the tester machine with the error code as shown below. The error code begins with the least significant digit. Error code Table 3 - 7 Error cod[...]

3 Test s and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 85 Table 3 - 7 Error code for Bluetooth test (BD_ADDR of the DUT) (2 /2 ) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collision. 0x24[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3 - 86 QOSMIO F 10 Maint enance Manual (960 - 498 ) 3.29.4 IEEE1394 test T o execute this test, input 4 and press Enter . N OTE : Use another computer that can communicate by IEEE1394 (i. Link) cable as a re sponder machine to perform this test. The following menu will appear: *[...]

3.30 Sound Test program 3 Tests and Diagnostics QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 85 3 Tests and Diagnostics 3.30 Sound Test program This section describes how to perform the Sound test . To execute the sound test, refer to the following description. Insert the t est program disk for Sound test in the floppy disk drive and turn on the[...]

3.30 Sound Test program 3 Tests and Diagnostics 3 - 86 QOSMIO F 10 Maintenance Manual (960 - 498 ) To return to the Sound test menu, Press 9 and Enter . T hen following message will appear in the display. *********************************** ******** May I Restart ? ******* *********************************** Press any key to continue… After press[...]

3 Tests and Diagnostics 3.30 Sound Test program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 87 Subtest0 2 Sine Wave This subtest is executed by loading the COM fil e (ADSIN.COM). The program expands sin e wave data table from 16KB to 64KB, and creates the play data. Then it transfers the data between the DMA and the CODEC to play the sine wave.[...]

3.30 Sound Test program 3 Tests and Diagnostics 3 - 88 QOSMIO F 10 Maintenance Manual (960 - 498 ) 3.30.3 CD Sound (Standard) test To execute the CD Sound (Standard) test , press 3 and En ter . Insert the test media (TOSHIBA TEST CD - ROM or ABEX TEST CD - ROM) or music CD on the market (if the test media can not be prepared). The menu appears in t[...]

3 Tests and Diagnostics 3.30 Sound Test program QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 89 Press any key to stop the narration . Then the test returns to the CD Sound (Standard) test menu. Subtest0 2 English Narration When selecting this subtest, narration in English starts. For more details on the procedure, refer to the subtest01. Subtest[...]

3.30 Sound Test p rogram 3 Tests and Diagnostics 3 - 90 QOSMIO F 10 Maintenance Manual (960 - 498 ) (2) Audio CD Insert an audio CD and the following menu appears in the display. CD/DVD TEST IN PROGRESS XXXXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] ; test end [Ctrl]+[C] ; key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT: XXXXX WRITE DA[...]

3 Tests and Diagnostics 3.31 SETUP QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 91 CAUTION : Sound (Legacy) test is not supported in this model. 3.31 SETUP 3.31.1 Function Description This program displays the current system setup information as listed below: 1. Memory 2. System Date/Time 3. Battery 4. Password 5. Boo t Priority (a) Boot Priorit[...]

3.31 SETUP 3 Tests and Diagnostics 3 - 92 QOSMIO F 10 Maintenance Manual (960 - 498 ) (b) H ard Disk Mode 12. LEGACY EMULATION (a) USB KB/Mouse Legacy Emulation (b) USB - FDD Legacy Emulation 13. PCI LAN[...]

3 Tests and Diagnostics 3.31 SETUP QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 93 3.31.2 Accessing the SETUP Program While pressing ES C , turn on the power. Then press F1 . The fo llowing display appears. NOTE : *1 This message appears only on the model for TCL (Canada).[...]

3.31 SETUP 3 Tests and Diagnostics 3 - 94 QOSMIO F 10 Maintenance Manual (960 - 498 ) Moving Within the SETUP Menu and Changing Values 1. Press ? an d ? to move between the two columns. Press ? and ? to move between items in a column. Press Fn + ? ?? PgUp ) and Fn + ? ?? PgD n) to move between the two pages. 2. Press either the S pace bar or Back S[...]

3 Tests and Diagnostics 3.31 SETUP QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 95 SETUP Options The SETUP screen is divided into 13 functionally related groups. This sectio n describes each group and its options. 1. Memory This group of option s displays the computer’s memory. This field displays the total amount of memory installed and is au[...]

3.31 SETUP 3 Tests and Diagnostics 3 - 96 QOSMIO F 10 Maintenance Manual (960 - 498 ) NOTE: Display of the LCD Brightness will be changed in the condition below: (*1) Operating the battery (*2) Using the AC adapter User Setting Use this option to set the battery save parameters on the sub - window, BATTERY SAVE OPTIONS . Battery Save Options Proces[...]

3 Tests and Diagnostics 3.31 SETUP QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 97 HDD Auto Off Use this option to set the duration of the HDD automatic power off function. xx Min. Automatically turns off the power to the hard disk drive if it is not used for the duration set. The duration xx can be set to 1 , 3 , 5 , 10 , 15 , 20 or 30 minutes.[...]

3.31 SETUP 3 Tests and Diagnostics 3 - 98 QOSMIO F 10 Maintenance Manual (960 - 498 ) 4. Password This option sets or resets the user password for power on and instant security ( Fn+F1 ). Registered The user password has been registered. Not r egistered The user password has not been registered. For details on setting the user password , refer to t[...]

3 Tests and Diagnostics 3.31 SETUP QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 99 (a) Power On Display This option is used to select the display when booting up. Auto - Selected Selects an e xternal monitor if one is connected. Otherwise it selects the internal LCD. (Default) LCD+AnalogRGB Selects both the internal LCD and the external monitor [...]

3.31 SETUP 3 Tests and Diagnostics 3 - 100 QOSMIO F 10 Maintenance Manual (960 - 498 ) 7. Others Whether o r not you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) CPU Cache Use this option to enable or disable the CPU cache. Enabled Enables the CPU cache. (Default) Disabled D[...]

3 Tests and Diagnostics 3.31 SETUP QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 101 Set the parameters for the Auto Power On (automatic power on) function in the “ OPTIONS ” window. To set the time, use Spa ce bar or BackSpace . Press ? to move the cursor to the right and ? to move the cursor to the left when you set the date and time. For t[...]

3.31 SETUP 3 Tests and Diagnostics 3 - 102 QOSMIO F 10 Maintenance Manual (960 - 498 ) Mode 1 Sets to Mode1. (Default) Glows blue (P ower ON) / Glows yellow (Stan d by) / Glows orange (Power OFF/Hibernation) Mode 2 Sets to Mode 2. Glows blue (Power ON) / Alternately flashes green and orange (Stan d by) / Alternately flashes green and blue (Power OF[...]

3 Tests and Diagnostics 3.31 SETUP QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 103 This option displays the interr upt level for the Card Bus in the computer . It is for information only and cannot be changed. PCI BUS = IRQ10, IRQ11[...]

3.31 SETUP 3 Tests and Diagnostics 3 - 104 QOSMIO F 10 Maintenance Manual (960 - 498 ) 11. Peripheral Use this option to select the peripheral's mode. (a) Internal Pointing Device This option enables or disables the touch pad Enable d Enables the touch pad . (Default) Disabled Disables the touch pad . (b) Hard Disk Mode Use this option to sele[...]

3 Tests and Diagnostics 3.31 SETUP QOSMIO F 10 Maintenance Manual (960 - 498 ) 3 - 105 13. PCI LAN This option sets the Enable / Disable of the built - in LAN functions. Enabled Enables built - in LA N functions. (Default) Disabled Disables built - in LAN functions.[...]

3.31 SETUP 3 Tests and Diagnostics 3 - 106 QOSMIO F 10 Maintenance Manual (960 - 498 )[...]

Chapter 4 Replacement Procedures[...]

4 Re placement Procedures 4 - ii QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 4[...]

4 Replacement Procedures QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 4 - iii Chapter 4 Contents 4.1 Overview .................................................................................................................... 4 - 1 Safety Precautions ................................................................................................ 4[...]

4 Re placement Procedures 4 - iv QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 4.14.2 Guide ..................................................................................................... 4 - 42 4.15 He at sink/ CPU .......................................................................................................... 4 - 44 4.16 VGA Heat s[...]

4 Replacement Procedures QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 4 - v Figure s Figure 4 - 1 Removing the battery pack ................................................................................. 4 - 8 Figure 4 - 2 Removing the PC card ..................................................................................... 4 - 10 Figure 4 - [...]

4 Re placement Procedures 4 - vi QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Figure 4 - 30 Applying silicon grease .................................................................................... 4 - 46 Figure 4 - 31 Removing the VGA heat sink .......................................................................... 4 - 47 Figure 4 - 32 Remov[...]

4 Replacement Procedures 4.1 Overview QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 1 4 4.1 Overview This chapter describes the procedure for removing and replacing the field replaceable units (FRUs) in the PC . It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FRUs must be[...]

4.1 Overview 4 Replacement Procedures 4 - 2 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Safety Precautions Please read the following safety ins tructions before disassembling the computer and always follow the instructions while working on the computer. D ANGER : 1. In the case of the battery, always use authentic parts or equivalent parts approved[...]

4 Replacement Procedures 4.1 Overview QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 3 Before You Begin Take note of the following points before star ting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “ 4.2.1 Battery Pack ” . 1. [...]

4.1 Overview 4 Replacement Procedures 4 - 4 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Disassembly Procedure Three main types of cable connector are used. ? Pressure plate connector ? Spring connector ? Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and[...]

4 Replacement Procedures 4.1 Overview QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 5 Assembly Procedure After the computer has been disassembled and the part that caused the fault has been repaired or replaced, the computer must be reassembled. Take note of the following general points when a ssembling the computer. ? Take your time and follow [...]

4.1 Overview 4 Replacement Procedures 4 - 6 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Screw Tightening T orque Use the following torque when tightening screws. CAUT ION : Overtightening may damage screw s or part s . Undertightening may allow screw s to loosen (and possibly fall out) causing a short circuit or other damage. NOTE : To tighten scre[...]

4 Replacement Procedures 4.1 Overview QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 7 Screw Notation To make maintenance of the computer easier, markings of the kinds of the screws including the types an d lengths of the screws are indicated on the computer body. Format: Screw shape + Screw length (mm) Screw shape B: Bind screw F: Thin head scre[...]

4.2 Battery pack/PC card/Bridge Media 4 Replacement Procedures 4 - 8 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.2 Battery pack/PC card/Bridge Media 4.2.1 Battery pack Removing the battery pack The following describes the procedure for removing the battery pack (See Figure 4 - 1). CAUTION: Take care not to short circuit the terminals when removin[...]

4 Replacement Procedures 4.2 Battery pack/PC card/Bridge Media QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 9 NOTE : Dispose of the used battery pack in accordance with the laws and ordinances of your local authority. Installing the battery pack The following describes the procedure for r einstalling the battery pack (See Figure 4 - 1). CAUTION[...]

4.2 Battery pack /PC card/Bridge Media 4 Replacement Procedures 4 - 10 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.2.2 PC card Removing the PC card The following describes the procedure for removing the PC card (See Figure 4 - 2). CAUTIO N: Insert or remove the PC card in accordance with any instructions in the PC card manual or the manual s of t[...]

4 Replacement Procedures 4.2 Battery pack/PC card/Bridge Media QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 11 4.2.3 Bridge Media (SD Card / Memory Stick / xDPicture Card/Multi Media Card) Removing the Bridge media The following describes the procedure for removing the bridge media ( See Figure 4 - 3). CAUTION: Insert or remove the Bridge Media[...]

4.3 HDD 4 Replacement Procedures 4 - 12 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.3 HDD Removing th e HDD The following describes the procedure for removing the HDD ( See Figure 4 - 4 and 4 - 5). CAUTION: Be careful not to drop or leave screws in the PC. Take care not to press on the top or bottom of the HDD . Pressure may cause data loss or da[...]

4 Replacement Procedures 4.3 HDD QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 13 4. Remove the following screws fixing the HDD assembly . ? F3 ? 4S FLAT BIND screw x4 5. Detach the HDD holder from the HDD . 6. Pull out the lamina te cover to the arrow direction and detach it from the HDD. Figure 4 - 5 Removing the HDD HDD F3 ? 4S FLAT BIND HDD [...]

4.3 HDD 4 Replacement Procedures 4 - 14 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Installing the HDD The following describes the procedure for installing an HDD ( See Figure 4 - 4 and 4 - 5). 1. Attach the laminate cover to the HDD. 2. Install the HDD to the HDD holder and secure them with the following screws . ? F3 ? 4S FLAT BIND screw x4 NOTE:[...]

4 Replacement Procedures 4.4 Memory module QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 15 4.4 Memory module CAUTION: The power of the computer must be turned off when you remove the memory module. Removing a memory module with the power on risks damaging the module or the computer itself. Do not touch the memory modul e terminals. Any dirt on [...]

4.4 Memo ry module 4 Replacement Procedures 4 - 16 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Install ing the memory module To install the memory module, confirm that the computer is in boot mode . T hen perform the following procedure (See Figure 4 - 6). 1. Insert the memory module into the connector of the computer slantw ise (terminal side firs[...]

4 Replacement Procedures 4.5 Keyboard/Bluetooth QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 17 4.5 Keyboard/Bluetooth 4.5.1 Keyboard Removing the keyboard The following describes the procedure for removing the keyboard (See Figure 4 - 7 to 4 - 9). CAUTION: As the keytop may fall out, when handling the keyboard always hold it by the frame and d[...]

4.5 Keyboard/Bluetooth 4 Replacement Procedures 4 - 18 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 5. Remove the following screws fixing the keyboard ? M2.5 ? 2. 8B FLAT BIND screw x2 Figure 4 - 8 Removing the keybo ard 6. Lift the upper side of the keyboard and turn it face down on the palm rest. M2.5x2.8B FLAT BIND[...]

4 Replacement Procedures 4.5 Keyboard/Bluetooth QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 19 7. Remove the following screws fixing the keyboard support plate . ? M2 .5 ? 2.8B FLAT BIND screw x2 8. Remove the keyboard support plate . Figure 4 - 9 Removing the keyboard support plate 9. Pull out the keyboard flexible cable from the slit and dis[...]

4.5 Keyboard/Bluetooth 4 Replacement Procedures 4 - 20 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Installing the k eyboard The following describes the procedure for installing the keyboard (See Figure 4 - 7 to 4 - 9). 1. Turn the keyboard upside down and place it on the palm rest as its face down . Connect the keyboard flexible cable to the connec[...]

4 Replacement Procedures 4.5 Keyboard/Bluetooth QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 21 4.5.2 Bluetooth Removing the Bluetooth The following describes the procedure for removing the bluetooth (See Figure 4 - 10). 1. Disconnect the bluetooth flat cable from the connector CN44 00 on the system board. 2. Turn up the insulator to take out t[...]

4.6 Switch membrane 4 Replacement Procedures 4 - 22 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.6 Switch membrane Removing the switch membrane The following describes the procedure for removing the switch membrane (See Figure 4 - 11). 1. Remove the fo llowing screw and remove the LCD CON holder . ? M2.5 ? 6B FLAT BIND screw x1 2. Disconnect the s[...]

4 Replacement Procedures 4.6 Switch membrane QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 23 Installing the switch membrane The following describes the procedure for installing the switch membrane (See Figure 4 - 11). 1. Connect the switch membrane to the connector CN9650 on the system board. 2. Slide the switch membrane to install and secure i[...]

4.7 Optical drive 4 Replacement Procedures 4 - 24 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.7 Optical drive NOTE : Do not apply excessive force to the top of an optical drive. Do not touch the shaded portion of the figure below, when you remove or install the drive. Removing the optical drive The following describes the procedure for removing t[...]

4 Replacement Procedures 4.7 Optical drive QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 25 3. Remove t he following screws to remove the side bracket from the optical drive. ? M2 ? 3C SUPER THIN HEAD screw x 2 ? M2 ? 3.2 Stepping screw x1 Figure 4 - 13 Disassembling the side bracket Installing the optical drive The following describes the proce[...]

4.8 Display assem bly 4 Replacement Procedures 4 - 26 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.8 Display assembly Removing the display assembly The following describes the procedure for removing the display assembly (See Figure 4 - 14 to 4 - 18). 1. Close the display and turn the computer upside down. 2. R emove the following screws from the b[...]

4 Replacement Procedures 4.8 Display assembly QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 27 3. Tun over the computer and open the display. 4. Remove the following screws and remove the harness cover . ? M2.5 ? 6B FLAT BIND screw x2 ? M2.5 ? 10B FLAT BIND screw x 1 Figure 4 - 15 Removing the screws (front) M2.5 ? 6B FLAT BIND M2.5 ? 10B FLAT B[...]

4.8 Display assembly 4 Replacement Procedures 4 - 28 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 5. Disconnect the LCD harness from the connector PJ 5600 on the system board. 6. Unlock the connector CN3201 and disconnect the touch pad cable from the connector on the system board. 7. Unlock the connector CN9550 and disconnect the SJ board flat cable[...]

4 Replacement Procedures 4.8 Display assembly QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 29 9. Lift up the display assembly from the Optical drive side first to unhook the latches. 10. Remove the disp lay assembly from the base assembly and place it next to the base assembly. 11. Remove the following screws and remove the wireless LAN cover o[...]

4.8 Display assembly 4 Replacement Procedures 4 - 30 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 12. Disconnect the wireless LAN antenna cables from the wireless LAN board. Figure 4 - 18 Removing the wirel ess LAN antenna cables Wireless LAN antenna cable Aux (black) Wireless LAN antenna cable Main (white)[...]

4 Replacement Procedures 4.8 Display assembly QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 31 Installing the display assembly The following describes the procedure for installing the display assembly ( See Figure 4 - 14 to 4 - 18). 1. Connect the wireless LAN antenna cables (Main (white cable) and Aux (black cable)) to the connector s on the wi[...]

4.9 SD board/MDC 4 Replacement Procedures 4 - 32 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.9 SD board/MDC 4.9.1 SD board Removing the SD board The following describes the procedure for removing the SD board ( See Figure 4 - 19). 1. Disconnect the SD board flat cable from the connector CN9510 on the SD board. 2. Disconnect the SVP harness from t[...]

4 Replacement Procedures 4.9 SD board/MDC QOSM IO F10 Maintenance Manual (960 - 49 8 ) 4 - 33 Figure 4 - 19 Removing the SD board Installing the SD board The following describes the procedure for installing the SD board (See Figure 4 - 19). 1. Install the RJ11 connector and its core to each slot of the base assembly. 2. Install the SD board and sec[...]

4.9 SD board/MDC 4 Replacement Procedures 4 - 34 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.9.2 MDC Removing the MDC The following describes the procedure for removing the MDC ( See Figure 4 - 20). 1. Turn over the SD board. 2. Remove the fol lowing screws fixing the MDC and pull the MDC straight up from the connector CN3000 on the SD board. ? M[...]

4 Replacement Procedures 4.10 Fan QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 35 4 4.10 Fan Removing the fan The following describes the procedure for removing the fan ( See Figure 4 - 21). 1. Disconnect the fan cable from the CN8770 on the system board. 2. Remove the following screws and remove the fan . ? M2.5 ? 4B FLAT BIND screw x2 Figure [...]

4.11 Wireless LAN board 4 Replacement Procedures 4 - 36 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.11 Wireless LAN board Removing the wireless LAN bo ard The fol lowing describes the procedure for removing the wireless LAN board ( See Figure 4 - 22). 1. Open the left and right latches holding the wireless LAN board and remove it. Figure 4 - 22 R[...]

4 Replacement Procedures 4.12 System board QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 37 4.12 System board CAUTION: 1. When handling the system board, always hold by the edges. Do not touch the printed circuit face . 2. If replacing with a new system board, execute the subtest01 I nitial configuration in section 3.3 “ Setting of the hardwar[...]

4.12 System board 4 Replacement Procedures 4 - 38 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Figure 4 - 24 Removing t he system board M2.5x4B FLAT BIND BATT CONN cover Insulator DC - IN jack Wireless LAN KILL switch M2.5x4B FLAT BIND USB harness SVP harness SD board flat cable[...]

4 Replacement Procedures 4.12 System board QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 39 Installing the system board The following describes the procedure for installing the system board ( See Figure 4 - 23 and 4 - 24). 1. Connect the DC - IN jack, SD board flat cable and SVP harness to the system board. 2. Install t he BATT CONN cover with f[...]

4.13 RTC battery 4 Replacement Procedures 4 - 40 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.13 RTC battery Removing the RTC battery The following describes the procedure for removing the RTC battery (See Figure 4 - 25). 1. Disconnect the RTC battery harness from the connector CN8490 on the system board. 2. Pull out the RTC battery harness fro m [...]

4 Replacement Procedures 4.14 TV tuner module/Guide QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 41 4.14 TV tuner module/Guide 4.14.1 TV tuner module Removing the TV tuner module The following describes the procedure for removing the TV tuner module ( See Figure 4 - 26). 1. Disconnect the TV tuner harness from the connector on the TV tuner modu[...]

4.14 TV tuner module/Guide 4 Replacement Procedures 4 - 42 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Installing the TV tuner module The following describes the procedure for installing the TV tuner module ( See Figure 4 - 26). 1. Insert the TV tuner module terminals slantwise into the connector on the system board and secure it with the following[...]

4 Replacement Procedures 4.14 TV tuner module/Guide QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 43 Figure 4 - 27 Removing the guide Installing the guide The following describes the procedure for installing the guide ( See Figure 4 - 27). 1. Install the guide on the system board and secure it with the following screw . ? M2 ? 4Z BIND screw x1 2[...]

4.15 Heat sink/CPU 4 Replacement Procedures 4 - 44 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.15 Heat sink/ CPU Removing the heat sink/ CPU The following describes the procedure for removing the heat sink and CPU ( See Figure 4 - 28 and 4 - 29). 1. After Removing the following screws, remove the heat sink holder and heat sink . ? M2 ? 4Z BIND sc[...]

4 Replacement Procedures 4.15 Heat sink/CPU QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 45 2. Unlock the CPU by rotating the cam on the CPU socket 180 degrees to the counter clockwise with a flat - blade screwdriver. 3. Remove the CPU. Figure 4 - 29 Removing the CPU Installing the heat sink /CPU The following describes the procedure for instal[...]

4.15 Heat sink/CPU 4 Replacement Procedures 4 - 46 QOSMIO F10 Maintenance Manual (960 - 49 8 ) NOTE: Apply t he silicon grease enough to cover the chip surface using the special applicator. Figure 4 - 30 Applying silicon grease 5. Install the heat sink and heat sink holde r and secure them with the following screws in the order of numbers marked on[...]

4 Replacement Procedures 4.16 VGA Heat sink QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 47 4.16 VGA Heat sink Removing the VGA heat sink The following describes the procedure for removing the VGA heat sink ( See Figure 4 - 31). 1. Afte r removing the following screws, remove the VGA heat sink . ? M2 ? 4Z BIND screw x3 Figure 4 - 31 Removing th[...]

4.17 PC card cover 4 Replacement Procedures 4 - 48 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.17 PC card cover Removing the PC card cover The following describes the procedure for removing the PC card cover (See Figure 4 - 32). 1. Remove the following screws securing the PC card cover. ? M2 ? 3 Z BIND screw x2 2. Open the PC card cover toward th[...]

4 Replacement Procedures 4.18 Speaker/VGA fan QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 49 4.18 Speaker/VGA fan Removing the Speaker/VGA fan The following describes the procedure for removing the speaker and VGA fan ( See Figure 4 - 33). 1. Pull out the speaker cable L (red cable) under the insulator and the glass tapes. 2. Remove the speake[...]

4.18 Speaker/VGA fan 4 Replacement Procedures 4 - 50 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Installing the Speaker/VGA fan The following describes the procedure for installing the speaker and VGA fan (See Figure 4 - 33). NOTE: When inst alling speakers, make sure they are fit to the guides closely by pressing them from the top. Pass the VGA fa[...]

4 Replacement Procedures 4.19 Battery latch QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 51 4.19 Battery latch Removing the battery latch The following describes the procedure for removing the battery latch ( See Figure 4 - 34 and 3 - 35). 1. Remove the following screws fixing the battery latch assembly. ? M2 ? 4Z FLAT BIND screw x2 2. Slide th[...]

4.19 Battery latch 4 Replacement Procedures 4 - 52 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Installing the battery latch The following describes the procedure for installing the battery latch ( See F igure 4 - 34 and 4 - 35). 1. Install the battery lock button . 2. Set the spring on the battery latch and install the battery latch on the battery [...]

4 Replacement Procedures 4.20 Touch pad QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 53 4.20 Touch pad Removing the touch pad The following de scribes the procedure for removing the touch pad ( See Figure 4 - 36). 1. Remove the glass tape fixing the touch pad flexible cable. 2. Disconnect the touch pad flat cable from the touch pad. 3. Remove t[...]

4.20 Touch pad 4 Replacement Procedures 4 - 54 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Installing the touch pad The following describes the procedure for installing the touch pad ( See Figure 4 - 36). NOTE : Do not reuse the touch pad so that it can not be used after peeling off from the computer. Be sure to s tick a new touch pad. 1. Stick the[...]

4 Replacement Procedures 4.21 SJ board QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 55 4.21 SJ board Removing the SJ board The following describes the procedure for removing the SJ board ( See Figure 4 - 37). 1. Disconnect the microphone cable from the connector CN6000 on the SJ board. 2. Unlock th e connector CN9560 on the SJ board and disconn[...]

4.21 SJ board 4 Replacement Procedures 4 - 56 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Installing the SJ board The following describes the procedure for installing the SJ board (See Fig ure 4 - 37). 1. Pass through the SJ board flat cable into the slit of the middle frame and arrange it along the guide on the insulator. Secure the SJ board flat [...]

4 Replacement Procedures 4.22 Microphone QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 57 4.22 Microphone Removing the microphone The following describes the procedure for removing the microphone ( Se e Figure 4 - 38). 1. Remove the following screw to remove the microphone hold guide from the base assembly. ? M2 ? 4Z BIND screw x1 2. Detach the [...]

4.23 LCD unit/FL inverter 4 Replacement Procedures 4 - 58 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 4.23 LCD unit/FL inverter Removing the LCD unit / FL inverter The following describes the pr ocedure for removing the LCD unit and FL inverter (See Figure 4 - 39 to 4 - 42). 1. Open widely the display panel and pull up both the hinge caps to remove[...]

4 Replacement Procedures 4.23 LCD unit/FL inverter QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 59 4. Remove the following screw fixing the FL inverter. ? M2x4Z SUPER THIN HEAD screw x1 5. (for model with wireless LAN or Bluetooth) Pull out one insulator and peel off the other one adhe red to the FL inverter. 6. Disconnect the LCD harness es fr[...]

4.23 LCD unit/FL inverter 4 Replacement Procedures 4 - 60 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 9. Remove the following screws fixing the LCD unit. ? M2x4Z SUPER THIN HEAD screw x4 10. With the bottom edge of the LCD unit on the displ ay cover, lift only the top edge of the LCD unit. After peeling off the aluminum tape , d isconnect the LCD h[...]

4 Replacement Procedures 4.23 LCD unit/FL inverter QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 61 11. Remove the following screws to remove the right and left LCD supports from the LCD unit. ? M2x3C SUPER THIN HEAD screw x4 Figure 4 - 42 Removing the LCD supports M2x3C SUPER THIN HEAD M2x3C SUPER THIN HEAD LCD supports[...]

4.23 LCD unit/FL inverter 4 Replacement Procedures 4 - 62 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Installing the LCD u nit/FL Inverter The following describes the procedure for installing the LCD unit and FL inverter (See Figure 4 - 39 to 4 - 42). 1. Secure the LCD supports (left and right) to the LCD uni t with the following screws . ? M2 ? 3C[...]

4 Replacement Procedures 4.24 Wireless antennas/ LCD harness QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 63 4.24 Wireless antennas/ LCD harness 4.24.1 W ireless antenna s Removing the w ireless antenna s The following describes the procedure for removing the wireless antennas (See Figure 4 - 44 and 4 - 44). 1. Make sure the wireless LAN antenn[...]

4.24 Wireless antennas/ LCD harness 4 Replacement Procedures 4 - 64 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 3. Peel off the glass tapes fixing the wireless LAN antenna cables and bluetooth antenna cable and peel off the wireless LAN antennas and bluetooth anten na from the display cover. Figure 4 - 44 Removing the wireless antennas Installing t[...]

4 Replacement Procedures 4.24 Wireless antennas/ LCD harness QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 65 4.24.2 LCD harness Removing the LCD harness The following describes the procedure for removing LCD harness (See Figure 4 - 45 and 4 - 46). 1. Remove the following screw securing the LCD harness holder and remove the LCD harness holder (d[...]

4.24 Wireless antennas/ LCD harness 4 Replacement Procedures 4 - 66 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 2. Remove the following screw securing the LCD harness holder and remove the LCD harness holder (middle frame side). ? M2. 5 ? 2.8B FLAT BIND screw x1 3. Remove the LCD harness from the guide. Figure 4 - 46 Removing the LCD harness holder[...]

4 Replacement Procedures 4.25 Hinge QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 67 4.25 Hinge Removing the Hinge The following describes the procedure for removing hinge (See Figure 4 - 47 to 4 - 49). 1. Remove the following screws securing the display cover and detach the display cover . ? M2. 5 ? 6 PSP TIGHT screw x4 Figure 4 - 47 Removing t[...]

4.25 Hinge 4 Replacement Procedures 4 - 68 QOSMIO F10 Maintenance Manual (960 - 49 8 ) 2. Remove the following screws and remove the hinges (display cover side). ? M2. 5 ? 6B FLAT BIND screw x2 (Locktight) Figure 4 - 48 Removing the hinge (display cover side) 3. Remove the following screws and remove the hinges (middle frame side). ? M2. 5 ? 4B FLA[...]

4 Replacement Procedures 4.25 Hinge QOSMIO F10 Maintenanc e Manual (960 - 49 8 ) 4 - 69 Installing the Hinge The following describes the procedure for installing the hinge (See F igure 4 - 47 to 4 - 49). 1. Install the hinges (middle frame side) on the back side of the middle frame and secure them with the following screws . ? M2. 5 ? 4B FLAT BIND [...]

4.26 Fluorescent lamp 4 Replacement Procedures 4 - 70 QOSMIO F10 Maintenance Manual (960 - 49 8) 4 4.26 Fluorescent lamp This system uses the following LCD module. Type Part No. Supplier Section 15.4 inch (W - XGA) G33C000 2A110 Samsung 4.2 6 . 1 NOTE : - When working with a LCD module, always use a flat, grounded table . - Handle the backlight uni[...]

4 Replacement Procedures 4.26 Fluorescent lamp QOSMIO F10 Maintenance Manual (960 - 49 8) 4 - 71 4.26.1 R eplacing the 15.4 - inch (W - XGA) Samsung f luorescent lamp Removing the 15.4 - inch W - XGA Samsung fluorescent lamp To remove the 15.4 - inch W - XGA Samsung Fluorescent Lamp , follow the steps below and refer to Figures 4 - 50 to 4 - 54. Th[...]

4.26 Fluorescent lamp 4 Replacement Procedures 4 - 72 QOSMIO F10 Maintenance Manual (960 - 49 8) 2. Remove aluminum tapes stuck on the right and left sides. Figure 4 - 48 Replacing Sharp fluorescent lamp (W - XGA) (2) 3. Remove the lamp wire tape and the aluminum tape stuck on the bottom. Figure 4 - 49 Replacing Sharp fluorescent lamp (W - XGA) (3)[...]

4 Replacement Procedures 4.26 Fluorescent lamp QOSMIO F10 Maintenance Manual (960 - 49 8) 4 - 73 4. Unlatch the hooks on the bottom first and then the hooks on the right and left sides to remove the top chassis from the middle frame. Figure 4 - 50 Replacing Sharp fluorescent lamp (W - XGA) (4) Top chassi s Middle frame Hook[...]

4.26 Fluorescent lamp 4 Replacement Procedures 4 - 74 QOSMIO F10 Maintenance Manual (960 - 49 8) 5. Remove the p anel assembly from the backlight unit. CAUTION: Be careful not to damage the COF and ICs when removing the panel assembly. Figure 4 - 51 Replacing Sharp fluorescent lamp ( W- XGA) (6) Assembling the 15.4 - inch W - XGA Samsung fluorescen[...]

Appendices[...]

Appendices App - ii QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

Appendices QOSMIO F 10 Maintenance Manual (960 - 49 8 ) App - iii Appendix Contents Appendix A Handling the LCD Module .......................................................................... A - 1 Appendix B Board Layout ................................................................................................ B - 1 B.1 System Board Front [...]

Appendices App - iv QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 18 CN4200 1394 I/F connector ( 4 - pin) .......................................................... C - 10 C. 19 IS2101 MEDIA BRIDGE I/F connector ( 42 - pin) ................................... C - 10 C. 20 CN 1400 Memory connector A ( 200 - pin) ...................................[...]

Appendices QOSMIO F 10 Maintenance Manual (960 - 49 8 ) App - v Appendix D Keyboard Scan/Character Codes .............................................................. D - 1 Appendix E Key Layout .................................................................................................... E - 1 E.1 Keyboard Layout ...........................[...]

Appendices App - vi QOSMIO F 10 Maintenance Manual (960 - 49 8 ) F igures Figure B - 1 System b oard layout (front) ........................................................................... B - 1 Figure B - 2 System b oard layout (back) ........................................................................... B - 3 Figure B - 3 SD b oard layout[...]

Appendices QOSMIO F 10 Maintenance Manual (960 - 49 8 ) App - vii Table C - 10 USB connector 0 (port 0) ( 4 - pin) .................................................................. C - 6 Table C - 11 USB I/F Relay connector ( 8 - pin) .................................................................. C - 7 Table C - 12 USB connector 1 (port 2) ( 4[...]

Appendices App - viii QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table C - 42 TV - tuner connector ( 12 - pin) ....................................................................... C - 29 Table C - 43 SVP connector ( 14 - pin) .............................................................................. C - 29 Table C - 44 Internal Microph one[...]

QOSMIO F 10 Maintenance Manual (960 - 498) A - 1 Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cove r, be sure to seat it so that it[...]

Appendix A Handling the LCD Module A - 2 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agen t. Apply the agent to a c[...]

Appendix A Handling the LCD Module QOSMIO F 10 Maintenance Manual (960 - 49 8 ) A - 3 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS - LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle [...]

Appendix A Handling the LCD Module A - 4 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not d[...]

Appendix A Handling the LCD Module QOSMIO F 10 Maintenance Manual (960 - 49 8 ) A - 5 10. If you transport the module , do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization.[...]

Appendix A Handling the LCD Module A - 6 QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

QOSMIO F 10 Ma intenance Manual (960 - 49 8 ) B - 1 Appendix B Appendix B Board Layout B.1 System Board Front View Figure B - 1 System b oard layout (front) (a) (b) (c) (d) (e) (f) (h) (i) (j) (k) (l) (m) (g) (n) (o) (p)[...]

B.1 System Board Front View Appendix B Board Layout B - 2 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Table B - 1 System b oard ICs and connectors (front ) Mark Number Name ( a ) CN5801 TV Input connector ( b ) CN9500 SD board I/F connector ( c ) CN9650 SWITCH I/F connector ( d ) CN3230 Keyboard I/F connector ( e ) CN3201 PAD I/F connector (f) CN22[...]

Appendix B Board Layout B.2 System Board Back View QOSMIO F 10 Maintenance Manual (960 - 49 8 ) B - 3 B.2 System Board Back View Figure B - 2 System b oard layout ( b ack) (a) (b) (c) (d) (e) (f) (g) (q) (h) (i) (j) (k) (l) (m) (n) (o) (p) (r)[...]

B.2 System Board Back View Appendix B Board Layout B - 4 QOSMIO F10 Maintenance Manual (960 - 49 8 ) Table B - 2 System board ICs and connectors ( back ) Mark Number Name ( a ) CN8810 1st battery connector ( b ) CN8490 RTC battery connector ( c ) CN1820 ODD I/F connector (d) CN8800 DC IN connector (e) IC5800 SVP MEM I/F (f) CN5502 D - video I/F con[...]

Appendix B Board Layout B.3 SD Board Front View QOSMIO F 10 Maintenance Manual (960 - 49 8 ) B - 5 B.3 SD Board Front View Figure B - 3 SD b oard layout (front) Table B - 3 SD board connectors ( front ) Mark Number Name ( a ) CN4621 USB I/F connector ( b ) CN4620 USB I/F relay connector ( c ) CN6003 Speaker (right) connector (d) CN6002 Speaker (lef[...]

B.4 SD Board Back View Appendix B Board Layout B - 6 QOSMIO F10 Maintenance Manual (960 - 49 8 ) B.4 SD Board Back View Figure B - 4 SD b oard layout ( back ) Table B - 4 SD board connectors ( back ) Mark Number Name ( a ) CN3000 MDC I/F connector (a)[...]

Appendix B Board Layout B.5 SJ Board Front View QOSMIO F 10 Maintenance Manual (960 - 49 8 ) B - 7 B.5 SJ Board Front View Figure B - 5 SJ b oard layout ( front) Table B - 5 SJ board connectors ( front ) Mark Number Name ( a ) DS6000 Headphone connector ( b ) J 6001 External Microphone I/F connector (a) (b)[...]

B.6 SJ Board Back View Appendix B Board Layout B - 8 QOSMIO F10 Maintenance Manual (960 - 49 8 ) B.6 SJ Board Back View Figure B - 6 SJ b oard layout ( back ) Table B - 6 SJ board connectors ( back ) Mark Number Name ( a ) CN6000 Internal microphone connector ( b ) CN9560 SD board I/F connector (a) (b)[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 1 Appendix C Appendix C Pin Assignment System Board (FCLSY*) C. 1 CN1800 HDD I/F connector ( 44 - pin) Table C - 1 HDD I/F connector ( 44 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 IDRSTA - P5N I/O 2 G ND - 3 PDD07 - P3P I/O 4 PDD08 - P3P I/O 5 PDD06 - P3P I/O 6 PDD09 - P3P I/O 7 PDD05 [...]

C.2 CN1820 ODD I/F connector (50 - pin) Appendix C Pin Assignment C - 2 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 2 CN1820 ODD I/F connector ( 50 - pin) Table C - 2 ODD I/F connector ( 50 - pin) PIN No. Signal name I/O PIN No. Si gnal name I/O 1 CDAUDL - PXP I 2 CDAUDR - PXP I 3 CD - GND I 4 N.C - 5 IDRSTB - P5N O 6 SDD08 - P3P I/O 7 SDD07 - [...]

Appendix C Pin Assignment C.3 CN2110 PC card I/F connector (70 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 3 C. 3 CN2110 PC card I/F connector ( 70 - pin) Table C - 3 PC card I/F connector ( 70 - pin) (1/2) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND - 2 ACAD00 - EYP I/O 3 ACAD01 - EYP I/O 4 ACAD03 - EYP I/O 5 ACAD05 - EYP I/O[...]

C.4 CN3230 Keyboard I/F connector (34 - pin) Appendix C Pin Assignment C - 4 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table C - 3 PC card I/F connector ( 70 - pin) (2/2) PIN No. Signal name I/O PIN No. Signal name I/O 51 MCVCCA - EYV I 52 MCVPPA - EYV I/O 53 ACTRDY - EYN I/O 54 ACFRAM - EYN I/O 55 ACAD17 - EYP I/O 56 ACAD19 - EYP I/O 57 ACVS2 -[...]

Appendix C Pin Assignment C.5 CN4400 Bluetooth I/F con nector (20 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 5 C. 5 CN4400 Bluetooth I/F connector ( 20 - pin) Table C - 5 Bluetooth I/F connector ( 20 - pin) PIN No. Signal na me I/O PIN No. Signal name I/O 1 GND - 2 N.C. - 3 BTMDL - P3N O 4 N.C. - 5 N.C. - 6 N.C. - 7 N.C. - 8 BTRST - S3[...]

C.8 CN8770 FAN connector (3 - pin) Appendix C Pin Assignment C - 6 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 8 CN8770 FAN connector ( 3 - pin) Table C - 8 FAN connector ( 3 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 FAN VCC I 2 GND - 3 FANG0 - P3P I C. 9 CN8780 FAN connector (for VGA) ( 3 - pin) Table C - 9 FAN connector (for VG[...]

Appendix C Pin Assignment C.11 CN4612 USB I/F Relay connector (8 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 7 C. 11 CN4612 USB I/F Relay connector ( 8 - pin) Table C - 11 USB I/F Relay connector ( 8 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 USB1PS - E5V I 2 USB1PS - E5V I 3 USBP4 - S3N I/O 4 USBP4 - S3P I/O 5 GND - 6 GND[...]

C.15 CN9500 Sound board I/F connector (50 - pin) Appendix C Pin Assignment C - 8 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 15 CN95 00 Sound board I/F connector ( 50 - pin) Table C - 15 Sound board I/F connector ( 50 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 CD - GND - 2 CDAUDL - PXP I 3 CD - GND - 4 CDAUDR - PXP I/O 5 CD - GND [...]

Appendix C Pin Assignment C.16 CN9650 SWITCH I/F connector (20 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 9 C. 16 CN9650 SWITCH I/F connector ( 20 - pin) Table C - 16 SWITCH I/F connector ( 20 - pin) PIN No. Signal name I/O PIN No. Signal nam e I/O 1 PBLEDO - S3P I 2 M5V - 3 PBLEDB - S3P I 4 PBLEDG - S3P I 5 PWRSW - S3N I 6 TVBTN - S3N[...]

C.18 CN4200 1394 I/F connector (4 - pin) Appendix C Pin Assignment C - 10 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 18 CN4200 1394 I/F connector ( 4 - pin) Table C - 18 1394 I/F connector ( 4 - pin) PIN N o. Signal name I/O PIN No. Signal name I/O 1 TPB0 - E3N I/O 2 TPB0 - E3P I/O 3 TPA0 - E3N I/O 4 TPA0 - E3P I/O C. 19 IS2101 MEDIA BRIDGE I/[...]

Appendix C Pin Assignment C.20 CN1400 Memory connector A (200 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 11 C. 20 CN 1400 Memory connector A ( 200 - pin) Table C - 20 Memory connector A ( 200 - pin) (1/3) PIN No. Signal name I/O PIN No. Signal name I/O 1 MR1R25 - B1V - 2 MRVREF - B1V - 3 GND - 4 GND - 5 SDQ00 - B2P I/O 6 SDQ06 - B2P I/[...]

C.20 CN1400 Memory connector A (200 - pin) Appendix C Pin Assignment C - 12 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table C - 20 Memory connector A ( 200 - pin) (2/3) PIN No. Signal name I/O PIN No. Signal name I/O 65 SDQ26 - B2P I/O 66 SDQ30 - B2P I/O 67 SDQ27 - B2P I/O 68 SDQ31 - B2P I/O 69 2R5 - B2V - 70 2R5 - B2V - 71 SCB5A - B2P I/O 72 SC[...]

Appendix C Pin Assignment C.20 CN1400 Memory connector A (200 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 13 Table C - 20 Memory connector A ( 200 - pin) (3/3) PIN No. Signal name I/O PIN No. Signal name I/O 135 SDQ34 - B2P I/O 136 SDQ39 - B2P I/O 137 GND - 138 GND - 139 SDQ38 - B2P I/O 140 SDQ35 - B2P I/O 141 SDQ44 - B2P I/O 142 SDQ41 [...]

C.21 CN1401 Memory connector B (200 - pin) Appendix C Pin Assignment C - 14 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 21 CN 140 1 Memory connector B ( 200 - pin ) Table C - 21 Memory connector B ( 200 - pin) (1/3) PIN No. Signal name I/O PIN No. Signal name I/O 1 MRVREF - B1V - 2 MRVREF - B1V - 3 GND - 4 GND - 5 SDQ00 - B2P I/O 6 SDQ06 - B2P [...]

Appendix C Pin Assignment C.21 CN1401 Memory connector B (200 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 15 Table C - 21 Memory connector B ( 200 - pin) (2/3) PIN No. Signal name I/O PIN No. Signal name I/O 63 GND - 64 GND - 65 SDQ26 - B2P I/O 66 SDQ30 - B2P I/O 67 SDQ27 - B2P I/O 68 SDQ31 - B2P I/O 69 2R5 - B2V - 70 2R5 - B2V - 71 SCB[...]

C.21 CN1401 Memory connector B (200 - pin) Appendix C Pin Assignment C - 16 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table C - 21 Memory connector B ( 200 - pin) (3/3) PIN No. Signal name I/O PIN No. Signal name I/O 135 SDQ34 - B2P I/O 136 SDQ39 - B2P I/O 137 GN D - 138 GND - 139 SDQ38 - B2P I/O 140 SDQ35 - B2P I/O 141 SDQ44 - B2P I/O 142 SDQ41[...]

Appendix C Pin Assignment C.22 CN2200 Mini PCI I/F connector (124 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 17 C. 22 CN2200 Mini PCI I/F con nector ( 124 - pin) Table C - 22 Mini PCI I/F connector ( 124 - pin) (1/2) PIN No. Signal name I/O PIN No. Signal name I/O 1 N.C. - 2 N.C. - 3 N.C. - 4 N.C. - 5 N.C. - 6 N.C. - 7 N.C. - 8 N.C. - [...]

C.22 CN2200 Mini PCI I/F connector (124 - pin) Appendix C Pin Assignment C - 18 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table C - 22 Mini PCI I/F connector ( 124 - pin) (2/2) PIN No. Signal name I/O PIN No. Signal name I/O 61 IRDY - P3N I/O 62 GND - 63 P3V - 64 FRAME - P3N I /O 65 CLKRUN - P3N I /O 66 T RD Y - P3N I /O 67 SERR - P3N I 68 STOP [...]

Appendix C Pin Assignment C.23 CN2400 WW Tuner I/F connector (124 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 19 C. 23 CN2400 WW Tuner I/F connector ( 124 - pin) Table C - 23 WW Tuner I/F connector ( 124 - pin) (1/2) PIN No. Signal name I/O PIN No . Signal name I/O 1 N.C. - 2 N.C. - 3 N.C. - 4 N.C. - 5 N.C. - 6 N.C. - 7 N.C. - 8 N.C. - [...]

C.23 CN2400 WW Tuner I/F connector (124 - pin) Appendix C Pin Assignment C - 20 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table C - 23 WW Tuner I/F connector ( 124 - pin) (2/2) PIN No. Signal name I/O PIN No. Signal name I/O 63 T - P3V - 64 FRAME - P3N I /O 65 CLKRUN - P3N I/O 66 T RD Y - P3N I /O 67 SERR - P3N I 68 STOP - P3N I/O 69 GND - 70 T [...]

Appendix C Pin Assignment C.24 CN3201 PAD I/F connector (4 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 21 C. 24 CN3201 PAD I/F connector ( 4 - pin) Table C - 24 PAD I/F connector ( 4 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND - 2 IPDCLK - P5P I/O 3 IPDDAT - P5P I/O 4 GND - C. 25 PJ 5600 LCD I/F connector ( 41 - pin) Ta[...]

C.26 CN5080 CRT I/F connector (15 - pin) Appendix C Pin Assignment C - 22 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 26 CN5080 CRT I/F connector (15 - pin) Table C - 26 CRT I/F connector ( 15 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 CRTRED - PXP I 2 CRTGRN - PXP I 3 CRTBLU - PXP I 4 N.C - 5 GND - 6 GND - 7 GND - 8 GND - 9 DDC -[...]

Appendix C Pin Assignment C.29 CN5502 D - video I/F connector (14 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 23 C. 29 CN5502 D - video I/F connector (14 - pin) T able C - 29 D - video I/F connector (14 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 HDTVY - PXP I 2 GND - 3 HDTVPB - PXP I 4 GND - 5 HDTVPR - PXP I 6 GND - 7 LINO[...]

C.31 CN3000 MDC I/F connector (30 - pin) Appendix C Pin Assignment C - 24 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) SD Board ( F CLSD*) C. 31 CN3000 MDC I/F connector ( 30 - pin) Table C - 31 MDC I/F connector ( 30 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 N.C - 2 GND - 3 GND - 4 N.C - 5 N.C - 6 N.C - 7 N.C - 8 GND - 9 N.C - 10 N.[...]

Appendix C Pin Assignment C.33 CN4621 USB I/F connec tor (port 4) (4 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 25 C. 33 CN4621 USB I/F connector (port 4) ( 4 - pin) T able C - 33 USB I/F connector (port 4) ( 4 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 (USBV) - 2 (D - 0) I/O 3 (D+0) I/O 4 GND - C. 34 CN6002 Speaker (left[...]

C.36 CN9550 Sound jack board I/F connector (21 - pin) Appendix C Pin Assignment C - 26 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 36 CN9550 Sound jack board I/F connector ( 21 - pin) Table C - 36 Sound jack board I/F connector ( 21 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 VREF1 - P2V I 2 MICIN - PXP I 3 LOUTL - PXP I 4 A - GND [...]

Appendix C Pin Assignment C.37 CN9510 System boar d I/F connector (50 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 27 C. 37 CN9510 System board I/F connector ( 50 - pin) Table C - 37 System boar d I/F connector ( 50 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 SPKON - P3N - 2 VOLBYP - P3N I/O 3 FMTST0 - P3P I 4 SVSDA - P3P I/[...]

C.38 J2410 TV Antenna connector (4 - pin) Appendix C Pin Assignment C - 28 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C. 38 J2410 TV Antenna connector ( 4 - pin) Table C - 38 TV antenna connector ( 4 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 (CN9611 - 3) I/O 2 (CN9611 - 1) I/O 3 (CN9611 - 2) I/O 4 (CN9611 - 4) I/O C. 39 CN2410 Coax[...]

Appendix C Pin Assignment C.42 CN9614 TV - tuner connector (12 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 29 C. 42 C N9614 TV - tuner connector ( 12 - pin) Table C - 42 TV - tuner connector ( 12 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 TV - GND - 2 LINL - PXP I 3 TV - GND - 4 LINR - PXP I 5 TV - GND - 6 COMP01 - PXP I 7[...]

C.44 CN6000 Internal Microphone I/F connector (2 - pin) Appendix C Pin Assignment C - 30 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) SJ board (FCLSJ*) C. 44 CN6000 Internal Microphone I/F connector ( 2 - pin) Table C - 44 Internal Microphone I/F connector ( 2 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 (VREF1 - P2V) I 2 A - GND - C. 4[...]

Appendix C Pin Assignment C.47 CN9560 Sound board I/F connector (21 - pin) QOSMIO F 10 Maintenance Manual (960 - 49 8 ) C - 31 C. 47 CN9560 Sound board I/F connector ( 21 - pin) Table C - 47 Sound board I/F connector ( 21 - pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 VREF1 - P2V O 2 MICIN - PXP O 3 LOUTL - PXP O 4 A - GND - 5 LOUTR - PXP[...]

C.47 CN9560 Sound board I/F connector (21 - pin) Appendix C Pin Assignment C - 32 QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) D - 1 Appendix D Keyboard Scan/Character Codes Appendix D Keyboard Scan/Character Codes Table D - 1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 05 4 $ 05 85 25 [...]

Appendix D Keyboard Scan/Character Codes D - 2 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table D - 1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A2 34 [...]

Appendix D Keyboard Scan/Character Codes QOSMIO F 10 Maintenance Manual (960 - 49 8) D - 3 Table D - 1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F 0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E0 52 E0 D2 E0 70 E0 F0[...]

Appendix D Keyboard Scan/Character Codes D - 4 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table D - 1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code se t 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0[...]

Appendix D Keyboard Scan/Character Codes QOSMIO F 10 Maintenance Manual (960 - 49 8) D - 5 Table D - 2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0[...]

Appendix D Keyboard Scan/Character Codes D - 6 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table D - 3 Scan codes in Numlock mode Code set 1 Code set 2 Cap N o. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ? ? E0 2A E0 4B E0 CB E0 AA E0 12[...]

Appendix D Keyboard Scan/Character Codes QOSMIO F 10 Maintenance Manual (960 - 49 8) D - 7 Table D - 5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C 8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P ( – ) 4A [...]

Appendix D Keyboard Scan/Character Codes D - 8 QOSMIO F 10 Maintenance Manual (960 - 49 8 ) Table D - 7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Common* E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) E - 1 Appendix E Key Layout Appendix E Key Layout E.1 Keyboard Layout Figure E - 1 Keyboard layout (for US) Figure E - 2 Keyboard layout (for UK)[...]

E.1 Keyboard Layout Appendix E Key Layout E - 2 QOSMIO F 10 M aintenance Manual (960 - 49 8 )[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) F - 1 Appendix F Appendix F Wiring Diagrams F.1 LAN Loopback Connector (1) BIBAP ‘ (TX+) (2) BIDAN (TX-) (3) BIDBP (RX+) (4) BIDBN (RX-) Figure F - 1 LAN loopback connector[...]

F.1 LAN Loopback Connector Appendix F Wiring Diagrams F - 2 QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

QOSMIO F 10 Maintenance Manual (960 - 498) G - 1 Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: ? BIOS/EC/KBC rewriting disk Rewriting the BIOS NOTE: 1. Connect the A C adapter to the computer when yo[...]

Appendix G BIOS Rewrite Procedures G - 2 QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

QOSM IO F 10 Maintenance Manual (960 - 498) H - 1 Appendix H Appendix H EC/KBC Rewrite Procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC , you need the following tool: ? EC/KBC rewriting dis k for the computer Rewriting the EC/KBC NOTE: 1. Rewrite the EC/KBS onl[...]

Appendix H EC/KBC Rewrite Procedures H - 2 QOSMIO F 10 Maintenance Manual (960 - 49 8 )[...]

QOSMIO F 10 Maintenance Manual (960 - 49 8 ) I- 1 Appendix I Reliability Appendix I Reliability The following table shows MTBF (Mean Time B etween Failures) in maximum configuration . Table I- 1 MTBF Component Time (hours) System 5,277[...]

Appendix I Reliability I- 2 QOSMIO F10 Maintenance Manual (960 - 49 8 )[...]