Acer P1166P manuale d’uso

SER VICE MANUAL SI : TSE: Check: Approved: Date Revise V ersion Description 2008.07.29 V1.0 Initial Issue 2009.01. 23 V2.0 Add P1266i, P1 166P , P1266P P1 166 / P1266 / P1266i / P1 166P / P1266P Copyright January , 2009. All Rights Reserved P/N: 36.8BE04G001[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential I P1 166 / P1266 / P1266i / P1 166P / P1266P Comparison List Comparison List P ARTS P1 166 P1266 P1 166P P1266P P1266I THERMAL SWITCH 43.8BB01G001 43.89J02G001 LAMP DRIVER 75.8BA01G001 75.8BJ10G001 LAMP MODULE SP .8BE01GC01 SP .8BA01GC01 LAMP COVER 51.8BA06G002 70.8BA24GR01 DMD 48.87K01G001 4[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential II Preface This manual is applied to P1 166 / P1266 / P1266i / P1 166P / P1266P projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product. Y our customers will appreciate the quick response time when you immediately [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential III T able of Content Chapter 1 Introduction Highlight 1-1 Compatible Mode 1-4 Product Overview 1-6 Chapter 2 Disassembly Process Equipment Needed & Product Overview 2-1 Disassemble Lamp Cover Module and Lamp Module 2-2 Disassemble T op Cover Module 2-3 Disassemble Keypad Module 2-3 Disas[...]

Condential P1 166 / P1266 / P1266i / P1 166P / P1266P IV Disassemble Elevator Module 2-18 Rod Adjustment 2-19 Re-write Lamp Usage Hour 2-20 Assemble Elevator Module 2-21 Assemble Bottom Support Module 2-22 Assemble Speaker Module 2-23 Assemble L VPS Module 2-24 Assemble Interrupt Switch Module 2-25 Assemble Lamp Driver Module 2-25 Assemble DMD B[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential V Chapter 4 Function T est & Alignment Procedure T est Equipment Needed 4-1 Service Mode 4-1 OSD Reset 4-1 T est Condition 4-2 T est Inspection Procedure 4-3 PC Mode 4-3 PC Calibration 4-7    Defectspecicationtable     4[...]

Condential P1 166 / P1266 / P1266i / P1 166P / P1266P VI EDID Key-In Procedure 6-4 Setup Procedure (HDMI) 6-6 Default Language Reset 6-9 Appendix A Exploded Image I Appendix B    SerialNumberSystemDenition     I   PCBA[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P  1-16 Chapter 1 Introduction 1-1 Highlight No   1         [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P   No             ?[...]

  P1 166 / P1266 / P1266i / P1 166P / P1266P No             ?[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P   1-2 Compatible Mode Computer Compatibility (Analog)           [...]

  P1 166 / P1266 / P1266i / P1 166P / P1266P             ?[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P  1-21 Product Overview Projector Outlook Front /Upper side     1    2  6 [...]

 1-22 P1 166 / P1266 / P1266i / P1 166P / P1266P Rear side     1    2   ?[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P  1-23 Control Panel    1   2      [...]

 1-24 P1 166 / P1266 / P1266i / P1 166P / P1266P Remote Control Layout[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P       1     2  ?[...]

 1-26 P1 166 / P1266 / P1266i / P1 166P / P1266P        [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P   Note: “*” Only for P1266i series, “#” Japan area is not supported.[...]

  P1 166 / P1266 / P1266i / P1 166P / P1266P Connecting the Projector     1  6  2    ?[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P     1  2  3  4  Note: For P1266i only Connecting the Projector for Wireless Function[...]

  P1 166 / P1266 / P1266i / P1 166P / P1266P System Block Diagram[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P  1-31 Bottom Cover Dimension[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 2-1 Chapter 2 Disassembly& Assembly Process 2-1 Equipment Needed & Product Overview 1. Screw Bit (+) :107 2. Hex Sleeves 5mm 3. Hex Sleeves 8mm 4. T weezers 5. Long Nose Nipper , Angle Cutting Nipper 6. Sider Cutter Pliers 7. Projector * Before you start: This process is protective le[...]

Condential 2-2 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-2 Disassemble Lamp Cover Module and Lamp Module 1. Unscrew 2 screws (as red circle) to disassemble Lamp Cover Module. 2. Unscrew 2 screws (as yellow circle) to disassemble Lamp Module. Lamp Module[...]

Condential 2-3 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-3 Disassemble T op Cover Module 1. Unscrew 2 screws (as red circle) on Back Cover . 2. T urn the projector to backside. Unplug 1 connector (as red square) Note: - Pull up the T op Cover slowly to protect the connec tor from damage. 3. Disassembled T op Cover Module. 2-4 Disassemble Keyp[...]

Condential 2-4 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-5 Disassemble Zoom Ring 1. Unscrew 3 screws (as red circle). 2. Use a tweezer to remove 2 tenons (as yellow circle) and then take off Zoom Ring. 2-6 Disassemble T op Shielding 1. Unscrew 1 1 screws (as red circle). 2. Disassemble T op Shielding.[...]

Condential 2-5 P1 166 / P1266 / P1266i / P1 166P / P1266P 4. Press Bottom Support shielding as blue arrow directs, push Main Board Module as red arrow directs. Note: - When pulling up the Main Board, please handle it carefully to avoid damaging the connector that connects the DMD Board (as red square). 2-7 Disassemble Main Board Module 1. Unscre[...]

Condential 2-6 P1 166 / P1266 / P1266i / P1 166P / P1266P 5. Unplug 1 connector (as red square). Note: The connector is under Main Board. 6. Disassemble Main Board Module. 7. T ear Mylar off the Main Board. 2-8 Disassemble Wireless Module (only for P1266i) 1. T urn back the Main Board. 2. Unscrew 3 screws (as red circle) to disassemble Wireless [...]

Condential 2-7 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-10 Disassemble Front Cover Module 1. Press 5 tenons (as red circle) to disassemble Front Cover . 2-9 Disassemble Back Cover 1. Pull up Back Cover in the direction of the red arrow . A B B A[...]

Condential 2-8 P1 166 / P1266 / P1266i / P1 166P / P1266P 2. Press 2 tenons (as yellow circle) to disassemble IR sensor . 2-1 1 Disassemble Fan Module 1. Unscrew 4 screws (as red circle) to disassemble Fan Module. 2. Unplug 1 connector (as yellow square) to disassemble Fan. A A[...]

Condential 2-9 P1 166 / P1266 / P1266i / P1 166P / P1266P 3. Unscrew 4 screws (as yellow circle) to disassemble Fan&Bracket. 4. T ake off Lamp Blower Rubber (as blue square).[...]

Condential 2-10 P1 166 / P1266 / P1266i / P1 166P / P1266P 5. Unscrew 1 screw (as blue circle) to disassemble Thermal Switch. Thermal Switch 2-12 Disassemble Blower Module 1. Unscrew 3 screws (as red circle) to disassemble Blower Module. 2. Disassemble Blower and Blower Bracket.[...]

Condential 2-1 1 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-13 Disassemble Engine Module, Color Wheel Mo du le a nd R od M od ul e 1. Unscrew 4 screws (as red circle) to disassemble Engine Module. 2. Unscrew 2 screws (as yellow circle) to disassemble Color Wheel Module.[...]

Condential 2-12 P1 166 / P1266 / P1266i / P1 166P / P1266P 4. Unscrew 3 screws (as red circle). 5. Disassemble ROD Fix Plate and ROD Module. 6. Disassemble Focus Ring. Note: - Pay attention to the three tenons when disassembling focus ring. 3. Unscrew 1 screw (as green circle) to disassemble Photo Sensor from Color Wheel Module.[...]

Condential 2-13 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-14 Disassemble DMD Board and DMD Chip Module 1. Unscrew 2 hex screws (as red circle). 2. Disassemble DMD Board and DMD Chip Module. 3. Rotate the switch(as blue square) and then take off DMD Chip.[...]

Condential 2-14 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-15 Disassemble Lamp Driver Module 1. Unscrew 1 screw (as red circle) to disassemble Lamp Driver Module. Note: - Pull up lamp driver module from the bottom support shielding (as red square). 2. Pull up 1 connector (as red square) to disassemble Lamp Driver Module.[...]

Condential 2-15 P1 166 / P1266 / P1266i / P1 166P / P1266P 3. Unscrew 2 screws(as red circle). 4. Unscrew 1 screw(as yellow circle). 5. Unplug 3 connectors (as green square). 5. Disassemble Lamp Driver from Lamp Driver Support Shielding. 6. T ake off lamp cables. 2-16 Disassemble Interrupt Switch Module 1. Unplug 1 connector (as yellow square) f[...]

Condential 2-16 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-17 Disassemble L VPS Module 1. Unscrew 3 screws (as red circle) to take off AC Inlet Bracket. 2. Unscrew 1 ground screw (as yellow cirle). 3. Unscrew 3 screws (as blue circle) to disassemble L VPS Bracket & Mylar . A A[...]

Condential 2-17 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-18 Disassemble Speaker Module 1. Unscrew 1 screw (as red circle) to disassemble speaker module. 2. Press 2 tenons (as yellow circle) to disassemble Speaker and Speaker Holder . A[...]

Condential 2-18 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-19 Disassemble Bottom Support Module 1. Unscrew 1 screw (as red circle) to disassemble Bottom Support Module. 2-20 Disassemble Elevator Module 1. Disassemble the Ru bber (as red square). 2. Disa ssemble 1 Sprin g (as y ellow s quare).[...]

Condential 2-19 P1 166 / P1266 / P1266i / P1 166P / P1266P 3. Press 2 tenons (as green square) to disassemble Elevator Holder . 4. Unscrew 2 screws (as red circle), then press 1 tenon (as blue square) to disassemble Elevator Foot. 2-21 Rod Adjustment 1. Environment adjustment - The distance between the engine and the screen is 2.37M - This proce[...]

Condential 2-20 P1 166 / P1266 / P1266i / P1 166P / P1266P (“screw 1“ should be asjusted rst, and then “screw 2“. Adjust until the yellowish or bluish parts disappeared.) 3. Abnormal image inspection - It should not have any abnormal color at the rim of the image by estimating through the eyes. Note: - T o avoid over adjusting the rod[...]

Condential 2-21 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-23 Assemble Elevator Module 1. Fasten 1 tenon (as blue square) to assemble ElevatorRoot. Then screw 2 screws (as red circle). 2.Fasten 2 tenons (as green square) to assemble Elevator Holder . 3. Assemble 1 Spring (as yellow square). T est”. 4. Choose “Return to Service Menu”. 5. [...]

Condential 2-22 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-24 Assemble Bottom Support Module 1. Screw 1 screw (as red circle) to assemble Bottom Support Module. 4. Assemble the Rubber (as red square).[...]

Condential 2-23 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-25 Assemble Speaker Module 1. Fasten 2 tenons (as yellow circle) to assemble Speaker and Speaker Holder . 2. Screw 1 screw (as red circle) to assemble Speaker Module. .[...]

Condential 2-24 P1 166 / P1266 / P1266i / P1 166P / P1266P A 2-26 Assemble L VPS Module 1. Screw 3 screws (as blue circle) to assemble L VPS Bracket & Mylar . 2. Screw 1 ground screw (as yellow cirle). 3. Screw 3 screws (as red circle) to x AC Inlet Bracket. A A[...]

Condential 2-25 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-27 Assemble Interrupt Switch Module 1. Fasten 2 tenons (as yellow circle) to assemble Interrupt Switch Module. 2. Plug 1 connector (as yellow square) into L VPS. A A B B 2-28 Assemble Lamp Driver Module 1. Aassemble Lamp Driver with Lamp Driver Support Shielding. 2. Connect Lamp Cables[...]

Condential 2-26 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-29 Assemble DMD Board and DMD Chip Module 1. Rotate the switch (as blue square) to assemble DMD Chip. 5. Plug 1 connector (as red square) to assemble Lamp Driver Module. 6. Screw 1 screw (as red circle) to assemble Lamp Driver Module. Note: - Put lamp driver module below the bottom sup[...]

Condential 2-27 P1 166 / P1266 / P1266i / P1 166P / P1266P 2. Assemble DMD Board and DMD Chip Module. 3. Screw 2 hex screws (as red circle). 2-30 AssembleEngine Module, Color Wheel Mod ule a nd Ro d M odu le 1. Assemble Focus Ring. Note: - Pay attention to the three tenons when disassembling focus ring. 2. Screw 3 screws (as red circle)to assemb[...]

Condential 2-28 P1 166 / P1266 / P1266i / P1 166P / P1266P 4. Screw 2 screws (as yellow circle) to Screw 2 screws (as yellow circle) to assemble Color Wheel Module. 5. Screw 4 screws (as red circle) to assemble Engine Module.[...]

Condential 2-29 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-31 Assemble Blower Module 1. Assemble Blower and Blower Bracket. 2. Screw 3 screws (as red circle) to assemble Blower Module. 2-32 Assemble Fan Module 1. Screw 1 screw (as blue circle) to assemble Thermal Switch.[...]

Condential 2-30 P1 166 / P1266 / P1266i / P1 166P / P1266P 3. Screw 4 screws (as yellow circle) to assemble Fan&Bracket. 2. Assemble Lamp Blower Rubber (as blue square).[...]

Condential 2-31 P1 166 / P1266 / P1266i / P1 166P / P1266P A A 4. Plug 1 connector (as yellow square) to assemble Fan. 5. Screw 4 screws (as red circle) to assemble Fan Module. 2-33 Assemble Front Cover Module 1. Fasten 2 tenons (as yellow circle) to assemble IR sensor .[...]

Condential 2-32 P1 166 / P1266 / P1266i / P1 166P / P1266P A B B A 2-34 Assemble Back Cover 1. Assemble Back Cover in the direction of the red arrow . 2. Fasten 5 tenons (as red circle) to assemble Front Cover .[...]

Condential 2-33 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-36 Assemble Main Board Module 2. Assemble mylar on the Main Board. 3. Connect 1 connector (as red square). Note: The connector is under Main Board. 2-35 Assemble Wireless Mod ule ( onl y f or P1 266i ) 1. Screw 3 screws (as red circle) to disassemble Wireless Module. 2. T urn back the [...]

Condential 2-34 P1 166 / P1266 / P1266i / P1 166P / P1266P 5. Plug 7 connecors (as yellow square). 6. Screw 3 screws (as blue circle). 7. Screw 4 hex screws (as red circle). 4. Press bottom support shielding as blue arrow directs, push Main Board Module as red arrow directs. Note: The connector on the Main Board should be connected to the DMD Bo[...]

Condential 2-35 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-37 Assemble T op Shielding 1. Assemble T op Shielding. 2. Screw 1 1 screws (as red circle) on T op Shielding. 2-38 Assemble Zoom Ring 1. Fasten 2 tenons (as yellow circle) to assemble Zoom Ring. 2. Screw 3 screws (as red circle).[...]

Condential 2-36 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-39 Assemble Keypad Module 1. Assemble Keypad Board,Keypad Board Bracket and Mylar . 2. Plug 1 FPC Cable (as yellow square). 3. Screw 4 screws (as red circle). 2-40 Assemble T op Cover Module 1. Assemble the T op Cover Module. 2. Unplug 1 connector (as red square). 3. T urn the projecto[...]

Condential 2-37 P1 166 / P1266 / P1266i / P1 166P / P1266P 2-41 Assemble Lamp Cover Module and Lamp Module 1. Screw 2 screws (as yellow circle) to assemble Lamp Module. 2. Screw 2 screws (as red circle) to assemble Lamp Cover Module.[...]

3-1 Condential P1 166 / P1266 / P1266i / P1 166P / P1266P Chapter 3 T roubleshooting 3-1 LED Lighting Message NO. Message Lamp LED T emp LED Power LED Red Red Red Blue 1 Standby (power cord plugged in) -- -- V -- 3 Power button ON -- -- -- V 4 Lamp retry -- -- -- Quick ashing 5 T urning off (cooling state) -- -- Quick ashing -- 6 T urning [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 3-2 3-2 Beep Sound Power on (as soon as power button pressed) So (0.3s) Power on (lamp lighting failed) 2 x {So(0.1s) – Off(0.1s)} per lighting failure 12s interval for each trial lighting. Max 4 times of trial Power on (lens cap was not opened, for the model with sliding lens cover only) 2[...]

3-3 Condential P1 166 / P1266 / P1266i / P1 166P / P1266P 3-3 Main Procedure No Symptom Procedure 1 No Power - Ensure the Power Cord and AC Power Outlet are securely connected - Check Lamp Cover and Interrupt Switch - Ensure all connectors are securely connected and aren’t broken - Check Lamp driver - Check L VPS - Check Main Board 2 Auto Shut[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 3-4 No Symptom Procedure 5 Mechanical Noise - Check Color Wheel - Check Fan Module 6 Line Bar / Line Defect - Sometimes it’s because of the DMD Chip and the DMD Board did not assemble properly - Check DMD Board - Check DMD Chip - Check Main Board 7 Image Flicker - Do “Reset” of the OSD [...]

3-5 Condential P1 166 / P1266 / P1266i / P1 166P / P1266P No Symptom Procedure 12 Remote Control / Control Panel Failed - Remote Control a. Check Battery b. Check Remote Control c. IR Receiver - Control Panel a. Check FPC b. Check Keypad c. Check Main Board 13 Function Abnormal - Do “Reset” of the OSD Menu - Check Main Board - Check DMD Boar[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 3-6 No Symptom Procedure 15 Forgetting Pass - word (adminstra - tor Password) - An unique Universal Password which is printed on the Security Card. This unique password is a back door of Administrator Password which will be accepted by projec- tor anytime no matter what the Administrator Pass[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 4-1 Chapter 4 Function T est & Alignment Procedure 4-1 T est Equipment Needed - IBM PC with XGA resolution and Wireless Network Card - DVD player with Multi-system (NTSC/P AL/SECAM), equipped “Component”, “S-Video” , “Composite” and "HDMI". - HDTV Source (480P , 720P[...]

Condential 4-2 P1 166 / P1266 / P1266i / P1 166P / P1266P 4-4 T est Condition - Circumstance brightness: Dark room less than 5.0 lux. - Inspection distance: 1.8 M~2.5 M functional inspection. - Screen size: 60 inches diagonal - After repairing each P1 166 / P1266 / P1266i / P1 166P / P1266P , the unit should be run-in (refer to the table below) [...]

Condential 4-3 P1 166 / P1266 / P1266i / P1 166P / P1266P 4-5 T est Inspection Procedure Charge parts Update Main Board Firmware Color Wheel Lamp Module EDID Lamp Driver V ersion Update v v v Color Wheel Index v v Reset lamp hour v OSD Reset v v EDID v Re-write Lamp Hour Usage v Default Language Reset v v v W aveform Download v 4-6 PC MODE Note:[...]

Condential 4-4 P1 166 / P1266 / P1266i / P1 166P / P1266P total pixel number of pixel clock in one line period. (2) Select "T racking" function and use right or left arrow key to adjust the value to minimize video icker . - Adjust Resync or Frequency/T racking/H. Posi - tion/V . Position to the inner screen. Inspection item - Elimin[...]

Condential 4-5 P1 166 / P1266 / P1266i / P1 166P / P1266P 3. Blemish (Dark) Procedure - T est equipment: video generator . - T est signal: analog 1024 x 768@60Hz. 1024 x 768@60Hz. . - T est Pattern: blue 60 Inspection item - Dark blemish check. (dirty) Criteria - It is acceptable to have four dark blemish at dark blemish at most on blue 60 patte[...]

Condential 4-6 P1 166 / P1266 / P1266i / P1 166P / P1266P 6. Focus test Procedure - T est equipment: video generator . - T est signal: analog 1024 x 768@60Hz 1024 x 768@60Hz - T est Pattern: full screen or MEME Sony Inspection item - Focus check Criteria - From screen 1.95 M via visual to check the focus, look at the entire screen, focus shall b[...]

Condential 4-7 P1 166 / P1266 / P1266i / P1 166P / P1266P (the unidentied color levels on both left and right sides should not over 8 color levels.) - Gray level should not have abnormal color or heavy lines. - The PC mode functionally sure be workable include support format with frequency and auto detected functional will be workable 4-7 PC [...]

Condential 4-8 P1 166 / P1266 / P1266i / P1 166P / P1266P 4-8 Defect specication table Order Symptom Pattern Criteria 1 Bright pixel ( dots) Black pattern ( IRE=O) A+B=0 2 Dark pixel(dots) White pattern A+B=6 3 Unstable pixel (dots) Any pattern A+B=1 4 Adjacent dark pixel (dots) Any pattern A+B=0 5 Dark blemish (Dirty) Blue 60 pattern A+B=4 ([...]

Condential 4-9 P1 166 / P1266 / P1266i / P1 166P / P1266P 2. S-Video Procedure - T est equipment: DVD player - Test signal: S-Video Inspection item - Video performance test Inspection Distance - 1.8 M ~2.5 M Criteria - Check any abnormal color , line distortion or any noise on the screen. - Check the sound from speakers. 3. HDTV/ Component Proce[...]

Condential 4-10 P1 166 / P1266 / P1266i / P1 166P / P1266P 4-10 Optical Performance Measure Inspection Condition - Environment luminance: 5 Lux - Product must be warmed up for 3 minutes - Distances from the screen: 1.95 M - Screen Size: 60 inches diagonal 1. T est equipment Procedure - Get into service mode: Press "Power→Left→ Left→Me[...]

Condential 4-1 1 P1 166 / P1266 / P1266i / P1 166P / P1266P Note: P5=center of white image B5=center of black image. Criteria  1400: 1 (for P1 166 / P1266)  1400: 1 (for P1 166 / P1266) 1400: 1 (for P1 166 / P1266) (for P1 166 / P1266) 1900: 1 (for P1266i / P1 166P / P1266P) 4. Uniformity Procedure - Full white pattern - Use CL100 to measu[...]

Condential 4-12 P1 166 / P1266 / P1266i / P1 166P / P1266P Acoustic - High pitch sound from cooling fan and color wheel is unacceptable. 2. Check points for exterior and print pattern Check item Check point T ext & Pattern Missing letters & pattern or blurry prints are unacceptable Exterior Dirt, scrape, water ripples and uneven color ar[...]

Condential 4-13 P1 166 / P1266 / P1266i / P1 166P / P1266P 4-12 LAN and Wireless Function T est (only for P1266i) 1. Write down Projector ID and Server IP - Plug in power cord to the projector and connect PC with projector by RJ45 cable. - T urn on the projector . - Write down the Projector ID: "8948" and Server IP address: 192.168.100[...]

Condential 4-14 P1 166 / P1266 / P1266i / P1 166P / P1266P - Modify the IP address to 192.168.100.12, and modify Subnet mask to 255.255.255.0. Note: The HOST ID (192.168.100. XXX ) of PC IP address must be different from the Server IP address written down in step 1. - Click "OK". - Click "Close" to quit the setting screen. 3.[...]

Condential 4-15 P1 166 / P1266 / P1266i / P1 166P / P1266P 4. Acer Projector Gateway Installation - Double click "Acer .exe" le. - Click "Next". - "Empowering T echnology - Acer eProjection Management" and "Login - AcerProjectorGateway" will appear on the sreen, the Installation complete. 5. LAN Functio[...]

Condential 4-16 P1 166 / P1266 / P1266i / P1 166P / P1266P 5. Wireless Network Function T est - Unplug LAN Cable from Projector and PC. - Right click "Wireless Network Connection", then choose "View Available Wireless Networks". - "Wireless Network Connection" picture will appear on the screen, then double click &qu[...]

Condential 5-1 P1 166 / P1266 / P1266i / P1 166P / P1266P Chapter 5 Firmware Upgrade 5-1 Equipment Needed Software : (DDP 2230- USB) - DLP Composer - Firmware - 8M Flash (8M ash has to put in PC and set right path in 5-4 step 5) Note: Befrore rmware upgrade, extract 8M ash le to DLP composer iles .( according to 5-4 step 1) Hardwa[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 5-2 5-2 DLP Composer Lite Setup Procedure 1. Choose "DLP Composer Lite V7.1 Setup" Program. 2. Click "Next". 3. Read License Agreement. - Choose I accept and agree to be bound by all the terms and conditions of this License Agreement. 4. Click "Next". 5. Click &q[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 5-3 6. Click Next. 7. Click Next. 8. Writing system registry values. 9. Click Finish.[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 5-4 5-3 USB Driver Upgrade Procedure 1. set up - Plug in Power cord to projector . - Link PC USB port and projector USB port by USB Cable. 2. Execute Program (1) Found new hardware wiszard will be appearred on the screen. (2) Select Install the software automatically (Recommended). (3) Then c[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 5-5 5-4 Firmware Upgrade Procedure 1. Unzip "8M ash.rar" to "DLP Composer Lite v7.1 Setp" les. 2. Set-up - Hold on "Power" button and plug in power cord while holding on "Power". - Once the Lamp LED and the T emp LED light on Red, plug in USB cabl[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 5-6 6. Select EditpreferencesCommunications - Choose USB". - Click OK". 7. Choose Flash Loader . - Select the item "Skip Boot Loader Area" (select 32KB) - Click "Browse" to search the rmware le. - Select the FW le (*.img). - Click "Open".[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 5-7 8. Click "Reset Bus" to erase the ash memory . 9. If the  rmware i s ready , click start downlo ad to process the rmware upgrade. - Click "Y es" to erase the ash memory . 10. When rmware upgrade process is nished, the unit return to stand-by status. T[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 5-8 T emp LED Lamp LED Power LED Up Button 5-5 W aveform Download 1.Hold on the “up” button, then plug power cord in, the Power LED light on red,after about 5 seconds, it turns to blue and T emp LED will ash for 4 seconds. After that, the T emp LED and Lamp LED light on red, and Power [...]

Condential 6-1 P1 166 / P1266 / P1266i / P1 166P / P1266P Chapter 6 EDID Upgrade 6-1 EDID Introduction Extended Display Identication Data is a VESA standard data format that contains basic information about a display device and its capabilities, including vendor information, maximum image size, color characteristics, factory pre-set timings, [...]

Condential 6-2 P1 166 / P1266 / P1266i / P1 166P / P1266P 6-2 Equipment Needed Software - EDID Program (Generic V0.51) - EDID File Hardware - Projector - Generic Fixture (80.00001.001) for EDID Key-in (Fixture: JP3 must be closed) - Power cord for Projector (42.53506G002) - RS-232 9 Pin Cable (pin to pin, F-M) (42.83C07G001) - Monitor - PC - VGA[...]

Condential 6-3 P1 166 / P1266 / P1266i / P1 166P / P1266P 6-3 Setup Procedure (VGA) 1. Connect all ports (1) Connect P1 of Fixture with COM Port of PC/Laptop by RS232 Cable. (2) Connect P2 of Fixture with VGA port of Projector by VGA Cable. (3) Plug Power Adapter to Power CNN. (4) Plug Power Cord to projector . Note: Y ou must conrm that the [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 6-4 6-4 EDID Key-In Procedure 1. Execute EDID Program (1) Click on "EDID" to execute EDID program. 2. Process (1) Check the COM port is COM 2" (Select the COM port which you are using). (2) Click the Model button. (3) Choose the source le "ACER_P1266 EDID-B.ini (*.ini)&[...]

Condential 6-5 P1 166 / P1266 / P1266i / P1 166P / P1266P 5 6 7 5. Finish (1) "OK" will be shown on the screen. 6. Read EDID information (1) In the Read item,select "Analog" and "T rans". (2) Please press "Read" button. 7. Read EDID information (1) EDID Informations will show the result. (1) (2)[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 6-6 6-5 Setup Procedure (HDMI) 1. Connect all ports (1) Connect P1 of Fixture with COM Port of PC/Laptop by RS232 Cable. (2) Connect P2 of Fixture with P3 by DVI Cable. (3) Plug P4 to HDMI Port of the Projector . (4) Plug Power Adapter to Power CNN. ( 5) Plug Power Cord to P12660 unit. Note: [...]

Condential 6-7 P1 166 / P1266 / P1266i / P1 166P / P1266P 2. Process (1) Check the COM port is "COM 2" (Select the COM port which you are using). (2) Click the "Model" button. (3) Choose the source le "ACER_P1266 EDID-B.ini" and then open it. 3. Process (1) Key in the serial number into the barcode blank space. ([...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential 6-8 5. Finish (1) "OK" will be shown on the screen. 6. Read EDID information (1) In the Read item, select "Digital" and "T rans". (2) Please press "Read" button. 7. Read EDID information (1) EDID Informations will show the result. 5 7 6 (1) (2)[...]

Condential 6-9 P1 166 / P1266 / P1266i / P1 166P / P1266P 6-6 Default Language Reset (1) Hold on “Down” button then plug in the Power Cord. Note: At this moment, Power LED turns blue while T emp LED ashes in red for about 4s, then release the “Down” button . (2) After that, please check the LED status and judge the actions as the foll[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential I Appendix A ITEM P ART NO. DESCRIPTION SUPPL Y P AR TS 70.8BA18GR01 ASSY F AN MODULE P1266(SERVICE) V 1 61.8BA04G002 F AN SHIELDING P1 166 2 85.0A123G050 SCREW P/F MECH M3*5 Ni 3 52.8BA05G001 LAMP BLOWER RUBBER P1266 4 49.8BA01G001 SUNON 80*25MM AXIAL F AN (125C 5 43.8BB01G001 THERMAL SWITCH[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential II ITEM P ART NO. DESCRIPTION SUPPL Y P ARTS 70.8BA20GR01 ASSY FRONT COVER MODULE P1266(SERVICE) V 1 51.8BA04G002 FRONT COVER P1 166 2 51.87H09G001 FRONT IR LENS XD1 171D 3 61.8BA12G001 ACER LOGO P1266 4 80.87M05G001 PCBA IR SENSOR BD FOR EP761 V 5 61.00079G001 GROUNDING CABLE CLAMP FN-008 6 [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential III ASSY T OP COVER MODULE[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential IV ITEM P ART NO. DESCRIPTION SUPPL Y P ARTS 70.8BA21GR01 ASSY TOP COVER MODULE P1266(SERVICE) V 1 51.8BA16G002 KEYP AD MODULE P1 166 2 51.8BA1 1G002 ZOOM RING HOLDER P1 166 3 51.8BA12G002 ZOOM RING P1 166 4 85.Y A123G040 SCREW(T APPING FLA T HEAD NI M3* 5 42.00303G01 1 FFC KEYP AD T O M/B 24[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential V ITEM P AR T NO. DESCRIPTION SUPPL Y P ARTS 70.8BA15GR01 ASSY COLOR WHEEL MODULE P1266(SERVICE) V 1 23.8BA19G001 COLOR WHEEL YO 6SCW R85Y37G90C 2 80.87Y04G001 PCBA PHOTO SENSOR BOARD FOR PD7280 V 3 85.1A126G040 SCREW P AN MECH M2.6*4 Ni 4 52.83615G001 COLOR WHEEL DISC RUBBER, EzPro755 5 61.8[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential VI ASSY BOTT OM COVER MODULE PP1270H5350[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential VII ITEM P ART NO. DESCRIPTION SUPPL Y P AR TS 70.8BA14GR01 ASSY BOTT OM COVER MODULE P1266(RMA) V 1 75.8BA03G002 ASSY BOTT OM COVER FOR K-LOCK P1 166 2 52.8BA03G002 ELEVTOR FOOT P1 166 3 51.8BA10G002 ELEV A TOR FOOT PLASTIC P1 166 V 4 61.86814G001 ELEV A T OR EXTEND SPRING PD120 5 61.85913G0[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential VIII ASSY MAIN BOARD MODULE[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential IX ITEM P ART NO. DESCRIPTION SUPPL Y P AR TS 70.8BE06GR01 ASSY MAIN BOARD MODULE P1 166 (SERVICE) V 70.8BA17GR01 ASSY MAIN BOARD MODULE P1266 (SERVICE) V 1 80.8BA01G001 PCBA MAIN BD FOR P1266 1 80.8BE01G001 PCBA MAIN BD FOR P1 166 2 51.8BA19G002 MB T OP MYLAR P1 166 3 41.85E06G002 GASKET W13[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential X ASSY LAMP MODULE[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XI ITEM P AR T NO. DESCRIPTION SUPPL Y P ARTS SP .8BE01GC01 LAMP MODULE FOR PROJECT OR P1 166/P1266 V 1 23.8BA15G001 LAMP E20.8 180W OSRAM 2 61.8BA05G002 LAMP TOP HOLDER P1 166 3 51.8BA14G002 LAMP BOTT OM BASE P1270 4 61.8BA01G001 LAMP HOLDER E20.8 P1266 5 61.8BA06G001 LAMP CLAMP T OP P1266 6[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XII ITEM P ART NO. DESCRIPTION SUPPL Y P AR TS 70.8BE07GR01 ASSY IO COVER MODULE P1 166 (SERVICE) V 70.8BA19GR01 ASSY IO COVER MODULE P1266 (SERVICE) V 1 51.8BA05G002 DESCRIPTION 2 35.8BA01G002 IO COVER P1 166 3 35.8BA02G001 MODEL NAME LABEL P1266 3 35.8BE01G001 MODEL NAME LABEL P1 166 ASSY I[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XIII ASSY ENGINE BOTT OM MODULE ITEM P AR T NO. DESCRIPTION SUPPL Y P AR TS 1 51.88N01G001 ENGINE BOTT OM COVER PC945 X15 2 52.88N05G001 RELA Y RUBBER 3 52.85808G001 PORON LENS BLACK XB31 4 23.88N02G001 YO MIRROR1 FOR X15 5 61.88N1 1G001 MIRROR SPRING SUS301 X15 6 51.88N29G001 T APE 3M J1350 [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XIV ASSY LAMP DRIVER MODULE[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XV ITEM P ART NO. DESCRIPTION SUPPL Y P AR TS 1 42.81G01G001 CABLE W .A. 2P #20 160mm LAPS T V 2 42.00422G001 W .A 5P 150mm LAMP DRIVER TO M V 3 85.3A122G040 SCREW CAP MECH M2*4 Ni 4 42.0043EG002 W .A. 2P#20 FEMALE 6KV 85MM LAM 5 51.8BA08G002 LAMP DRIVER HOLDER P1266 6 75.8BA01G001 ASSY OSRAM[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XVI ASSY BOTT OM HOUSING MODULE[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XVII ITEM P AR T NO. DESCRIPTION SUPPL Y P ARTS 1 70.8BA10G001 ASSY BOTTOM COVER MODULE P1266 2 70.8BA02G001 ASSY LAMP DRIVER MODULE P1266 3 70.8BE01G001 ASSY ENGINE MODULE P1 166 3 70.8BA03G001 ASSY ENGINE MODULE P1266 4 70.8BE02G001 ASSY MAIN BOARD MODULE P1 166 4 70.8BA04G001 ASSY MAIN BOA[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XVIII 28 85.1A326G060 SCREW P AN HEAD MECH M2.6*6 BLACK 29 85.1A323G080 SCREW P AN MECH M3*8 BLACK ‘GRE 30 41.83C01G001 EMI GASKET W13*H15*L40 31 41.89B02G001 EMI T APE W*20/L*70 32 41.85Y04G002 EMI GASKET (S-VIDEO & S-VIDEO) 33 51.8BA22G001 BOTT OM LEFT INNER MYLAR P1266 34 51.8BA23G00[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XIX ASSY ENGINE MODULE[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XX ITEM P ART NO. DESCRIPTION SUPPL Y P AR TS 1 51.8BA07G002 FOCUS RING P1266 V 70.8BA16GR01 ASSY ENGINE MODULE P1266(SERVICE) V 2 61.88N39G001 STOP MASK MG X15 3 81.1A126G060 SCREW P AN MECH M2.6*6 Ni 4 23.8BA01G001 PROJECTION LENS YM25 5 52.88N02G002 PROJECTION LENS RUBBER NEW X15 6 70.8BA0[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XXI 22 48.87K01G001 DMD T ype-X 800x600 PIXEL 0.55’ XGA (FOR P1 166) V 23 61.88N15G001 DMD MASK SUS301,X15 24 52.88N04G002 DMD RUBBER NEW 1.3T X15 25 61.88N01G003 ENGINE BASE MG X15 26 52.88N01G001 OFF RA Y RUBBER,X15 27 61.88N05G001 OFF RA Y PLA TE AL5052,X15 28 87.FL030G008 W ASHER FLA T [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XXII D.C.P1 166/P1266[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential XXIII ITEM P ART NO. DESCRIPTION SUPPL Y P AR TS 1 70.8BA01G001 ASSY BOTTOM HOUSING MODULE P1266 1 70.8BE04G001 ASSY BOTTOM HOUSING MODULE P1 166 2 70.8BA06G001 ASSY FRONT COVER MODULE P1266 SP .8BE01GC01 LAMP MODULE FOR PROJECT OR P1 166/P1266 V 3 70.8BE05G001 ASSY LAMP MODULE P1266 4 70.8BA[...]

Condential P1 166 / P1266 / P1266i / P1 166P / P1266P I Appendix B I. Serial Number System Denition Serial Number Format for Projector (take P1 166 for example) EYJ6901001 820 00000 59 0 1 1 2 3 4 5 6 1 : EYJ6901001 = Part Number 2 : 820 = Date Code (ex:200 8 = 8, the twentieth week of the year = 20) 3 : 00000 = Serial Numbers 4 : 59 = Manufa[...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential II II. PCBA Code Denition PCBA Code for Projector A B XXX XXXXXXXXX CC XXX EEEE 1 : ID 2 : V endor Code 3 : Firmware V ersion 4 : P/N 5 : MB version 6 : Date Code 7 : S/N 1 2 3 7 6 5 4[...]

Condential P1 166 / P1266 / P1266i / P1 166P / P1266P I Appendix C RS232 function command summary table General command type (Projector “receives” commands) No Code (character) Function feature 1 OKOKOKOKOK Power On 2 * 0 IR 001 Power On 3 * 0 IR 002 Power Off 4 * 0 IR 004 Keystone 5 * 0 IR 006 Mute 6 * 0 IR 007 Freeze 7 * 0 IR 008 Menu 8 * [...]

P1 166 / P1266 / P1266i / P1 166P / P1266P Condential II No Code (character) Function feature 33 * 0 IR 034 Video: Sharpness adjustment 34 * 0 IR 035 Query Model name 35 * 0 IR 036 Query Native display resolution 36 * 0 IR 037 Query company name 37 * 0 IR 040 Aspect ratioL.Box (Not supply) 38 * 0 IR 041 Aspect ratio 1:1 (Not supply) 39 * 0 IR 04[...]