AOC LM722 manuale d’uso

英文 TABLE OF CONTENTS FOR YOUR SAFETY ------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 2 BEFORE YOU OPERATE THE MONITO R --------------------- 2 FEATURES -------------------------------------------------------- 2 PACKING LIST --------[...]

英文 1 Before operating the monitor, pleas e read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply w ith the limits for a Class B digital device, pursuant to Pa rt 15 of the FC[...]

英文 2 PRECAUTIONS z Do not use the monitor near water, e.g. near a bathtub, w ashbow l, kitchen sink, laundry tub, sw imming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance. Use only a cart or stand recommended by t[...]

英文 3 SPECIAL NOTES ON LCD MONITORS The following symptoms are normal w ith LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven br igh[...]

英文 4 INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWERCORD Pow er Source: 1. Make sure that the power cord is the correct type required in y our area. 2. This LCD monitor has an Internal universal power supply that allow s operation in either 100/120V AC or 220/240V AC voltage area (No u[...]

英文 5 CONTROLS AND CONNECTORS SIGNAL CABLE Connecting the Signal Cable: Plug the Signal Cable one end to LCD monitor’s “ DSUB-Input” socket , the ot her end to the computer's VGA port and tighten the two screw s on the cable connector. Connecting the Power Cord: Plug the AC-power cord one end to LCD monitor’s AC input socket , the o[...]

英文 6 ADJUSTING THE VIEWING ANGLE • F or optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’ s angle to your ow n preference. • Hold the stand so y ou do not t opple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from -5 ° to 20 ° . Figur[...]

英文 7 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the moni tor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjust ed to your personal preferences. • T he power cord should be connected. • Connect the video cable fr[...]

英文 8 FRONT PANEL CONTROL • Pow er Button : Press this button to switch ON/OFF of monitor’s power. • MENU / ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Brightness/Contrast OSD status. • Contrast / : Adjust contrast or function adjust. • Brightness / : Adjust brightness or function adjust. • Auto Adjust[...]

英文 9 NOTES • Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place s ubject to direct sun light, or excessive dust or mechanical vibration or shock. • Save the original shipping carton and packing materials, as they w ill come in handy if you ever have to ship y our monitor. • For maximum[...]

英文 10 ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Contrast Contrast from Digital-register. Luminance Brightness Backlight Adjustment Focus Adjust Picture Phase to reduce Horizontal-Line noise Image Setup Clock Adjust picture Clock to reduce Vertical-Line [...]

英文 11 Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Yes N/A Auto Adjust the H/V Position, Focus and Clock of picture. Auto Config No N/A Do not execute Auto Config, return to main menu. H. Position Adjust the horizontal position of the OSD. V. Position Adjust the vertic alposition of the OSD. OSD Setup OSD Timeout Adjust[...]

英文 12 PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data [...]

英文 13 TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Po w er Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable i[...]

英文 14 ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is pr operly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitabl e display mode ,set the computer to display m[...]

英文 15 HOW TO INSTALL THE DRIVER-DISK (INF & ICM FILE) FOR FIRST TIME INSTALL : Your system may not recognize your flat-panel monitor,and as a result, y ou may need to complete the follow ing steps for optimum performance of your monitor. 1. Check this LCD MONITOR is pr operly connected to your computer. 2. Restart the computer , when win95/[...]

英文 16 APPENDIX SPECIFICATIONS Driving system T FT Color LCD LCD Panel Size 43.2cm(17.0") Pixel pitch 0.264mm( H ) × 0.264mm( V ) Viewable angle 140 ° (H) 120 ° (V) Response time 16 ms(typical) Video R,G,B Analog Interface Input Separate Sync. H/V T TL H-Frequency 30kHz – 80kHz V-Frequency 55-75Hz Display Colors 16.2M Colors Dot Clock [...]

英文 17 Switch • Auto Adjust Button • / Brightness • / Contrast • Power Button • MENU External Controls: Functions • Contrast • Brightness • Focus • Clock • H. Position • V. Position • Auto Config • OSD Setup • Language • (Warm)Color • (Cool)Color • USER Color temperature • Reset • Exit Power Consumption ( Ma[...]

英文 18 STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY Dos-mode 640 × 350 31.47kHz 70Hz Dos-mode 720 × 400 31.47kHz 70Hz 640 × 480 31.47kHz 60Hz 640 × 480 35.00kHz 66.6Hz 640 × 480 37.50kHz 75Hz VGA 640 × 480 37.86kHz 72Hz 800 × 600 37.879kHz 60Hz 800 × 600 46.875kHz 75Hz 800 × 600 35.16kHz 56Hz 800 × 600 48.01kHz 72Hz SVGA[...]

英文 19 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Detect Cable 3. Blue 11. TXD 4. RXD 12. DDC-Serial Data 5. Ground 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground CONNECTOR PIN ASSIGNMENT[...]