AirLive FE-200VD manuale d’uso

AirLive FE-200VD Manual 1 FE-200VD 2-Me gaPixel V andal Dome Fish Eye P oE IPCAM Use r ’ s Manual[...]

Copyright and Disclaimer AirLive FE-200VD Manual i Owner's Record The model and serial numbers are located at the bottom of device. Record these numbers in the spaces provided below . Re fer to these numbers whenever you call upon your dealer regarding this product. Model No. ____________________ Serial No. ____________________ T o prevent fir[...]

Copyright and Discl aimer AirLive FE-200VD Manual ii For customers in the U.S.A. This equipment has been tested and found to comp ly with the limits for a digit al device, pursuant to Part 15 of the FCC Rules. Th ese limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener[...]

Copyright and Disclaimer AirLive FE-200VD Manual iii NOTICE T O USERS © 2006~1 1 All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval. WE PROVIDES NO W ARRANTY WITH RE GARD T O THIS MANUAL, THE SOFTW ARE OR OT[...]

T able of Contents i AirLive FE-200VD Manual T able of Content s 1. Intr oducti on ................................................................................................................ .1 1.1 Over view ..............................................................................................................1 1.2 Package Contents ....[...]

T able of Contents AirLive FE-200VD Manual ii 4.4 Schedu le ............................................................................................................ 30 4.4.1 G eneral ....................................................................................................30 4.4.2 Stor age .............................................[...]

1. Introduction AirLive FE-200VD Manual 1 1 1. Introduction 1.1 Overview AirLive FE-200VD is a Fish-Eye V andal Dome Network Camera featured with 2Mega Pixel resolution and superior H.264-A VC performance and rich functions. AirLive FE-200VD includes a fish-eye lens for 360° p anor amic wide angle view without blind spot. The e-PTZ function includ[...]

1. Introduction AirLive FE-200VD Manual 2 Features z Panoramic 360 Degrees Full View z H.264 & MJPEG V ideo Compression z 2 Megapixels Resolution at 1600 x 1200 pixels z T wo-way Audio Support z Mechanical ICR z Micro SD card for Local S torage z Power-Over-Ethernet 802.3af z Advanced e-PTZ z IP66 Weather and V andal Proof housing for Outdoor E[...]

1. Introduction AirLive FE-200VD Manual 3 1.3 Connections 1. RJ45 LAN socket: Connect to PC or Hub/Switch via a 10Base-T Et hernet or 100Base-TX Fa st Ethernet cable. This Ethernet port built with N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please us e Category 5 cable to connect the Network Camera to[...]

1. Introduction AirLive FE-200VD Manual 4 2. DI/DO connector: DI/ DO: Connect to sensor in and alarm out devices Pin Function Description 1 COM 2 RELA Y -NO Digital output implement ation; Pin2 to COM (Pin1) is a Photo-coupled relay on Normal Open status. External device can directly connect to the terminals. However the current that will go throug[...]

1. Introduction AirLive FE-200VD Manual 5 6. Line out (audio out) Connect a loud speaker to the network camera . This function is for voice alerting and two-way audio. 7. BNC Connector The composite video format will be sent out through this connector . User might connect the IP Camera to a monitor or DVR via this connector . 1.4 Mounting the Camer[...]

1. Introduction AirLive FE-200VD Manual 6 4. Mount the camera onto the suit able position, and then fasten the screws. 5. Close the cove r and fasten the screws. 1.5 Inst all the Camera in LAN 1. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN so cket and attach it into the network. 2. Connect the external power supply t[...]

2. Preparation AirLive FE-200VD Manual 7 2 2. Prep aration 2.1 Search and Set up by IPWizard II When you install the Camera on a LAN environment, you have two easy ways to search your Camera by IPWizard II or UPnP™ discovery . Here is t he way to execute IPWizard II to discover Camera’ s IP address and set up related p arameter in a Camera. 2.1[...]

2. Preparation AirLive FE-200VD Manual 8 2.2 UPnP of Windows® XP , V ist a or 7 UPnP™ is short for Universal Plug and Play , which is a networking architecture that provides compatibility among networking equipment, sof tware, and peripherals. This device is an UPnP enabled device. If the operating system, Windows XP , V ista or 7, of your PC is[...]

2. Preparation AirLive FE-200VD Manual 9 Click the targeted Device . Then Internet Explorer will connect to this Network Camera automatically . 2.3 Inst all the Device behind a NA T Router Once installed, the device is accessible on your LAN. T o access the device from the Internet, you must configure your broadband router to allow in coming data t[...]

2. Preparation AirLive FE-200VD Manual 10 (2) Enable UPnP NA T traversal opt ion of the Netw ork Camera Refer to Setting Î Network Î UPnP page for det ail NA T traversal setting. Note that this option is default enabled. (3) Access your Network Camera by DIPS Refer to Setting Î System Î System p age for detail DIPS information. 2.4 Access the D[...]

2. Preparation AirLive FE-200VD Manual 11 3. According your browser ’s security setting, the IE W eb Page may prompt the “Security W arning” window . If so, select “Y es” to insta ll and run the ActiveX control into your PC. Otherwise, the system will load the ActiveX silently . 4. After the ActiveX control is installed and ran, the first[...]

3. Operating the Network Camera AirLive FE-200VD Manual 12 3 3. Operating the Network Camera S tart-up screen will be as follow no matter an ordinary users or an administrator . Configuration Click for configuring the camera settings. Language The device can provide multiple languages to meet customer ’s requirement. Display Mode Click on differe[...]

3. Operating the Network Camera AirLive FE-200VD Manual 13 V ideo Profile The device supports multi-profile function for H.264, MEPG4 and JPEG simult aneously . A user can chose the proper and/or preferred profile which is listed here. Protocol User can select proper streaming protocol according to networking environment. Manual T rigger T rigger m[...]

3. Operating the Network Camera AirLive FE-200VD Manual 14 z Quad view & Quad with source view PTZ control panel: 1. Ch ： Select the channel. (1~4) & (2~4) 2. S tep ： Set the speed of Pan/T ilt Function. (1~10) 3. Pan/T ilt Arrow ： Click to control the Pan/T ilt Function. 4. Zoom ： Digital zoom in/out. (1~10) 5. Move the control pan[...]

3. Operating the Network Camera AirLive FE-200VD Manual 15 Vo l u m e Click S peaker button to activate this function. Scroll the control bars to adjust the audio attribute. Full Screen Enlarge video to full screen display . Pre ss “ESC” key to disable this function. Snap shot Click Snapshot to activate this fu nction. Pr ess Snapshot button to[...]

4. Administrating the Device AirLive FE-200VD Manual 16 4 4. 0B Administrating the Device System Setting This function is only available for a user logs into Camera as administrator . Click on each menu name to display its setting p age. Item Action V ideo Configure bit rate and fr ame rate of video profiles. Camera Adjust camera parameters. Event [...]

4. Administrating the Device AirLive FE-200VD Manual 17 4.1.2 Advanced z S tream Setting Note: Configuration of stream 2 is the same as stream 1, but S tream 2 can only be set to 320x240 or 640x480. z R TSP Path The R TSP Path is the stream ID used for R TSP client streaming connection, such as VLC player . The default values are v 00, v01 and v02 [...]

4. Administrating the Device AirLive FE-200VD Manual 18 z Image Format H.264 and MJPEG are available for image fo rmat selection. The term, “image format”, is referring to compression / encodi ng technique. The selection of image format decides the performance of bandwid th and storage requirement. In the request of same video quality , H.264 c[...]

4. Administrating the Device AirLive FE-200VD Manual 19 4.2 Camera: Adjust Camera Parameters Use this menu to set the functions of the camera p arameters of the device. 4.2.1 General Use this function to determine the Auto Con trast Compensation level. z Camera General Setting: Brightness: Set the luminance of image. Hue: Refer to pure color; it mo[...]

4. Administrating the Device AirLive FE-200VD Manual 20 z Audio Setting: Audio Enable: T urn on/off the audio. z Web Record Setting: Save Path / File name: Click on the “Browse” button to select the desired p ath to save as well as naming the video file. z Web Snap shot Image Setting: Save Path / File name: Click on the “Browse” button to s[...]

4. Administrating the Device AirLive FE-200VD Manual 21 4.2.2 Advanced z White balance: Adjustment to compensate for different envir onments in terms of light source. A user can choose auto/hold/sunny/cloudy /indoor , so FE-200VD can determine the correct color compensation due to different light environment. z Exposure: Anti-flicker setting for im[...]

4. Administrating the Device AirLive FE-200VD Manual 22 z Infrared (IR) Cut Filter: The default is automatically switched accord ing to the light intensity . “Enable” indicates the filter is enable to cut IR light to make sure t he color is correct. “Disable” indicates the filter is disabled and allows the infrared (such as IR LED illuminat[...]

4. Administrating the Device AirLive FE-200VD Manual 23 (3) Quad with source view: (4) T riple view: 2. Ceiling Mount: For Choosing Ceiling mount, go back to liv e view . There are 6 kinds of video layout to choose from Original view , Broad view , Quad view , Quad with source view , Double view and T riple view . (1.) Original view:[...]

4. Administrating the Device AirLive FE-200VD Manual 24 (2.) Broad view: (3.) Quad view: (4.) Quad with source view: (5.) Double view:[...]

4. Administrating the Device AirLive FE-200VD Manual 25 (6.) T riple view: 4.3 Event 4.3.1 Event Server 5. Add FTP Server: Click on the “Add FTP” to exp and FTP server setting. FTP Server: Name: Give a name for the FTP server Network Address: Input the netwo rk address of the FTP server Upload Path: Choose the desired upload path for event s Po[...]

4. Administrating the Device AirLive FE-200VD Manual 26 z Add HTTP Server: Click on the “Add HTTP ” to exp and HTT P server setting. HTTP Server: Name: Give a name for the HTTP server URL: Input the network address of the HTTP server Username / Password: I nput the username and pa ssword of the HTTP . z Remove: Click “Remove” to delete sele[...]

4. Administrating the Device AirLive FE-200VD Manual 27 4.3.2 Motion Detection z T o add a motion detection area: 1. Click on “Add” to set up a detecti on area. (Setup p anel will be expanded) 2. Give a name to this window area. 3. Select the trigger level and sensitivity for this detection window . (0~100, low~high) 4. Select color for detecti[...]

4. Administrating the Device AirLive FE-200VD Manual 28 5. Draw detection window on the image. 6. Once everything is done, click on “Sav e” to save the c onfiguration made. Configured detection window will be displayed in motion detection list. (Circled in blue) Note: 1. Maximum number of detection window is 10. 2. Motion Detection windows need[...]

4. Administrating the Device AirLive FE-200VD Manual 29 4.3.3 I/O Ports AirLive FE-200VD supports 1 photo-coupled re lay inputs and 1 relay output s. Refer to “ Appendix A: I/O T erminal Connectors ” for detail pin description and application. The below table shows the st atus of t he external trigger/alarm devices. 4.3.4 Event Configuration 1.[...]

4. Administrating the Device AirLive FE-200VD Manual 30 5. The trigger condition is Motion Detection. The responding actions can be “Upload images” and “Act ivate Output Port” and “Send Email Notification” and “Send HTTP Noti fication to” and “Send Message Notification (TCP)”. Click on “Save” to save the configuration made. [...]

4. Administrating the Device AirLive FE-200VD Manual 31 4.5 Network 4.5.1 General Device IP configuration, in cludes DHCP and S tatic IP setti ng. “Enable ARP/Ping” enable device to accept ARP or ping pa ckets from the network. Disable this option may provide extra security from intentional ping. z DHCP Service: S tand for Dynamic Host Configur[...]

4. Administrating the Device AirLive FE-200VD Manual 32 Enable this checked box when a DHCP server is installed on the network to issue IP address assignment. With this setting, the IP address is assigned automatically . If this device can not get an IP address within li mited tries, the device will assign to the default IP address, 192.168.1.100, [...]

4. Administrating the Device AirLive FE-200VD Manual 33 4.5.2 Advanced Enable or configure other network functions. z NTP: Configure a NTP (Network T ime Protocol) se rver , so that the device system date and time can be synchronized with a specif ied T ime Server or DHCP server . z HTTP: Set the HTTP port that will be applied for Web UI access. z [...]

4. Administrating the Device AirLive FE-200VD Manual 34 4.5.4 DDNS (Dynamic DNS) Dynamic DNS configuration; the network device can be assigned with a host name by registering this service (Internet access required). z Host Name: Assigned name that will be used for access to the device z User Name/Password: Account authentication for logging to this[...]

4. Administrating the Device AirLive FE-200VD Manual 35 4.6 System 4.6.1 Information Lists - System and Network configurations. z Firmware V ersion: This information shows the firmware version of the device. 4.6.2 User Use this menu to add, update, or remove the usernames and passwords of the Administrator and viewer . Note: For configuration setti[...]

4. Administrating the Device AirLive FE-200VD Manual 36 4.6.3 Day & Time Y ou can setup the device or make it synchroni zed with PC or remote NTP server . Also, you may select your time zone in order to synchronize time locally . z Current Server T ime: Displaying the date and ti me of the device. z Synchronize with computer time: Click this op[...]

4. Administrating the Device AirLive FE-200VD Manual 37 z Reboot: The device is restarted without changing any of the network settings. I t means the IP address of the device will not change after firmware upgrade. z Load Default (Excluding Network setting): The unit is restarted and most current sett ings are reset to fa ctory default values. This[...]

4. Administrating the Device AirLive FE-200VD Manual 38 1. Close all other application programs whic h are not necessary for firmware update. 2. Make sure that only you access this device while firmware updating. 3. Disable Motion Detection function. 4. Click “ Browse ” button. Select the Fi rmware binary file. ( Note that it must make sure tha[...]

4. Administrating the Device AirLive FE-200VD Manual 39 4.6.5 Log Service Most system operations and / or process will be kept in a log system. The link provides the review of these records. 4.7 Customize This page provides the user features to cust omize the outlook of t he web user interface There are two types of layout settings: Us e Default Lo[...]

4. Administrating the Device AirLive FE-200VD Manual 40 z Use Custom Settings: The allowed modifications are changing of Background / T ext Color , Background picture, T itle, Descrip tion, Logo Link and Logo.[...]

5. Appendix AirLive FE-200VD Manual 41 5 5. 0B Appendix Appendix A: Alarm I/O Connector This Network Camera provides a general I/O terminal block. Pin Function Description 1 COM 2 RELA Y -NO Digital output implement ation; Pin2 to COM (Pin1) is a Photo-coupled relay on Normal Open status. External device can directly connect to the terminals. Howev[...]

5. Appendix AirLive FE-200VD Manual 42 z Explanation of External I/O Circuit Diagram: z CAUTION! − THE LOW VOL T AGE/ CURRENT CIRCUITS AND HIGH VOL T AGE / CURRENT CIRCUITS ARE IN THE NETWORK CAME RA CIRCUIT . THE QUALIFIED ELECTRICIAN SHOULD DO THE WIRING NOT BY YOURSELF . INCORRECT WIRING COULD DAMAGE NWTWORK CA MERA. YOU COULD RECEIVE THE F A [...]

5. Appendix AirLive FE-200VD Manual 43 Appendix B: T roubleshooting & Frequently Asked Questions Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.264, MPEG4 and JPEG triple compression to providing hi gh quality images. Where H.264 and MPEG4 are standards for video compression and [...]

5. Appendix AirLive FE-200VD Manual 44 The username and password for the first time or after facto ry default reset Username = admin and Password = airlive . Note that it’ s all case sensitivity . Forgot the username and password Follow the steps below . 1. Unplug the power jack to turn of f the camera 2. Short pin 5 and pin 6 with a wire 3. Plug[...]

5. Appendix AirLive FE-200VD Manual 45 Can not work with NA T router • Maybe NA T router does not support UPnP function. Please check user ’s manual of router and turn on UPnP function. • Maybe UPnP function of NA T router is not compatible to the IP camera. Please contact your dealer to get the approval routers list. Some IP cameras are work[...]

5. Appendix AirLive FE-200VD Manual 46 Cannot access the login page and other web pages of the Network Camera from Internet Explorer • Maybe the IP Address of the Network Camera is already being used by another device or computer . T o confirm this possible problem, disconnect the Network Camera from the network first, and then run the PING utili[...]

5. Appendix AirLive FE-200VD Manual 47 Image or video does not appear in the main page. • The first ti me the PC connects to Network Camera, a pop-up Security W arning window will appear to download ActiveX Controls. When using Windows XP , or V ista, log on with an appr opriate account that is authorized to install applications. • Network cong[...]

5. Appendix AirLive FE-200VD Manual 48 The unreadable characters are displayed. Use the operating system of the selected language. Set the Encoding or the Char acter Set of the selected language on the Internet Explorer . Frame rate is slower than the setting. • The traf fic of the network and the object of the image affect the frame rate. The ne[...]

5. Appendix AirLive FE-200VD Manual 49 The color of the image is poor or strange. • Adjust White Balanc e. • T o insure the images you are viewing are the best they can be, set the Display property setting (color quality) to 16bit at least and 24 bit or hi gher if possible within your computer . •The configuration on the device image display [...]

5. Appendix AirLive FE-200VD Manual 50 If you want to detect any other devices conf licts with the IP address of Network Camera, also can utilize the PING command but you must disconnect the device from the network first. Appendix D: Bandwid th Estimation The frame rate of video transmitted from the device depends on connection bandwidth between cl[...]

5. Appendix AirLive FE-200VD Manual 51 (SXGA) per frame @ 15fp s Note : Audio streaming also takes bandwidth around 32kbp s. Some xDSL/Cable modem upload speeds could not even reach up to 128 kbps. Thus, you may not be able to receive good quality video while also streaming audio on a 128 kbps or lower connection. Even though the upload speed is mo[...]

5. Appendix AirLive FE-200VD Manual 52 Motion Detection Up to 10 motion detection areas with included or excluded options Alarm Events File upload via FTP ,SD Card or email Notification via email, HTTP , External output activation General RAM 128MB ROM 2GB Power Supply 12V DC external power adapter PoE IEEE 802.3af Power Consumption 5W IP Level IP6[...]

5. Appendix AirLive FE-200VD Manual 53 Manually installing the device with a router on your network is an easy 3–step procedure as following: (1) Assign a local/fixed IP address to your device 　 (2) Access the Router with Y our Web browser 　 (3) Open/Configure Virtual Se rver Ports of Y our Router 　 (1) Assign a local/fixed IP address to yo[...]

5. Appendix AirLive FE-200VD Manual 54 Y our W AN IP Addre ss will be listed here. Note : Because a dynamic WA N IP can change from time to time depending on your ISP , you may want to obtain a S tatic IP address from your ISP . A S tatic IP address is a fixed IP address that will not change over time and will be more convenient for you to use to a[...]

5. Appendix AirLive FE-200VD Manual 55 Private Port section, click Apply . • Scheduling should be set to Always so that the camera images can be accessed at any time. A check mark appearing before the entry name will indi cate that the ports are enabled. Import ant : Some ISPs block access to port 80. Be sure to check with your ISP so that you ca[...]

5. Appendix AirLive FE-200VD Manual 56 Appendix G: DDNS Application z Preface If you have a Cable modem or xDSL, this is a great way to host your own Networked Device or other TCP/IP Service. Ge t your own domain lik e www .yourname.com, www .yourname.com.tw etc. (Note: This dom ain must be registered with Internic via registration authorities such[...]

5. Appendix AirLive FE-200VD Manual 57 (3). After the columns show up at the left side, click “ Create Account ”. (4). Fill the application agreem ent and necessary information. a. Username b. E-mail address and confirmation c. Password and confirmation d. Submit all the input informa tion and finish creating an account[...]

5. Appendix AirLive FE-200VD Manual 58 (5). Check your e-mail mailbox. There will be an e-mail with a title “Y our DynDNS Account Information“. Click the hyperlink addr ess to confirm the DDNS service that you just applied. Then DDNS you applied activated. Click these two options[...]

5. Appendix AirLive FE-200VD Manual 59 (6). Enter the web page http://www .dyndns.org/ again. Input your username and password that you just applied to login adm inistration interface of D DNS server . (7). If the correct username and password are input, you can see the following picture at the top-right of the login page. Click to confirm Input yo[...]

5. Appendix AirLive FE-200VD Manual 60 (8). Click the “ Services ”. (9). Click the “ Dynamic DNS ”. (10). Click the “ Get S tarted ”.[...]

5. Appendix AirLive FE-200VD Manual 61 (1 1). We could create a domain name without any c harge at this step . First, we input the host name. (Pink No.1) Then we pick a domai n that is easy to remember . (Pink No.2) The 3rd step is to click “Of fline Hostname” fr om Service T ype. (Pink No.3) Finally , click the “Create Host” to submit the [...]

5. Appendix AirLive FE-200VD Manual 62 Appendix H: Power Line Frequency COUNTRY VOL T AGE FREQUENCY COMMENTS Argentina 220V 50 Hz *Neutral and line wires are reversed from that used in Australia and elsewhere. Australia 230V* 50 Hz *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially changed to 230V , 240V is[...]

5. Appendix AirLive FE-200VD Manual 63 Portugal 230V 50 Hz S pain 230V 50 Hz Sweden 230V 50 Hz Switzerland 230V 50 Hz T aiwan 1 10V 60 Hz Thailand 220V 50 Hz United Kingdom 230V* 50 Hz *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially changed to 230V , 240V is within tolerances and commonly found. United S[...]

5. Appendix AirLive FE-200VD Manual 64 Appendix J: Enable UPnP of Windows XP Use the following steps to enable UPnP settings only if your operati ng system of PC is running Windows XP . Go to St art > Settings . Click Control Panel Click Add or Remove Programs[...]

5. Appendix AirLive FE-200VD Manual 65 Click Add/Remove Windows Components The following screen will appear: Select Networking Services Click Details[...]

5. Appendix AirLive FE-200VD Manual 66 Select Universal Plug and Play Click Ok Click Next[...]

5. Appendix AirLive FE-200VD Manual 67 Please wait while Setup configures the components. Click Finish[...]