Advantech FPM-3150G manuale d’uso

FPM-3150G Series 15" XGA TFT LCD Industrial Monitor with VGA and DVI Inputs User Manual[...]

FPM-3150 Series User Manual ii Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Lt d. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, cop ied, t[...]

iii Product Warranty (2 years) Advantech warrants to yo u, the original purchaser, that each of its prod- ucts will be free from defects in mat erials and workm anship for two years from the date of purchase. This warranty does not apply t o any products which have b een repaired or altered by persons other than repair perso nnel authorized by Adva[...]

FPM-3150 Series User Manual iv FCC Class B This equipment has been tested and f ound to comply with the li mits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These li mits are designed to provide reasonable protection against harmful interfer- ence when the equipment is operated in a residential environment. This equipment gen[...]

v Packing List Before installing yo ur equipment, mak e sure that the foll owing materials have been received: • FPM-3150G Series flat panel monitor • Accessory pack, including: - AC/DC adapter - AC/DC power adapter bracket - DC in Power Cord Bracket x 1 piece - Video Signal Cable, 1.8m - Panel/Wall mount bracket x 2 - Panel sponge x 4 - RS-232[...]

FPM-3150 Series User Manual vi Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this e quipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for clean- ing. 4. For plug-in equipment, the power outlet socket must be locat[...]

vii 15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCON- TROLLED ENVIRONMENT WHERE THE STORAGE TEM- PERATURE IS BELOW -20° C (- 4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE E QUIPMENT. The sound pressure level at the oper ator's position according to IEC 704- 1:1982 is no more than 70dB(A). DISCLAIMER: This set of instructions is given accor[...]

FPM-3150 Series User Manual viii 12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät gelangen. Dies könnt e einen Brand bzw. elektrischen Schlag auslösen. 13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der ele- ktrischen Sicherheit nur von authori siertem Servicepersonal geöff- net w[...]

ix Table of Contents Contents Chapter 1 Introd uction ..................................................... 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Specifications ...... .............. ............... .............. .............. ..... 2 1.3 LCD Specification ......................... ..[...]

FPM-3150 User Manual x C.2.10 Mode Information Menu .... ........... ......... ........... ........... 31 C.2.11 Memory Recall M enu .... ......... ........... ........... ........... .... 32 C.2.12 Exit Menu ............. ......... ........... ......... ........... ........... .... 33 C.2.13 Hot Keys ...... ......... ........... ........... ......[...]

2 CHAPTER 1 Introduction This chapter includes: • Introduction • Specifications • LCD Specification • Power Consumption • Connectors • Dimensions[...]

FPM-3150 Series User Manual 2 Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3150G is a 15" color TFT LCD flat panel monitor built specifically for in dustrial applications. With the optional to uchscreen, FPM-3150G is an excellent and user -friendly system control interface. In addition to its usual appl ication as an LCD panel [...]

3 Chapter 1 Touchscreen (Optional) • Type: 8 wire, an alog resistive • Resolution: 1024 x 1024 • Light Transmission: >80% (Gouge H ardness is greater tahn 4H p er ASTM D3363-92 for HCC01, HCG10 and HCG12 • Operating Pressure: 30 ~ 45 gram for stylus pen contact bounce < 10 ms • Controller: USB & RS-232 interface • Power Consum[...]

FPM-3150 Series User Manual 4 1.5 Connectors The following connectors are situ ated on the left hand side of the FPM-3150G Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15-pin DB-15 connector locatd on th e left side of the system unit. DVI Port (DVI -D) Connected with a standard DV I connector thru I[...]

5 Chapter 1 1.6 Dimensions Figure 1.1: FPM-3150G Dimensions[...]

FPM-3150 Series User Manual 6[...]

2 CHAPTER 2 Mounting • Wallmount ing • Panel Mounting • Rack Mounting • Desktop Mounting • Swing Arm Mounting[...]

FPM-3150 Series User Manual 8 Chapter 2 Mounting 2.1 Mounting the Monitor The FPM-3150G Series can be mounted in many different ways. The versatility of the FPM-3150G mount s enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting FPM-3150G can be m ounted directly on a wall with pa nel mounting brackets. Please refer to figure 2[...]

9 Chapter 2 2.1.2 Panel Mounting If you need to install the FPM-3150G series in a panel, please release the mounting brack ets by detaching four screws on rear side and fix them o n the top and bottom with screws. Figure 2.2: Panel Mounting (396 x 296 mm) Panel Mounting Brackets[...]

FPM-3150 Series User Manual 10 2.1.3 Rack Mounting (Optional) If you need to install the FPM-3150G on a rack, you must order the rack mount kit for FPM-3150G (Part Numb er is FPM-3150G-RMKE). Attach the two rack mounting brackets on each side of FPM-3150G with 12 screws, then affix the monitor in the rack. Figure 2.3: Rack Mounting Brackets[...]

11 Chapter 2 2.2 Desktop, Swing-ARM for FPM-3150G The FPM-3150G Series can be mounted in other ways. These is a desktop stand for desktop use and it can also be attached to a swing-arm bracket. 2.2.1 Desktop Stand The panel-mount bracket is at tached to the rear of the FPM-3150G to become a desktop stand. (Refer to figure 2. 4) Simply detach the sm[...]

FPM-3150 Series User Manual 12 2.2.2 Swing-ARM (VESA Compliant) FPM-3150G has been designed wi th support for the VESA Arm stand ard. Refer to figure 2.5. Detach the mounting brackets on the rear side, and attach the FPM-3150G onto the VESA ARM Mount. Figure 2.5: Swing-ARM for FPM-3150G[...]

2 APPENDIX A Touchscreen[...]

FPM-3150 Series User Manual 14 Appendix A Touchscreen A.1 Introduction The FPM-3150G Series optional touchscreen uses advanced 8-wire resis- tive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is sp ecially designed for to ugh industrial environments, and has been approved to FCC Class B standards. A[...]

15 Appendix A 4. Linearity 4.1 Linear Test Specifications Directio n X: <1.5 % Directio n Y: <1.5 % 4.2 Linearity T est Apply voltage (DC5V) to upper (or lower ) electro des, output voltage Vx or Vy on the other electrodes is measured at every regular intervals. Linearity is the value of max. error voltage 5. Environment Specifications 5.1 Op[...]

FPM-3150 Series User Manual 16 A.3 Installing Driver for Windows OS The touchscreen h as drivers for Windows 2 000 /XP/2003/Vi sta. You should read the instruction s in CD -ROM Disk Touchs creen section care- fully before you attempt installati on. The FPM-3150G-XCE, RCE need to install Penmount 6000 driver. Pl ease find Penmount 6000 folder and in[...]

2 APPENDIX B Setting Serial Data for Expansion[...]

FPM-3150 Series User Manual 18 Appendix B Setting Serial Data for Expansion B.1 Setting Serial Data for Expansion The twelve kinds of timin gs below are already programmed in this mod- ule. The input synchronous signals are automatically recog nized. Resolution Vertical Frequenci es 56 Hz 60 Hz 70 Hz 72 Hz 75 Hz Pass Fail Pass Fail Pass Fail Pass F[...]

2 APPENDIX C OSD Operation Keypad[...]

FPM-3150 Series User Manual 20 Appendix C OSD Operation Keypad C.1 OSD Board Overview The OSD keypad, including six keys and a two colo r indicator, is designed as the OSD operation interface C.1.1 OSD Button Description C.1.2 LED Function Butto ns Descriptions Power Turn the monit or power ON or OFF. Auto/Exit Automatically adjust th e clock, phas[...]

21 Appendix C C.2 OSD Key Functions Each selected value is stored into LCD memory after SEL sig nal input or time out. The stored values are not aff ected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turn ed off before time out. TIME OUT Æ 5-6 seconds ( Can be se[...]

FPM-3150 Series User Manual 22 C.2.2 Input Sourc e Select • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmati on • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN • Available K ey Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last m[...]

23 Appendix C 4. Auto Select Input • ON Æ start from default setting and scan the inputs by followi ng sequence from ANALOG INPUT, DIGITAL INPUT, S-VIDEO INPUT, and CVBS INPUT. • OFF Æ start from default setting C.2.3 Contrast/ Brightness Setting • Generate Main Menu Select by Left and Right But ton, press Menu Button for selection confirma[...]

FPM-3150 Series User Manual 24 • Available K ey Functions RECALL VALUE – User Define • Rec1 Æ Pressed to record 1 st setting as recall value followed by current screen se tting • Rec2 Æ Pressed to record 2 nd setting as recall valu e followed by cur- rent screen setting • Recall Æ Switch the setting change by Rec1 and Rec2 while presse[...]

25 Appendix C • Available K ey Functions Power Off the LCD Monitor Increase the gaug e value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A[...]

FPM-3150 Series User Manual 26 C.2.5 Color Temperature Menu • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmati on • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN • Available K ey Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last[...]

27 Appendix C C.2.6 RGB Color Menu • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmati on Select by Left and Right Button, Press Menu Button for selection confi rmation • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN[...]

FPM-3150 Series User Manual 28 • Available K ey Functions Customization setting fo r RGB colors C.2.7 Language Menu • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmati on • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN Power Off the LCD Monitor Increase the gauge value of the se[...]

29 Appendix C • Available K ey Functions C.2.8 OSD Manager • Generate Main Menu Select by Left and Right But ton, press Menu Button for selection confirmati on • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN Power Off the LCD Monitor Increase the gauge va lue of the selected option. Return to last menu Selected to confirm [...]

FPM-3150 Series User Manual 30 • Available K ey Functions C.2.9 Auto Configuration Menu • Generate Main Menu Select by Left and Right But ton, press Menu Button for selection confirmati on • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN Power Off the LCD Monitor Increase the gauge value of the selected option. Return to la[...]

31 Appendix C • Available K ey Functions Auto configuratio n can be set in menu and also can press the without any m enu indication. C.2.10 Mode Information Menu • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmati on • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN Power Off the [...]

FPM-3150 Series User Manual 32 • Available K ey Functions C.2.11 Memory Recall Menu • Generate Main Menu Select by Left and Right But ton, press Menu Button for selection confirmati on • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last m[...]

33 Appendix C • Available K ey Functions C.2.12 Exit Menu • Generate Main Menu Select by Left and Right But ton, press Menu Button for selection confirmati on • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm De[...]

FPM-3150 Series User Manual 34 • Available K ey Functions C.2.13 Hot Keys OSD LOCK/UNL OCK HOT KEYS Press first then press for change this setting, Followed this sequence for the button press so that you can have OSD LOCK and UNLOCK setting Entry OSD LOCK MODE Press HOT KEY, the screen wi ll show this action first • Don’t remove the HOT KEY u[...]

35 Appendix C • Entry OSD UNLOCK MODE • Press HOT KEY, the screen will show this action first • Don’t remove the HOT KEY until the screen indicated this task is fin- ished.[...]

FPM-3150 Series User Manual 36[...]