Zenoah G2500TS manuel d'utilisation

Aller à la page of 36

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Zenoah G2500TS. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Zenoah G2500TS ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Zenoah G2500TS décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Zenoah G2500TS devrait contenir:
- informations sur les caractéristiques techniques du dispositif Zenoah G2500TS
- nom du fabricant et année de fabrication Zenoah G2500TS
- instructions d'utilisation, de réglage et d’entretien de l'équipement Zenoah G2500TS
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Zenoah G2500TS ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Zenoah G2500TS et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Zenoah en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Zenoah G2500TS, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Zenoah G2500TS, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Zenoah G2500TS. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    OWNER / OPERA T OR MANUAL CHAINSA WS T2040-93110(010)  The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING APPLICABLE SERIAL NUMB[...]

  • Page 2

    [...]

  • Page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i[...]

  • Page 4

    2. Specifications ■ G2500TS Power unit : Dis placement ····················································································· 1.6(25.4) cu-in(cm 3 ) Fuel ···············································[...]

  • Page 5

    3. Symbols on the machine ❲ 5 ❳ Made in Japan RedMax IMPORT ANT ENGINE INFORMA TION THIS ENGINE CONFORMS T O US EP A PH1 FOR SMALL OFF-RO AD ENGINES. ENGINE F AMIL Y : YKZXS.0254DE:EM ENGINE DISPLACEMENT : 25.4cc REFER TO O WNER'S MANUMAL FOR MAINTE- NANCE SPECIFICA TIONS AND ADJUSTMENTS. MANUF ACTURED : INFORMA TION IMPORT ANTE CONCERNANT[...]

  • Page 6

    ❲ 6 ❳ 4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices. 3. Always use caution when handling fuel.[...]

  • Page 7

    ❲ 7 ❳ 4. For safe operation 1 6 . Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 1 7 . Do not operate a chain saw in a tree unless specially trained to do so. 18. Guard against kickback. Kickback is the upward motion of the gui[...]

  • Page 8

    A standard saw unit package contains the items as shown below. (SE1) (1) Power unit (2) Guide bar (3) Saw chain (4) Plug wrench Open the box and install the guide bar and the saw chain on the power unit as follows. The saw chain has very sharp edges. Use protective gloves for safety. 1. Pull the guard towards the front handle to check that the chai[...]

  • Page 9

    5. Installing guide bar and saw chain ❲ 9 ❳ SE5 SE6 6 . While holding up the tip of the bar,adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. (SE5) (1) Chain tension adjusting screw (a) Loosen (b) Tighten 7. Tighten the mounting nut securely with the bar tip held up (TORQUE:[...]

  • Page 10

    ❲ 10 ❳ 6. Fuel and chain oil ■ FUEL The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti- oxidant added quality oil expressly labeled for air- cooled 2-cycle engine use. RECOMMENDED MIXING RATIO GASOLINE 32 : OIL 1 Exhaust emission are controlled [...]

  • Page 11

    6. Fuel and Chain oil ■ CHAIN OIL Use motor oil SAE 10W-30 all year round, or SAE 30-40 in summer and SAE 20 in winter. Do not use waste or regenerated oil that can cause damage to the oil pump. NOTE ❲ 11 ❳[...]

  • Page 12

    ❲ 12 ❳ ■ STARTING ENGINE 1 . Feed fuel and chain oil into their respective tanks and tighten the caps securely. (OP1) (1) Fuel (2) Chain oil 2 . Continuously push the priming bulb until fuel comes in the bulb. (OP2) 3. Put the switch to the "I" position. (OP3) (1) Switch 4 . Pull out the choke knob to the second-stage position. The [...]

  • Page 13

    OP8 7. Operation Once the choke knob has been pulled out, it will not return to the operating position even if you press down on it with your finger. When you wish to return the choke knob to the operating position, pull out the throttle lever instead. 5 . While holding the saw unit securely on the ground, pull the starter rope vigorousl y. (OP6) 6[...]

  • Page 14

    ❲ 14 ❳ ■ ADJUSTING CARBURETOR (OP9) The carburetor on your unit has been factory adjusted, but may require fine tuning due to change in operating conditions. Before adjusting the carburetor, make sure that provided are clean air/fuel filters and fresh, properly mixed fuel. When adjusting, take the following steps: Be sure to adjust the carbur[...]

  • Page 15

    ❲ 15 ❳ 7. Operation OP10 OP11 • When the brake operates, release the throttle lever to slow down the engine speed. Continuous operation with the brake engaged will generate heat from the clutch and may cause trouble. • At machine inspection prior to each job, check the operating condition of the brake following the steps below. 1. Start the[...]

  • Page 16

    ❲ 16 ❳ 8. Sawing SA1 • Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • Always follow the safety regulations. The chain saw must only be used for cutting wood. It is forbidden to cut other types of material. Vib[...]

  • Page 17

    SA3 ■ FELLING A TREE (SA2) When you fell a tree, be sure to warn your neighboring workers of the danger. 1. Decide the felling direction considering the wind, Iean of the tree, location of heavy branches, ease of job after felling, and other factors . 2. While clearing the area around the tree, arrange a good foothold and retreat path. 3. Make a [...]

  • Page 18

    ❲ 18 ❳ ● Cutting a pillowed log In the area A in the picture right above, saw up from the bottom one-third and finish by sawing down from the top. In the area B, saw down from the top one-third and finish by sawing up from the bottom. (SA4) ● Limbing a felled tree Be alert to the spring back of a cut limb. First check which way the limb is [...]

  • Page 19

    9. Maintenance Make sure the engine is stopped . ■ DAILY CHECK POINTS 1. Air filter Loosen the knob and remove the air cleaner cover. Take off the filter elements and tap off attached sawdust. When they are extremely dirty, shakewash with gasoline. Dry them completely before reinstalling. (MA1) 2. Oiling port Dismount the guide bar and check the [...]

  • Page 20

    ❲ 20 ❳ 9. Maintenance This saw is equipped with one of the following low kickback bar/chain combinations: RedMax Part Number Bar Size Guide Bar Saw Chain 12inch (30cm) G2512 91VG45X For replacement, use only above bar and chain, or the following; OREGON BAR 12 inch S/N DOUBLE GUARD BAR, Mount code #A041. (120 SDEA 041) GB BAR 12 inch MINI LAMIN[...]

  • Page 21

    When returning the filter, use a pinch not to be folded the suction pipe. 4. Spark plug Clean the electrodes with a wire brush and adjust the gap to 0.6mm. (MA8) Replacement plug: Champion RCJ-7Y After spark plug maintenance, reinstall the plug and plug cap firmly. (TORQUE: 14.7~17.6 N.m./150~180 kg-cm) Or it may cause the fire accident. (MA9) (1) [...]

  • Page 22

    ❲ 22 ❳ 9. Maintenance 7. Saw Chain It is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. • The cut way does not go straight. • Vibration increases. • Fuel consumption increases. Cutter setting standar[...]

  • Page 23

    9. Maintenance Make sure every cutter has the same length and edge angles as illustrated. (MA14) (4) Cutter length (5) Filing angle (6) Side plate angle (7) Top plate cutting angle 8. Way of the cooling air • The engine metal parts can burn your skin. Never touch the cylinder, muffler or ignition plug etc. during operation or right after stopping[...]

  • Page 24

    ❲ 24 ❳ 9. Maintenance 9. Muffler (MA16) If you do not attach the muffler correctly, after engine starts, the muffler will be loosen and the hightemperature exhaust gas spout. After cleaning the muffler, pay attention to fit up the muffler according to the explanation as follows. 1 . Muffler body, muffler cover and baffle will be combined correc[...]

  • Page 25

    ❲ 25 ❳ 10. Storage 1. Empty the fuel tank and run the engine out of fuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place out of the reach of children.[...]

  • Page 26

    ❲ 26 ❳ 1 1. T roubleshooting Guide Case 1. Starting failure: Make sure the icing prevention system is not working. Case 2. Lack of power/Poor acceleration/Rough idling Case 3. Oil does not come out Check fuel for water or substandard mixture. Check for engine flooding. Check the spark. Check fuel for water or substandard mixture. Check air filt[...]

  • Page 27

    ❲ 27 ❳ 12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model [...]

  • Page 28

    ❲ 28 ❳ 12. Parts list Fig.1 POWER UNIT G2500TS (S/N 010101 and up) G2500TS[...]

  • Page 29

    ❲ 29 ❳ Fig.1 POWER UNIT (S/N 010101 and up) G2500TS 1 2841-12101 CYLINDER COMP 1 2 2841-12120 • ELBOW 1 3 2841-12210 PIPE 1 4 3310-82230 CLIP 1 5 3350-34320 ELBOW 1 6 2841-21110 CRANKCASE 1 7 01252-30520 BOLT, hexagon hole 4 M5x20 8 2841-41112 PISTON 1 9 2841-41210 RING, piston 1 10 1600-41310 PIN 1 11 1260-41320 RING, snap 2 12 1140-41330 BE[...]

  • Page 30

    ❲ 30 ❳ 12. Parts list Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 010101 and up) G2500TS[...]

  • Page 31

    ❲ 31 ❳ Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 010101 and up) G2500TS Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 T2040-81000 CARBURETOR ASS'Y 2 2630-81120 • PUMP COVER 1 3 3310-81130 • SCREW 1 4 3310-81280 • COVER 1 5 1480-81420 • PLUG 1 6 3350-81380 • SPRING 1 7 2630-81330 • SCREW 1 8 2880-81470 • SCREW [...]

  • Page 32

    THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S STRINGENT ANTI-SMOG STANDARDS. KOMATSU ZENOAH Co[...]

  • Page 33

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL G2500TS UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED[...]

  • Page 34

    © Printed in Japan Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de [...]

  • Page 35

    [...]

  • Page 36

    KOMA TSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093  © Printed in Japan[...]