Toshiba S4 manuel d'utilisation

[CONFIDENTIAL] Toshiba Personal Computer TECRA S3 TECRA S4 Maintenance Manual TOSHIBA CORPORATION File Number 960-532[...]

ii [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Copyright © 2005 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein. Toshiba Personal C[...]

TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer TECRA S3. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFET[...]

iv [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the TECRA S3 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic opera[...]

TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] v Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM)[...]

vi [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table of Contents Chapter 1 Hardware Overview 1.1 Features .................................................................................................................... .. 1-1 1.2 2.5-inch Hard Disk Drive ..................................................................................[...]

TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] vii Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ................................................................................... 3-4 3.3 Check o[...]

viii [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Chapter 4 Replacement Procedures 4.1 General ..................................................................................................................... .. 4-1 4.2 Battery pack .........................................................................................................[...]

TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] ix Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ................................................................................................ B-1 Appendix C Pin Assignments.................[...]

x [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

[CONFIDENTIAL] Chapter 1 Hardware Overview[...]

1 Hardware Overview 1-ii [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [ CONFIDENTIAL] 1-iii Chapter 1 Contents 1.1 Features.................................................................................................................... ...1-1 1.2 2.5-inch Hard Disk Drive ......................................................................................[...]

1 Hardware Overview 1-iv [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Figures Figure 1-1 Front of the computer .....................................................................................1-5 Figure 1-2 System unit configuration...............................................................................1-6 Figure 1-3 System unit [...]

1.1 Features 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-1 1 Features 1.1 Features The Toshiba TECRA S3 Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Sem iconductor (CMOS) technology extensively to provide compact size, minim um weight, low power usage and high reliabili[...]

1 Hardware Overview 1.1 Features 1-2 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532)  Display LCD The PC comes in with one of the following two types: • 15.0” XGA-TFT color display, resolution 1,024 × 768, 16M colors • 15.0” SXGA+-TFT color display, resolution 1,400 × 1,050, 16M colors External monitor Supported via a RGB connect[...]

1.1 Features 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-3  Toshiba Assist button When this button is pressed during power-on, the PC is connected to “Toshiba Assist”. When this button is pressed during power-off, the PC is turned on and connected to “Toshiba Assist”.  Toshiba Presentation button This bu[...]

1 Hardware Overview 1.1 Features 1-4 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532)  Fingerprint sensor The computer is equipped with a fingerprint sensor and fingerprint authentication utility. They enable only person who has registered his/her fingerprint to use the computer.[...]

1.1 Features 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-5 The front of the computer is shown in figure 1-1. Figure 1-1 Front of the computer[...]

1 Hardware Overview 1.1 Features 1-6 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) The system unit configuration is shown in figure 1-2. Figure 1-2 System unit configuration[...]

1.1 Features 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-7 Figure 1-3 is a block diagram of the system unit. Figure 1-3 System unit block diagram[...]

1 Hardware Overview 1.1 Features 1-8 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) The system unit is composed of the following m ajor components:  Processor • Intel Mobile Pentium-M Processor – Processor core speed: 1.73GHz/1.86GHz/2.0AGHz/2.13GHz/2.26GHz – Processor bus speed: 533MHz – Integrated L1 cache memory: 32KB instructi[...]

1.1 Features 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-9 • South Bridge (Intel ICH6) – DMI (Direct Media Interface) – PCI Express 2 Interface (4ports) – PCI Bus Rev2.3 Interface (7 PCI REQ/GNT Pairs) – Integrated Serial ATA Host Controller (2ports, 150MB/S) – Integrated IDE Controller (Ultra ATA 100/66/3[...]

1 Hardware Overview 1.1 Features 1-10 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532)  Internal LAN Controller (Marvell maid) Controls LAN and supports Gigabit Ethernet. Gigabit is connected to PCI-Express.  Sound Controller Azallia and CODEC (STAC9200) are used.[...]

1.2 2.5-inch Hard Disk Drive 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-11 1.2 2.5-inch Hard Disk Drive The HDD is a random access non-volatile storage device. The computer supports a 40GB, 60GB, 80GB and 100GB HDD. The HDD is shown in figure 1-4. Specifications are listed in Table 1-1. Figure 1-4 2.5-inch HDD Table [...]

1 Hardware Overview 1.2 2.5-inch Hard Disk Drive 1-12 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) Table 1-1 2.5-inch HDD specifications (2/2) Items Specifications TOSHIBA HDD2D34BZK01 TOSHIBA HDD2D33BZK01 TOSHIBA HDD2D32BZK01 TOSHIBA HDD2D30BZK01 Outline Width (mm) 69.85 dimensions Height (mm) 9.5 Depth (mm) 100 Weight (g) 98 max. 102 max[...]

1.3 Keyboard 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-13 1.3 Keyboard The keyboard is mounted 85(US)/86(UK) keys that consist of character key and control key. The keyboard is connected to membrane connector on the system board and controlled by the keyboard controller. Figure 1-5 is a view of the keyboard. See App[...]

1 Hardware Overview 1.4 Optical Drive 1-14 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) 1.4 Optical Drive 1.4.1 DVD-ROM & CD-R/RW Drive The DVD-ROM & CD-R/RW drive accomm odates either 12 cm (4.72-inch) or 8 cm (3.15- inch) CDs, CD-R/RW and DVDs. It is a hi gh-performance drive that writes CD-R at maximum 24-speed and CD-RW at maxi[...]

1.4 Optical Drive 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-15 1.4.2 DVD Super Multi (DVD±R/±RW/-RAM) Drive The DVD Super Multi drive is capable of driving either 12cm (4.72-inch) or 8cm (3.15-inch) DVD and CD without using an adaptor. This drive reads DVD-ROM at maximum 8-speed, reads CD-ROM at maximum 24-speed, [...]

1 Hardware Overview 1.5 TFT Color Display 1-16 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) 1.5 TFT Color Display The TFT color display consists of 15.0-inch XGA/SXGA+ LCD module and FL inverter board. 1.5.1 LCD Module The LCD module used for the TFT color display uses a backlight as the light source and can display a maximum of 16M colors[...]

1.5 TFT Color Display 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-17 Table 1-4 LCD module specifications (2/2) Specifications (15.0-inch SXGA+ TFT) Item LG Philips G33C0001X210 Number of Dots 1,400(W) x 1,050 (H) Dot spacing (mm) 0.2175 (H) x 0.2175 (V) Display range (mm) 304.5 (W) x 228.38 (H) 1.5.2 FL Inverter Board[...]

1 Hardware Overview 1.6 Power Supply 1-18 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) 1.6 Power Supply The power supply supplies many different voltages to the system board and perform s the following functions: 1. Judges that the DC power supply (AC adapter) is connected to the computer. 2. Detects DC output and circuit malfunctions. 3. [...]

1.6 Power Supply 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-19 Table 1-6 Power supply output rating Name Voltage (V) Use PPV 1.404-0.748 CPU PTV 1.05 CPU, MCH, ICH6-M PGV 1.056 GPU 1R5-P1V 1.5 CPU, MCH, ICH6-M, Express Card 1R8-B1V 1.8 MCH, DDR2-SDRAM VG1R8-P1V 1.8 GPU 2R5-P2V 2.5 MCH, ICH6-M MR0R9-B0V 0.9 MCH, DDR2-[...]

1 Hardware Overview 1.7 Batteries 1-20 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) 1.7 Batteries The computer has two types of batteries as follows:  Main battery pack  RTC battery The battery specifications are listed in Table 1-7. Table 1-7 Battery specifications Battery name Material Output voltage Capacity G71C0003W510 G71C0003W[...]

1.7 Batteries 1 Hardware Overview TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 1-21 RTC battery The RTC battery provides power to keep the current date, time and other setup information in memory while the com puter is turned off. Table 1-9 lists the charging time and data preservation period of the RTC battery. Table 1-9 RTC battery chargi[...]

1 Hardware Overview 1.8 AC Adapter 1-22 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) 1.8 AC Adapter The AC adapter is used to charge the battery. Table 1-10 lists the AC adapter specifications. Table 1-10 AC adapter specifications Specification Parameter G71C00043310 (tw o-pins) G71C00049410 (three-pins) Voltage 75W (Peak 90W) Input voltag[...]

[CONFIDENTIAL] Chapter 2 Troubleshooting Procedures[...]

2 Troubleshooting Procedures 2-ii [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 2-iii Chapter 2 Contents 2.1 Troubleshooting ..........................................................................................................2-1 2.2 Troubleshooting Flowchart ...................................................................................[...]

2 Troubleshooting Procedures 2-iv [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 2.8 Display Troubleshooting ..........................................................................................2-48 Procedure 1 Diagnostic Test Program Execution Check ...............................2-48 Procedure 2 Connector Check and Cable Check ........[...]

2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 2-v 2.17 Fingerprint sensor .....................................................................................................2-64 Procedure 1 Setting Windows Log-ON password .........................................2-65 Procedure 2 Registrati on of fingerprint....[...]

2 Troubleshooting Procedures 2-vi [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

2.1 Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-1 2 2.1 Troubleshooting Chapter 2 describes how to determine if a Fi eld Rep laceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Power Supply 6. Display 11. SD Card Slot 2. System Board 7. Optical[...]

2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart 2-2 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determining which FRU malfunctions. Before going through the flowchart steps, check the following:  Ask the user if a password is registered and if it is[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-3 Figure 2-1 Troubleshooting flowchart (1/2)[...]

2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart 2-4 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Figure 2-1 Troubleshooting flowchart (2/2)[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-5 If the diagnostics program cannot detect an er ror, the prob lem may be intermittent. The Running Test program should be executed several times to isolate the problem . Check the Log Utilities function to confirm which diagnostic tes[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-6 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.3 Power Supply Troubleshooting The power supply controls many functions and components. To determ ine if the power supply is functioning properly, start with Proced ure 1 and continue with the other Procedures as instructed. The[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-7 Table 2-2 DC IN icon DC IN icon Po wer supply status Lights green DC power is being supplied from the AC adapter. Blinks orange There is a problem with the powe r supply.*1 Doesn’t light Any condition other than those above. *1 [...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-8 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 2 Error Code Check If the power supply microprocessor detects a ma lfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below.  Start Off for 2 seconds  Error code (8 bit) “1” [...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-9  DC IN Error code Meaning 10h AC Adaptor output voltage is over 16.5V. 11h Common Dock voltage is over 16.5V. 12h Current from the DC power supply is over 7.00A. 13h Current from the DC power supply is over 0.5A when there is n[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-10 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532)  E5V output Error code Meaning 50h E5V voltage is over 6.00V when the computer is powered o n/off. 51h E5V voltage is under 4.50V when the computer i s powered on. 52h E5V voltage is under 4.50V when the computer i s booting u[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-11  PPV output Error code Meaning 90h PPV voltage is over 1.80V when t he computer is powered on/off. 91h PPV voltage is under 0.56V when the computer is powered on. 92h PPV voltage is under 0.56V when t he computer is booting up[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-12 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532)  VG1R8-P1V output Error code Meaning D0h VG1R8-P1V voltage is over 2.16V when the compute r is powered on/off. D1h VG1R8-P1V voltage is under 0.89V wh en the computer is powered on. D2h VG1R8-P1V voltage is under 0.89V wh en t[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-13 Procedure 3 Connection Check The power supply wiring diagram is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from the wall outlet. Check the power cable for breaks.[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-14 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 5 Replacement Check The system board processor module m ay be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Proc edures . Check the connection between the AC a[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-15 2.4 System Board Troubleshooting This section describes how to determine if the system board and CPU are defective or not functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. The proc[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-16 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 1 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes it.  If an error message is sho[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-17 Check 3 The IRT checks the system board. Wh en the IRT detects an error, th e system stops or an error message appears. If one of the following error messages (1) through (17), (22) or (23) is displayed, go to Procedure 4. If err[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-18 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 2 Printer Port LED Check on Boot Mode The printer port LED displays the IRT status a nd test status by turni ng lights on and off as an eight-digit binary value for boot mode . Figure 2-2 shows the printer port LED. Fig[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-19 To use the printer port LED, follow the steps b elow: 1. Turn on the computer’s power and set it to boot mode. 2. Turn off the computer’s power. 3. Plug the printer port LED into the para llel port. 4. While holding down the [...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-20 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-4 Printer port LED boot mode status (1/9) LED Status Test item Contents Permission of A20 and clear of software reset bit Prohibition of APIC Initialization of MCH, ICH Initialization of Super I/O Initialization of debug [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-21 Table 2-4 Printer port LED boot mode status (2/9) LED Status Test item Contents B9h Saving of ke y scan code Setting of TASK_1ms_TSC FAN control Sound initialization (for BEEP sound) Cancel of sound mute Setting of volume to max [...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-22 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-4 Printer port LED boot mode status (3/9) LED Status T est item Message Prohibition of cache Permission of L1/L2 cache in FlashROM area Initialization of H/W (before DRAM recognition) Initialization of MCH Initialization [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-23 Table 2-4 Printer port LED boot mode status (4/9) LED Status Test item Contents Expansion memory checksum check resume error (Resume error LED=76H) PnP RAM checksum check (Resume error LED=77H) Transition to RESUME-MAIN Resume er[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-24 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-4 Printer port LED boot mode status (5/9) LED Status Test item Contents (06h) Battery discharging current control (1CmA). Dividing procedures for time measuring by IRT Setting for clock generator Check of CMOS default set[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-25 Table 2-4 Printer port LED boot mode status (6/9) LED Status Test item Contents 08h PCI bus initialization (connection of DS Bus) Initialization of LAN information WakeUp factor check 09h Task generation for waiting INIT_PCI comp[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-26 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-4 Printer port LED boot mode status (7/9) LED Status Test item Contents 0Fh INIT_SYSTEM (Initialization of system) Storing of CMOS error information to IRT_ERR_STS_BUF Controlling CD POWER SW (model supporting CD play) Ti[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-27 Table 2-4 Printer port LED boot mode status (8/9) LED Status Test item Contents (1Eh) (In the case of “Boot”) Check of key input during IRT (waiting for KBC initialization completion) Input of password (waiting for HDD initia[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-28 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-4 Printer port LED boot mode status (9/9) LED Status Test item Contents (20h) HW initialization before Boot, Waiting for initialization completion Notifies the DVI connection status to VGA BIOS (For models supporting DVI)[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-29 Check 1 I f error code 1Eh or 20h is di splayed, go to the following Sections: Section 2.6 “2.5” HDD Troubleshooting” Check 2 I f the final status of the LED are the followings, perform Procedure 4. Printer port LED error s[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-30 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-5 Printer port LED suspend mode error status (1/3) LED Status Test item Contents Sets the parallel port to D0 state. (For models supporting PRT port) 36h When powering-off request from OS is required, waiting for the comp[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-31 Table 2-5 Printer port LED suspend mode error status (2/3) LED Status Test item Contents 39h Resume error check in suspend mode. Check if IRT process is being executed Check if external option ROM exists Check if FDD motor is rot[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-32 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-5 Printer port LED suspend mode error status (3/3) LED Status Test item Contents 40h Prohibition of PCI arbiter Setting of Wakeup event Power-off of PC card Re-setting backup current Forced off of fan Checks whether off-p[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-33 Table 2-6 Printer port LED resume mode error status (1/4) LED Status Test item Contents 00h Refer to IRT printer LED error status. 01h Refer to IRT printer LED error status. 02h Refer to IRT printer LED error status. 03h Refer to[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-34 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-6 Printer port LED resume mode error status (2/4) LED Status Test item Contents (28h) Initializing of sound Initializing of PCI Express Acquires the multi-box status (For models supporting Select bay) Initializing of HC a[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-35 Table 2-6 Printer port LED resume mode error status (3/4) LED status Test item Con tents (2Bh) Initializing printer mode (For mod els supporting Printer port) Initializing VGA BIOS, when resume Waiting for VGA power on 2Ch Callin[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-36 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Table 2-6 Printer port LED resume mode error status (4/4) LED status Test item Contents (30h) Waiting for the completion of recovery of VGA register Recovery of PIT register Recovery of PCI configuration register Recovery of PIC [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-37 Procedure 4 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. Refer to Chapter 3, Tests and Diagnostics, for more information on how to perform these tests. 1. System test 2. Memor[...]

2 Troubleshooting Procedures 2.5 USB FDD Troubleshooting 2-38 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.5 USB FDD Troubleshooting This section describes how to determine if the USB FDD is functioning properly. Perform the steps below starting with Procedure 1 a nd continuing with the other procedures as required. Procedure 1: USB FDD [...]

2.5 USB FDD Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-39 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedur[...]

2 Troubleshooting Procedures 2.5 USB FDD Troubleshooting 2-40 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 3 Connector Check and Replacement Check The USB FDD is connected to the US board or SR board via the USB port. Check 1 Make sure the USB FDD cable is firmly connected to the connector CN4620/CN4621 on the US board or CN4630 [...]

2.6 HDD Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-41 2 2.6 HDD Troubleshooting This section describes how to determine if the HDD is functioning properly. Perform the steps below starting with Procedure 1 and con tinuing with the other pr ocedures as required. Procedure 1: Partition Check P[...]

2 Troubleshooting Procedures 2.6 HDD Troubleshooting 2-42 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 2 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. When the test detec ts an error, an error m essage is displayed on the screen. Make sure of no floppy[...]

2.6 HDD Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-43 Procedure 3 Format Check The computer’s 2.5” HDD is formatted usi ng the MS-DOS FORMAT program or the physical format program of the test program . To format the 2.5” HDD, start with Check 1 below and perform the other steps as requ[...]

2 Troubleshooting Procedures 2.6 HDD Troubleshooting 2-44 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about t[...]

2.6 HDD Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-45 Procedure 5 Connector Check and Replacement Check The HDD may be disconnected, or the HDD or the system board may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the foll[...]

2 Troubleshooting Procedures 2.7 Keyboard/Touch pad Troubleshooting 2-46 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.7 Keyboard/Touch pad Troubleshooting To determine if the computer’s keyboard or touch pad is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instr[...]

2.7 Keyboard/Touch pad Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-47 Check 3 Make sure the touch pad cable is securely connected to the touch pad and connector CN3201 on the system board. If the connection is loose, r econnect firmly and repeat Pr ocedure 1. If there is still an error, go to[...]

2 Troubleshooting Procedures 2.8 Display Troubleshooting 2-48 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.8 Display Troubleshooting This section describes how to determine if th e com puter’s display is functioning properly. Start with Procedure 1 and continue with the other procedur es as instructed. Procedure 1: Diagnostic Test Prog[...]

2.8 Display Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-49 Procedure 3 Replacement Check Units related to display are a FL inverter board, Display module, System board, LCD/FL cable and display ON/OFF sensor. Any of the components may be damaged. Disassem ble the computer following the steps [...]

2 Troubleshooting Procedures 2.9 Optical drive Troubleshooting 2-50 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.9 Optical drive Troubleshooting This section describes how to determine if the optical driv e in the Slim Select Bay is functioning properly. Perform the steps below starting with Procedure 1 and continue with the other proced[...]

2.10 Modem Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-51 2.10 Modem Troubleshooting This section describes how to determine if the computer’s m odem is functioning properly. Perform the steps below starting with Procedur e 1 and continuing with the other procedures as required. Procedure 1[...]

2 Troubleshooting Procedures 2.10 Modem Troubleshooting 2-52 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 2 Connector Check and Replacement Check The Modem is installed as a Modem Daughter Card (MDC). If the m odem malfunctions, there may be a bad connection between the MDC and the system board or their connectors might be damage[...]

2.11 LAN Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-53 2.11 LAN Troubleshooting This section describes how to determine if the com puter’s LAN is functioning properly. Perform the steps below starting with Procedure 1 and continue with the other procedures as required. Procedure 1: Diagnos[...]

2 Troubleshooting Procedures 2.12 Sound Troubleshooting 2-54 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.12 Sound Troubleshooting This section describes how to determine if the computer’s sound functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Pr[...]

2.12 Sound Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-55 Procedure 2 Connector Check The sound function-wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the com puter following the steps described in Chapter 4, Replacement Procedures and perform the foll[...]

2 Troubleshooting Procedures 2.12 Sound Troubleshooting 2-56 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 3 Replacement Check Check 1 If the stereo speaker or internal microphone does not sound properly, the stereo speaker or internal microphone m ay be defective or damaged. Replace it with a new one. If the stereo speaker or int[...]

2.13 SD Card Slot Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-57 2.13 SD Card Slot Troubleshooting This section describes how to determine if the com puter’s SD card functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedure[...]

2 Troubleshooting Procedures 2.14 Wireless LAN Troubleshooting 2-58 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.14 Wireless LAN Troubleshooting This section describes how to determine if the com puter’s Wireless LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as r[...]

2.14 Wireless LAN Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-59 Procedure 2 Antenna Connection Check The wireless LAN wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the com puter following the steps described in Chapter 4, Replacement Procedures , and [...]

2 Troubleshooting Procedures 2.15 Bluetooth Troubleshooting 2-60 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.15 Bluetooth Troubleshooting To check if the Bluetooth is malfunctioning or not, fo llow the tr oubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving Che ck Procedure 2: Antenna Connection Check Proced[...]

2.15 Bluetooth Troubleshooting 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-61 Procedure 2 Antenna Connection Check The Bluetooth function-wiring diagram is shown below: Any of the connections may be defective. Disassem ble the computer following the steps described in Chapter 4, Replacement Procedures , and [...]

2 Troubleshooting Procedures 2.15 Bluetooth Troubleshooting 2-62 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) Procedure 3 Replacement Check Bluetooth module, Bluetooth an tenna or system board m ay be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disa ssemble the computer and then perform the following chec[...]

2.16 PCI ExpressCard slot 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-63 2.16 PCI ExpressCard slot This section describes how to check PCI Expr essCard slot by inspecting a card with PCI Express interface and a ca rd with USB 2.0 interface. 1. Gigabit Ether ExpressCard 2. USB2.0 5in1 ExpressCard 1. Gigabit E[...]

2 Troubleshooting Procedures 2.17 Fingerprint sensor 2-64 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 2.17 Fingerprint sensor CAUTION : To delete the account for con firming the fingerprint operation, it is necessary to log on by the account wi th the management authority. If the password has been set to log on, ask the Log-ON password to[...]

2.17 Fingerprint sensor 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-65 Procedure 1 Setting Windows Log-ON password 1. Open [User Account] from [Control Panel]. 2. Select “Create a new acc ount” in [User Account]. 3. Input the name of Account (e.g. “TOSHI BA”) in [Nam e the new account] and click [NEX[...]

2 Troubleshooting Procedures 2.17 Fingerprint sensor 2-66 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 3. Input the name of Account (e.g. “TOSHIBA ”), which has been inputted in item 3 in Procedure 1, in the box at th e right of [User Name:] on the [Verify Username and Password]. In addition, input the password, which has been inputted[...]

2.17 Fingerprint sensor 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-67 5. After displaying [Capture Fingerprint], scan the fingerprint of your right index finger on the finger sensor. When it successes the number at the center of display of display changes to “2”, then scan again. W hen it successes th e[...]

2 Troubleshooting Procedures 2.17 Fingerprint sensor 2-68 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 8. When [Audio and Taskbar Settings] is displayed, click [Next]. 9. When [Congratulations] is displayed, click [Done]. 10. When [OmniPass-Logon New User ?] is displayed, click [Yes].[...]

2.17 Fingerprint sensor 2 Troubleshooting Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 2-69 11. Close all applications and power off the computer. Procedure 3 Authenti cation of fingerprint 1. Turn on the computer and start up the Windows. 2. In the Windows Log-ON window, scan the finge rprint of your right index finger. Make su[...]

2 Troubleshooting Procedures 2.17 Fingerprint sensor 2-70 [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 4. After starting Windows, Make sure that th e name of Account (e.g. “TOSHIBA”), which has been inputted in item 3 in Pr ocedure 1 at the top of [Start]. 5. Open [User Accounts] from [Control Panel]. Select [Delete an Account] in [Cha[...]

[CONFIDENTIAL] Chapter 3 Tests and Diagnostics[...]

3 Tests and Diagnostics 3-ii [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 3[...]

3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 3-iii Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.1.1 Diagnostics menu ................................................................................. 3-1 3.1.2 H/ W[...]

3 Tests and Diagnostics 3-iv [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532) 3.21 ONLY ONE TEST ................................................................................................... 3-49 3.21.1 Program Description .......................................................................... 3-49 3.21.2 Operations ..................[...]

3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL ] 3-v 3.31 SETUP ................................................................................................................... 3-100 3.31.1 Function Description ........................................................................ 3-100 3.31.2 Accessing the SETUP P[...]

3 Tests and Diagnostics 3-vi [CONFIDENTIAL] TECRA S3 Maintenance Manu al (960-532)[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The Diagnostics Program s are stored on some Diagnostic Disks. There are Service Program Modules [...]

3 Tests and Diagnostics 3.1 The Diagnostic Test 3-2 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)  HARD DISK TEST  REAL TIMER TEST  NDP TEST  EXPANSION TEST  CD-ROM/DVD-ROM TEST Other tests are:  Wireless LAN TEST (Wireless LAN TEST disk)  LAN/Modem/Bluetooth/IEEE1394 TEST (LAN/Modem/Bluetooth/IEEE1394 TEST disk)  Sou[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-3 3.1.2 H/W (Hardware) initial information setting tool The H/W initial inform ation setting tool consists of the following programs.  Initial configuration  DMI information save  DMI information recovery  System configuration display [...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-4 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.2 Executing the Diagnostic Test To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the USB floppy disk drive. 2. Turn on the computer with pressing the F12 . Select the FDD in the display for selec[...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-5 3.2.1 Diagnostics menu (T&D) To execute this program, select 1- Repair Main (T&D) in the startup menu, press Enter . The following menu appears. TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Co[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-6 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTIC TEST MENU : 1 - SYSTEM TEST 2 - MEMORY[...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-7 Select the option you want to execute and press Enter . When you select 1-SYSTEM TEST , the following message will appear: SYSTEM TEST NAME XXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST :[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-8 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Selecting YES of ERROR STOP stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below: ERROR STATUS NAME [[ HALT OPERATION ]] 1: Test end 2: Continue 3: Retry [...]

3.3 Check of the RAID configuration 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-9 3.3 Check of the RAID configuration Following screen is displayed for checking th e RAID configuration and specifying a failed drive. TOSHIBA RAID / RAID Information Display Rev xx.xx.xxxx Copyright(c) 2005 TOSHIBA CORPORATION. All R[...]

3 Tests and Diagnostics 3.3 Check of the RAID configuration 3-10 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Logical Drive Information: Displays logical drive number, RAID level, RAID status, contents and setting. Physical Drive Information: Displays port number, logical drive number belonged, status and disk inform ation. RAID level: Dis[...]

3.3 Check of the RAID configuration 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-11 3.3.2 Check of the screen display Contents of the screen displayed are shown below. 3.3.2.1 RAID-1 When the “RAID-1” is displayed in the shown below, it is judged that the RAID is configured by two drives. TOSHIBA RAID / RAID In[...]

3 Tests and Diagnostics 3.3 Check of the RAID configuration 3-12 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) TOSHIBA RAID / RAID Information Display Rev xx.xx.xxxx Copyright(c) 2005 TOSHIBA CORPORATION. All Rights Reserved. Level Status Capacity LD0 RAID-0 OPTIMAL xxGB Write cache : Enable MBR Protection : Disable S.M.A.R.T : Enable LD1 R[...]

3.3 Check of the RAID configuration 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-13 TOSHIBA RAID / RAID Information Display Rev xx.xx.xxxx Copyright(c) 2005 TOSHIBA CORPORATION. All Rights Reserved. Level Status Capacity LD0 RAID-1 DEGRADE    xxGB Write cache : Enable MBR Protection : Disable S.M.A.R.T : Enable[...]

3 Tests and Diagnostics 3.3 Check of the RAID configuration 3-14 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.3.3.2 RAID : not OPTIMAL ABSENT or OFFLINE is displayed When the “ABSENT” or “OFFLINE” is displayed as shown below, the drive is removed by the RAID console and installed again. When the drive is unlocked, “ABSENT” is[...]

3.3 Check of the RAID configuration 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-15 NO DRIVE for one drive is displayed When “NO DORIVE” is displayed and the HDD is connected to the port, follow the procedures below to check the HDD failure. When the HDD is not connected to the port, removing of the drive cause[...]

3 Tests and Diagnostics 3.3 Check of the RAID configuration 3-16 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) FAIL for one drive is displayed One drive in the “RAID-1”is failed and degraded. This may look like failure by wrong operation. Specify the reason by using Independent Utility. TOSHIBA RAID / RAID Information Display Rev xx.xx.[...]

3.4 Setting of the hardware configuration 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-17 3.4 Setting of the hardware configuration To execute this program, select 2-Repair initial config set in the startup menu, press Enter and follow the directions on the screen. The H/W initial inform ation setting tool consists[...]

3 Tests and Diagnostics 3.4 Setting of the hardware configuration 3-18 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) • Setting of the HWSC • Setting of the UUID • Display of the DMI information (including UUID) After completion of the above settings, H/W configuration & DMI information are appeared in order. Check the contents and[...]

3.4 Setting of the hardware configuration 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-19 Subtest 08 System configuration display This subtest displays the information of the system configuration. When the following message appears, confirm the contents and press Enter . Press [Enter] key For more details on the sy[...]

3 Tests and Diagnostics 3.5 Heatrun Test 3-20 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.5 Heatrun Test To execute this program, select 3-Repair heatrun in the startup menu, press Enter . When selecting the option you want to execute, the message shown below will appear and 01-ROM Checksum of the SYSTEM test will be executed. SYSTEM TE[...]

3.6 Subtest Names 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-21 3.6 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 03 04 05 ROM checksum Fan ON/OFF Geyserville Quick charge DMI r[...]

3 Tests and Diagnostics 3.6 Subtest Names 3-22 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table 3-1 Subtest names (2/2) No. Test Name Subtest No. Subtest Name 8 HARD DISK 01 02 03 04 05 06 07 08 09 Sequential read Address uniqueness Random address/data Cross talk & peak shift Partial Read Write specified address Read specified addres[...]

3.7 System Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-23 3.7 System Test To execute the System Test, select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 ROM checksum This subtest ex[...]

3 Tests and Diagnostics 3.7 System Test 3-24 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Subtest 03 Geyserville If the CPU supports Gerserville (SpeedStep), this Subtest checks that the CPU operating clock speed can be changed. Subtest 04 Quick charge This subtest checks the status for the quick charge. Subtest 05 DMI read This subtest di[...]

3.8 Memory Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-25 3.8 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Conventional memory This sub[...]

3 Tests and Diagnostics 3.9 Keyboard Test 3-26 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.9 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Pressed key code disp[...]

3.10 Display Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-27 3.10 Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 VRAM read/write for VGA[...]

3 Tests and Diagnostics 3.10 Display Test 3-28 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter . [Mode 12] [Mode 13] [Mode 3 ] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600[...]

3.10 Display Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-29 Subtest 06 “H” Pattern Display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHH[...]

3 Tests and Diagnostics 3.11 Floppy Disk Test 3-30 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.11 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD because the contents of the floppy disk will be erased. To execute the Floppy D[...]

3.11 Floppy Disk Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-31 Select the number of the subtest you want to execute and press Enter . The following message will appear during the floppy disk test. FLOPPY DISK IN PROGRESS XXXXXXX xxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TE[...]

3 Tests and Diagnostics 3.12 Printer Test 3-32 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.12 Printer Test To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE : An IBM compatible printer must be connected to the system to execute this test. Also, printer port wra[...]

3.12 Printer Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-33 Subtest 02 Function This subtest is for IBM compatible printers, and tests the following f unctions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print type[...]

3 Tests and Diagnostics 3.13 Async Test 3-34 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.13 Async Test To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 and 02 require the[...]

3.14 Hard Disk Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-35 3.14 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. CAUTION : The contents of the hard disk will be erased when subtest 02, 03, 04, 06, 08 or 09 is executed[...]

3 Tests and Diagnostics 3.14 Hard Disk Test 3-36 [CO NFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press [Enter] . The following message will appear during each subtest. HARD DISK TEST XXXXXXX XXX DIA[...]

3.14 Hard Disk Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-37 Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder and then reads the data while moving from cylinder to cylinder. (Tests the data interference in the neighbor track.) Worst pat[...]

3 Tests and Diagnostics 3.15 Real Timer Test 3-38 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) 3 3.15 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Real time A[...]

3.15 Real Timer Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-39 Subtest 03 Real time carry CAUTION : When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments, m aking sure the date and time are displayed in the following form at: Current date : 12-[...]

3 Tests and Diagnostics 3.16 NDP Test 3-40 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) 3.16 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 NDP This test checks the following functions of NDP:  Control word  Status word  Bus  Addition ?[...]

3.17 Expansion Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-41 3.17 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wraparound [not supported] CAUTION : PCMCIA wraparound test is not supported for thi[...]

3 Tests and Diagnostics 3.17 Expansion Test 3-42 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) Subtest 02 RGB monitor ID NOTE: To execute this subtest, monitor supporting EDID is required. Connect the external monitor supporting EDID to the PC for the test of ID acquisition. This test is executed by VESA command. .[...]

3.18 CD-ROM/DVD-ROM Test 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-43 3.18 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 12 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE : For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK TDY-01 or ABEX T[...]

3 Tests and Diagnostics 3.19 Error Code and Error Status Names 3-44 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) 3.19 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the Diagnostic Test. Table 3-2 Error codes and error status names (1/3) Device name Error code Error status name (Common) FF Data [...]

3.19 Error Code and Error Status Names 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-45 Table 3-2 Error codes and error status names (2/3) Device name Error code Error status name FDD 01 02 03 04 08 09 10 20 40 80 60 06 EE FDD - BAD COMMAND ERROR FDD - ADDRESS MARK NOT FOUND FDD - WRITE PROTECTED FDD - RECORD NOT FO[...]

3 Tests and Diagnostics 3.19 Error Code and Error Status Names 3-46 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) Table 3-2 Error codes and error status names (3/3) Device name Error code Error status name HDD CC E0 0A EE DA 12 HDD - WRITE FAULT HDD - STATUS ERROR HDD - BAD SECTOR HDD - ACCESS TIME ERROR HDD - NO HDD HDD - DMA CRC ERROR NDP[...]

3.20 Hard Disk Test Detail Status 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-47 3.20 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an eight- digit [...]

3 Tests and Diagnostics 3.20 Hard Disk Test Detail Status 3-48 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) Table 3-4 Error register contents Bit Name Description 7 BBK (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error. “1” … Uncorrec[...]

3.21 ONLY ONE TEST 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-49 3.21 ONLY ONE TEST 3.21.1 Program Description This program tests the unique functions of this model. 3.21.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter . The following menu appears in the display. ##############################[...]

3 Tests and Diagnostics 3.21 ONLY ONE TEST 3-50 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) Subtest 01 Pressed Key Display When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key character that was pressed. Holding a key down[...]

3.21 ONLY ONE TEST 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-51 Subtest 02 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Direction and parameter B) Switching function check This test displays the response from the touch pad and touch pad switch. When moving your finger on the to[...]

3 Tests and Diagnostics 3.21 ONLY ONE TEST 3-52 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) Subtest 03 GP Button This subtest checks moving of the front operation panel button. Press the Toshiba Presentation button after the following message appears. Press [Assist] button Press the Toshiba Assist button after the following message appear[...]

3.21 ONLY ONE TEST 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-53 Subtest 05 USB NOTE : When executing this subtest, USB test module and USB cable must be connected. This subtest checks if USB port works properly. The following menu appears in the display. ##########################################################[...]

3 Tests and Diagnostics 3.21 ONLY ONE TEST 3-54 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) Subtest 06 Docker Dock/Undock This subtest is executed with Common Dock 3 installed. Press Enter while pushing the eject button of the Common Dock 3 after the following message appears. Slide Eject-SW, and press [Enter] Key Press Enter without push[...]

3.21 ONLY ONE TEST 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-55 Subtest 07 LED This subtest checks if each LED lights properly. The following message appears in the display in order. Follow the instructions in the display to execute the test. [HDD Access LED test] Press any key and following message appears in t[...]

3 Tests and Diagnostics 3.21 ONLY ONE TEST 3-56 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) Subtest 08 PC-Card Device Lock This subtest checks the device lock function. This test needs a PC card, not a PC wraparound card. Before this test, inset a PC card. Turn on the computer and select 8 from the only one test menu. When it passes the t[...]

3.21 ONLY ONE TEST 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-57 Subtest 0A Acceleration sensor This subtest detects and corrects the each axis (X, Y, Z). NOTE: Make sure that this subtest is executed on the following condition: 1. Flat desk with vertical plane to get the stability of machine. 2. Prevent the mach[...]

3 Tests and Diagnostics 3.21 ONLY ONE TEST 3-58 [CONFIDENTIAL] TECRA S3 Maintenance Manual ( 960-532) When this subtest is selected, the following message appears in the display. The heaven surface establishes in the upper direction Press [Enter] key NOTE : Be sure to execute the test with the display panel opened. Set the machine on the flat desk.[...]

3.22 Head Cleaning 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-59 3.22 Head Cleaning 3.22.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.22.2 Operations 1. Selecting test 4 from the[...]

3 Tests and Diagnostics 3.23 Log Utilities 3-60 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.23 Log Utilities 3.23.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk, or output the data to a printer or the display. T[...]

3.23 Log Utilities 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-61 3.23.2 Operations 1. Select 5 and press Enter in the DIAGNOSTIC MENU, the error information is displayed in the following format: XXXXX ERRORS CNT TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] 001 FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROT[...]

3 Tests and Diagnostics 3.24 Running Test 3-62 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.24 Running Test 3.24.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02, 06) 3. Display test (subtest 01) 4. Real timer test (subtest 02) 5. HDD t[...]

3.25 Floppy Disk Drive Utilities 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-63 3.25 Floppy Disk Drive Utilities 3.25.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is only for testing a floppy disk dri[...]

3 Tests and Diagnostics 3.25 Floppy Disk Drive Utilities 3-64 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.25.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message. [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2. FORMAT program (a) Selecting [...]

3.25 Floppy Disk Drive Utilities 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-65 3. COPY program (a) When COPY is selected, the following message appears. FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a m essage similar to the one below. Inser[...]

3 Tests and Diagnostics 3.25 Floppy Disk Drive Utilities 3-66 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4. DUMP program (a) When DUMP is selected, the following message appears. DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If 2:HDD is selected, the display will go to ste[...]

3.25 Floppy Disk Drive Utilities 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-67 (k) The following message will appear. To finish the dum p, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UTILITIES MENU. Another dump (1:Yes,2:No) ? 5. HDD ID R[...]

3 Tests and Diagnostics 3.26 System Configuration 3-68 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3 3.26 System Configuration 3.26.1 Function Description NOTE : To display the system configuration, the write protect tab should be OFF position. If the tab is ON position, move the tab to OFF position and restart the test. Otherwise the corr[...]

3.26 System Configuration 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-69 3.26.2 Operations Select 8 from the DIAGNOSTIC MENU and press Enter. Then, the following system configuration appears in the display. System Configuration Display : Ver X.XX [Machine Name ???] * - Processor Type = XXXXXX-XXXXXMHz Code = XX L2[...]

3 Tests and Diagnostics 3.27 Wireless LA N Test Program (Intel-made b/g) 3-70 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.27 Wireless LAN Test Program (Intel-made b/g) This section describes how to perform the wireless LAN transm itting-receiving test (Intel- made Calexico 802.11b/g). To execute the wireless LAN test, use the Diagnostics[...]

3.27 Wireless LAN Test Program (Intel-made b/g) 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-71 When a defective is detected in the test, following typical cause is considered. • Bad connection of wireless LAN card • Using a wrong wireless LAN card (Using unspecified card) • Defective wireless LAN card Check [...]

3 Tests and Diagnostics 3.27 Wireless LA N Test Program (Intel-made b/g) 3-72 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Subtest03 Antenna Check & communication test of 11b mode CAUTION: To execute subtest 03-05, use another computer (with Calexico wireless LAN card) that can communicate by the wireless LAN as a responder machine. Acc[...]

3.27 Wireless LAN Test Program (Intel-made b/g) 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-73 Subtest04 Communication test of 11g mode This subtest checks the communication of wireless LAN antenna of Calexico 802.11g mode. After finishing the test, OK message will appear in the display. Press any key to return to[...]

3 Tests and Diagnostics 3.28 Wireless LA N Test Program (Intel-made a/g) 3-74 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.28 Wireless LAN Test Program (Intel-made a/g) This section describes how to perform the wireless LAN transm itting-receiving test (Intel- made Calexico 802.11a/g). To execute the wireless LAN test, use the Diagnostics[...]

3.28 Wireless LAN Test Program (Intel-made a/g) 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-75 If a defective is found during the test, NG message will appear in the display. Press any key and following message will appear in the display. ************************************************************ * * * SKU NG !![...]

3 Tests and Diagnostics 3.28 Wireless LA N Test Program (Intel-made a/g) 3-76 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) When a defective is detected in the test, following typical cause is considered. • Connection of wireless LAN card • Defective wireless LAN card • Disappearance of MAC address data Checking the connection, execute[...]

3.28 Wireless LAN Test Program (Intel-made a/g) 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-77 When a defective is detected in the test, following typical cause is considered. • Connection of wireless LAN card • Connection of wireless LAN antenna cable (Main/Aux) • Condition of wireless LAN communication (In[...]

3 Tests and Diagnostics 3.28 Wireless LA N Test Program (Intel-made a/g) 3-78 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Subtest05 Communication test of 11g mode This subtest checks the communication of wireless LAN antenna of Calexico 802.11g mode. For more details on procedure and contens of this subtest, refer to Subtest04 Communicatio[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Te st Program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-79 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem/Bluetooth/IEEE1394 test with the test program. Insert the test program disk for LAN/Mode m/Bluetooth/IEEE1394 test in FDD[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-80 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Subtest01 (i82562 + ICHx) NOTE : i82562 + ICHx test is not supported for this model. This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. The following message will appear. [LAN transmit &am[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Te st Program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-81 Subtest02 (GbE) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. Select 2 to execute and press Enter . The following message will appear. Testing adapter...hit <ESC> to abort. * E[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-82 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.29.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “FAT-MODE inspection device (product code: QE2000P01 made by Nitto Electric Manufacture Co.Ltd)” for the t[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Te st Program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-83 3.29.3 Bluetooth test To execute this test, input 3 and press Enter . NOTE : Use another computer that can communicate by the Bluetooth as a reference machine to perform this test. Insert a floppy disk containing the tes[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-84 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Subtest01 BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter . The following message will appear: -------------------------------[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Te st Program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-85 If the target machine has any problem, it displays Error m essage. The following message is displayed. ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(BD[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-86 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-6 Error code for Bluetooth test (BD_ADDR) (1/2) Error code Meani[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Te st Program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-87 Table 3-6 Error code for Bluetooth test (BD_ADDR) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collision. 0x24 LMP PDU[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-88 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) When the test begins, the machine displays BD_ADDR of the DUT. The progress bar appears when the preparation is completed. The following message is displayed. --------------------------------------------------------------[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Te st Program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-89 When the comm unication test has been completed without fail, the DUT machine displays BD_ADDR. If the connection with the tester is completed, the progress bar stops. The following message is shown. --------------------[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-90 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) If any problem is detected during the test, the massage FAIL is displayed on the tester machine with the error code as shown below. The error code begins with the least significant digit. Error code Table 3-7 Error code f[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Te st Program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-91 Table 3-7 Error code for Bluetooth test (BD_ADDR of the DUT) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collision. 0[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-92 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table 3-8 Common error code Error code Meaning 0x30 BT Control Status should be “Disable”, but it is “Enable”. 0x31 BT Control Status should be “Enable”, but it is “Disable”. 0x32 Power Status should be ?[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Te st Program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-93 3.29.4 IEEE1394 test To execute this test, input 4 and press Enter . NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine to perform this test. The following menu will appear[...]

3 Tests and Diagnostics 3.30 Sound Test program 3-94 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3 Tests and Diagnostics 3.30 Sound Test program This section describes how to perform the Sound test. To execute the sound test, refer to the following description. Insert the test program disk for Sound test in the floppy disk drive and turn o[...]

3.30 Sound Test program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-95 *********************************** ******** May I Restart ? ******* *********************************** Press any key to continue… After pressing any key, the machine starts rebooting and sound test menu will appear in the display. Subtest01[...]

3 Tests and Diagnostics 3.30 Sound Test program 3-96 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Subtest02 (Sine Wave) This subtest is executed by loading the COM file (ADSIN.COM). The program expands sine wave data table from 16KB to 64KB, and creates the play data. Then it transfers the data between the DMA and the CODEC to play the sine[...]

3.30 Sound Test program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-97 3.30.3 CD Sound (Standard) test To execute the CD Sound (Standard) test, press 3 and Enter . Insert the test media (TOSHIBA TEST CD-ROM or ABEX TEST CD-ROM) or music CD on the market (if the test media can not be prepared). Following menu appea[...]

3 Tests and Diagnostics 3.30 Sound Test program 3-98 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Subtest03 Test Tone A CAUTION: Before starting subtest03, be sure to set the sound at proper volume. This subtest plays sine wave while changing its table from 100Hz to 20Hz. The test returns to the CD Sound (Standard) menu after the test ends.[...]

3.30 Sound Test program 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-99 3.30.3.2 Audio CD Insert an audio CD and the following menu appears in the display. CD/DVD TEST IN PROGRESS XXXXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT : XX[...]

3 Tests and Diagnostics 3.31 SETUP 3-100 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.31 SETUP 3.31.1 Function Description This program displays the current system setup inform ation as listed below: 1. Memory (a) Total 2. System Date/Time (a) Date (MM-DD-YYYY) (b) Time (HH:MM:SS) 3. Battery (a) Battery Save Mode (b) PCI Express Link ASPM[...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-101 10. I/O Ports (a) Serial (b) Parallel 11. Drives I/O (a) Built-in HDD (b) Select Bay 12. PCI Bus 13. Security Controller (a) TPM (b) Clear TPM Owner 14. Peripheral (a) Internal Pointing Device (b) Ext keyboard “Fn” (c) Parallel Port Mode 15. Legacy Emu[...]

3 Tests and Diagnostics 3.31 SETUP 3-102 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3.31.2 Accessing the SETUP Program Select 0-SETUP in the Main Menu and press Enter key. The following display appears.[...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-103[...]

3 Tests and Diagnostics 3.31 SETUP 3-104 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press ↑ and ↓ to m ove between items in a column. Press Fn + ↑ ( PgUp) and Fn + ↓ ( PgDn) to move between the two pages. 2. Press either the Space [...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-105 SETUP Options The SETUP screen is divided into functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s mem ory. (a) Total This field displays the total amount of mem ory inst[...]

3 Tests and Diagnostics 3.31 SETUP 3-106 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) User Setting Use this option to set the battery save parameters on the sub-window, BATTERY SAVE OPTIONS . Processing Speed This feature changes the CPU processing speed. High CPU operates at high speed. (Default in Full Power Mode) Low CPU operates at low [...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-107 Cooling Method If the CPU becomes too hot, the fan turns on or the processing speed is lowered automatically. When the CPU tem perature falls to a normal range, the fan turns off. Maximum performance If the CPU becomes too hot, the fan turns on automatical[...]

3 Tests and Diagnostics 3.31 SETUP 3-108 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 5. HDD Password This option registers, resets or changes the HDD password. (a) HDD Hard disk for setting the password. When the second HDD is mounted, “Second HDD” can be selected. Built-in HDD The password is set to Built-in HDD. (This cannot be chang[...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-109 6. Boot Priority This tab sets the priority for booting the computer and the priority for the built-in HDD or optional secondary HDD. (a) Boot Priority HDD → FDD → CD-ROM → LAN The computer looks for bootable files in the following order: HDD, FDD, C[...]

3 Tests and Diagnostics 3.31 SETUP 3-110 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) (b) HDD Priority This option enables to select the pr iority for the Built-in HDD, optional second HDD or PC card. Built-in HDD → Second HDD → USB The priority is set as Built-in HDD → Second HDD → USB. (Default) Second HDD → Built-in HDD → USB[...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-111 (c) TV Type This option allows you to select the type of TV. NTSC (Japan) TV in Japanese system. NTSC (US) TV in the U.S. system. (Default) PAL TV in Europe and China system. 8. Others Whether or not you need to configure the computer with these options de[...]

3 Tests and Diagnostics 3.31 SETUP 3-112 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) (c) Auto Power On The Auto Power On has two functions. The result of setting in the sub- window (OPTIONS) is indicated as follows. Disabled Indicated when “Alarm time” set to “Disabled and “Wake- up on LAN” set to “Disabled”. Enabled Indicate[...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-113 (e) Language During Bootup This option selects the language during bootup. This message appears only on the model for TCL(Canada). English The message is displayed in English. (Default) French The message is displayed in French. 9. Configuration This optio[...]

3 Tests and Diagnostics 3.31 SETUP 3-114 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 10. I/O ports This option controls settings for serial/parallel port. NOTE: Do not assign the same interrupt request level and I/O address to the serial port and PC card. (a) Serial Use this option to set the COM level for the serial port. Not used Does no[...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-115 13. Security controller (a) TPM Disables the security controller called TPM (Trusted Platform Module). When the cursor is on the Enable ( Disable ) and the Space is pressed, message is displayed and the PC waits Y or N key input by the user. When Y is pres[...]

3 Tests and Diagnostics 3.31 SETUP 3-116 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) When “Enabled” is selected, the following sub-window appears. Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting a Fn key equivalent will enable you to use “Hotkeys”[...]

3.31 SETUP 3 Tests and Diagnostics TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 3-117 (c) USB-FDD Legacy Emulation. This option sets the type of the USB memory as a startup device. HDD Sets the type of the USB memory to be equivalent to the HDD (Default). Disabled Sets the type of the USB memory to be equivalent to the FDD. 16. PCI LAN This[...]

3 Tests and Diagnostics 3.31 SETUP 3-118 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) (c) Execute Creation This option is displayed, only when the setting is changed in the “Create State”. Set the cursor bar to “Execute Creation” and press Space or Back Space . The following message will appear: Warning: If you change RAID array, yo[...]

[CONFIDENTIAL] Chapter 4 Replacement Procedures[...]

4 Replacement Procedures 4-ii [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-iii Chapter 4 Contents 4.1 General ..................................................................................................................... .. 4-1 4.2 Battery pack .............................................................................................[...]

4 Replacement Procedures 4-iv [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.30 Fluorescent Lamp..................................................................................................... 4-75 4.30.1 Replacing the 15.0-inch XGA LG Philips Fluorescent Lamp ........... 4-76 4.30.2 Replacing the 15.0-inch XGA Sharp Fluorescent Lamp..[...]

4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-v Figure 4-25 Removing the USB board ............................................................................ 4-39 Figure 4-26 Removing the internal microphone.............................................................. 4-41 Figure 4-27 Removing the SR board/DC-IN[...]

4 Replacement Procedures 4-vi [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Figure 4-57 to 4-64 Replacing LG.Philips fluores cent lamp (XGA) (1) to (8) ...... 4-77 to 4-84 Figure 4-65 to 4-87 Replacing Sharp fluorescen t lamp (XGA) (1) to (23) .......... 4-85 to 4-105 Figure 4-88 to 4-91 Replacing Samsung fluorescent lamp (XGA) (1) to (4) ..[...]

4.1 General 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-1 4 Replaceme nt Procedure s 4.1 General This section explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is a guide to which FRUs need t[...]

4 Replacement Procedures 4.1 General 4-2 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1) Always use the genuine battery that is authorized by Toshiba or compatible with the unit. Since other battery packs ha[...]

4.1 General 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-3 Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassem bly steps. Begin each procedure by removing the AC adapter and the battery pack as instructed in th[...]

4 Replacement Procedures 4.1 General 4-4 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Disassembly Procedures The co m puter has four basic types of cable connectors: • Pressure Plate connector • Spring connector • Coaxial connector • Normal Pin connector To disconnect a Pressure Plate connector, lift up the tabs on either side of th[...]

4.1 General 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-5 Assembly Procedures After you have disassembled the computer and fixed or repaired the problem that was causing the computer to operate abnormally, you will need to reassem ble the computer. Install all the removed FRUs following the steps described in the[...]

4 Replacement Procedures 4.1 General 4-6 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Screw Tightening Torque When you fasten screws, be sure to follow the torque list below. CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other damage if screws or components come loose. NOTE: Tos[...]

4.1 General 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-7 Marking of Screws on the Computer Body To make maintenance of the com puter easier, markings of the kinds of the screws including the types and lengths of the screws are indicated on the computer body. Color/Material of screws Symbol  Black B  Silver[...]

4 Replacement Procedures 4.2 Battery pack 4-8 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.2 Battery pack Removing the Battery pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: When handling battery packs, be careful not to short circuit the terminals. Also do not drop, hit or apply impact; do not s[...]

4.2 Battery pack 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-9 Installing the Battery pack To install the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. For environmental re[...]

4 Replacement Procedures 4.3 PC card 4-10 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.3 PC card Removing the PC card To remove the PC card, follow the steps below and refer to Figure 4-2. CAUTION: Before you remove a PC card, refer to the card’s documentation and to your operating system documentation for proper procedures and precauti[...]

4.4 SD card 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-11 4.4 SD card Removing the SD card To remove the SD card, follow the steps below and refer to Figure 4-3. CAUTION: Before you remove the SD card, refer to the card’s documentation and to your operating system documentation for proper procedures and precau[...]

4 Replacement Procedures 4.5 Memory module 4-12 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.5 Memory module Removing the Memory module To remove the mem ory module, make sure the computer is in boot m ode and powered off, follow the steps below and refer to Figure 4-4. CAUTION: The power must be turned off when you remove/insert the memo[...]

4.5 Memory module 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-13 Installing the Memory module To install the memory m odule, make sure the computer is in boot mode and powered off, follow the steps below and refer to Figure 4-4. CAUTION: Do not touch the connectors on the memory module or on the computer. Dust an[...]

4 Replacement Procedures 4.6 HDD 4-14 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.6 HDD CAUTION : When handling the HDD, do not press the top surface as shown by the arrow. Hold it by the sides. Removing the HDD To remove the HDD, follow the steps below and refer to Figure 4-5 and 4-6. 1. Loosen the screw (with e-ring) fixing the HDD cov[...]

4.6 HDD 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-15 NOTE: The following steps describe how to disassemble the HDD assembly; however, do not disassemble if the HDD is working properly. 3. Place the HDD assembly on a flat surface, and remove the following screw s . • M3 × 4S FLAT HEAD screw × 4 4. Separate t[...]

4 Replacement Procedures 4.6 HDD 4-16 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the HDD To install the HDD, follow the steps below and refer to Figure 4-5 and 4-6. CAUTION: Do not hold the HDD by its top and bottom flat surfaces. It may damage the HDD. 1. Seat the HDD in the HDD bracket and secure them with the following screw[...]

4.7 Wireless LAN card 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-17 4.7 Wireless LAN card Removing the Wireless LAN card To remove the wireless LAN card, make sure the com puter is in boot mode and powered off, follow the steps below and refer to Figure 4-7. CAUTION: Do not try to remove the wireless LAN card wi[...]

4 Replacement Procedures 4.7 Wireless LAN card 4-18 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the Wireless LAN card To install the wireless LAN card, make sure the computer is in boot m ode and powered off, follow the steps below and refer to Figure 4-7. CAUTION: Be sure to switch the computer off before installing the wireles[...]

4.8 Slim select bay module 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-19 4.8 Slim select bay module Removing the Slim select bay module To remove the slim select bay m odule, follow the steps below and refer to Figure 4-8 and 4- 9.   The explanation and figure shown below are the optical drive removing/install[...]

4 Replacement Procedures 4.8 Slim select bay module 4-20 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3. Remove the following screws , connector cover and connector from the optical drive assembly. • M2 × 6S BIND screw × 2 4. Remove the following screw and connector cover from the optical drive assembly. • M2 × 3S S-FLAT HEAD screw ?[...]

4.8 Slim select bay module 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-21 Installing the Slim select bay module To install the slim select bay module, follow the steps below and refer to Figure 4-8 and 4-9. 1. Install the connector cover holder to the optical drive assembly and secure it with the following screws[...]

4 Replacement Procedures 4.9 Keyboard 4-22 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.9 Keyboard Removing the Keyboard To remove the keyboard, follow the steps below and refer to Figure 4-10 to 4-13. 1. Turn the computer face up. 2. Open the display and make it flat. 3. Insert your finger into the latches of the both sides and lift up t[...]

4.9 Keyboard 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-23 5. Lift the upper side of the keyboard while releasing three latches and turn it face down on the palm rest. Figure 4-11 Turning over the keyboard 6. Remove the following screw . • M2.5 × 4B FLAT HEAD screw × 1 7. Peel off the adhered portion (adhere[...]

4 Replacement Procedures 4.9 Keyboard 4-24 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 8. Disconnect the keyboard cable from the connector CN3200 on the system board and remove the keyboard. Figure 4-13 Removing the keyboard Installing the Keyboard To install the keyboard, follow the steps below and refer to Figure 4-10 to 4-13. 1. Place t[...]

4.10 Touch pad 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-25 4.10 Touch pad Removing the Touch pad To remove the touch pad, follow the steps below and refer to Figure 4-14 and 4-15. 1. Disconnect the touch pad cable from the connector CN3201 on the system board. 2. Remove the touch pad assembly while releasing t[...]

4 Replacement Procedures 4.10 Touch pad 4-26 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3. Peel off the glass tape and disconnect the touch pad cable from the connector on the touch pad. 4. Remove the following screws and touch pad . • M2.5 × 4B FLAT HEAD screw × 2 Figure 4-15 Removing the touch pad Installing the Touch pad To install[...]

4.11 Bluetooth module 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-27 4.11 Bluetooth module Removing the Bluetooth module To remove the Bluetooth module, follow the steps below and refer to Figure 4-16. 1. Disconnect the Bluetooth antenna cable from the connector on the Bluetooth module. 2. Disconnect the Bluetoot[...]

4 Replacement Procedures 4.11 Bluetooth module 4-28 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the Bluetooth module To install the Bluetooth module, follow the steps below and refer to Figure 4-16. 1. Connect the Bluetooth cable to the connector on the Bluetooth module and set the Bluetooth module to the slot in place. 2. Conne[...]

4.12 Switch membrane 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-29 4.12 Switch membrane Removing the Switch membrane To remove the switch mem brane, follow the steps below and refer to Figure 4-17. 1. Remove the following screw and lift up the upper part of the right side of the switch cover to remove. • M2.5 [...]

4 Replacement Procedures 4.12 Switch membrane 4-30 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the Switch membrane To install the switch membrane, follow the steps below and refer to Figure 4-17. 1. Install the switch membrane in place and secure it with the following screw . • M2.5 × 4B FLAT HEAD screw x1 2. Connect the swit[...]

4.13 Display assembly 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-31 4 Replacement Procedu res 4.13 Display assembly Removing the Display assembly To remove the display assembly, follow the steps below and refer to Figure 4-18 to 4-20. 1. Peel off the insulator and disconnect the finger print sensor cable from th[...]

4 Replacement Procedures 4.13 Display assembly 4-32 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 5. Turn the computer face down and remove the following screws . • M2.5 × 16B FLAT HEAD screw × 8 (“16” in the figure below) • M2.5 × 8B FLAT HEAD screw × 7 (“8” in the figure below) • M2.5 × 4B FLAT HEAD screw × 1 (“4” i[...]

4.13 Display assembly 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-33 6. Turn the computer face up and open the display. 7. Lift the display assembly up to remove while releasing the latches. Figure 4-20 Removing the display assembly (3) Display assembly[...]

4 Replacement Procedures 4.13 Display assembly 4-34 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the Display assembly To install the display assembly, follow the steps below and refer to Figure 4-18 to 4-20. 1. Place the display assembly to the base assembly while engaging the latches. 2. Secure the display assembly (front) with [...]

4.14 RTC battery 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-35 4.14 RTC battery Removing the RTC battery To remove the RTC battery, follow the steps below and refer to Figure 4-21. 1. Disconnect the RTC battery cable from the connector CN9990 on the system board. 2. Turn up the battery holder and remove the RTC [...]

4 Replacement Procedures 4.15 Modem Daughter Card (MDC) 4-36 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.15 Modem Daughter Card (MDC) Removing the Modem Daughter Card To remove the modem daughter card, follow the steps below and refer to Figure 4-22 and 4- 23. 1. Remove the following screws securing the m odem daughter card. • M2 × 4B[...]

4.15 Modem Daughter Card (MDC) 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-37 4. Turn up the insulator and remove the modem jack from the slot. 5. Peel off the glass tape and turn up the insulator ( cable holder ). 6. Disconnect the modem cable from the connector CN3011 on the system board. Figure 4-23 Removing t[...]

4 Replacement Procedures 4.15 Modem Daughter Card (MDC) 4-38 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the Modem Daughter Card (MDC) To install the modem daughter card, follow the steps below and refer to Figure 4-22 to 4-24. 1. Turn up the insulator ( cable holder ) and connect the modem cable to the connector CN3011 on the s[...]

4.16 USB board 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-39 4.16 USB board Removing the USB board To remove the USB board, follow the steps below and refer to Figure 4-25. 1. Remove the following screw and lift up the USB board to the left above. • M2.5 × 6S Tapping screw × 1 2. Disconnect the USB cable fro[...]

4 Replacement Procedures 4.16 USB board 4-40 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the USB board To install the USB board, follow the steps below and refer to Figure 4-25. 1. Connect the USB cable to the connector CN4610 on the system board. 2. Connect the USB cable to the connector CN4622 on the USB board. 3. Install the [...]

4.17 Internal microphone 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-41 4.17 Internal microphone Removing the Internal microphone To remove the internal microphone, follow the steps below and refer to Figure 4-26. 1. Remove the following screws and front panel . • M2.5 × 6S Tapping screw × 2 2. Disconnect the[...]

4 Replacement Procedures 4.17 Internal microphone 4-42 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the Internal microphone To install the internal microphone, follow the steps below and refer to Figure 4-26. 1. Install the internal microphone to the slot of the front panel. (Pass the hole of the microphone rubber through the gui[...]

4.18 SR board/DC-IN jack 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-43 4.18 SR board/DC-IN jack Removing the SR board/DC-IN jack To remove the SR board/DC-IN jack, follow the steps below and refer to Figure 4-27. 1. Remove the following screw and take out the SR board from the slot. • M2.5 × 6S Tapping screw [...]

4 Replacement Procedures 4.18 SR board/DC-IN jack 4-44 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the SR board/DC-IN jack To install the SR board/DC-IN jack, follow the steps below and refer to Figure 4-27 and 4- 28. 1. Connect the DC-IN jack cable to the connector CN8800 on the system board (Pass the cable under the guide) and[...]

4.19 Fan 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-45 4.19 Fan Removing the Fan To remove the fan, follow the steps below and refer to Figure 4-29. 1. Peel off the glass tape . 2. Disconnect the fan cable from the connector CN8770 on the system board. 3. Remove the following screws and fan . • M2.5 × 4B FLAT[...]

4 Replacement Procedures 4.19 Fan 4-46 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the Fan To install the Fan, follow the steps below and refer to Figure 4-29. 1. Install the fan and secure it with the following screws . • M2.5 × 4B FLAT HEAD screw × 2 2. Connect the fan cable to the connector CN8770 on the system board. 3. [...]

4.20 CPU 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-47 4.20 CPU Removing the CPU To remove the CPU, follow the steps below and refer to Figure 4-30 and 4-31. 1. Remove the following screws securing the CPU holder, in the reverse order of the number marked on the holder. • M2 × 4B BIND screw × 3 2. Remove the[...]

4 Replacement Procedures 4.20 CPU 4-48 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3. Unlock the CPU by rotating the cam on the CPU socket 90 degrees to the counterclockwise with a flat-blade screwdriver (in the order shown in the figure below). 4. Remove the CPU . Figure 4-31 Removing the CPU Cam[...]

4.20 CPU 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-49 Installing the CPU To install the CPU, follow the steps below and refer to Figure 4-30 to 4-32. 1. Check that the triangle on the cam is in the unlocking position. 2. Install the CPU to the correct position in the CPU socket. 3. Fix the CPU by rotating the c[...]

4 Replacement Procedures 4.21 GFX board 4-50 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.21 GFX board Removing the GFX board To remove the GFX board, follow the steps below and refer to Figure 4-33 and 4-34. 1. Remove the following screws securing the GPU heat sink, in the reverse order of the number marked on the heat sink. • M2 × 4B[...]

4.21 GFX board 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-51 2. Remove the following screws and disconnect the GFX board from the connector CN5900 on the system board. • M2 × 4B S-FLAT HEAD screw × 2 Figure 4-34 Removing the GFX board Installing the GFX board To install the GFX board, follow the steps below [...]

4 Replacement Procedures 4.22 System board 4-52 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.22 System board Removing the System board To remove the system board, follow the steps below and refer to Figure 4-35 to 4-39. 1. Remove the following screw and HDD cable holder . • M2.5 × 6S Tapping screw × 1 2. Take out the HDD cable of the [...]

4.22 System board 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-53 3. Remove the following screw and system board . • M2.5 × 6S Tapping screw × 1 Figure 4-36 Removing the modem jack 4. Peel off the insulator and disconnect the HDD cable from the connector CN1850 on the back of the system board. Figure 4-37 Remo[...]

4 Replacement Procedures 4.22 System board 4-54 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 5. Remove the following screws and PC card slot from the back of the system board. • M2 × 8B S-FLAT HEAD screw × 2 • M2 × 3S S-FLAT HEAD screw × 2 Figure 4-38 Removing the PC card slot 6. Remove the following screws and north bridge IC heat [...]

4.22 System board 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-55 Installing the System board To install the system board, follow the steps below and refer to Figure 4-35 to 4-39. 1. Install the north bridge IC heat sink in place (back of the system board) and secure it with the following screws . • M2 × 4S S-F[...]

4 Replacement Procedures 4.23 FP board 4-56 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.23 FP board Removing the FP board To remove the FP board, follow the steps below and refer to Figure 4-40. 1. Peel off the glass tape (back of the middle assembly). 2. Remove the following screws and FP board . • M2 × 3S S-FLAT HEAD screw × 2 3. D[...]

4.23 FP board 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-57 Installing the FP board To install the FP board, follow the steps below and refer to Figure 4-40. 1. Connect the FP cable to the connector CN950 on the FP board. 2. Install the FP board in place and secure it with the following screws . • M2 × 3S S-F[...]

4 Replacement Procedures 4.24 LCD unit/FL inverter 4-58 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4 Replaceme nt Procedure s 4.24 LCD unit/FL inverter Removing the LCD unit/FL inverter To remove the LCD unit/FL inverter, follow the steps below and refer to Figure 4-41 to 4-47. 1. Peel off two mask rubbers and two mask seals and remove th[...]

4.24 LCD unit/FL inverter 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-59 3. Peel off one insulator from the FL inverter and take out the other one under the LCD unit. 4. Remove the following screw securing the FL inverter. • M2 × 4B S-FLAT HEAD screw × 1 5. Disconnect two cables from the FL inverter and remov[...]

4 Replacement Procedures 4.24 LCD unit/FL inverter 4-60 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 6. Remove the following screws securing the LCD unit. • M2 × 4B S-FLAT HEAD screw × 2 Figure 4-43 Removing the LCD unit (1) M2 × 4B S-FLAT HEAD LCD unit M2 × 4B S-FLAT HEAD[...]

4.24 LCD unit/FL inverter 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-61 7. Carefully lift up the top of the LCD unit to access the LCD cable. NOTE: When lifting up the top of the LCD unit, hold the corners of the LCD unit. The top edge of the LCD unit is sensitive area. 8. Remove the glass tape securing the LCD [...]

4 Replacement Procedures 4.24 LCD unit/FL inverter 4-62 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 10. Rem ove the following screws and detach two LCD brackets from the LCD unit . • M2 × 3S S-FLAT HEAD screw × 8 Figure 4-45 Removing the LCD bracket 11. Peel off the insulator from the back of the middle cover. Figure 4-46 Peeling off t[...]

4.24 LCD unit/FL inverter 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-63 12. Peel off two insulators (front of the middle assembly). 13. Remove the following screw and LCD cable holder A . • M2.5 × 4S Tapping screw × 1 14. Remove the following screw and LCD cable holder B . • M2.5 × 6S Tapping screw × 1 1[...]

4 Replacement Procedures 4.24 LCD unit/FL inverter 4-64 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Installing the LCD unit/FL inverter To install the LCD unit/FL inverter, follow the steps below and refer to Figure 4-41 to 4-47. 1. Pass the LCD cable through the hole of the middle frame and set it in place. 2. Install the LCD cable holder[...]

4.25 Cover latch 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-65 4.25 Cover latch Removing the Cover latch To remove the cover latch, follow the steps below and refer to Figure 4-48. 1. Remove the cover cap . 2. Remove the cover latch to the direction in the figure below. Be careful not lose the spring Figure 4-48[...]

4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna 4-66 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.26 Wireless LAN antenna/Bluetooth antenna Removing the Wireless LAN antenna/Bluetooth antenna To remove the wireless LAN antenna/Bluetooth antenna, follow the steps below and refer to Figure 4-49 and 4-50. 1. Peel off one[...]

4.26 Wireless LAN antenna/Bluetooth antenna 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-67 3. Peel off eight acetate tapes and one insulator . 4. Peel off the wireless LAN antennas and Bluetooth antenna from the top cover and take them out. Figure 4-50 Removing the wireless LAN antenna/Bluetooth antenna Installin[...]

4 Replacement Procedures 4.27 Hinge 4-68 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.27 Hinge Removing the Hinge To remove the hinge, follow the steps below and refer to Figure 4-51 to 4-53. 1. Remove the following screws and separate the display cover and middle frame . • M2 × 4B BIND screw × 4 • M2.5 × 6S Tapping screw × 2 Figu[...]

4.27 Hinge 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-69 2. Remove the following screw and SPG GND VGA fin . • M2 × 3S S-FLAT HEAD screw × 1 3. Remove the following screws and take out the right hinge from the hole of the middle frame by m oving it to the left. • M2.5 × 6S Tapping screw × 2 Figure 4-52 R[...]

4 Replacement Procedures 4.27 Hinge 4-70 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4. Remove the following screw and take out the left hinge from the hole of the middle frame by moving it to the right. • M2.5 × 6S Tapping screw × 1 Figure 4-53 Removing the hinge (left) M2.5 × 6S Tapping Hinge (left)[...]

4.27 Hinge 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-71 Installing the Hinge To install the hinge, follow the steps below and refer to Figure 4-51 to 4-53. 1. Install the left hinge and secure it with the following screw . • M2.5 × 6S Tapping screw × 1 2. Install the right hinge and secure it with the follo[...]

4 Replacement Procedures 4.28 Speaker 4-72 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.28 Speaker Removing the Speaker To remove the speaker, follow the steps below and refer to Figure 4-54. 1. Peel off four insulators . 2. Remove the left and right speakers from the slots. Figure 4-54 Removing the speaker Installing the Speaker To insta[...]

4.29 Battery slider 4 Replacement Procedures TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-73 4.29 Battery slider Removing the Battery slider To remove the battery slider, follow the steps below and refer to Figure 4-55 and 4-56. 1. Release the latches of the battery slider A and remove the slider cap from the bottom of the computer. 2. Ta[...]

4 Replacement Procedures 4.29 Battery slider 4-74 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3. Release the latches of the battery slider B and remove the slider cap from the bottom of the computer. 4. Take out the battery slider B from the base cover. Figure 4-56 Removing the battery slider B Installing the Battery slider To install the [...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-75 4 4.30 Fluorescent Lamp This system uses LCD modules from the following suppliers. The procedure for replacing the fluorescent lamp is different for each LCD module. Refer to the appropriate procedure. Type Part No. Supplier Section G33C00030110 [...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-76 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.30.1 Replacing the 15.0-inch XGA LG Philips Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or other foreign substance int[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-77 Figure 4-57 Replacing LG.Philips fluorescent lamp (XGA) (1)[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-78 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Disassembly of Top Case 1. Disassembly of Top Case. CAUTION : Pressure or stress should not be given on Source TCP and Gate COF. Figure 4-58 Replacing LG.Philips fluorescent lamp (XGA) (2)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-79 Disassembly of Source PCB 1. Disassembly of Source PCB. CAUTION : Pressure or stress should not be given on PCB and TCP. Figure 4-59 Replacing LG.Philips fluorescent lamp (XGA) (3)[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-80 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Disassembly of Board Ass’y, Tape Adhesi ve, Light guide, Cover Ass’y Bottom (L) 1. Disassembly of Board Ass’y. CAUTION : This process should be made in Clean room with no scratch nor particle on Polarizer and B/L Ass’y. 2. Disassembly of [...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-81 Assembly of Cover Ass’y Bottom (L), Sheets, Light guide, Tape Adhesive and Board Ass’y. 1. Assembly of Cover Ass’y Bottom and Screw (2 Point). CAUTION : Maximum value of torque with Screw should be below 2.0kgf.cm. 2. Assembly of Light Guid[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-82 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Assembly of Source PCB 1. Assembly of Source PCB. CAUTION : Stress should not be given on TCP. Figure 4-62 Replacing LG.Philips fluorescent lamp (XGA) (6)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-83 Assembly of Top Case 1. Assembly of Top Case. CAUTION : Pressure should not be given on Source TCP and Gate COF. Figure 4-63 Replacing LG.Philips fluorescent lamp (XGA) (7)[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-84 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Assembly of outside Tape and Cover shield 1. Assembly of Cover shield (S). CAUTION : Pressure or stress should not be given on Source PCB. Usage of gloves with anti-electric discharge coating is recommended. To eliminate possible damage on circui[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-85 4.30.2 Replacing the 15.0-in ch XGA Sharp Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or other foreign substance into th[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-86 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 2. Remove the four screws (E) on the both sides. Figure 4-66 Replacing Sharp fluorescent lamp (XGA) (2) Screw loosening torque: 1.2kg.cm (E) (E) (E) (E)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-87 3. Turn the LCD module face up and remove the bezel (F). Figure 4-67 Replacing Sharp fluorescent lamp (XGA) (3) ( 1) Release two latches of the P-chassis. ( 2) Release two latches of the lump cover. ( 3) Release the hook of the bezel. Be careful [...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-88 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4. Turn the LCD module face down and remove the screw (E) fixing the board. Then open the bent portion of the TCP of the board and remove the backlight. Figure 4-68 Replacing Sharp fluorescent lamp (XGA) (4) Figure 4-69 Replacing Sharp fluorescen[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-89 5. Turn the LCD module face up and remove the LCD panel (G) from the backlight unit (H). CAUTION: Wear finger sacks or gloves during the work not to soil or scratch the LCD panel or backlight unit. Figure 4-70 Replacing Sharp fluorescent lamp (XG[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-90 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 6. Peel off four fixing tapes (P). CAUTION: Keep the removed fixing tapes (P) to reuse. Figure 4-71 Replacing Sharp fluorescent lamp (XGA) (7)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-91 7. Remove the lens sheet (M), diffusion sheet (N) and light guide plate (O). CAUTION: Be careful not to scratch or soil the removed sheets and light guide to reuse them. Figure 4-72 Replacing Sharp fluorescent lamp (XGA) (8) Do not remove the ref[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-92 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 8. Turn the back light unit (G) face down and remove two screws (I), lump cover (J), metal fitting A (K) and m etal fitting B (L). CAUTION: Be careful not to scratch or soil the back light unit. Figure 4-73 Replacing Sharp fluorescent lamp (XGA) [...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-93 9. Remove the lamp unit (Q) from the P-chassis. CAUTION: When removing the lamp unit, be careful not to break the lamp, or bend the reflection sheet. Figure 4-74 Replacing Sharp fluorescent lamp (XGA) (10) ( Q )[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-94 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Assembling the 15.0-inch XGA Sharp fluorescent lamp To assemble the 15.0-inch Sharp XGA fluorescent lamp, follow the steps below and refer to figures 4-75 to 4-87. 1. Install a new lamp unit (Q) on the P-chassis. CAUTION: When install the lamp un[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-95 Figure 4-76 Replacing Sharp fluorescent lamp (XGA) (12) Install the lamp unit without floating. Install the reflection sheet as it is placed inside the reflector. Install the lead wire into this groove. Cross-section drawing of Z-Z[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-96 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 2. Install the metal fitting A (K), m etal fitting B (L) and lump cover (J) on the backlight unit and secure the two screws (I). Figure 4-77 Replacing Sharp fluorescent lamp (XGA) (13) 3. Install the light guide plate (O) on the backlight unit. ([...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-97 4. Place the diffusion sheet (N) and lens sheet (M) on the backlight unit with light guide plate. Figure 4-79 Replacing Sharp fluorescent lamp (XGA) (15) Make sure there is no dust or scr atch. Do not make any sheet over the edge of P-chassis. An[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-98 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 5. Stick four fixing tapes (P). Figure 4-80 Replacing Sharp fluorescent lamp (XGA) (16) Two p laces Two p laces[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-99 6. Place the LCD panel (H) on the backlight unit (G). CAUTION: Make sure there is no dust between the LCD panel and backlight unit. If any dust is found, remove it with crepe tape or others, which has no remaining of paste. Figure 4-81 Replacing [...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-100 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 7. Bend the TCP attaching to the source board and secure the screw (E). Figure 4-82 Replacing Sharp fluorescent lamp (XGA) (18) Do not hold the edge. Do not hold the edge.[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-101 Figure 4-83 Replacing Sharp fluorescent lamp (XGA) (19) Screw tightening torque: 1.2kg.cm ( E )[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-102 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 8. Install the bezel (F) on the lamp cover and hook four latches on the lamp cover and two latches on the P-chassis. Figure 4-84 Replacing Sharp fluorescent lamp (XGA) (20) (1) Hitch the hook of the bezel on the rib of the P-chassis. (2) Lean th[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-103 Figure 4-85 Replacing Sharp fluorescent lamp (XGA) (21) Make sure of mating of the bez el and the rib of the P-chassis. Make sure of mating of the bezel and the latch of the P-chassis. Make sure of mating of the bezel and the latch of the P-chas[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-104 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 9. Secure the four screws (E) on the both sides. Figure 4-86 Replacing Sharp fluorescent lamp (XGA) (22) Screw tightening torque: 1.2kg.cm (E) (E) (E) (E)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-105 10. Stick the protection cover G (B), protection cover SC (A) and two fixing tapes (C) and (D). Figure 4-87 Replacing Sharp fluorescent lamp (XGA) (23) (A) (B) (C) (D) 0 to 1 0 to 1 Fit the cover according to the outline of the screw. 0 to 1 mm [...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-106 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 4.30.3 Replacing the 15.0-inch XGA Samsung Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or other foreign substance into [...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-107 2. Remove the white tapes, lamp-wire tape and alum inum tape. Figure 4-89 Replacing Samsung fluorescent lamp (XGA) (2) White tape A I tape Lump wire tape[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-108 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3. Separate the Top Chassis from the Mold frame. CAUTION: The order : Bottom hook ⇒ Side hook [Left & Right] Figure 4-90 Replacing Samsung fluorescent lamp (XGA) (3)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-109 4. Separate the Panel assembly from the BLU CAUTION : Handle with care not to damage the COF of S/D and G/D ICs. Figure 4-91 Replacing Samsung fluorescent lamp (XGA) (4)[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-110 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Assembling the 15.0-inch XGA Samsung Fluorescent Lamp To assemble the 15.0-inch XGA Samsung fluorescent lam p, follow the steps below and refer to Figure 4-88 to 4-91. Assembling is the opposite order of the disassembling.[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-111 4.30.4 Replacing the 15.0-inch SXGA+ LG Philips Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or other foreign substance [...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-112 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Figure 4-92 Replacing LG Philips fluorescent lamp (SXGA+) (1)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-113 Disassembly of Top Case 1. Disassembly of Top Case. CAUTION : Pressure or stress should not be given on Source COF and Gate COF. Figure 4-93 Replacing LG Philips fluorescent lamp (SXGA+) (2)[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-114 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Disassembly of Source PCB 1. Disassembly of Source PCB. CAUTION : Pressure or stress should not be given on PCB and COF. Figure 4-94 Replacing LG Philips fluorescent lamp (SXGA+) (3)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-115 Disassembly of Board Ass’y, Tape Adhesi ve, Light guide, Cover Ass’y Bottom (L) 1. Disassembly of Board Ass’y. CAUTION : This process should be made in Clean room with no scratch nor particle on Polarizer and B/L Ass’y. 2. Disassembly of[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-116 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Figure 4-95 Replacing LG Philips fluorescent lamp (SXGA+) (4)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-117 Assembling the 15.0-inch SXGA+ LG Philips Fluorescent Lamp To assemble the 15.0-inch SXGA+ LG Philips fluorescent lamp, follow the steps below and refer to Figure 4-96 to 4-99. Assembly of Cover Ass’y Bottom (L), Sheets, Light guide, Tape Adhe[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-118 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Figure 4-96 Replacing LG Philips fluorescent lamp (SXGA+) (5)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-119 Assembly of Source PCB 1. Assembly of Source PCB. CAUTION: Stress should not be given on COF. Figure 4-97 Replacing LG Philips fluorescent lamp (SXGA+) (6)[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-120 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Assembly of Top Case 1. Assembly of Top Case. CAUTION: Pressure should not be given on Source COF and Gate COF. Figure 4-98 Replacing LG Philips fluorescent lamp (SXGA+) (7)[...]

4.30 Fluorescent Lamp 4 Replacement Procedure TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] 4-121 Assembly of outside Tape and Cover shield 1. Assembly of Cover shield (S). CAUTION : Pressure or stress should not be given on Source PCB. Usage of gloves with anti-electric discharge coating is recommended. To eliminate possible damage on circu[...]

4 Replacement Procedure 4.30 Fluorescent Lamp 4-122 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

[CONFIDENTIAL] Appendices[...]

Appendices App-ii [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] App-iii Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout .................................................................................................B-1 B.1 System Board (FDR[...]

Appendices App-iv [CONFID ENTIAL] TECRA S3 Maintenance Manual (960-532) C.22 CN5620 RGB connector (15-pin) .......................................................................C-23 C.23 CN5501 S-VIDEO connector (4-pin) .................................................................C-23 C.24 CN5900 GFX board interface connector (230-pin) .......[...]

Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] App-v F.6 RS232C direct-connection cable (9-pin to 25-pin) ................................................ F-3 Appendix G BIOS rewrite Procedures ............................................................................ G-1 Appendix H EC/KBC rewrite Procedures .....................[...]

Appendices App-vi [CONFID ENTIAL] TECRA S3 Maintenance Manual (960-532) Tables Table B-1 System board (FDRSY*) ICs and connectors (front) .......................................B-2 Table B-2 System board (FDRSY*) ICs and connectors (back) .......................................B-4 Table B-3 US board (FDRUS*) connectors .............................[...]

Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] App-vii Table C-25 Internal microphone connector (2-pin) ........................................................C-28 Table C-26 External microphone connector (5-pin) .......................................................C-28 Table C-27 Speaker connector (4-pin) ......................[...]

Appendices App-viii [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table J-5 Item of parameter set ....................................................................................... J-14 Table J-6 Item of array .................................................................................................... J-20 Table J-7 Items set in[...]

Appendix A Handling the LCD Module Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] A-1 Appendix A P Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LC[...]

Appendices Appendix A Handling the LCD Module A-2 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply [...]

Appendix A Handling the LCD Module Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] A-3 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a [...]

Appendices Appendix A Handling the LCD Module A-4 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer da[...]

Appendix A Handling the LCD Module Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] A-5 9. Do not disassemble the LCD module. Disassem bly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These m aterials can release gas that can[...]

Appendices Appendix A Handling the LCD Module A-6 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

Appendix B Board Layout Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] B-1 Appendix B Board Layout B.1 Sy stem Board (FDRSY*) Front View Figure B-1 System board ( FDRSY* ) layout (front) ( A ) ( B ) ( C ) (D) ( E ) ( F ) ( G ) ( H ) ( I ) ( J ) ( K ) ( L ) ( M ) ( N ) ( O ) ( P ) ( Q ) ( R ) ( S ) ( T ) ( U ) ( V ) ( W ) ( X ) ( Y [...]

Appendices Appendix B Board Layout B-2 [CONFID ENTIAL] TECRA S3 Maintenance Manual (960-532) Table B-1 System board ( FDRSY* ) ICs and connectors (front) Mark Number Name (A) J6310 Headphone connector (B) J6051 External microphone connector (C) CN4200 IEEE1394 connector (D) CN6050 Internal microphone connector (E) CN9990 RTC battery connector (F) C[...]

Appendix B Board Layout Appendices TECRA S3 Maintenance Manual (960-532) [ CONFIDENTIAL] B-3 B.2 Sy stem Board (FDRSY*) Back View Figure B-2 System board ( FDRSY* ) layout (back) (A) (B) (C) (D) (E) (F) (G)[...]

Appendices Appendix B Board Layout B-4 [CONFID ENTIAL] TECRA S3 Maintenance Manual (960-532) Table B-2 System board ( FDRSY* ) ICs and connectors (back) Mark Number Name (A) CN2300 Docking I/F connector (B) CN1850 （） SATA HDD I/F connector (C) CN2200 Wireless LAN card I/F connector (D) IC2000 PC card controller (E) IS2101 SD card connector (F) [...]

Appendix B Board Layout Appendices TECRA S3 Maintenance Manual (960-532) [ CONFIDENTIAL] B-5 B.3 US Board (FDRUS*) Front and Back View (front) (back) Figure B-3 US Board (FDRUS*) layout (front/back) Table B-3 US Board (FDRUS*) connectors Mark Number Name (A) CN4622 System board I/F connector (B) CN4620 USB 3connector (C) CN4621 USB 4 connector (B) [...]

Appendices Appendix B Board Layout B-6 [CONFID ENTIAL] TECRA S3 Maintenance Manual (960-532) B.4 SR Board (FDRSR*) Front and Back View (front) (back) Figure B-4 SR Board (FDRSR*) layout (front/back) Table B-4 SR Board (FDRSR*) connectors Mark Number Name (A) CN9510 System board I/F connector (B) CN3420 Serial port (C) CN4630 USB 6 connector (A) (B)[...]

Appendix B Board Layout Appendices TECRA S3 Maintenance Manual (960-532) [ CONFIDENTIAL] B-7 B.5 FS Board (FDRFS*) Front and Back View (front) (back) Figure B-5 FS Board (FDRFS*) layout (front/back) Table B-5 FS Board (FDRFS*) connectors Mark Number Name (A) CN950 System board I/F connector (A)[...]

Appendices Appendix B Board Layout B-8 [CONFID ENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [ CONFIDENTIAL] C-1 Appendix C Appendix C Pin Assignments System board C.1 CN1410 SO-DIMM0 connector (200-pin) Table C-1 SO-DIMM0 connector (200-pin) (1/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MRVREF-B0V - 2 GND - 3 GND - 4 ADQ04-B1P I/O 5 ADQ01-B1P I/O 6 ADQ05[...]

Appendices Appendix C Pin Assignments C-2 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table C-1 SO-DIMM0 connector (200-pin) (2/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 63 ADQ25-B1P I/O 64 ADQ28-B1P I/O 65 GND - 66 GND - 67 ADM3-B1P I/O 68 ADQS3-B1N I/O 69 NC - 70 ADQS3-B1P I/O 71 GND - 72 GND - 73 ADQ26-B1P I/O 74 ADQ30-B1P I/O [...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-3 Table C-1 SO-DIMM0 connector (200-pin) (3/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 139 GND - 140 ADQ41-B1P I/O 141 ADQ44-B1P I/O 142 ADQ40-B1P I/O 143 ADQ45-B1P I/O 144 GND - 145 GND - 146 ADQS5-B1N I/O 147 ADM5-B1P O 148 ADQS5-B1P I/O 149 GND -[...]

Appendices Appendix C Pin Assignments C-4 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) C.2 CN1400 SO-DIMM1 connector (200-pin) Table C-2 SO-DIMM1 connector (200-pin) (1/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MRBREF-B0V - 2 GND - 3 GND - 4 BDQ01-B1P I/O 5 BDQ05-B1P I/O 6 BDQ00-B1P I/O 7 BDQ04-B1P I/O 8 GND - 9G N D - 10 BDM0-B1[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-5 Table C-2 SO-DIMM1 connector (200-pin) (2/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 63 BDQ30-B1P I/O 64 BDQ25-B1P I/O 65 GND - 66 GND - 67 BDM3-B1P I/O 68 BDQS3-B1N I/O 69 NC - 70 BDQS3-B1P I/O 71 GND - 72 GND - 73 BDQ27-B1P I/O 74 BDQ29-B1P I/O [...]

Appendices Appendix C Pin Assignments C-6 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table C-2 SO-DIMM1 connector (200-pin) (3/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 139 GND - 140 BDQ41-B1P I/O 141 BDQ45-B1P I/O 142 BDQ40-B1P I/O 143 BDQ44-B1P I/O 144 GND - 145 GND - 146 BDQS5-B1N I/O 147 BDM5-B1P O 148 BDQS5-B1P I/O 149 GND -[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-7 C.3 CN1850 SATA interface connector (11-pin) Table C-3 SATA interface connector (11-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 SATAT0-P3P O 2 SATAT0-P3N O 3 GND - 4 SATAR0-P3N I 5 SATAR0-P3P I 6 GND - 7P 3 V - 8G N D - 9P 5 V - 1 0 G N D - 11 [...]

Appendices Appendix C Pin Assignments C-8 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table C-4 Select bay interface connector (72-pin) (2/2) Pin No. Signal Name I/O Pin No. Signal Name I/O 45 PDD00-P3P I/O 46 PDD14-P3P I/O 47 PDD01-P3P I/O 48 PDD13-P3P I/O 49 GND - 50 GND - 51 GND - 52 PDD12-P3P I/O 53 PDD02-P3P I/O 54 PDD11-P3P I/O 55 PD[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-9 C.5 CN2100 PC card interface connector (150-pin) Table C-5 PC card interface connector (150-pin) (1/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 1G N D - 2G N D - 3N C - 4N C - 5N C - 6N C - I 7N C - 8N C - 9G N D - 1 0 N C - 11 NC - 12 NC - 13 NC -[...]

Appendices Appendix C Pin Assignments C-10 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table C-5 PC card ard interface connector (150-pin) (2/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 71 GND - 72 USBP6-S3P I/O 73 USBP6-S3N I/O 74 GND - 75 GND - 76 GND - 77 GND - 78 ACCD2-E3N I 79 ACCLKR-EYN I/O 80 ACAD31-EYP I/O 81 ACD02-EYP I/O 8[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-11 Table C-5 PC card interface connector (150-pin) (3/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 145 ACAD01-EYP I/O 146 ACAD02-EYP I/O 147 ACAD00-EYP I/O 148 ACCD1-E3N I 149 GND - 150 GND - 1T GND - 2T GND - C.6 IS2101 SD card interface connector (1[...]

Appendices Appendix C Pin Assignments C-12 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) C.7 CN2200 Mini PCI interface connector (124-pin) Table C-7 Mini PCI interface connector (124-pin) (1/2) Pin No. Signal Name I/O Pin No. Signal Name I/O 1N C - 2N C - 3N C - 4N C - 5N C - 6N C - 7N C - 8N C - 9N C - 1 0 N C - 11 NC - 12 NC - 13 (WLON-S3N[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-13 Table C-7 Mini PCI interface connector (124-pin) (2/2) Pin No. Signal Name I/O Pin No. Signal Name I/O 69 GND - 70 P3V - 71 PERR-P3N I/O 72 DEVSEL-P3N I/O 73 CBE1-P3N I/O 74 GND - 75 AD14-P3P I/O 76 AD15-P3P I/O 77 GND - 78 AD13-P3P I/O 79 AD12-P3P I/O 8[...]

Appendices Appendix C Pin Assignments C-14 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) C.8 CN2300 Docking interface connector (240-pin) Table C-8 Docking interface connector (240-pin) (1/4) Pin No. Signal Name I/O Pin No. Signal Name I/O A1 DSKDC - A2 GND - 1 DCOUT - 2 DCOUT - 3 DOCDT1-S3N I 4I F - P 5 V - 5 EXMSCK-P5P I/O 6 EXKBCK-P5P I/O[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-15 Table C-8 Docking interface connector (240-pin) (2/4) Pin No. Signal Name I/O Pin No. Signal Name I/O 71 GND - 72 NVASDA-P3P I/O 73 GND - 74 GND - 75 GND - 76 DHSYNC-P3P O 77 NVBSDA-P3P I/O 78 NC - 79 GND - 80 NC - 81 NC - 82 NC - 83 NC - 84 NC - 85 NC -[...]

Appendices Appendix C Pin Assignments C-16 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table C-8 Docking interface connector (240-pin) (3/4) Pin No. Signal Name I/O Pin No. Signal Name I/O 147 PDB06-P5P I/O 148 GND - 149 GND - 150 PDB04-P5P I/O 151 PDB01-P5P I/O 152 PDB02-P5P I/O 153 PDB00-P5P I/O 154 STROB-P5N O 155 NC - 156 NC - 157 GND [...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-17 Table C-8 Docking interface connector (240-pin) (4/4) Pin No. Signal Name I/O Pin No. Signal Name I/O 223 NC - 224 NC - 225 GND - 226 NC - 227 NC - 228 NC - 229 GND 230 NC - 231 NC - 232 NC - 233 GND - 234 ACT-E3N I 235 LINK-E3N I 236 DOCDT2-S3N I 237 No[...]

Appendices Appendix C Pin Assignments C-18 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) C.11 CN3200 Keyboard interface connector (34-pin) Table C-11 Keyboard interface connector (34-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1T GND - 2T GND - 1P 5 V - 2 SPY-PXP O 3 SP-GND - 4 SPX-PXP O 5 SP-P5V - 6P 5 V - 7 KBSC15-S3N O 8 KBSC14-S[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-19 C.13 CN3260 SW board interface connector (13-pin) Table C-13 SW board interface connector (13-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GPBTNB-S3W I 2N C - 3 NC - 4 GPBTNA-S3N I 5 NC - 6 NC - 7 PWRSW-S3N I 8 NC - 9 NC - 10 GND - 11 NC - 12 N[...]

Appendices Appendix C Pin Assignments C-20 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) C.15 CN3401 Parallel port interface connector (25-pin) Table C-15 Parallel port interface connector (25-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 STROB-P5N O 2 PDB00-P5P I/O 3 PDB01-P5P I/O 4 PDB02-P5P I/O 5 PDB03-P5P I/O 6 PDB04-P5P I/O 7 P[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-21 C.18 CN4400 Bluetooth interface connector (20-pin) Table C-18 Bluetooth interface connector (20-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND - 2 NC - 3 BTMDL-P3N I 4 NC - 5N C - 6 N C - 7N C - 8 B T R S T - S 3 N O 9N C - 1 0 N C - 11 GND -[...]

Appendices Appendix C Pin Assignments C-22 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) C.21 CN5500 LCD interface connector (40-pin) Table C-21 LCD interface connector (40-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 BRT2DA-S3P O 2 BRT1-P5P O 3 BRT0-P5P O 4 FL-P5V - 5 FL-P5V - 6 FL-P5V - 7N C - 8 G N D - 9 GND - 10 GND - 11 NC - 1[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-23 C.22 CN5620 RGB connector (15-pin) Table C-22 RGB connector (15-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 SYSRED-PXP O 2 SYSGRN-PXP O 3 SYSBLU-PXP O 4 NC - 5G N D - 6G N D - 7G N D - 8G N D - 9 DDC-P5V - 10 GND - 11 NC - 12 CRTSDA-P5P I/O 13[...]

Appendices Appendix C Pin Assignments C-24 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) C.24 CN5900 GFX board interface connector (230-pin) Table C-24 GFX board interface connector (230-pin) (1/4) PIN No. Signal name I/O PIN No. Signal name I/O 1 PVT-EFV - 2 1R5-P1V - 3 PVT-EFV - 4 1R5-P1V - 5 PVT-EFV - 6 1R5-P1V - 7 PVT-EFV - 8 1R5-P1V - 9[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-25 Table C-24 GFX board interface connector (230-pin) (2/4) PIN No. Signal name I/O PIN No. Signal name I/O 59 GND - 60 GND - 61 PEGC14-P1N I 62 PECG14-P1N O 63 PEGC14-P1P I 64 PECG14-P1P O 65 GND - 66 GND - 67 PEGC13-P1N I 68 PECG13-P1N O 69 PEGC13-P1P I 7[...]

Appendices Appendix C Pin Assignments C-26 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table C-24 GFX board interface connector (230-pin) (3/4) PIN No. Signal name I/O PIN No. Signal name I/O 123 PEGC04-P1P I 124 PECG04-P1P O 125 GND - 126 GND - 127 PEGC03-P1N I 128 PECG03-P1N O 129 PEGC03-P1P 130 PECG03-P1P O 131 GND - 132 GND - 133 PEGC0[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-27 Table C-24 GFX board interface connector (230-pin) (4/4) PIN No. Signal name I/O PIN No. Signal name I/O 181 DVATX2-P3N I 182 TSDA-P3P I/O 183 GND 184 TSCL-P3P I/O 185 DVITXC-P3P - 186 GALERT-P3N I 187 DVACK-P3N - 188 GTHERM-P3N I 189 GND 190 GPUHOT-S5N [...]

Appendices Appendix C Pin Assignments C-28 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) C.25 CN6050 Internal microphone connector (2-pin) Table C-25 Internal microphone connector (2-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MICIN I 2 A-GND - C.26 J6051 External microphone connector (5-pin) Table C-26 External microphone connect[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-29 C.30 CN8020 Main Battery connector (10-pin) Table C-30 Main Battery connector (10-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PVBL1 - 2 BTMP1 I 3 (DCHG) - 4 M5V - 5 PSCL-S5P I/O 6 PSDA-S5P I/O 7 GND - 8 DBT10V-S5N O 9 GND - 10 GND - C.31 CN999[...]

Appendices Appendix C Pin Assignments C-30 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) FDRSR Board C.34 CN9510 System board interface connector (20-pin) Table C-34 System board interface connector (20-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 USB1PS-E5V I 2 U SB1PS-E5V I 3 USB1PS-E5V I/O 4 USBP6-E3P I/O 5G N D - 6E 5 V - 7N C [...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-31 FDRFS Board C.37 CN950 System board interface connector (8-pin) Table C-37 System board interface connector (8-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1N C - 2N C - 3 P3V - 4 FGSPON-S3N I 5 GND - 6 USBFS-E3N I/O 7 USBFS-E3P I/O 8 GND - 1T GN[...]

Appendices Appendix C Pin Assignments C-32 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) FDRVG Board C.38 CN5901 System board interface connector (230-pin) Table C-38 System board interface connector (230-pin)(1/4) PIN No. Signal name I/O PIN No. Signal name I/O 1 PVT-EFV - 2 1R5-P1V - 3 PVT-EFV - 4 1R5-P1V - 5 PVT-EFV - 6 1R5-P1V - 7 PVT-EF[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-33 Table C-38 System board interface connector (230-pin)(2/4) PIN No. Signal name I/O PIN No. Signal name I/O 59 GND - 60 GND 61 PEGC14-P1N O 62 PECG14-P1N I 63 PEGC14-P1P O 64 PECG14-P1P I 65 GND - 66 GND - 67 PEGC13-P1N O 68 PECG13-P1N I 69 PEGC13-P1P O 7[...]

Appendices Appendix C Pin Assignments C-34 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) Table C-38 System board interface connector (230-pin) (3/4) PIN No. Signal name I/O PIN No. Signal name I/O 123 PEGC04-P1P O 124 PECG04-P1P I 125 GND - 126 GND - 127 PEGC03-P1N O 128 PECG03-P1N I 129 PEGC03-P1P 130 PECG03-P1P I 131 GND - 132 GND - 133 PE[...]

Appendix C Pin Assignments Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] C-35 Table C-38 System board interface connector (230-pin) (4/4) PIN No. Signal name I/O PIN No. Signal name I/O 181 DVATX2-P3N O 182 TSDA-P3P I/O 183 GND 184 TSCL-P3P I/O 185 DVITXC-P3P - 186 GALERT-P3N O 187 DVACK-P3N - 188 GTHERM-P3N O 189 GND 190 GPUHOT-S[...]

Appendices Appendix C Pin Assignments C-36 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532) FDRUS Board C.39 CN4622 System board interface connector (12-pin) Table C-39 System board interface connector (12-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1G N D - 2G N D - 3 D- (Port 3) I/O 4 D+ (Port 3) I/O 5 USB Power - 6 U SB Power - 7 D-[...]

Appendix D Keyboard Scan/Character Codes Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] D-1 Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84[...]

Appendices Appendix D Keyboard Scan/Character Codes D-2 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29(42) | 2B AB 5 D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 3 3 D 2 0A 02 3 F 0 2 3 34 F 21 A[...]

Appendix D Keyboard Scan/Character Codes Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] D-3 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 6 0 A l t ( L ) 3 8B 81 1 F 0 1 1 * 3 61 Space 39 B9 29 F0 29 6 2 A L T ( R ) E 03 8 E 0B 8E 01 1 E 0 F 0[...]

Appendices Appendix D Keyboard Scan/Character Codes D-4 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 1 2 2 F 1 1 5 7D 7 7 8F 0 7 8 * 3 1 2 3 F 1 2 5 8D 8 0 7F 0 0 7 * 3 1 2 4 P r i n t S c * 6* 6* 6* 6 * 6 126 Pause *7 *7 *7 *7 *7 *[...]

Appendix D Keyboard Scan/Character Codes Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] D-5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 5 5 / E 0 A A E 03 5E 0 B 5 E 0 2 A E 0 F 0 1 2 E 04 AE 0 F 0 4 AE 0 1 2 7 5 I N S E 0 A A E 0 5 2 E 0 D 2 E 0 2 A E 0 F 0 1 2E 07 0E 0 F 0[...]

Appendices Appendix D Keyboard Scan/Character Codes D-6 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 7 5 I N S E 0 2 A E 05 2E 0 D 2 E 0 A A E 0 1 2E 0 7 0E 0 F 0 7 0E 0 F 0 1 2 7 6 D E L E 0 2 A E 05 3E 0 D 3 E 0 A A E 0 1 2E 0 7 1E 0 F 0 7 1E[...]

Appendix D Keyboard Scan/Character Codes Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] D-7 Table D-5 Scan codes in overlay mode Code set 1 C ode set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74[...]

Appendices Appendix D Keyboard Scan/Character Codes D-8 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co mm o n * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Appendix E Key Layout Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] E-1 Appendix E Appendix E Key Layout E.1 United Kingdom (UK) Keyboard Figure E-1 UK keyboard E.2 United States (US) Keyboard Figure E-2 US keyboard[...]

Appendices Appendix E Key Layout E-2 [CONFID ENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

Appendix F Wiring diagrams Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] F-1 Appendix F Appendix F Wiring diagrams F.1 LAN Loopback Connector Figure F-1 LAN loopback connector F.2 Printer Loopback Connector Figure F-2 Printer loopback connector[...]

Appendices Appendix F Wiring diagrams F-2 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) F.3 RS232C Loopback Connector Figure F-3 RS232C loopback connector F.4 RGB monitor Loopback Connector Figure F-4 RGB monitor loopback connector[...]

Appendix F Wiring diagrams Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] F-3 F.5 RS232C direct-connection cable (9-pin to 9-pin) Figure F-5 RS232C direct-connection cable (9-pin to 9-pin) F.6 RS232C direct-connection cable (9-pin to 25-pin) Figure F-6 RS232C direct-connection cable (9-pin to 25-pin)[...]

Appendices Appendix F Wiring diagrams F-4 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532)[...]

Appendix G BIOS rewrite procedures Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] G-1 Appendix G Appendix G BIOS rewrite procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk for the com puter t[...]

Appendices Appendix G BIOS rewrite procedures G-2 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

Appendix H EC/KBC rewrite procedures Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] H-1 Appendix H Appendix H EC/KBC rewrite procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool:  BIOS/EC/KBC rewriting disk for the c[...]

Appendices Appendix H EC/KBC rewrite procedures H-2 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

Appendix I Reliability Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] I-1 Appendix I Appendix I R eliability The following table shows MTBF (Mean Time Between Failures). Table I-1 MTBF Time (hours) MTBF 5,514[...]

Appendices Appendix I Reliability I-2 [CONFIDENTIAL] TECRA S3 Maintenance Manual (960-532)[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL] J-1 Appendix J Appendix J Maintenance of TOSHIBA RAID J.1 Outline of Maintenance (Repair) of TOSHIBA RAID Follow the below procedures to repair TOSHIBA RAID. Figure J-1 Flowchart of repairing TOSHIBA RAID *1: Refer to “Check of RAID configuratio[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-2 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) J.2 Analysis and handling by Drive Log Follow the below procedures to analyze. Figure J-2 Flowchart of Analysis and handling by Drive Log Boot the independent utility and check the Physical Drive status. (2) If necessary, analyze the Drive Lo[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-3 J.2.1 How to identify the cause of failure (1) When “Fail” or “NODRIVE” is displayed. According to “Operation of Independent utility”, boot the independent utility to display the Drive Log. To identify the failure cause of Port 0,[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-4 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) 2. Analyze the detailed data of the message of right before of “xxx Error (IN)”, “xxx Error (OUT)” (for example, “DMA Erro r (IN)”, “DMA Error (OUT)”) right before the log of “Fail this drive” message and identify the caus[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-5 Command ： Indicates Command code caused an error. The following list indicates the comma nd. Table J-1   List of Command (1/2)[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-6 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Table J-1   List of Command (2/2) LBA (Logical Block Address) : First sector address caused an error. Sector Count : Number of sectors transmitted f rom the address indicated by LBA. STATUS : Status of command. The lowest bit becom es “1?[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-7 (2) Check if it is caused by an operation miss or is a failure. To check if the cause of failure of Port1 is an operation miss or not, analyze the Drive Log of Port0. 1. In [REDUNDANT] of Port-0, find a log of “Fail this drive” message by[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-8 [CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) J.3 Operation of Independent Utility J.3.1 Outline of Independent Utility This is a utility to display Drive Log of TOSHIBA RAID. (1) Drive Log TOSHIBA RAID can store about 7,000 logs of Drive Log. TOSHIBA RAID make Drive Log redundant and st[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-9 J.3.2 How to operate the Independent Utility (1) Booting PC Connected the USB FDD to the PC to be repaired. Insert the FD storing the program of the Independent Utility in the FDD and boot the PC from the FD. The following display appears. In[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-10 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) (2) Display of Logical/Physical Drive Logical Drive The status of RAID array is displayed in Logical Drive by array. The displayed items are follows. Table J-2   Displayed item in Logical Drive Explanation Status (Status of array) Display[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-11 Physical Drive In Physical Drive, the condition of RAID array is displayed by array. The following items are displayed. Table J-3   Items displayed in Physical Drive Explanation Port Displays the port number of Serial ATA connected to the [...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-12 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) (3) Explanation of Main Menu The Independent Utility has following Main Menu. Table J-4   Item of Main Menu displayed Explanation Create Array Builds RAID array. Start Rebuild Rebuilds RAID-1. While t he rebuild is suspended, the message [...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-13 The tree of Independent Menu is as follows. Figure J-4   Tree of menu of Independent Utility[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-14 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Create Array This section explains how to select option and build array. The [Create Array] option can be selected only when there is a drive not assigned. To build array, follow the procedure below. 1. Put the cursor on [Create Array] in [[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-15 6. Put the cursor on the “DONE” and press Enter key. Pressing “OK” in [Confirmation] store the change. CAUTION: When the array is initialized, the data of drive is lost. Start Rebuild Selecting of this option starts rebuilding. [Star[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-16 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) 3. When [Rebuild Range] menu is displayed, the range to be rebuilt is designated. When [Ef fective] is selected, rebuild limit becomes valid and it rebuilds up to the rebuild limit. When [W hole] is selected, it rebuilds maxim um capacity o[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-17 8. When comp leting the rebuild, press “OK” to return to the main menu of Independent Setup Utility. Resume Rebuild During being suspended,[Resume Rebuild] is displayed in [Main Menu]. To start rebuilding suspended, follow the procedure [...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-18 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) 6. When comp leting the rebuild, press “OK” to return to the main menu of Independent Setup Utility. 7. When “Rebuild Limit” is set and [Rebuild Range] is set to [W hole], only [Finish] is can be selected after exceeding the Rebuild[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-19 Check Media This option can check if there is an error in the HDD of array. The Check Media can be done only in RAID-1. To execute Check Media, follow the procedure below. 1. Put the cursor to the [Check Media] in [Main Menu] and press Enter[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-20 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Modify Array This option changes the setting of array. Change Parameter Select [Change Parameter] in [Modify Array] menu. The following item s can be set. Table J-6   Item of array Option Explanation Write Cache Displays the setting of dr[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-21 Change RAID Level To change RAID level, select [Modify Array] menu. When changing RAID-1 (Mirroring) to RAID-0 (Striping), re fer “Changing RAID-1 to RAID-0”. When changing RAID-0 to RAID-1, refe r “Changing RAID-0 to RAID-1”. Changi[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-22 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Delete Array Selects [Delete Array] of Setup Utility and delete array. Put the cursor on the array you want to delete and press Enter key. When [Confirmation] is displayed, select “OK” to store the setting.[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-23 Physical Drive Select [Physical Drive] in Setup Utility to set physical drive. View Drive Info. Select this option in [Physical Drive] to display information of physical drive. Select the drive that you want to display in [Physical Drive] at[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-24 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) View Drive Log Select this option in [Physical Drive] m enu and select the drive that you want to display the log. At the beginning, the latest log is displayed. The 7,168 logs from the latest are recorded in detail. For the older log, only[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-25 Execute the following procedures to see the drive log in the Independent Utility. 1. Put on the cursor on [Physical Drive] in [Main Menu] and press Enter key. 2. Put on the cursor on [View Drive Log] and press Enter key. 3. Select drive that[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-26 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) The following is displayed. Table J-9   Content of Drive Log display No. Option Explanation 1 Port Displays the port number of log displayed. 2 Own/Redundant Displays if the displayed log is a log of own port (Own) or a copy of other port[...]

Appendix J Maintenance of TOSHIBA RAID Appendices TECRA S3 Maintenance Manual (960-532) [CONFIDENTIAL]] J-27 [View Drive Log] menu is as follows Table J-10   Content of View Drive Log menu Option Explanation Change Port Changes the display of the own log and redundant log. At the beginning, the Port-0’s own log and the redundant log are display[...]

Appendices Appendix J Maintenance of TOSHIBA RAID J-28 [ CONFIDENTIAL]] TECRA S3 Maintenance Manual (960-532) Exit When this option is selected, the utility is finished. W hen [Confirmation] is displayed, select “OK”.[...]