Toshiba U400 manuel d'utilisation

GMAD00167012 07/08 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 164 in this gui de. Satellite ® U400 Serie[...]

2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling . Model: Satellite ® U400 Series Recordable and/or ReWritable Drive(s) and Associated Software W arranty The computer system you purchased may in[...]

3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical applications, connections to implanted medi cal de vi ces, commercial transportation, nuclear facilities or systems or an y other applicatio ns where pr[...]

4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n. Contact either: ❖ T oshiba’ s Support W eb si[...]

5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can. In order to do this, it may occas[...]

6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your al arm equipment. If you hav e questions abou t what will disable alarm equipment, consult your telephone compan y or a qualified installer . Instructions for IC CS[...]

7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology , and is compliant to: ❖ The IEEE 802.11 Standard on W ireless LANs (Rev ision A/B/G), as defined and approv ed [...]

8 5.375 x 8.375 ver 2.3 In some situations or en vironments, the use of W ireless LAN may be restricted by the proprietor of the b uilding or responsible representativ es of the organization. These situatio ns may for e xample include: ❖ Using the W ireless LAN equipment on board airplanes, or ❖ In any other en vironment where the risk of inter[...]

9 5.375 x 8.375 ver 2.3 The term “IC” before the equipment certif ication number only signifies that the Industry Canada technical specifications were met. T o prev ent radio interference to the licensed service, this device is intended to be operated indoors an d away from windo ws to pr ovide maximum shielding. Equipment (or its transmit ante[...]

10 5.375 x 8.375 ver 2.3 The European Union WEEE (W as te from Electrical and Electronic Equipment) Directive Information The European Union WEEE (W aste from Electrical and Electronic Equipment) Directiv e is intended to protect the quality of the en vironment and human health through the responsible use of n atura l resources and the adoption of [...]

11 5.375 x 8.375 ver 2.3 Howe ver , due to differences between the individual P STNs provided in dif ferent countries/re gions the approv al does not, of itself, gi v e an unconditional assurance of successful operation on ev er y PSTN network termination point. In the ev ent of problems, y ou should contact your equi pment supplier in the first in[...]

12 5.375 x 8.375 ver 2.3 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. O F: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equipment uses a frequenc y bandwidth from 2,400 MH[...]

13 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is de pendent on what type of wi reless device is in your computer . Not all devices are avai lable on all models. Approved Countries/Regions for use for the Atheros AR5BXB72 2.4 + 5GHz 11n minicard This equipment is approv ed to the radio standard by the countr[...]

14 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries België/ Belgique: For pri vate usage outside b uildings acr oss public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for pri vate us age outside b uildings across pub[...]

15 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply . The user should use the wireless LAN utility to check the current cha[...]

16 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Atheros AR5BXB63 11g minicard This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. This device works on passive scan only. A peer -to-peer mode is not ava[...]

17 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table Albania Argentina Australia Austria Azerbaijan Bahrain Bangladesh Belgium Bolivia Bosnia[...]

18 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Intel ® PRO/Wireless 3945ABG Network Connection This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g)[...]

19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g), An Infrastructu[...]

20 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio t echnology , and is compliant to: ❖ Bluetooth Specification as def ined and approv ed b[...]

21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table. Bluetooth ® Wireless T echnology and Y our[...]

22 5.375 x 8.375 ver 2.3 In some situatio ns or en vironments, the use of Bluetooth wireless technology may be restricted by the proprietor of th e building or responsible representati ves of the organization. These situations may for example include: ❖ Using the equipment with Bluetooth wireless technology on boar d airplanes, or ❖ In any othe[...]

23 5.375 x 8.375 ver 2.3 Ta i w a n The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations. Lo w power radio frequency electric machin ery shall resist ag ainst interference from legal communications or from industrial, scientific and medical radio emis[...]

24 5.375 x 8.375 ver 2.3 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to av o[...]

25 5.375 x 8.375 ver 2.3 Optical Drive Safety Instructions This appliance contains a laser syst em and is classified as a CLASS 1 LASER PRODUCT . T o use this model prop erly , rea d th e user’ s guide carefully and keep it for your fut ure reference. Never attempt to disass emble, adjust or repair an opti cal drive. Y ou could damage the drive. [...]

26 5.375 x 8.375 ver 2.3 Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and ma y be subject to the approval of the U.S. Department of Commerce prior to expor t. Any export, directly or indirectly , in contrav ention of the U.S. Export Ad ministration Re[...]

27 5.375 x 8.375 ver 2.3 T rademarks Satellite and ConfigFree are re gistered trademarks of T oshiba Ameri ca Information Systems, Inc. and/or T oshiba Corporation. Microsoft, Outlook, Windo ws, and Wi ndo ws V ist a are either registered trademarks or trademarks of Microsoft Corporatio n in the United States and/or other countries. DirectX, Activ [...]

28 5.375 x 8.3 75 ver 2.3 Contents Introduction ................................................................................ 35 This guide ...............................................................37 Safety icons ............................................................38 Other icons used ...............................................3[...]

29 Contents 5.375 x 8.3 75 ver 2.3 Using the computer for the first time ......................49 Opening the display panel .................................49 Your computer’s features and specifications ....50 Turning on the power .......................................50 Adding memory (optional) ......................................51 Installi[...]

30 Contents 5.375 x 8.3 75 ver 2.3 Caring for your computer ........................................84 Cleaning the computer ......................................84 Moving the computer ........................................ 84 Using a computer lock ......................................85 Chapter 2: Learning the Ba sics .........................[...]

31 Contents 5.375 x 8.3 75 ver 2.3 Chapter 3: Mobile Computin g ........................... ...................... 103 Toshiba’s energy-saver design..............................103 Running the computer on battery power ..............103 Battery Notice ................................................. 104 Power management ........................[...]

32 Contents 5.375 x 8.3 75 ver 2.3 Surfing the Internet .........................................127 Internet features ..............................................128 Uploading to, and downloading files from, the Internet .....................................128 Exploring audio features .......................................129 Recording sounds [...]

33 Contents 5.375 x 8.3 75 ver 2.3 TOSHIBA Accessibility .......................................... 156 Fingerprint Authentication Utility ...........................157 Fingerprint utility limitations ...........................157 Using the Fingerprint Authentication Utility .....157 Fingerprint Logon ...........................................15[...]

34 Contents 5.375 x 8.3 75 ver 2.3 Data and system configuration backup in the Windows ® operating system ...............188 If you need further assistance ............................... 193 Before you contact Toshiba ............................193 Contacting Toshiba .........................................193 Other Toshiba Intern et Web sites [...]

35 5.375 x 8.375 ver 2.3 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go. Y our Computer model may be ENERGY ST AR ® compliant. If the model you purchased is compliant, it is labeled with the ENER GY ST AR ® log o on[...]

36 Introd uctio n 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 20% and 50% less energ y depending on how it is used. If all U.S. household and businesses replaced old computers with ne w ENERGY ST AR ® qualified models, we would save more than $1.8 billi on in energy costs [...]

37 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit T oshib[...]

38 Introd uctio n Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipment, or loss of data. These safety cautions hav e been classif ied according to the seriousness of the risk, and icons highlight t[...]

39 Introduction Other documentation 5.375 x 8.375 ver 2.3 Other documentation Y our computer comes with the following documentation: ❖ An electronic version of the user’ s guide (this document ) ❖ It may also contain guides for other programs that may come with your system. For accessory information, visit T oshiba’ s W eb site at accessori[...]

40 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information. Please read the safet[...]

41 Getting Started Selecting a place to work T o keep your computer in prime operating condition, pro tect your work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in[...]

42 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin. Read the “ A void e xtended contact between computer base/palm rest and skin” section in the “Instruction Ma[...]

43 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that cools t he CPU by drawing outside air into the computer . Always mak e sure your compute r and AC adapt or have adequa te ventilation and are protected from overheating when the power is t urned on or wh[...]

44 Getting Started Setting up your computer Please handle your computer carefully to avo id scratching or damaging the surface. Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely . The names o f windows displa yed, and the ord er in which windo [...]

45 Getting Started Re gistering your computer with T oshiba Registering your computer with T oshiba Product registration is strongly reco mmended, and allows T oshiba to send you periodic updates, announcements , and special offers applicable to your p roduct. Product registration can be completed by either visiting the T oshiba W eb site at http:/[...]

46 Getting Started Connecting to a power so ur ce Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery . Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug dire[...]

47 Getting Started Connecting to a po wer sour ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord /cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other [...]

48 Getting Started Char ging the main battery The computer’ s main battery light gi ves you an indication of the main battery’ s current char ge: ❖ Glows amber while the main battery is bei ng charged (A C adaptor connected) ❖ Glows white when the main battery is fully charged ❖ Is unlit when the main battery has d ischarged, the battery [...]

49 Getting Started Using the computer for the f irst time Battery life and charge time may var y depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Facing the front of the com puter, locate [...]

50 Getting Started Using the computer for the fir st time Small bright dots m ay appear on your screen displ ay when you turn on your computer . Y our di splay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology . An y small bright dots that may appear on your display are an intrins[...]

51 Getting Started Adding memory (optional) 3 Press and release the po wer b utton. The on/off light glows white. (Sample Illustration) T urning on the power The preinstalled operating syst em will load automatically . When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely [...]

52 Getting Started Adding memo ry (optional) Installing a memory module Memory modules can be installed in the memory module slot s on the base of the computer . Y ou will need a small Phillips scr e wdriv er for this procedure. If the computer has been running recently , the memory module may be hot. The surrounding area may also be hot. Allow the[...]

53 Getting Started Adding memory (optional) If the computer is on, begin at step 1 ; otherwise, skip t o step 3 . 1 Click Start , and then click the arrow ne xt to the lock button in the lower -right corner of the Start men u. The Shut Down menu appears. (Sample Image) Shut Down menu 2 Click Shut Down . The operating system turns off the computer .[...]

54 Getting Started Adding memo ry (optional) 6 Using a small Phillips screwdri ver , loosen the capti ve scre ws that secure the memory module slot cover . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cov er . 8 Place the scre ws and the co ver in a safe plac e so that you can retriev e them later . St[...]

55 Getting Started Adding memory (optional) If your system has the memory modules stacked on top of one another , you must remove the top module first before removing/installing the bottom module. For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. 11 Pick u[...]

56 Getting Started Adding memo ry (optional) 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on the top edge of the module to seat the module into the latches at the sides of the so cket. These latches should “snap” into place securely with th e corresponding cutouts in the side of the module. If the latche[...]

57 Getting Started Adding memory (optional) 15 Re-insert the main battery . For more information on i nserting the main battery , see “Inserting a char ged battery” on page 115 . 16 T urn the computer right side up. 17 Reconnect the cables. 18 Restart the computer . TECHNICAL NOTE: Y ou must have at least one memory module installed for the com[...]

58 Getting Started Adding memo ry (optional) The following screen may appear when you turn on the power: If “Start Windows ® Normally” is highlighted, then press Enter . If one of the Safe Mode options is highlighted, it is best to press Enter to go into Safe Mode, then shut down and restart the system, at which time Windows ® should boot bac[...]

59 Getting Started Adding memory (optional) 4 Replace the memory modu le slot cov er and secure it using the screws. 5 Re-insert the main battery . For more information on i nserting the main battery , see “Inserting a char ged battery” on page 115 . 6 T urn the computer right side up. 7 Reconnect the cables. 8 Restart the computer . TECHNICAL [...]

60 Getting Started Har d Drive Recovery Utilities Hard Drive Recovery Utilities (A vailable on certain models) Y our computer has been configured with a hard disk partitio n to allow you to recov er your hard di sk driv e or reinstall selected applications and software features or utilities. It is strongly recommended that y ou create recovery DVDs[...]

61 Getting Started Har d Drive Recovery Utilities T o create recov ery D VDs: 1 Click Start , All Programs, T oshiba, Recovery , and then Recovery Disc Creator . 2 Select DV D (to create Recovery media on D VDs). 3 Select the items you want to copy by clicking the check box next to the item’ s Name—recov ery files, applications (original bundle[...]

62 Getting Started Har d Drive Recovery Utilities Hard Disk Drive Recovery using the recover y partition Y ou hav e the options of recovering your system using the Hard Driv e Recov ery partition to the fa ctory-set default, or recov ering just your C: driv e and leaving other partitions (for example, a D: dri ve) intact, or changing the size of yo[...]

63 Getting Started Har d Drive Recovery Utilities Recovering the original factory image (recommended recovery method) Recovering a hard disk drive to its out of box state deletes all parti tions on the hard disk drive and you r information will be lost. Be sure to save your work to external media first. 1 On the T oshiba Recovery W izard screen, se[...]

64 Getting Started Har d Drive Recovery Utilities Erasing the hard disk The Recov ery W izard allo ws you to delete all data and partitions from the hard di sk. T o delete the data and partitions from your hard disk: 1 On the T oshiba Recovery W izard screen, select Erase the hard disk , and then click Next . 2 The next screen lists the tw o method[...]

65 Getting Started Har d Drive Recovery Utilities Recovering the C: partition of the HDD without changing the current partition size Recovering the C: drive to its factory default setting reformats your drive and your information on the recovered drive will be lost. Be sure to save your work to external media first. If you have created other partit[...]

66 Getting Started Har d Drive Recovery Utilities 4 Click Next to begin the restoration. Once comp lete, a message displays that the HDD has been recov ered. 5 Press any ke y on your keyboard to restart the computer . Hard Disk Drive Recovery using the Recover y media If you need to recover your computer to its default factory state, you can rebuil[...]

67 Getting Started Using the T ouchP ad™ 3 Select Manage . 4 Click Disk Managem ent . 5 Highlight the hard disk driv e in the V olume list to display its status in the lower portion of the screen. Installing drivers and applications (A vailable on certain models) The T oshiba Application Installe r (a vail able on certain models ) allo ws you to [...]

68 Getting Started Using external display de vices Scrolling with the T ouchPad ™ There are two acti ve regions on the T ouchPad ™ that allo w you to scroll as you would with any wheel de vice on a mouse or trackball. T o scroll vertically , run your finger up or do wn along the right edge of the T ouch Pad. T o scroll horizontally , run your f[...]

69 Getting Started Using external display de vices 4 T urn on the external de vice. Y our computer will automa tically detect the external display devic e and acti vate a scr een with di splay options. 5 Select the settings you desire and click Ap p l y . 6 Click OK . In the future you can change the display settings by pressing Fn + F5 , or by con[...]

70 Getting Started Using external display de vices The quickest way to change the display output settings is to use the display hot key ( Fn + F5 ): 1 While holding down Fn , press F5 repeatedly until the setting you want takes ef fect. Briefly pause each time you press the F5 ke y to allow time for the display to change. This hot key c ycles throu[...]

71 Getting Started Using an external k e yboard Adjusting the quality of the external display T o obtain the best picture quality from you r television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps. Using an external keyboard If you prefer to use a f[...]

72 Getting Started Connecting a printer T o connect a printer to your computer: 1 Connect the printer cable to th e printer and then connect the other end to one of the computer’ s USB ports. 2 Plug the printer’ s power cable into a li ve A C outlet. Setting up a printer Some printers require a specific installation process. Refer to your print[...]

73 Getting Started Connecting an optional external disk ette drive Connecting an optional external diskette drive Some operations, such as creati ng a password service disk ette, require a diskette dri ve designed for use with 3.5-inch diskettes. (Sample Illustration) Optional external USB diskette drive T o connect an optional external USB disk et[...]

74 Getting Started T urning off the computer Options for turning off the computer Depending on the operating sy stem installed, you have more than one option av ailable for turning off the computer: Shut Down, Hibernate, and Sleep. Each option has its advantages. ❖ Use the Shut Down or Hibernate command if you will not be using the computer for s[...]

75 Getting Started T urning off the computer For information on ho w to use and configure Hibernation mode see “Using and configuring Hibernatio n mode” on page 78 . Sleep mode The Sleep command places the comput er into a power -saving mode. Sleep sa ves the current state of the computer to memory so that, when you restart the comp uter , you [...]

76 Getting Started T urning off the computer Using the Shut Down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns off your computer . Use the following steps to turn of f your co[...]

77 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. (Sample Image) Advanced settings tab of P ower Options scr een 4 Click Power buttons and lid to display the actions that you can configure. 5 Select the options you want from the drop-down lists. Thes[...]

78 Getting Started T urning off the computer 6 Click App l y . 7 Click OK . Once the computer is conf igured, you can turn it off b y either pressing the power b utton or closing th e display panel, depending on the options set . Restarting your computer T o start the computer up again, press the po wer b utton unti l the on/off light glows white. [...]

79 Getting Started T urning off the computer Configuring Hibernation mode options Y ou can place the computer into Hibernation mode by either pressing the power b utton or closing the display panel. Y ou can also specify an amount of time after which the computer automatically goes into Hibernation mode. T o use any of these methods, you f irst nee[...]

80 Getting Started T urning off the computer 4 Click Power buttons and lid to display the actions that you can configure. 5 Select Hibernate for the options you want. These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Hibern[...]

81 Getting Started T urning off the computer Using and configuring Sleep mode T o turn off the com puter using the Sleep command: 1 Click Start , and then click the arro w ne xt to the Lock button in the lower -right part of the Start menu. The Shut Down menu appears. (Sample Image) Shut Down menu 2 Click Sleep . The computer sa ves the status of a[...]

82 Getting Started T urning off the computer 2 Click Change pl an settings under the power plan to be customized. The Edit Plan Settin gs window appears. (Sample Image) Edit Plan Settings screen 3 T o change the amount of time af ter which the computer ent ers Sleep mode: ❖ Under Put the computer to sleep , select the desired amount of time in bo[...]

83 Getting Started T urning off the computer 5 Click Power buttons and lid to display the actions that you can configure. 6 Select Sleep for the options you want. These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Sleep if y[...]

84 Getting Started Customizing your comp uter’ s settings Customizing your computer’ s settings There are sev eral ways in which you can customize your computer to suit your particular requir ements. Refer to your operat ing system documentation or Help and Su pport for details. Y ou may also wish to customize your power usage settings. F or mo[...]

85 Getting Started Caring for your computer Using a computer lock Y ou may want to secure your comput er to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com . (Sample Illustration) Computer lock cable T o secure[...]

86 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive. If the netw ork you are using goes down and you must restart your [...]

87 Learning the Basics Computing tips ❖ Back up your files to disks (or other remov able media) on a regular basis. Label the backup co pies clearly and store them in a safe place. It is easy to put of f backing up because it takes time. Ho wev er , if your internal storage drive suddenly fails, you will lose all the data on it unless you hav e a[...]

88 Learning the Basics Using the ke yboar d Using the keyboard Y our computer’ s ke yboard contai ns character keys, control ke ys, function ke ys, and special W indo ws ® ke ys, providing all the functionality of a full-size keyboard. (Sample Illustration) Ke yboar d Character keys T y ping with the character keys is very much like typing on a [...]

89 Learning the Basics Using the ke yboar d Ctrl, Fn, and Alt keys (Sample Illustration) Ctrl, Fn, and Alt keys The Ctrl , Fn , and Alt keys do different things depending on the program you are using. For more inform ation, see your prog ram documentation. Function keys The function k eys (not t o be confused with the Fn key) are the 12 keys at the[...]

90 Learning the Basics Using the ke yboar d Overlay keys The ke ys with gray numbers and symbols on the front of them form the numeric and cursor ov erlay . This ov erlay lets you enter numeric data or control the cursor as you would using the 10-key ke ypad on a desktop comput er’ s k eyboa rd. (Sample Illustration) Numeric and cursor contr ol o[...]

91 Learning the Basics Starting a pr o gram Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. T o find the file, use the Start menu or W indo ws ® Explorer . If you prefer to open the program f i rst, you hav e four options. Y ou can: ❖ Double-click th[...]

92 Learning the Basics Starting a pr ogr am Starting a program from Windows ® Explorer If a program is not listed in th e All Programs menu, yo u can start it from W indows ® E xplorer . W indo ws ® Explorer gi ves you a vie w of your computer’ s contents as a hi erarchy or “tree. ” Y ou can easily see the contents of each driv e and folde[...]

93 Learning the Basics Saving your work Starting a program using the Start Search field This example uses the Start menu’ s Start Search f ield to start Wo r d P a d : 1 Click Start to display the Start menu. The Start Search f ield appears at the bottom of the Start menu. (Sample Image) Start Sear ch field in Start menu 2 Start typing the progra[...]

94 Learning the Basics Saving your work Saving files 1 In your Windo ws ® -based application, click File , and then Sav e . 2 Click Browse f olders . If you are working with a docum ent that already has a f ile name, this i s all you need to do. If you created a new document, your program displays a Sav e As dialog box. Use this dialog box to spec[...]

95 Learning the Basics Printing your work Using a file extension Most programs assign an extension to the f ile name that identifies the file as being created in the pr ogram with a particular format. F or example, Microsoft ® W ord saves f iles with a .doc extension. Any file name with an extension of “.doc” is assumed to be a Microsoft ® W [...]

96 Learning the Basics Backing up your work 3 Specify the print parameters. For e xample, the range of pages and number of copies to print. 4 Click Print . Backing up your work Back up all the files you create in case something happens to your computer . Y ou can back up your files to dif ferent types of media such as CDs, D VDs, diskettes, or to a[...]

97 Learning the Basics Using the optical drive TECHNICAL NOTE: Y our optical drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region. The drive will allow you to change regions four times. On the fourth change, the region will b[...]

98 Learning the Basics Using the optical drive Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Media control buttons The media control buttons located on the system control panel above the keyboard let you mute the sound and play audio CDs or D VD movies when the computer is on. (Sam[...]

99 Learning the Basics Using the optical drive 4 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty , clean it as described in “Caring for optical discs” on page 102 . 6 Place the disc carefully in th e disc tray , label side[...]

100 Learning the Basics Using the optical drive 8 Make sure the disc is completely on the spindle and is lying flat on the tray . If you insert the disc incorrectly , it may jam the drive. If this happens, contact T oshiba support for assistance. 9 Push the disc tray in by pressing gently on th e center of the tray until it clicks into place. Y ou [...]

101 Learning the Basics Using the optical drive Recording optical media Depending on the configuration, your computer may come with an optical driv e that allo ws you to: ❖ Play pre-recorded and recorded optical media. ❖ Read/write data and multi-m edia files to recordable optical media. For more information regarding supported optical media fo[...]

102 Learning the Basics T oshiba’ s online r esour ces Removing a disc with the computer off T o remov e a disc with the computer turned of f: 1 Insert a slender object, such as a straightene d paper clip, into the manual eject hole. The disc tray slides partially out of t he driv e (about 1 inch). Never use a pencil to press the manual eject but[...]

103 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your comput er while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process. It has a number of other features that enhanc e its energy ef ficiency .[...]

104 Mobile Computing Running the computer on battery power Battery Notice Battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as th e natural performance variations produced by the design of individual components. Published battery l[...]

105 Mobile Computing Char ging ba tteries Power management Y our computer ships with t he power management options preset to a configuration that will prov ide the most stable opera ting en vironment and optimum system performan ce for both A C power and battery modes. Changes to these settings may result in system performance or stability issues. [...]

106 Mobile Computing Char ging batteries Charging the main battery T o charge the main battery while it is in your computer, plug the computer into a li ve electrical ou tlet. The battery char ges whether the computer is on or off. TECHNICAL NOTE: The recharging of the batter y cann ot occur when your computer is using all of the pow er provided by[...]

107 Mobile Computing Monitoring main battery power If the R TC battery is lo w , the real-time clock and calendar may display the incorrect tim e and date, or stop working. T o recharge the R T C battery , plug th e computer into a li ve electrical outlet and leav e the computer powered on for 24 hours. It is seldom necessary to charge the RTC batt[...]

108 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the battery light ( ) with the on/off light ( ). When the on/off light flashes amber , it indicates that the system is suspended (using the Windows ® operating system Sleep command). (Sample Illustration) P ower and batt ery light locations Determining remaining ba[...]

109 Mobile Computing Monitoring main battery power Highlight the power icon in the Notification Area. A pop-up message displays the remaining battery power as a percentage. W ith repeated discharges and rechar ges, the battery’ s capacity gradually decreases. A frequently us ed older batt ery does not power the computer for as long as a new batte[...]

110 Mobile Computing Monitoring main battery power T o change the default notification settings: 1 Click Start , Control Panel , Mobile PC , and then Po wer Options . The Po wer Options window appears. 2 Click Change pl an settings under the power plan to be customized. The Edit Plan Settin gs window appears. 3 Click Change advanced power settings [...]

111 Mobile Computing Monitoring main battery power There are v arious ways in which you can conserv e power a nd extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves po wer when you turn of f the computer and turn it back on again ❖ Use the W indows ® po wer-sa ving option plans These power -saving options cont[...]

112 Mobile Computing Monitoring main battery power T o edit a plan or to edit advanced settings, continue to the following steps. 4 Click Change Pl an Settings to choose the plan you want to edit. This screen allows you to change basic settings. 5 Click Change Adv anced Se ttings to access settings for battery notification lev els, inte rnal storag[...]

113 Mobile Computing Changing the main battery 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Po wer Plan options are: Balanced, Power Sa ver , and High Performance. 3 Release the Fn key . The hot key card disappears. Y ou are now in the selected mode. Changing the main batter y When your main bat tery has ru[...]

114 Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlo cked position. (Sample Illustration) Unlocking the battery r elease loc k 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer . (Sample Illustration) Removing the battery If the battery is leaking or i[...]

115 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks. The battery pack has been designe d so that you cannot install i t with rev erse polarity . [...]

116 Mobile Computing T aking car e of your battery 4 T urn the computer right side up. 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 113 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life. S[...]

117 Mobile Computing Disposing of used batteries Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing[...]

118 Mobile Computing Disposing of used b atteries Never attempt to dispose of a battery pack by burning or by throwing it into a fire, and never allow exposure to a heating a pparatus (e.g., microwave oven). Heat can cause a battery pack to explode and/or release caustic liquid, both which may possibly cause serious injury . Always dispose of used [...]

119 Mobile Computing T raveling tips T raveling tips The en vironmental precautions listed in “Selecting a place to work” on page 40 , also apply while traveling. ❖ Nev er leav e your computer on a sunny ledge or in a place where it could get wet or covered in dust. ❖ Always tra vel with the comput er in a carrying case. T oshiba of fers a [...]

120 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system. Y ou use i ts features to start programs, find documents, set up system components, and perfor[...]

121 Exploring Y our Computer’ s Features Exploring the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, T askb ar , Notification Area, and background pattern. (Sample Image) W indows ® oper ating system deskt op Icons An icon represents a folder , file, or program t[...]

122 Exploring Y our Computer’ s Features Explorin g the desktop Y our desktop may contain othe r icons depending on your configuration. See W indo ws ® online Help for more specific information on each icon and ho w to use it. Start button Y ou use the Start button to: ❖ Start programs ❖ Open documents ❖ Adjust system settings ❖ Find fil[...]

123 Exploring Y our Computer’ s Features Setting up for communications Setting up for communications T o connect to the Internet, use an online service, or communicate across the telephone lines with another computer , you need: ❖ A browser or communications program ❖ An Internet Service Pro vider (ISP ) or online service if you plan to use t[...]

124 Exploring Y our Computer’ s Features Setting up for communications Accessing a network T o access a network: ❖ At the of fice, c onnect an Ethern et cable to the RJ45 jack on your computer . For specific info rmation about connecting to the network, consult your network administrator . Many hotels, airports, and of fices of fer W i-Fi ® ac[...]

125 Exploring Y our Computer’ s Features Setting up for communications For more detailed i nformation regarding your computer’s modem, visit T oshiba’ s W eb site at accessories.toshiba.com . Before you can communicate using th e modem, you need to connect it to a telephone line. Y ou r computer’ s b uilt-in modem port provides an RJ-11 jac[...]

126 Exploring Y our Computer’ s Features An overview of using the Internet An overview of using the Internet The following sections gi ve a quick introduction to the Internet and some of its exciting featur es, under these headings: ❖ The Internet ❖ The W orld Wi de W eb ❖ Internet Service Providers ❖ Connecting to the Internet ❖ Surfin[...]

127 Exploring Y our Computer’ s Features An overview of using the Internet Connecting to the Internet T o connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A W eb browser ❖ An Internet Service Provider (ISP) account Once you hav e established an ISP account, you can connect to the Internet. 1 Connect you[...]

128 Exploring Y our Computer’ s Features An overview of using the Internet Internet features The Internet offers man y types of communication tools to help you perform many tasks. ❖ Internet email T o send and recei ve email of yo ur o wn, you need a mailbox on the W eb or an email address. If you hav e an account with an ISP , you can probably[...]

129 Exploring Y our Computer’ s Features Explori ng audio feat ur es Exploring audio features Y ou can use your computer to record sounds usi ng the computer’ s internal microphone (av ailable on certain models) or an optional external microphone. Y ou can listen to sound f iles or audio CDs using the built-in speakers, headphones, or external [...]

130 Exploring Y our Computer’ s Features FM tuner TECHNICAL NOTE: When using amplified speakers, use speakers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer . T o play back sound files through e xternal speakers or headphones: 1 Locate the headphone jack on the computer . 2 Usi[...]

131 Exploring Y our Computer’ s Features We b C a m e r a We b C a m e r a (A vailable on certain models) Y our computer may come with a built-in W eb Camer a. W ith this W eb Camera you can do the following: ❖ T ake pictures and record videos with your computer ❖ Chat with others and have them see you while using instant messaging (IM) progr[...]

132 Exploring Y our Computer’ s Features Using an Expr essCard ® 2 Insert the ExpressCard. (Sample Illustration) Inserting an ExpressCar d 3 Push the ExpressCard into the sl ot until it locks in place. Removing an ExpressCard ® 1 Prepare the card for remov al by clicking the Sa fely Remove Hardwar e icon in the Notification Area and then select[...]

133 Exploring Y our Computer’ s Features Using the Bridge Media Adapter Slot Using the Bridge Media Adapter Slot (A vailable on certain models) The Bridge Media Adapter slot (av ailable on certain models) supports the use of Memory Stick ™ , Memory Stick ™ PR O, Secure Digital ™ (SD ™ ), MMC ™ (MultiMediaCard ™ ), or xD-Picture Card ?[...]

134 Exploring Y our Computer’ s Features Using the i.LINK ® port Removing memor y media 1 Prepare the media for remo v al by clicking the Safely Remo ve Hardwar e icon in the Notification Area and then selecting the card or device you w ant to remove. If the system is unable to prep are the media for safe remova l, a message will tell you to try[...]

135 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help you to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change de fault options. These utilities are described in this chapter . The utilities described in this[...]

136 Utilities TOSHIB A Assist ❖ TOSHIB A Accessibility ❖ Fingerprint Authentication Utilit y ❖ ConfigFree® TOSHIBA Assist The TOSHIB A Assist pro vides qui ck access to computer functions and allows you to customize a range of com puter settings. T o access TOSHIB A Assist, click Start , All Programs , To s h i b a , Utilities , and then TOS[...]

137 Utilities TOSHIB A Assist Connect The features av ailable in this category are: ❖ ConfigFree ® Connectivity Doctor ❖ Bluetooth ® Settings ❖ Bluetooth ® Local COM Setting s (Sample Image) T OSHIBA Assist window – Connect tab[...]

138 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secure tab[...]

139 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility (Sample Image) T OSHIBA Assist window – Pr otect & F ix tab[...]

140 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ TOSHIB A Hardware Setup ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ CD/D VD Dri ve Acoustic Silencer ❖ TOSHIB A Accessibility ❖ TOSHIB A SD™ Memory Card Format Utility (Sample Image) T OSHIBA Assist window – Optimize[...]

141 Utilities TOSHIB A Applicati on Installer TOSHIBA Application Installer (A vailable on certain models) The TOSHIB A Application Installer allows you to reinstall the dri vers and applications that were originally bundled with your computer . T o reinstall driv ers and applications: 1 Click Start , All Programs , To s h i b a , Recovery, and the[...]

142 Utilities Setting passwor ds Setting passwords Setting a password lets you walk away from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can wo rk on your computer again. T oshiba supports se ve ral types of passwords on you r computer: ❖ An instant password?[...]

143 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, T oshiba strongly recommends that you save your password in a location where you can later access it should you not r[...]

144 Utilities Setting passwor ds 6 Click OK . A pop-up screen ap pears asking for the User Password Mode. 7 Select whether the user password allo ws the user to change the hardware configuration: ❖ Able to run HwSetup —User can change the hardware configuration ❖ Unable to run HwSetup — User cannot change the hardware conf iguration (superv[...]

145 Utilities Setting passwor ds T o register a password for the po wer- on password functions: 1 Click Start , All Programs , To s h i b a , Utilit ies , and then TOSHIB A Assist . The TOSHIB A Assist windo w appears. 2 On the left side, click the Secure tab . 3 Click the User Password icon. The Password tab of the TOSHIB A Hardware Setup windo w [...]

146 Utilities TOSHIB A PC Dia gnostic T ool Utility 4 Click Not Registered. A pop-up screen ap pears asking for a password. 5 Enter the user password, then click OK . TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose pro blems with devices in your computer . Refer to the online Help documentatio n within the application for additi[...]

147 Utilities TOSHIB A SD™ Memory Car d F ormat Utility TOSHIBA SD ™ Memor y Card Format Utility This utility is used to for mat SD ™ cards used with the Bridge Media Adapter slot. T o format an SD memory car d using this utility : 1 Click Start , All Programs , To s h i b a , Utilit ies , and then SD Memory Card F ormat . The TOSHIB A SD Mem[...]

148 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contr ol Panel , and then Mouse under Hard ware and Sound , or click the Mouse icon in the Optimize tab of TOS HI BA A ssi s t . The Mouse Properties screen appears. (Sample Image) Mo[...]

149 Utilities TO S H I B A H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the T oshiba con figuration management tool av ailable through th e W indows ® operating system. T o access it: ❖ Click Start , All Programs , To s h i b a , Utilit ies , and then HWSetup , or clic k the TOS HI BA H ar dw are S et u p i con in th[...]

150 Utilities TO S H I BA H a rd w a re S e t u p ❖ Display —Allows you to change various default settings for the built-in display When the computer restarts, it remembers the last configuration. If data does not appear on the display you are using after starting in Sleep Mode, press Fn + F5. For more information, see “Directing the display [...]

151 Utilities TO S H I B A H a rd w a re S e t u p ❖ The “USB Sleep and Charge function” only works for compatible ports. ❖ When “USB Sleep and Charge function” is Enabled, USB bus power (DC 5V) will be supplied to compatible ports even when the power of the computer is turned OFF . ❖ USB bus power (DC 5V) is similarly supplied to the[...]

152 Utilities TO S H I BA H a rd w a re S e t u p If the function does not work with Mode-1 setting, change it t o Mode-2. Some external devices may not be able to use t his function in either mod e. When this happens, chang e the setting to Disabled. Setting item: Enabled (Mode-1) -- Enables th e function Enabled (Mode-2) -- Enables th e function [...]

153 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 209 ). Y ou may select all applications or any subset of the following: ❖ Microsoft ® Internet Explorer ® ❖ Microsoft ® Of f ice ❖ W indo [...]

154 Utilities TOSHIB A Button Support T o zoom in, hold down the Fn key and press 2 ; to zoom out, hold down the Fn ke y and press 1 . For more information about how to use the T OSHIBA Zooming Utility , right-click the icon in the Notification Area and then click Help . TOSHIBA Button Support TOSHIB A Button Support allows you to customize the Mut[...]

155 Utilities CD/D VD Drive Acousti c Silencer CD/DVD Drive Acoustic Silencer This utility can slow the speed of your optical driv e to make it run more quietly . Y ou can use this utility to m ake listening to music CDs more enjoyable. When you change the optical drive to “Silence” mode, the setting is only valid for the current Windows ® ses[...]

156 Utilities TOSHIB A Accessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot ke y combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a sti cky key , meaning you can press it once, re[...]

157 Utilities F ing erprint Au thentication Utility Fingerprint Authentication Utility (A vailable on certain models) The fingerprint authentication utility (av ailable on certain models) can be used to replace the ke yboard-based user password authentication syst em when booting up. The fingerprint authentication uti lity can also be us ed for use[...]

158 Utilities F ing erprint Au thentication Utility Fingerprint Logon The fingerprint utility enables logon to your comp uter using fi ngerprints. During us er enrollment, f ingerpr int samples are sa ved and associated with the user’ s W indows ® user account. When the user attempts to log on again, th e user’ s fingerprint is read and compar[...]

159 Utilities F ing erprint Au thentication Utility ❖ A void the follo wing finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the f ingerprint recognition success rate. ❖ Soaked or swollen finger (e.g., after taking bath) ❖ Injured finger ❖ We t f i n g e r ❖ Soiled or oily f [...]

160 Utilities ConfigF r ee® ❖ The recognition success rate may dif fer from user to user . ❖ T oshiba does not guarantee that th is fingerprint recognition technology will be error -free. T o shiba does not guarantee that the f ingerprint reader will recognize the enrolled user or accu rately screen out unauthorized users at all times. T oshib[...]

161 Utilities ConfigF r ee® Starting ConfigFree ® T o start ConfigFree ® , be sure the com puter has a wired or wireless connection. Then perform any of the follo wing steps: ❖ Click Start , All Programs , To s h i b a , Networking , and then Conf igFree . ❖ Double-click the Config Free ico n in the Notification Area. ❖ Press the TOSHIB A [...]

162 Utilities ConfigF r ee® ❖ Status of W ireless Connection switch (Sample Image) Connect ivity Doctor scr een Profile Settings The Prof ile Settings utility lets you save network settings in “profiles . ” ConfigFree ® prof iles are useful for easily switching network settings an d devices. Y ou can switch network settings simply by select[...]

163 Utilities ConfigF r ee® T o create a profile: 1 Click the icon in the Notif ication Area. 2 Mov e the pointer to Prof ile . 3 Click Open Settings . The ConfigFree Prof ile Settings windo w appears. (Sample Image) ConfigF ree Pr ofile Settings windo w 4 Click Add to start the Create Prof ile W izard.[...]

164 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter when using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself. It cov ers the problems you are most lik[...]

165 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask . Closing the failed prog ram should allow you to continue working. If it does not, c[...]

166 If Something Goes Wrong Pr oblems when you turn on the computer If you are using an A C adaptor , v eri fy that the computer is recei ving power from the external po wer source by looking at the A C power light. If the indicator is glo wing, th e computer is conn ected to a liv e external po wer source. The computer starts but when y ou pr ess [...]

167 If Something Goes Wrong Pr oblems when you turn on the computer If you are running on battery power , it is recommended that you do not lea ve the computer in Sleep mode for lo ng periods of time. T o charge the battery , leave the computer plugged into a liv e wall outlet for sev eral hours. For more information see “Charging batteries” on[...]

168 If Something Goes Wrong The W indo ws ® operating system is not working 5 V erify that the A C adaptor is th e correct unit for your computer model. The computer may not be abl e to start from an A C adaptor that is rated for less current (amperage) than the computer requires, e ven if the rated v oltage is correct, and the plug fits correctly[...]

169 If Something Goes Wrong The W indows ® operating system is not working ❖ Safe Mode with Command Pr ompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Kno wn Good Conf iguration (adv anced) ❖ Directory Services Restore Mode ❖ Deb uggin g Mode ❖ Disable automatic restar t on system failure ❖ Disable Driv er[...]

170 If Something Goes Wrong Resolving a hardwar e conflict The Windows ® operating system can help you If the operating system has started properly but you still ha ve a problem using your co mputer , the online Help can assist you in troubleshooting the problem . T o access the W indo ws ® operating system Hel p and Support: 1 Click Start , then[...]

171 If Something Goes Wrong Resolving a har dwar e conflict The device most recently connected to the system is th e one most likely to be causing a conflict. Resolving conflicts There are sev eral things you can do to resolve hardw are conflicts: ❖ Get the most recent dri vers from the manuf acturer . ❖ Disable the device. For an ol der de vic[...]

172 If Something Goes Wrong Resolving a hardwar e conflict ❖ The Resources tab, which lists resources assigned to the monitor , optional external optical drive, optional external diskette dri ve, and other power -using functions. This tab does not appear if the device is not using resources. ❖ The Driver tab, which displays th e dri vers being [...]

173 If Something Goes Wrong Resolving a har dwar e conflict For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. Power and the batteries Y our computer receive s its po wer through the A C adaptor and power cord/cable or from the system batteries (battery , o[...]

174 If Something Goes Wrong Resolving a hardwar e conflict The battery appears not to power the computer f or as long as it usually does. If you frequently repeat shallow char ge and disch a rge, the battery meter may become in accurate. Let the battery discharge completely , then try charging it ag ain. Check the po wer options vi a your Po wer Pl[...]

175 If Something Goes Wrong Resolving a har dwar e conflict Nothing happens when you p ress the ke ys on the external keyboard. Y ou may hav e plugged the external keyboard in while the computer was turned on. Using the computer’ s T ouchPad: 1 Click Start , and then click the arro w ne xt to the Lock button in the lower -right part of the Start [...]

176 If Something Goes Wrong Resolving a hardwar e conflict ❖ T ry adjusting the contrast and brightness controls on the external monitor . ❖ Press Fn and F5 simultaneously to make sure the display priority is no t set for the built-in screen. The screen does not look right. Y ou can change the display settings by clicking a blank area of the de[...]

177 If Something Goes Wrong Resolving a har dwar e conflict Small bright dots appear on yo ur TFT display when y ou turn on y our compu ter . Small bright dots m ay appear on your screen displ ay when you turn on your computer . Y our di splay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precisio[...]

178 If Something Goes Wrong Resolving a hardwar e conflict 6 Y ou can choose one or both options: ❖ Automatically f ix f ile system er rors ❖ Scan for and attempt reco very of bad sectors 7 Click Start . Error- checking tests and repairs the disk. Y our hard disk seems very slo w . If you hav e been using your computer fo r a long time, your fi[...]

179 If Something Goes Wrong Resolving a har dwar e conflict Optical drive problems Y ou cannot access a disc in the dri ve. If the optical dri ve is an e xternal driv e, make sure that the driv e’ s cable is properly connected to the computer . Make sure the tray that holds the optical disc is closed properl y . Press gently until it clicks into [...]

180 If Something Goes Wrong Resolving a hardwar e conflict The disc will not come out of the dri ve when y ou click the eject button on the scr een. Press the b utton on the optical dri ve itself. Fo r additional information see “Y ou press the disc eject button, b ut the dri ve tray does not slide out. ” on page 179 . Sound system problems No [...]

181 If Something Goes Wrong Resolving a har dwar e conflict ExpressCard ® checklist ❖ Make sure the card is insert ed properly into the slot. ❖ Make sure all cables are securely connected. ❖ Occasionally a defecti ve ExpressCard ® slips through quality control. If another computer wit h a ExpressCard slot is av ailable, try the card in that[...]

182 If Something Goes Wrong Resolving a hardwar e conflict 3 Select the item you wish to remove and click OK . 4 Remov e the device when told it is safe to do so. Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported. For more information on Hibernation and Sleep modes see ?[...]

183 If Something Goes Wrong Resolving a har dwar e conflict T ry printing another file. For exam ple, you could create and attempt to print a short test file using Notepad. If a Notepad file prints correctly , the problem may be in yo ur original file. If you cannot resolve the problem, contact the printer’ s manufacturer . The printer will not p[...]

184 If Something Goes Wrong Resolving a hardwar e conflict Wireless networking problems This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi ® ) networking. The terms and concepts used assume a bas ic understanding of networks, and may be for more advanced users. If you need assistance or if you [...]

185 If Something Goes Wrong Resolving a har dwar e conflict ❖ V erify that the network connection is configured to obtain its Internet Proto col (IP) address dynamically: 1 Click Start , and then Network . 2 Click V iew Status . 3 Click Details . 4 V e rify that the DHCP E nabled setting is set to Ye s . 5 Click Close . ❖ Use IPCONFIG to verify[...]

186 If Something Goes Wrong D VD operating pr oblems The Windo ws ® operating system wireless management facility does not work. If you are using an external W i-Fi ® adapter (an ExpressCard ® , USB adapter , or other variety), check if the adapter comes with its o wn management utility . If it does, the utility may be disabling the W indows ® [...]

187 If Something Goes Wrong Develop good computing habits 3 Select Never on When to turn of f the display . 4 Click Sav e changes . The screen sa ver runs while y ou ar e watching a movie or title. If the screen sav er is enabled, it runs on top of any movie or title you are watching. T o disable the screen sa ver: 1 Right-click on the desktop and [...]

188 If Something Goes Wrong Develop good computing habits Read the user’ s guides. It is very dif ficult to provide a f ail-safe set of steps you can follow ev ery time you experience a problem with the computer . Y our ability to solve problems will improve as you learn about how the computer and its software work together . Get familiar with al[...]

189 If Something Goes Wrong Develop good computing habits 4 In the input field, enter a name that is descripti ve enough to be easily understood in the future, such as “Before installin g Brand X Accounting app. ” Then click Create . 5 The W indo ws ® operating system creates the Restore Point, automatically stamps it with the current date and[...]

190 If Something Goes Wrong Develop good computing habits Backing up your data or your entire computer with the Windows ® operating system The most v aluable component of y our computer system is the data you create and store on its internal storage drive. Since problems with either hardware or softw are can make the data inacces sible or ev en de[...]

191 If Something Goes Wrong Develop good computing habits General tips for installing hardware and software Here are a fe w tips to help ensure safe and easy installation of ne w hardware (printers, pointing devices, e xternal hard drives, D VD writers, scanners, etc.) and software (applications like Microsoft ® Of fice and Adobe ® Photoshop ® ,[...]

192 If Something Goes Wrong Develop good computing habits 3 Install one it em of hardware or software. 4 Restart the W indo ws ® operating system. 5 Use the new hardw are or software for a while, noting any new problems. Mak e sure that your critical applications (e- mail, business applications, etc.) are w orking correctly , and verify that impor[...]

193 If Something Goes Wrong If you need further assistance Before connecting the eSA T A device to your computer and external power source, read the documentation that ca me with the device and follow the manufacturer’ s instructions. If you need further assistance If you have follo wed the recomm endations in this chapter and are still having pr[...]

194 If Something Goes Wrong Other T oshiba Internet W eb sites T oshiba voice contact Before calling T o shiba, make sure you have: ❖ Y our computer’ s serial number ❖ The computer and any optional devices related to the problem ❖ Backup copies of your W indows ® operating system and all other preloaded software on your choice of media ❖[...]

195 If Something Goes Wrong T oshiba’ s worldwide of fices For more information on additional T osh iba worldwide locations, please visit: www .toshi ba.co.jp/ index. htm . France T o shiba Systèmes (France) S.A. 7, Rue Ampère; B. P . 131 92800 Puteaux Cédex France Germany T oshiba Europe GmbH Leibnizstraße 2 D-93055 Regensbu rg Germany Italy[...]

196 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards prov ide a quick way to modif y selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot K ey Cards and Application Cards. Hot Key Cards The Hot Ke y Cards are used to set or modify the following system functions: ❖ M[...]

197 Hot Keys /TOSHIBA Ca rds Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off. Hot keys have a legend on the key indicating the option o[...]

198 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 136 . PC Diagnostic T ool utility For more information, refer to “TOSHIB A PC[...]

199 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Using the Application Cards T o launch an application using the Application Cards: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen. (Sample Image) TOSHIB A Car d display 2 Click the “stacked” card on the far right of the display . The Applica[...]

200 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 3 The Card Case displays tw o rows of Cards. Cards that appear solid (not tr ansparent) in the bottom ro w are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards . 4 T o enable a card, drag it from the top row to the[...]

201 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer . or Fn + This TOSHIB A Card or hot ke y blanks the display . Selecting th[...]

202 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window . Selecting this Card or pressing the hot[...]

203 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep mod e” on page 81 . Selecting this Card or pressing the hot ke y displays the following options: (Sample Imag[...]

204 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernatio n mode” on page 78 . Selecting th[...]

205 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the power - o n d i s pl a y o p t i o ns (only the first option is av ailable when you do not have an external monitor attached) (the last option is available only if you are in Ex tended Display Mode)[...]

206 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-i[...]

207 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices* installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the Wi-Fi ® module. ❖ Bluetooth ® enabled—Enables just [...]

208 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T o uchPad. For more information on using the T ouchPad, see “Disabling or enabling the T ouchPad™” on page 68 . Selecting this Card or pressing the hot key displays the follow[...]

209 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution. Selecting this Card or pressing the hot ke y displays the following options: (Sample Image) Scr een r esolution options Cycle through the screen resolutio ns, then select the[...]

210 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot k ey turns the curs or control overlay on and off. Fn + This hot k ey turns the numeric overlay on and of f. Fn + This hot k ey turns the scroll lock feature on and off. Fn + This hot key tu rns the T OSHIB A Z oo mi n g Utility to zoom-out.[...]

211 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our c omputer ships with the corr ect po wer supply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world. USA and Canada UL ap prove d CS A a pp roved United Kingdom BS ap pr oved Australia [...]

212 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide. AC alternating current BIOS basic input/output system bps bits per second CD compact disc CD-R OM compact disc read-only memory CD-R W compact disc re write memory CMOS co[...]

Glossary 213 DOS disk operating system DPI dots per inch DSTN dual supertwist nem atic DV D digital versatile (or video) disc DV D - R O M digital versatile (or video) disc read-only memory ECP enhanced capabilities po rt EPR OM erasable programmable read-only memory FAT f ile allocation table FCC Federal Communicat ions Commission GB gigabyte HDD [...]

214 Glossary SDRAM synchronous dynamic random access memory SRAM static random access memory SSD Solid State Driv e SV GA super video graphics adapter TFT thin film transistor USB univ ersal serial b us URL uniform resource lo cator WA N wide area netw ork www W orld Wide W eb Te r m s The follo wing terms may appear in this user’ s guide. A acti[...]

Glossary 215 baud rate — The speed at which a comm unication de vice, such as a printer or modem , transmits info rmation. Baud ra te is the number of signal changes per second (not necessarily th e same as bits per second). See also bits per second . BIOS (basic input/ output system ) — Basic instructions, stored in read- only memory (R OM), c[...]

216 Glossary central processing unit (CPU) — The chip that functions as the “brain” of the computer . It takes informa tion from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character — Any letter , number , or symbol you can use on the compu[...]

Glossary 217 D default — The setting selected by a program when the user does not specify an alternati ve setting. device — A component attached to the computer . Devices may be external (outside the computer’ s case) or internal (inside the computer’ s case). Printers, disk dr iv es, and modems are examples of devices. device driv er — A[...]

218 Glossary double-click — T o press and release the pointing device’ s primary button rapidly twice without moving the pointing device. In the W indows ® operating system, this refers to the pointing de vice’ s left button, unless otherwise stated. double-density d iskette — A 3.5-inch diskette that can hold up to 720 KB of information ([...]

Glossary 219 F fil e — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also docum ent. f ile allocation table (F A T) — T h e s e c t i o n of a n internal storage driv e that keeps track of the location of s tored files. fil e n a m e — A set of[...]

220 Glossary Hibernation — A feature of many T oshiba computers that sav es to the i n t e r n a l s t o r a g e d r iv e the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned of f. See [...]

Glossary 221 liquid crystal di splay (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it. A filter o ver the electrodes permits only non-polarized l[...]

222 Glossary N network — A collection of computers a nd associated de vices that are connected by communications facilities. A network allows you to share data and peripheral de vices, su ch as printers, with other users and to exchange electronic mail. non-interlaced — A method of refreshing a computer scr een, in which each pixel of e very li[...]

Glossary 223 Plug and Play — Generally , refers to the com puter’ s ability to automatically configure itself to work with per ipheral devices. When capitalized, refers to a sta ndard that, when followed by a device manufacturer , allo ws a computer to conf igure itself automatically to work with the device. pointing de vice — Any de vice, su[...]

224 Glossary RJ11 — A modular connector used o n most U.S. telephone systems and direct-connect modems. The RJ11 co nnector is a 6-wire connector . R OM (read-only memory) — Non-v olatile memory that can be read but not written to. Non-volatile here means that information in ROM remains whether or not the computer is recei ving power . This typ[...]

Glossary 225 T TFT display — See active-ma trix display . U universal serial bus (USB) — USB is a serial b us that supports a data transfer rate of up to 480 Mbps (480 million bits per second). USB can connect up to 127 peripheral de vices through a single all- purpose USB port. USB allows hot swapping of peripherals. See also bus, hot swapping[...]

226 Index A A C adaptor 46 AC p o w e r connecting adaptor 47 accessories memory 51 adding memory 51 Alt keys 89 Application Cards 198 audio fil e s 129 audio features 129 B backing up files 87 battery changing 113 charge indicator light 48 , 107 charge not lasting 174 charging 46 , 48 conserving po wer 110 disposal 117 low char ge 109 monitoring p[...]

227 Index moving 84 non-system disk or disk error message 167 not accessing disk driv es 166 running on battery power 103 setting up 43 , 53 warning resume failure messag e 166 computer lock 85 computing tips 86 ConfigFree® 160 connecting 69 connecting to a power source 46 connection set up 124 control buttons 68 Ctrl keys 89 D desktop creating ne[...]

228 Index external diskette driv e connecting 73 external display , adj usting 71 F F A T (File Allocation T able) 177 file e xtensions 95 file, backing up 87 fil e s backing up 96 printing 95 restoring 96 saving 93 fi ngerprint authentication 157 fingerprint Authentication Utility using 157 FM tuner 130 Fn keys 89 function keys 89 H hard driv e re[...]

229 Index troubleshooting 174 using 88 keyboard, e xternal 71 keyboard, full-size 88 L lock computer , using 85 M main battery removing 113 memory adding 51 problem solving 172 remo ving memory module slot cov er 54 memory module inserting 55 installation 52 removing 58 memory module slot 54 microphone 129 modem connecting to telephone line 124 pro[...]

230 Index using Shut Dow n 76 using Sleep 81 precautions 41 primary button 68 printer connecting 71 problem solving 182 , 18 3 printing a file 95 problem solving AC p o w e r 173 accessing disk dri ves 166 battery charge does not last 174 battery not charging 173 cannot insert diskette in drive 178 cannot read a diskette 178 changing display proper[...]

231 Index precautions 41 saving f iles 93 screen blank 175 does not look norm al/flickers 176 secondary button 68 set up communications 123 setting up adding memory 51 computer 43 , 53 work en vironment 40 setting up a connection 124 Sleep mode 75 hot key 203 starting again from 83 sound problem solving 180 sounds recording 129 speakers using exter[...]

232 Index W indo ws® Start menu 91 wireless netw orking 123 W izards Connect to the Internet 124 W orld W ide W eb 126 www 126[...]